Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
www.polycon.co.uk0151 422 9747
Technical Data Sheet
Galvanised Edge Channel /Stainless Steel Edge Channel
Channel DrainageA15 to E600 loading
Level Invert or Sloped
KE - 150
Polycon Surface Water Drainage | KE - 150 Technical Brochure1 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk
Stepped, Level, SlopedArea drainage with channel runs is normally made according to 3 different principles. The slops of water surface is achieved by the natural fall of the land. The water flows downwards with the gradient of the water level. A stepped invert is realised by an artificial gradient which is formed by the installation of stepped-height channels and connectors. The high flow rate with self-cleaning effect can be achieved with channels in natural slope. All slope types can be combined acording to hydraulic requirements and topographical conditions.
Stepped Invert
Level Invert
Sloped Invert
Technical Data SheetKE - 150
According to DIN 19580 / EN 1433 “Drainage channels for vehicular and pedestrian areas”, these surfaces are assigned to specific load classes depending on the use. Accordingly, the respective suitable Polycon reinforced edge system can be selected with the corresponding cover grating.
Also available in black cataphoretic dip coating
KE - 150Galvanised Steel / Stainless Steel edge rail
Channel Properties
Polymere concrete: Polyester resin-based with minergal aggregates, additives
Compressive strength: > 90 N/mm²
Bending tensile strength: > 22 N/mm²
Modulus of elasticity: ca. 25 kN/mm²
Density: 2.1 - 2.3 g/dm³
Heat resistence: 100°C (permenant loading)
Frost resistence: -50°C
Water penetration depth: 0mm
Water absorption 0.05%
Edge protection: Galvanised steel, stainless steel, profile thickness 6mm or cataphoretic black
Channel cover: Galvanised steel, V2A stainless steel, GJS cast-iron
1000mm214mm
h
500mm214mm
h h
1000mm
hh
214mm
Polycon Surface Water Drainage | KE - 150 Technical Brochure2 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk
Technical Data SheetKE - 150
KE - 150Channel Types Galvanised Steel / Stainless Steel edge rail
Article no. DesignationSlope
%
Length
cm
Width
cm
Height
(h)cm
Weight
kg
KE.150.0 KE - 150 Channel No. 0* 0 100 21.4 22.0 33.0
KE.150.0R KE - 150 Channel No. 0R*** 0 100 21.4 22.0 33.0
KE.150.005 KE - 150 Channel No. 005*/** 0 50 21.4 22.0 17.9
KE.150.1 KE - 150 Channel No. 1* 0.5 100 21.4 22.0 30.3
KE.150.2 KE - 150 Channel No. 2* 0.5 100 21.4 23.0 30.6
KE.150.3 KE - 150 Channel No. 3* 0.5 100 21.4 23.5 30.9
KE.150.4 KE - 150 Channel No. 4* 0.5 100 21.4 24.0 31.2
KE.150.5 KE - 150 Channel No. 5* 0.5 100 21.4 24.5 31.5
KE.150.6 KE - 150 Channel No. 6* 0.5 100 21.4 25.0 31.8
KE.150.7 KE - 150 Channel No. 7* 0.5 100 21.4 25.5 32.1
KE.150.8 KE - 150 Channel No. 8* 0.5 100 21.4 26.0 32.4
KE.150.9 KE - 150 Channel No. 9* 0.5 100 21.4 26.5 32.7
KE.150.10 KE - 150 Channel No. 10* 0.5 100 21.4 27.0 33.0
KE.150.010 KE - 150 Channel No. 010* 0 100 21.4 27.0 35.6
KE.150.010R KE - 150 Channel No. 010R*** 0 100 21.4 27.0 36.5
KE.150.0105 KE - 150 Channel No. 0105*/** 0 50 21.4 27.0 19.0
KE.150.11 KE - 150 Channel No. 11* 0.5 100 21.4 27.5 35.5
KE.150.12 KE - 150 Channel No. 12* 0.5 100 21.4 28.0 35.8
KE.150.13 KE - 150 Channel No. 13* 0.5 100 21.4 28.5 36.1
KE.150.14 KE - 150 Channel No. 14* 0.5 100 21.4 29.0 36.4
KE.150.15 KE - 150 Channel No. 15* 0.5 100 21.4 29.5 36.7
KE.150.16 KE - 150 Channel No. 16* 0.5 100 21.4 30.0 37.0
KE.150.17 KE - 150 Channel No. 17* 0.5 100 21.4 30.5 37.3
KE.150.18 KE - 150 Channel No. 18* 0.5 100 21.4 31.0 37.6
KE.150.19 KE - 150 Channel No. 19* 0.5 100 21.4 31.5 37.9
KE.150.20 KE - 150 Channel No. 20* 0.5 100 21.4 32.0 38.2
KE.150.020 KE - 150 Channel No. 020* 0 100 21.4 32.0 38.6
KE.150.020R KE - 150 Channel No. 020R*** 0 100 21.4 32.0 38.6
KE.150.0205 KE - 150 Channel No. 0205*/** 0 50 21.4 32.0 20.9
KE.150.150P KE- 150 Channel No. 150P**** 0 100 21.4 13.0 20.1
KE.150.150PR KE - 150 Channel No. 150PR***** 0 100 21.4 13.0 20.1
* Channel with mouldings for vertical outlet DA/0D 110** Channel with sidewise perforations for the connection of t-junctions, elbow joints and cross- over joints and vertical outlet*** Channel with vertical pipe socket DA/OD 110
Polycon Surface Water Drainage | KE - 150 Technical Brochure3 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk
Channel available in both Galvanised Steel or Stainless Steel
Technical Data SheetKE - 150
Polycon Surface Water Drainage | KE - 150 Technical Brochure4 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk
The KE - 150 system has a complete range of
accessories including a Sump Unit & Galvanised
bucket which can collect silt particles and has 110mm
and 160mm outlets for pipe connections
The system also has end caps and end cap outlets
with a 110mm pipe connector
Also available in black cataphoretic dip coating
KE - 150Sump & Accessories
Article no. DesignationLength
cm
Width
cm
Height
(h)cm
Weight
kg
KE.150.S KE - 150 Sump unit with dirt trap bucket 50 21.4 62 54.0
KE.150.PP.160 Pipe socket DA/OD 160 0.6
KE.150.PP.200 Pipe socket DA/OD 200 0.8
KE.150.CE.0205 KE - 150 Closed end cap for channel No. 0 - 0205 1.5
KE.150.CE.0 KE - 150 Closed end cap for channel No. 0 1.9
KE.150.CE.150P KE - 150 Closed end cap for channel No. 150-P 1.3
KE.150.EP.0 KE - 150 end cap with Pipe socket DA/OD 160 for No. 0 1.5
KE.150.EP.010 KE - 150 end cap with Pipe socket DA/OD 160 for No. 010 1.5
KE.150.EP.020 KE - 150 end cap with Pipe socket DA/OD 160 for No. 020 2.0
KE.150.EP.150P KE - 150 end cap with Pipe socket DA/OD 70 for No. 150P 1.5
KE.150.STEP KE - 150 Step connector for compensating level differences 0.5
h
500mm214mm
h
214mm
h
20mm
Accessories available in both Galvanised Steel or Stainless Steel
Technical Data SheetKE - 150
Polycon Surface Water Drainage | KE - 150 Technical Brochure5 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk
Slotted Grating OvalGrip Design
Article no. DesignationLength
cm
Width
cm
Inlet Ø
cm²/m
Weight
kg
GR.150.MG.A Mesh grating. galvanised steel. MW 30 x 10 100 20 1240 9.8
GR.150.MG.A Mesh grating, galvanised steel, MW 30 x 10 50 20 1240 4.4
GR.150.MSS.A Mesh grating, stainless steel, MW 20 x 20 100 20 1240 9.5
GR.150.MSS.A Mesh grating, stainless steel, MW 20 x 20 50 20 1240 4.9
Gratings cl. C250 with SnapLock fastening
Mesh Steel Grating Slotted Grating SafeHeel
Longitudinal Grating
KE - 150Gratings
Article no. DesignationLength
cm
Width
cm
Inlet Ø
cm²/m
Weight
kg
GR.150.MG.D Mesh grating, galvanised steel, MW 20 x 20 100 20 1240 9.8
GR.150.MG.D Mesh grating, galvanised steel, MW 20 x 20 50 20 1240 4.4
GR.150.MSS.D Mesh grating, stainless steel, MW 20 x 20 100 20 1240 9.5
GR.150.MSS.D Mesh grating, stainless steel, MW 20 x 20 50 20 1240 4.9
GR.150.ODI.D Slotted grating + OvalGrip Design, Ductile Iron, GJS 50 20 760 7.1
GR.150.LDI.D Longitudinal Grating, Ductile Iron , MW 25 x 11 mm 50 20 700 7.8
GR.150.SSDI.D Slotted SafeHeel Grating, Ductile Iron 50 20 700 7.6
Gratings cl. D4001 with SnapLock fastening
1 Exception: Cross-road drainage of busy roads
Technical Data SheetKE - 150
Polycon Surface Water Drainage | KE - 150 Technical Brochure6 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk
The SnapLock fastening is used for gratings for channels with nominal widths of 150 and 200 mm. SnapLock fastenings are optimised for the respective load class and combine safety and quality with functional design.
• Put in place - press on - snap in place
• Assembly without special tools
• Impervious to transverse forces
• Non-corrosive stainless steel springs
• Reliable function even when heavily soiled
• Grating and channel body intermesh to
form a sturdy unit
Benefits
SnapLock fastening
Technical Data SheetKE - 150
Article no. DesignationLength
cm
Width
cm
Inlet Ø
cm²/m
Weight
kg
GR.150.MG.D Longitudinal Grating, Ductile Iron , MW 25 x 11 mm 100 20 1240 7.8
GR.150.MG.D Slotted SafeHeel Grating, Ductile Iron 50 20 1240 4.4
Gratings cl. E6001 with SnapLock fastening
1 Exception: Cross-road drainage of busy roads
KE - 150
PaveSlotOur Paveslots are specifically designed for intergration in high quality natural stone and paving surfaces. The discrete inlet slot enables effecient drainage without caccess trays for cleaning purposes.
Polycon Surface Water Drainage | KE - 150 Technical Brochure7 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk
All Polycon Paveslots come with either an offset slot or a centre slot aswell as having the choice of a twin slot or single slot
Available in both Glavanised Steel and Stainless Steel
KE - 150PaveSlot
Our Paveslots are specifically designed for intergration in high quality natural stone and paving surfaces. The discrete inlet slot enables effecient drainage without compromising the ground design. We offer both single & twin slotted paveslots aswell as access trays for maintenance purposes.
10mm
200mm
10mm
Offet Single Galvanised or Stainless Steel PaveSlot
1000mm
A Galvanised or Stainless Steel single slot paveslot grating with a width of 200mm, available in either a 60, 105 or 150mm upstand.
60, 105, or 150mm Upstand
Centre Single Galvanised or Stainless Steel PaveSlot
A Galvanised or Stainless Steel single slot paveslot grating with a width of 200mm, available in either a 60, 105 or 150mm upstand.
60, 105, or 150mm Upstand
10mm
200mm
1000mm
10mm
C250, D400Loading Upstand 60, 105 or 150
Polycon Surface Water Drainage | KE - 150 Technical Brochure8 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk
Width 200 mm mm
C250, D400Loading Upstand 60, 105 or 150Width 200 mm mm
60, 105 or 150 mm
60, 105 or 150 mm
KE - 150PaveSlot
60, 105 or 150 mm
Offset Twin Galvanised or Stainless Steel PaveSlot
A Galvanised or Stainless Steel Twin slot paveslot grating with a width of 200mm, available in either a 60, 105 or 150mm upstand.
Polycon Surface Water Drainage | KE - 150 Technical Brochure9 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk
C250, D400Loading Upstand 60, 105 or 150Width 200 mm mm
60, 105, or 150mm Upstand
2 x 8mm
200mm
1000mm
Slots
60, 105 or 150 mm
Centre Twin Galvanised or Stainless Steel PaveSlot
A Galvanised or Stainless Steel Twin slot paveslot grating with a width of 200mm, available in either a 60, 105 or 150mm upstand.
C250, D400Loading Upstand 60, 105 or 150Width 200 mm mm
60, 105, or 150mm Upstand
200mm
1000mm
Slots
2 x 8mm Slots
2 x 8mm
Slots2 x 8mm
KE - 150PaveSlot
Galvanised or Stainless Steel Access Tray
A Galvanised or Stainless Steel single slot paveslot grating with a width of 178mm, available in either a 60, 105 or 150mm upstand.
200mm
500mm
Polycon Surface Water Drainage | KE - 150 Technical Brochure10 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk
60, 105, or 150mm Upstand
C250, D400Loading Upstand 60, 105 or 150Width 200 mm mm
Top View
60, 105 or 150 mm
End View
10mm
Article no. Designation Upstand Height (mm)
Overall Width (mm)
Slot Width (mm)
Length (cm)
Load Class
Weight (kg)
OS.1560.P.G Galvanised Offset Single PaveSlot 60 60 200 10 50/100 C, D 4.2
OS.15105.P.G Galvanised Offset Single PaveSlot 105 105 200 10 50/100 C, D 7.5
OS.15150.P.G Galvanised Offset Single PaveSlot 150 150 200 10 50/100 C, D 10.7
OS.1560.P.SS Stainless Steel Offset Single PaveSlot 60 60 200 10 50/100 C, D 4.4
OS.15105.P.SS Stainless Steel Offset Single PaveSlot 105 105 200 10 50/100 C, D 7.7
OS.15150.P.SS Stainless Steel Offset Single PaveSlot 105 150 200 10 50/100 C, D 11
Offset Single PaveSlot
PaveSlot Specs
KE - 150PaveSlot
Polycon Surface Water Drainage | KE - 150 Technical Brochure11 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk
Article no. Designation Upstand Height (mm)
Overall Width (mm)
Slot Width (mm)
Length (cm)
Load Class
Weight (kg)
CS.1560.P.G Galvanised Centre Single PaveSlot 60 60 200 10 50/100 C, D 4.5
CS.15105.P.G Galvanised Centre Single PaveSlot 105 105 200 10 50/100 C, D 8
CS.15150.P.G Galvanised Centre Single PaveSlot 150 150 200 10 50/100 C, D 11.4
CS.1560.P.SS Stainless Steel Centre Single PaveSlot 60 60 200 10 50/100 C, D 4.6
CS.15105.P.SS Stainless Steel Centre Single PaveSlot 105 105 200 10 50/100 C, D 8.2
CS.15150.P.SS Stainless Steel Centre Single PaveSlot 150 150 200 10 50/100 C, D 11.7
See the tables below for specifications on our paveslot gratings
Centre Single PaveSlot
Article no. Designation Upstand Height (mm)
Overall Width (mm)
Slot Width (mm)
Length (cm)
Load Class
Weight (kg)
OT.1560.P.G Galvanised Offset Twin PaveSlot 60 60 200 2 x 8mm 50/100 C, D 8.6
OT.15105.P.G Galvanised Offset Twin PaveSlot 105 105 200 2 x 8mm 50/100 C, D 15.2
OT.15150.P.G Galvanised Offset Twin PaveSlot 150 150 200 2 x 8mm 50/100 C, D 21.7
OT.1560.P.SS Stainless Steel Offset Twin PaveSlot 60 60 200 2 x 8mm 50/100 C, D 8.8
OT.15105.P.SS Stainless Steel Offset Twin PaveSlot 105 105 200 2 x 8mm 50/100 C, D 15.4
OT.15150.P.SS Stainless Steel Offset Twin PaveSlot 150 150 200 2 x 8mm 50/100 C, D 21.9
Offset Twin PaveSlot
KE - 150PaveSlot
Polycon Surface Water Drainage | KE - 150 Technical Brochure12 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk
Article no. Designation Upstand Height (mm)
Overall Width (mm)
Slot Width (mm)
Length (cm)
Load Class
Weight (kg)
AT.1560.P.G Galvanised Offset Single Access Tray 60 60 200 10 50 C, D 4.1
AT.15105.P.G Galvanised Offset Single Access Tray 105 105 200 10 50 C, D 7.2
AT.15150.P.G Galvanised Offset Single Access Tray 150 150 200 10 50 C, D 10.2
AT.1560.P.SS Stainless Steel Offset Single Access Tray 60 60 200 10 50 C, D 4.3
AT.15105.P.SS Stainless Steel Offset Single Access Tray 105 105 200 10 50 C, D 7.4
AT.15150.P.SS Stainless Steel Offset Single Access Tray 150 150 200 10 50 C, D 10.4
See the tables below for specifications on our paveslot
Access Tray PaveSlot
Article no. Designation Upstand Height (mm)
Overall Width (mm)
Slot Width (mm)
Length (cm)
Load Class
Weight (kg)
CT.1560.P.G Galvanised Centre Twin PaveSlot 60 60 200 2 x 8mm 50/100 C, D 8.4
CT.15105.P.G Galvanised Centre Twin PaveSlot 105 105 200 2 x 8mm 50/100 C, D 14.8
CT.15150.P.G Galvanised Centre Twin PaveSlot 150 150 200 2 x 8mm 50/100 C, D 21.1
CT.1560.P.SS Stainless Steel Centre Twin PaveSlot 60 60 200 2 x 8mm 50/100 C, D 8.6
CT.15105.P.SS Stainless Steel Centre Twin PaveSlot 105 105 200 2 x 8mm 50/100 C, D 15
CT.15150.P.SS Stainless Steel Centre Twin PaveSlot 150 150 200 2 x 8mm 50/100 C, D 21.2
Centre Twin PaveSlot
Technical Data SheetKE - 150
Installation GuideGrounds condtions must be suitable and all dimensions shown are the minimum requirement. Engineering advice should be taken where necessary and any questions should be directed to Polycon’s technical team through emailing us at [email protected] or by calling us on 0151 424 9747
BlockPaving
1 2 3 4 5 6** Minimum Concrete Haunch
25 N/mm²
Concrete Sub Base EarthConcrete Haunch
Sand LayerExpansion
Joint
Detail AAllow for overbuild of 3mm to
5mm above the grating surfaces
Tarmac
Concrete PaveSlot
Z
YH2
Y
5 5
3
Z
Y
Y
H2
1 1
Z
Y
H2
Y
1
H2
Z
Y
Y
15 5
2
3
2
4
3
2
3
2
4
6
3
2
4
3
2
MORTOR
3
2
3
2
4
PAVING SLABBLOCK PAVE
Load Class A15 B125 C250 D400
H2 - Channel HeightChannel Height
Channel Height
Channel Height
Channel Height
Y - Minimum Surround 100mm 150mm 150mm 200mm
Z - Minimum Surround 100mm 150mm 150mm 200mm
T1 - Minimum Depth 40mm 40mm 40mm 40mm
T2 - Maximum Depth 95mm 55mm 55mm 55mm
Polycon Surface Water Drainage
Widnes Business Park, Foundry Lane, Widnes, WA8 8UB, England
Email: [email protected]: 0151 422 9747
Visit our website for our full range of products at www.polycon.co.uk