Upload
others
View
6
Download
2
Embed Size (px)
Citation preview
KOMATSU TRAINING ACADEMY TRAINING CALENDAR 2020
Komatsu Training Academy 1300 390 377
Lead Hydraulics This course provides participants with knowledge of Open Load Sensing (OLSS), Closed Load Sensing (CLSS) and Hydrostatic systems applied to earthmoving and Komatsu equipment. In addition, it will provide an overview of diagnostic techniques with the use of practical training aids and 'real world' situations.
Course outcomes:• Read and interpret schematics
• Understand the technologies used to build hydraulic equipment
• Diagnose and assemble component parts of hydraulic control valves
• Carry out diagnostic techniques safely and in a satisfactory manner
• Understand and perform testing and troubleshooting using various equipment and techniques on machines and hydraulic simulation board
• Identify the correct hydraulic symbols using schematics noting differences in country of origin
Electrical Diagnostic Fundamentals This course is designed to give participants who have trade experience, the necessary technical skills to perform electrical diagnostics. The course is designed to carry the participant through revision of basic electrical fundamentals and their application on machines, testing of batteries, charging and starting systems, sensors, application of sensors and troubleshooting, reading schematics and an introduction to CAN bus.
Course outcomes:• Read and interpret schematics, identify schematic symbols and
troubleshoot faults
• Understand electrical fundamentals including identification of a variety of circuits and their components, analysis of the effects of faults, diagnosis and rectification
• Identify batteries, starting and charging systems, including battery safety requirements and testing
• Carry out correct use of testing equipment, sensor identification and testing and CAN bus topography and testing
Lead Hydraulics Course Information
COURSE DURATION 4 days
DELIVERY MODE Face to Face
COURSE TIMES 8.00am to 4.00pm
DATES31 MAR 2020 – 3 APR 2020 Sherwood (KTEC)
Electrical Diagnostic Fundamentals Course Information
COURSE DURATION 4 days
DELIVERY MODE Face to Face
COURSE TIMES 8.00am to 4.00pm
DATES5 MAY 2020 – 8 MAY 2020 Sherwood (KTEC)
Available Courses
D155AXi-8This course provides people who hold trade qualifications in either automotive, engineering or electrical or equivalent industry experience with the knowledge and skills to understand the overall Bull Dozer design and structure to be able to perform regular periodic maintenance, understand the principles of operation and construction to perform testing and adjusting and basic troubleshooting on the Bulldozers systems and components.
Course outcomes:• Demonstrate compliance with all safety procedures related to
servicing the Komatsu Bull Dozer
• Using the workshop manual obtain information relevant to the operation of system components and specifications
• Explain and locate selected components on the machine
• Locate all service points on the machine and state their service requirement
• Using circuit diagrams show the system operation
• Explain the operating principles of each of the functional machine systems
• Explain the Komatsu recommended procedures for testing of system components
• Perform machine testing to Komatsu recommendations
• Compare test results with Komatsu specifications, and make recommendations
• Use the correct test equipment to trouble-shoot system faults
• Use Komatsu troubleshooting charts to aid in problem resolution
• Correctly diagnose system faults
PC490LCi-11 Course outcomes:• Demonstrate compliance with all safety procedures related to
servicing the Komatsu Excavator
• Locate selected components on the machine
• Locate all service points on the machine and state their service requirement
• Using the Shop Manual obtain information relevant to the operation of components and their specifications
• Using circuit diagrams show the system operation
• Explain the operating principles of each of the functional machine systems
• Carry out safety precautions to be observed when tests and adjustments are conducted
• Explain the Komatsu recommended procedures for testing of system components
• Perform machine testing to Komatsu recommendations
• Compare test results with Komatsu specifications, and make recommendations
• Use the correct test equipment to trouble-shoot system faults
• Use Komatsu troubleshooting charts to aid in problem resolution
• Correctly diagnose system faults
PC490LCi-11 Course Information
COURSE DURATION 4 days
DELIVERY MODE Face to Face
COURSE TIMES 8.00am to 4.00pm
DATES9 JUN 2020 – 12 JUN 2020 Welshpool
D155Axi-8 Course Information
COURSE DURATION 4 days
DELIVERY MODE Face to Face
COURSE TIMES 8.00am to 4.00pm
DATES30 JUN 2020 – 3 JUL 2020 Welshpool
PC600/850LC-8EO This course provides people who hold trade qualifications in either automotive, engineering or electrical or equivalent industry experience with the knowledge and skills to understand the overall Excavator design and structure to be able to perform regular periodic maintenance, understand the principles of operation and construction to perform testing and adjusting and basic troubleshooting on the Excavator systems and components.
Course outcomes:• Demonstrate compliance with all safety procedures related to
servicing the Komatsu Excavator
• Using the workshop manual obtain information relevant to the operation of system components and specifications
• Explain and locate selected components on the machine
• Locate all service points on the machine and state their service requirement
• Using circuit diagrams show the system operation
• Explain the operating principles of each of the functional machine systems
• Explain the Komatsu recommended procedures for testing of system components
• Perform machine testing to Komatsu recommendations
• Compare test results with Komatsu specifications, and make recommendations
• Use the correct test equipment to trouble-shoot system faults
• Use Komatsu troubleshooting charts to aid in problem resolution
• Correctly diagnose system faults
PC210/490LCi-11 This course provides people who hold trade qualifications in either automotive, engineering or electrical or equivalent industry experience with the knowledge and skills to understand the overall Excavator design and structure to be able to perform regular periodic maintenance, understand the principles of operation and construction to perform testing and adjusting and basic troubleshooting on the Excavator systems and components.
Course outcomes:• Demonstrate compliance with all safety procedures related to
servicing the Komatsu Excavator
• Using the workshop manual obtain information relevant to the operation of system components and specifications
• Explain and locate selected components on the machine
• Locate all service points on the machine and state their service requirement
• Using circuit diagrams show the system operation
• Explain the operating principles of each of the functional machine systems
• Explain the Komatsu recommended procedures for testing of system components
• Perform machine testing to Komatsu recommendations
• Compare test results with Komatsu specifications, and make recommendations
• Use the correct test equipment to trouble-shoot system faults
• Use Komatsu troubleshooting charts to aid in problem resolution
• Correctly diagnose system faults
PC600/850LC-8EO Course Information
COURSE DURATION 4 days
DELIVERY MODE Face to Face
COURSE TIMES 8.00am to 4.00pm
DATES18 AUG 2020 – 21 AUG 2020 Sherwood (KTEC)
PC210/490LCi-11 Course Information
COURSE DURATION 4 days
DELIVERY MODE Face to Face
COURSE TIMES 8.00am to 4.00pm
DATES25 AUG 2020 – 28 AUG 2020 Sherwood (KTEC)
Available Courses CONTINUED
PC78/88MR-10 This course provides people who hold trade qualifications in either automotive, engineering or electrical or equivalent industry experience with the knowledge and skills to understand the overall Excavator design and structure to be able to perform regular periodic maintenance, understand the principles of operation and construction to perform testing and adjusting and basic troubleshooting on the Excavator systems and components.
Course outcomes:• Demonstrate compliance with all safety procedures related to
servicing the Komatsu Excavator
• Using the workshop manual obtain information relevant to the operation of system components and specifications
• Explain and locate selected components on the machine
• Locate all service points on the machine and state their service requirement
• Using circuit diagrams show the system operation
• Explain the operating principles of each of the functional machine systems
• Explain the Komatsu recommended procedures for testing of system components
• Perform machine testing to Komatsu recommendations
• Compare test results with Komatsu specifications, and make recommendations
• Use the correct test equipment to trouble-shoot system faults
• Use Komatsu troubleshooting charts to aid in problem resolution
WA200/320-8 This course provides people who hold trade qualifications in either automotive, engineering or electrical or equivalent industry experience with the knowledge and skills to understand the overall HST loader design and structure to be able to perform regular periodic maintenance, understand the principles of operation and construction to perform testing and adjusting and basic troubleshooting on the HST loader systems and components.
Course outcomes:• Demonstrate compliance with all safety procedures related to
servicing the Komatsu HST Loader
• Using the workshop manual obtain information relevant to the operation of system components and specifications
• Explain and locate selected components on the machine
• Locate all service points on the machine and state their service requirement
• Using circuit diagrams show the system operation
• Explain the operating principles of each of the functional machine systems
• Explain the Komatsu recommended procedures for testing of system components
• Perform machine testing and adjusting of hydraulic system components
• Compare test results with Komatsu specifications, and make recommendations
• Use the correct test equipment to trouble-shoot system faults
• Use Komatsu troubleshooting charts to aid in problem resolution
• Correctly diagnose engine and hydrostatic faults
WA200/320-8 Course Information
COURSE DURATION 4 days
DELIVERY MODE Face to Face
COURSE TIMES 8.00am to 4.00pm
DATES18 AUG 2020 – 21 AUG 2020 Welshpool
PC78/88MR-10 Course Information
COURSE DURATION 4 days
DELIVERY MODE Face to Face
COURSE TIMES 8.00am to 4.00pm
DATES29 SEP 2020 – 2 OCT 2020 Sherwood (KTEC)
TLILIC0003 Licence to Operate a Forklift TruckThis unit of competency specifies the skills and knowledge required to operate a forklift truck safely.
Course outcomes:• WH&S legislation
• Risk and hazards
• General inspections and preparation of work site requirements
• Plan and prepare work
• Conduct routine checks and equipment maintenance
• Operate forklift truck
• Shift loads
• Shut down and secure forklift truck
Licence to Operate a Forklift Truck Course Information
COURSE DURATION 3 days
DELIVERY MODE Face to Face
COURSE TIMES 8am to 4.00pm
DATES
7 JUL 2020 – 9 JUL 2020 Sherwood (KTEC)
22 SEP 2020 – 24SEP 2020 Sherwood (KTEC)
HLTAID003 Provide First AidKomatsu Training Academy’s Provide First Aid course complies with the Australian Resuscitation Council (ARC) Guidelines relating to the provision of first aid.
Course outcomes:• The basic ethics and theory involved in first aid practice
• The measures that need to be taken to effectively deal with issues concerning major or minor injury and illness
• The most important management steps that need to be undertaken when dealing with potentially critical conditions
• Basic health and safety knowledge that is required when dealing with first aid situations
• The principles, procedures and standard precautions that need to be undertaken to control infection and its spread
• You will master the knowledge of ‘Chain of Survival’
• You will learn the skills a First Aider requires and what limitations you should be aware of
• How and when an Automated External Defibrillator (AED) should be used
HLTAID003 Provide First Aid Course Information
COURSE DURATION 2 days
DELIVERY MODE Face to Face
COURSE TIMES 8am to 4.00pm
DATES
25 AUG 2020 – 26 AUG 2020 Sherwood (KTEC)
27 OCT 2020 – 28 OCT 2020 Sherwood (KTEC)
Available Courses CONTINUED
For more information call the Komatsu Training Academy 1300 390 377
Komatsu Training Academy 1300 390 377
RTO No: 90996
Form No: ZESB099931_JAN2020