Lab Report

UNIVERSITI TEKNOLOGI MARA

FACULTY OF ELECTRICAL ENGINEERING

INTERNET PROTOCOLECE734

PREPARED BY:

MAHATHIR BIN JOHAR

ID NUMBER:

2009241034

PREPARED FOR

DR MAT IKRAM YUSOF

Chapter 3 Lab 3-7, OSPF Case Study Topology

Objectives • Plan, design, and implement the International Travel Agency network shown in the diagram and described below. • Verify that all configurations are operational and functioning according to the guidelines.

Note: This lab uses Cisco 1841 routers with Cisco IOS Release 12.4(24)T1 and the Advanced IP Services image c1841-advipservicesk9-mz.124-24.T1.bin. You can use other routers (such as a 2801 or 2811) and Cisco IOS Software versions if they have comparable capabilities and features. Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab.

Required Resources • 4 routers (Cisco 1841 with Cisco IOS Release 12.4(24)T1 Advanced IP Service or comparable) • Serial and console cables

Requirements The International Travel Agency needs its core network set up for OSPF with the specifications indicated in the diagram and listed below. Design, configure, and test a network that meets all the following requirements:

1. Use the addressing scheme shown in the diagram. 2. Configure OSPF with the networks shown in the diagram. 3. Configure the OSPF backbone area to be on Loopback0 on HQ. 4. Configure the Frame Relay subnets as point-to-point subinterfaces, with the link between HQ and East in area 100, and the link between HQ and West in area 300. 5. Configure area 300 as an NSSA. 6. Configure the router East loopback interfaces to be in area 200. Summarize this area with the most efficient summary. 7. Redistribute the loopback network on router West into OSPF. 8. Create virtual links as necessary for full connectivity.

9. Make sure that all loopback interfaces are advertised with the correct subnet mask. # Lab 3-7 OSPF Case Study# By :Dr Mat IkramYusof CCNP,CCSP,CCNA,CCAI,SCNA,SCSA,SCJP,ITILF################################################################## To get available chassis and NM, run "dynamips -H 7200 &dynamips -H 7201 &" from# the command line in the dynamipsdirectory.And " dynagen Lab1-0"## Available C3600 chassis drivers:# * 3620# * 3640# * 3660################################################################## Available C3600 Network Module drivers:# * NM-1E# * NM-4E# * NM-1FE-TX# * NM-4T# * Leopard-2FE# * NM-16ESW#################################################################

mmap = trueghostios = Truesparsemem = Trueautostart = False

[localhost:7200]

#workingdir = C:\Program Files\Dynamips\sample_labs\internetworkexpert\workingworkingdir = C:\Program Files (x86)\Dynamips\sample_labs\ccnp1Labs\OSPF\Lab3-8\working

[[3640]] # # Specify 3640 IOS image on Windows here: #image = C:\Program Files\Dynamips\images\c3640-jk9o3s-mz.123-14.T7.extracted.bin # # Specify 3640 IOS image on Linux here: # image = /ios/c3640-jk9o3s-mz.123-14.T7.extracted.binimage = C:\Program Files (x86)\Dynamips\images\c3640-jk9o3s-mz.124-5a.bin #ram = 128 disk0 = 0 disk1 = 0 # Choose an idlepc value from the belowidlepc = 0x60610428

########################### # # Define router instances # ###########################

[[ROUTER FRS]]model = 3640console = 2009 slot1 = NM-4Ts1/0 = HQ s1/0s1/1 = East s1/0s1/2 = West s1/0

[[ROUTER West]]model = 3640console = 2012 slot1 = NM-4Ts1/0 = FRS s1/2

[[ROUTER HQ]]model = 3640console = 2011 slot1 = NM-4Ts1/0 = FRS s1/0

[[ROUTER East]]model = 3640console = 2010 slot1 = NM-4Ts1/0 = FRS s1/1

ROUTER 3(FRS) CONFIGURATION

FRS#sh run

Building configuration...

Current configuration : 1226 bytes

version 12.4

service timestamps debug datetimemsec

service timestamps log datetimemsec

no service password-encryption

hostname FRS

boot-start-marker

boot-end-marker

noaaa new-model

resource policy

memory-sizeiomem 5

ipcef

frame-relay switching

interface Serial1/0

noip address

encapsulation frame-relay

serial restart-delay 0

clock rate 64000

nodce-terminal-timing-enable

frame-relayintf-type dce

frame-relay route 102 interface Serial1/1 201


!

interface Serial1/1

noip address



clock rate 64000




!

interface Serial1/2

noip address



clock rate 64000




!

interface Serial1/3

noip address

shutdown



!

ip http server

noip http secure-server

control-plane

line con 0

line aux 0

linevty 0 4

!

End

ROUTER 1(HQ) CONFIGURATION

HQ#sh run



version 12.4




hostname HQ

boot-start-marker

boot-end-marker

no aaa new-model

resource policy

memory-sizeiomem 5

ipcef

!

interface Loopback1

ip address 10.1.1.9 255.255.255.252

ipospf network point-to-point

!

interface Serial1/0

noip address




!

interface Serial1/0.102 point-to-point

ip address 10.1.1.1 255.255.255.252

frame-relay interface-dlci 102

!


ip address 10.1.1.5 255.255.255.252


!

interface Serial1/1

noip address

shutdown



!

interface Serial1/2

noip address

shutdown



!

interface Serial1/3

noip address

shutdown



!

routerospf 1

log-adjacency-changes

area 100 virtual-link 10.1.1.113

area 300 nssa

network 10.1.1.0 0.0.0.3 area 100

network 10.1.1.4 0.0.0.3 area 300

network 10.1.1.8 0.0.0.3 area 0

!

ip http server

noip http secure-server

control-plane

line con 0

line aux 0

linevty 0 4

!

end

ROUTER 2(EAST) CONFIGURATION

EAST#sh run



version 12.4




hostname EAST

boot-start-marker

boot-end-marker

noaaa new-model

resource policy

memory-sizeiomem 5

ipcef

interface Loopback101

ip address 10.1.1.101 255.255.255.252


!


ip address 10.1.1.105 255.255.255.252


!


ip address 10.1.1.109 255.255.255.252


!


ip address 10.1.1.113 255.255.255.252


!

interface Serial1/0

noip address




!


ip address 10.1.1.2 255.255.255.252


!

interface Serial1/1

no ip address

shutdown


no dce-terminal-timing-enable

!

interface Serial1/2

no ip address

shutdown



!

interface Serial1/3

no ip address

shutdown



!

Router ospf 1


area 100 virtual-link 10.1.1.9

area 200 range 10.1.1.96 255.255.255.224

network 10.1.1.0 0.0.0.3 area 100

network 10.1.1.100 0.0.0.3 area 200

network 10.1.1.104 0.0.0.3 area 200

network 10.1.1.108 0.0.0.3 area 200

network 10.1.1.112 0.0.0.3 area 200

!

ip http server

no ip http secure-server

control-plane

!

line con 0

line aux 0

line vty 0 4

!

!

End

ROUTER 4(WEST) CONFIGURATION

WEST#sh run



version 12.4

service timestamps debug date time msec

service timestamps log date time msec


hostname WEST

boot-start-marker

boot-end-marker

no aaa new-model

resource policy

memory-size iomem 5

ip cef

interface Loopback3

ip address 10.1.1.13 255.255.255.252

ip ospf network point-to-point

!

interface Serial1/0

no ip address




!


ip address 10.1.1.6 255.255.255.252


!

interface Serial1/1

no ip address

shutdown



!

interface Serial1/2

no ip address

shutdown



!

interface Serial1/3

no ip address

shutdown



!

Router ospf 1


area 300 nssa

redistribute connected subnets

network 10.1.1.4 0.0.0.3 area 300

ip http server


control-plane

line con 0

line aux 0

line vty 0 4

end

RESULT

WEST(tcl)#foreach address {

+>10.1.1.9

+>10.1.1.1

+>10.1.1.5

+>10.1.1.2

+>10.1.1.101

+>10.1.1.105

+>10.1.1.109

+>10.1.1.113

+>} {

+>ping $address }

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.1.1.9, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 56/110/224 ms



!!!!!




!!!!!




!!!!!




!!!!!




!!!!!




!!!!!




!!!!!


WEST#sh ip ospf neighbor

Neighbor ID Pri State Dead Time Address Interface

10.1.1.9 0 FULL/ - 00:00:35 10.1.1.5 Serial1/0.301

EAST#sh ip ospf neighbor


10.1.1.9 0 FULL/ - - 10.1.1.1 OSPF_VL0

10.1.1.9 0 FULL/ - 00:00:34 10.1.1.1 Serial1/0.201

HQ#sh ip ospf neighbor


10.1.1.113 0 FULL/ - - 10.1.1.2 OSPF_VL0

10.1.1.113 0 FULL/ - 00:00:37 10.1.1.2 Serial1/0.102

10.1.1.13 0 FULL/ - 00:00:32 10.1.1.6 Serial1/0.103

HQ#sh ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

ia - IS-IS inter area, * - candidate default, U - per-user static route

o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

10.0.0.0/8 is variably subnetted, 5 subnets, 2 masks

C 10.1.1.8/30 is directly connected, Loopback1

O N2 10.1.1.12/30 [110/20] via 10.1.1.6, 00:47:56, Serial1/0.103

C 10.1.1.0/30 is directly connected, Serial1/0.102


O IA 10.1.1.96/27 [110/65] via 10.1.1.2, 00:47:56, Serial1/0.102

EAST#sh ip route










O 10.1.1.8/30 [110/65] via 10.1.1.1, 00:48:37, Serial1/0.201

O E2 10.1.1.12/30 [110/20] via 10.1.1.1, 00:48:35, Serial1/0.201


O IA 10.1.1.4/30 [110/128] via 10.1.1.1, 00:48:37, Serial1/0.201



O 10.1.1.96/27 is a summary, 00:48:57, Null0



WEST#sh ip route










O IA 10.1.1.8/30 [110/65] via 10.1.1.5, 00:49:10, Serial1/0.301


O IA 10.1.1.0/30 [110/128] via 10.1.1.5, 00:49:10, Serial1/0.301


O IA 10.1.1.96/27 [110/129] via 10.1.1.5, 00:49:10, Serial1/0.301

LAB 8-4 : IPV6 CHALLENGE LAB

3

Objectives • Implement the topology diagram using the instructions in the Requirements section. • Change the IPv6 IGP from OSPFv3 to RIPng.

Background In the first part of this lab (Steps 1 through 7), you configure IPv4 with EIGRP on routers R1, R2 and R3. You also configure IPv6 with OSPFv3 on routers R1, R3 and R4, create an IPv6 tunnel between R1 and R3 and then test network connectivity. In the second part of the lab (Step 8), you replace the OSPFv3 routing protocol with RIPng and re-test connectivity.

Required Resources Note: This lab uses Cisco 1841 routers with Cisco IOS Release 12.4(24)T1 and the Advanced IP Services image c1841-advipservicesk9-mz.124-24.T1.bin. You can use other routers (such as a 2801 or 2811) and Cisco IOS Software versions if they have comparable capabilities and features. Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab. • 4 routers (Cisco 1841 with Cisco IOS Release 12.4(24)T1 Advanced IP Services or comparable) • Serial and console cables

Requirements 1. Configure all interfaces in the topology diagram with the IPv4 or IPv6 addresses shown.

2. Use EUI-64 addresses on the link between R3 and R4.

3. Configure EIGRP AS 1 on R1, R2, and R3 to route all IPv4 networks.

4. Disable EIGRP automatic summarization.

5. Configure a manual IPv6 tunnel between R1 and R3.

6. Include all IPv6 networks in OSPF area 0 on R1, R3, and R4.

7. Manually configure a router ID of 172.16.4.1 on R4 (this address does not need to be reachable).

8. Remove the OSPFv3 configuration commands from R1, R3, and R4 and configure RIPng to run on these routers using RIP1 as the process name.

# Lab 8-4 IPv6 Challenge Lab# By :Dr Mat IkramYusof CCNP,CCSP,CCNA,CCAI,SCNA,SCSA,SCJP,ITILF################################################################## To get available chassis and NM, run "dynamips -H 7200 &dynamips -H 7201 &" from# the command line in the dynamipsdirectory.And " dynagen Lab1-0"## Available C3600 chassis drivers:# * 3620# * 3640# * 3660################################################################## Available C3600 Network Module drivers:# * NM-1E# * NM-4E# * NM-1FE-TX# * NM-4T# * Leopard-2FE# * NM-16ESW#################################################################

mmap = trueghostios = Truesparsemem = Trueautostart = False

[localhost:7200]

#workingdir = C:\Program Files (x86)\Dynamips\sample_labs\internetworkexpert\workingworkingdir = C:\Program Files (x86)\Dynamips\sample_labs\ccnp1Labs\IPV6\working

[[3640]] # # Specify 3640 IOS image on Windows here: #image = C:\Program Files\Dynamips\images\c3640-jk9o3s-mz.123-14.T7.extracted.bin # # Specify 3640 IOS image on Linux here: # image = /ios/c3640-jk9o3s-mz.123-14.T7.extracted.binimage = C:\Program Files (x86)\Dynamips\images\c3640-jk9o3s-mz.124-5a.bin #ram = 128

disk0 = 0 disk1 = 0 # Choose an idlepc value from the belowidlepc = 0x60610428

########################### # # Define router instances # ###########################

[[ROUTER R1]]model = 3640console = 2001 slot0 = NM-4T

s0/0 = R2 s0/0

[[ROUTER R2]]model = 3640console = 2002 slot0 = NM-4T slot1 = NM-1FE-TX

s0/1 = R3 s0/1


s0/0 = R4 s0/0


R1 CONFIGURATION

R1#sh runBuilding configuration...

Current configuration : 1325 bytes!version 12.4service timestamps debug date time msecservice timestamps log date time msecno service password-encryption!hostname R1!boot-start-markerboot-end-marker!!No aaa new-model!resource policy!memory-size iomem 5!!Ip cef!

ipv6 unicast-routingipv6cef!

interface Tunnel0no ip addressipv6 address FEC::13:1/112ipv6 address FEC0::13:1/112ipv6 rip RIP1 enabletunnel source Serial0/0tunnel destination 172.16.23.3tunnel mode ipv6ip!interface Loopback0no ip addressipv6 address FEC0::1:1/112ipv6 rip RIP1 enable!interface Serial0/0bandwidth 64ip address 172.16.12.1 255.255.255.0serial restart-delay 0clock rate 64000

no dce-terminal-timing-enableno fair-queue!interface Serial0/1no ip addressshutdownserial restart-delay 0no dce-terminal-timing-enable!interface Serial0/2no ip addressshutdownserial restart-delay 0no dce-terminal-timing-enable!interface Serial0/3no ip addressshutdownserial restart-delay 0no dce-terminal-timing-enable!Route reigrp 1network 172.16.0.0no auto-summary!ip http serverno ip http secure-server!ipv6 router ospf 1log-adjacency-changes!ipv6 router rip RIP1!control-plane!line con 0line aux 0line vty 0 4login!!End

R2 CONFIGURATION

R2#sh runBuilding configuration...

Current configuration : 1055 bytes!version 12.4

service timestamps debug date time msecservice timestamps log date time msecno service password-encryption!hostname R2!boot-start-markerboot-end-marker!

No aaa new-model!resource policy!memory-size iomem 5!Ip cef!

interface Serial0/0bandwidth 64ip address 172.16.12.2 255.255.255.0serial restart-delay 0no dce-terminal-timing-enableno fair-queue!interface Serial0/1bandwidth 64ip address 172.16.23.2 255.255.255.0serial restart-delay 0clock rate 64000no dce-terminal-timing-enable!interface Serial0/2noip addressshutdownserial restart-delay 0no dce-terminal-timing-enable!interface Serial0/3no ip addressshutdownserial restart-delay 0no dce-terminal-timing-enable!interface FastEthernet1/0no ip addressshutdownduplex autospeed auto!

Route reigrp 1network 172.16.0.0no auto-summary!ip http serverno ip http secure-server!control-plane!line con 0line aux 0line vty 0 4login

endR3 CONFIGURATION

R3#sh run



version 12.4




!

hostname R3

!

boot-start-marker

boot-end-marker

no aaa new-model

resource policy

memory-size iomem 5

ip cef

ipv6 unicast-routing

ipv6cef

!

interface Tunnel0

no ip address

ipv6 address FEC0::13:3/112

ipv6 rip RIP1 enable

tunnel source Serial0/1

tunnel destination 172.16.12.1

tunnel mode ipv6ip

!

interface Loopback0

no ip address



!

interface Serial0/0

bandwidth 64

no ip address

ipv6 address FEC0:34::/64 eui-64



clock rate 64000


no fair-queue

!

interface Serial0/1

bandwidth 64

ip address 172.16.23.3 255.255.255.0



!

interface Serial0/2

no ip address

shutdown



!

interface Serial0/3

no ip address

shutdown



!

interface FastEthernet1/0

no ip address

shutdown

duplex auto

speed auto

!

Router eigrp 1

network 172.16.0.0

no auto-summary

!

ip http server


!

ipv6 router ospf 1


!

ipv6 router rip RIP1

!

control-plane

!

line con 0

line aux 0

line vty 0 4

login

!

!

end

R4 CONFIGURATION

R4#sh run



version 12.4




hostname R4

boot-start-marker

boot-end-marker

no aaa new-model

resource policy

memory-size iomem 5

ip cef

ipv6 unicast-routing

ipv6cef

!

interface Loopback0

no ip address



!

interface Serial0/0

bandwidth 64

no ip address

ipv6 address FEC0:34::/64 eui-64




no fair-queue

!

interface Serial0/1

no ip address

shutdown



!

interface Serial0/2

no ip address

shutdown



!

interface Serial0/3

no ip address

shutdown



!

interface FastEthernet1/0

no ip address

shutdown

duplex auto

speed auto

!

ip http server


!

ipv6 router ospf 1

router-id 172.16.4.1


!

ipv6 router rip RIP1

!

control-plane

!

line con 0

line aux 0

line vty 0 4

login

!

!

End

--------------------------------------------------------------------------------------------------------------------------------------

RESULT

R1#tclsh

R1(tcl)#foreach address {

+>(tcl)#172.16.12.2

+>(tcl)#172.16.23.2

+>(tcl)#172.16.23.3

+>(tcl)#FEC0::3:1

+>(tcl)#FEC0::4:1

+>(tcl)#} {

+>(tcl)#ping $address }



!!!!!




!!!!!




!!!!!



Sending 5, 100-byte ICMP Echos to FEC0::3:1, timeout is 2 seconds:

!!!!!



Sending 5, 100-byte ICMP Echos to FEC0::4:1, timeout is 2 seconds:

!!!!!


R1#sh ipv6 route

IPv6 Routing Table - 11 entries

Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP

U - Per-user Static route

I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary

O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2

ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2

C FEC::13:0/112 [0/0]

via ::, Tunnel0

L FEC::13:1/128 [0/0]

via ::, Tunnel0

L FE80::/10 [0/0]

via ::, Null0

C FEC0::1:0/112 [0/0]

via ::, Loopback0

L FEC0::1:1/128 [0/0]

via ::, Loopback0

R FEC0::3:0/112 [120/2]

via FE80::AC10:1703, Tunnel0

R FEC0::4:0/112 [120/3]


C FEC0::13:0/112 [0/0]

via ::, Tunnel0

L FEC0::13:1/128 [0/0]

via ::, Tunnel0

R FEC0:34::/64 [120/2]


L FF00::/8 [0/0]

via ::, Null0

R4#sh ipv6 int brief

Serial0/0 [up/up]

FE80::CE03:1AFF:FE24:10

FEC0:34::CE03:1AFF:FE24:10

Serial0/1 [administratively down/down]

unassigned


unassigned


unassigned

FastEthernet1/0 [administratively down/down]

unassigned

Loopback0 [up/up]

FE80::CE03:1AFF:FE24:10

FEC0::4:1

R1#ping FEC0:34::CE03:1AFF:FE24:10


Sending 5, 100-byte ICMP Echos to FEC0:34::CE03:1AFF:FE24:10, timeout is 2 seconds:

!!!!!


R3#sh ipv6 route

IPv6 Routing Table - 11 entries

Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP

U - Per-user Static route

I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary

O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2

ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2

R FEC::13:0/112 [120/2]

via FE80::AC10:C01, Tunnel0

L FE80::/10 [0/0]

via ::, Null0

R FEC0::1:0/112 [120/2]

via FE80::AC10:C01, Tunnel0

C FEC0::3:0/112 [0/0]

via ::, Loopback0

L FEC0::3:1/128 [0/0]

via ::, Loopback0

R FEC0::4:0/112 [120/2]

via FE80::CE03:1AFF:FE24:10, Serial0/0

C FEC0::13:0/112 [0/0]

via ::, Tunnel0

L FEC0::13:3/128 [0/0]

via ::, Tunnel0

C FEC0:34::/64 [0/0]

via ::, Serial0/0

L FEC0:34::CE02:1AFF:FE24:10/128 [0/0]

via ::, Serial0/0

L FF00::/8 [0/0]

via ::, Null0

Documents

Lab Report