ENV 1.0

User Guide

KV500/KV600

KV Series Rack Mount HDD/SSD Duplicator

3

Content IndexContent Index 3Disclaimer of Warranties 5Notice 5

1 IntroductionProduct Overview 6Features 7Hardware Overview 8

§ Appearance 8§ LCD Configuration 8§ How to Extend Targets 9

2 Function TableKV Series 10

3 Reminder⌘ Before You Start 12

4 How to Copy HDDs⌘ Start to Copy 13⌘ Setup before Copy/Compare 14 ❶ Set Copy Area of Source HDD 14 System and Files (Quick Copy, Quick Compare) 15 All Partition 15 Whole HDD 16 Percentage(%) 16 ❷ Set Tolerance of Bad Track 17

➌ Auto Skip Lower-Speed HDDs 17➍ Auto Skip Lower-Speed Source 18

⌘ Troubleshooting When DuplicationFails 18

5 How to Confirm Copy Accuracy?⌘ Compare Duplication Results 19⌘ Setting of Compare Function 19

6 How to Erase HDDs⌘ How to Erase Data 20⌘ Setting of Erase Function 21 ① Quick Erase 21 ② Full Erase 21 ③ DoD Erase 21 ④ DoD Erase Comp 22 ➊ Overwrite by fixed method 22 ➋ Overwrite by random

method 23 ⑤ Secure Erase 23

7 How to Update BIOS⌘ Update by BIOS HDD 24

8 How to Use PC-Monitoring1 Real-time PC Monitoring 25

⌘ Preparation before Start 25§ Installation 25§ Launch PC-Monitoring 27

⌘ Operation of PC-Monitoring 282 Log Report 29

⌘ Browse Log Report through PC 29§ Log Records & Screen 31

⌘ Advanced Function 32➊ Clear ALL Logs 32➋ Setup Password 32

FAQPC-Monitoring 33The Duplicator 34

SpecificationSpecification 35

5

Warranties & NoticeDisclaimer of WarrantiesAll duplicators are made specifically for data backup with legal authorities from copyright owners. Any unauthorized action of copyright is strictly prohibited, and the manufacturer disclaims all warranties or representations of illegal actions by users.The manufacturer also disclaims any liability for any loss or damage due to not being able to perform its undertakings or provide any of the services attributable to any events or circumstances beyond our control. Users agree and accept all statements above as soon as purchasing our products. This manual contains materials that should be intended for personal use, all right reserved. No part of this manual may be reproduced, transmitted or transcribed without the expressed written permission of the manufacturer. The information present in this manual is subject to change without prior notice.

Notice⌘ Important Notice• Read the complete operation instruction carefully contributes to better operation.• Make sure the source device is correct and workable.• To guarantee data consistency, we highly recommend the capacity of source

and targets should be the same.• It is strongly suggested to use "Copy&Compare" to achieve a perfect

duplication.

⌘ Safety Precautions• The warranty will expire if damage is incurred resulting from noncompliance with

theses operating instructions.• Store the equipment safely when not in used and keep out of the reach of

children and infants.• Please turn off the power before replace the socket.• Never turn off the power while processing the firmware update.• Use only approved power sources.• The product is only suitable for operation in dry, dust free, clean environment.

Do not allow liquids or foreign objects to enter. Failure to do so may severely damage your duplicator.

6

1 IntroductionProduct OverviewThis is a bulky and amazing easy expandable HDD/SSD Duplicator. When a KV500 was hook up with any other unit of KV500 or KV600, it will immediately become a machine with larger target ports. For example, when a KV500, a 4-target duplicator, link with a KV600 (6-target-port), within seconds, it become a 10 targets HDD duplicator. No need of any setup or software install, just so simple and easy.This HDD duplicator, KV series, is a high-end industrial standard hard disk duplicator that makes HDD duplication fast and easy. There is no computer or additional software required. Support high data transfer speed. The three different copy modes (System and Files, All Partition and Whole HDD) can satisfy various needs of duplication

7

Introduction 1FeaturesFlexibility to expand target without slowing down speed Just a simple hookup to link each single unit together to easily expand the machine targets

Rack Mount Enclosure DesignFirm for use. Easy to install and expand the machine by piling up all the duplicators in a server cabinet.

Ultra High Speed Ultra high speed based on real testing.

Extendable Productivity It can easily like by daisy chain technology. User can either use it as 1 to 4 or link up to 1 to 254 targets.

Auto Power Control SystemProtect the HDD from damage during removal from the duplicator.

Quick Copy ModeThis mode can identify the HDD formats of FAT, NTFS, Mac(HFS, HFX, HFS+)and Linux. It will only copy the data and system contained area, which can highly enhance the copying efficiency.

Support Multi-Interface Duplicator supports 2.5"/3.5" SATA interface directly and support CRU interface via adaptor.

Four Erase MethodsQuick Erase, Full Erase, DoD Erase, and Secure Erase.

Four Kinds of Copy ModesThe four different copy modes to meet different work situation needs, Systems and Files, All Partition, Whole HDD, Percentage Copy.

8

1 IntroductionHardware Overview§ Appearance

Operation buttons

SATA module interface

Source port

Indication LED

LCD

Front view

§ LCD Configuration

FunctionNumber oftarget HDD Total size Forward Confirm/OK

Time elapsed andcopy progress

Copied processed size

Port # of the slowestcopying HDD

Backward Cancel/Back

9

Introduction 1§ How to Extend Targets

☉ Using internal cable links up to 254 ports. ☉ The first tower of the linkage controls the operation.

The Third Tower

The Second Tower

The First Tower

10

2 Function TableKV SeriesFunction Description

1. Copy Copy data from source HDD to targets. (There are four copy modes for selection at function 6.2)

2. Compare Comparison between the source and targets to make sure copy accuracy

3. Copy + Compare Execute compare function automatically after copy

4. EraseIt is able to enable/disable erase of source HDD at function 6.7.2

4.1 Quick EraseErase the INDEX of HDD, and take very short time

4.2 Full EraseErase the whole HDD

4.3 DoD EraseErase HDDs 3 times complying with USA Department of Defense (DoD) standard

4.4 DoD EraseComp Erase HDDs 3 times complying with DoD standard and compare once bit-by-bit to check if data is completely erased.

4.5 Secure EraseThe international authorized high standard Secure Erase function. It is able to erase the area which is not loadable.

5. Utility

5.1 Show Disk InfoShows HDD’s basic information such as HDD model name and capacity.

5.2 Update System

5.2.1 Update BIOSTo update the system firmware via the HDD.

5.2.2 Create Update HDDTo format the HDD with a 2GB FAT partition in order to quickly save firmware in the HDD.

5.3 System Info.This function will show information of the duplicator system, including controller model number and software version.

6. Setup

6.1 Start-up MenuSelect which function is shown first when the system is turned on.

6.2 Copy AreaSetup copy mode.

6.1.1 System and FilesSet to copy source HDD's data area only.

6.1.2 All PartitionsSet to copy source HDD's.

6.1.3 Whole HDDSet to copy the whole source HDD.

6.1.4 Percentage(%)Set up percentage range of HDD for copy.

6.3 Skip ErrorSet to ignore error of source HDD while copying. (0-65535 or unlilmited)

6.4 Minimum SpeedSet to check HDDs’ minimum speed as 10, 20, 30~300MB/Sec or don’tcheck.

11

Function Table 2

6. Setup

6.5 Check Source Minimum SpeedSet to check minimum speed including source HDDs or not.

6.6 LanguageSelect preferred language.

6.7 Advanced Setup

6.7.1 Unknown Format

6.7.1.1 Copy UnknownCopy unknown area when the device can not identify the format.

6.7.1.2 Skip UnknownSkip to copy unknown area when the device can not identify the format.

6.7.2 Erase MasterSetup to erase source HDD or not.

6.7.2.1 DisableDisable erase source HDD.

6.7.2.2 EnableEnable erase source HDD.

6.7.3 Erase Pattern

6.7.3.1 ONE ByteA random character to be written into every byte.

6.7.3.2 Big Random DataA set of random character to be written into a set of area.

6.7.4 Wait HDD TimeAuto start time after plugging in HDD. Able to set from 0 to 30 seconds.

6.7.5 Lock KeyAfter keys locked, only OK and ESC key are working.

6.7.5.1 Do Not Lock Key

6.7.5.2 Do Lock Key

6.7.6 Copy HPA AreaSetup to copy HPA hidden area or not.

6.7.6.1 No

6.7.6.2 Setting HPA

6.7.6.3 Copy and Setting

6.7.7 Transfer RateSelect the proper transfer rate UDMA2-7. 7 is the fastest.

6.7.8 Stop Motor TimeSet the time waited for the motor to stop from 1-~20 seconds after executing funciotn.

6.7.9 Adjust Clock Adjust system time clock on LCD screen.

6.8 Restore DefaultBack to original manufacturer setting.

7. Log Manager(For advanced series only)

7.1 Advanced Function

7.1.1 Clear ALL LogClean out the log records after entering password.

7.1.2 Setup PasswordSet up the password for cleaning log records.

12

3 ReminderReminder⌘ Before You Start

☉ Make sure to use stable power supply. ☉ Please use at clean & dry environment. ☉ Make sure to use stable power supply. ☉ Please keep the environment well ventilated.

☉ When the duplicator operates, it is normal for the machine to heat up.

☉ Please do not move the duplicator during operation to ensure better operation.

☉ Please do not remove HDDs during operation to avoid damage.

☉ Please use power supply of its original manufacturer to ensure working normal. ☉ Eliminate Static electricity:Static electricity may cause duplication error. Please pay attention to the duplicator environment and operators’ equipment. It is recommended to purchase static electricity elimination equipments to avoid static electricity shock when stay in high static electricity.

13

How to Copy HDDs 4How to Copy HDDs⌘ Start to CopyStep 1Prepare a source HDD and target HDD (*it's strongly recommended to the size of source and target are the same)

Source HDD Target HDD

Note ☉ SATA interface applies on the duplicator, no matter SATA 1.0/2.0/3.0 are all supported. ☉ Assemble adaptors if user needs to copy device with other interface, e.g., eSATA and iVDR.

Step 2Place source HDD at source port, targets HDD to other ports.

14

4 How to Copy HDDsStep 3Use ▲▼ to select "1. Copy" then press "OK". Duplication will proceed.

Note When all the target HDD ports are plugged, duplicator would start copying automatically. If not all are plugged, the number of targets shows on LCD. Press "OK" to start.

The information below shows on LCD during duplication.

Note ☉ The number shows in the ( ) is the port # of the slowest HDD. ☉ Press ▲▼ together for 5 seconds to stop operation on the slowest HDD. ☉ It is able to use "On-Time Monitor" feature to check operation speed of every port.

Step 4Quantity of copy OK/Fail and duplication time would show on LCD after duplication completes.

⌘ Setup before Copy/ComparePlease pay attention to the following settings before copy.

❶Set Copy Area of Source HDDChoose appropriate copy area can greatly reduce operation time and have better efficiency. There are four copy modes with different copy area : ① System and Files, ② All available partition area, ③ Whole HDD, ④ User set the percentage range of HDD.

15

How to Copy HDDs 4System and Files (Quick Copy, Quick Compare)It will copy source HDD's System and Files instead of the whole HDD. The system will analyze the source HDD and identify the data area to copy. As long as the source HDD's data within the target HDD's space, the copy will be processed. FAT16/32/64, NTFS, ext2/3/4, HFS+, HFS, HFX are supported for this copy mode.

Only 120G data area will be copied, it takes 12mintues.

Source

Partition 1(150G)Data 30G

Partition 1(200G)Data 90G

500GB

Duplication Target

500GB

All PartitionThis mode will bit by bit copy all of the partitions no matter there is data exist or not. The capacity of target HDD has to be bigger than the partition required capacity

500GB 500GB

Source

Partition 1(150G)Data 30G

Partition 1(200G)Data 90G

Duplication Target

Only 350G partition area will be copied, it takes 48mintues.

16

4 How to Copy HDDsWhole HDDIt is to copy the whole source HDD, no matter of the content, format, partition or empty space. This mode will take much more time to duplicate the source HDD completely.

500GB 500GB

Source

Partition 1(150G)Data 30G

Partition 1(200G)Data 90G

Duplication Target

Entire 500GB HDD will be copied.

Percentage(%)Copy the percentage selected of source HDD.

25％

32％

500GB

25％

32％

500GB

Source Duplication Target

Only copy the selected area, other area or data will not be copied.

Note Duplication time is affected by "transfer speed of HDD".

17

How to Copy HDDs 4Copy area selection:e.g. There are two partitions in one 500GB HDD. Data and OS(120GB) are saved in the partition.

System and files

500GB

All partition

500GB

Whole HDD

500GB

Copy/Compare area 30G+90G= 120G

Copy/Compare area 150G+200G= 350G

Copy/Compare area500G

Note ☉ It is recommended to execute "Compare" after "Copy" to confirm the accuracy. ☉ It is recommended to copy data by function "3.Copy+Compare".

❷ Set Tolerance of Bad TrackSelect function "6.3 Skip Error" to set the number of error you accept to skip during copy process. Set tolerance volume from 0/2/5....65535 or unlimited.If the HDD is very critical for content correctness, please set the Skip Error to be "0".It is strongly recommended to keep the Skip Error to be "0" to run tasks. When you set Skip Error not to "0", for some HDDs it might cause tasks passed on the duplicator but fail to use HDDs on your device.

➌ Auto Skip Lower-Speed HDDsEnter function "6.4 Minimum Speed" to setup tolerance speed of target HDDs. Set to check HDDs’ lowest tolerance speed. Users can choose “Don’t care” or set the speed value among 10/20/30~300MB/second. The system will skip any HDD which cannot reach the minimum speed. This setting enables to speed up copying and select HDD speed higher than the setting speed.

18

4 How to Copy HDDs

➍ Auto Skip Lower-Speed SourceThis setting enables to setup whither to check minimum speed including source HDDs. Select “Yes” to include source HDDs or select “No” to skip source HDDs checking. This function enables to speed up copying speed and setup minimum speed for source HDD.

⌘ Troubleshooting When Duplication FailsCheck if too many bad tracks on HDDs cause duplication failures.

☉ Check the setting of "6.3 Skip Error". Reset the number to 0 and copy error disks again.

☉ Make sure all data cables are properly and firmly connected.

☉ Make sure the capacity of source HDD is smaller than target. Check HDDs capacity by selecting "5.1 Show Disk Info".

19

How To Confirm Copy Accuracy 5How to Confirm Copy Accuracy⌘ Compare Duplication ResultsStep1Prepare source HDD and target HDD.

Source HDD Target HDD

Step 2Place source HDD at source port, targets HDD to other ports.

Step 3Use ▲▼ to select "2.Compare" then press "OK". Data compare will proceed.

Note When all the target HDD ports are plugged, duplicator would start copying automatically. If not all are plugged, the number of targets shows on LCD. Press "OK" to start.

⌘ Setting of Compare FunctionIt is able to set compare area of HDD at function "6.1 Copy Area"There are four different compare area for selection : ① System and Files, ② All available partition area, ③Whole HDD, ④ Percentage Compare.

20

6 How to Erase HDDsHow to Erase HDDsNote Please notice the data within the HDD will be erased after executing the function.

⌘ How to Erase DataStep 1Prepare the HDD for erasure.

Erase HDD

Step 2Insert the HDD into target port.

Note Function 6.7.2 Erase Master is to determine erase source HDD or not. The default setting is "Disable erase source HDD".

Step 3Use "UP"/"DOWN" to select the desired erase method, then press "OK". Data Erase will proceed.

21

How to Erase HDDs 6⌘ Setting of Erase FunctionThere are five erase methods: ➀ Quick Erase, ➁ Full Erase, ➂ DoD Erase, ➃ DoD Erase Comp, ➄ Secure Erase

➀ Quick EraseThe function will ONLY erase the index of the HDD. It is the quickest way to erase HDD. It will damage the data in HDD, please make sure you have backup all important data before using this function

➁ Full EraseThe function will erase the whole sectors on the target HDD. It will take longer time than quick erase. It will damage the data in HDD, please make sure you have backup all important data before using this function.

➂ DoD Erase This is to comply with the U.S.A. Department of Defense (DoD 5220) standard to fully erase the HDD three times bit by bit to rewrite HDD to guarantee the data was deleted. It will damage the data in HDD, please make sure you have backup all important data before using this function.

22

6 How to Erase HDDs➃ DoD Erase CompBesides DoD erase, this function will also execute compare function to make sure the random bit was correctly written. This way of erase is to erase HDD over each sector three times: the first time with zeros (0x00), second time with 0xFF and the third time with random characters. There is one final pass to compare random characters by reading. It will damage the data in HDD, please make sure you have backup all important data before using this function.

Select random pattern

❶ Overwrite by fixed method

37373737373737373737373737373737373737373737373737373737373737373737373737373737

23

How to Erase HDDs 6❷ Overwrite by random method

26AE891DF74519D55CE6621457E48AAB6890DD51473DAA9A82BBE55713C4859CBFFA147

➄ Secure EraseThe international authorized high standard Secure Erase function. It overwrites every single track on the hard drive with "00". Even HPA/DCO or other data area which are not able to load, can be erased all together

Note Please do not disrupt during Secure Erase, otherwise it would cause irretrievable error on HDD, which turns the HDD unusable.

24

7 How to Update BIOSHow to Update BIOS⌘ Update by BIOS HDDStep 1 Prepare one HDD and connect it to source port, then select function 5.2.2 Format HDD.

Step 2 Format the HDD

Note ☉ Before updating firmware, one FAT, 2GB partition will be formatted in HDD. That would reduce searching time, and speed up firmware update. ☉ The data saved in this HDD will be erased.

Step 3Download the latest firmware from PC and save it in HDD.

Step 4Insert HDD into source port (first port), select function 5.2.1 Update BIOS. Update would complete in one minute.

25

How to Use PC-Monitoring 8How to Use PC-Monitoring1 Real-time PC MonitoringReal-time PC-Monitoring is a convenient tool to monitor real-time status for advanced series, that real-time tasks skip lower speed HDDs in writing process to keep its best performance. By connecting to PC, all status can be viewed clearly, including copy process.

⌘ Preparation before Start§ Installation The related drivers and software ithe series are descripted as followings:• LV07H: PC-Monitoring driver for HDD duplicators.• PL-2303: USB-to-Serial program connects USB-port of your computer to the

duplicator.• PC-Link: Software package for PC monitoring interface.

Step 1Open the directory. Click on the icon "PC Link.exe" to start installation. In the next window, continue to click <Install> to start and follow the instruction. Or, open icon directly, LV07H.exe, to launch software.

26

8 How to Use PC-MonitoringStep 2After launching PC-Link software, the install device driver of PL-2303 USB-to-Serial is initiated. Choose tab <PC Driver> and press <Install Driver> to continue. When the Wizard screen pop up, click <Next> to start installation.

Step 3Please wait during installation processing.

Step 4Click <Finish> to complete installation.

27

How to Use PC-Monitoring 8§ Launch PC-MonitoringStep 1Install Synchronous Monitor Software LV07H , and its driver PL-2303 .

Step 2Prepare USB cable to connect between computer and the duplicator.

Step 3Launch LV07H by double clicking on software icon "LV07H.exe".

Step 4Turn on the power of the duplicator, LV07H starts to link with the duplicator.

Step 5When the following screen shown, the duplicator is linked to the computer successfully, ready to use real-time monitoring function.

Step 6If the status is not shown normal online status, please check step 1~3 again.

28

8 How to Use PC-Monitoring⌘ Operation of PC-MonitoringNote Please use specific computer to do PC-Monitoring, and prevent PC operating other

tasks. The information of PC-Monitoring can be instant synchronized.

Step 1The status of duplicator shows on-line, and then open monitoring screen. The program is ready to work when the status show STANDBY.

Step 2After placing source & target HDDs into duplicator, execute jobs for duplicator.The program shows all related information of HDDs. It is able to monitor detail information of every HDD through PC-Monitoring, e.g. HDD model, S/N, copy speed, and etc. It is able to record and monitor all the function and work progress during operation.

Note Copy speed varies during operation.

Step 3After duplication, the program will show average speed of each HDD.

29

How to Use PC-Monitoring 82 Log ReportPC-Monitoring program LV07H not only browses log report through PC, but also export log report into .txt file through PC. The file can be saved at specified location and file name. Anyone has the need of management and archive log report can analyses the file on computer. Because log report save every S/N and operation time of every single HDD, it is good for production analyses in the future.

⌘ Browse Log Report through PCBesides PC-Monitoring, LV07H can browse Log Report of duplicator through PC

Step 1After finishing all the task of duplicator, press "ESC" key on duplicator. The status shown on LV07H is "STANDBY". Scroll down to the section, Log Data, on the middle of window, and then select "Generate Log Report".

Step 2After entering "Open Log Window", select the date or period of time for log report generation.

30

8 How to Use PC-Monitoring

After selecting the date or period of time for log report generation, log report would shows.

Note If there is no record saved at the selected period of time, or record had been wiped out, the program would show No match records!

Step 3Specify save location and file name

Step 4Click Save, log report is saved to the specified location

31

How to Use PC-Monitoring 8§ Log Records & ScreenThe system can only keep log totally up to 30,000 records of operation information of HDD. One operation on a single HDD is saved as one record. For example, there are 21 records saved when duplicate from one HDD to 20 targets.The log manager can only keep 30000 records. One instruction onto one HDD is recorded as one piece of log record. (e.g. duplication from 1 HDD to 5 targets will be recorded to 5 piece of log.)If the amount of the records reaches up to the limit, the new record will replace and cover the existing record from the beginning and the previous record will be covered one by one. The existing log will keep enternity until all records space full to be covered by newer ones.

Background information of this log report

Original Source Record: Manage and control the source , confirm the size of the data are consistent.Detailed task records: best reference for production and HR management.

Time of execution

Content was protected by Invisible-Ink Technology ! Please check it by LV07Z.exe

iSecuLog protection: guarantee the original data without any changes

HDD S/N

Yield analysis: the pass and failure rate for yield records.

32

8 How to Use PC-Monitoring⌘ Advanced Function (For advanced series only)➊ Function 7.1.1 Clear ALL LogsAfter user entering password, the log report saved in duplicator can be wiped out.

Note Please close PC-Monitoring program LV07H or disconnect PC from duplicator while clearing log report.

➋ Function 7.1.2 Setup PasswordUsers can reset password to protect log records. To execute function "7.1.1", "7.1.2", you must use "UP"/"DOWN" keys to input password. The default password is "123456".

33

FAQPC-Monitoring

Questions of PC-Monitoring Answer

Why duplicator can not execute PC-Monitoring?

Make sure USB cable is connected betwenn PC and dupl icator. I t is recommended to attach USB cable and then open LV07H program.

Why the monitoring information of LV07H lags, and cannot catch up duplicator?

PC-Monitoring consumes most of process resource of PC. If PC process ability is low; runs other tasks at the same time, LV07H might lags. It is highly recommended to run with PC with better process ability, instead of operating other program on PC.

34

FAQThe Duplicator

Questions of duplicators Solution

LCD shows "HDD Too Small"

1. The capacity of source HDD is bigger than target HDD. E.g., copy 500GB HDD to 250GB HDD.

2. The capacity of source and target are the same, but internal capacity might be slightly different.

What OS does duplicator support? Duplicator copies any kinds of OS

Can duplicator copy IDE HDD, SSD, mSATA, etc?

Yes, it can. As long as adaptor can adopt to SATA interface.

How long does it take to duplicate?For example, if the duplicator supports 8.1GB/min copy speed. It's around 2 min to copy Win8 OS(approx 12GB)

How big the capacity of HDD does duplicator support?

Duplicator supports up to 6TB HDD, and MBR/GBT format HDD

Can I interupt the copy task while it is not finished?

Yes, the program (copy, compare and erase) can be stopped while it is in processing by pressing ESC for aobut 3~4 seconds

Will it be safe if I remove the HDD right after copy process?

Yes, the device will automatically cut off power of each port to protect HDD during removal from the duplicator. The power of each port will be only be output when the operation is started.

What kind of format does duplicator support?

FAT16/32/64, ext2/3, NTFS, HFS, HFX, HFS+ are supported for Systems and Files Copy. If copy the format other than those above, it transfer to All Partition Copy.

35

SpecificationSpecificationProduct Name Rack Mount HDD/SSD Duplicator

Model KV500 KV600

Target4 6

Expandable up to 254 targets

Buffer 128MB per port

Display 2x16 backlight Monochrome LCD

Control Button 4 Keys ( ▲ /Up, ▼ /Down, OK/Confirm, ESC/Exit)

Compatible HDDWithout adapter: 2.5"/3.5" SATA HDD/SSDWith adapter: CRU

Comapre Mode Bit-for-bit data comparison

Erase Mode Quick Erase, Full Erase, DoD Erase, Secure Erase

Copy Format

Quick Copy: FAT16/32/64, NTFS, Linux (Ext2/3/4), HFS/HFS+/HFX

All Partitions/Whole HDD Copy/Percentage copy : All Formats

Advanced Format

PC Monitoring

OS Supported

Skip Bad sector copy by self-setting toleranceSupport MBR, GPT, advanced format HDD (18TB above)

PC monitoring for real-time status

All (Windows, Linux, RAID, Other stand-alone systems)

Power SupplyAutomatic power controlAdjustable voltage 115V~240V, 50/60Hz.

Temperature Storage temperature: -20ºC ~85ºC

Working temperature: 5ºC ~45ºC

Humidity Storage humidity: 5%~95%

Working humidity: 20%~80%

Certifications FCC, CE, RoHS

Specifications are subject to change without notice.