Upload
others
View
98
Download
6
Embed Size (px)
Citation preview
Supporting your complete shotcrete operation.
KING SHOTCRETE EQUIPMENT CANADIAN PARTS CATALOGUE
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 1 |
T A B L E O F C O N T E N T S
ALIVA SHOTCRETE MACHINES 3-5
PUTZMEISTER TK 20 CONCRETE PUMP 6
CCM 200 E CONTINUOUS MIXER 7
CHEMICAL & WATER BOOSTER PUMPS 8
DRY-MIX MACHINE PARTS 9-11
HYDRO-MIX NOZZLES (DRY PROCESS) 12-13
EXTENSION HOSES (DRY PROCESS) 14-15
CONCRETE PUMPING HOSES 16
SNAP COUPLINGS & GASKETS 17
REDUCERS (DRY & WET PROCESS) 18
WET-MIX NOZZLES 19
HOPPER HOOD 20
AIR-SEPARATOR BOX 21
SHOTCRETE CONSTRUCTION PANELS 22
FORM OIL 23
SHOTCRETE SUPPORT POSTS 24
END-BEAM TESTER 25
BULK BAGGED HANDLING PRODUCTS 26
DUST SUPRESSION PRODUCTS 27
SHOTCRETE HELMETS 28
ORDER FORM 29
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 2 |
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 3 |
A L I V A S H O T C R E T E M A C H I N E S
ALIVA AL-237
The Aliva AL-237 shotcrete machine is the ideal machine for small to mid-sized shotcrete applications. Based on the rotor size, the Aliva AL-237 has output capabilities ranging from 0.2 m3 to 4.0 m3 per hour. As such, this machine is ideal for applications such as concrete patchwork and restoration, swimming pool construction, joint filling, slope stabilization, and refractory work.
• The Aliva AL-237 Air Model allows for variable rotor speed, controlled by an air motor
• The Aliva AL-237 Standard Model has a fixed output (ON/OFF)
• The Aliva AL-237 Top Model allows for variable rotor speed, controlled by a Variable Frequency Drive (VFD)* *Electric Drive machines require compressed air for material conveyance
ROTOR SIZE HOSE DIAMETERCONVEYING OUTPUT
MAXIMUM AGGREGATE SIZE
0.7 Litre 32 mm 0.2-0.5 m3/hr 6 mm
2.0 Litre 32 mm or 38 mm 0.6-1.4 m3/hr 12 mm
3.6 Litre 38 mm 1.1-2.5 m3/hr 12 mm
5.6 Litre 50 mm 1.7-4.0 m3/hr 16 mm
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 4 |
A L I V A S H O T C R E T E M A C H I N E S
ALIVA AL-252
The Aliva AL-252 shotcrete machine has been considered the work horse of the mining and tunneling industry for many years. With output ranging from 3.5 m3 to 11.0 m3 per hour, the Aliva AL-252 is ideally suited for high volume, dry-process shotcrete operations. This machine is most commonly used as a stand alone unit, but it can also be integrated into a bulk type shotcrete system when installed on mobile equipment and fed by a bulk hopper.
• The Aliva AL-252 Air Model allows for variable rotor speed, controlled by an air motor
• The Aliva AL-252 Standard Model has a fixed output (ON/OFF)
ROTOR SIZE HOSE DIAMETERCONVEYING OUTPUT
MAXIMUM AGGREGATE SIZE
10 Litre 50 mm 3.5-7.0 m3/hr 16 mm
16 Litre 60 mm 5.5-11.0 m3/hr 20 mm
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 5 |
A L I V A S H O T C R E T E M A C H I N E S
ALIVA AL-101
The Aliva AL-101 is a Quick Connect, mountable spray head for your excavator. This spray head offers an extremely large and flexible range of applications thanks to its simple and rapid assembly on numerous different machines. Whether you are working on excavations, slope stabilization or tunneling, with the Aliva AL-101 spray head, you will always be prepared to apply shotcrete with your own equipment.
• Quick and easy to mount
• For dry and wet mixes
• Connected to excavator hydraulics
• Compatible with any standard quick-release system, rotary machine or concrete pump
• With concrete pump or rotary machine, spray head becomes self-sufficient concrete spraying system
• Variants: 12 VDC (5A), 24 VDC (5A), cable or radio remote control
WEIGHT IN KG
MAX. OUTPUT IN M3/H
HOSE SIZEHYDRAULIC
CONNECTIONHYDRAULIC OIL
PRESSUREHYDRAULIC OIL
FLOW
210 According to conveying machine
Max. DN 65 (6.4 cm/2.5” HD)
P/T = 2.6 cm (1”)
Min. 21 MPa (3045 psi) Max. 35 MPa (5076 psi)
Approx. 15 L/min (4 gl/min)
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 6 |
P U T Z M E I S T E R T K 2 0 C O N C R E T E P U M P
PERFORMANCE DATA
• Maximum Volume Output: 13 m3 (17 yd) per hour
• Maximum Concrete Pressure: 14 MPa (2,085 psi)
• Maximum Aggregate Size: 25 mm (1 inch)
TECHNICAL INFORMATION
• Variable Control: Yes
• Maximum Number of Strokes Per Minute: 28
• Hopper Height: 122 cm (48 inches)
DIMENSIONS
• Length: 375 cm (148 inches)
• Width: 162 cm (64 inches)
• Height: 157 cm (62 inches)
• Weight: 2,177 kg (4,800 lb)
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 7 |
C C M 2 0 0 E C O N T I N U O U S M I X E R
FEATURES AND BENEFITS
• Allows for continuous high-output production; 11 m3 (14.5 yd3) per hour, without interruption
• Large receiving hopper allows for 1,000 kg (2,205 lb) bulk bag capacity
• Exact control (calibrated) of water and material input ensures constant water-to-materials ratio
• Compact and cageable on a four-way steel skid mount, to allow for maneuverability in confined areas
• Removable mixing tube allows for easy cleaning of mixing chamber
• Low charging height of 1.6 m (5.25 ft) including protective hopper enclosure (optional), allows for maximum performance in constricted spaces
USES
For continuous mixing of a wide range of mixtures, including pre-blended, pre-packaged concrete, as well as wet or dry shotcrete and slurries.
OPTIMAL PERFORMANCE
Use of a water booster pump is recommended for applications where water pressue is expected to fluctuate.
PERFORMANCE DATA
Ouput of 11 m3 (14.5 yd3) per hour.
SPECIFICATIONS
• Length
Operating: 3,500 mm (138 inches)
Transport: 1,850 mm (73 inches)
• Width
Operating: 1,200 mm (47 inches)
Transport: 1,200 mm (47 inches)
• Height: 1,800 mm (71 inches)
• Power: 20 HP, 575/3/60
• Weight: 1,500 kg (3,300 lb)
• Mounting: Four-Way Steel Skid
• Water Control: Automatic
The CCM 200 E Continuous Mixer is a high quality, high capacity, easy to operate, concrete mixer with automatic water control, mounted on a four-way steel skid. This mixer addresses all of the technical and practical concerns associated with mixing high quality concrete in underground mining and remote applications.
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 8 |
C H E M I C A L & W A T E R B O O S T E R P U M P S
A-10 A-20
Maximum Output 0-95 L/hr (0-25 gl/hr) 0-454 L/hr (0-120 gl/hr)
Maximum Pressure 0.8 MPa (116 psi) 0.8 MPa (116 psi)
Power Air, Electric, or Hydraulic Air, Electric, or Hydraulic
Mounting Portable Stand Portable Stand
GBP-300 GBP-500
Maximum Output 40 L/min (10.6 gl/min) 76 L/min (20 gl/min)
Minimum Air Pressure 0.2 MPa (29 psi) 0.2 MPa (29 psi)
Maximum Air Consumption 2.27 m³/min (80.0 ft³/min) 2.27 m³/min (80.0 ft³/min)
Length 610 mm (24 inches) 610 mm (24 inches)
Width 330 mm (13 inches) 330 mm (13 inches)
Height 305 mm (12 inches) 305 mm (12 inches)
Weight 25 kg (56 lb) 25 kg (56 lb)
The A-10 Chemical/Accelerant Dosing Pump handles abrasive fluids with little wear and provides a high level of volumetric accuracy for sampling, transfer, and metering applications. The A-20 Chemical/Accelerant Dosing Pump has no valves or glands where crystals can build up or clog the pump. The absence of product slip in the hose provides 100 percent volumetric efficiency.
CHEMICAL/ACCELERANT PUMPS
WATER BOOSTER PUMPS
Air-driven water booster pumps, such as the GBP-300 and the GBP-500, work on a reciprocating differential area piston principle. The water pressure can vary from zero to 3.4 MPa (500 psi).
GBP 300 Water Booster Pump shown here
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 9 |
D R Y - M I X M A C H I N E P A R T S
Aliva OEM joint plates and rotor plates are constructed with the highest quality of rubber and high carbon steel, which allows for increased throughput and lower operating costs. Both the joint plates and rotor plates can be ground-down several times and then put back in operation. This process should be completed before the wear on the plates becomes too severe.
ALIVA AL-237/246
ALIVA AL-237/246 AIR OUTLET CHAMBERS
ALIVA AL-252
ALIVA AL-252 AIR OUTLET CHAMBER
PART # DESCRIPTION
246.2043 Lower Joint Plate
246.2047 Upper Joint Plate
246.0252 Rotor Plate
246.0254 Rotor Plate Gasket
PART # DESCRIPTION
246.0380 Air Outlet Chamber 38 mm (1½”)
246.0285 Air Outlet Chamber 50 mm (2”)
PART # DESCRIPTION
260.0233 Lower Joint Plate
260.0244 Upper Joint Plate
260.0237 Rotor Plate
PART # DESCRIPTION
252.0010 Air Outlet Chamber 60 mm (2⅜”)
250.0077 Outlet gasket
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 1 0 |
ALIVA AL-252 HOSE INSERTS
AIR MOTOR SILENCERS
ALLENTOWN MEYCO PICCOLA DISCHARGE LINERS
LUBRICATION HOSE FOR WEAR PADS
PART # DESCRIPTION
260.0506 Hose Insert 10 Litre
260.0526 Hose Insert 16 Litre
PART # DESCRIPTION
255.0023 Aliva AL-252
255.0025 Aliva AL-237/AL-246 & Piccola
PART # DESCRIPTION
A76033 Discharge Liner
A76034 Outlet Spout Liner 1½”
A76035 Outlet Spout Liner 1¼”
A76036 Outlet Spout Liner 1”
PART # DESCRIPTION
800.0093 Lubrication Hose
AIR PRESSURE GAUGE
PART # DESCRIPTION
150.0276 Pressure Gauge
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 1 1 |
ALLENTOWN MEYCO PICCOLA FRICTION DISCS
ALLENTOWN MEYCO PICCOLA PADS
ALIVA AL-246 & AL-252 SIEVE
KINK PROTECTOR & NOZZLE HOLDER
ALIVA AL-246 & AL-252 HOPPER VIBRATOR
ALIVA AL-252 AGITATOR & CABLE
PART # DESCRIPTION
A76136 Upper Wear Pad
A76140 Bottom Wear Pad
PART # DESCRIPTION
A76033 Friction Disc, 9 Hole Round
A76034 Friction Disc, 12 Hole Round
A76035 Friction Disc, 12 Hole Pie
PART # DESCRIPTION
838.0058 Vibrator
PART # DESCRIPTION
840.0099 Large Hole Sieve
PART # DESCRIPTION
252.0015 Agitator
246.0086 Wire Cable
PART # DESCRIPTION
220.0370 Kink Protector
220.2442 Nozzle Holder
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 1 2 |
H Y D R O - M I X N O Z Z L E S ( D R Y P R O C E S S )
The semi-wet, or hydro-mix, nozzle assembly was designed to increase mixing time after the introduction of water in the dry-mix process. This increase in time allows for more thorough mixing before the shotcrete exits the nozzle, and greatly reduces dust emissions from the nozzle tip.
ITEM PART # QUANTITY DESCRIPTION
Full assembly 220.1555 1 Full assembly
1 220.1561 1 Nozzle 38
2 220.1562 1 Hose Coupling w/Dist. 38
3 180.1819 16 Screw
4 170.0012 3 M 38/58 Material Hose
5 220.1563 1 Threaded Coupling
6 220.1566 1 Water Ring 38
7 220.1564 1 Water Inlet Piece
8 220.2774 1 Threaded Flange
9 170.0027 1 2½” Coupling
10 125.0342 2 O Ring
11 110.3688 1 Needle Valve
38/58 (1½”) INSIDE DIAMETER HOSE
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 1 3 |
50/70 (2’) INSIDE DIAMETER HOSE
60/80 (23/8”) INSIDE DIAMETER HOSELONG NOZZLES
ITEM PART # QUANTITY DESCRIPTION
Full assembly 220.1615 1 Full assembly
1 220.1621 1 Nozzle 50
2 220.1622 1 Hose Coupling w/Dist. 50
3 180.1819 16 Screw
4 170.0016 3 M 50/70 Material Hose
5 220.1623 1 Threaded Coupling
6 220.1625 1 Water Ring 50
7 220.1624 1 Water Inlet Piece
8 820.1623 1 Threaded Flange
9 170.0028 1 3” Coupling
10 125.0346 2 O Ring
11 110.3688 1 Needle Valve
ITEM PART # QUANTITY DESCRIPTION
Full assembly 220.1665 1 Full assembly
1 220.1671 1 Nozzle 60
2 220.1672 1 Hose Coupling w/Dist. 60
3 180.1819 16 Screw
4 170.0018 3 M 60/80 Material Hose
5 220.1673 1 Threaded Coupling
6 220.1675 1 Water Ring 60
7 220.1724 1 Water Inlet Piece
8 820.1673 1 Threaded Flange
9 170.0028 1 3” Coupling
10 125.0351 2 O Ring
11 110.3688 1 Needle Valve
PART # DESCRIPTION
220.1610 36” Nozzle 50/70 (2”)
820.1671 36” Nozzle 60/80 (2⅜”)
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 1 4 |
E X T E N S I O N H O S E S ( D R Y P R O C E S S )
King Shotcrete Equipment’s high quality mandrel-made, dry-process shotcrete hose is available in varying diameters and lengths. Our extension hoses are complete with a quick-connect, snap clamp for ease of assembly.
ITEM PART # QUANTITY DESCRIPTION
1 220.0041 2 Hose End 38
2 170.0012 0-20 38/58 (1½”) Material Hose
3 180.1819 16 Screw
4 170.0027 1 2½” Coupling
10 M Assembly 220.0045 1 Extension Hose Assembly 38/58 (1½”) x 10 M
20 M Assembly 220.0040 1 Extension Hose Assembly 38/58 (1½”) x 20 M
38/58 (1½”) INSIDE DIAMETER HOSE
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 1 5 |
50/70 (2”) INSIDE DIAMETER HOSE
10 M Assembly 220.0052 1 Extension Hose Assembly 50/70 (2”) x 10 M
20 M Assembly 220.0050 1 Extension Hose Assembly 50/70 (2”) x 20 M
ITEM PART # QUANTITY DESCRIPTION
1 220.0051 2 Hose End 50
2 170.0016 0-20 50/70 (2”) Material Hose
3 180.1819 16 Screw
4 170.0028 1 3” Coupling
ITEM PART # QUANTITY DESCRIPTION
1 220.0061 2 Hose End 60
2 170.0018 0-20 60/80 (2⅜”) Material Hose
3 180.1819 16 Screw
4 170.0028 1 3” Coupling
10 M Assembly 220.0062 1 Extension Hose Assembly 60/80 (2⅜”) x 10 M
20 M Assembly 220.0060 1 Extension Hose Assembly 60/80 (2⅜”) x 20 M
60/80 (23/8”) INSIDE DIAMETER HOSE
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 1 6 |
C O N C R E T E P U M P I N G H O S E S
King Shotcrete Equipment’s wet-process, concrete placement hose is available in fabric or steel-braid construction, and with inside diameters ranging from 1½” (38 mm) to 5” (127 mm). Each inner liner is made of natural rubber, and the outer cover is made up of a combination of natural and synthetic rubber that provides superior protection against the elements.
INSIDE DIAMETER
OUTSIDE DIAMETER
NUMBER OF PLIES
WORKING PRESSURE
BURST PRESSURE WEIGHT
1½” (38 mm) 2.20” (56 mm) 4 1,000 psi (6.9 MPa) 2,400 psi (16.5 MPa) 1.05 lb/ft (1.56 kg/m)
2” (51 mm) 2.76” (70 mm) 4 1,000 psi (6.9 MPa) 2,400 psi (16.5 MPa) 1.39 lb/ft (2.07 kg/m)
2½” (63 mm) 3.31” (84 mm) 4 1,000 psi (6.9 MPa) 2,000 psi (13.8 MPa) 1.80 lb/ft (2.68 kg/m)
3” (76 mm) 4.01” (102 mm) 6 1,000 psi (6.9 MPa) 2,000 psi (13.8 MPa) 2.82 lb/ft (4.20 kg/m)
3½” (89 mm) 4.64” (118 mm) 6 1,000 psi (6.9 MPa) 2,000 psi (13.8 MPa) 3.64 lb/ft (5.42 kg/m)
4” (102 mm) 5.12” (130 mm) 6 1,000 psi (6.9 MPa) 2,000 psi (13.8 MPa) 4.00 lb/ft (5.95 kg/m)
4½” (114 mm) 5.59” (142 mm) 6 1,000 psi (6.9 MPa) 2,000 psi (13.8 MPa) 4.36 lb/ft (6.49 kg/m)
INSIDE DIAMETER
OUTSIDE DIAMETER
NUMBER OF PLIES
WORKING PRESSURE
BURST PRESSURE WEIGHT
2” (51 mm) 2.76” (70 mm) 2 1,300 psi (8.9 MPa) 2,900 psi (20.0 MPa) 1.77 lb/ft (2.63 kg/m)
2½” (63 mm) 3.43” (87 mm) 4 1,300 psi (8.9 MPa) 2,600 psi (17.9 MPa) 2.66 lb/ft (3.96 kg/m)
3” (76 mm) 3.90” (99 mm) 4 1,300 psi (8.9 MPa) 2,600 psi (17.9 MPa) 3.24 lb/ft (4.82 kg/m)
4” (102 mm) 5.12” (130 mm) 4 1,300 psi (8.9 MPa) 2,600 psi (17.9 MPa) 5.27 lb/ft (7.84 kg/m)
5” (127 mm) 6.10” (155 mm) 4 1,300 psi (8.9 MPa) 2,600 psi (17.9 MPa) 6.39 lb/ft (9.51 kg/m)
FABRIC BRAID HOSE
STEEL BRAID HOSE
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 1 7 |
S N A P C O U P L I N G S & G A S K E T S
DESCRIPTIONCOMPLETE PART #
GASKET PART #
2½” (64 mm) 170.0027 170.0041
3” (76 mm) 170.0028 170.0042
4” (102 mm) 170.0029 170.0043
DESCRIPTIONCOMPLETE PART #
GASKET PART #
1½” (38 mm) A23730 A23731
2” (51 mm) A23138 A23139
2½” (64 mm) A23195 A23196
3” (76 mm) A23140 A23141
4” (102 mm) A23142 A23143
5” (127 mm) A23144 A23145
DRY PROCESS COUPLINGS
WET PROCESS COUPLINGS
King Shotcrete Equipment supplies various styles and sizes of quick-connect snap couplings and gaskets, for both wet and dry shotcrete processes. Our inventory includes grooved and heavy-duty style clamps and fittings.
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 1 8 |
R E D U C E R S ( D R Y & W E T P R O C E S S )
DESCRIPTION MACHINE PART #
Reducer 50/38 (2”/1½”) AL-246.5 220.0201
Reducer 60/50 (2⅜/2”) AL-252.1 252.0053
Reducer 75/60 (3”/2⅜”) AL-262/263/285 220.0283
DESCRIPTION GASKET PART #
2” x 1½” x 18” (51 mm x 38 mm x 457 mm) HD A23679
2½” x 2” x 28” (64 mm x 51 mm x 711 mm) HD A23328
3” x 2” x 90° Elbow (76 mm x 51 mm x 90°) HD A23793
3” x 2” x 36” (76 mm x 51 mm x 914 mm) HD A23100
3” x 2½” x 12” (76 mm x 64 mm x 305 mm) HD A23851
3” x 2½” x 28” (76 mm x 64 mm x 711 mm) HD A23207
4” x 3” x 90° Elbow (102 mm x 76 mm x 90°) HD A23797
4” x 3” x 36” (102 mm x 76 mm x 914 mm) HD A23200
5” x 4” x 90° Elbow (127 mm x 102 mm x 90°) HD A23791
5” x 4” x 36” (127 mm x 102 mm x 914 mm) HD A23682
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 1 9 |
W E T - M I X N O Z Z L E S
King Shotcrete Equipment carries a wide variety of wet-process nozzles for applications ranging from handheld spraying to the use of remote spray arms. Each nozzle type is available with or without an accelerator inlet, to cater to various applications.
PART # DESCRIPTION
A23348 1½” (38 mm) Shotcrete Nozzle with Accelerator Valve
A23349 1½” (38 mm) Shotcrete Nozzle without Accelerator Valve
A23725 2” (51 mm) Shotcrete Nozzle without Accelerator Valve
A23729 2” (51 mm) Shotcrete Nozzle with Accelerator Valve
ACME NOZZLE ASSEMBLY
PART # DESCRIPTION
A76016 2” (51 mm) HP Nozzle Assembly
A76019 2½” (64 mm) HP Nozzle Assembly
HP NOZZLE ASSEMBLY
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 2 0 |
H O P P E R H O O D
King Shotcrete Equipment’s enclosed hopper hood was developed to serve various purposes. First and foremost, it allows the machine operator to safely open the discharge chute on bulk bags, without lowering the bulk bag on to the lip of the hopper. By opening the access door on the side of the hopper hood, the operator can safely and effectively untie the bags without risk of injury.
Another benefit of the enclosed hopper hood is dust control. Incorporated into the design, is a round hole that is the same diameter as the discharge chute on the bag. This feature allows the chute of the bulk bag to plug the hole in the hood, and prevents dust from escaping from the hopper.
The enclosed hopper hood is available in steel or aluminum, and is designed to fit Aliva AL-237, Aliva AL-246, and Aliva AL-252 machines. Custom hoods for other models are available upon request.
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 2 1 |
A I R - S E P A R A T O R B O X
The purpose of an air-separator box is to allow for concrete to be mixed and placed using a conventional shotcrete machine. The problem with using a standard type shotcrete nozzle to pour a slab or floor, is that the material impacts the surface at a high velocity. As a result of this velocity, aggregate will not adhere to the surface until a layer of paste has built-up. This type of rebound can create pockets of aggregate that exist without cement, which causes voids within the concrete.
An air-separator box is designed to stop the material from impacting the surface with any substantial velocity. The box is lined with thick rubber to reduce wear and decrease velocity. The air-separator box is also equipped with a vent on the top, to allow the conveyance air to escape without pushing the material out of the bottom of the box.
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 2 2 |
S H O T C R E T E C O N S T R U C T I O N P A N E L S
King Shotcrete Equipment shotcrete construction panels are widely used for underground shotcrete construction work. Typical applications include the creation of ventilation barricades, refuge station walls, fuel bay contaminate dikes, backfill barricades, ore and waste-pass bumper walls and powder magazines. By eliminating the need for framework, King Shotcrete Equipment shotcrete construction panels reduce direct material, labour, and material handling costs.
Our panels are made up of five inner trusses of 6 gauge wire, and two full sheets of 9 gauge mesh. The end result is a superior panel, with large openings to facilitate placing on anchor pins. The panels also have a wide enough grid to reduce the amount of rebound that is associated with other panels.
King Shotcrete Equipment shotcrete construction panels are available in standard 4’ (1.2 m) x 8’ (2.4 m) sheets, in various thicknesses ranging from 2” (5 cm) to 8” (23 cm), and can be supplied with or without fabrene backing.
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 2 3 |
F O R M O I L & C O N C R E T E P U M P I N G A I D
The Innoltek FORM-TEK agent was designed to combine the performance of traditional petroleum-based products with greener characteristics. We believe that the new generation of industrial products must be respectful of the environment and can also exceed the expectations of our customers.
FORM-TEK is a biodegradable form release agent that is made from 100% renewable products, and is specially formulated to be used at low temperatures. This product is also water soluble, making it easy to clean. This form release agent is non-toxic, contains no solvents or VOCs, can be used on structures near water, and is safe for workers to use.
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 2 4 |
S H O T C R E T E S U P P O R T P O S T S
King Shotcrete Equipment shotcrete support posts are prefabricated concrete posts designed to take the place of pillars that are shot-in-place using conventional methods. The posts are designed as a quick and effective method for installing support in large excavations underground. They are commonly used in the cut-and-fill mining method, and take the place of ore pillars that are costly to leave in place.
Each shotcrete support post is available with a rebar strain meter cast into the middle of the post. This feature allows for the user to monitor the load applied to the pillar.
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 2 5 |
E N D - B E A M T E S T E R
The end-beam testing apparatus measures the early age, compressive strength of institu concrete or shotcrete. Particularly in mining and tunneling operations, it is important to know the strength of material at early ages. These compressive strength values cannot be obtained through traditional methods such as shooting a panel and retrieving cores, because cores are difficult to extract at an early age and it is not recommended to core a shotcrete panel before a strength of 10 MPa (1,450 psi) has been achieved.
The key to the end-beam test method is the use of molds that can be disassembled for quick and easy extraction at any strength. The test is an adaptation of the ASTM C 116, “Standard Test Method for Compressive Strength of Concrete Using Portions of Beams Broken in Flexure”. The King Shotcrete Equipment End-Beam Tester allows users to obtain quick, easy, and accurate early age strength readings for shotcrete and concrete.
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 2 6 |
B U L K B A G G E D H A N D L I N G P R O D U C T S
LIFTING CROSS
Used in conjunction with a jib boom, overhead crane or other type of hoist, the lifting cross allows for quick attachment of KING’s 1,000 kg (2,205 lb) bulk bags to the lifting device. Due to its design, which utilizes a round bar where the straps are connected, it greatly reduces the chance of straps getting ripped or damaged. This job boom is a smart alternative to using chains or placing directly on to the forks of a forklift.
JIB BOOM
Designed for specific types of forklifts, the jib boom allows shotcrete bags to be lifted higher in areas with low, overhead height. By mounting the jib boom on to the mast of the forklift at an upward angle, this device allows bags to be lifted considerably higher than when simply using forks alone.
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 2 7 |
D U S T S U P R E S S I O N P R O D U C T S
This nozzle combines compressed air and water, to create a mist through each of its nine nozzles. The mist travels with the mine or tunnel ventilation system, capturing airborne dust particles in water droplets, causing the particles to be brought to the ground with the water droplets.
TERRAMIN TERRABLAST 9X8 CLUSTER NOZZLE
MODEL Terrablast 9×8 Cluster Nozzle
MATERIAL Black PVC Frame Retardant Anti-Static (FRAS)
NOZZLE SIZE 9 x 8 mm (0.31″) Cluster
DIMENSIONS 20 cm (8.0″) x 50 cm (19.7″)
MASS 4.7 kg (10.4 lb)
TERRAMIN TERRABLAST WATER ATOMISER
MODEL Single Blast (AM082)
MATERIAL Black PE Housing (FRAS)
NOZZLE SIZE 8 mm (0.31”)
DIMENSIONS 51 cm (20”) length x 20 cm (8”) diameter
MASS 3.2 kg (7 lb)
KING FABRICATING SPRAY BAR
Designed with an arch shape for large openings, the aluminum spray bar has eight spray tips to create a mist across large openings.
This atomiser works by combining compressed air and water to create small water droplets that travel with the mine ventilation system, capturing airborne dust particles and causing them to fall with the water droplet. The air and water are adjusted until the optimum water atomisation OCCURS. This piece of equipment is set-up in locations where dust is commonly emitted, allowing for dust control at its source.
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 2 8 |
S H O T C R E T E H E L M E T S
These shotcrete helmets are fully NIOSH Approved respiratory protection and conform to both ANSI and European Standards for head protection. They provide full mobility, safety and comfort. Additionally, they have a built-in, rechargeable, battery-powered fans and replaceable filters.
The fully enclosed helmet provides benefits beyond the half mask respirator. It provides fresh air supplied by a built-in fan and powered by re-chargeable batteries also built into the helmet. The visor provides eye protection with a wide range of vision and tear-off lenses for ease of cleaning.
PART # DESCRIPTION
M5000 Complete Helmet (including battery charger)
M5001 HEPA Filter
M5002 Fixed Visor/Shield
M5003 Nylon Neck Collar
M5005 Tear-Off Visor (individual)
M5006 Tear-Off Visor (pack of 100)
M5007 Replacement Fan
M5012 Battery Charger
M5014 Replacement Battery
KING SHOTCRETE EQUIPMENT | CANADIAN PARTS CATALOGUE | 2 9 |
O R D E R F O R M
KING SHOTCRETE EQUIPMENT 644 Simmons Rd. P.O. Box 938 Dowling, ON P0M 1R0 Canada To order parts, simply fill out the attached form and fax it to 1(705)855-1122 or e-mail it to [email protected]. Bill to: Ship to: Shipping Instructions: Preferred Carrier: Account Number: Pre-Pay and Charge: Special Instructions:
QTY PART # DESCRIPTION PRICE
TOTAL Notes or Comments:
Sudbury Office644 Simmons Rd. Dowling, ONP0M 1R0Phone: (705) 855-1155Fax: (705) 855-1122
Supporting your complete shotcrete operation.
K I N G S H OT C R E T E E Q U I P M E N T
www.kingshotcrete-equip.com/can • [email protected]