MOVEMENT. 2 Person

DESIGNED FOR. Engine Access

FALL RESTRAINT ANCHOR POINTS.Equipped

CONTROLS. Hydraulic Foot Pump

FINISH. Powder Coated Finish

Fully Extended.Ladder: 57 StrokesTilt: 23 Strokes

MOVEMENT. 2 Person

DESIGNED FOR. Engine Access

SHIPPING INFO (DIMS). 88” x 50” x

123” x 1,050 lbs

ANGLES.73 - 83 Degrees

TOWING SPEED. 10 KPH/ 6 MPH

AIRCRAFT TYPE. B767, B787, B747, A320, A310 & B717

MOVEMENT. 2 Person

DESIGNED FOR. Engine Access

CASTER DETAILS. 10” With Brakes & Swivel

HEIGHT.Low: 129 7/16” High: 183 3/8”

MATERIAL TYPE: LADDER. Aluminum

NUMBER OF USERS.1 User

MOVEMENT. 2 Person

DESIGNED FOR. Engine Access

CERTIFICATIONS. ANSI-ASC A14.7, BS EN 131.7 & CE

FOOT PRINT. 88” x 123”

MATERIAL TYPE: FRAME. Aluminum

WEIGHT CAPACITY.150 kg/330 lbs

MOVEMENT. 2 Person

DESIGNED FOR. Engine Access

Padding Material. Equipped

PART NUMBER. DF071554-07-08 # MOVEMENT.

1 Person DESIGNED FOR. Engine Access

>>

08

Tolerance Unless Noted Otherwise

THIS DRAWING AND THE INTELLECTUAL INFORMATION ON THIS DRAWING ARE THE PROPERTY OF LIFTSAFE ENGINEERING & SERVICE GROUP INC. AND MAY NOT BEREPRODUCED OR USED IN ANY MANNER WITHOUT OUR WRITTEN CONSENT

THIRD ANGLE PROJECTION

www.liftsafeinspections.com T. (519) 896-2430/1-800-977-2005, Email: info@liftsafeinspections.com F. (519) 896-2085

SIZE

Customer & Location:

Description:

LIFTSAFE ENGINEERING & SERVICE GROUP INC.

Date:

Date:

Date:

Checked By:

Drawn By:

Designed By:

Part No.

Project:

SCALE:

SHEET 1 OF 1

DWG NO: REV

AA.XXX.XX

DECIMAL PLACES

± .020± .010± .005

INCHES

± 0.3± 0.1

MILLIMETRES

± 0.5.X

Work Order No.

Materials.

Next Assembly.

ANGLE FRACTION

1/161/2°

BN.T.S

REVISION HISTORYREV DESCRIPTION DATE APPROVEDAA ISSUED FOR APPROVAL 3/7/2017 C.R.

GENERAL NOTES: 1) ALL STRUCTURAL STEEL SECTIONS SHALL CONFORM TO CSA G40.21-50W2) ALL STEEL PLATE AND BAR SHALL CONFORM TO CSA G40.21-44W3) ALL WELDING SHALL CONFORM TO CSA W59 AND BE UNDERTAKEN BY A WELDER FULLY APPROVED BY THE CANADIAN WELDING BUREAU TO CSA W47 DIVISION 4) ALL WELDS TO BE SMOOTH AND FREE OF BURRS5) ALL WELDS TO BE 1/4" CONTINUOUS FILLET OR 1/4" EFFECTIVE THROAT FLARE BEVEL U.N.O.

SIGNATURE DATE

V03121

-----

DF071554-07-08

DF071554-07-08

CR 07/03/2017

07/03/2017

07/03/2017GR

GR

87 3/4

LADDER EXTENSIONLOCATION

122 15/16

146 1/4

49 1/2

WEIGHT: 987 LBS. APPROX.

122.93

176 7/8185 5/16

87 3/4

87 3/4122 15/16

137 5/16

87 3/4 122 15/16

130 15/16

83°

83°

73°

73°

3854

[151

.73

in]

2984

[117

.5 in

]

2756

[108

.5 in

]

2688

[105

.82

in]

Technical Specifications Tolerance Unless Noted Otherwise

THIS DRAWING AND THE INTELLECTUAL INFORMATION ON THIS DRAWING ARE THE PROPERTY OF LIFTSAFE ENGINEERING & SERVICE GROUP INC. AND MAY NOT BEREPRODUCED OR USED IN ANY MANNER WITHOUT OUR WRITTEN CONSENT

THIRD ANGLE PROJECTION

www.liftsafeinspections.com T. (519) 896-2430/1-800-977-2005, Email: info@liftsafeinspections.com F. (519) 896-2085

SIZE

Customer & Location:

Description:

LIFTSAFE ENGINEERING & SERVICE GROUP INC.

Date:

Date:

Date:

Checked By:

Drawn By:

Designed By:

Part No.

Project:

SCALE:

SHEET 1 OF 1

DWG NO: REV

AA.XXX.XX

DECIMAL PLACES

± .020± .010± .005

INCHES

± 0.3± 0.1

MILLIMETRES

± 0.5.X

Work Order No.

Materials.

Next Assembly.

ANGLE FRACTION

1/161/2°

BN.T.S

REVISION HISTORYREV DESCRIPTION DATE APPROVEDAA ISSUED FOR APPROVAL 3/7/2017 C.R.

GENERAL NOTES: 1) ALL STRUCTURAL STEEL SECTIONS SHALL CONFORM TO CSA G40.21-50W2) ALL STEEL PLATE AND BAR SHALL CONFORM TO CSA G40.21-44W3) ALL WELDING SHALL CONFORM TO CSA W59 AND BE UNDERTAKEN BY A WELDER FULLY APPROVED BY THE CANADIAN WELDING BUREAU TO CSA W47 DIVISION 4) ALL WELDS TO BE SMOOTH AND FREE OF BURRS5) ALL WELDS TO BE 1/4" CONTINUOUS FILLET OR 1/4" EFFECTIVE THROAT FLARE BEVEL U.N.O.

SIGNATURE DATE

V03121

-----

DF071554-07-08

DF071554-07-08

CR 07/03/2017

07/03/2017

07/03/2017GR

GR

87 3/4

LADDER EXTENSIONLOCATION

122 15/16

146 1/4

49 1/2

WEIGHT: 987 LBS. APPROX.

122.93

176 7/8185 5/16

87 3/4

87 3/4122 15/16

137 5/16

87 3/4 122 15/16

130 15/16

83°

83°

73°

73°

3854

[151

.73

in]

2984

[117

.5 in

]

2756

[108

.5 in

]

2688

[105

.82

in]

Aircraft Maintenance and Engine Access Stand 07-08

ACCESSORY PART NUMBER DESCRIPTION

Platform Adaptor DF071554-Platform-Adaptor Plugin platform in place of the curved section on all current engine stands.

Air Powered Pump DF-Stand-Air-Pump Optional air pump instead of the manual hydraulic pump system.

Fork Pockets DF071554-07-Fork-Pockets These fork pocket additions will enable you to quickly and easily move your stand.

Accessories

Jacks DF071554-07-Leveling-Jacks This set of 4 leveling jacks and attachment plates will allow you to secure your stand.

Tow Bar DF071554-07-Tow-Bar Quickly and efficiently move your stand with the addition of a tow bar attachment.

Utilities Package DF-Stand-Utilities-Package Adds shop air and electrical power user service package to a unit.

fallsafetysolutions.com| 09

This Aircraft Maintenance Stand is for the under and over cowling access requirements of the B767 and B787. As with all our stands, we use anti-fatigue ladder rungs rather than narrow ladder rungs. This ensures comfort when using the stands to change LRU’S, adjust components or connect/disconnect engines and nacelles. Functionality improves as a result of a lighter design, smaller footprint and greater geometry. This product is currently in use at multiple operators, MRO’S and aircraft manufacturers.

The stand facilitates safe access to nose cowls, fan cowls and pylon disconnect zones on PW, GE and RR engines, providing a safe working solution to many of the traditionally difficult under-cowling maintenance locations. The unit is also designed to safely access the same points outside of cowling, specifically forward and aft pylon service points, as well as hard to reach refuel panels and under-wing areas. The hydraulic pitch and height adjustment allow for the diverse angles and height requirements frequently used when servicing aircraft. The stand contains extensive aluminum construction for easy movement and corrosion-resistant powder coat finish for longevity. For increased safety and ease of mobility, the stand has optional accessories which can be added. They include 4 corner-leveling jacks, fold away tow bars and lift truck fork pockets. The stand is designed and tested in accordance with ANSI-ASC A14.7 and BS EN 131.7 and includes CE Certification.

Stand Description

DF071554-07-08