e-Novice JANUAR 2013

Orodja za prebijalne stroje TRUMPF®

MATE PRECISION TOOLING ima v svoji ponudbi celovito paleto orodij in orodnih sistemov zasno-vanih za izdelavo kakršnih koli oblik in deformacij na vašem TRUMPF prebijalnem stroju. V nadalje-vanju smo nekaj besed namenili predstavitvi podjetja in novostim pri orodnemu jeklu, ki ga MATE uporablja za izdelavo orodja. Sledijo kratek opis ponudbe standardnih sistemov orodij ter “slitting“ orodij. Na koncu na kratko predstavljamo še ponudbo specialnih orodij MATE, ki so na voljo za pre-bijalne stroje TRUMPF.

SOLUTION BULLETIN

1295 Lund Boulevard Anoka MN 55303 Phone 763.421.0230 800.328.4492 Fax 763.421.0285 800.541.0285

mate.com

USING EASYSNAP™ FOR QUICK, CLEAN PARTS SEPARATION

THE PROBLEM: Fabricators use a variety of methods to separate multiple parts from a sheet of material. A frequently used method places small tabs between parts by programming the spacing of a slitting punch. While the tabs keep the parts intact during punching, they can be difficult to remove and often leave rough or sharp edges that usually require a secondary operation to remove.

THE MATE SOLUTION: Using a Mate EasySnap™ tool (below) solves these issues because it allows you to build in a way to snap parts out of sheet metal without using a slitting or punching tool. EasySnap allows fabricators to simply snap punched components out of sheet metal by hand, making life much easier. Since EasySnap leaves a clean, smooth edge, there is no need for secondary operations. EasySnap uses a V-line stencil machined onto the face of the upper and lower tools. As the tools penetrate the sheet, they create a line of weakness (snap-line) in both surfaces of the sheet metal. The sheet metal can then be snapped apart by bending the material along the snap-line. The actual depth of penetration and force required to snap the part is dependent on the ductility and thickness of the material being punched. It also keeps parts removal easy since the parts simply snap off the sheet.

EasySnap™ lines

EasyBend™ lines

Illustrations of a part made using EasySnap™ (and EasyBend™). (Left) Flat part after EasySnap and EasyBend lines created. (Center) Same part after EasySnap portions removed with burr-free edges. (Right) Samepart,aftersidesarebentupwithEasyBend.Thesideswillseparateeasilywithburr-freeedges.

SOLUTION BULLETIN

1295 Lund Boulevard Anoka MN 55303 Phone 763.421.0230 800.328.4492 Fax 763.421.0285 800.541.0285

mate.com

USING EASYSNAP™ FOR QUICK, CLEAN PARTS SEPARATION

THE PROBLEM: Fabricators use a variety of methods to separate multiple parts from a sheet of material. A frequently used method places small tabs between parts by programming the spacing of a slitting punch. While the tabs keep the parts intact during punching, they can be difficult to remove and often leave rough or sharp edges that usually require a secondary operation to remove.

THE MATE SOLUTION: Using a Mate EasySnap™ tool (below) solves these issues because it allows you to build in a way to snap parts out of sheet metal without using a slitting or punching tool. EasySnap allows fabricators to simply snap punched components out of sheet metal by hand, making life much easier. Since EasySnap leaves a clean, smooth edge, there is no need for secondary operations. EasySnap uses a V-line stencil machined onto the face of the upper and lower tools. As the tools penetrate the sheet, they create a line of weakness (snap-line) in both surfaces of the sheet metal. The sheet metal can then be snapped apart by bending the material along the snap-line. The actual depth of penetration and force required to snap the part is dependent on the ductility and thickness of the material being punched. It also keeps parts removal easy since the parts simply snap off the sheet.

`

EasySnap™ lines

EasyBend™ lines

Illustrations of a part made using EasySnap™ (and EasyBend™). (Left) Flat part after EasySnap and EasyBend lines created. (Center) Same part after EasySnap portions removed with burr-free edges. (Right) Same part, after sides are bent up with EasyBend. The sides will separate easily with burr-free edges.

SOLUTION BULLETIN

1295 Lund Boulevard Anoka MN 55303 Phone 763.421.0230 800.328.4492 Fax 763.421.0285 800.541.0285

mate.com

USING EASYSNAP™ FOR QUICK, CLEAN PARTS SEPARATION

THE PROBLEM: Fabricators use a variety of methods to separate multiple parts from a sheet of material. A frequently used method places small tabs between parts by programming the spacing of a slitting punch. While the tabs keep the parts intact during punching, they can be difficult to remove and often leave rough or sharp edges that usually require a secondary operation to remove.

THE MATE SOLUTION: Using a Mate EasySnap™ tool (below) solves these issues because it allows you to build in a way to snap parts out of sheet metal without using a slitting or punching tool. EasySnap allows fabricators to simply snap punched components out of sheet metal by hand, making life much easier. Since EasySnap leaves a clean, smooth edge, there is no need for secondary operations. EasySnap uses a V-line stencil machined onto the face of the upper and lower tools. As the tools penetrate the sheet, they create a line of weakness (snap-line) in both surfaces of the sheet metal. The sheet metal can then be snapped apart by bending the material along the snap-line. The actual depth of penetration and force required to snap the part is dependent on the ductility and thickness of the material being punched. It also keeps parts removal easy since the parts simply snap off the sheet.

`

EasySnap™ lines

EasyBend™ lines

Illustrations of a part made using EasySnap™ (and EasyBend™). (Left) Flat part after EasySnap and EasyBend lines created. (Center) Same part after EasySnap portions removed with burr-free edges. (Right) Same part, after sides are bent up with EasyBend. The sides will separate easily with burr-free edges.

SOLUTION BULLETIN

1295 Lund Boulevard Anoka MN 55303 Phone 763.421.0230 800.328.4492 Fax 763.421.0285 800.541.0285

mate.com

USING EASYSNAP™ FOR QUICK, CLEAN PARTS SEPARATION

THE PROBLEM: Fabricators use a variety of methods to separate multiple parts from a sheet of material. A frequently used method places small tabs between parts by programming the spacing of a slitting punch. While the tabs keep the parts intact during punching, they can be difficult to remove and often leave rough or sharp edges that usually require a secondary operation to remove.

THE MATE SOLUTION: Using a Mate EasySnap™ tool (below) solves these issues because it allows you to build in a way to snap parts out of sheet metal without using a slitting or punching tool. EasySnap allows fabricators to simply snap punched components out of sheet metal by hand, making life much easier. Since EasySnap leaves a clean, smooth edge, there is no need for secondary operations. EasySnap uses a V-line stencil machined onto the face of the upper and lower tools. As the tools penetrate the sheet, they create a line of weakness (snap-line) in both surfaces of the sheet metal. The sheet metal can then be snapped apart by bending the material along the snap-line. The actual depth of penetration and force required to snap the part is dependent on the ductility and thickness of the material being punched. It also keeps parts removal easy since the parts simply snap off the sheet.

`

EasySnap™ lines

EasyBend™ lines

Illustrations of a part made using EasySnap™ (and EasyBend™). (Left) Flat part after EasySnap and EasyBend lines created. (Center) Same part after EasySnap portions removed with burr-free edges. (Right) Same part, after sides are bent up with EasyBend. The sides will separate easily with burr-free edges.

PRIPOROČILA IN REŠITVEZA PREBIJANJE

MATE PRECISION TOOLINGŽe od leta 1962 proizvaja prebijalno orodje za vse večje proizvajalce CNC prebijalnih strojev.

MATE PRECISION TOOLING je vodilni svetovni proizvajalec visoko kakovostnega orodja za prebi-jalne stroje. Proizvajajo originalno in nadomestno orodje za prebijalne stroje Amada, Euromac, Finn-Power, LVD, Murata Wiedemann, Salvagnini, Strip-pit, Nisshinbo, Trumpf ter vse druge, ki uporabljajo Thick Turret sistem.

Sedež podjetja in glavnina proizvodnje je ZDA, kar pa ni ovira za hitre odzivne čase in kratke dobavne roke! Poleg tega imajo od leta 2009 proizvodnjo tudi v Nemčiji.

Visoka kvaliteta, kratek čas od naročila do do-bave in cena so kvalitete, ki so prepričale mnoge.

MATE PRECISION TOOLING solutions center

Center s nahaja v tovarni v ZDA. Center se med drugim uporablja tudi za testiranje in razvoj orodij, saj imajo v njem na voljo najnovejše prebijalne stroje Prima-Power, Trumpf, Muratec in Euromac.

Amada EUROMAC Prima-Power Murata Wiedermann NISSHINBO StrippitLVD TRUMPF

SOLUTION BULLETIN

1295 Lund Boulevard Anoka MN 55303 Phone 763.421.0230 800.328.4492 Fax 763.421.0285 800.541.0285

mate.com

USING EASYSNAP™ FOR QUICK, CLEAN PARTS SEPARATION

THE PROBLEM: Fabricators use a variety of methods to separate multiple parts from a sheet of material. A frequently used method places small tabs between parts by programming the spacing of a slitting punch. While the tabs keep the parts intact during punching, they can be difficult to remove and often leave rough or sharp edges that usually require a secondary operation to remove.

THE MATE SOLUTION: Using a Mate EasySnap™ tool (below) solves these issues because it allows you to build in a way to snap parts out of sheet metal without using a slitting or punching tool. EasySnap allows fabricators to simply snap punched components out of sheet metal by hand, making life much easier. Since EasySnap leaves a clean, smooth edge, there is no need for secondary operations. EasySnap uses a V-line stencil machined onto the face of the upper and lower tools. As the tools penetrate the sheet, they create a line of weakness (snap-line) in both surfaces of the sheet metal. The sheet metal can then be snapped apart by bending the material along the snap-line. The actual depth of penetration and force required to snap the part is dependent on the ductility and thickness of the material being punched. It also keeps parts removal easy since the parts simply snap off the sheet.

EasySnap™ lines

EasyBend™ lines

Illustrations of a part made using EasySnap™ (and EasyBend™). (Left) Flat part after EasySnap and EasyBend lines created. (Center) Same part after EasySnap portions removed with burr-free edges. (Right) Samepart,aftersidesarebentupwithEasyBend.Thesideswillseparateeasilywithburr-freeedges.

SOLUTION BULLETIN

1295 Lund Boulevard Anoka MN 55303 Phone 763.421.0230 800.328.4492 Fax 763.421.0285 800.541.0285

mate.com

USING EASYSNAP™ FOR QUICK, CLEAN PARTS SEPARATION

THE PROBLEM: Fabricators use a variety of methods to separate multiple parts from a sheet of material. A frequently used method places small tabs between parts by programming the spacing of a slitting punch. While the tabs keep the parts intact during punching, they can be difficult to remove and often leave rough or sharp edges that usually require a secondary operation to remove.

THE MATE SOLUTION: Using a Mate EasySnap™ tool (below) solves these issues because it allows you to build in a way to snap parts out of sheet metal without using a slitting or punching tool. EasySnap allows fabricators to simply snap punched components out of sheet metal by hand, making life much easier. Since EasySnap leaves a clean, smooth edge, there is no need for secondary operations. EasySnap uses a V-line stencil machined onto the face of the upper and lower tools. As the tools penetrate the sheet, they create a line of weakness (snap-line) in both surfaces of the sheet metal. The sheet metal can then be snapped apart by bending the material along the snap-line. The actual depth of penetration and force required to snap the part is dependent on the ductility and thickness of the material being punched. It also keeps parts removal easy since the parts simply snap off the sheet.

`

EasySnap™ lines

EasyBend™ lines

Illustrations of a part made using EasySnap™ (and EasyBend™). (Left) Flat part after EasySnap and EasyBend lines created. (Center) Same part after EasySnap portions removed with burr-free edges. (Right) Same part, after sides are bent up with EasyBend. The sides will separate easily with burr-free edges.

SOLUTION BULLETIN

1295 Lund Boulevard Anoka MN 55303 Phone 763.421.0230 800.328.4492 Fax 763.421.0285 800.541.0285

mate.com

USING EASYSNAP™ FOR QUICK, CLEAN PARTS SEPARATION

THE PROBLEM: Fabricators use a variety of methods to separate multiple parts from a sheet of material. A frequently used method places small tabs between parts by programming the spacing of a slitting punch. While the tabs keep the parts intact during punching, they can be difficult to remove and often leave rough or sharp edges that usually require a secondary operation to remove.

THE MATE SOLUTION: Using a Mate EasySnap™ tool (below) solves these issues because it allows you to build in a way to snap parts out of sheet metal without using a slitting or punching tool. EasySnap allows fabricators to simply snap punched components out of sheet metal by hand, making life much easier. Since EasySnap leaves a clean, smooth edge, there is no need for secondary operations. EasySnap uses a V-line stencil machined onto the face of the upper and lower tools. As the tools penetrate the sheet, they create a line of weakness (snap-line) in both surfaces of the sheet metal. The sheet metal can then be snapped apart by bending the material along the snap-line. The actual depth of penetration and force required to snap the part is dependent on the ductility and thickness of the material being punched. It also keeps parts removal easy since the parts simply snap off the sheet.

`

EasySnap™ lines

EasyBend™ lines

Illustrations of a part made using EasySnap™ (and EasyBend™). (Left) Flat part after EasySnap and EasyBend lines created. (Center) Same part after EasySnap portions removed with burr-free edges. (Right) Same part, after sides are bent up with EasyBend. The sides will separate easily with burr-free edges.

SOLUTION BULLETIN

1295 Lund Boulevard Anoka MN 55303 Phone 763.421.0230 800.328.4492 Fax 763.421.0285 800.541.0285

mate.com

USING EASYSNAP™ FOR QUICK, CLEAN PARTS SEPARATION

THE PROBLEM: Fabricators use a variety of methods to separate multiple parts from a sheet of material. A frequently used method places small tabs between parts by programming the spacing of a slitting punch. While the tabs keep the parts intact during punching, they can be difficult to remove and often leave rough or sharp edges that usually require a secondary operation to remove.

THE MATE SOLUTION: Using a Mate EasySnap™ tool (below) solves these issues because it allows you to build in a way to snap parts out of sheet metal without using a slitting or punching tool. EasySnap allows fabricators to simply snap punched components out of sheet metal by hand, making life much easier. Since EasySnap leaves a clean, smooth edge, there is no need for secondary operations. EasySnap uses a V-line stencil machined onto the face of the upper and lower tools. As the tools penetrate the sheet, they create a line of weakness (snap-line) in both surfaces of the sheet metal. The sheet metal can then be snapped apart by bending the material along the snap-line. The actual depth of penetration and force required to snap the part is dependent on the ductility and thickness of the material being punched. It also keeps parts removal easy since the parts simply snap off the sheet.

`

EasySnap™ lines

EasyBend™ lines

Illustrations of a part made using EasySnap™ (and EasyBend™). (Left) Flat part after EasySnap and EasyBend lines created. (Center) Same part after EasySnap portions removed with burr-free edges. (Right) Same part, after sides are bent up with EasyBend. The sides will separate easily with burr-free edges.

PRIPOROČILA IN REŠITVEZA PREBIJANJE

M4PM™ orodno jeklo za najboljše rezultate s Trumpf Style orodji MATE

Pri Mate-u so se proti koncu lanskega leta odločili, da kupcem Trumpf orodij ponudijo samo najboljše. Zato večino orodij, ki so bila v preteklosti iz materiala HSS M2 sedaj izdelujejo iz materiala M4PM™. To vključuje:

Vse običajne • Trumpf Style prebijače velikosti SIZE 0 in SIZE 1

Vse • QuickLock™ prebijače velikosti SIZE 1

Vse • Minimatic prebijače velikosti SIZE 0 in SIZE 1 (razen SIZE-X)

Vse • NEXT™ prebijače velikosti SIZE 40 in SIZE 76

Vse Trumpf-Style SIZE 5 in SIZE 10 • Multitool prebijače in ma-trice

Vse • LongLife™ prebijače in matrice orodij za razrez

Cene orodij so kljub izdelavi iz boljšega orodnega jekla enake!

Vse ostale standardne prebijače v Mate-u še naprej izdelujejo iz materiala HSS M2. Material HSS M2 je zelo dobro odporen proti obrabi. Glavne prednosti orodnega jekla M4PM™ pa so še boljša odpornost proti obrabi in večja trdnost. Vse to se odraža na tem da orodja iz materiala M4PM™ zdržijo 2-4x več prebijanj, kot orodja iz običajnih orodnih jekl HSS. Standardne matrice v MATE-u izdelu-jejo iz materiala A2.

V grafih na desni je prikazana primerjava obstojnosti orodja med prebijači iz materiala M4PM™, HSS in ostalimi materiali. Iz grafov izhaja da so Trumpf orodja iz materiala M4PM™ za 50% in več bolj odporna proti obrabi kot orodja iz običajnih orodnimi jekli, ki jih uporabljajo drugi proizvajalci.

MATE M4PM™ Običajna orodna jekla

PONUDBA PREBIJALNEGA ORODJAZA PREBIJALNE STROJE TRUMPF

Mate ima v svoji ponudbi celovito paleto orodij in orodnih sistemov zasnovanih za izdelavo kakršnih koli oblik in deformacij na vašem Trumpf prebijalnem stroju.

Glede na vaše zahteve in potrebe so na voljo trije standardni sistemi orodij: (1) MATE Trumpf Stlye orodja, (2) MATE QuickLock™ orodja, ter (3) MATE Next™ orodja.

MATE Trumpf Stlye1. orodja so standardno na-domestno orodje za prebijalne stroje Trumpf.

Orodje vključuje celoten razpon Trumpf prebijačev, matric, snemalcev, smirnih obročev in dodat-kov; vse odlikujejo visoke tolerance, izdelani pa so iz vrhunskega orodnega jekla, ki je garant za zmogljivost in vzdržljivost orodja.

Na voljo so tudi Minimatic ter HavyDuty orodja, orodja in Multitool-i 5 in 10, ter orodja za Multi-tool-e 4 in 6.

MATE QuickLock™2. orodja so oblikovana tako, da omogočajo hitrejšo namestitev orodja.

Mate QuickLock™ prebijači so opremljeni z po-ravnalnim pinom. Univerzalni smirni obroč pa ima utor za pin prebijača, ki omogoča poravnavo prebijačev brez uporabe zato namenjenega po-ravnalnega držala. Uporablja pa se lahko tako za SIZE 1 in SIZE 2 velikosti Trumpf prebijalnega orodja.

MATE Next™3. orodje je insertno orodje, ki omogoča daljšo življenjsko dobo ter posledično nižje stroške prebijanja.

Insertni sistem Next™ sestavljajo držalo za insert-ne prebijače, izmenljiv insertni prebijač in pre-cizna podložka.

Next™ držalo za insertne prebijače združuje funkcijo običajnega vpetja prebijača in smernega obroča v en sestav. Omogoča natančno porav-navo orodja in enostavno in hitro nameščanje in-sertnih prebijačev.

Z uporabo Next™ preciznih podložk, ki jih names-timo med prebijač in držalo po tem ko odbrusi-mo 3 mm materiala, izmenljivi insertni prebijači omogočajo povečanje življenjske dobe med brušenji. Ker precizna podložka vrne prebijač na prvotno pozicijo, zamenjava z novim še ni potreb-na.

MATEQuickLock™

Trumpf Style

MATENext™

Poleg standardnih orodij so v ponudbi tudi slitting orodja, in sicer; (4) Mate Eurostyle™ orodja in (5) Mate Longlife™ orodja.

MATE Eurostyle™ 4. orodja za razrez so zasno-vana za natančen in hiter razrez oziroma odrez pločevine s Trumpf prebijalnimi stroji. Zaradi posebnih značilnosti orodja ni stranskih obre-menitev in deformacij, ki se sicer lahko pojavijo pri odrezu s standardnim orodjem na prebijal-nem stroju. Mate Eurostyle™ omogoča kontro-liran razrez tudi ko gre za delno prebijanje. Ker je orodje vodeno v primerjavi z standardnim (ne-vodenim) orodjem zdrži do trikrat dlje.

Mate Eurostyle™ orodja niso primerna za novejše modele Trumpf prebijalnih strojev (Tru-matic TC 500 in novejši).

MATE Longlife™5. orodja za razrez so zasnova-na za zagotavljanje najboljših rezultatov. Ker je orodje OEM kompatibilno je primerno tudi za novejše Trumpf prebijalne stroje. Orodje je izdelano iz visoko kakovostnega orodnega jekla M4PM™. Mate Longlife™ vključujejo naslednje sestavne dele: inserni prebijač, držalo prebijača, matrico in vstavke za matrico. Na voljo v štirih oblikah: pravokotnik, oval, trapezoid in pra-vokotnik z izsekom v obliki »lastovičjega repa«.

MATE LongLife™

ZA VEČ INFORMACIJ PRELISTAJTE KATALOG TRUMPF ORODIJ IN ORODNIH SISTEMOV:

MATE PRECISION TOOLING dobavlja tudi “kasete” za TRUMPF® TruPunch prebijalne stroje. Na voljo za modele 200, 500R, 600L, 1000, 2000, 2010L, 2020R, 3000, 3000L, 5000R, 6000L.

Vse kataloge za prebijalno orodje najdete v elektronski obliki na spletni strani www.mate.com, najdete jih na podstrani Product Literature (Home Page > Literature > Product Literature).

Če želite, da vam pošljemo katalog v tiskani obliki nas pokličite na 01/562 00 99 ali pa nam to sporočite prek e-pošte na naslov koplas@siol.net!

SPECIALNA ORODJAZA PREBIJALNE STROJE TRUMPF

Primeri izdelkov s specialnimi orodji

SPECIALNA ORODJA:

V MATE PRECISION TOOLING so specialisti za izdela-vo specialnih orodij. V ponudbi specialnih orodij za Trumpf prebijalne stroje so orodja za: vlečenje, izdelavo vodil za računalniške kartice, markiranje, različne deformacije materiala, iztiskanje, izdelavo členkov tečajev za vratca, orodij za odtis logotipov, številčenje, itd.

Glede na vaše zahteve izdelajo posamezna orod-ja posebnih oblik, veliko izkušenj imajo tudi na področju izdelave cluster orodij.

Prav tako so tudi za Trumpf prebijalne stroje na vol-jo Mate standardna specialna orodja, kot so MATE Rollerball™, MATE Rollerball Deburr™, MATE Sheet-marker™, MATE SnapLock™, MATE HexLock™, MATE EasySanp™ in MATE EasyBend™.

Za več informacij o specialnih orodij nas kontaktirajte!

ZANIMIVO: Na spletni strani http://www.mate.com izberite Fabrication Solutions, kjer se nahaja veliko idej, nasvetov in rešitev za izdelavo posebnih oblik s prebijalnim orodjem.

Za več informacij in podrobnejši vpogled v orodja in sisteme, prelistajte katalog Trumpf orodij in orodnih sistemov!

NO. 368NO. 368

®

®

Countersink-Dedicated Emboss-Continuous CenterpointCard Guide

Emboss-Continuous Emboss-Cold Forged Emboss-FormedSheetmarker®

Extrusion-Tapping Hinge KnockoutPierce and Extrude

Lance and Form Louver-Open End Louver-Closed EndLance and Form1

Stamp-Alpha Numberic

V-Line Inscription ThreadformShearbutton

NO. 368NO. 368

®

®

Countersink-Dedicated Emboss-Continuous CenterpointCard Guide

Emboss-Continuous Emboss-Cold Forged Emboss-FormedSheetmarker®

Extrusion-Tapping Hinge KnockoutPierce and Extrude

Lance and Form Louver-Open End Louver-Closed EndLance and Form1

Stamp-Alpha Numberic

V-Line Inscription ThreadformShearbutton

NO. 368NO. 368

®

®

Countersink-Dedicated Emboss-Continuous CenterpointCard Guide

Emboss-Continuous Emboss-Cold Forged Emboss-FormedSheetmarker®

Extrusion-Tapping Hinge KnockoutPierce and Extrude

Lance and Form Louver-Open End Louver-Closed EndLance and Form1

Stamp-Alpha Numberic

V-Line Inscription ThreadformShearbutton

NO. 368NO. 368

®

®

Countersink-Dedicated Emboss-Continuous CenterpointCard Guide

Emboss-Continuous Emboss-Cold Forged Emboss-FormedSheetmarker®

Extrusion-Tapping Hinge KnockoutPierce and Extrude

Lance and Form Louver-Open End Louver-Closed EndLance and Form1

Stamp-Alpha Numberic

V-Line Inscription ThreadformShearbutton

NO. 368NO. 368

®

®

Countersink-Dedicated Emboss-Continuous CenterpointCard Guide

Emboss-Continuous Emboss-Cold Forged Emboss-FormedSheetmarker®

Extrusion-Tapping Hinge KnockoutPierce and Extrude

Lance and Form Louver-Open End Louver-Closed EndLance and Form1

Stamp-Alpha Numberic

V-Line Inscription ThreadformShearbutton

NO. 368NO. 368

®

®

Countersink-Dedicated Emboss-Continuous CenterpointCard Guide

Emboss-Continuous Emboss-Cold Forged Emboss-FormedSheetmarker®

Extrusion-Tapping Hinge KnockoutPierce and Extrude

Lance and Form Louver-Open End Louver-Closed EndLance and Form1

Stamp-Alpha Numberic

V-Line Inscription ThreadformShearbuttonNO. 368NO. 368

®

®

Countersink-Dedicated Emboss-Continuous CenterpointCard Guide

Emboss-Continuous Emboss-Cold Forged Emboss-FormedSheetmarker®

Extrusion-Tapping Hinge KnockoutPierce and Extrude

Lance and Form Louver-Open End Louver-Closed EndLance and Form1

Stamp-Alpha Numberic

V-Line Inscription ThreadformShearbutton

MATE Rollerball™

MATE EasySnap™

MATE Rollerball Deburr™

MATE Snaplock™

MATE EasyBend™

Orodja za deformacijo

MATE Hexlock™

MATE Sheetmarker™

Orodje MATE Rollerball™ omogoča obdelavo pločevine s kroglicami za vlečenje izbokline.

Orodje MATE Rollerball™ je namen-jeno raziglevanju po prebijanju.

MATE EasyBend™ na tanjših materialih ustvari linijo, ki omogoča, da je kos pločevine mogoče ročno skriviti brez uporabe zapogibnika.

Z orodjem MATE EasySnap™ na materialu ustvarite posebne utore, ki omogočajo zelo enostavno ročno odstranjevanje izdelkov iz celega kosa pločevine.

Mate lahko po naročilu izdela kakršno koli orodje za deformacijo materiala (oblike, logotipi, napisi,...)

Orodje MATE Hexlock™ omogoča izdelavo zapore - držala matric za varovanje proti odpiranju.

Orodje MATE SnapLock™ je namen-jeno izdelavi montažnih spon.

Z orodjem MATE Sheetmarker™ gravirate želene oblike.

Cluster - Shape Card Guide CenterpointCluster - Round

Countersink-Shape Emboss-Beading Emboss-EdgeformCountersink-Round

Emboss-Cold Forged Extrusion-Tapping Extrusion-Flanged HoleEmboss-Formed

Hinge Tool Knockout Lance and FormGuided Shearing

Scissortool® Shearbutton Rollerball®Louver

Stamping-Alpha Numeric

Stamping-V-Line ThreadformSheetmarker®

Cluster - Shape Card Guide CenterpointCluster - Round

Countersink-Shape Emboss-Beading Emboss-EdgeformCountersink-Round

Emboss-Cold Forged Extrusion-Tapping Extrusion-Flanged HoleEmboss-Formed

Hinge Tool Knockout Lance and FormGuided Shearing

Scissortool® Shearbutton Rollerball®Louver

Stamping-Alpha Numeric

Stamping-V-Line ThreadformSheetmarker®

Cluster - Shape Card Guide CenterpointCluster - Round

Countersink-Shape Emboss-Beading Emboss-EdgeformCountersink-Round

Emboss-Cold Forged Extrusion-Tapping Extrusion-Flanged HoleEmboss-Formed

Hinge Tool Knockout Lance and FormGuided Shearing

Scissortool® Shearbutton Rollerball®Louver

Stamping-Alpha Numeric

Stamping-V-Line ThreadformSheetmarker®

KOPLAS PRO d.o.o., Nova Pazova

KOPLAS d.o.o., Ljubljana

Razstavni prostor: INDUSTRIJSKA ZONA BB, 22330 Nova Pazova, Srbija

Razstavni prostor: MOTNICA 11, 1236 Trzin, Slovenija

POKLIČITE NAS NA:

+386 1 562 00 99 +386 1 562 01 00+386 40 466 347

KONTAKTIRAJTE NAS NA:

koplas@siol.net

POKLIČITE NAS NA:

+381 22 323 598+381 22 328 088

+381 63 80 17 132

KONTAKTIRAJTE NAS NA:

office@koplas.co.rs