Technical dataHydraulic crawler crane

HS 8030 HD

2 HS 8030 HD

DimensionsBasic machine with undercarriage

50004140

2070110

1060

1590

5150

2110

970

R 3560

9500

4150

6003700

250

890

2480

Operating weightThe operating weight includes the basic machine with telescopic undercarriage, 2 main winches 100 kN each, including wire ropes (1x 90 m / 1x 70 m) and 10 m main boom, consisting of boom foot (6.0 m), boom head (3.5 m) and hinged section (0.5 m), 5.9 t basic counterweight, 600 mm 3-web grousers and 30 t hook block. Total weight approx. 34.7 t

Ground pressureGround bearing pressure 0.69 kg/cm2

EquipmentMain boom (No. 0808.xx) max. length 22 m Fixed jib (No. 0403.xx) upon request Modular designed equipment for crane or clamshell operation.

Remarks1. The lifting capacities stated are valid for lifting operation only

(corresponding with crane classication according to F.E.M. 1.001, crane group A1).

2. Crane standing on rm, horizontal ground.

3. The weight of the lifting device (hoist ropes, hook block, shackle etc.) must be deducted from the gross lifting capacity to obtain a net lifting value.

4. Additional equipment on boom (e.g. boom walkways, auxiliary jib) must be deducted to get the net lifting capacity.

5. For max. wind speed please refer to lift chart in operators cab or manual.

6. Working radii are measured from center of swing and under load.

7. The lifting capacities are valid for 360 degrees of swing.

8. Calculation of stability under load is based on ISO 4305 Table 1 + 2, tipping angle 4.

9. The structures are calculated according to F.E.M. 1.001 - 1998 (EN 13001-2 / 2004).

HS 8030 HD 3

Transport dimensions and weightsBasic machine and boom (No. 0808.xx)

Dimensions and weightsWeight complete with counterweight 36.3 t

10300 5000 1060600

2500

2480

250

3410

16825

34203000 3000

4300 5000 1060600

2500

2480

250

3410

10825

3420

Transport - with 10 m main boomincludes the basic machine (ready for operation) with boom foot (6 m), boom head (3.5 m), hinged section (0.5 m), hook block (30 t) and counterweight (5.9 t).

Transport - with 16 m main boomincludes the basic machine (ready for operation) with boom foot (6 m), boom head (3.5 m), hinged section (0.5 m), 2x boom section (3 m), hook block (30 t) and counterweight (5.9 t).

Transport - with 22 m main boomincludes the basic machine (ready for operation) with boom foot (6 m), boom head (3.5 m), hinged section (0.5 m), 4x boom section (3 m), hook block (30 t) and counterweight (5.9 t).

Dimensions and weightsWeight complete with counterweight 34.7 t

Dimensions and weightsWeight complete with counterweight 35.5 t

10000 5000 1060600

2500

2480

250

3410

13825

34203000

4 HS 8030 HD

Transport dimensions and weights Boom section

3185

985

Boom section (No. 0808.xx) 3 mWidth 930 mm

Weight 395 kg

Hooks

350

1000

700

1400

30 t hook block 1 sheaveWidth 250 mm

Weight 400 kg

10 t single hookWidth 350 mm

Weight 330 kg

HS 8030 HD 5

Technical description HS 8030 HD

EnginePower rating according to ISO 9249, 180 kW (241 hp) at 2000 rpm Engine type Liebherr D 934 A7 SCR Fuel tank 470 l capacity with continuous level indicator and reserve warningEngine complies with NRMM exhaust certication EPA/CARB Tier 4i or 97/68 EC Stage III B. ECO-Silent-Mode:For work not requiring high engine power, the diesel engine can be operated in the ECO-Silent-Mode (e.g. for inserting reinforcement cages or for lift crane operation). Due to the ECO-Silent-Mode which can be preselected by the operator the engine runs with optimum fuel efciency. This lowers consumption and reduces noise emission.

Main winchesWinch options:Line pull (nom. load) 100 kNRope diameter 24 mmRope speed 0-130 m/minThe winches are outstanding in their compact design and easy assembly. Clutch and braking functions on the free-fall system are provided by a compact designed, low wear and maintenance-free multidisc brake. The drag and hoist winches use pressure controlled, variable ow hydraulic motors. This system features sensors that automatically adjust oil ow to provide max. winch speed depending on load. Option:Tagline winch 20 kN with free fall

CrawlersThe track width of the undercarriage is changed hydraulically.Propulsion through axial piston motor, hydraulically released spring loaded multidisc brake, maintenance-free crawler tracks, hydraulic chain tensioning device. Drive speed 0 1.8 km/h Track force 459 kN3-web grousers 600 mm Transport width 2500 mm

ControlThe core of the Liebherr hydraulic crawler cranes is the Litronic control system. Developed and manufactured by Liebherr, this comprehensive system encompasses all control and monitoring functions and is designed to withstand extreme temperature changes and the rough heavy duty tasks common in the construction industry. Complete machine operating data, warnings and failure indications are clearly displayed in the required language on the high resolution monitor in the operators cab.Documentation of operating data (PDE) enables optimum diagnosis as well as early detection and prevention of more serious defects.An electro-hydraulic proportional control allows several movements to be performed simultaneously. This ensures that all categories of loads can be positioned with utmost precision.Options: s 0$%0ROCESSDATARECORDING s '3-'023TELEMATICSMODULE

Noise emissionNoise emissions correspond with 2000/14/EC directive on noise emission by equipment used outdoors.

Hydraulic systemA double axial displacement pump with integrated gearbox supplies the open loop hydraulic system, allowing all functions to be operated simultaneously. To minimize peak pressure an automatic working pressure cutoff is integrated. This spares pumps and saves energy.The hydraulic oil is cleaned through electronically controlled pressure and return lters. Possible contamination is signalled in the cabin.The use of synthetic environmentally friendly (biodegradable) oils is possible.Ready made hydraulic retrot kits are available to customize requirements e. g. powering casing oscillators, hydraulic grabs etc.

Pumps for working tools 2x 239 l/minOil tank capacity 500 l Working pressure max. 350 bar

SwingConsists of roller bearing with internal teeth for lower tooth ank pressure, xed axial piston hydraulic motor, spring loaded and hydraulically released multidisc holding brake, planetary gearbox and pinion. Swing speed from 0 3.5 rpm continuously variable.

Boom lufngDouble-acting cylinderMax. stroke (from 0- 84) 2050 mmBoom lufng speed from 15 to 84 23 sec.Boom angle 0 = transport positionFor boom assembly the boom foot can be lowered to -15.5.

6 HS 8030 HD

Equipment (Main boom No. 0808.xx and 5.9 t counterweight) Slurry wall grab and clamshell

Slurry wall grabWinch options 2 x 100 kN Line speed 1st layer 0130 m/min Max. chisel weight 6 t

ClamshellWinch options 2 x 100 kN Line speed 1st layer 0130 m/min

HS 8030 HD 7

Casing oscillatorWinch options 2 x 100 kN Line speed 1st layer 0130 m/min Max. drilling diameter 1000 mm

Equipment (Main boom No. 0808.xx and 5.9 t counterweight) Casing oscillator

8 HS 8030 HD

Above load chart is for reference only. For actual lift duty please refer to load chart in operators cab or manual.

Capacities in metric tonnes for boom lengths (10 m - 22 m) - with 100 kN winches

Boom length (m)

Radius 10 13 16 19 22

(m) t t t t t

2 14.9 14.9 14.9

3 14.0 14.9 13.2 12.7 11.3

4 12.0 11.3 10.1 9.5 8.4

5 9.1 8.5 8.1 7.6 6.8

6 7.4 7.1 6.7 6.3 5.7

7 6.3 6.0 5.7 5.3 4.8

8 5.5 5.2 4.9 4.6 4.2

9 4.8 4.5 4.3 4.0 3.7

10 3.9 3.8 3.5 3.2

Maximum capacity in duty cycle operation with standard ropes

Line pull kN 100

Rope diameter mm 24

Minimum breaking load kN 355

Line pull - 1-rope duty cycle operation t 10

Line pull - 2-rope duty cycle operation 1) t 15.2

1) Lifting a load exceeding the line pull of one winch is only allowed if it can be ensured that each individual winch is not overloaded. When working with a mechanical 2-rope grab the total load to be lifted is limited by the line pull of one winch. Rigging and ropes are part of the load.

2) Max. capacities in metric tonnes do not exceed 75% of tipping load. Crane standing on rm, horizontal ground.

Capacities in duty cycle operation are for reference only and are not programmed in the LMI system. All loads and counterweight congurations are max. values and must not be exceeded.Weight of additional equipment on boom (e.g. walkways, hose drums etc.) must be deducted to get the net capacity.

Load chart for duty cycle operation (Main boom No. 0808.xx) 5.9 t counterweight

HS 8030 HD 9

Clamshell equipment (Main boom No. 0808.xx) 5.9 t counterweight

J

1500

K

C

Max. capacities in metric tonnes do not exceed 66.7% of tipping load. Capacities in duty cycle operation are for reference only and are not programmed in the LMI system. Working diagram

C = Radius / dumping radius J = Height of boom head sheave centre above ground level K = Length of clamshell (according to manufacturers specication)

Capacities in metric tonnes for boom lengths (10 m - 22 m) counterweight 5.9 t

Boom length (m)10 13 16 19 22

alpha C J C J C J C J C J

(m) (m) (t) (m) (m) (t) (m) (m) (t) (m) (m) (t) (m) (m) (t)

65 4.4 11.0 10.5 5.7 13.8 7.4 7.0 16.5 5.7 8.2 19.2 4.4 9.5 21.9 3.4

60 5.2 10.6 8.6 6.7 13.2 6.3 8.2 15.8 4.8 9.7 18.4 3.6 11.2 21.0 2.4

55 6.0 10.2 7.5 7.7 12.6 5.4 9.4 15.1 4.1 11.1 17.5 2.6

50 6.6 9.6 6.6 8.6 11.9 4.8 10.5 14.2 3.3

45 7.3 9.1 6.0 9.4 11.2 4.3 11.5 13.3 2.2

40 7.9 8.4 5.6 10.2 10.3 3.7

35 8.4 7.7 5.2 10.9 9.4 2.8

30 8.9 7.0 4.9 11.5 8.5 2.2

25 9.3 6.2 4.6

10 HS 8030 HD

0 m12345678910111213141516171819202122

0 ft510152025303540455055606570

70

8480

60

50

40

30

10 m

13 m

16 m

00

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

5

15

20

25

30

35

40

45

50

55

60

65

70

75

80

85

10

22 m

19 m

Main boom (No. 0808.xx) 84 305.9 t counterweight

Main boom conguration (No. 0808.xx)Conguration for boom lengths (10 m - 22 m)

Length Amount of boom extensions

Boom foot 6.0 m 1 1 1 1 1

Hinged section 0.5 m 1 1 1 1 1

Boom section 3.0 m 1 2 3 4

Boom head 3.5 m 1 1 1 1 1

Boom length (m) 10 13 16 19 22

HS 8030 HD 11

Load chart for lift crane operation (Main boom No. 0808.xx) 5.9 t counterweight

Above load chart is for reference only. For actual lift duty please refer to load chart in operators cab or manual.

Capacities in metric tonnes for boom lengths (10 m - 22 m) - with 100 kN winches

Boom length (m)

Radius 10 13 16 19 22

(m) t t t t t

2 29.4 29.3 29.1 29.0

3 28.5 28.5 24.2 22.0 19.6

4 22.3 20.9 19.4 17.1 15.6

5 16.4 15.6 14.9 14.1 12.8

6 12.5 12.3 11.8 11.3 10.8

7 9.7 9.9 9.7 9.3 8.9

8 7.8 8.0 8.1 7.8 7.5

9 6.4 6.6 6.7 6.6 6.3

10 5.5 5.6 5.6 5.5

12 4.0 4.1 4.1 4.1

14 3.0 3.0 3.0

16 2.3 2.2TLT 10579752 M99999 Vorab1

Liebherr-Werk Nenzing GmbH Dr. Hans Liebherr Str. 1, 6710 Nenzing/Austria Tel.: +43 50809 41473, Fax: +43 50809 41499 crawler.crane@liebherr.com, www.liebherr.com facebook.com/LiebherrConstruction

HS

80

30 H

D

1122

3967

05

/201

4 S

ubje

ct t

o ch

ang

e w

itho

ut n

otic

e.