Upload
eiintan-ieo
View
251
Download
1
Embed Size (px)
DESCRIPTION
lukisan kejuruteraan
Citation preview
RAJAH 1
BINA HELIX SEPERTI RAJAH 1Command: helix Number of turns = 3.0000 Twist=CCW
Specify center point of base: clik pada mana paparanSpecify base radius or [Diameter] : d Specify diameter : 12 Specify top radius or [Diameter] : d Specify diameter : 12 Specify helix height or [Axis endpoint/Turns/turn Height/tWist] : h Specify distance between turns : 3 Specify helix height or [Axis endpoint/Turns/turn Height/tWist] : t Enter number of turns : 43
RAJAH 2
BINA BOX PADA RAJAH 2
Command: line Specify first point: pada hujung helix (a)Specify next point or [Undo]: 0.5 Specify next point or [Undo]: 1
Specify next point or [Close/Undo]: 1
Specify next point or [Close/Undo]: 1
Specify next point or [Close/Undo]:
Specify next point or [Close/Undo]:
Command: region Select objects: clik pada semua garisan boxSelect objects: 1 loop extracted.
1 Region created.
RAJAH 3
BINA BENANG
Command: sweep Current wire frame density: ISOLINES=4
Select objects to sweep: clik pada kotak ( 1) Select sweep path or [Alignment/Base point/Scale/Twist]: clik pada helix (2)*tunggu hingga objek terbina seperti Rajah 4
RAJAH 4
Command: hide . (Rajah 5)
RAJAH 5
RAJAH 6
BINA SELINDER 130mm (Rajah 6)
Command: c CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: clik pada (b)Specify radius of circle or [Diameter]: d Specify diameter of circle : 14
Command: extrude
Select objects to extrude: clik pada circle (c)Specify height of extrusion or [Direction/Path/Taper angle]: 130 *terhasil seperti Rajah 7
RAJAH 7
RAJAH 8
Command: union Select objects: clik pada (d)Select objects: clik pada (e)Select objects:
Command: hide . (Rajah 9)
RAJAH 9
RAJAH 10Bina selinder lebih besar untuk memotong bebenang
Command: c CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: clik pada (f)Specify radius of circle or [Diameter] : d Specify diameter of circle : 20
RAJAH 11Command: extrude Select objects to extrude: Clik pada (g) pada Rajah 11Specify height of extrusion or [Direction/Path/Taper angle] : 1
RAJAH 12Command: copy Select objects: 1 found
Select objects: clik pada (h) pada Rajah 12Specify base point or [Displacement/mOde/Multiple] : di atas seperti (i)Specify second point or :
Command: copy
Select objects: 1 found
Select objects:
Current settings: Copy mode = Single
Specify base point or [Displacement/mOde/Multiple] : _qua of
Specify second point or : _qua of
Command: COPY Select objects: 1 found
Select objects: clik pada (h) pada Rajah 12
Specify base point or [Displacement/mOde/Multiple] : di atas seperti (j)
Current settings: Copy mode = Single
Specify base point or [Displacement/mOde/Multiple] : _qua of
Specify second point or : _qua of
Command: *Cancel*
RAJAH 13
Command: union Select objects: clik pada h,i,j pada semua selinder pd Rajah 12Select objects:
RAJAH 14
Command: subtract
Select objects: clik pada (k) pada Rajah 12Select objects: clik pada (l) pada Rajah 12Select objects: *akan terhasil seperti Rajah 14
Command: hide . (Rajah 15)
RAJAH 151
2
a
b
c
d
e
f
g
h
i
j
k
l