Upload
boroda2410
View
133
Download
14
Tags:
Embed Size (px)
Citation preview
North/Latin America http://aic.lgservice.comEurope/Africa http://eic.lgservice.comAsia/Oceania http://biz.lgservice.com
Internal Use Only
Printed in KoreaP/NO :
CHASSIS :
MODEL :
CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SERVICE MANUAL
MFL67714406 (1307-REV00)
27MS73S 27MS73S-PZ(R)Q27MS73V 27MS73V-PZQ
LD33A
LED TV
- 2 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
CONTENTS
CONTENTS .............................................................................................. 2
SAFETY PRECAUTIONS ......................................................................... 3
SERVICING PRECAUTIONS .................................................................... 4
SPECIFICATION ....................................................................................... 6
ADJUSTMENT INSTRUCTION .............................................................. 15
BACKCOVER DISASSEMBLE GUIDE .................................................. 21
TROUBLE SHOOTING ........................................................................... 22
BLOCK DIAGRAM .................................................................................. 29
EXPLODED VIEW .................................................................................. 30
SCHEMATIC CIRCUIT DIAGRAM ..............................................................
- 3 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.
It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.
Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1M and 5.2M. When the exposed metal has no return path to the chassis the reading must be infinite.An other abnormality exists that must be corrected before the receiver is returned to the customer.
Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts.Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA.In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.
Leakage Current Hot Check circuit
1.5 Kohm/10W
0.15FTo Instrument'sexposed METALLIC PARTS
Good Earth Groundsuch as WATER PIPE,CONDUIT etc.
AC Volt-meter
When 25A is impressed between Earth and 2nd Groundfor 1 second, Resistance must be less than 0.1*Base on Adjustment standard
IMPORTANT SAFETY NOTICE
SAFETY PRECAUTIONS
- 4 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication.NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First.
General Servicing Precautions1. Always unplug the receiver AC power cord from the AC power
source before;a. Removing or reinstalling any component, circuit board
module or any other receiver assembly.b. Disconnecting or reconnecting any receiver electrical plug or
other electrical connection.c. Connecting a test substitute in parallel with an electrolytic
capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity
installation of electrolytic capacitors may result in an explosion hazard.
2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe.
Do not test high voltage by "drawing an arc".3. Do not spray chemicals on or near this receiver or any of its
assemblies.4. Unless specified otherwise in this service manual, clean
electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength)
CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of
contacts in not required.5. Do not defeat any plug/socket B+ voltage interlocks with which
receivers covered by this service manual might be equipped.6. Do not apply AC power to this instrument and/or any of its
electrical assemblies unless all solid-state device heat sinks are correctly installed.
7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead.
Always remove the test receiver ground lead last.8. Use with this receiver only the test fixtures specified in this
service manual. CAUTION: Do not connect the test fixture ground strap to any
heat sink in this receiver.
Electrostatically Sensitive (ES) DevicesSome semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity.1. Immediately before handling any semiconductor component or
semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the
unit under test.2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.
CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.)
General Soldering Guidelines1. Use a grounded-tip, low-wattage soldering iron and appropriate
tip size and shape that will maintain tip temperature within the range or 500 F to 600 F.
2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.
3. Keep the soldering iron tip clean and well tinned.4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
bristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners.5. Use the following unsoldering technique
a. Allow the soldering iron tip to reach normal temperature. (500 F to 600 F)b. Heat the component lead until the solder melts.c. Quickly draw the melted solder with an anti-static, suction-
type solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuit
board printed foil.6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature (500 F to 600 F)
b. First, hold the soldering iron tip and solder the strand against the component lead until the solder melts.
c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil.
CAUTION: Work quickly to avoid overheating the circuit board printed foil.
d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.
SERVICING PRECAUTIONS
- 5 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
IC Remove/ReplacementSome chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.
Removal1. Desolder and straighten each IC lead in one operation by gently
prying up on the lead with the soldering iron tip as the solder melts.
2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.
Replacement1. Carefully insert the replacement IC in the circuit board.2. Carefully bend each IC lead against the circuit foil pad and
solder it.3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).
"Small-Signal" Discrete TransistorRemoval/Replacement1. Remove the defective transistor by clipping its leads as close as
possible to the component body.2. Bend into a "U" shape the end of each of three leads remaining
on the circuit board.3. Bend into a "U" shape the replacement transistor leads.4. Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.
Power Output, Transistor DeviceRemoval/Replacement1. Heat and remove all solder from around the transistor leads.2. Remove the heat sink mounting screw (if so equipped).3. Carefully remove the transistor from the heat sink of the circuit
board.4. Insert new transistor in the circuit board.5. Solder each transistor lead, and clip off excess lead.6. Replace heat sink.
Diode Removal/Replacement1. Remove defective diode by clipping its leads as close as
possible to diode body.2. Bend the two remaining leads perpendicular y to the circuit
board.3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.4. Securely crimp each connection and solder it.5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.
Fuse and Conventional ResistorRemoval/Replacement1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.2. Securely crimp the leads of replacement component around
notch at stake top.3. Solder the connections.
CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.
Circuit Board Foil RepairExcessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.
At IC ConnectionsTo repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections).
1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).
2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.
4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.
At Other ConnectionsUse the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.
1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.2. Trace along the copper pattern from both sides of the pattern
break and locate the nearest component that is directly connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side.
Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the
it does not touch components or sharp edges.
- 6 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
SPECIFICATION
1. Application Range This spec sheet is applied all of the TV used LD33A chassis.
2. SpecificationEach part is tested as below without special appointment
1) Temperature : 25 C 5 C (77 F 9 F), CST : 40 C 5 C2) Relative Humidity : 65 % 10 % 3) Power Voltage : Standard input voltage (100 V - 240 V ~, 50 / 60 Hz) Standard Voltage of each products is marked by models 4) Specification and performance of each parts are followed
each drawing and specification by part number in accord-ance with BOM.
5) The receiver must be operated for about 5 minutes prior to the adjustment.
3.Test method1) Performance : LGE TV test method followed2) Demanded other specification - Safety : CE,IEC specification - EMC : CE,IEC specification
NOTE : Specifications and others are subject to change without notice for improvement.
- 7 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
4. General specification4.1. TV
No Item Specification Remarks
1 Market EU/CIS (PAL Market-37 Countries) DTV & Analog (Total 37 countries)DTV (MPEG2/4, DVB-T) : 30 countriesGermany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ire-land, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Beralus
DTV (MPEG2/4, DVB-T2) : 7 countriesUK(Ireland), Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan
DTV (MPEG2/4, DVB-C) : 37 countriesGermany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ire-land, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Beralus, UK, Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan
DTV (MPEG2/4,DVB-S) : 30 countriesGermany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ire-land, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Beralus
Supported satellite : 22 satellitesHISPASAT 1C/1D, ATLANTIC BIRD 2, NILESAT 101/102, ATLANTIC BIRD 3, AMOS 2/3, THOR 5/6, IRIUS 4, EU-TELSAT-W3A, EUROBIRD 9, EUTELSAT-W2A, HOTBIRD 6/8/9, EUTELSAT-SESAT, ASTRA 1L/H/M/KR, ASTRA 3/3B, BADR 4/6, ASTRA 2D, EUROBIRD 3, EUTELSAT-W7, HEL-LASSAT 2, EXPRESS AM1, TURKSAT 2/3, INTERSAT10
2 Broadcasting system
1) PAL-BG2) PAL-DK3) PAL-I/I4) SECAM L/L, DK, BG, I5) DVB-T6) DVB-C7) DVB-T28) DVB-S/S2
DVB-S: Satellite
- 8 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
No Item Specification Remarks
3 Receiving system Analog : Upper HeterodyneDigital : COFDM, QAM
DVB-T- Guard Interval(Bitrate_Mbit/s)1/4, 1/8, 1/16, 1/32- Modulation : Code RateQPSK: 1/2, 2/3, 3/4, 5/6, 7/816-QAM: 1/2, 2/3, 3/4, 5/6, 7/864-QAM: 1/2, 2/3, 3/4, 5/6, 7/8
DVB-T2- Guard Interval(Bitrate_Mbit/s)1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256,- Modulation : Code RateQPSK: 1/2, 2/5, 2/3, 3/4, 5/616-QAM: 1/2, 2/5, 2/3, 3/4, 5/664-QAM: 1/2, 2/5, 2/3, 3/4, 5/6256-QAM: 1/2, 2/5, 2/3, 3/4, 5/6
DVB-C- Symbolrate: 4.0Msymbols/s to 7.2Msymbols/s- Modulation: 16QAM, 64-QAM, 128-QAM and 256-QAM
DVB-S/S2- symbolrateDVB-S2 (8PSK / QPSK): 2 ~ 45Msymbol/sDVB-S (QPSK): 2 ~ 45Msymbol/s- viterbiDVB-S mode: 1/2, 2/3, 3/4, 5/6, 7/8DVB-S2 mode: 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10
4 Scart Jack (1EA) PAL, SECAM Scart jack is Full scart and support ATV/DTV-OUT(not support DTV Auto AV)
5 Video Input RCA(1EA) PAL, SECAM, NTSC4.43 4 System :PAL, SECAM, NTSC4.43, PAL60Phone jack type
6 Head phone out Antenna, AV1, AV2, Component, HDMI1, HDMI2, USB1, USB2, USB3
7 Component Input (1EA) Y/Cb/CrY/Pb/Pr
Phone jack type
8 HDMI Input (2EA) HDMI1-DTVHDMI2-DTV
Support HDMI-PC mode (HDMI1/2) - INPUT LABEL : PCHDMI1 : MHL / HDMI2 : ARC
9 Audio Input (3EA) PC AudioComponent/AV2AV1
L/R Input
10 USB (3EA) EMF, DivX HD, For SVC (download) ,HDD,HUB
JPEG, MP3, DivX HD
11 Ethernet Connect(1EA) Ethernet Connect
5. USB InputNo Item Min Typ Max Unit Remark
1 USB input Vcc 4.75 5.0 5.25 V Stick type (~ 700mA)Hard disk type (3.5inch, ~1A)
Current consumption 0.4 1.5 A
- 9 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
6. Component Video Input (Y, Cb/Pb, Cr/Pr)No. Resolution H-freq(kHz) V-freq(Hz) Porposed
1 720 x 480 15.73 60.00 SDTV, DVD 480i
2 720 x 480 15.63 59.94 SDTV, DVD 480i
3 720 x 480 31.47 59.94 480p
4 720 x 480 31.50 60.00 480p
5 720 x 576 15.625 50.00 SDTV, DVD 625 Line
6 720 x 576 31.25 50.00 HDTV 576p
7 1280 x 720 45.00 50.00 HDTV 720p
8 1280 x 720 44.96 59.94 HDTV 720p
9 1280 x 720 45.00 60.00 HDTV 720p
10 1920 x 1080 31.25 50.00 HDTV 1080i
11 1920 x 1080 33.75 60.00 HDTV 1080i
12 1920 x 1080 33.72 59.94 HDTV 1080i
13 1920 x 1080 56.250 50 HDTV 1080p
14 1920 x 1080 67.5 60 HDTV 1080p
No. Resolution H-freq(kHz) V-freq.(kHz) Proposed
1 640 x 480 31.469 / 31.5 59.94/60 SDTV 480P
2 720 x 480 31.469 / 31.5 59.94 / 60 SDTV 480P
3 720 x 576 31.25 50 SDTV 576P
4 720 x 576 15.625 50 SDTV 576I
5 1280 x 720 37.500 50 HDTV 720P
6 1280 x 720 44.96 / 45 59.94 / 60 HDTV 720P
7 1920 x 1080 33.72 / 33.75 59.94 / 60 HDTV 1080I
8 1920 x 1080 28.125 50.00 HDTV 1080I
9 1920 x 1080 26.97 23.97 HDTV 1080P
10 1920 x 1080 27 24 HDTV 1080P
11 1920 x 1080 33.716 / 33.75 29.976 / 30.00 HDTV 1080P
12 1920 x 1080 56.250 50 HDTV 1080P
13 1920 x 1080 67.43 / 67.5 59.94 / 60 HDTV 1080P
No. Resolution H-freq(kHz) V-freq.(Hz) Proposed
1 640 x 350 @70Hz 31.468 70.09 EGA
2 720 x 400 @70Hz 31.469 70.08 DOS
3 640 x 480 @60Hz 31.469 59.94 VESA(VGA)
4 800 x 600 @60Hz 37.879 60.31 VESA(SVGA)
5 1024 x 768 @60Hz 48.363 60.00 VESA(XGA)
6 1152 x 864 @60Hz 54.348 60.053 VESA
7 1280 x 1024 @60Hz 63.981 60.020 VESA(SXGA)
8 1360 x 768 @60Hz 47.712 60.015 VESA(WXGA)
9 1920 x 1080 @60Hz 67.5 60.00 WUXGA(Reduced Blanking))
7.2. PC mode
7.1. HDMI (DTV)7. HDMI input
- 10 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
ADJUSTMENT INSTRUCTION1. Application Range
This specification sheet is applied to all of the TV with LD33A chassis.
2. Specification1) Because this is not a hot chassis, it is not necessary to
use an isolation transformer. However, the use of isolation transformer will help protect test instrument.
2) Adjustment must be done in the correct order. 3) The adjustment must be performed in the circumstance of
25 C 5 C of temperature and 65 % 10 % of relative humidity if there is no specific designation.
4) The input voltage of the receiver must keep AC 100-240 V~, 50/60 Hz.
5) The receiver must be operated for about 5 minutes prior to the adjustment when module is in the circumstance of over 15.
In case of keeping module is in the circumstance of 0 C, it should be placed in the circumstance of above 15 C for 2 hours.
In case of keeping module is in the circumstance of below -20 C, it should be placed in the circumstance of above 15 C for 3 hours.
[Caution] When still image is displayed for a period of 20 minutes or longer (Especially where W/B scale is strong. Digital pattern 13ch and/or Cross hatch pattern 09ch), there can some after-image in the black level area.
3. Automatic Adjustment3.1. MAC address D/L , CI+ key D/L , Wide-
vine key D/L, ESN D/LConnect: USB portCommunication Prot connection Com 1,2,3,4 and 115200(Baudrate) Mode check: Online Only Check the test process: DETECT MAC CI Widevine
ESN Play: START Result: Ready, Test, OK or NG Printer Out (MAC Address Label)
3.2. LAN Inspection3.2.1. Equipment & Condition
Each other connection to LAN Port of IP Hub and Jig
3.2.2. LAN inspection solution LAN Port connection with PCB Setting automatic IP
If you want manual connection, enter Network connection at MENU Mode of TV. Press Start connection key, then Net-work will be connected.
Setting state confirmation If automatic setting is finished, you confirm IP and MAC
Address.
3.2.3. WIDEVINE key Inspection- Confirm key input data at the "IN START" MENU Mode.
- 11 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
3.3. LAN PORT INSPECTION(PING TEST)Connect SET LAN port == PC LAN Port
3.3.1. Equipment setting1) Play the LAN Port Test PROGRAM.2) Input IP set up for an inspection to Test Program.*IP Number : 12.12.2.2
3.3.2. LAN PORT inspection(PING TEST)1) Play the LAN Port Test Program.2) Connect each other LAN Port Jack.3) Play Test (F9) button and confirm OK Message.4) Remove LAN cable.
3.4. Model name & Serial number Down-load
3.4.1. Model name & Serial number D/L Press Power on key of service remocon.(Baud rate :
115200 bps) Connect RS-232C Signal to USB Cable to USB. Write Serial number by use USB port. Must check the serial number at Instart menu.
3.4.2. Method & notice1) Serial number D/L is using of scan equipment.2) Setting of scan equipment operated by Manufacturing
Technology Group.3) Serial number D/L must be conformed when it is produced
in production line, because serial number D/L is mandatory by D-book 4.0.
* Manual Download (Model Name and Serial Number)
If the TV set is downloaded by OTA or service man, sometimes model name or serial number is initialized.(Not always)It is impossible to download by bar code scan, so It need Manual download.1) Press the "Instart" key of Adjustment remote control.2) Go to the menu "Model Number D/L" like below photo.3) Input the Factory model name(ex 27MS73V-PZ) or Serial
number like photo.4) Check the model name Instart menu. Factory name
displayed. (ex 27MS73S/V-PZQ)5) Check the Diagnostics.(DTV country only) Buyer model
displayed. (ex 27MS73S/V-PZ)
3.5. CI+ Key checking method- Check the Section 4.2Check whether the key was downloaded or not at In Start menu. (Refer to below).
=> Check the Download to CI+ Key value in LGset.
3.5.1. Check the method of CI+ Key value(1) Check the method on Instart menu(2) Check the method of RS232C Command 1) Into the main assy mode(RS232: aa 00 00)
2) Check the key download for transmitted command (RS232: ci 00 10)
3) Result value - Normally status for download : OKx - Abnormally status for download : NGx
SET PC
CMD 1 CMD 2 Data 0A A 0 0
CMD 1 CMD 2 Data 0C I 1 0
- 12 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
3.5.2. Check the method of CI+ key value(RS232) 1) Into the main assy mode(RS232: aa 00 00)
2) Check the mothed of CI+ key by command (RS232: ci 00 20)
3) Result value i 01 OK 1d1852d21c1ed5dcx
3.6. WIFI MAC ADDRESS CHECK(1) Using RS232 Command
(2) Check the menu on in-start
4. Manual Adjustment* ADC adjustment is not needed because of OTP(Auto ADC
adjustment)
4.1 EDID DATA- HDMI1
- HDMI2
Reference- HDMI1 ~ HDMI2- In the data of EDID, bellows may be different by S/W or
Input mode.
4.2. White balance adjustmentRGB Gains are fixed data for each model. Insert RS-232C Jack which is connected with PC for White Balance or equiva-lent device.* Total Assembly line should be check whether the color
coordinate(x,y) data refer to below table were meet or not.
*Note : x,y coordinates are drifted about 0.007 after 30 mins heat-run. So checking color coordinate within 5-min at total assembly line, consider x,y coordinates might be up to 0.007 than x,y target of each color temperature.
H-freq(kHz) V-freq.(Hz)
Transmission [A][I][][Set ID][][20][Cr] [O][K][X] or [NG]
CMD 1 CMD 2 Data 0A A 0 0
CMD 1 CMD 2 Data 0C I 2 0
CI+ Key Value
128byte 256byte
HDMI1 43 1B
HDMI2 43 0B
Color Temperature
Cool 9,300k K X=0.290 (0.03)Y=0.298 (0.03)
Inner pattern(204gray,80IRE)
Medium 8,000k K X=0.300 (0.03)Y=0.310 (0.03)
Warm 6,500k K X=0.318 (0.03)Y=0.334 (0.03)
Luminance(cd/m)
Cool Min : 80 Typ : 160 Inner pattern(204gray,80IRE)Medium Min : 80 Typ : 160
Warm Min : 80 Typ : 160
- 13 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
*Note : Manual W/B process using adjusts Remote control. 1) After enter Service Mode by pushing "ADJ" key,2) Enter "White Balance" by pushing "" key at "White Bal-
ance".
* When doing Adjustment, Please make circumstance as below.
4.3. Magic Motion Remote control test- Equipment : RF Remote control for test, IR-KEY-Code Re-
mocon for test- You must confirm the battery power of RF-Remote control
before test(recommend that change the battery per every lot) - Sequence (test) a) If you select the start key(Wheel Key) on the controller,
you can pairing with the TV SET. b) You can check the cursor on the TV Screen, when select
the Wheel Key on the controller c) You must remove the pairing with the TV Set by select
Mute Key on the controller
4.4. HDMI ARC Function Inspection
4.4.1. Test equipment- Optic Receiver Speaker - MSHG-600 (SW: 1220 ) - HDMI Cable (for 1.4 version)
4.4.2. Test method1) Insert the HDMI Cable to the HDMI ARC port from the
master equipment (HDMI1)
2) Check the sound from the TV Set
3) Check the Sound from the Speaker or using AV & Optic TEST program
(Its connected to MSHG-600)
* Remark: Inspect in Power Only Mode and check SW version in a master equipment
GWUG{GvXG G GXUG{GvYG G GYUG{GvZG G GZUG{Gv[G G G[UG{Gv\G\UG{Gv]G G G]UGjGnG G G^UGhGvG_UGhkjGjG G G G G G G G G G G`UG~GiG G G G G G G G G GG G GXWUGXWGwG~iG G G GXXUG{GwG G G G GXYUGlkpkGkVsG G G G G G G G G G G G G G G GXZUGzGiVjGX[UG{GzGzGX\GlUGpGhG G GG G G ~GiGjG{UG G jG GyTnG G XWWG GnTnG G XW[G GiTnG G X`YG GyTjG G ][G GnTjG G ][G GiTjG G ][G G{TwG G vuG GiG G XWWG GyG G {GzG G
- 14 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
4.5. Wi-Fi TestStep 1) Turn on TVStep 2) Select Network Connection option in Network Menu.
Step 3) Select Start Connection button in Network Connec-tion.
Step 4) If the system finds any AP like blow PIC, it is working well.
4.6. LNB voltage and 22KHz tone check(only for DVB-S/S2 model) Test method1) Set TV in Adj. mode using POWER ON.2) Connect cable between satellite ANT and test JIG.3) Press Yellow key(ETC+SWAP) in Adj Remote control to
make LNB on.4) Check LED light ON at 18 V menu.5) Check LED light ON at 22 KHz tone menu.6) Press Blue key(ETC+PIP INPUT) in Adj Remote control to
make LNB off.7) Check LED light OFF at 18 V menu.8) Check LED light OFF at 22 KHz tone menu.
Test result1) After press LNB On key, 18 V LED and 22 KHz tone LED
should be ON. 2) After press LNB OFF key, 18 V LED and 22 KHz tone
LED should be OFF.
4.7. Option selection per country4.7.1. Overview
- Option selection is only done for models in Non-EU
4.7.2. Method1) Press ADJ key on the Adj. R/C, then select Country Group
Meun2) Depending on destination, select Country Group Code 04
or Country Group EU then on the lower Country option, select US, CA, MX. Selection is done using +, - or key.
5. Tool Option selection Method : Press "ADJ" key on the Adjustment remote control,
then select Tool option.
6. Ship-out mode check(In-stop) After final inspection, press "IN-STOP" key of the Adjustment
remote control and check that the unit goes to Stand-by mode.
7. GND and Hi-pot auto-check7.1. Method
1) GND & Hi-pot auto-check preparation- Check that Power cord is fully inserted to the SET. (If loose, re-insert)2) Perform GND & Hi-pot auto-check- Unit fully inserted Power cord, Antenna cable and A/V arrive
to the auto-check process. - Connect D-terminal to AV JACK TESTER- Auto CONTROLLER(GWS103-4) ON- Perform GND TEST- If NG, Buzzer will sound to inform the operator.- If OK, changeover to I/P check automatically. (Remove CORD, A/V form AV JACK BOX.)- Perform I/P test- If NG, Buzzer will sound to inform the operator.- If OK, Good lamp will lit up and the stopper will allow the pal-
let to move on to next process.
7.2. Checkpoint TEST voltage- GND: 1.5 KV / min at 100 mA- SIGNAL: 3 KV / min at 100 mA TEST time: 1 second TEST POINT- GND TEST = POWER CORD GND & SIGNAL CABLE
METAL GND- Internal Pressure TEST = POWER CORD GND & LIVE &
NEUTRAL LEAKAGE CURRENT: At 0.5 mArms
- 15 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
8. AudioMeasurement condition:1) RF input: Mono, 1 KHz sine wave signal, 100 % Modulation2) CVBS, Component: 1 KHz sine wave signal 0.5 Vrms3) RGB PC: 1 KHz sine wave signal 0.7 Vrms
9. USB S/W Download(Service only)1) Put the USB Stick to the USB socket.2) Automatically detecting update file in USB Stick.- If your downloaded program version in USB Stick is Low, it
didn't work. But your downloaded version is High, USB data is automatically detecting.(Download Version High & Power only mode, Set is automatically Download)
3) Show the message "Copying files from memory".
4) Updating is starting.
5) Updating Completed, The TV will restart automatically.6) If your TV is turned on, check your updated version and
Tool option. (explain the Tool option, next stage)* If downloading version is more high than your TV have, TV
can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didnt have a DTV/ATV test on production line.
* After downloading, have to adjust Tool Option again.1) Push "IN-START" key in service remote control.2) Select "Tool Option 1" and push "OK" key.3) Punch in the number. (Each model has their number)
No. Item Min Typ Max Unit
1.
Audio practical max Output, L/R(Distortion=10% max Output)
4.5 5 6 WEQ OffAVL OffClear Voice Off
2. Speaker (8Impedance) 4.5 5 6 WEQ OffAVL OffClear Voice Off
- 16 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
TROUBLE SHOOTING
1. No Power
Check L8804Voltage Level (19V)
Check Power connectorOK ?
Replace AdapterN N
Check IC2404 outputVoltage Level (5V)
Replace IC2404 &check
N
Check IC8807 OutputVoltage Level (3.3V_ST) Replace IC8807
N
Y
Check IC2400 outputVoltage Level (1.24V),Check IC2403 outputVoltage Level (1.5V)
Replace IC2400&IC2403Recheck
N
Y
Y
Y
Check X100 Clock27MHz
Replace X100N
Replace IC100 Flash Memory
Y
- 17 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
2. No Picture
Module Back Light On ?
Check WLED_ENABLE highIC10000 PIN #1
Check IC105Replace Main Scaler IC
N N
Check Panel clockP7100(#22,#23)
Check IC105Repair Main B/D
N
Check Panel powerP7100(#1~#3) 5V IC2404 output Replace IC2404
N
Y
Replace T-conBoard or module
Check FFC Cable for damage or open conductors. Replace Cable
N
Y
Y
Y
Check 19V(C2401)
Check DC JACKJK8800
N
Y
- 18 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
3. No Video- DIGITAL TV
Check RF Cable
Check Tuner(TU6406)DATA, CLK, SYN, VAL
Replace TU6406And recheck
Y
N
1. Check tuner(TU6401 #5 #32) Power 3.3V2. Check IC 2405 output voltage
Replace IC2405
Y
N
Check Tuner(TU6401) I2C signal#3 # 4 #34 #35
Check IC105
Y
N
1. Check tuner(TU6401 #7)Power 1.8V2. Check IC6403 output voltage(1.8V)
Replace IC6403
Y
N
- 19 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
4. No Video - ComponentCheck input signal format
Is it supported?
Check signalR362, R363, R364,C372, C373, C374
Replace R362, R363, R364,C372, C373, C374
Y
N
Check JK3801Replace JK3801 or
Check Device
Y
N
Y
IC105 has problem
Y
Check Component Cable
- 20 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
5. No Video - HDMICheck input signal format
Is it supported?
Y
Check JK3301 / JK3303for proper connection or damage
Replace connector
Y
N
Y
Check HDMI Cable for damage or open connector
Check I2C Signal (IC3304)(MHL IC HDMI 1) REPLACE IC3304
Y
N
Check HDCP KEY (IN-START MENU) WRITE HDCP KEYN
- 21 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
6. No Audio
Make sure you cant hear any audio and Device support the audio signal normally.
Check Speaker and its wire connection (P5400)
and the resistance
Check signal from IC8101P5400 output #1 #2 #3 #4
Y
Replace IC8101N
Check L5400 Voltage Level (19V)
Y
Check ADAPTER output or replace ADAPTER
N
Y
Check signal from IC105SCL / SDA
R5402 / R5403
Y
Replace IC105N
Replace connector or SpeakerN
- 22 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
BLOCK DIAGRAM
- 23 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes
EXPLODED VIEW
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
IMPORTANT SAFETY NOTICE
LV1
A2
535
300
200
120
900
540
400
921
910
920
600
820
800
810
510
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
CI_DATA[5]
CI_DATA[2]
CI_ADDR[2]
MT5398_TS_OUT[7]
CI_DATA[3]
CI_ADDR[11]
CI_ADDR[3]
EMMC_DATA[5]
CI_ADDR[12]
FE_DEMOD1_TS_DATA[5]
MT5398_TS_OUT[0]
MT5398_TS_OUT[2]
CI_ADDR[14]
MT5398_TS_OUT[4]
CI_DATA[0]
CI_ADDR[1]
CI_ADDR[13]
MT5398_TS_OUT[3]
FE_DEMOD1_TS_DATA[6]
MT5398_TS_OUT[1]
CI_ADDR[9]
CI_ADDR[7]
CI_DATA[4]
FE_DEMOD1_TS_DATA[1]
CI_DATA[1]
CI_ADDR[4]
FE_DEMOD1_TS_DATA[0]
CI_ADDR[6]
FE_DEMOD1_TS_DATA[3]FE_DEMOD1_TS_DATA[2]
CI_ADDR[0-14]
MT5398_TS_OUT[5]
EMMC_DATA[7]
FE_DEMOD1_TS_DATA[7]
FE_DEMOD1_TS_DATA[4]
CI_ADDR[8]
MT5398_TS_OUT[6]
CI_DATA[6]
CI_ADDR[10]
CI_ADDR[0]
CI_DATA[7]
EMMC_DATA[6]
EMMC_DATA[4]
EMMC_DATA[2]
CI_ADDR[5]
EMMC_DATA[3]
R109 33
/CI_CD1
R1561K
R1874.7KOPT
R1532.7K
N
O
N
_
T
U
_
Q
_
K
R
R
1
0
6
4
.
7
K
F
R
C
_
1
2
0
H
Z
M
D
S
6
2
1
1
0
2
1
3
M
1
0
1
M
S
7
3
_
S
M
D
_
G
A
S
K
E
T
R192 0
M_RFModule_RESET
R1601KOPT
I2C_SCL5
CTS
R126 22
R1834.7K
I2C_SDA6
I2C_SDA5
/PCM_WE
R1024.7KOPT
I2C_SCL1
MT5398_TS_CLK
EMMC_DATA[1]
R
1
3
1
4
.
7
K
M
T
K
_
D
D
R
_
1
.
2
5
G
B
R
1
3
0
4
.
7
K
M
O
D
U
L
E
_
V
1
3
+3.3V_NORMAL
MT5398_TS_IN[4]
STB_SDA
C1162.2uF10V
OPCTRL3
SOC_RX
I2C_SCL5
OSCL0
LED_PWM0
R
1
2
2
4
.
7
K
N
o
n
_
C
o
u
n
t
r
y
_
A
J
J
A
MODEL_OPT_5
R
1
9
0
1
0
K
MODEL_OPT_1
OPCTRL_0_SDA
OSCL2
/TU_RESET1
EMMC_CMD
MT5398_TS_IN[6]
M
D
S
6
2
1
1
0
2
1
3
M
1
0
3
M
S
7
3
_
S
M
D
_
G
A
S
K
E
T
R1322.7K
R16810K
MT5398_TS_OUT[0-7]
C1124.7uF10V
LED_PWM0
R1884.7K
R119 33
WOL/ETH_POWER_ON
R
1
4
5
4
.
7
K
M
T
K
_
D
V
B
_
S
_
T
U
N
E
R
OTP_WRITE
USB_CTL1
+3.3V_NORMAL
C1170.1uF16V
R100
4.7KOPT
R134 33
R1241.2K
RTS
R113 33
R1332.7K
R
1
0
5
4
.
7
K
C
o
u
n
t
r
y
_
T
W
OPCTRL_11_SCL
R
1
0
3
4
.
7
K
N
O
N
_
C
o
u
n
t
r
y
_
T
W
R1512.7K
R1551K
SC_ID_SOC
SOC_TX
R
1
4
0
4
.
7
K
M
T
K
_
D
V
B
_
T
2
_
T
U
N
E
R
R1014.7K
R
1
2
8
4
.
7
K
M
O
D
U
L
E
_
V
1
2
+3.3V_NORMAL
/PCM_CE1
MT5398_TS_IN[7]
I2C_SCL4
MODEL_OPT_5
OSDA0
AMP_RESET_N
/PCM_IOWR
R1631K
I2C_SCL1
OSCL0
MT5398_TS_IN[3]
OSCL1
USB_CTL3
+3.3V_NORMAL
R135 33
OSDA2
C1000.1uF16V
/PCM_WAIT
OPCTRL3
R1502.7K
C1110.1uF
MODEL_OPT_9
MODEL_OPT_8
R
1
4
9
4
.
7
K
M
T
K
_
E
P
I
MT5398_MISTRT
MODEL_OPT_7
R
1
0
8
4
.
7
K
M
T
K
_
F
H
D
MT5398_TS_IN[2]
MODEL_OPT_0
R
1
4
4
4
.
7
K
N
O
N
_
D
D
R
_
0
.
7
8
G
EMMC_DATA[0]
R1731K
OPCTRL7
R116 33
EMMC_RST
/PCM_IORD
I2C_SDA5
/CI_CD2
MODEL_OPT_3
STB_SCL
R1611KOPT
MODEL_OPT_6
R
1
3
9
4
.
7
K
M
T
K
_
N
O
N
_
D
V
B
_
T
2
_
T
U
N
E
R
R118 33
MT5398_TS_IN[0]
AMP_RESET_SOC
+3.3V_NORMAL
AV1_CVBS_DET
R191 0
OPCTRL_1_SCL
D100
100V
1N4148W
R1472.7K
R117 33
R18910KOPT
MT5398_TS_IN[1]
C1100.1uF
FE_DEMOD1_TS_DATA[0-7]
MT5398_XTAL_OUT
R
1
2
9
4
.
7
K
M
T
K
_
D
D
R
_
1
.
5
G
B
AVDD_33SB
CI_ADDR[0-14]
+3.3V_NORMAL
EMMC_DATA[2-7]
R115 33
+3.3V_NORMAL
R18510K
OSDA0
R1211.2K
R
1
3
6
4
.
7
K
M
T
K
_
N
O
N
_
C
P
_
B
O
X
R182
33
R120 33
LED_PWM1
OPCTRL_0_SDA
/S2_RESET
R1541K
O
P
T
FE_DEMOD1_TS_CLK
R
1
2
3
4
.
7
K
C
o
u
n
t
r
y
_
A
J
J
A
OPCTRL_10_SDA
SOC_RESET
/USB_OCD1
MODEL_OPT_2
MT5398_MIVAL_ERR
OPCTRL_10_SDA
C1090.1uF
MT5398_MCLKI
R
1
4
3
4
.
7
K
M
T
K
_
N
O
N
_
D
V
B
_
S
_
T
U
N
E
R
MODEL_OPT_6
R172 10K
FE_DEMOD1_TS_VAL
M
D
S
6
2
1
1
0
2
1
3
M
1
0
0
O
P
T
COMP1_DET
R1712.7KOPT
R127 22
C1074.7uF10V
I2C_SDA1
HP_DET
OSDA1
OPCTRL7
I2C_SDA4
R193 4.7K
R1744.7KOPT
EMMC_CLK
R
1
4
6
4
.
7
K
D
D
R
_
0
.
7
8
G
OTP_WRITE
/PCM_OE
R1382.7K
R1844.7K
M_REMOTE_TX
CI_DATA[0-7]
IC100-*2R1EX24256BSAS0A
NVRAM_RENESAS
3A2
2A1
4VSS
1A0
5SDA
6SCL
7WP
8VCC
RF_SWITCH_CTL
IC100AT24C256C-SSHL-T
NVRAM_ATMEL
3A2
2A1
4GND
1A0
5SDA
6SCL
7WP
8VCC
/USB_OCD3
VDD3V3
R
1
4
8
4
.
7
K
M
T
K
_
N
O
N
_
E
P
I
IC101M24C16-R
OPT
3NC_3
2NC_2
4VSS
1NC_1
5 SDA
6 SCL
7 WC
8 VCC
MODEL_OPT_10
R1621K
M_REMOTE_RX
R186
22
/S2_RESET
MODEL_OPT_7
LED_PWM1
R
1
8
0
4
.
7
K
R110 33
R1422.7K
R125 4.7K
I2C_SDA1
R158
22
AVDD_33SB
R
1
0
4
4
.
7
K
N
O
N
_
F
R
C
_
6
0
H
Z
/PCM_IRQA
MT5398_TS_VALCI_A_VS1
FE_DEMOD1_TS_SYNC
R114 33
MODEL_OPT_0
R1571KOPT
R1522.7K
N
O
N
_
T
U
_
Q
_
K
R
AVDD_33SB
R
1
0
7
4
.
7
K
M
T
K
_
H
D
/USB_OCD2
OPCTRL_11_SCL
STB_SCL
OSCL1
MT5398_TS_SYNC
R170 10K
R
1
3
7
4
.
7
K
M
T
K
_
C
P
_
B
O
X
MODEL_OPT_3
+3.3V_NORMAL
+3.3V_NORMAL
OPCTRL_1_SCL
R178 22
MT5398_XTAL_IN
R169 10KNON_EU
/PCM_REG
R111 33
SC_DET
EMMC_CLK
OSDA1
STB_SDA
AMP_RESET_SOC
IC100-*1M24256-BRMN6TP
NVRAM_ST
3E2
2E1
4VSS
1E0
5SDA
6SCL
7WC
8VCC
PCM_RST
R1412.7K
I2C_SCL6
+3.3V_NORMAL
MT5398_TS_IN[5]
MT5398_XTAL_IN
PWM_DIM1
MT5398_XTAL_OUT
R112 33
M
D
S
6
2
1
1
0
2
1
3
M
1
0
2
O
P
T
/TU_RESET2
R31524K
TXB3P
PCM_5V_CTL
D0+_HDMI1_SOC
VDD3V3
C38722pFOPT
EPHY_RDP
USB_DM1
DDC_SDA_3_JACK
TP381
CK-_HDMI3_JACK
TXA1N
EPHY_TDN
TXBCLKP
TXB2P
C39322pFOPT
C3580.1uF
C38922pFOPT
R3521.2K
AVDD3V3_AADC
COMP1/AV1/DVI_R_IN_SOC
USB_DP2EPHY_RDN
C3951200pF
R3820
TXA2P
TXB0P
VDD3V3
R3511.2K
D2+_HDMI1_SOC
C3070.1uF
C3620.1uF
DDC_SCL_1_SOC
CK-_HDMI1_SOC
WIFI_DP
R3691.2K
SC_R_IN_SOC
C3631uF10V
C3040.1uF
TUNER_SIF
DDC_SCL_3_JACK
HDMI_HPD_3_JACK
TXA3P
D2+_HDMI3_JACK
C3030.1uF
D0+_HDMI3_JACK
MODEL_OPT_2
TXB3N
TXA0P
TXB2N
WIFI_DM
CK+_HDMI1_SOC
COMP1/AV1/DVI_L_IN_SOC
DDC_SCL_MHL
TXB1P
TXA1P
SCART_Rout_SOC
AUD_MASTER_CLK
AVDD3V3_AADC
D1+_HDMI3_JACK
VDD3V3_HDMI
D0+_HDMI4_MHL
AUD_LRCH
5V_HDMI_3_JACK
+1.2V_MTK_AVDD
HDMI_HPD_4_MHL
C3901200pF
USB_DP1
D1-_HDMI4_MHL
SCART_Lout_SOC
DDC_SDA_MHL
MODEL_OPT_10
C3020.1uF
USB_DP3
R306 1K
D2-_HDMI4_MHL
SC_L_IN_SOC
CK-_HDMI4_MHL
D0-_HDMI1_SOC
USB_DM3
AUD_LRCK
TXA3N
MODEL_OPT_9
D2+_HDMI4_MHL
C3540.1uF
R366 100
R3392.2KOPT
HP_ROUT_MAIN
CK+_HDMI3_JACKR307 1KD2-_HDMI3_JACK
R3701.2K
D1-_HDMI3_JACK
ARC
TXB0N
C3470.1uF
DDC_SDA_1_SOC
D0-_HDMI3_JACK
L304
D0-_HDMI4_MHL
VDD3V3
R305 1K
AUD_SCK
C3280.1uF
R383
0
MODEL_OPT_8
D2-_HDMI1_SOC
CK+_HDMI4_MHL
R371 100
TXB1N
AVDD_33SB
R34324K1%
EPHY_TDP
D1-_HDMI1_SOC
C3051uF10V
TXBCLKN
C36510uF10V
5VBUS
C352 0.01uF
TU_A_GLOBAL_6/7
D1+_HDMI4_MHL
TXA2N
R368 100
TXA0N
C3831200pF
5V_HDMI_1_SOC
TXACLKN
HP_LOUT_MAIN
USB_CTL2
C39633pFOPT
C3060.1uF
R367 100
HDMI_HPD_1_SOCD1+_HDMI1_SOC
USB_DM2
+1.2V_MTK_AVDD
AVDD3V3_AADC
C3771200pF
TXACLKP
BLU_CURRENT_CTL
R8915 22
R891622
R71001K
TXA3N
TXB2P
TXACLKN
TXACLKP
TXBCLKP
C71001000pF50V
TXB1P
TXB2N
C71020.1uF50V
TXB3N
P710010031HR-30
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
TXA1P
C710110uF16V
TXA3P
TXA1N
R71051K
PANEL_VCC
C7103100uF16V
TXB3P
TXBCLKN
R71061K
TXB0P
TXA0N
JP7100
TXB0N
TXA2P
TXA0P
TXB1N
TXA2N
R71071K
C3720.01uF
R340 100
TU_A_GLOBAL_6/7R341 100C359 0.047uFTU_A_GLOBAL_6/7
+1.2V_MTK_AVDD
TU_CVBS
SC_FB_SOC
+1.2V_MTK_AVDD
C361 1uF
TP300
VDD3V3
C3640.1uF
R3311K
TU_S/N/Q_T/US/KR/TW
COMP1_Y_SOC
TP304
R3490OPT
C3820.1uF
COMP1_Pr_SOC
IF_P
SC_R_SOC
R342 10KTU_S/N/Q_T/US/KR/TW TP301
R332 10KTU_S/N/Q_T/US/KR/TW
SC_G_SOC
C3740.01uF
C3510.1uF
C3751500pF
TP376
COMP1_COM_SOC
OSDA2
TP382
C310
33pFTU_S/N/Q_T/US/KR/TW
TP302
SC_B_SOC
R3461K
TU_S/N/Q_T/US/KR/TW
C337 1uF
10VTU_S/N/Q_T/US/KR/TW
COMP1_Pb_SOC
C336 1uF10V
TU_S/N/Q_T/US/KR/TW
C3550.047uF
TU_S/N/Q_T/US/KR/TW
R335 51
TU_S/N/Q_T/US/KR/TWVDD3V3
VDD3V3
OSCL2
C3410.047uF
TU_S/N/Q_T/US/KR/TW
SC_CVBS_IN_SOC
IF_N
C3710.01uF
IF_AGC
SC_COM_SOC
AV1_CVBS_SOC
R334 51
TU_S/N/Q_T/US/KR/TW
C360 0.047uF
DTV/MNT_V_OUT_SOC
R
3
8
0
1
K
T
U
_
S
/
N
/
Q
_
T
/
U
S
/
K
R
/
T
W
TP306
C312
33pF
TU_S/N/Q_T/US/KR/TW
TP305
TP383
C3730.01uF
TP303
PC_R_IN_SOC
PC_L_IN_SOC
C1141.0pF50V
DVB_1pF
C1151.0pF50V
DVB_1pFC114-*12.7pF50V
ATSC_2.7pF
C115-*12.7pF50V
ATSC_2.7pF
MODEL_OPT_1
R
1
9
4
1
0
K
R
1
9
5
1
0
K
VDD3V3
PC_AUDIO_DET
#SIL_RESET
C3500.1uF
X10027MHz
4GND_2
1X-TAL_1
2GND_1
3X-TAL_2
IC105LGE2122[A2_M13]
USB_DP_P0H32
USB_DM_P0H33
USB_DP_P1J32
USB_DM_P1J31
USB_DP_P2K32
USB_DM_P2K31
USB_DP_P3AN10
USB_DM_P3AM10
AVDD33_USB_P0P1P2K33
AVDD33_USB_P3AN8
AVSS33_USB_P1M25
AVSS33_USB_P3AE11
TXVP_0AL13
TXVN_0AM13
RXVP_1AL12
RXVN_1AM12
PHYLED1AF13
PHYLED0AJ13
REXTAN12
AVDD33_ETHAN14
AVSS33_ELDOAE13
AVSS33_LDAC16
AVSS33_COMAC15
IC105LGE2122[A2_M13]
GPIO0B30
GPIO1A31
GPIO2B31
GPIO3A32
GPIO4C30
GPIO5A33
GPIO6B32
GPIO7C31
GPIO8E30
GPIO9F29
GPIO10F27
GPIO11F28
GPIO12C32
GPIO13F30
GPIO14F32
GPIO15D30
GPIO16D32
GPIO17F31
GPIO18F33
GPIO19E31
GPIO20E32
GPIO21D31
GPIO22D33
GPIO23E29
GPIO24C33
GPIO25B33
GPIO26A30
GPIO27E28
GPIO28C29
GPIO29J28
GPIO30H29
GPIO31J26
GPIO32G30
GPIO33G27
GPIO34E27
GPIO35D29
GPIO36D28
GPIO37H28
GPIO38J27
GPIO39G29
GPIO40G31
GPIO41G28
GPIO42B28
GPIO43K28
GPIO44E25
GPIO45D21
GPIO46G23
GPIO47C28
GPIO48F24
GPIO49AB8
GPIO50AA7
GPIO51AD6
GPIO52AC8
GPIO53AC7
GPIO54AB6
GPIO55AC6
ADIN0_SRVAJ23
ADIN1_SRVAH23
ADIN2_SRVAE28
ADIN3_SRVAD28
ADIN4_SRVAF22
ADIN5_SRVAK21
ADIN6_SRVAG24
ADIN7_SRVAM18
DEMOD_RSTP30
DEMOD_TSCLKN32
DEMOD_TSDATA0R27
DEMOD_TSDATA1T26
DEMOD_TSDATA2T27
DEMOD_TSDATA3P26
DEMOD_TSDATA4R28
DEMOD_TSDATA5U27
DEMOD_TSDATA6U26
DEMOD_TSDATA7R26
DEMOD_TSSYNCR29
DEMOD_TSVALP27
CI_INTL25
CI_TSCLKN33
CI_TSDATA0K26
CI_TSSYNCN30
CI_TSVALN31
PVR_TSCLKM31
PVR_TSVALM27
PVR_TSSYNCL27
PVR_TSDATA0M29
PVR_TSDATA1M30
SPI_CLK1L30
SPI_CLKL33
SPI_DATAL32
SPI_CLEK27
OPWM2AL8
OPWM1AM8
OPWM0AM9
SD_D0D27
SD_D1C27
SD_D2D26
SD_D3C26
SD_CMDA28
SD_CLKE24
LED_PWM1AF15
LED_PWM0AG15
OPCTRL11AL16
OPCTRL10AM16
OPCTRL9AE17
OPCTRL8AG19
OPCTRL7AH17
OPCTRL6AE19
OPCTRL5AH19
OPCTRL4AK16
OPCTRL3AG17
OPCTRL2AJ17
OPCTRL1AF19
OPCTRL0AJ19
IC105LGE2122[A2_M13]
JTCKAK10
JTDIAK11
JTDOAL9
JTMSAJ11
JTRSTAJ12
OSDA0AH11
OSCL0AH10
OSDA1AF11
OSCL1AG11
XTALIAN29
XTALOAM29
AVDD33_XTAL_STBAN30
AVSS33_XTAL_STBAL29
AVDD33_VGA_STBAN17
AVSS33_AVSS33_VGA_STBAL17
AVDD33_PLLAL26
AVSS33_PLLGPAC21
AVSS33_CPUPLLH21
AVDD10_LDOAM17
AVDD10_ELDOAN16
U0TXAH15
U0RXAH14
U1TXAH13
U1RXAG13
POWED24
POOEB25
POCE1D25
POCE0A25
PDD7C22
PDD6B22
PDD5A22
PDD4C23
PDD3A23
PDD2B23
PDD1D23
PDD0C24
PARBC25
PACLEA26
PAALEB26
EMMC_CLKC21
OPWRSBAL15
ORESETAK20
OIRIAF17
FSRC_WRC20
STB_SCLAL14
STB_SDAAK15
POR_BNDAE14
IC105LGE2122[A2_M13]
HDMI_CECV26
HDMI_0_SCLAC27
HDMI_1_SCLAB27
HDMI_2_SCLAA26
HDMI_3_SCLW27
HDMI_0_SDAAC26
HDMI_1_SDAAB26
HDMI_2_SDAY26
HDMI_3_SDAW26
HDMI_0_PWR5VAE29
HDMI_1_PWR5VY27
HDMI_2_PWR5VAA28
HDMI_3_PWR5VV28
HDMI_0_HPDAD29
HDMI_1_HPDAA27
HDMI_2_HPDAA29
HDMI_3_HPDV29
AVDD12_HDMI_0_RXAA33
AVDD12_HDMI_1_RXAA32
AVDD12_HDMI_2_RXP33
AVDD12_HDMI_3_RXP32
AVDD33_HDMIAH33
AVSS33_HDMI_RX_1AE27
AVSS33_HDMI_RX_2T25
AVSS33_HDMI_RX_3W25
AVSS33_HDMI_RX_4AD27
HDMI_0_RX_0AG30
HDMI_0_RX_0BAG31
HDMI_0_RX_1AF30
HDMI_0_RX_1BAF31
HDMI_0_RX_2AE32
HDMI_0_RX_2BAE33
HDMI_0_RX_CAG32
HDMI_0_RX_CBAG33
HDMI_1_RX_0AD30
HDMI_1_RX_0BAD31
HDMI_1_RX_1AC32
HDMI_1_RX_1BAC33
HDMI_1_RX_2AC30
HDMI_1_RX_2BAC31
HDMI_1_RX_CAE30
HDMI_1_RX_CBAE31
HDMI_2_RX_0Y30
HDMI_2_RX_0BY31
HDMI_2_RX_1W32
HDMI_2_RX_1BW33
HDMI_2_RX_2W30
HDMI_2_RX_2BW31
HDMI_2_RX_CAA30
HDMI_2_RX_CBAA31
HDMI_3_RX_0U30
HDMI_3_RX_0BU31
HDMI_3_RX_1T32
HDMI_3_RX_1BT33
HDMI_3_RX_2T30
HDMI_3_RX_2BT31
HDMI_3_RX_CV30
HDMI_3_RX_CBV31
IC105LGE2122[A2_M13]
ADCINP_DEMODAM27
ADCINN_DEMODAN27
AVDD33_DEMODAN26
AVDD12_DEMODAN28
AVSS33_DEMODAL28
AVSS12_DEMODAL27
IF_AGCL26
RF_AGCM28
LOUTNAJ27
LOUTPAK27
OSCL2N27
OSDA2N26
CVBS3PAK26
CVBS2PAM25
CVBS1PAH26
CVBS0PAK25
CVBS_COMAJ26
AVDD33_CVBSAM26
AVSS33_CVBS_1AB20
AVSS33_CVBS_2AB22
HSYNCAK18
VSYNCAL18
RPAL20
GPAM20
BPAL19
COMAN20
SOGAK19
VGA_SDAAG22
VGA_SCLAH22
COM1AL21
PB1PAK22
PR1PAL22
Y1PAM21
SOY1AN21
COM0AM23
PB0PAL23
PR0PAL24
Y0PAN23
SOY0AK23
VDACX_OUTAH24
VDACY_OUTAJ24
AVDD33_VIDEOAN25
AVDD12_RGBAN18
AVSS33_VDAC_BGAC19
AVSS12_RGBAK17
AVSS33_VDACAE20
IC105LGE2122[A2_M13]
AIN1_R_AADCAL32
AIN1_L_AADCAN32
AIN2_R_AADCAM33
AIN2_L_AADCAM31
AIN3_R_AADCAM32
AIN3_L_AADCAK33
AIN4_R_AADCAL33
AIN4_L_AADCAN33
AVDD33_AADCAJ32
AVSS33_AADCAC24
VMID_AADCAN31
MPXPAH25
AR0_ADACAK30
AL0_ADACAJ29
AR1_ADACAJ31
AL1_ADACAK29
AR2_ADACAJ30
AL2_ADACAH28
AVDD33_ADACAJ33
AVSS33_ADACAC23
ALINAG9
ASPDIF0AG10
ASPDIF1V27
AOBCKAK9
AOLRCKAJ9
AOMCLKAF10
AOSDATA4AH9
AOSDATA3AK8
AOSDATA2AJ8
AOSDATA1AH8
AOSDATA0AJ10
IC105LGE2122[A2_M13]
TCON0AA8
TCON1AA9
TCON2W6
TCON3U6
TCON4U7
TCON5V8
TCON6V6
TCON7AB7
TCON8W9
TCON9U8
TCON10U9
TCON11V9
TCON12V7
AVDD12_LVDS_1AN1
AVDD12_LVDS_2AN2
AVDD12_LVDS_3AN3
AVDD33_LVDSAN4
AVSS12_LVDS_1AM4
AVSS12_LVDS_2AM3
AVSS12_LVDS_3AF5
AVSS33_LVDS_1AE5
AVSS33_LVDS_2AC5
AVSS33_LVDS_3V5
REXT_VPLLT1
BE0PY1
BE0NY2
BE1PW3
BE1NW4
BE2PV3
BE2NV4
BECKPV1
BECKNV2
BE3PU3
BE3NU4
BE4PT3
BE4NT4
BO0PAD1
BO0NAD2
BO1PAC3
BO1NAC4
BO2PAB3
BO2NAB4
BOCKPAB1
BOCKNAB2
BO3PAA3
BO3NAA4
BO4PY3
BO4NY4
AE0PAH1
AE0NAH2
AE1PAG3
AE1NAG4
AE2PAF3
AE2NAF4
AECKPAF1
AECKNAF2
AE3PAE3
AE3NAE4
AE4PAD3
AE4NAD4
AO0PAM1
AO0NAM2
AO1PAL3
AO1NAL4
AO2PAK3
AO2NAK4
AOCKPAK1
AOCKNAK2
AO3PAJ3
AO3NAJ4
AO4PAH3
AO4NAH4
/RST_HUB/RST_HUB
Q100PMV48XP
G
D S
R196240
CAM_SLIDE_DET
CAM_SLIDE_DET
I2C_SDA_MICOMI2C_SCL_MICOM
R36151R36251R36351R36451
C3985pF50V
OPTC3995pF50V
OPT
R152-*1
1.5KTU_Q_KR
R152-*2
1.2KTU_N_TW/BR
R153-*2
1.2KTU_N_TW/BR
R153-*1
1.5KTU_Q_KR
R35010EU
1 8
MT93/MS73 2013.01.15
EAX65029603
Wake On Lan
I2C
X-TAL
EXTERNAL DEMOD-> SOC
SOC -> CI SLOT
CI SLOT -> SOC
HEAT SINK SMD GASKET
MODEL_OPT_4
5V Tolerance
Model Option
CI SLOT -> SOC
I2C_1 : AMP, L/DIMMING,HDCP KEYI2C_2 : T-CONI2C_3 : MICOMI2C_4 : S/Demod,T2/Demod,LNB,MHL(Sil1292)I2C_5 : NVRAMI2C_6 : TUNER_MOPLL(T/C,ATV)
SOC -> CI SLOT
HDCP EEPROM
CI SLOT -> SOC
NVRAM
Write Protection
- Low : Normal Operation- High : Write Protection
MODEL_OPT_4
CI SLOT -> SOC
GPIO45(EMMC_RST) is dedicated to resetEMMC for improving A1s leakage current
Close to eMMC Flash(IC8100)
STRAPPING LED_PWM0 LED_PWM1 OPCTRL3 OPCTRL7
ICE mode + 27M + serial boot 1 0 0 0
ICE mode + 27M + ROM to Nand boot 1 0 0 1
ICE mode + 27M + ROM to 60bit ECC Nand boot 1 0 1 0
ICE mode + 27M + ROM to eMMC boot from 1 0 1 1 EMMC pins (share pins w/s NAND)
ICE mode + 27M + ROM to eMMC 1 1 0 0Boot from SDIO pins
Ready For commercial Audio_R_OUT
Dont use as GPIO
Wake On Lan
For PCB Pattern
Close to AVDD33_ADAC & AVDD33_AADC
HDMI_CEC
For PCB Pattern
Ready For commercial Audio_L_OUT
2D3D_COntrol
LVDS [31Pin LVDS OUTPUT Connector]
Close to Tuner
Close to MT5369
For PCB Pattern
For PCB Pattern
Close to MT5369
Near the SOC
20120813 LCD-TV
20120813 LCD-TV
FHD
V12
Reserved
HD
DDR_1.5G
Not Support
T2 Tuner
FRC(120Hz)
MODEL_OPT_8
Not Support
MODEL_OPT_3
Country_TW
DDR
Support
Module
MODEL_OPT_9
DDR_1.25G
EPI
V13
LOW
MODEL_OPT_0
MODEL_OPT_10 Not Support
Enable
MODEL_OPT_1
MODEL_OPT_2 Panel
HIGH
MODEL_OPT_4
Support
No FRC(60Hz)
S Tuner
Support
Default
CP BOX Disable
FRC
MODEL_OPT_6
MODEL_OPT_5
MODEL_OPT_7
BOOT STRAP
20120813 LCD-TV
20120813 LCD-TV
20120813 LCD-TV
20120813 LCD-TV
20121115 LCD-TV
GCLK_SOCMCLK_SOCGST_SOCEO_SOCVCOM_DYNPMIC_RESET
20120813 Delete needless port
20120813 Delete needless port
L/DIM0_SCLKL/DIMO_MOSIEPI_LOCK6L/DIM0_VSGCLK_SOCMCLK_SOCGST_SOCEO_SOCVCOM_DYNPMIC_RESET
L/DIM0_MOSIL/DIM0_SCLK
L/DIM0_VS
20120813 Delete needless port
20120813 LCD-TV
20121023
20120813 Delete optic port
20120813 CJ.LIMDelete I2C_SCL2Delete I2C_SDA2
MAIN
20120813 Delete needless portEPI_LOCK6Add PC_AUDIO_DET
20120813 CJ.LIMLCD-TV
20120813 CJ.LIMLCD-TV
20120813 CJ.LIMLCD-TVAPPLY->OPT
20120813 CJ.LIMLCD-TV 1uF->0.1uF
[DV1]
2012.10.16 LCD-TV
[DV1]
[DV1]
[DV1]
[DV1]
[DV1]
[DV1]enable
[DV1]
PV_LCD-TV
PV_LCD-TV PV_LCD-TV
PV_LCD-TV
TW Non_TW
Country_AJJA AJJA Non_AJJA
[DV2]
[DV2]
[MP]
[MP]
[MP] [MP]
Copyright 2013 LG Electronics. Inc. All right reserved. Only for training and service purposes
LGE Internal Use Only
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
BRA[2]
ARDQ[23]
BRDQ[5]
BRDQ[9]
ARDQ[0]
BRDQ[6]
ARDQ[16]
ARDQ[9]
BRA[15]
ARDQ[24]
ARA[4]
BRA[4]
ARDQ[22]
ARA[14]
ARDQ[2]
BRA[0]
BRA[9]
BRDQ[2]
ARDQ[5]
ARDQ[12]
BRA[7]
BRA[13]
ARA[3]
BRDQ[8]
ARDQ[17]
BRDQ[4]
ARA[6]
ARDQ[11]
ARA[10]
BRDQ[14]BRDQ[13]
ARA[9]
ARDQ[25]
BRA[6]
ARDQ[7]
BRDQ[0]
ARDQ[1]
ARA[7]
ARDQ[31]
BRA[3]
ARDQ[18]
BRDQ[7]
ARDQ[10]
ARDQ[8]
ARA[8]
ARA[12]
BRDQ[15]
BRDQ[3]
ARDQ[6]
ARDQ[26]
ARA[1]
ARDQ[27]
ARDQ[19]
BRDQ[12]
ARA[0]
ARDQ[20]
ARDQ[28]
ARDQ[14]
BRA[1]
ARA[11]
BRDQ[1]
BRA[8]
BRA[10]
ARDQ[30]ARDQ[29]
BRDQ[10]BRDQ[11]
BRA[14]
ARDQ[15]
ARDQ[3]ARDQ[4]
ARDQ[13]
BRA[11]
BRA[5]
BRA[12]
ARA[5]
ARDQ[21]
ARA[13]
ARA[2]
ARA[0]
ARDQ[21]
ARDQ[1]
ARDQ[27]ARDQ[26]
ARDQ[2]
ARDQ[22]
ARA[6]
ARDQ[20]
ARDQ[6]
ARA[1]
ARDQ[23]
ARDQ[9]
ARDQ[7]
ARA[4]
ARA[8]
ARA[13]
ARA[2]
ARDQ[4]
ARDQ[28]
ARDQ[16]
ARDQ[10]
ARDQ[30]
ARA[8]
ARA[5]
ARA[11]
ARDQ[18]
ARA[10]
ARA[6]
ARDQ[13]
ARA[5]
ARA[3]
ARA[9]
ARA[3]
ARDQ[25]
ARA[2]
ARDQ[24]
ARDQ[3]
ARA[4]
ARA[13]
ARDQ[29]
ARA[7] ARA[7]
ARDQ[12]
ARDQ[0]
ARDQ[14]
ARA[12]
ARDQ[11]
ARA[1]
ARDQ[17]
ARDQ[31]ARDQ[15]
ARA[12]
ARA[10]ARA[11]
ARDQ[19]
ARA[0]
ARDQ[5]
ARA[9]
ARA[14] ARA[14]
ARDQ[8]
BRA[1]
BRA[8]
BRDQ[11]
BRA[2]
BRA[11]
BRDQ[13]
BRDQ[2]
BRDQ[8]
BRDQ[4]
BRDQ[12]
BRDQ[9]
BRA[13]
BRDQ[15]
BRDQ[3]
BRA[7]
BRDQ[1]
BRDQ[14]
BRDQ[5]
BRA[6]
BRA[3]
BRA[5]
BRDQ[6]
BRA[10]
BRA[4]
BRA[12]
BRA[9]
BRDQ[0]
BRA[0]
BRDQ[10]
BRDQ[7]
CI_ADDR[4]
CI_ADDR[13]
CI_DATA[6]
CI_ADDR[0]
CI_DATA[0]
CI_ADDR[9]CI_ADDR[8]
MT5398_TS_OUT[2]
MT5398_TS_OUT[7]
CI_DATA[5]
CI_DATA[7]
MT5398_TS_OUT[6]
MT5398_TS_OUT[3]
CI_DATA[1]
MT5398_TS_OUT[1]
CI_ADDR[10]
CI_ADDR[14]
CI_DATA[2]
CI_ADDR[7]
CI_ADDR[3]
CI_DATA[4]
MT5398_TS_OUT[5]
CI_ADDR[6]
MT5398_TS_OUT[4]
CI_ADDR[1]
CI_ADDR[12]
CI_DATA[3]
CI_ADDR[5]
CI_ADDR[2]
MT5398_TS_OUT[0]
CI_ADDR[11]
+1.2V_MTK_CORE
VDD3V3
+1.5V_DDR
C5390.1uF
OPTC5410.1uF16V
OPT+1.5V_DDR
C5090.1uF
C5110.1uF
+3.3V_NORMAL
L502BLM18PG121SN1D
OPT
VDD3V3
C5350.1uF
OPT
C5310.1uF16V
C5070.1uF
L505BLM18PG121SN1D
+1.2V_MTK_CORE
3.3V_EMMC
C51410uF
C5082.2uF
C5040.1uF
OPT+1.2V_MTK_CORE
TP501
C50310uF
C5200.1uF
L504BLM18PG121SN1D
C5060.1uF
+1.2V_MTK_AVDD
C50510uF
POWER_ON/OFF1
+1.2V_MTK_CORE
C51710uF
C5320.1uF
LAN_JACK_POWER
C51810uF
L501BLM18PG121SN1D
C5270.1uF
OPTC51310uF
OPT
L503BLM18PG121SN1D
OPT
VDD3V3
+3.3V_NORMAL
TP500
AVDD_33SB+3.5V_ST_WAKE
/ARCAS
C7470.1uF
ARBA1
/ARDQS1
/ARDQS3
+1.5V_DDR
/ARWE
/ARCLK0
ARDQS0
BRDQM1
BRBA0
/BRCLK0
RVREF_A
BRDQM0
/ARDQS0
TP700
+1.5V_DDR
ARCLK1
C7410.1uF
R7301K1%
RVREF_C
/ARCLK1
/ARCS
/ARRAS
BRCKE
C7420.1uF
ARDQS3
/BRCAS
ARA[0-14]
RVREF_C
/BRRAS
ARDQ[0-7]
BRODT
ARDQ[8-15]
R7271K1%
ARDQM3
ARDQS2
ARBA0
BRDQ[8-15]
+1.5V_DDR
BRDQ[0-7]
RVREF_A
BRCLK0
ARDQM2
ARDQ[24-31]
BRREST
/ARCSX
BRDQS1
C7460.1uF
BRA[0-15]
BRDQS0
C7000.1uF
ARBA2
BRBA1
+1.5V_DDR
/BRCS
R7311K1%
TP701
/BRDQS1
/BRWE
ARCLK0
ARCKE
ARODT
ARREST
BRBA2
R7261K1%
/ARDQS2
ARDQM1ARDQS1
/BRDQS0
VDD3V3
ARDQ[16-23]
ARDQM0
ARDQS3
A_RVREF4
ARDQM3
ARDQ[24-31]
C7350.1uF
C7360.1uF
/ARCAS
/ARDQS1
ARBA1
A_RVREF4
A_RVREF3
C7160.1uF
/ARCS/ARCLK0
A_RVREF2
R7211K1%
/ARDQS0
A_RVREF1
C7130.1uF
A_RVREF3
ARBA0ARBA1
ARA[0-14]
R7181K1%
C7330.1uF
R7091K1%
+1.5V_DDR
ARODT
C7140.1uF
ARCKE
ARA[0-14]
+1.5V_DDR
/ARCAS
/ARCSX
+1.5V_DDR
ARBA2
R710 2401%
R7081K1%
A_RVREF1
ARDQM2
ARODT
ARDQ[8-15]
+1.5V_DDR
R7121005%
/ARDQS3
R7162401%
ARDQS1
R7061K1%
+1.5V_DDR
ARDQ[16-23]
R7191K1%ARBA0
/ARDQS2
/ARWE
R7201K1%
ARCLK0
ARDQM0
C7340.1uF
/ARRAS
ARREST
ARDQ[0-7]
ARBA2
ARDQS2
C7150.1uF
ARDQS0
R7141005%
R7071K1%
/ARWE
ARCKE
/ARCLK1
ARCLK1
ARDQM1
+1.5V_DDR
/ARRAS
A_RVREF2
ARREST
BRDQS1
+1.5V_DDR
BRBA2
B_RVREF5
B_RVREF6
BRDQM1BRDQM0
/BRCS
B_RVREF6
+1.5V_DDR
C7090.1uF
/BRDQS0
/BRRAS
R7131005%
R7051K1%
/BRWE
BRA[14]
R7021K1%
/BRDQS1
BRA[0-14]
C7120.1uF
BRCLK0
BRDQ[0-7]
+1.5V_DDR
R7031K1%
/BRCLK0
BRODT
B_RVREF5
BRA[15]
BRREST
C7100.1uF
BRBA0
BRCKE
BRDQS0
BRDQ[8-15]
BRBA1
C7110.1uF
R711 2401%
R7041K1%
/BRCAS
H5TQ2G63BFR-PBCIC702
DDR_256M_HYNIX
A0N3
A1P7
A2P3
A3N2
A4P8
A5P2
A6R8
A7R2
A8T8
A9R3
A10/APL7
A11R7
A12/BCN7
A13T3
A15M7
BA0M2
BA1N8
BA2M3
CKJ7
CKK7
CKEK9
CSL2
ODTK1
RASJ3
CASK3
WEL3
RESETT2
DQSLF3
DQSLG3
DQSUC7
DQSUB7
DMLE7
DMUD3
DQL0E3
DQL1F7
DQL2F2
DQL3F8
DQL4H3
DQL5H8
DQL6G2
DQL7H7
DQU0D7
DQU1C3
DQU2C8
DQU3C2
DQU4A7
DQU5A2
DQU6B8
DQU7A3
VREFCAM8
VREFDQH1
ZQL8
VDD_1B2
VDD_2D9
VDD_3G7
VDD_4K2
VDD_5K8
VDD_6N1
VDD_7N9
VDD_8R1
VDD_9R9
VDDQ_1A1
VDDQ_2A8
VDDQ_3C1
VDDQ_4C9
VDDQ_5D2
VDDQ_6E9
VDDQ_7F1
VDDQ_8H2
VDDQ_9H9
NC_1J1
NC_2J9
NC_3L1
NC_4L9
NC_6T7
VSS_1A9
VSS_2B3
VSS_3E1
VSS_4G8
VSS_5J2
VSS_6J8
VSS_7M1
VSS_8M9
VSS_9P1
VSS_10P9
VSS_11T1
VSS_12T9
VSSQ_1B1
VSSQ_2B9
VSSQ_3D1
VSSQ_4D8
VSSQ_5E2
VSSQ_6E8
VSSQ_7F9
VSSQ_8G1
VSSQ_9G9
C7280.1uF
C70110uF10V
C7250.1uF
1uFC703
C7170.1uF
+1.5V_DDR
C7500.1uF
C7270.1uF
C7230.1uF
C7260.1uF
C7200.1uF
C7180.1uF
1uFC706 C708
10uF10V
C7190.1uF
C7220.1uF
+1.5V_DDR
C7510.1uF
C7530.1uF
C70410uF10V
C7540.1uF 1uF
C702C7450.1uF
+1.5V_DDR
C7550.1uF
C70710uF10V
1uFC705
+1.5V_DDR
/CI_CD2
MT5398_TS_IN[2]
SC_COM_SOC
/PCM_REG TP308
TP354
TP335
TP311
MT5398_TS_IN[5]
TP309TP310
/PCM_WAIT
/PCM_IOWR
TP314
TP307
/PCM_OE
MT5398_TS_IN[3]
PCM_5V_CTL
TP349
TP325
TP355
TP361
TP378
TP341
TP316
SC_FB_SOC
TP347
TP331
SCART_Rout_SOC
TP366
TP339
TP375
TP334
TP357
TP372
TP327
TP332
TP362
TP358
TP352
SC_R_IN_SOC
CI_A_VS1
MT5398_TS_IN[4]
MT5398_TS_OUT[0-7]
TP338
MT5398_TS_CLK
TP328
SC_ID_SOC
TP344
TP350
MT5398_MIVAL_ERR
TP326
/PCM_IRQA
TP345
TP321
SC_R_SOC
SC_CVBS_IN_SOC
TP317
MT5398_MCLKI
TP324
TP373
TP340
TP371
PCM_RST
/PCM_CE1
SC_G_SOC
MT5398_TS_SYNC
MT5398_TS_IN[6]
TP313
TP346
SC_DET
/CI_CD1
TP342
CI_ADDR[0-14]
TP318
/PCM_IORD
/PCM_WE
TP356
TP374
DTV/MNT_V_OUT_SOC
TP363
CI_DATA[0-7]
TP377
TP323
TP365
TP320
TP343
TP330
TP333
TP367
TP360
MT5398_TS_IN[7] TP353
MT5398_TS_VAL
MT5398_TS_IN[0]
TP319
SC_B_SOC
TP364
TP337TP336
MT5398_MISTRT
TP348
TP312
SC_L_IN_SOC
TP368
MT5398_TS_IN[1]
SCART_Lout_SOC
TP369
TP351
TP370
TP329
TP359
TP322
TP315
K4B4G1646B-HCK0IC701
DDR_512M_SS
A0N3
A1P7
A2P3
A3N2
A4P8
A5P2
A6R8
A7R2
A8T8
A9R3
A10/APL7
A11R7
A12/BCN7
A13T3
A15M7
BA0M2
BA1N8
BA2M3
CKJ7
CKK7
CKEK9
CSL2
ODTK1
RASJ3
CASK3
WEL3
RESETT2
DQSLF3
DQSLG3
DQSUC7
DQSUB7
DMLE7
DMUD3
DQL0E3
DQL1F7
DQL2F2
DQL3F8
DQL4H3
DQL5H8
DQL6G2
DQL7H7
DQU0D7
DQU1C3
DQU2C8
DQU3C2
DQU4A7
DQU5A2
DQU6B8
DQU7A3
VREFCAM8
VREFDQH1
ZQL8
VDD_1B2
VDD_2D9
VDD_3G7
VDD_4K2
VDD_5K8
VDD_6N1
VDD_7N9
VDD_8R1
VDD_9R9
VDDQ_1A1
VDDQ_2A8
VDDQ_3C1
VDDQ_4C9
VDDQ_5D2
VDDQ_6E9
VDDQ_7F1
VDDQ_8H2
VDDQ_9H9
NC_1J1
NC_2J9
NC_3L1
NC_4L9
A14T7
VSS_1A9
VSS_2B3
VSS_3E1
VSS_4G8
VSS_5J2
VSS_6J8
VSS_7M1
VSS_8M9
VSS_9P1
VSS_10P9
VSS_11T1
VSS_12T9
VSSQ_1B1
VSSQ_2B9
VSSQ_3D1
VSSQ_4D8
VSSQ_5E2
VSSQ_6E8
VSSQ_7F9
VSSQ_8G1
VSSQ_9G9
K4B4G1646B-HCK0IC703
DDR_512M_SS
A0N3
A1P7
A2P3
A3N2
A4P8
A5P2
A6R8
A7R2
A8T8
A9R3
A10/APL7
A11R7
A12/BCN7
A13T3
A15M7
BA0M2
BA1N8
BA2M3
CKJ7
CKK7
CKEK9
CSL2
ODTK1
RASJ3
CASK3
WEL3
RESETT2
DQSLF3
DQSLG3
DQSUC7
DQSUB7
DMLE7
DMUD3
DQL0E3
DQL1F7
DQL2F2
DQL3F8
DQL4H3
DQL5H8
DQL6G2
DQL7H7
DQU0D7
DQU1C3
DQU2C8
DQU3C2
DQU4A7
DQU5A2
DQU6B8
DQU7A3
VREFCAM8
VREFDQH1
ZQL8
VDD_1B2
VDD_2D9
VDD_3G7
VDD_4K2
VDD_5K8
VDD_6N1
VDD_7N9
VDD_8R1
VDD_9R9
VDDQ_1A1
VDDQ_2A8
VDDQ_3C1
VDDQ_4C9
VDDQ_5D2
VDDQ_6E9
VDDQ_7F1
VDDQ_8H2
VDDQ_9H9
NC_1J1
NC_2J9
NC_3L1
NC_4L9
A14T7
VSS_1A9
VSS_2B3
VSS_3E1
VSS_4G8
VSS_5J2
VSS_6J8
VSS_7M1
VSS_8M9
VSS_9P1
VSS_10P9
VSS_11T1
VSS_12T9
VSSQ_1B1
VSSQ_2B9
VSSQ_3D1
VSSQ_4D8
VSSQ_5E2
VSSQ_6E8
VSSQ_7F9
VSSQ_8G1
VSSQ_9G9
IC105LGE2122[A2_M13]
VCCK_1L11
VCCK_2N12
VCCK_3P12
VCCK_4AG5
VCCK_5AH5
VCCK_6AJ5
VCCK_7AK5
VCCK_8AL5
VCCK_9AM5
VCCK_10AN5
VCCK_11AK6
VCCK_12AL6
VCCK_13AM6
VCCK_14AN6
VCCK_15M11
VCCK_16N11
VCCK_17P11
VCCK_18R11
VCCK_19M12
VCCK_20R12
VCCK_21L13
VCCK_22L14
VCCK_23L15
VCCK_24L17
VCCK_25L18
VCCK_26L19
VCCK_27T11
VCCK_28U11
VCCK_29V11
VCCK_30W11
VCCK_31Y11
VCCK_32AA11
VCCK_33AB11
VCCK_34AC11
VCCK_35R23
VCCK_36L12
VCCK_37W12
VCCK_38V23
VCCK_39Y12
VCCK_40AF6
VCCK_41AG6
VCCK_42AH6
VCCK_43AJ6
VCCK_44AE7
VCCK_45AF7
VCCK_46AG7
VCCK_47AD8
VCCK_48AE8
VCCK_49AF8
VCCK_50AE9
VCCK_51AC10
VCCK_52AD10
VCCK_53AD11
VCCK_54AE10
VCCK_55AF9
VCCK_56AG8
VCCK_57AH7
VCCK_58AJ7
VCCK_59AK7
VCCK_60AL7
VCCK_61AM7
VCCK_62AN7
VCCK_63L16
VCCK_64V12
VCCK_65U12
VCCK_66T12
VCCK_67AD13
VCCK_68AD17
VCCK_69AD14
VCCK_70AB12
VCCK_71AA12
VCCK_72AC12
VCC3IO_CT9
VCC3IO_B_1Y10
VCC3IO_B_2AA10
VCC3IO_A_1D22
VCC3IO_A_2E22
DVSS_1AC18
DVSS_2AB21
DVSS_3AB14
DVSS_4N13
DVSS_5P13
DVSS_6R13
DVSS_7T13
DVSS_8U13
DVSS_9V13
DVSS_10W13
DVSS_11Y13
DVSS_12P18
DVSS_13N14
DVSS_14P14
DVSS_15R14
DVSS_16T14
DVSS_17U14
DVSS_18V14
DVSS_19W14
DVSS_20Y14
DVSS_21R18
DVSS_22N15
DVSS_23P15
DVSS_24R15
DVSS_25T15
DVSS_26U15
DVSS_27V15
DVSS_28W15
DVSS_29Y15
DVSS_30AA15
DVSS_31AB15
DVSS_32T18
DVSS_33R16
DVSS_34T16
DVSS_35U16
DVSS_36V16
DVSS_37W16
DVSS_38Y16
DVSS_39AA16
DVSS_40AB16
DVSS_41R17
DVSS_42T17
DVSS_43U17
DVSS_44V17
DVSS_45Y17
DVSS_46N16
DVSS_47V18
DVSS_48Y18
DVSS_49P16
DVSS_50V19
DVSS_51Y19
DVSS_52W17
DVSS_53AA17
DVSS_54AB17
DVSS_55N19
DVSS_56AC14
DVSS_57C13
DVSS_58K24
DVSS_59K25
DVSS_60L24
DVSS_61M17
DVSS_62M18
DVSS_63M19
DVSS_64P17
DVSS_65P19
DVSS_66N18
DVSS_67U20
DVSS_68V20
DVSS_69W20
DVSS_70Y20
DVSS_71AA20
DVSS_72R19
DVSS_73T19
DVSS_74M20
DVSS_75N20
DVSS_76U21
DVSS_77V21
DVSS_78W21
DVSS_79Y21
DVSS_80AA21
DVSS_81P20
DVSS_82R20
DVSS_83T20
DVSS_84U22
DVSS_85V22
DVSS_86W22
DVSS_87Y22
DVSS_88AA22
DVSS_89N21
DVSS_90P21
DVSS_91R21
DVSS_92T21
DVSS_93M22
DVSS_94N22
DVSS_95P22
DVSS_96R22
DVSS_97T22
DVSS_98M21
DVSS_99AC17
DVSS_100AA19
DVSS_101M13
DVSS_102M14
DVSS_103M15
DVSS_104AA13
DVSS_105AB13
DVSS_106AA14
DVSS_107AB19
DVSS_108D6
DVSS_109W19
DVSS_110U19
DVSS_111N17
DVSS_112L3
DVSS_113AB18
DVSS_114AA18
DVSS_115W18
DVSS_116U18
DVSS_117D16
DVSS_118AC13
DVSS_119M16
DVSS_120AC20
DVSS_121AC22
DVSS_122AD20
DVSS_123Y23
DVSS_124AA23
DVSS_125AB23
DVSS_126V24
DVSS_127W23
IC105LGE2122[A2_M13]
RVREF_CC2
BRCLK0J2
BRCLK0J1
BRCKEL6
BRODTE3
BRRASL4
BRCASD3
BRCSD4
BRBA0J4
BRBA1M6
BRBA2E4
BRWEK4
BRA15J3
BRA14P4
BRA13G5
BRA12P6
BRA11P5
BRA10L5
BRA9F4
BRA8P3
BRA7H4
BRA6P2
BRA5K6
BRA4M5
BRA3K5
BRA2G6
BRA1N5
BRA0E5
DDRV_12B19
DDRV_13C19
DDRV_14D19
DDRV_15E19
DDRV_16F19
DDRV_17G19
DDRV_18F5
DDRV_19H5
DDRV_20N8
DDRV_21P8
DDRV_22D13
DDRV_23E8
DDRV_24G11
DDRV_25D20
DDRV_26E20
DDRV_27F20
DDRV_28G20
DDRV_29R7
DDRV_30R8
DDRV_31T5
DDRV_32T6
DDRV_33T7
DDRV_34T8
BRDQM0L1
BRDQS0H2
BRDQS0H1
BRDQ0E2
BRDQ1N3
BRDQ2E1
BRDQ3N1
BRDQ4D1
BRDQ5P1
BRDQ6D2
BRDQ7N2
BRDQM1H3
BRDQS1K1
BRDQS1K2
BRDQ8N4
BRDQ9F2
BRDQ10M3
BRDQ11F1
BRDQ12L2
BRDQ13F3
BRDQ14M4
BRDQ15G3
BRRESETG4
IC105LGE2122[A2_M13]
DDRV_1R1
DDRV_2R2
DDRV_3R3
DDRV_4R4
DDRV_5R5
DDRV_6K3
DDRV_7R6
DDRV_8L8
DDRV_9M8
DDRV_10D17
DDRV_11A19
MEMTPJ22
MEMTNK22
RVREF_AD18
ARCKEG8
ARCLK1B5
ARCLK1A5
ARCLK0B14
ARCLK0A14
ARODTF13
ARRASE13
ARCASG13
ARCSG15
ARWEH18
ARRESETG16
ARBA0D15
ARBA1F9
ARBA2G18
ARCSXF15
ARA14D11
ARA13F16
ARA12D8
ARA11E11
ARA10G9
ARA9E16
ARA8F11
ARAG17
ARA6F10
ARA5E17
ARA4E10
ARA3E15
ARA2F17
ARA1G10
ARA0F18
ARDQM0D12
ARDQS0D14
ARDQS0C14
ARDQ0B17
ARDQ1D10
ARDQ2C17
ARDQ3C10
ARDQ4C18
ARDQ5B9
ARDQ6E18
ARDQ7D9
ARDQM1C15
ARDQS1A13
ARDQS1B13
ARDQ8B11
ARDQ9B16
ARDQ10A11
ARDQ11A17
ARDQ12C12
ARDQ13A16
ARDQ14C11
ARDQ15C16
ARDQM2A3
ARDQS2D5
ARDQS2C5
ARDQ16E7
ARDQ17B2
ARDQ18C8
ARDQ19B1
ARDQ20A9
ARDQ21C1
ARDQ22C9
ARDQ23C3
ARDQM3C6
ARDQS3A4
ARDQS3B4
ARDQ24A1
ARDQ25B7
ARDQ26C4
ARDQ27C7
ARDQ28B3
ARDQ29A7
ARDQ30A2
ARDQ31D7
AVDD33_MEMPLLA20
AVSS33_MEMPLLH9
R
5
0
1
1
.
8
K
WOL_CTL
+3.5V_ST
C5014.7uF10V
C5020.1uF16V
R50010K Q500
MMBT3904(NXP)
E
B
C
+3.5V_ST_WAKE
C5004.7uF10VOPT
Z
D
5
0
0
5
V
O
P
T
R
5
0
2
1
0
K
Q501PMV48XP
G
DS
AVDD_33SB
C5121uF10V
+3.5V_ST_WAKE
C5100.1uF16V
IC500AP2121N-3.3TRE1
1GND
2 VOUT3VIN
C5230.1uF
VDD3V3+1.2V_MTK_CORE
T
P
5
0
3
T
P
5
0
2
K4B2G1646E-BCK0 IC702-*1
DDR_256MB_SS
A0N3
A1P7
A2P3
A3N2
A4P8
A5P2
A6R8
A7R2
A8T8
A9R3
A10/APL7
A11R7
A12/BCN7
A13T3
NC_5M7
BA0M2
BA1N8
BA2M3
CKJ7
CKK7
CKEK9
CSL2
ODTK1
RASJ3
CASK3
WEL3
RESETT2
DQSLF3
DQSLG3
DQSUC7
DQSUB7
DMLE7
DMUD3
DQL0E3
DQL1F7
DQL2F2
DQL3F8
DQL4H3
DQL5H8
DQL6G2
DQL7H7
DQU0D7
DQU1C3
DQU2C8
DQU3C2
DQU4A7
DQU5A2
DQU6B8
DQU7A3
VREFCAM8
VREFDQH1
ZQL8
VDD_1B2
VDD_2D9
VDD_3G7
VDD_4K2
VDD_5K8
VDD_6N1
VDD_7N9
VDD_8R1
VDD_9R9
VDDQ_1A1
VDDQ_2A8
VDDQ_3C1
VDDQ_4C9
VDDQ_5D2
VDDQ_6E9
VDDQ_7F1
VDDQ_8H2
VDDQ_9H9
NC_1J1
NC_2J9
NC_3L1
NC_4L9
NC_6T7
VSS_1A9
VSS_2B3
VSS_3E1
VSS_4G8
VSS_5J2
VSS_6J8
VSS_7M1
VSS_8M9
VSS_9P1
VSS_10P9
VSS_11T1
VSS_12T9
VSSQ_1B1
VSSQ_2B9
VSSQ_3D1
VSSQ_4D8
VSSQ_5E2
VSSQ_6E8
VSSQ_7F9
VSSQ_8G1
VSSQ_9G9
H5TQ2G63DFR-PBC IC702-*2
DDR_256MB_HYNIX
A0N3
A1P7
A2P3
A3N2
A4P8
A5P2
A6R8
A7R2
A8T8
A9R3
A10/APL7
A11R7
A12/BCN7
A13T3
NC_5M7
BA0M2
BA1N8
BA2M3
CKJ7
CKK7
CKEK9
CSL2
ODTK1
RASJ3
CASK3
WEL3
RESETT2
DQSLF3
DQSLG3
DQSUC7
DQSUB7
DMLE7
DMUD3
DQL0E3
DQL1F7
DQL2F2
DQL3F8
DQL4H3
DQL5H8
DQL6G2
DQL7H7
DQU0D7
DQU1C3
DQU2C8
DQU3C2
DQU4A7
DQU5A2
DQU6B8
DQU7A3
VREFCAM8
VREFDQH1
ZQL8
VDD_1B2
VDD_2D9
VDD_3G7
VDD_4K2
VDD_5K8
VDD_6N1
VDD_7N9
VDD_8R1
VDD_9R9
VDDQ_1A1
VDDQ_2A8
VDDQ_3C1
VDDQ_4C9
VDDQ_5D2
VDDQ_6E9
VDDQ_7F1
VDDQ_8H2
VDDQ_9H9
NC_1J1
NC_2J9
NC_3L1
NC_4L9
NC_6T7
VSS_1A9
VSS_2B3
VSS_3E1
VSS_4G8
VSS_5J2
VSS_6J8
VSS_7M1
VSS_8M9
VSS_9P1
VSS_10P9
VSS_11T1
VSS_12T9
VSSQ_1B1
VSSQ_2B9
VSSQ_3D1
VSSQ_4D8
VSSQ_5E2
VSSQ_6E8
VSSQ_7F9
VSSQ_8G1
VSSQ_9G9
MT41K128M16JT-125:KIC703-*3
DDR_256MB_MICRON
A0N3
A1P7
A2P3
A3N2
A4P8
A5P2
A6R8
A7R2
A8T8
A9R3
A10/APL7
A11R7
A12/BCN7
A13T3
NC_5M7
BA0M2
BA1N8
BA2M3
CKJ7
CKK7
CKEK9
CSL2
ODTK1
RASJ3
CASK3
WEL3
RESETT2
DQSLF3
DQSLG3
DQSUC7
DQSUB7
DMLE7
DMUD3
DQ0E3
DQ1F7
DQ2F2
DQ3F8
DQ4H3
DQ5H8
DQ6G2
DQ7H7
DQ8D7
DQ9C3
DQ10C8
DQ11C2
DQ12A7
DQ13A2
DQ14B8
DQ15A3
VREFCAM8
VREFDQH1
ZQL8
VDD_1B2
VDD_2D9
VDD_3G7
VDD_4K2
VDD_5K8
VDD_6N1
VDD_7N9
VDD_8R1
VDD_9R9
VDDQ_1A1
VDDQ_2A8
VDDQ_3C1
VDDQ_4C9
VDDQ_5D2
VDDQ_6E9
VDDQ_7F1
VDDQ_8H2
VDDQ_9H9
NC_1J1
NC_2J9
NC_3L1
NC_4L9
NC_6T7
VSS_1A9
VSS_2B3
VSS_3E1
VSS_4G8
VSS_5J2
VSS_6J8
VSS_7M1
VSS_8M9
VSS_9P1
VSS_10P9
VSS_11T1
VSS_12T9
VSSQ_1B1
VSSQ_2B9
VSSQ_3D1
VSSQ_4D8
VSSQ_5E2
VSSQ_6E8
VSSQ_7F9
VSSQ_8G1
VSSQ_9G