36
Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and the concept of Roche lobe 3. Roche lobe radius calculation 4. Lagrange points and their stability 5. Hill problem and Hill stability

Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Embed Size (px)

Citation preview

Page 1: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Lecture 08 - ASTC25 Elements of Celestial Mechanics

Part 2 INTEGRALS OF MOTION

1. Energy methods (integrals of motion)2. Zero Vel. Surfaces (Curves) and the concept of Roche lobe 3. Roche lobe radius calculation4. Lagrange points and their stability5. Hill problem and Hill stability of orbits 6. Resonances and stability of the Solar System

Page 2: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Non-perturbative methods(energy constraints, integrals ofmotion)

Karl Gustav Jacob Jacobi (1804-1851)

Page 3: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

A standard trickto obtain energy integral

Solar sail problem again

Page 4: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and
Page 5: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Energy criterion guarantees that a particle cannot cross theZero Velocity Curve (or surface), and therefore is stablein the Jacobi sense (energetically).

However, remember that this is particular definition of stabilitywhich allows the particle to physically collide with the massivebody or bodies -- only the escape from the allowed region is forbidden! In our case, substituting v=0 into Jacobi constant,we obtain:

Page 6: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

f=0 f=0.051 < (1/16)

f=0.063 > (1/16) f=0.125

Allowed regions of motion in solar wind (hatched) lie within the Zero Velocity Curve

particle cannotescape from theplanet located at(0,0)

particle can (butdoesn’t always do!)escape from theplanet(cf. numerical cases B and C, wheref=0.134, and 0.2, much above the limit of f=1/16).

Page 7: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Circular Restricted 3-Body Problem (R3B)

L1

L4

L5

L3 L2

“Restricted” because the gravity of particle moving around thetwo massive bodies is neglected (so it’s a 2-Body problem plus 1 massless particle, not shown in the figure.) Furthermore, a circular motion of two massive bodies is assumed.

General 3-body problem has no known closed-form (analytical) solution.

Joseph-Louis Lagrange (1736-1813)[born: Giuseppe Lodovico Lagrangia]

Page 8: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

NOTES:The derivation of energy (Jacobi) integral in R3B does not differsignificantly from the analogous derivation of energy conservation law in the inertial frame, e.g., we also form thedot product of the equations of motion with velocity and convert the l.h.s. to full time derivative of specific kinetic energy.

On the r.h.s., however, we now have two additional accelerations (Coriolis and centrifugal terms) due to frame rotation (non-inertial,accelerated frame). However, the dot product of velocity and theCoriolis term, itself a vector perpendicular to velocity, vanishes.

The centrifugal term can be written as a gradient of a ‘centrifugal potential’ -(1/2)n^2 r^2, which added to the usual sum of -1/r gravitational potentials of two bodies, forms an effective potential Phi_eff. Notice that, for historical reasons, the effective R3B potential is defined as positive, that is, Phi_eff is the sum of two +1/r terms and +(n^2/2)r^2

Page 9: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

n

Page 10: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Effective potential in R3B mass ratio = 0.2

The effective potential of R3B is defined as negative of the usual Jacobi energy integral. The gravitational potential wells around the two bodies thus appear as chimneys.

Page 11: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Lagrange points L1…L5 are equilibrium points in the circularR3B problem, which is formulated in the frame corotating withthe binary system. Acceleration and velocity both equal 0 there.

They are found at zero-gradient points of the effective potential of R3B. Two of them are triangular points (extrema of potential). Three co-linear Lagrange points are saddle points of potential.

Page 12: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

rL = Roche lobe radius

+ Lagrange points

Jacobi integral and the topology of Zero Velocity Curves in R3B)/( 211 mmm

Page 13: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Sequence of allowed regions of motion (hatched) for particles starting with different C values (essentially, Jacobi constant ~ energy in corotating frame)

Highest C

Medium C

High C (e.g., particle starts close to one of the massive bodies)

Low C (for instance, due to high init. velocity)

Notice a curious fact:regions near L4 & L5

are forbidden. Theseare potential maxima(taking a physical, negativegravity potential sign)

Page 14: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Édouard Roche (1820–1883),

Roche lobes

terminology:

Roche lobe ~

Hill sphere ~

sphere of influence

(not really a sphere)

)/( 211 mmm = 0.1

C = R3B Jacobi constant with v=0

Page 15: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and
Page 16: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and
Page 17: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Stability around the L-points

Page 18: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Is the motion around Lagrange points stable?

Stability of motion near L-points can be studied in the 1st order perturbation theory (with unperturbed motion being state of rest at equilibrium point).

Page 19: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Stability of Lagrange points

Although the L1, L2, and L3 points are nominally unstable, it turns out that it is possible to find stable and nearly-stableperiodic orbits around these points in the R3B problem.They are used in the Sun-Earth and Earth-Moon systems forspace missions parked in the vicinity of these L-points.

By contrast, despite being the maxima of effective potential,

L4 and L5 are stable equilibria, provided M1/M2 is > 24.96 (as in Sun-Earth, Sun-Jupiter, and Earth-Moon cases).When a body at these points is perturbed, it moves away from the point, but the Coriolis force then bends the trajectory into a stable orbit around the point.

Page 20: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

From: Solar System Dynamics, C.D. Murray and S.F.Dermott, CUP

Observational proof of the stability of triangular equilibriumpoints

Greeks, L4

Trojans, L5

Page 21: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

= 0.1

= 0.01

)/( 211 mmm

)/( 211 mmm

Roche lobe radius depends weakly on R3B mass parameter

Page 22: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Computation of Roche lobe radius from R3B equationsof motion ( , a = semi-major axis of the binary)

L

ax /

Page 23: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

= 0.1

= 0.01

)/( 211 mmm

)/( 211 mmm

Roche lobe radius depends weakly on R3B mass parameter

m2/M = 0.01 (Earth ~Moon) r_L = 0.15 am2/M = 0.003 (Sun- 3xJupiter) r_L = 0.10 am2/M = 0.001 (Sun-Jupiter) r_L = 0.07 am2/M = 0.000003 (Sun-Earth) r_L = 0.01 a

arL3/1

3 )(

Page 24: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

George W. Hill (1838-1914) - studied the small mass ratio

limit of in the R3B, now called the Hill problem. He ‘straightened’ the

azimuthal coordinate by replacing it with a local Cartesian coordinate y,

and replaced r with x. L1 and L2 points became equidistant from the planet.

Other L points actually disappeared, but that’s natural since they are not

local (Hill’s equations are simpler than R3B ones, but are good approximations

to R3B only locally!)

Roche lobe ~ Hill sphere ~ sphere of influence (not really a sphere, though)

arr LL3/1

3 )(

Hill problem

Page 25: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Hill applied his equations to the Sun-Earth-Moon problem, showingthat the Moon’s Jacobi constant C=3.0012 is larger than CL=3.0009 (value ofeffective potential at the L-point), which means that its Zero Velocity Surface lies inside its Hill sphere and no escape from the Earth is possible: the Moon is Hill-stable.However, this is not a strict proof of Moon’s eternal stability because:(1) circular orbit of the Earth was assumed (crucial for constancy of Jacobi’s C)(2) Moon was approximated as a massless body, like in R3B.(3) Energy constraints can never exclude the possibility of Moon-Earth collision

arr LL3/1

3 )(

Hill problem

Page 26: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

COMPARISON OF THEORIESFrom the example of Sun-Earth-Moon system we find that: integrals of motion guarantee no-escape from the allowedregions of motion for an infinite period of time, which is betterthan either the general or the special perturbation theory can do but only if the assumptions of the theory are satisfied, andthat’s difficult to achieve in practice we are usually only interested in time periods up to Hubble time. In late 1990s our computers and algorithms becamecapable of simulating such enormous time spans. Numerical exploration has supplanted the elegant 18th-century methods as the preferred tool of dynamicists tryingto ascertain the stability of the Solar System and its exo-cousins.

(Laplace’s and Lagrange’s analytical methods were OK in their time, when the biblical age of the Sun/Earth of 4000 yr was accepted).

So….

Page 27: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Is the Solar System orbitally stable?…

Yes, it appears so (for billions of years),

but we cannot be absolutely sure!

Page 28: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Is the Solar System orbitally stable?… No certainty, now or ever.

The reason is that, like the weather on Earth, the detailed configuration of the planets after 1 Gyr, or even 100 mln yrs is impossible to predict or compute.

On Earth, this is because of chaos in weather systems (super-

sensistivity to initial conditions, too many coupled variables)

In planetary systems, chaos is due to planet-planet

gravitational perturbations amplified by resonances.

Two or more overlapping (weakened unexpectedly fast) resonances can make the precise

predictions of the future futile.

Hurricane Rita, Sept. 23, 2005

?

Page 29: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Double pendulum

Chaos in:

Lorentz attractor(modeled after weather system equations)

oscillation

rotation

Page 30: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

In the Solar System, resonant angles librate (oscillate)in 2-body resonances

Page 31: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Strong, non-chaotic resonances in satellite systemsAlso planets exhibit such low-order commensurabilities, the most famous being perhaps the 2:5 Saturn-Jupiter one. (2:3 Pluto-Neptuneresonance does not prevent chaotic nature of Pluto’s orbit.)

Page 32: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Example of chaotic orbits due to overlapping resonances

Page 33: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

Orbits and planet positions are unpredictable on a timescale of 100 mln yrs or less (50 mln yrs for Earth).

For instance, let the longitudes of perihelia be denoted by wand the ascending nodes as W, then using subscripts E and Mfor Earth and Mars, there exists a resonant angle fME = 2(wM -wE) - (WM -WE)that shows the same hesitating behavior between oscillation (libration) and circulation (when resonant lock is broken) as in a double pendulum experiment.

But chaos in our system is stable for the time ~ its age Orbits have the numerical, long-term, stability. They don’t crossand planets don’t exchange places or get ejected into Galaxy.

The only questionable stability case is that of Mercury & Sun.Mercury makes such wide excursions in orbital elements, that in some simulations it drops onto the Sun in 3-10 Gyr.

Page 34: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

How wide a region is destabilized by a planet?

Page 35: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

arr LL3/1

3 )(

Hill stability ofcircumstellar motion near the planet

The gravitational influence of a small body (a planet around a star, for instance) dominates the motion inside its Roche lobe, so particle orbitsthere are circling around the planet, not the star. The circumstellar orbits in thevicinity of the planet’s orbit are affected, too. Bodies on “disk orbits”(meaning the disk of bodies circling around the star) have Jacobi constants Cdepending on the orbital separation parameter x = (r-a)/a (r=initial circular orbitradius far from the planet, a = planet’s orbital radius). If |x| is large enough, the disk orbits are forbidden from approaching L1 and L2 and entering the Roche lobe by the energy constraint. Their effective energy is not enough to pass through the saddle point of the effective potential. Therefore, disk regions farther away than some minimum separation |x| (assuming circularinitial orbits) are guaranteed to be Hill-stable, which means they are isolatedfrom the planet.

CCL

Page 36: Lecture 08 - ASTC25 Elements of Celestial Mechanics Part 2 INTEGRALS OF MOTION 1. Energy methods (integrals of motion) 2. Zero Vel. Surfaces (Curves) and

2433 xC

2)/(93 arC LL 22 )/(12 arx L

ararx LL /5.3)/(32

24.0)3/001.0(5.3/5.3 3/1 arx L

CL

C

arL3/1

3 )(

Hill stability ofcircumstellarmotion near theplanet

On a circular orbit with x = (r-a)/a,

At the L1 and L2 points

Therefore, the Hill stability criterion C(x)=CL readsor

Example:

What is the extent of Hill-unstable region around Jupiter?

Since Jupiter is at a=5.2 AU, the outermost Hill-stable circular orbit is at r = a - xa = a - 0.24a = 3.95 AU. Asteroid belt objects are indeed found at r < ~4 AU (Thule group at ~4 AU is the outermost large group of asteroids except for Trojan and Greek asteroids)