Upload
duongthu
View
225
Download
0
Embed Size (px)
Citation preview
LightStack™ Ultra High Density Fiber EnclosureAs today’s high density Data Centers migrate from 10 to 40 and 100 gigabit speeds, they require low loss
fiber connectivity to support multiple mated connections for flexible patching options over a wide range of
distances and configurations while remaining within link loss budgets. At the same time, these connections
need to be easily accessed and managed to quickly and effectively make changes.
With superior best-in-class features, Siemon’s LightStack ultra high density fiber Plug and Play system offers
superior density, port access and cable management in a sleek, modern enclosure that easily supports
today’s advanced Data Center and storage area network environments, while providing fast, seamless migra-
tion to advanced 40 and 100 gigabit applications.
Mounting optionsRack mounting brackets can beattached at any of 3 horizontalpositions
Visually appealing magnetic door- Easy to open and close- Eliminates potential pinch points
ULtra High Density144 fibers per 1U (LC interface) and 864fibers per 1U (MTP interface)
576 fibers per 4U (LC interface) and 3456fibers per 4U (MTP interface)
Cable Management ClipsUnlatch and swing open for full accessto any jumper
High Capacity DesignHandles both traditional 2mm zipcord and 2fiber, interconnect tight-buffered jumper types
1.
Innovative labelingsolution and port IDDrop-down label stripholder for high visibility
Module Insertion and RemovalCan be quickly and easily installed orremoved from the front or rear of theenclosure
LightStack 1U Front View
SS_LightStack_I.qxp_I 4/19/18 1:56 PM Page 1
2.
LightStack® EnclosuresSiemon’s LightStack ultra high density fiber Plug and Play enclosure offers superior density, port
access and cable management in a sleek, modern enclosure that easily supports today’s advanced data
center and storage area network environments.
Module Insertion and Removal — Can bequickly and easily installed or removedfrom the front or rear of the enclosure
Strain Relief — Swivel tie down allows forsimplistic approach for anchoring trunksand eliminating pinch points
Sliding Bottom Rear Divider — Acts as a rearcable divider between stacked enclosures (inthe out position). Pushes inward to providecomplete access to connectivity at the rear ofstacked enclosures
Mounting Options — Rack mountingbrackets can be attached at any of 3horizontal positions
Part # Description
LS-1U-01 . . . . . . . . . . . . . . . . . . LightStack enclosure, up to 144 LC fibersor 864 MTP fibers, 1U
LS-4U-01 . . . . . . . . . . . . . . . . . . LightStack enclosure, up to 576 LC fibersor 3456 MTP fibers, mounts in 19 in.racks or cabinets, 4U
Ordering Information:
Cable Management Clips — Unlatch andswing open for full access to any jumper
Innovative Labelling Solution — Drop-down label strip holder for high visibility
Innovative Magnetic Door — Opensand closes easily. Eliminates pinchpoints
1U Enclosure 4U Enclosure
1U 4U
Height 43.9 mm (1.73 in.) 176.8 mm (6.96 in.)
Width 482.3 mm (18.99 in.) 482.3 mm (18.99 in.)
Depth 530.6 mm (20.89 in.) 530.6 mm (20.89 in.)
Weight 9.53 kg (21 lb.) 23.58 kg (52 lb.)
Color Black (RAL 9005) Black (RAL 9005)
Label size 204.5mm (8.05 in.) L x 23.5mm (.925 in.) W 204.5mm (8.05 in.) L x 93mm (3.66 in.) W
SS_LightStack_I.qxp_I 4/19/18 1:56 PM Page 2
3.
LightStack® Modules
Ultra Slim Design — LightStack modules have anultra slim design to achieve maximum fiber density
High Fiber Count — Up to 12 fibercount per module
Standard Interfaces — LC to MTPinterface. Available in OM4 and SM
LightStack LC-to-MTP Low Loss Plug and Play modules deliver a quick and efficient way to deploy high-perfor-
mance fiber cabling in a low-profile, high density package. Up to 12 of these ultra-slim modules can be installed
in a single 1U LightStack enclosure, seamlessly providing up to 144 easily-managed LC fiber ports. Available
in OM4 Multimode and Singlemode configurations, these modules offer industry leading loss performance of
just 0.35dB.
Low Loss Options — Low lossperformance (0.35dB perMultimode module)
Rear Module Handles — Handles in therear of module help facilitate removalfrom the back of the enclosure
Multiple Adapter Configurations —Aqua LC and MTP adapters for OM4;Blue LC adapters and black MTPadapters for SM
Ordering Information:
PERFORMANCE SPECIFICATIONSInsertionLoss (dB)
ReturnLoss (dB)
InsertionLoss (dB)
ReturnLoss (dB)
Multimode Singlemode
MTP 0.20 20 0.60 60
LC 0.15 30 0.40 55
MTP to LC 0.35 20 1.00 55
Reference Siemon’s White Paper titled: “The Need for Low-Loss Multifiber Connectivity in Today’s Data Center” for information and guidance on design options, channel mod-els and distances for 10, 40, 100Gb Ethernet and Fiber Channel applications.
Shuttered LC adapters — Optional smallplastic shutter door that opens upon insertionwithout touching the connector endface andsprings back into the closed position uponremoval to ensure protection of empty ports.
Part # Description
LS-12-LC5V-01. . . . . . . . . . . . . . Module, 12 LC-to-MTP fibers, OM4, XGLO 550, aqua LC and MTP adapters
LS-12-LCEV-01 . . . . . . . . . . . . . Module, 12 LC-to-MTP fibers, OM4, XGLO 550, erika violet LC and MTP adapters
LS-12-LCSM-01 . . . . . . . . . . . . . Module, 12 LC-to-MTP fibers, Singlemode, blue LC adapters, black MTP adapters
LS-12-LS5V-01. . . . . . . . . . . . . . Module,12 LC-to-MTP fibers, OM4, XGLO 550, shuttered aqua LC and MTP adapters
LS-12-LSEV-01 . . . . . . . . . . . . . Module, 12 LC-to-MTP fibers, OM4, XGLO 550, shuttered erika violet LC and MTP adapters
LS-12-LSSM-01 . . . . . . . . . . . . . Module, 12 LC-to-MTP fibers, Singlemode, shuttered blue LC adapters, black MTP adapters
SS_LightStack_I.qxp_I 4/19/18 1:56 PM Page 3
LightStack® Adapter Plates
LightStack MTP Adapter Plates
• Ultra slim design to achieve maximum fiber density• Up to 72 fiber count• Handles in the rear of module helps facilitate removal from
the back of the enclosure
Ordering Information:
MTP Adapter Plate
LC Adapter Plate
Key Orientation
B = Aligned (key up to key up)C = Opposed (key up to key down)
Adapter Colour
AQ = Aqua**EV = Erika Violet**BK = Black**GR = Grey*
LS-MP(X)-01(X)(XX)
MTP Port Count2 = 2 MTP Ports4 = 4 MTP Ports6 = 6 MTP Ports
Ordering Information:
Fully ready to support 40 and 100 gigabit applications, LightStack low-loss 0.2dB MTP pass-through
adapters are available in 2, 4 and 6-port designs supporting up to 72 fibers per adapter and are offered in
both aligned and opposed key orientation to accommodate all polarity methods. In addition, LightStack
also offers industry exclusive 12-fiber LC pass-through adapter plates for current 10 gigabit Ethernet or
Fiber Channel SAN applications.
• Used in conjunction with LC BladePatch® RazorCore™ trunksfor rear connections only
• 12 LC fibers
LightStack LC Adapter Plates
* Key Orientation B Only
** Key Orientation C Only
4.
* Optional Shuttered LC adapters feature a small plastic shutterdoor that opens upon insertion without touching the con-nector endface and springs back into the closed positionupon removal to ensure protection of empty ports.
Adapter Colour
BG = Beige AQ = Aqua EV = Erika Violet BL = Blue
LS-L(X)12-01C-(XX)
Shutter Door Option
C = Standard LC adapterS = Shuttered LC adapter
SS_LightStack_I.qxp_I 4/19/18 1:56 PM Page 4
5.
Base 12 MTP to LC BladePatch®
Trunks• LC BladePatch with push pull latch further improves accessibility• Designed to facilitate an interconnect or cross connect point between active
equipment• OM3/OM4 Bend Insensitive Fiber (BIF)• SM Non-Bend Insensitive• 12 Fiber strand count• Specific staggered lengths to active equipment - Nexus, Cisco MDS, Brocade and No stagger• Low Loss performance 0.15 dB for LC and 0.20 dB for Multimode MTP• Standard Loss performance 0.25 dB for LC and 0.60 dB for Singlemode MTP• Integrated cable manager on breakout
L = Low Loss (OM3/OM4 Only)F = Standard Loss (SM Only)
Performance
Jacket Rating
P = PlenumR = RiserL = LSOH
Pulling Eye OptionA = MTP Side (Only available for length >5MC = None
T(X)2(X)(X)(X)(X)(X)(X)(XX)(XXX)(X)
B = 12 Strand Strand Count
LC BP ConnectorLB = RFP (OM3, OM4, SM/UPC)BL = CFP (OM3, OM4, SM/UPC)
MTP GenderM = MTP MaleF = MTP Female
Stagger Type1 = No Stagger
2 = Cisco 9512 & 9412
3 = Cisco NEXUS
4 = Brocade
Length UnitF = FeetM = Meter
Length*Length must be 3 digits Example:003 = 3m010 = 10 ft.
Ordering Information:
L = OM3, XGLO 300 50/125 Multimode AquaV = OM4, XGLO 550 50/125 Multimode AquaE = OM4, XGLO 550 50/125 Multimode Erika VioletA = OS1/OS2, Singlemode Yellow
Fiber Type
Base 12 Next Generation MTP to MTP TrunksSiemon's Next Generation MTP to MTP trunks are designed to achieve 45kg (99.2 lbs.) pull strength to han-
dle more aggressive pathway environments. They come with a foamed zipper pulling eye for quick
removal saving on installation time and are reusable if relocation of a trunk is required after the initial
installation. They are available in 12/24 fiber counts and Low Loss options only.
• OM3/OM4 Bend Insensitive Fiber (BIF)• SM Non-Bend Insensitive Fiber• 12 and 24 Fiber strand counts• Polarity methods A, B and C options• Low Loss performance (0.20dB for Multimode MTP and 0.60dB for
Singlemode MTP)• Integrated breakout and zipper pulling eye work together to achieve
45kg (99.2 lbs.) tensile pull strength• Zipper pulling eye allows for quicker installs - Allows pulling eyes to be reused when relocating trunks
during MAC work
B = 12C = 24
Strand Count
Cable Type
P = PlenumR = RiserL = LSOH
FR2-(X)-(X)(X)(XXX)(X)(X)
Fiber TypeLength Unit
F = FeetM = Meters
Polarity Method (Per TIA-568-C.0)
LengthLength must be 3 digitsExample: 003 = 3m010 = 10 ft.
Ordering Information:
A = Method AB = Method BC = Method C
L = OM3, XGLO 300 50/125 Multimode AquaV = OM4, XGLO 550 50/125 Multimode AquaE = OM4, XGLO 550 50/125 Multimode Erika VioletA = OS1/OS2, Singlemode Yellow
SS_LightStack_I.qxp_I 4/19/18 1:56 PM Page 5
Ordering Length
1 meter (3.3 ft) 1 meter (3.3 ft)
6.
** Order length is measured connector tip to connector tip. Multi-leg ver-sions offered with standard 1 meter legs. Minimum order length is 1meter for 12 strand and 3 meters for 24 strands or greater(See diagram at right)
* Fiber Extenders ship with MTP Adapter for quick transition.
Combining Siemon’s reduced-diameter RazorCoreTM cable with 12-fiber MTP connectors, Plug and Play
Reels are designed to be quickly pulled and connected to Siemon Plug and Play Modules and MTP Adapter
Plates. Custom configurable to precise application requirements, these reels efficiently put high-perfor-
mance, high-density fiber connections exactly where you need them. Extenders offer Male MTP
Connectors on one end and female MTP adapters on the other to allow field extension of MTP Reels.
Base 12 Plug and Play Cable Assemblies
Ordering Information: Non-Armoured
Fiber Count
12 = 1224 = 2436 = 3648 = 4872 = 7296 = 96144 = 144
Fiber Type
Length**
Configuration
F(X)(XX)-(XX)(X)(XXX)(X)-(X) . . . . Fiber Plug & Play cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . assembly, 12 fiber MTP
connectors
Jacket Rating
R = RiserP = PlenumL = LSOH
Length UnitF = FeetM = Meters
R = Standard LossL = Low Loss
(0M3/0M4 only)E* = Standard Loss ExtenderB* = Low Loss Extender
(0M3/0M4 only)
F(X)(XX)-(XX)(XX)(XXX)(X)(X) . . . . Armoured Fiber Plug & Play cablereel assembly, 12 fiber MTP femaleconnectors
Fiber Count
12 = 1224 = 2436 = 3648 = 4872 = 7296 = 96144 = 144
Fiber Type Jacket Rating
AR = Armoured RiserAP = Armoured Plenum
Length UnitF = FeetM = Meters
Ordering Information: Armoured
ConfigurationR = Standard LossL = Low Loss
(0M3/0M4 only)
Polarity Method (Per TIA-568-C.0)A = Method AB = Method BC = Method CBlank = Fiber Extender (FE and FB)
Polarity Method (Per TIA-568-C.0)A = Method AB = Method BC = Method C
6 = OM1, 62.5/125 Multimode Orange5L = OM3, XGLO 300 50/125 Multimode Aqua5V = OM4, XGLO 550 50/125 Multimode AquaEV = OM4, XGLO 550 50/125 Multimode Erika VioletSM = OS1/OS2, Singlemode Yellow
Length must be 3 digitsExample: 003 = 3m
010 = 10 ft.
6 = OM1, 62.5/125 Multimode Orange5L = OM3, XGLO 300 50/125 Multimode Aqua 5V = OM4, XGLO 550 50/125 Multimode AquaEV = OM4, XGLO 550 50/125 Multimode Erika Violet SM = OS1/OS2, Singlemode Yellow
Length**
Length must be 3 digitsExample: 003 = 3m
010 = 10 ft.
Reduced Pathway Fill — Siemon'sRazorCore cable has significantlyreduced cable O.D. resulting in lesscable tray fill and pathway restrictions
Custom Configurations — Availablefrom 12 to 144 fiber counts in increments of 12 fibers
Multiple Fiber Types — Available in Multimode(62.5/125, and laser optimised 50/125OM3/OM4) and Singlemode.
40 Gb/s and 100 Gb/s Ready — Enables simple upgradepath to future 40 Gb/s and 100 Gb/s applications overMultimode 50/125 laser optimised fiber
Note: LSOH versions available. Contact CustomerService for details.
SS_LightStack_I.qxp_I 4/19/18 1:56 PM Page 6
7.
T(X)(X)(X)(XX)(X)(XX)LC(XXX)(X). . . . . . . . . . MTP to LC Trunk (distribution to breakout)
1 meter
> 1 meter
50cm
1 meter
See performance details on page 6.27.
Custom Configurations — Available from 12 to144 fiber counts in increments of 12 fibers
Multiple Fiber Types — Available in Multimode(62.5/125 and laser optimised 50/125 OM3/OM4)and Singlemode.
Base 12 MTP®
to LC Trunks
Utilising high quality Siemon RazorCore™ cable, MTP to LC Trunks offer a connectivity transition from
12-fiber MTP connectors to duplex LC connectors. These may be implemented using Siemon’s MTP to
MTP Adapter Plates to provide direct MTP to LC patching options over a wide range of distances and
infrastructure configurations.
Ordering Information:
Fiber Count
B = 12C = 24E = 36F = 48G = 72H = 96J = 144
Pulling Eye
A = Side AB = Side BC = None
Fiber TypeMM = MaleMF = Female
MTP Connector Gender
Length*
Jacket RatingP = PlenumR = RiserL = LSOH
Length UnitF = FeetM = Meters
Configuration
L = Low Loss (OM3/OM4 only)F = Standard Loss
Length must be 3 digitsExample: 003 = 3m
010 = 10 ft.
6 = OM1, 62.5/125 Multimode Beige5L = OM3, XGLO 300 50/125 Multimode Aqua5V = OM4, XGLO 550 50/125 Multimode AquaEV = OM4, XGLO 550 50/125 Multimode Erika VioletSM = OS1/OS2, Singlemode Yellow
* Minimun order length is 1 meter. Order length is measured connector tip to connector tip. Trunks greater than 1 meter (3.28 ft.) have breakout length of 1 meter. 1 meter trunks have a 50cm breakout length (See diagram below)
SS_LightStack_I.qxp_I 4/19/18 1:56 PM Page 7
8.
TFU(X)(X)(X)(X)(X)(X)(X)(X)(XXX)(X)
Note: These products are made to order. Call for lead time and availability.
Ordering Length(Side A) (Side B)
1 meter 1 meter
Ordering length is measured connector tip to connector tip. 2. 4 unitube duplex, 2.0mm duplex and simplex 900 micron bufferedMinimum order length is 3 meters (9.8 ft).
Fiber CountA = 6B = 8C = 12D = 16E = 24F = 36G = 48H = 72J = 96K = 144
Pulling EyeA = Side AB = Side BC = Side A&BD = None
Fiber Type
Connector Type (Side B)
Cable LengthLength must be 3 digitsExample: 004 = 4m
012 = 12 ft.
Unit of MeasureF = FeetM = Meters
Connector Type (Side A)
Cable Type
P = Plenum - Indoor Distribution (OFNP)R = Riser - Indoor Distribution (OFNR)L = LSOH - Indoor Distribution (IEC 60332-3C)
A = Simplex 900µmB = Duplex 2.0mmC = Uni-Tube Duplex 2.4mm LC BladePatch only
LEG OD (Side A) A = Simplex 900µmB = Duplex 2.0mmC = Uni-Tube Duplex 2.4 LC BladePatch only
LEG OD (Side B)
(3.28 ft.) (3.28 ft.)
A = OS1/OS2, 62.5/125 Singlemode YellowB = OM1, 62.5 Multimode OrangeL = OM3, XGLO 300 50/125 Multimode Aqua V = OM4, XGLO 550 50/125 Multimode AquaE = OM4, XGLO 550 50/125 Multimode Erika Violet
A = LC MultimodeB = LC UPC SinglemodeC = LC APC SinglemodeD = LC BladePatch Multimode RFP Polarity only
E = LC BladePatch UPC Singlemode RFP Polarity onlyF = SC MultimodeG = SC UPC SinglemodeH = SC APC Singlemode
J = ST MultimodeK = ST UPC Singlemode
A = LC MultimodeB = LC UPC SinglemodeC = LC APC SinglemodeD = LC BladePatch Multimode RFP Polarity only
E = LC BladePatch UPC Singlemode RFP Polarity onlyF = SC MultimodeG = SC UPC SinglemodeH = SC APC Singlemode
J = ST MultimodeK = ST UPC Singlemode
2.4mm Unitube Duplex Breakout - LC BladePatch®
XGLO® and LightSystem® Fiber Trunks
900µm Simplex Breakout 2.0mm Duplex Breakout
SS_LightStack_I.qxp_I 4/19/18 1:56 PM Page 8
9.
XGLO® and LightSystem® LC & SCFiber Trunks
JacketType
Fiber StrandCount
Cable Diametermm (in.)
Min Bend Radius Operational
mm (in.)
Min Bend RadiusInstallation
mm (in.)
Max Pulling EyeDiametermm (in.)
*Required DuctDiameter mm (in.)
Riser 6 3.0 (0.12) 30 (1.2) 45 (1.8) 44.5 (1.75) 69.9 (2.75)
Riser 8 3.0 (0.12) 30 (1.2) 45 (1.8) 44.5 (1.75) 69.9 (2.75)
Riser 12 3.0 (0.12) 30 (1.2) 45 (1.8) 44.5 (1.75) 69.9 (2.75)Riser 16 3.8 (0.15) 38 (1.5) 57 (2.2) 44.5 (1.75) 69.9 (2.75)
Riser 24 3.8 (0.15) 38 (1.5) 57 (2.2) 44.5 (1.75) 69.9 (2.75)Riser 36 9.4 (0.37) 94 (3.7) 141 (5.6) 63.5 (2.5) 88.9 (3.5)
Riser 48 9.4 (0.37) 94 (3.7) 141 (5.6) 63.5 (2.5) 88.9 (3.5)Riser 72 9.4 (0.37) 94 (3.7) 141 (5.6) 63.5 (2.5) 88.9 (3.5)
Riser 96 13.2 (0.52) 132 (5.2) 198 (7.8) 88.9 (3.25) 114.3 (4.5)Riser 144 13.2 (0.52) 132 (5.2) 198 (7.8) 88.9 (3.25) 114.3 (4.5)
Plenum 6 3.0 (0.12) 30 (1.2) 45 (1.8) 44.5 (1.75) 69.9 (2.75)
Plenum 8 3.0 (0.12) 30 (1.2) 45 (1.8) 44.5 (1.75) 69.9 (2.75)
Plenum 12 3.0 (0.12) 30 (1.2) 45 (1.8) 44.5 (1.75) 69.9 (2.75)
Plenum 16 3.8 (0.15) 38 (1.5) 57 (2.2) 44.5 (1.75) 69.9 (2.75)
Plenum 24 3.8 (0.15) 38 (1.5) 57 (2.2) 44.5 (1.75) 69.9 (2.75)
Plenum 36 7.5 (0.30) 75 (3.0) 113 (4.4) 63.5 (2.5) 88.9 (3.5)
Plenum 48 7.5 (0.30) 75 (3.0) 113 (4.4) 63.5 (2.5) 88.9 (3.5)
Plenum 72 8.5 (0.33) 85 (3.3) 128 (5.0) 63.5 (2.5) 88.9 (3.5)Plenum 96 13.6 (0.54) 136 (5.4) 204 (8.0) 88.9 (3.25) 114.3 (4.5)
Plenum 144 13.6 (0.54) 136 (5.4) 204 (8.0) 88.9 (3.25) 114.3 (4.5)
LSOH 6 3.0 (0.12) 30 (1.2) 45 (1.8) 44.5 (1.75) 69.9 (2.75)LSOH 8 3.0 (0.12) 30 (1.2) 45 (1.8) 44.5 (1.75) 69.9 (2.75)
LSOH 12 3.0 (0.12) 30 (1.2) 45 (1.8) 44.5 (1.75) 69.9 (2.75)LSOH 16 3.8 (0.15) 38 (1.5) 57 (2.2) 44.5 (1.75) 69.9 (2.75)LSOH 24 3.8 (0.15) 38 (1.5) 57 (2.2) 44.5 (1.75) 69.9 (2.75)
LSOH 36 6.5 (0.26) 65 (2.6) 98 (3.3) 63.5 (2.5) 88.9 (3.5)LSOH 48 6.5 (0.26) 65 (2.6) 98 (3.3) 63.5 (2.5) 88.9 (3.5)
LSOH 72 7.0 (0.28) 70 (2.8) 105 (4.1) 63.5 (2.5) 88.9 (3.5)LSOH 96 12.5 (0.49) 125 (4.9) 188 (7.4) 88.9 (3.25) 114.3 (4.5)
LSOH 144 14.9 (0.59) 149 (5.9) 224 (8.8) 88.9 (3.25) 114.3 (4.5)
*Pulling eye assembly shall be capable of passing through these minimum duct diameter requirements during product installation.Pulling eye max pull force 18.1kg (40lbs)
CABLE — Optical and Physical Specifications
Fiber Type Performance Class
Max Insertion Loss (dB)
Min Return Loss (dB)
62.5/125 µm Multimode, OM1 LightSystem 0.50 25
50/125 µm Laser Optimised Multimode, OM3,OM4 XGLO 0.25 30
Singlemode UPC, OS1/OS2 XGLO 0.40 55
Singlemode APC, OS1/OS2 XGLO 0.40 65
CONNECTORS — Optical Specifications
SS_LightStack_I.qxp_I 4/19/18 1:56 PM Page 9
SS-L
ight
Stac
k R
ev I
4/18
©
2018
Siem
on
10.
STANDARD LOSS ASSEMBLIES
CABLE - OPTICAL AND PHYSICAL SPECIFICATIONS
CONNECTORS - PHYSICAL SPECIFICATIONS
Product Specifications
Fiber Type
MAX Insertion(dB)
MAX Return Loss(dB) Performance Class
MTP LC MTP LC
5L-MM50/125(OM3) 0.50 0.25 20 30 XGLO® 300
5V-MM50/125(OM4) 0.50 0.25 20 30 XGLO 550
SM-LWP SM (OS1/OS2) 0.60 0.40 60 55 XGLO
Fiber Type
MAX Insertion(dB)
MAX Return Loss(dB) Performance Class
MTP LC MTP LC
5L-MM50/125(OM3) 0.20 0.15 20 30 XGLO 300
5V-MM50/125(OM4) 0.20 0.15 20 30 XGLO 550
LOW LOSS ASSEMBLIES
* XGLO singlemode fiber meets low water peak specifications per ITU-TG.652.C
Plug and Play Fiber System OpticalPerformance
Cable Type
Multimode
SinglemodeXGLO50/125 OM3 (850/1300nm)
XGLO50/125 OM4 (850/1300nm)
Fiber Cable Attenuation, MAX (dB/km) 3.0 / 1.0 3.0 / 1.0 0.4/ 0.4/ 0.3*
LED Bandwidth, MIN (MHz/km) 1500 / 500 3500 / 500 N/A
Effective Modal Bandwidth, MIN (MHz/km) 2000 4700 N/A
Cable Outer Jacket, Colour (Per TIA-598-C) Aqua Aqua/ Erika Violet Yellow
ConnectorType
IEC Intermateability
Compliance
TIA Intermateability
Compliance
Housing Colour Boot Colour
MM SM MM SM
MTP IEC 61754-7 TIA/EIA-604-5 Aqua/ Erika Violet Green Black (Base 8)Blue (Base12)
Black (Base 8)Blue (Base12)
Because we continuously improve our products, Siemon reserves the right to change specifications and availability without prior notice.
Worldwide Headquarters North AmericaWatertown, CT USA
Phone (1) 860 945 4200
Regional Headquarters Europe Russia AfricaChertsy, Surrey, England
Phone (44 ) 0 1932 571771
Regional Headquarters ChinaShanghai, P.R. China
Phone (86) 215385 0303
Regional Headquarters Latin America Bogota, Colombia
Phone (571) 657 1950/51/52
Regional Headquarters India Middle EastDubai, United Arab Emirates
Phone (971) 4 3689743
Siemon Interconnect SolutionsWatertown, CT USAPhone (1) 860 945 4213 US
www.siemon.com/SIS
Regional HeadquartersAsia PacificSydney, Australia
Phone (61) 2 8977 7500
SS_LightStack_I.qxp_I 4/19/18 1:56 PM Page 10