Embed Size (px)
Citation preview
DESIGNED FOR. Engine Access
FOOT PRINT. 89 11/16” x 163 3/16”
CONTROLS. Hydraulic Foot Pump
NUMBER OF USERS. 1 User
AIRCRAFT TYPE. B747, A380, A340, A400
WEIGHT CAPACITY.150 kg/330 lbs
MATERIAL TYPE: LADDER. Aluminum
Padding Material. Equipped
SHIPPING INFO (DIMS). 89 11/16”x 64 1/2” x 163 3/16” x 2,400 lbs
CASTER DETAILS. 10” With Brakes & Swivel
CERTIFICATIONS. ANSI-ASC A14.7, BS EN 131.7 & CE
FALL RESTRAINT ANCHOR POINTS.Equipped
Tolerance Unless Noted Otherwise
THIS DRAWING AND THE INTELLECTUAL INFORMATION ON THIS DRAWING ARE THE PROPERTY OF LIFTSAFE ENGINEERING & SERVICE GROUP INC. AND MAY NOT BEREPRODUCED OR USED IN ANY MANNER WITHOUT OUR WRITTEN CONSENT
THIRD ANGLE PROJECTION
www.liftsafeinspections.com T. (519) 896-2430/1-800-977-2005,Email: [email protected] F. (519) 896-2085
SIZE
Customer & Location:
Description:
LIFTSAFE ENGINEERING & SERVICE GROUP INC.
Date:
Date:
Date:
Checked By:
Drawn By:
Designed By:
Part No.
Project:
SCALE:
SHEET 1 OF 1
DWG NO: REV
6.1.XXX
.XX
DECIMAL PLACES
± .020± .010± .005
INCHES
± 0.3± 0.1
MILLIMETRES
± 0.5.X
Work Order No.
Materials.
Next Assembly.
ANGLE FRACTION
1/161/2°
BN.T.S
REVISION HISTORYREV DESCRIPTION DATE APPROVED6.1 ISSUED FOR PRODUCTION 1/21/2016 C.R.
GENERAL NOTES:
1) ALL STRUCTURAL STEEL SECTIONS SHALL CONFORM TO CSA G40.21-50W2) ALL STEEL PLATE AND BAR SHALL CONFORM TO CSA G40.21-44W3) ALL WELDING SHALL CONFORM TO CSA W59 AND BE UNDERTAKEN BY A
WELDER FULLY APPROVED BY THE CANADIAN WELDING BUREAU TO CSA W47 DIVISION
4) ALL WELDS TO BE SMOOTH AND FREE OF BURRS5) ALL WELDS TO BE 1/4" CONTINUOUS FILLET OR 1/4" EFFECTIVE THROAT FLARE
BEVEL U.N.O.
SIGNATURE DATE
V00026
-----
DF071554-06
ENG. ACCESS WITH SCISSOR
97 1/8
130
19 7/8
239 1/4
154 5/16
73°
83°
CR 1/21/2016
1/21/2016
1/21/2016GR
GR
STAND @ 73° LADDER RETRACTEDSTAND @ 83° LADDER RETRACTED
STAND @ 83° LADDER EXTENDED
STAND @ 73° LADDER EXTENDED
246 1/2
213 1/16
0
71 3/8
0
15 7/8
98 7/8
136 1/8143 3/8
109 15/16
83°
0
15 7/8
97 3/8107 3/16
126 1/2
139 1/16
0
71 3/8
152 7/8
231 3/8240 1/2
208 9/16
67 3/4
73°
PART NUMBER. DF071554-06
HEIGHT.Low: 126 1/2”High: 239 1/4”
ANGLES.73 - 83 Degrees
06
# MOVEMENT. 2 Person
Aircraft Maintenance and Engine Access Stand 06
Fully Extended.Ladder: 128 StrokesTilt: 43 Strokes Scissors: 86 Strokes >>
FINISH. Powder Coated Finish
MATERIAL TYPE: FRAME. Steel
Technical Specifications
TOWING SPEED. 10 KPH/ 6 MPH
DESIGNED FOR. Engine Access
Padding Material. Equipped
SHIPPING INFO (DIMS). 89 11/16”x 64 1/2” x 163 3/16” x 2,400 lbs
CERTIFICATIONS. ANSI-ASC A14.7, BS EN 131.7 & CE
FALL RESTRAINT ANCHOR POINTS.Equipped
DF071554-06
This stand is designed with an adjustable scissor lift base to give it the height required to access the outboard engines on the A380, B747, A340 series, A400 etc. As with all our stands, we use anti-fatigue ladder rungs rather than narrow ladder rungs. This ensures comfort when using the stands to change LRU’S, adjust components, or connect/disconnect engines and nacelles. Functionality improvements include outboard engines and pylon access (A380, A340 and B747-8) as well as avionics and aft-fuselage access points. Currently in use at multiple operators, MRO’S and aircraft manufacturers, this unit has flexibility for use on all Boeing wide body aircraft in addition to the B757. The dynamic design also allows for full use on Airbus wide body aircraft as well as the A320 family.
The stand facilitates safe access to nose cowls, fan cowls and pylon disconnect zones on PW, GE and RR engines, providing a safe working solution to many of the traditionally difficult under-cowling maintenance locations. The unit is also designed to safely access the same points outside of cowling, specifically forward and aft pylon service points, as well as hard to reach refuel panels and under-wing areas. The hydraulic pitch and height adjustment allow for the diverse angles and height variables frequently required when servicing aircraft. The stand contains extensive aluminum construction for easy movement and corrosion-resistant powder coat finish for longevity. For increased safety and ease of mobility, the stand comes equipped with 4 corner-leveling jacks, fold away tow bars and lift truck fork pockets. The stand is designed and tested in accordance with ANSI-ASC A14.7 and BS EN 131.7 and includes CE Certification.
fallsafetysolutions.com| 07
ACCESSORY PART NUMBER DESCRIPTION
Utilities Package DF-Stand-Utilities-Package Adds shop air and electrical power user service package to a unit.
Air Powered Pump DF-Stand-Air-Pump Optional air pump instead of the manual hydraulic pump system.
Stand Description
Extension DF071554-Extension-.25M Extension in place of upper curve, .25m longer than existing curve.
Accessories
Aircraft Maintenance and Engine Access Stand 06
