Katalog 2007 En

ERE⁄L‹ IRON AND STEEL WORKS CO.

2

www.erdemir.com.tr 3

• Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

• Reminder, Abbreviations and Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Steel Grades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Hot Rolled Flat Steel Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

• Grade Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20• Steel Grades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30• Available Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81• Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106• Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Cold Rolled Flat Steel Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

• Grade Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130• Steel Grades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132• Available Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149• Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156• Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

Galvanized/Galvannealed Flat Steel Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163


Electrolytic Tinplate (ETP) and Electrolytic Chromium Coated Steel (ECCS or TFS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199


• Labelling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221• By-Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222• Production Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226• Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230• Contact Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232

Co

nte

nts

4


Dear Customers,

For nearly half a century, we've been producing steel for you, and we offer you steel with its qualities of high durability power,high shapebility, functionality and flexibility and also with its quality to be formed into aesthetic tools as well. As being youngand dynamic within the centuries long story of steel and as being deep-rooted and confident institution within the story of ourRepublic, we continue our production by enhancing the quality and diversity of our products.

Along our travel from 1965 to the future, by taking the demand of our customers and the needs of our country intoconsideration, we've been continuing our investments in parallel with our lasting development principle in all areas such ascapacity, technology, human resources and quality. The modernization and transformation investment realized in ‹sdemir hasbeen a significant step by ERDEM‹R Group toward the elimination of imbalance against the flat steel production in ourcountry.

Erdemir Group is acquired by OYAK, Turkey's leading institutional investor, on February 27, 2006. Subsequently ERDEM‹Raligned itself with OYAK's mission, vision and values to reflect the management philosophy and business approach of OYAK,and initiated an extensive restructuring process within which a commitment to reliable and enduring partnership is a keystone.

At the present, there are 305 ERDEM‹R steel grades on the market. Our customers' requirements, and continuouscooperation played a vital role in the development of our 82 steel grades with national/international TS 3813 EN 10130, TS2162 EN 10025, TS EN 10202, Lloyd's Register (LR), American Bureau of Shipping (ABS), Community Europe (CE)certificates, and 268 grades meeting or corresponding to national/international standards.

Development of common strategies with the sectors for which we provide services has gradually become more important inthe current market where there is an intense competition and where the capital is highly floating as a result of theglobalization. We believe that ensuring the flow of information among sectors, sharing the future projects and establishment ofcommon working platforms toward realization of these projects would enhance and strengthen our collaborations.

We attribute great importance to ensure our responsibilities for not only our customers but also for all our stakeholders, andwe take into consideration that our relations with our workers and also suppliers are the factors influencing directly over ourquality. We treat the environmental management in all stages of production as our prior responsibility to next generations.

In order to provide better services for our customers and to establish the comformity of processes with the users, we ensurethat our team and all our relevant units within the Customer Tech Services Process are ready to answer your questions andmeet your needs.

I wish the continuation of our collaboration by getting stronger and I'm pleased to introduce the attached catalogue.

Respectfully yours,

Intr

od

uct

ion

O¤uz ÖZGENChief Executive Officer and Board Member

6

Intr

od

uct

ion

ERDEM‹R PRODUCT CATALOGUE 2007

www.erdemir.com.tr

Rem

ind

er, A

bb

revi

atio

ns

and

Sym

bo

ls

7

Reminder, Abbreviations and Symbols

• Values of chemical properties of steel grades marked as “Erdemir” are for purposes of information only.

• The thickness values always represent the nominal thicknesses, unless specified otherwise.The nominal thickness is equivalent to the middle of the customer's tolerance range.

• If further assistance is required about our products or services or there is a need of additional information, please contact our “Sales & Marketing Department.”

REMARKS

Symbols Used For Mechanical TestsSymbol ExplanationRe Yield strengthRm Tensile strengthRp0,2 Proof strength at elevated temperatureBH2 Increase in proof strength after heatingA Elongation (%)A5 Elongation (Lo=5.65 x √So)A50 Elongation (Lo=50 mm)A80 Elongation (Lo=80 mm)A100 Elongation (Lo=100 mm)A200 Elongation (Lo=200 mm)So Cross-sectional area of the specimen (mm2)Lo Original gauge length of the specimend Nominal thickness (mm)t Tonner Plastic stain ration Strain hardening exponentRa Surface roughness (µm)Impact Impact testKVc Impact energy (J)Temp Test temperature (°C)Bend Bend testmrb Mandrel radius for bendingmdb Mandrel diameter for bendingtrans. Transverse test piecelong. Longitudinal test pieceHRB Hardness of Rockwell “B”min. Minimummax. Maximum= Equal to< Smaller than≤ Smaller than or equal to> Larger than≥ Larger than or equal to

Symbols Used For ChemicalElementsSembol ElementC CarbonMn ManganeseP PhosphorusS Sulfur Si Silicon Al Aluminum Cu CopperN NitrogenO OxygenH HydrogenCa CalciumTi TitaniumV VanadiumCr ChromiumNi NickelMo MolybdenumNb Niobium B BoronSn TinFe IronZn ZincPb LeadAs ArsenicW Wolfram (Tungsten)

Intr

od

uct

ion

8

Intr

od

uct

ion


www.erdemir.com.tr

Ste

el G

rad

es

9

Steel Grades

Erdemir CorrespondingSteel Grade Product Group Standard Grade Page Number120 Cold SPC270C-Erdemir TY01 120 134121 Cold SPC270C-Erdemir TY02 121 134130 Cold XES-Erdemir RN01 130 137131 Cold SPC270D-Erdemir TY03 131 137132 Cold SPC270D-Erdemir TY04 132 137250 Cold XE-320 DR-Erdemir RN02 250 143251 Cold F1 Gr. 300-Erdemir FR01 251 143260 Cold XE-360 DR-Erdemir RN03 260 143311 Galvanized A2 DC05-Erdemir FR02 311 170312 Galvanized XE-Erdemir RN04 312 170323 Galvanized A3 DC06-Erdemir FR03 323 170324 Galvanized XES-Erdemir RN05 324 170355 Galvanized F1 Gr. 250-Erdemir FR04 355 175366 Galvanized XE-320 D-Erdemir RN06 366 175367 Galvanized F1 Gr. 300-Erdemir FR05 367 175372 Galvanized XE-360 D-Erdemir RN07 372 175410 Galvannealed SCGA 270C-Erdemir TY05 410 172411 Galvannealed SCGA 270C-Erdemir TY06 411 172430 Galvannealed SCGA 270D-Erdemir TY07 430 172431 Galvannealed SCGA 270D-Erdemir TY08 431 172482 Galvannealed SCGA 340BH-Erdemir TY09 482 182700 Hot HES-HC-Erdemir RN08 700 36720 Hot StW24H-Erdemir MB01 720 42735 Hot B105-10-2000-Erdemir EE01 735 52800 Hot HE-320 DR-Erdemir RN09 800 56801 Hot A3 Gr. 300-Erdemir FR06 801 56810 Hot HE-360 DR-Erdemir RN10 810 56811 Hot E1 Gr.350-Erdemir FR07 811 56812 Hot A4 Gr. 350-Erdemir FR08 812 56820 Hot E1 Gr.400-Erdemir FR09 820 56835 Hot DIN EN 10149 - P2 - 95 S500MC Special 561110 Cold Erdemir - 01 1110 1461118 Galvanized DIN EN 10292 - 05 HC180BD + Z 1771122 Galvanized DIN EN 10292 - 05 HC220BD + Z 1771124 Galvanized A7-Erdemir FR10 1124 1801126 Galvanized DIN EN 10292 - 05 HC260BD + Z 1771130 Galvanized DIN EN 10292 - 05 HC300BD + Z 1771218 Galvannealed DIN EN 10292 - 05 HC180BD + ZF 1811222 Galvannealed DIN EN 10292 - 05 HC220BD + ZF 1811226 Galvannealed DIN EN 10292 - 05 HC260BD + ZF 1811230 Galvannealed DIN EN 10292 - 05 HC300BD + ZF 1811311 Galvanized DIN EN 10327 - 04 DX51D + Z 1681312 Galvanized DIN EN 10327 - 04 DX52D + Z 1681313 Galvanized DIN EN 10327 - 04 DX53D + Z 168

Intr

od

uct

ion

10

Erdemir CorrespondingSteel Grade Product Group Standard Grade Page Number1314 Galvanized DIN EN 10327 - 04 DX54D + Z 1681315 Galvanized DIN EN 10327 - 04 DX56D + Z 1681322 Galvanized DIN EN 10326 - 04 S220GD + Z 1731325 Galvanized DIN EN 10326 - 04 S250GD + Z 1731328 Galvanized DIN EN 10326 - 04 S280GD + Z 1731332 Galvanized DIN EN 10326 - 04 S320GD + Z 1731335 Galvanized DIN EN 10326 - 04 S350GD + Z 1731411 Galvannealed DIN EN 10327 - 04 DX51D + ZF 1711412 Galvannealed DIN EN 10327 - 04 DX52D + ZF 1711413 Galvannealed DIN EN 10327 - 04 DX53D + ZF 1711414 Galvannealed DIN EN 10327 - 04 DX54D + ZF 1711415 Galvannealed DIN EN 10327 - 04 DX56D + ZF 1711422 Galvannealed DIN EN 10326 - 04 S220GD + ZF 1761425 Galvannealed DIN EN 10326 - 04 S250GD + ZF 1761428 Galvannealed DIN EN 10326 - 04 S280GD + ZF 1761432 Galvannealed DIN EN 10326 - 04 S320GD + ZF 1761435 Galvannealed DIN EN 10326 - 04 S350GD + ZF 1761522 Galvanized DIN EN 10292 - 05 HC220PD + Z 1831660 Galvanized Erdemir - 06 1660 1851718 Hot Erdemir - 04 1718 321722 Hot Erdemir - 04 1722 321726 Hot Erdemir - 04 1726 321822 Hot Erdemir - 04 1822 321825 Hot Erdemir - 04 1825 321828 Hot Erdemir - 04 1828 321832 Hot Erdemir - 04 1832 321835 Hot Erdemir - 04 1835 322004 Tinplate DIN EN 10202 - 01 TS245 2042005 Tinplate DIN EN 10202 - 01 TS275 2042006 Tinplate DIN EN 10202 - 01 TS415 2042008 Hot Erdemir - 01 2008 372009 Hot ASTM A53 - 06 A 372023 Tinplate DIN EN 10202 - 01 TS230 2042026 Tinplate DIN EN 10202 - 01 TS260 2042104 Tin Free Steel DIN EN 10202 - 01 TS245 2052105 Tin Free Steel DIN EN 10202 - 01 TS275 2052106 Tin Free Steel DIN EN 10202 - 01 TS415 2052123 Tin Free Steel DIN EN 10202 - 01 TS230 2052126 Tin Free Steel DIN EN 10202 - 01 TS260 2052223 Tinplate DIN EN 10202 - 01 TH230 2062225 Tinplate DIN EN 10202 - 01 TH245 2062226 Tinplate DIN EN 10202 - 01 TH260 2062228 Tinplate DIN EN 10202 - 01 TH275 2062242 Tinplate DIN EN 10202 - 01 TH415 206

Intr

od

uct

ion


www.erdemir.com.tr

Ste

el G

rad

es

11

Erdemir CorrespondingSteel Grade Product Group Standard Grade Page Number2244 Tin Plate DIN EN 10202 - 01 TH435 2062252 Tin Plate, DR DIN EN 10202 - 01 TH520 2082255 Tin Plate, DR DIN EN 10202 - 01 TH550 2082258 Tin Plate, DR DIN EN 10202 - 01 TH580 2082262 Tin Plate, DR DIN EN 10202 - 01 TH620 2082323 Tin Free Steel DIN EN 10202 - 01 TH230 2072325 Tin Free Steel DIN EN 10202 - 01 TH245 2072326 Tin Free Steel DIN EN 10202 - 01 TH260 2072328 Tin Free Steel DIN EN 10202 - 01 TH275 2072342 Tin Free Steel DIN EN 10202 - 01 TH415 2072344 Tin Free Steel DIN EN 10202 - 01 TH435 2073008 Hot SAE J403 - 01 1008 783010 Hot SAE J403 - 01 1010 783012 Hot SAE J403 - 01 1012 783015 Hot SAE J403 - 01 1015 783018 Hot ASTM A283 - 03 C 383020 Hot SAE J403 - 01 1020 783030 Hot SAE J403 - 01 1030 783237 Hot DIN EN 10025 - P2 - 04 S235 JR 413241 Hot ASTM A36 - 05 A36 393244 Hot DIN EN 10025 - P2 - 04 S275 JR 403250 Hot DIN EN 10025 - P2 - 04 E295 483252 Hot DIN EN 10025-P2-04 S355JR 40 3260 Hot DIN EN 10025 - P2 - 04 E335 483281 Hot DIN EN 10025 - P2 - 04 S235 JR (Cu) 413330 Hot ASTM A1011 - 05 SS 30 443333 Hot ASTM A1011 - 05 SS33 443336 Hot ASTM A1011 - 05 SS36 Type1 443337 Hot DIN EN 10025 - P2 - 04 S235 JR 403340 Hot ASTM A1011 - 05 SS 40 443345 Hot ASTM A1011 - 05 SS 45 443350 Hot ASTM A1011 - 05 SS 50 443430 Hot ASTM A1018 - 06b SS 30 453433 Hot ASTM A1018 - 06b SS 33 453436 Hot ASTM A1018 - 06b SS36 Type1 453440 Hot ASTM A1018 - 06b SS 40 453660 Hot DP600-Erdemir HL01 3660 643701 Hot ABS - P2 - 05 A 653702 Hot ABS - P2 - 05 B 653732 Hot ABS - P2 - 05 AH32 663736 Hot ABS - P2 - 05 AH36 673922 Hot DIN EN 10111 - 98 DD 11 573923 Hot DIN EN 10111 - 98 DD 12 573936 Hot Erdemir - 01 3936 58

Intr

od

uct

ion

12

Erdemir Corresponding Steel Grade Product Group Standard Grade Page Number3937 Hot DIN EN 10025 - P2 - 04 S235 JRC 593938 Hot DIN EN 10025 - P2 - 04 S275 J2 +N 593940 Hot 1937-02-Erdemir HL02 3940 603944 Hot DIN EN 10025 - P2 - 04 S275 JRC 593945 Hot Erdemir - 01 3945 583946 Hot 1937-03-Erdemir HL03 3946 613949 Hot Erdemir - 03 3949 583955 Hot DIN EN 10149 - P2 - 95 S355 MC 623957 Hot DIN EN 10149 - P2 - 95 S420 MC 623960 Hot 6000-2-Erdemir HL04 3960 633995 Hot Erdemir - 01 3995 804009 Hot ASTM A53 - 06 A 374044 Hot DIN EN 10025 - P2 - 04 S275 JRC 464137 Cold DIN 1623 - P2 - 86 St 37-3 G 1454237 Hot DIN EN 10025 - P2 - 04 S235 JR 414244 Hot DIN EN 10025 - P2 - 04 S275 JR 414437 Hot Erdemir - 01 4437 314732 Hot ABS - P2 - 05 DH32 664736 Hot ABS - P2 - 05 DH36 674932 Hot DIN EN 10149 - P2 - 95 S315 MC 554936 Hot DIN EN 10149 - P2 - 95 S355 MC 554942 Hot DIN EN 10149 - P2 - 95 S420 MC 554946 Hot DIN EN 10149 - P2 - 95 S460 MC 554950 Hot DIN EN 10149 - P2 - 95 S500 MC 555035 Hot SAE J403 - 01 1035 785040 Hot SAE J403 - 01 1040 785045 Hot SAE J403 - 01 1045 785050 Hot SAE J403 - 01 1050 785060 Hot SAE J403 - 01 1060 785070 Hot SAE J403 - 01 1070 785080 Hot SAE J403 - 01 1080 785105 Cold Erdemir - 05 5105 1445130 Cold SAE J403 - 01 1030 1465140 Cold SAE J403 - 01 1040 1465145 Cold SAE J403 - 01 1045 1465155 Cold Erdemir - 01 5155 1485246 Hot ASTM A709 - 06 345F Type2 545270 Hot DIN EN 10025 - P2 - 04 E360 485345 Hot ASTM A829 - 04 1345 795360 Hot ASTM A829 - 04 5160 795437 Hot Erdemir - 01 5437 315512 Hot Erdemir - 02 5512 335513 Hot Erdemir - 05 5513 335515 Hot Erdemir - 04 5515 33

Intr

od

uct

ion


www.erdemir.com.tr

Ste

el G

rad

es

13

Erdemir Corresponding Steel Grade Product Group Standard Grade Page Number5620 Hot DIN EN 10083 - P3 - 96 20MnB5 795630 Hot DIN EN 10083 - P3 - 96 30MnB5 795732 Hot ABS - P2 - 05 EH32 665736 Hot ABS - P2 - 05 EH36 676006 Hot SAE J403 - 01 1006 786018 Hot SAE J403 - 01 1018 786035 Hot ASTM A1011 - 05 SS36 Type2 446036 Hot ASTM A1018 - 06b SS36 Type2 456037 Hot DIN EN 10025 - P2 - 04 S235 J2C +N 476040 Hot ASTM A500 - 03a B 376044 Hot DIN EN 10025 - P2 - 04 S275 J2C +N 476050 Hot JIS G 3106 - 04 SM 490 A 436052 Hot DIN EN 10025 - P2 - 04 S355 J2C +N 476106 Cold SAE J403 - 01 1006 1466108 Cold SAE J403 - 01 1008 1466109 Cold Erdemir - 01 6109 1446110 Cold SAE J403 - 01 1010 1466112 Cold DIN EN 10130 - 99 DC O1 1326113 Cold DIN EN 10130 - 99 DC O3 1326114 Cold DIN EN 10130 - 99 DC O4 1326137 Cold DIN 1623 - P2 - 86 St 37-3 G 1456182 Cold DIN EN 10130 - 99 DC O1 ( Cu ) 1336222 Hot DIN EN 10111 - 98 DD 11 356223 Hot DIN EN 10111 - 98 DD 12 356224 Hot DIN EN 10111 - 98 DD 13 356237 Hot DIN EN 10025 - P2 - 04 S235 J2 +N 416244 Hot DIN EN 10025 - P2 - 04 S275 J2 +N 416252 Hot DIN EN 10025 - P2 - 04 S355 J2 +N 416282 Hot DIN EN 10111 - 98 DD 11 ( Cu ) 356284 Hot DIN EN 10025 - P2 - 04 S355 J2 +N ( Cu ) 406314 Hot Erdemir - 04 6314 306315 Hot Erdemir - 04 6315 306335 Hot DIN EN 10028 - P2 - 03 P235 GH 726341 Hot DIN EN 10028 - P2 - 03 P265 GH 726345 Hot DIN EN 10028 - P2 - 03 16Mo3 736347 Hot DIN EN 10028 - P2 - 03 P295 GH 726352 Hot DIN EN 10028 - P2 - 03 P355 GH 726353 Hot DIN EN 10028 - P3 - 03 P355 NH 716355 Hot DIN EN 10028 - P3 - 03 P355 NL2 716406 Hot SAE J403 - 01 1006 316408 Hot SAE J403 - 01 1008 316412 Hot Erdemir - 04 6412 306413 Hot Erdemir - 04 6413 306422 Hot DIN 1614 - P1 - 86 St 22 31

Intr

od

uct

ion

14

Erdemir Corresponding Steel Grade Product Group Standard Grade Page Number6423 Hot DIN 1614 - P1 - 86 RRSt 23 316424 Hot DIN 1614 - P1 - 86 St 24 316426 Hot Erdemir - 02 6426 316513 Cold DIN EN 10209 - 96 DC 04 EK 1426523 Hot Erdemir - 01 6523 336612 Cold DIN EN 10130 - 99 DC O1 1376624 Hot DIN EN 10111 - 98 DD 13 ( B ) 356704 Hot ABS - P2 - 05 D 656705 Hot ABS - P2 - 05 E 656732 Hot ABS - P2 - 05 FH32 666736 Hot ABS - P2 - 05 FH36 676741 Hot JIS G 3101 - 04 SS 400 436837 Hot DIN EN 10120 - 97 P245 NB 686838 Hot ASTM A285 - 03 C 696842 Hot DIN EN 10120 - 97 P265 NB 686847 Hot DIN EN 10120 - 97 P310 NB 686850 Hot LR - P2 - 00 490 FG 696852 Hot DIN EN 10120 - 97 P355 NB 686855 Hot ASTM A516 - 06 55 706860 Hot ASTM A516 - 06 60 706865 Hot ASTM A516 - 06 65 706870 Hot ASTM A516 - 06 70 707022 Cold Erdemir - 06 7022 1407111 Cold DIN EN 10130 - 99 DC O1 1397114 Cold DIN EN 10130 - 99 DC O4 1357115 Cold DIN EN 10130 - 99 DC O5 1357116 Cold DIN EN 10130 - 99 DC O6 1357122 Cold DIN EN 10130 - 99 DC O1 1357123 Cold DIN EN 10130 - 99 DC O3 1357124 Cold DIN EN 10130 - 99 DC O4 1367125 Cold DIN EN 10268 - 99 H240 LA 1427128 Cold DIN EN 10268 - 99 H280 LA 1427132 Cold DIN EN 10268 - 99 H320 LA 1427136 Cold DIN EN 10268 - 99 H360 LA 1427140 Cold DIN EN 10268 - 99 H400 LA 1427222 Hot DIN EN 10111 - 98 DD 11 357224 Hot DIN EN 10111 - 98 DD 14 357314 Cold DIN EN 10130 - 99 DC O4 1367315 Cold DIN EN 10130 - 99 DC O5 1367316 Cold DIN EN 10130 - 99 DC O6 1367414 Hot Erdemir - 04 7414 307416 Hot Erdemir - 04 7416 307512 Cold DIN EN 10209 - 96 DC 01 EK 1387513 Cold DIN EN 10209 - 96 DC 04 EK 138

Erdemir Corresponding Steel Grade Product Group Standard Grade Page Number7514 Cold DIN EN 10209 - 96 DC 06 ED 1387524 Hot Erdemir - 01 7524 337608 Cold SAE J403 - 01 1008 (B) 1467612 Cold DIN EN 10130 - 99 DC O1 1327660 Cold FE 600 DP F-Erdemir FT01 7660 1417726 Cold Erdemir - 06 7726 1398412 Hot DIN EN 10083 - P1 - 96 51 CrV 4 808414 Hot DIN EN 10269 - 99 21 CrMoV 57 808416 Hot Erdemir - 04 8416 798430 Hot DIN 30 CrMo 52 Special 808434 Hot DIN EN 10083 - P1 - 96 34 CrMo 4 808440 Hot DIN EN 10083 - P1 - 96 C45E Special 808613 Hot Erdemir - 03 8613 799030 Hot API 5L - 04 A PSL1 759035 Hot API 5L - 04 B PSL2 759042 Hot API 5L - 04 X42 PSL2 759046 Hot API 5L - 04 X46 PSL2 759052 Hot API 5L - 04 X52 PSL2 759056 Hot API 5L - 04 X56 PSL2 759060 Hot API 5L - 04 X60 PSL2 759065 Hot API 5L - 04 X65 PSL2 759070 Hot API 5L - 04 X70 PSL2 759160 Cold JIS G 3125 - 04 SPA - C 1479240 Hot API 5CT - 05 H40 769255 Hot API 5CT - 05 J55 769256 Hot API 5CT - 05 J55 Special 769257 Hot API 5CT - 05 K55 Special 769280 Hot API 5CT - 05 N80 Type1 769329 Hot ASTM A572 - 06 42 Type2 499335 Hot ASTM A572 - 06 50 Type2 499338 Hot ASTM A572 - 06 55 Type2 499342 Hot ASTM A572 - 06 60 Type3 499355 Hot DIN EN 10025 - P3 - 05 S355 N 499356 Hot DIN EN 10025 - P3 - 05 S355 NL 509435 Hot ASTM A656 - 05 50 Type3 519442 Hot ASTM A656 - 05 60 Type8 519449 Hot ASTM A656 - 05 70 Type8 519455 Hot ASTM A656 - 05 80 Type8 519460 Hot DIN EN 10025 - P3 - 05 S460 N 509500 Hot Erdemir - 05 9500 779960 Hot JIS G 3125 - 04 SPA - H 53

Intr

od

uct

ion


www.erdemir.com.tr

Ste

el G

rad

es

15

16

01www.erdemir.com.tr 17


Hot Rolled Flat Steel Products20 > Grade Index 30 > Steel Grades 81 > Available Sizes106 > Tolerances121 > Packaging

Ho

t R

olle

d P

rod

uct

s

18

Ho

t R

olle

d P

rod

uct

s

0319


www.erdemir.com.tr

Hot Rolled Flat Steel Products

We spread out our hot rolled steelgrades application areas in a widerange to meet the demands ofdifferent requests and expectations ofour customers who are active inindustrial area.

The steel grades for cold formingand deep drawing have excellentperformance in applications ofbending and drawing, so mainlyused in automotive industry andrelated sectors.

Wheel and frame steels which have both high strength and highformability properties are used forproducing wheels and frames inautomotive industry.

With the guaranteed minimum yieldand tensile strengths, satisfactoryductility and toughness properties,

General Application Areas

suitable for conventional weldingprocesses general structural steels are mainly used in buildingmachines, caterpillars, heavy platesfor general construction, land andrailway vehicles, storage tanks andcontainers production.

Hot rolled pipe grades, with high tensile strength, excellenttoughness and weldabilityproperties mainly used for theproduction of pipes for the transport of gaseous or fluidsubstances such as water or oil.

Steels for pressure vessels andboilers, with excellent forming andweldability properties, mainly used to manufacture boilers, drums,industrial thermal vessels, heatexchangers and pipes which areexposed to pressure and steam.

Deep drawing and non-ageing steels with excellent weldability and toughness properties formanufacturing of gas containers that guarantees the safetyrequirements.

Steels for shipbuilding with the weldability and requiredtoughness properties can be used for shipbuilding applications(the interior of the ship and the hull).

Rectangular shaped slabs which are solidified by continuous casting processand hot rolled into 1.50-20.00 mm thickness range. These hot rolled productscan be in the form of coils or cut into various lengths. Furthermore by hotrolling slabs into 5.00-200.00 mm thickness range and 1000-3800 mm widthrange plates are produced.

Ho

t R

olle

d P

rod

uct

s

20

Grade Index

Application Areas and Brand Correspondence of Hot Rolled Products

General CharacteristicsCorresponding

Erdemir and Major Applications Steel Standard Grade

Grade6406 SAE J403-01 10066408 SAE J403-01 1008

Low-carbon unalloyed mild steels for cold reducing6422 DIN 1614-P1-86 St 226423 DIN 1614-P1-86 RRSt 236424 DIN 1614-P1-86 St 246426 Erdemir-02 6426

Hot rolled steels for cold reducing and 6412 Erdemir-04 6412

galvanizing by hot-dip process 6413 Erdemir-04 64136314 Erdemir-04 63146315 Erdemir-04 6315

Hot rolled steels for cold reducing and 7414 Erdemir-04 7414continuous annealing 7416 Erdemir-04 7416Hot rolled steels for cold reducing and 1718 Erdemir-04 1718manufacturing galvanized products of 1722 Erdemir-04 1722bake-hardening steels by hot-dip process 1726 Erdemir-04 1726

1822 Erdemir-04 1822Hot rolled steels for cold reducing and 1825 Erdemir-04 1825manufacturing galvanized products of 1828 Erdemir-04 1828structural steels by hot-dip process 1832 Erdemir-04 1832

1835 Erdemir-04 1835Medium carbon steels 4437 Erdemir-01 4437for cold reducing 5437 Erdemir-01 5437

Hot rolled steel for cold reduc›ng for 5512 Erdemir-02 5512

making electrical steel 5513 Erdemir-05 55135515 Erdemir-04 55156222 DIN EN 10111-98 DD 116223 DIN EN 10111-98 DD 12Low-carbon drawing quality steels for 6224 DIN EN 10111-98 DD 13immediate cold forming 6624 DIN EN 10111-98 DD 13 (B)700 HES-HC-Erdemir RN08 700

Non-aging extra deep-drawing quality steel 7222 DIN EN 10111-98 DD 117224 DIN EN 10111-98 DD 14

Low-carbon steels for porcelain enamelling 6523 Erdemir-01 6523 7524 Erdemir-01 75246006 SAE J403-01 1006

Low and medium carbon steels of commercial 3008 SAE J403-01 1008quality for general uses 3010 SAE J403-01 1010

3012 SAE J403-01 10123015 SAE J403-01 10152008 Erdemir-01 2008

Unalloyed carbon steels with intermediate- 2009 ASTM A 53-06 Astrength for pipes and tubes 4009 ASTM A 53-06 A

6040 ASTM A 500-03a B

Ho

t R

olle

d P

rod

uct

s

05

Gra

de

Ind

ex

21


www.erdemir.com.tr

Corresponding Similar Standards (1)

Material Number Previous EN USA JIS Page Number

31313131313130303030303032323232323232323131333333

1.0332 DIN 1614-P2 StW22 ASTM A1011 CS Type B JIS G3131 SPHC 341.0398 DIN 1614-P2 RRStW23 ASTM A1011 DS Type A JIS G3131 SPHD 341.0335 DIN 1614-P2 StW24 ASTM A1011 DS Type B JIS G3131 SPHD 341.0335 DIN 1614-P2 StW24 JIS G3131 SPHD 34

JIS G3131 SPHC 361.0332 DIN 1614-P2 StW22 JIS G3131 SPHC 341.0389 JIS G3131 SPHE 34

3333

ASTM A1011 CS Type A 78ASTM A1011 CS Type D 78

78787837373737

Ho

t R

olle

d P

rod

uct

s

22

General Characteristics Erdemir Corresponding

and Major Applications SteelGrade Standard Grade

4932 DIN EN 10149-P2-95 S315 MC4936 DIN EN 10149-P2-95 S355 MC4942 DIN EN 10149-P2-95 S420 MC4946 DIN EN 10149-P2-95 S460 MC

High-strength steels with improved formability for 4950 DIN EN 10149-P2-95 S500 MCautomobile structural uses 800 HE-320DR-Erdemir RN09 800

801 A3 Gr. 300-Erdemir FR06 801810 HE-360DR-Erdemir RN10 810811 E1 Gr. 350-Erdemir FR07 811812 A4 Gr. 350-Erdemir FR08 812820 E1 Gr. 400-Erdemir FR09 820835 DIN EN 10149-P2-95 S500 MC Special

9435 ASTM A656 50 Type 3High-strength low-alloy steel 9442 ASTM A656 60 Type 8with improved formability 9449 ASTM A656 70 Type 8

9455 ASTM A656 80 Type 86837 DIN EN 10120-97 P245 NB

Steels for LPG (liquefied petroleum gas) cylinders 6842 DIN EN 10120-97 P265 NB6847 DIN EN 10120-97 P310 NB6852 DIN EN 10120-97 P355 NB6855 ASTM A516-06 55

Hot rolled carbon steels with moderate and lower 6860 ASTM A516-06 60temperature properties for pressure purposes 6865 ASTM A516-06 65

6870 ASTM A516-06 706335 DIN EN 10028-P2-03 P235 GH6341 DIN EN 10028-P2-03 P265 GHUnalloyed steels with elevated temperature properties6345 DIN EN 10028-P2-03 16Mo3for pressure purposes (boilers, steam boiler plants, 6347 DIN EN 10028-P2-03 P295 GHpressure vessels, etc.)6352 DIN EN 10028-P2-03 P355 GH

Fine grain steels in normalized condition for 6353 DIN EN 10028-P3-03 P355 NHpressure purposes 6355 DIN EN 10028-P3-03 P355 NL2

3701 ABS-P2-05 AHull structural steels with ordinary-strength for 3702 ABS-P2-05 B

6704 ABS-P2-05 Dshipbuilding6705 ABS-P2-05 E3732 ABS-P2-05 AH323736 ABS-P2-05 AH36

Hull structural steels with high-strength for 4732 ABS-P2-05 DH32

shipbuilding4736 ABS-P2-05 DH365732 ABS-P2-05 EH325736 ABS-P2-05 EH366732 ABS-P2-05 FH326736 ABS-P2-05 FH36

Ho

t R

olle

d P

rod

uct

s



Corresponding Similar Standards(1)

Material Number Previous EN USA JIS PageNumber

1.0972 ASTM A1011 HSLAS Gr.45 Class 2 551.0976 ASTM A1011 HSLAS Gr.50 Class 2 551.0980 ASTM A1011 HSLAS Gr.60 Class 2 551.0982 ASTM A1011 HSLAS Gr.65 Class 2 551.0984 ASTM A1011 HSLAS Gr.70 Class 2 55

5656565656565651515151

1.0111 JIS G3116 SG255 681.0423 JIS G3116 SG295 681.0437 JIS G3116 SG325 681.0557 JIS G3116 SG365 68

70707070

1.0345 DIN 17155 H I 721.0425 DIN 17155 H II 721.5415 731.0481 DIN 17155 17Mn4 721.0473 DIN 17155 19Mn6 721.0565 DIN 17102 WStE355 711.1106 DIN 17102 EStE355 71

ASTM A131 Gr.A 65ASTM A131 Gr.B 65ASTM A131 Gr.D 65ASTM A131 Gr.E 65

6667666766676667

Gra

de

Ind

ex

Ho

t R

olle

d P

rod

uct

s

24

General Characteristics Erdemir CorrespondingAnd Major Applications Steel

Grade Standard Grade

High-strength carbon and carbon-manganese 735 B105-10-2000-Erdemir EE01 735

steels for machine parts and general construction 3252 DIN EN 10025-P2-04 S355 JR

6252 DIN EN 10025-P2-04 S355 J2 +N3250 DIN EN 10025-P2-04 E295

High-strength unalloyed high-carbon steels 3260 DIN EN 10025-P2-04 E3355270 DIN EN 10025-P2-04 E360720 St W24H-Erdemir MB01 720

3237 DIN EN 10025-P2-04 S235 JR3241 ASTM A 36-05 A363337 DIN EN 10025-P2-04 S235 JR4237 DIN EN 10025-P2-04 S235 JR6237 DIN EN 10025-P2-04 S235 J2 +N3244 DIN EN 10025-P2-04 S275 JR4244 DIN EN 10025-P2-04 S275 JR

Non-alloy carbon steels of structural 6244 DIN EN 10025-P2-04 S275 J2 +Nquality for general purposes 3018 ASTM A 283-03 C

6018 SAE J403-01 10183020 SAE J403-01 10203030 SAE J403-01 10305035 SAE J403-01 10355040 SAE J403-01 10405045 SAE J403-01 10456741 JIS G 3101-04 SS 4003660 DP600-Erdemir HL01 36603922 DIN EN 10111-98 DD 113923 DIN EN 10111-98 DD 123936 Erdemir-01 39363937 DIN EN 10025-P2-04 S235 JRC3938 DIN EN 10025-P2-04 S275 J2 +N3940 1937-02-Erdemir HL02 3940

Steels for wheel production 3944 DIN EN 10025-P2-04 S275 JRC3945 Erdemir-01 39453946 1937-03-Erdemir HL03 39463949 Erdemir-03 39493955 DIN EN 10149-P2-95 S355 MC3957 DIN EN 10149-P2-95 S420 MC3960 6000-2-Erdemir HL04 3960

Structural steel for bridges 5246 ASTM A 709-06 345F Type29329 ASTM A572 42 Type2

Hot rolled weldable fine grain structural steels 9335 ASTM A572 50 Type29338 ASTM A572 55 Type29342 ASTM A572 60 Type3

Hot rolled weldable fine grain structural 9355 DIN EN 10025-P3-05 S355 N

steels in the normalized condition 9356 DIN EN 10025-P3-05 S355 NL9460 DIN EN 10025-P3-05 S460 N

Hot rolled steel with high strength for safety case 9500 Erdemir-05 9500

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Gra

de

Ind

ex

25



PageMaterial Number Previous EN USA JIS Number

521.0045 DIN 17100 St52-3 ASTM A1011 SS Gr.50 40

1.0570 DIN 17100 St52-3 ASTM A1011 SS Gr.50 401.0050 DIN 17100 St50-2 481.0060 DIN 17100 St60-2 481.0070 DIN 17100 St70-2 48

421.0038 DIN 17100 St37-2 ASTM A1011 SS Gr.36 Type1 40

391.0038 DIN 17100 St37-2 401.0038 DIN 17100 St37-2 ASTM A1011 SS Gr.33 401.0117 DIN 17100 St37-3 401.0044 DIN 17100 St44-2 ASTM A1011 SS Gr.40 401.0044 DIN 17100 St44-2 ASTM A1011 SS Gr.40 401.0145 DIN 17100 St44-3 40

38787878787878

ASTM A36 4364

1.0332 DIN 1614-P2 StW22 JIS G3131 SPHC 571.0398 DIN 1614-P2 RRStW23 JIS G3131 SPHD 57

581.0122 DIN 17100 St37-2 591.0144 DIN 17100 St37-3 59

601.0128 DIN 17100 St44-2 59

58JIS G3113 SAPH 440 61

581.0976 621.0980 62

63ASTM A572 Gr.50 Type 2 54

49ASTM A709 Gr.345F Type 2 49

4949

1.0545 DIN EN 10113-2 S355N ASTM A1011 HSLAS Gr.50 Class 1 501.0546 DIN EN 10113-2 S355NL ASTM A1011 HSLAS Gr.50 Class 1 501.8901 DIN EN 10113-2 S460N ASTM A1011 HSLAS Gr.65 Class 1 50

77

Ho

t R

olle

d P

rod

uct

s

26

General Characteristics Erdemir Corresponding

And Major Applications SteelGrade Standard Grade

4044 DIN EN 10025-P2-04 S275 JRC3330 ASTM A 1011-05 SS 303333 ASTM A 1011-05 SS 333336 ASTM A 1011-05 SS 36 Type16035 ASTM A 1011-05 SS 36 Type23340 ASTM A 1011-05 SS 403345 ASTM A 1011-05 SS 45

Steels with improved formability for 3350 ASTM A 1011-05 SS 50general structural uses 3430 ASTM A 1018-06b SS 30

3433 ASTM A 1018-06b SS 333436 ASTM A 1018-06b SS 36 Type16036 ASTM A 1018-06b SS 36 Type23440 ASTM A 1018-06b SS 406037 DIN EN 10025-P2-04 S235 J2C +N6044 DIN EN 10025-P2-04 S275 J2C +N6050 JIS G 3106-04 SM 490 A6052 DIN EN 10025-P2-04 S355 J2C +N

Carbon steel with intermediate-strength for pressure vessels 6838 ASTM A 285-03 CSteel for pipes used in building of dams 6850 LR-P2-00 490 FG‹ntermediate-strength carbon steel for casted slab 3995 Erdemir-01 3995

3281 DIN EN 10025-P2-04 S235 JR (Cu)Atmospheric corrosion resisting steels 6282 DIN EN 10111-98 DD 11 (Cu)of structural quality 6284 DIN EN 10025-P2-04 S355 J2 (Cu) +N

9960 JIS G 3125-04 SPA - H

Alloy structural steel plates5345 ASTM A829-04 13455360 ASTM A829-04 51605050 SAE J403-01 1050

High-carbon steels with specific chemical composition 5060 SAE J403-01 1060(machine components, agricultural instruments, etc.) 5070 SAE J403-01 1070

5080 SAE J403-01 1080Boron-alloy steel plates for quenching 5620 DIN EN 10083-P3-96 20MnB5and tempering 5630 DIN EN 10083-P3-96 30MnB5

8412 DIN EN 10083-P1-96 51 CrV 48414 DIN EN 10269-99 21 CrMoV 57High-strength low-alloy steel plates for 8430 DIN 30 CrMo 5 2 Specialquenching and tempering8434 DIN EN 10083-P1-96 34CrMo48440 DIN EN 10083-P1-96 C45E Special

Hot rolled low-alloy steels for military use 8416 Erdemir-04 84168613 Erdemir-03 8613

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Gra

de

Ind

ex

27




1.0128 DIN 17100 St44-2 46444444444444444545454545

1.0119 DIN 17100 QSt37-3N 471.0142 DIN 17100 QSt44-3N 47

431.0579 DIN 17100 QSt52-3N 47

696980

1.0038 DIN 17100 St37-2 (Cu) 401.0332 DIN 1614-P2 StW22 (Cu) ASTM A1011 CS Type B 341.0570 DIN 17100 St52-3 (Cu) 40

53797978787878

1.5530 791.5531 791.8159 801.7709 80

801.7220 80

807979

Ho

t R

olle

d P

rod

uct

s

28

General CharacteristicsErdemir Corresponding

And Major ApplicationsSteel

Grade Standard Grade

9240 API 5CT-01 H409255 API 5CT-01 J55Steel for casing and tubing in the 9256 API 5CT-01 J55 Specialoil and natural gas industry9257 API 5CT-01 K55 Special9280 API 5CT-01 N80 (Type 1)9030 API 5L-04 A PSL19035 API 5L-04 B PSL29042 API 5L-04 X42 PSL2

Petroleum line pipe steels suitable for use 9046 API 5L-04 X46 PSL2in conveying gas, water, and oil 9052 API 5L-04 X52 PSL2in both the oil and natural gas industries 9056 API 5L-04 X56 PSL2

9060 API 5L-04 X60 PSL29065 API 5L-04 X65 PSL29070 API 5L-04 X70 PSL2

(1) The other corresponding standards specified in the table above may be in exact or similar correspondence. Therefore, the conformity of the other related standards is not guaranteed. The corresponding standards and grades given on this table are for purposes of information only.

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Gra

de

Ind

ex

29




7676767676

EN 10208-1 L210GA 74EN 10208-1 L245GA 74EN 10208-1 L290GA 74EN 10208-1 L320GA 74EN 10208-2 L360MB 74EN 10208-2 L390MB 74EN 10208-2 L415MB 74EN 10208-2 L450MB 74EN 10208-2 L485MB 74

Ho

t R

olle

d P

rod

uct

s

30

Steel Grades

Hot Rolled Steels For Cold Reducing And Galvanizing By Hot-Dip ProcessStandard: Erdemir

Chemical Composition (%)


Hot Rolled Steels For Cold Reducing And Continuous AnnealingStandard: Erdemir

Erdemir Corresponding C Mn P S Si AI N Ti NbSteel Grade Standard Grade max. max. max. max. max. min. max. max. max.

6412 Erdemir-2004 6412 0.07 0.35 0.020 0.020 0.035 0.020 0.0100 0.010 0.005

6413 Erdemir-2004 6413 0.05 0.20 0.020 0.015 0.035 0.020 0.0070 0.010 0.005

6314 Erdemir-2004 6314 0.005 0.25 0.015 0.015 0.030 0.020 0.0060 0.03-0.07 0.020

6315 Erdemir-2004 6315 0.004 0.20 0.015 0.010 0.030 0.020 0.0060 0.02-0.06 0.020

Erdemir Corresponding C Mn P S Si AI N Ti NbSteel Grade Standard Grade max. max. max. max. max. min. max. max.

7414 Erdemir-2004 7414 0.006 0.25 0.015 0.015 0.035 0.020 0.0060 0.04-0.09 0.005

7416 Erdemir-2004 7416 0.004 0.20 0.015 0.010 0.030 0.020 0.0050 0.04-0.09 0.005

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

31


Hot Rolled Steel For Cold Reducing Standard: DIN 1614-Part1-1986


Notes1- If the content of metallic aluminium is equal to or more than 0.020, the maximum limit of nitrogen is waived.


Standard: SAE J403-2001

Standard: Erdemir


Erdemir Corresponding Chemical C Mn P S N (1) AlSteel Grade Standard Grade Limits max. .max. max. max. max. min.

6422 DIN 1614-1 St 22Standard 0.10 0.45 0.035 0.035 0.007 -

Erdemir 0.07 0.40 0.020 0.020 0.012 0.020

6423 DIN 1614-1 RRSt 23Standard 0.10 0.45 0.030 0.030 - 0.020

Erdemir 0.07 0.35 0.020 0.015 0.012 0.020

6424 DIN 1614-1 St 24Standard 0.08 0.40 0.025 0.025 - 0.020

Erdemir 0.06 0.30 0.015 0.015 0.012 0.020

Erdemir Corresponding Chemical C Mn P S SiSteel Grade Standard Grade Limits max. max. max. max. max.

6406 SAE J403 1006Standard 0.08 0.45 0.030 0.050 0.10

Erdemir 0.07 0.45 0.020 0.015 0.04

6408 SAE J403 1008Standard 0.10 0.50 0.030 0.050 0.10

Erdemir 0.08 0.50 0.020 0.015 0.05

Erdemir Corresponding C Mn P S Si Al TiSteel Grade Standard Grade max. max. max. max. max. min. max.

4437 Erdemir-2001 4437 0.17 1.00 0.020 0.015 0.03 0.020 -

5437 Erdemir-2001 5437 0.17 1.10 0.020 0.020 0.10-0.25 - -

6426 Erdemir-2002 6426 0.004 0.20 0.010 0.008 0.03 0.020 0.10

Ho

t R

olle

d P

rod

uct

s

32

Hot Rolled Steels For Cold Reducing And Manufacturing Galvanized Products Of Bake-Hardening Steels By Hot-Dip ProcessStandard: Erdemir


Hot Rolled Steels For Cold Reducing And Manufacturing Galvanized Products Of Structural Steels By Hot-Dip ProcessStandard: Erdemir


Erdemir Corresponding C Mn P S Si Al N Ti NbSteel Grade Standard Grade max. max. max. max. max. min. max. max. max.

1718 Erdemir-2004 1718 0.0060 0.30 0.020 0.015 0.035 0.020 0.0060 0.020 0.020

1722 Erdemir-2004 1722 0.0050 0.65 0.02-0.06 0.015 0.035 0.020 0.0060 0.030 0.020

1726 Erdemir-2004 1726 0.0065 0.65 0.05-0.10 0.015 0.035 0.020 0.0060 0.020 0.020

Erdemir Corresponding C Mn P S Si Al N V NbSteel Grade Standard Grade max. max. max. max. max. min. max. max. max.

1822 Erdemir-2004 1822 0.13 0.75 0.025 0.025 0.035 0.020 0.0120 - 0.008

1825 Erdemir-2004 1825 0.18 0.85 0.025 0.025 0.035 0.020 0.0120 - 0.008

1828 Erdemir-2004 1828 0.20 1.25 0.025 0.025 0.035 0.020 0.0120 - 0.008

1832 Erdemir-2004 1832 0.10 0.85 0.020 0.015 0.035 0.020 0.0090 0.060 0.070

1835 Erdemir-2004 1835 0.12 1.10 0.020 0.015 0.035 0.020 0.0090 0.070 0.070

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

33


Hot Rolled Steel For Cold Reducing For Making Electrical SteelStandard: Erdemir


Hot Rolled Low-Carbon Steels For Vitreous EnamellingStandard: Erdemir

Erdemir Corresponding C TiSteel Grade Standard Grade max. max.

6523 (1) Erdemir-2001 6523 0.05 -

7524 (1) Erdemir-2001 7524 0.01 0.15


Notes1- No mechanical test is carried out.

Erdemir Corresponding C Mn P S Si AlSteel Grade Standard Grade max. max.

5512 Erdemir-2002 5512 0.04 0.15-0.35 0.06-0.10 0.015 1.00-1.40 0.15-0.45

5513 Erdemir-2005 5513 0.03 0.15-0.35 0.06-0.10 0.015 1.10-1.50 0.15-0.45

5515 Erdemir-2004 5515 0.03 0.15-0.40 0.07-0.10 0.015 1.30-1.70 0.25-0.50

Ho

t R

olle

d P

rod

uct

s

34


Notes1- All products are made of fully killed steel having a min. aluminium of 0.02%.2- Cu = 0.20 - 0.40%.3- The mechanical properties are valid for a period of a month from the date on which the products are made available.

(In case of min. Al content of 0.020%, the mechanical properties specified for the grades 6222 and 6282 are valid for a period of 6 months.)

4- The mechanical properties are valid for a period of 6 months from the date on which the products are made available.

Hot Rolled Low-Carbon Drawing Quality Steels For Immediate Cold FormingStandard: DIN EN 10111-1998

Erdemir (1) Corresponding Chemical C Mn P S BSteel Grade Standard Grade Limits max. max. max. max. max.

6222 (3) DIN EN 10111 DD 11Standard 0.12 0.60 0.045 0.045 -Erdemir 0.07 0.40 0.020 0.020 -

6282 (2)(3) DIN EN 10111 DD 11Standard 0.12 0.60 0.045 0.045 -Erdemir 0.07 0.40 0.020 0.020 -

6223 (4) DIN EN 10111 DD 12Standard 0.10 0.45 0.035 0.035 -Erdemir 0.07 0.35 0.020 0.020 0.006

6224 (4) DIN EN 10111 DD 13Standard 0.08 0.40 0.030 0.030 -

Erdemir 0.06 0.30 0.015 0.015 0.006


Erdemir 0.07 0.35 0.015 0.015 0.006


Erdemir 0.05 0.25 0.015 0.015 -


Erdemir 0.01 0.25 0.015 0.015 -

Ho

t R

olle

d P

rod

uct

s

09

Ste

el G

rad

es

35


www.erdemir.com.tr

Mechanical Properties

Notes1- The values for the tensile test apply to “Transverse” test pieces.

ErdemirRe Rm

(1) A Bend

Steel GradeN/mm2 N/mm2 (%) (trans.,180o)

(kg/mm2) (kg/mm2) A80 A5

Corresponding 1.5 ≤ d < 2 2 ≤ d ≤ 8 1.5 ≤ d < 2 2 ≤ d < 3 3 ≤ d ≤ 8 mrbStandard Grade max. min. min. min. d:thickness

6222 DIN EN 10111 DD 11170-360 170-340 440 23 24 28 1 d

(17.3-36.7) (17.3-34.7) (44.9)

6282 DIN EN 10111 DD 11170-360 170-340 440 23 24 28 1 d

(17.3-36.7) (17.3-34.7) (44.9)

6223 DIN EN 10111 DD 12170-340 170-320 420 25 26 30 0

(17.3-34.7) (17.3-32.6) (42.8)

6224 DIN EN 10111 DD 13170-330 170-310 400 28 29 33 0

(17.3-33.7) (17.3-31.6) (40.8)

6624 DIN EN 10111 DD 13170-330 170-310 400 28 29 33 0

(17.3-33.7) (17.3-31.6) (40.8)

7222 DIN EN 10111 DD 11170-360 170-340 440 23 24 28 1 d

(17.3-36.7) (17.3-34.7) (44.9)

7224 DIN EN 10111 DD 14170-310 170-290 380 31 32 36 0

(17.3-31.6) (17.3-29.6) (38.8)

Ho

t R

olle

d P

rod

uct

s

10 36

Hot Rolled Low Carbon Steel For Cold FormingStandard: Erdemir



Notes1- The values for the tensile test apply to “Transverse” test pieces.2- Re / Rm: 0.86 max.

ErdemirCorresponding

Steel GradeUser Applied Similar C Mn P S Si Al

Sector Standard Standard max. max. max. max. max. min.

700 Automotive HES-HC-Erdemir RN08 DIN EN 10111 DD13 0.07 0.40 0.020 0.020 0.040 0.020

A80 BendCorresponding Re Rm

(1) (%) (Trans, 180o)ErdemirUser Applied Similar N/mm2 N/mm2 mrb Steel Grade

Sector Standard Standard (kg/mm2) (kg/mm2) min. (d:thickness)

700 (2) Automotive HES-HC-Erdemir RN08 DIN EN 10111 DD13220-280 320-390 31 0

(22.4-28.6) (32.7-39.8)

Ho

t R

olle

d P

rod

uct

s

11

Ste

el G

rad

es

37


www.erdemir.com.tr

Piping Steel For Ordinary UsesStandard: ASTM A53-06, Erdemir, ASTM A500-03a


ErdemirRe Rm

(1) A50

Steel GradeN/mm2 N/mm2 (%)

Corresponding (kg/mm2) (kg/mm2)Standard Grade min. min. min.

2008 Erdemir-2001 2008205 330 31

(20.9) (33.7)

2009 ASTM A53-06 A205 330 (2)

(20.9) (33.7)

4009 ASTM A53-06 A205 330 (2)

(20.9) (33.7)

6040 ASTM A500-03a B290 400 23(3)

(29.6) (40.8)


Notes1- The values for the tensile test apply to “Longitudinal” test pieces.2- A50 (%) = 1940 S0

0.2 / U 0.9 (S0: Cross-sectional area of the specimen, mm2; U: Specified tensile strength, N/mm2)3- Applies to thicknesses 4.57 mm and over. For thicknesses thinner than 4.57 mm, the minimum elongation values shall be calculated by the

formula: percent elongation in 50.8 mm = 2.40 d + 12.

Notes1- The combination of these five elements for grades 2009 and 4009 shall not exceed 1.00%. 2- For each reduction of 0.01 percentage point below the specified maximum carbon, an increase of 0.06 percentage point above the

specified maximum for manganese is permitted for grade 6040, up to a maximum of 1.50% by heat analysis.

Erdemir Corresponding Chemical C Mn (2) P S Si Cu (1) Ni (1) Cr (1) Mo (1) V (1)

Steel Grade Standard Grade Limits max. max. max. max. max. max. max. max. max. max.

2008 Erdemir-2001 2008Standard

Erdemir 0.06-0.12 0.35-0.60 0.025 0.020 0.15-0.30 0.15 0.15 0.12 0.05 0.02

2009 ASTM A53-06 AStandard 0.25 0.95 0.050 0.045 0.50 0.40 0.40 0.15 0.08

Erdemir 0.10 0.80 0.025 0.030 0.35 0.15 0.15 0.12 0.05 0.02

4009 ASTM A53-06 AStandard 0.25 0.95 0.050 0.045 0.50 0.40 0.40 0.15 0.08

Erdemir 0.12 0.70 0.025 0.020 0.05 0.15 0.15 0.12 0.05 0.02

6040 ASTM A500-03a BStandard 0.26 1.35 0.035 0.035 - - - - - -

Erdemir 0.16-0.20 0.70-0.90 0.020 0.020 0.04 - - - - -

Ho

t R

olle

d P

rod

uct

s

12 38




Notes1- For thickness of 40 mm and under, the minimum silicon is waived.

Intermediate Tensile Strength Carbon Steel Of Structural QualityStandard: ASTM A283-2003

Erdemir Corresponding Chemical C Mn P S Si (1)

Steel Grade Standard Grade Limits max. max. max. max.

3018 ASTM A283 CStandard 0.24 0.90 0.035 0.040 0.15-0.40

Erdemir 0.18 0.90 0.025 0.025 0.15-0.35

ErdemirRe Rm

(1) A

Steel GradeN/mm2 N/mm2 (%)

Corresponding (kg/mm2) (kg/mm2) A50 A200

Standard Grade min. min. min.

3018 ASTM A283 C205 380-515

23 20(20.9) (38.8-52.5)

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

39



Notes1- For material of grade 3241 of thickness equal to or thinner than 20 mm, there is no requirement for limits of manganese. 2- For each reduction of 0.01 percentage point below the specified carbon maximum, an increase of 0.06 percentage point manganese

above the specified maximum will be permitted up to the maximum of 1.35% for grade 3241.3- Copper when specified shall have a minimum content of 0.20%.4- For material of grade 3241 of thickness greater than 40 mm, the lower limit of silicon content is 0.15%.

Hot Rolled Unalloyed Structural SteelStandard: ASTM A36-2005


Notes1- The values for tensile test apply to “Transverse“ test pieces.2- Impact tests are not required for nominal thickness thinner than 6 mm.3- The impact test is carried only when specified at the time of the enquiry and order.

Erdemir Corresponding Chemical C Mn(1) (2) P S SiSteel Grade Standard Grade Limits max. max. max. max

3241 (3) (4) ASTM A36 A36Standard 0.25 0.80-1.20 0.040 0.050 0.40

Erdemir 0.20 0.80-1.35 0.030 0.025 0.40

Erdemir

Impact(2) (3)

Steel Grade

Re Rm

(1) A (%) (long.)N/mm2 N/mm2 A50 A200 Temp. KVc

Corresponding (kg/mm2) (kg/mm2) min.Standard Grade min. min. min. oC J

3241 ASTM A36 A36250 400-550

21 18 - 20 40(25.5) (40.8-56.1)

Ho

t R

olle

d P

rod

uct

s

40


Hot Rolled Unalloyed Structural SteelStandard: DIN EN 10025 - Part2 - 2004

Notes1- The maximum value for nitrogen does not apply if the chemical composition shows a minimum total aluminium content of 0.020%.2- For nominal thickness > 30 mm, C = 0.22% max.

C Mn P S Si Cu Al (1) N (1)

Erdemir d (mm)Steel Corresponding Grades ≤16 >16 >40Grade DIN EN 10025- DIN EN 10025-94 Chemical ≤40 ≤100

P2-2004 TS 2162 EN 10025-96 Limits max. max. max. max. max. max. max. max. min. max.

3237 S235JR S235JRG2Standard 0.17 0.17 0.20 1.40 0.035 0.035 - 0.55 - 0.012

Erdemir 0.17 0.17 0.18 1.00 0.025 0.025 0.40 - 0.015 0.009

3281 S235JR S235JRG2Standard 0.17 0.17 0.20 1.40 0.035 0.035 - 0.25 - 0.40 - 0.012

Erdemir 0.17 0.17 0.18 0.80 0.025 0.025 0.40 0.25 - 0.40 0.015 0.009


Erdemir 0.12 - - 0.80 0.025 0.025 0.50 - 0.015 0.009


Erdemir 0.17 0.17 - 1.00 0.025 0.020 0.08 - 0.020 0.009

6237 S235J2 +N S235J2G3Standard 0.17 0.17 0.17 1.40 0.025 0.025 - 0.55 0.020 -

Erdemir 0.12 0.17 0.17 1.20 0.020 0.020 0.40 - 0.020 0.012

3244 S275JR S275JRStandard 0.21 0.21 0.22 1.50 0.035 0.035 - 0.55 - 0.012

Erdemir 0.19 0.19 0.20 1.40 0.025 0.020 0.40 - 0.015 0.009

4244 S275JR S275JRStandard 0.21 0.21 0.22 1.50 0.035 0.035 - 0.55 - 0.012

Erdemir 0.20 0.20 - 1.30 0.020 0.020 0.04 - 0.020 0.009

6244 S275J2 +N S275J2G3Standard 0.18 0.18 0.18 1.50 0.025 0.025 - 0.55 0.020 -

Erdemir 0.18 0.18 0.18 1.40 0.020 0.020 0.40 - 0.020 0.012

3252 S355JR S355JRStandard 0.24 0.24 0.24 1.60 0.035 0.035 0.55 0.55 - 0.012

Erdemir 0.22 0.23 0.24 1.60 0.020 0.020 0.55 - 0.020 0.012

6252 (2) S355J2 +N S355J2G3Standard 0.20 0.20 0.22 1.60 0.025 0.025 0.55 0.55 0.020 -

Erdemir 0.20 0.20 0.21 1.60 0.020 0.020 0.55 - 0.020 0.012

6284 (2) S355J2 +N S355J2G3Standard 0.20 0.20 0.22 1.60 0.025 0.025 0.55 0.25-0.40 0.020 -

Erdemir 0.20 0.20 0.21 1.60 0.020 0.020 0.55 0.25-0.40 0.020 0.012

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

41



Notes1- The values for tensile test apply to “Transverse“ test pieces.2- The impact test is carried out only when specified at the time of the enquiry and order.3- Impact tests are not required for nominal thickness thinner than 6 mm.4- Only available in nominal thickness equal to or thinner than 8 mm.5- Only available in nominal thickness equal to or thinner than 25 mm.6- Only available in nominal thickness equal to or thinner than 22 mm.7- Products delivered in “+N“ condition can be hot formed and / or normalized after delivery.

Erdemir

Re (min.) Rm(1) A (%) min. Impact (3)

Steel

N/mm2 (kg/mm2) N/mm2 (kg/mm2) d (mm) (long.)d (mm) d (mm) A80 A5 Temp. KVc

Grade Corresponding ≤16 >16 >40 >63 >80 <3 ≥ 3 >1 >1.5 > 2 >2.5 ≥ 3 >40 >63 min.Standard Grade ≤40 ≤63 ≤80 ≤100 ≤100 ≤1.5 ≤ 2 ≤ 2.5 <3 ≤40 ≤63 ≤100 oC J

3237 DIN EN 10025-P2 S235JR235 225 215 215 215 360-510 360-510 16 17 18 19 24 23 22 + 20 27(2)

(24.0) (23.0) (21.9) (21.9) (21.9) (36.7-52.0) (36.7-52.0)

3281(5) DIN EN 10025-P2 S235JR235 225 - - - 360-510 360-510 16 17 18 19 24 - - + 20 27(2)

(24.0) (23.0) (36.7-52.0) (36.7-52.0)

3337 (4) DIN EN 10025-P2 S235JR235 - - - - 360-510 360-510 16 17 18 19 24 - - + 20 27(2)

(24.0) (36.7-52.0) (36.7-52.0)

4237 (5) DIN EN 10025-P2 S235JR235 225 - - - 360-510 360-510 16 17 18 19 24 - - + 20 27(2)

(24.0) (23.0) (36.7-52.0) (36.7-52.0)

6237 DIN EN 10025-P2 S235J2 +N(7)235 225 215 215 215 360-510 360-510 16 17 18 19 24 23 22 - 20 27

(24.0) (23.0) (21.9) (21.9) (21.9) (36.7-52.0) (36.7-52.0)

3244 DIN EN 10025-P2 S275JR275 265 255 245 235 430-580 410-560 14 15 16 17 21 20 19 + 20 27(2)

(28.1) (27.0) (26.0) (25.0) (24.0) (43.9-59.2) (41.8-57.1)

4244(6) DIN EN 10025-P2 S275JR275 265 - - - 430-580 410-560 14 15 16 17 21 20 19 + 20 27(2)

(28.1) (27.0) (43.9-59.2) (41.8-57.1)

6244 DIN EN 10025-P2 S275J2 +N(7)275 265 255 245 235 430-580 410-560 14 15 16 17 21 20 19 - 20 27

(28.1) (27.0) (26.0) (25.0) (24.0) (43.9-59.2) (41.8-57.1)

3252 DIN EN 10025-P2 S355JR355 345 335 325 315 510 - 680 470 - 630 13 14 15 16 20 19 18 + 20 27

(36.2) (35.2) (34.2) (33.2) (32.1) (52.0 - 69.4) (47.9 - 64.3) (2)

6252 DIN EN 10025-P2 S355J2 +N(7)355 345 335 325 315 510-680 470-630 13 14 15 16 20 19 18 - 20 27

(36.2) (35.2) (34.2) (33.2) (32.1) (52.0-69.4) (47.9-64.3)

6284 DIN EN 10025-P2 S355J2 +N(7)355 345 335 325 315 510-680 470-630 13 14 15 16 20 19 18 - 20 27

(36.2) (35.2) (34.2) (33.2) (32.1) (52.0-69.4) (47.9-64.3)

ARe Rm (1) (%) Bend (2)

Erdemir N/mm2 N/mm2 A80 A5 (trans.1800)Steel User Corresponding (kg/mm2) (kg/mm2) 1.5 ≤ d < 3 3 ≤ d ≤ 8 mrbGrade Sector Applied Standad Similar Standard min. min.

720 Automotive StW 24H-Erdemir MB01 DIN EN 10025-P2 S235JR260 - 340 370 - 450 25 30 3 d

(26.5 - 34.7) (37.7 - 45.9)

Notes1- The values for tensile test apply to “Transverse” test pieces.2- The bend test is carried out only when specified at the time of the enquiry and order.

Ho

t R

olle

d P

rod

uct

s

42


Hot Rolled Unalloyed Structural SteelStandard: Erdemir


ErdemirSteel User Corresponding C Mn P S Si AlGrade Sector Applied Standad Similar Standard max. max. max. max. max. min.720 Automotive StW 24H-Erdemir MB01 DIN EN 10025-P2 S235JR 0.12 0.70 0.020 0.020 0.040 0.020

Notes1- Product thickness ≤ 8 mm.

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

43



Hot Rolled Steel For General StructureStandard: JIS G3106-4, JIS G3101-4

Erdemir Corresponding Chemical C Mn P S SiSteel Grade Standard Grade Limits max. max. max. max. max

6050 JIS G3106-04 SM 490AStandard 0.20 1.60 0.035 0.035 0.55Erdemir 0.20 1.60 0.020 0.010 0.40

6741 JIS G3101-04 SS 400Standard - - 0.050 0.050 -Erdemir 0.18 0.60-1.00 0.020 0.015 0.05

Re Rm

(1) A(%, min.) BendErdemir N/mm2 N/mm2 d (mm) (long.,180o)Steel (kg/mm2) (kg/mm2) A50 A200 A50

Grade Corresponding d≤16 16<d≤40 40<d≤100 ≤5 >5 >16 >50 mrbStandard Grade min. min. min. ≤16 ≤50 ≤100 (d: thickness)

6050 (2) JIS G3106-04 SM 490A325 315 295 490-610 22 17 21 - -

(33.2) (32.1) (30.1) (50.0-62.2)

6741 JIS G3101-04 SS 400245 235 215 400-510 21 17 21 23 1.5 d

(25.0) (24.0) (21.9) (40.8-52.0)

Notes1- The values for tensile test apply to “Longitudinal” test pieces.2- Only available in nominal thickness equal to or thinner than 50 mm.


Ho

t R

olle

d P

rod

uct

s

44


Hot Rolled Steel With Improved FormabilityStandard: ASTM A1011 - 2005

Re Rm(1) A50 A200 Bend (2)

Erdemir N/mm2 N/mm2 (%) (%) (Trans.,180o)Steel (kg/mm2) (kg/mm2) d (mm) d (mm)Grade Corresponding 1.6 < d ≤ 2.5 2.5 < d ≤ 6.0 d ≤ 6.0 mrb

Standard Grade min. min. min. min. min. (d: thickness)

3330 ASTM A1011 SS30205 340 24 25 19 1 d

(20.9) (34.7)

3333 ASTM A1011 SS33230 360 22 23 18 1 d

(23.5) (36.7)

3336 ASTM A1011 SS36 Type1 250 365 21 22 17 1.5 d

(25.5) (37.2)

6035 ASTM A1011 SS36 Type2 250 400 - 550 20 21 16 1.5 d

(25.5) (40.8 - 56.1)

3340 ASTM A1011 SS40275 380 20 21 16 2 d

(28.1) (38.8)

3345 ASTM A1011 SS45310 410 18 19 14 2 d

(31.6) (41.8)

3350 ASTM A1011 SS50340 450 16 17 12 2.5 d

(34.7) (45.9)


Notes1- The values for tensile test apply to “Transverse” test pieces.2- The bend test is carried only when specified at the time of the enquiry and order.

ErdemirSteel Corresponding Chemical C Mn P S Cu (2) Ni Cr Mo V Nb Ti (3)

Grade Standard Grade Limits max. max. max. max. max. max. max. max. max. max. max.

3330 ASTM A1011 SS30Standard 0.25 0.90 0.035 0.040 0.20 0.20 0.15 0.06 0.008 0.008 0.025Erdemir 0.12 0.65 0.020 0.015 0.15 0.12 0.10 0.03 0.008 0.008 0.015


3336 ASTM A1011 SS36 Type1Standard 0.25 0.90 0.035 0.040 0.20 0.20 0.15 0.06 0.008 0.008 0.025Erdemir 0.14 0.85 0.020 0.015 0.15 0.12 0.10 0.03 0.008 0.008 0.015

6035 (1) ASTM A1011 SS36 Type2Standard 0.25 1.35 0.035 0.040 0.20 0.20 0.15 0.06 0.008 0.008 0.025Erdemir 0.20 1.20 0.020 0.010 0.12 0.10 0.10 0.03 0.008 0.008 0.025


3345 (1) ASTM A1011 SS45Standard 0.25 1.35 0.035 0.040 0.20 0.20 0.15 0.06 0.008 0.008 0.025Erdemir 0.19 1.30 0.020 0.015 0.15 0.12 0.10 0.03 0.008 0.008 0.015

3350 (1) ASTM A1011 SS50Standard 0.25 1.35 0.035 0.040 0.20 0.20 0.15 0.06 0.008 0.008 0.025Erdemir 0.21 1.50 0.020 0.015 0.15 0.12 0.10 0.03 0.008 0.008 0.015

Notes1- For each reduction of 0.01 percentage point below the specified carbon maximum, an increase of 0.06 percentage point manganese above

the specified maximum will be permitted up to the maximum of 1.50% for grades 3345, 3350.2- When copper bearing steel is specified, the minimum limit for copper limit is 0.20%. When copper bearing steel is not specified the

maximum limit for copper is as shown in the table. 3- The ratio of % titanium to % nitrogen shall not exceed 3.4.

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

45



Notes1- When copper bearing steel is specified, the minimum limit for copper limit is 0.20%. When copper bearing steel is not specified the

maximum limit for copper is as shown in the table. 2- The ratio of % titanium to % nitrogen shall not exceed 3.4. 3- For product greater than 20 mm in thickness, the manganese requirement is 0.80 to 1.20%. For each reduction of 0.01% below the

specified carbon maximum, an increase of 0.06% manganese above the specified maximum will be permitted up to a maximum of 1.35%.

Hot Rolled Steel With Improved FormabilityStandard: ASTM A1018 - 2006b

ErdemirSteel Corresponding Chemical C Mn P S Cu (1) Ni Cr Mo V Nb Ti (2) N (2)

Grade Standard Grade Limits max. max. max. max. max. max. max. max. max. max. max. max.

3430 ASTM A1018 SS30Standard 0.25 1.50 0.035 0.040 0.20 0.20 0.15 0.06 0.008 0.008 0.025 0.014Erdemir 0.13 0.80 0.020 0.015 0.15 0.12 0.10 0.03 0.008 0.008 0.015 0.012


3436 ASTM A1018 SS36 Type1Standard 0.25 1.50 0.035 0.040 0.20 0.20 0.15 0.06 0.008 0.008 0.025 0.014Erdemir 0.20 1.10 0.020 0.015 0.15 0.12 0.10 0.03 0.008 0.008 0.015 0.012

6036 ASTM A1018 SS36 Type2Standard 0.25 (3) 0.035 0.040 0.20 0.20 0.15 0.06 0.008 0.008 0.025 0.014Erdemir 0.20 1.35 0.020 0.010 0.12 0.10 0.10 0.03 0.008 0.008 0.025 0.014


Re Rm(1) A50 A200 Impact (2)

Erdemir N/mm2 N/mm2 (%) (%) (long.) Bend (2)

Steel (kg/mm2) (kg/mm2) d (mm) d (mm) Temp. KVc (Trans., 180o)Grade Corresponding d ≤ 25.0 4.5 ≤ d ≤ 25.0 min. mrb

Standard Grade min. min. min. min. oC J (d: thickness)

3430 ASTM A1018 SS30205 340 22 17 + 20 40 1 d

(20.9) (34.7)

3433 ASTM A1018 SS33230 360 22 16 + 20 40 1 d

(23.5) (36.7)

3436 ASTM A1018 SS36 Type1250 365 21 15 + 20 40 1.5 d

(25.5) (37.2)

6036 ASTM A1018 SS36 Type2250 400 - 550 21 18 + 20 40 2 d

(25.5) (40.8 - 56.1)

3440 ASTM A1018 SS40275 380 19 14 + 20 40 2 d

(28.1) (38.8)


Notes1- The values for tensile test apply to “Transverse” test pieces.2- The impact test and bend test are carried only when specified at the time of the enquiry and order.

Ho

t R

olle

d P

rod

uct

s

46


Notes1- The values for tensile test apply to “Transverse” test pieces.2- The impact test is carried out only when specified at the time of the enquiry and order.3- Impact tests are not required for nominal thickness thinner than 6 mm.

Bend (trans., 180o, mrb)

Notes1- The values are applicable for bend angles ≤ 90o.

Erdemir Corresponding Chemical C Mn P S Si Al BSteel Grade Standard Grade Limits max. max. max. max. max. min. max.

4044 (1) DIN EN 10025-P2 S275JRCStandard 0.21 1.50 0.035 0.035 - - -Erdemir 0.16 0.70-1.00 0.020 0.015 0.030 0.020 0.0008


Notes1- Only available in nominal thickness equal to or thinner than 8 mm.

Hot Rolled Steel With Improved FormabilityStandard: DIN EN 10025 Part2-2004

Erdemir d (mm)

Steel Grade Corresponding > 1 > 1.5 > 2.5 > 3 > 4 > 5 > 6 > 7 > 8 > 10 > 12 > 14Standard Grade ≤1.5 ≤ 2.5 ≤ 3 ≤ 4 ≤ 5 ≤ 6 ≤ 7 ≤ 8 ≤ 10 ≤ 12 ≤ 14 ≤ 16

4044 DIN EN 10025-P2 S275JRC 2 3 4 5 8 10 12 16 20 25 28 32

Erdemir

Re Rm

(1) A (%) Impact (2) (3)

Steel Grade

N/mm2 N/mm2 d (mm) (long.)(kg/mm2) (kg/mm2) A80 A5 Temp. KVc

Corresponding < 3 ≥ 3 min.Standard Grade d ≤ 8 d ≤ 8 ≤ 8 oC J

4044 DIN EN 10025-P2 S275JRC280-400 430-500 23 37 + 20 27

(28.6-40.8) (43.9-51.0)

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

47



Hot Rolled Structural Steel For Cold BendingStandard: DIN EN 10025 Part2-2004


Bend (Trans., 180o, mrb) (2)

Notes1- Impact tests are not required for nominal thickness thinner than 6 mm.2- The values are applicable for bend angles ≤ 90o.

Notes1- The values for tensile test apply to “Transverse” test pieces.

Notes

1- For nominal thickness > 30 mm, C = 0.22% max.

ErdemirImpact (1) Bend (Trans., 180o, mrb) (2)

Steel Grade(long.) (min.) d (mm)

Corresponding Temp. KVc >1 >1.5 >2.5 > 3 > 4 > 5 > 6 > 7 > 8 >10 >12 >14 >16 >18Standard Grade oC J ≤1.5 ≤ 2.5 ≤ 3 ≤ 4 ≤ 5 ≤ 6 ≤ 7 ≤ 8 ≤10 ≤12 ≤14 ≤16 ≤ 18 ≤ 20

6037 DIN EN 10025-P2 S235J2C +N - 20 27 1.6 2.5 3 5 6 8 10 12 16 20 25 28 36 406044 DIN EN 10025-P2 S275J2C +N - 20 27 2 3 4 5 8 10 12 16 20 25 28 32 40 456052 DIN EN 10025-P2 S355J2C +N - 20 27 2.5 4 5 6 8 10 12 16 20 25 32 36 45 50

ErdemirC Mn P S Si Al

Steel Graded ≤ 16 d > 16 d > 40

Corresponding Chemical d ≤ 40 d ≤ 50Standard Grade Limits max. max. max. max. max. max. max. min.

6037 DIN EN 10025-P2 S235J2C +NStandard 0.17 0.17 0.17 1.40 0.025 0.025 - 0.020Erdemir 0.12 0.17 0.17 1.00 0.020 0.010 0.10 0.020

6044 DIN EN 10025-P2 S275J2C +NStandard 0.18 0.18 0.18 1.50 0.025 0.025 - 0.020Erdemir 0.18 0.18 0.18 1.50 0.020 0.010 0.35 0.020

6052 (1) DIN EN 10025-P2 S355J2C +NStandard 0.20 0.20 0.22 1.60 0.025 0.025 0.55 0.020Erdemir 0.20 0.20 0.22 1.60 0.025 0.010 0.55 0.020

Erdemir

Re Rm

(1) A (%, min.)

Steel GradeN/mm2 (kg/mm2) N/mm2 (kg/mm2) d (mm)

A80 A5

Corresponding d ≤ 16 16 < d ≤ 40 40 < d ≤ 50 d < 3 3 ≤ d ≤50 >1 >1.5 >2 >2.5 ≥3 >40Standard Grade min. min. min. ≤1.5 ≤2 ≤2.5 <3 ≤40 ≤50

6037 DIN EN 10025-P2 S235J2C +N235 225 215 360-510 360-510 16 17 18 19 24 23

(24.0) (23.0) (21.9) (36.7-52.0) (36.7-52.0)

6044 DIN EN 10025-P2 S275J2C +N275 265 255 430-580 410-560 14 15 16 17 21 20

(28.1) (27.0) (26.0) (43.9-59.2) (41.8-57.1)

6052 DIN EN 10025-P2 S355J2C +N355 345 335 510-680 470-630 13 14 15 16 20 19

(36.2) (35.2) (34.2) (52.0-69.4) (47.9-64.3)

Ho

t R

olle

d P

rod

uct

s

48

Notes1- The maximum value for nitrogen does not apply if the chemical composition shows a minimum total aluminium content of 0.020%.



Erdemir Corresponding Chemical C Mn P S Si Al (1) N (1)

Steel Grade Standard Grade Limits max. max. max. max. min. max.

3250 DIN EN 10025-P2 E295Standard - - 0.045 0.045 - - 0.012Erdemir 0.20-0.32 0.90 0.025 0.030 0.40 0.015 0.009




Hot Rolled High-Carbon Unalloyed Structural SteelStandard: DIN EN 10025-Part2-2004

Steel

Re (min.) Rm

(1) A (%) min.Erdemir N/mm2 (kg/mm2) N/mm2 (kg/mm2) d (mm)

d (mm) d (mm) A80 A5

Grade Corresponding ≤16 >16 >40 >63 >80 <3 ≥3 >1 >1.5 >2 >2.5 ≥ 3 >40 >63Standard Grade ≤40 ≤63 ≤80 ≤100 ≤100 ≤1.5 ≤2 ≤2.5 <3 ≤40 ≤63 ≤100

3250 DIN EN 10025-P2 E295295 285 275 265 255 490-660 470-610 11 12 13 14 18 17 16

(30.1) (29.1) (28.1) (27.0) (26.0) (50.0-67.3) (47.9-62.2)

3260 DIN EN 10025-P2 E335335 325 315 305 295 590-770 570-710 7 8 9 10 14 13 12

(34.2) (33.2) (32.1) (31.1) (30.1) (60.2-78.6) (58.2-72.4)

5270 DIN EN 10025-P2 E360360 355 345 335 325 690-900 670-830 4 5 6 7 10 9 8

(36.7) (36.2) (35.2) (34.2) (33.2) (70.4-91.8) (68.4-84.7)

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

49



Notes1- For each reduction of 0.01 percentage point below the specified carbon maximum, an increase of 0.06 percentage point manganese

above the specified maximum is permitted, up to a maximum of 1.60%.2- Copper when specified shall have a minimum content of 0.20% by heat analysis.

Hot Rolled Weldable Fine Grain Structural Steel Standard: ASTM A572 - 2006


Notes1- The values for tensile test apply to “Transverse” test pieces.2- If specified at the time of the order, impact test is carried out.3- Impact tests are not required for nominal thickness thinner than 6 mm.

ErdemirSteel Corresponding Chemical C Mn (1) P S Si Al Nb V Cu (2)

Grade Standard Grade Limits max. max. max. max. min. min.

9329 ASTM A572 42 Type2Standard 0.21 0.80 - 1.35 0.04 0.05 0.40 - - 0.01 - 0.15 0.20Erdemir 0.20 0.90 - 1.40 0.02 0.02 0.25 0.02 - 0.01 - 0.10 0.20



9342 ASTM A572 60 Type3Standard 0.26 0.80 - 1.35 0.04 0.05 0.40 - 0.005 - 0.050 0.01 - 0.15 0.20Erdemir 0.20 1.20 - 1.60 0.02 0.02 0.25 0.02 0.010 - 0.050 0.02 - 0.12 0.20

Re Rm(1) A Impact (2) (3)

Erdemir N/mm2 N/mm2 (%) (long.) Steel (kg/mm2) (kg/mm2) Temp. KVcGrade Corresponding A50 A200 min.

Standard Grade min. min. min. min. oC J

9329 ASTM A572 42 Type2290 415 22 18 + 20 27

(29.6) (42.3)

9335 ASTM A572 50 Type2345 450 19 16 + 20 27

(35.2) (45.9)

9338 ASTM A572 55 Type2380 485 18 15 + 20 27

(38.8) (49.5)

9342 ASTM A572 60 Type3415 520 15 13 + 20 27

(42.3) (53.1)

Ho

t R

olle

d P

rod

uct

s

50


Notes1- Only available in nominal thickness equal to or thinner than 20 mm.2- If sufficient nitrogen-binding elements are present, the minimum total aluminium content does not apply.

Hot Rolled Weldable Fine Grain Structural Steel In Normalized Condition Standard: DIN EN 10025-Part3-2005


Notes1- The values for tensile test apply to “Transverse” test pieces.2- For product thicknesses thinner than 3 mm, the values for elongation (A80) shall be the subject of agreement at the time of ordering.3- Impact tests are not required for nominal thickness thinner than 6 mm.4- Bend tests are not required for nominal thickness thicker than 16 mm.5- If specified at the time of the order, bend test is carried out.

Erdemir Corresponding Chemical C Si Mn P S Al (2) Cr Cu Mo Nb Ni Ti V NSteel Grade Standard Grade Limits max. max. max. max. min. max. max. max. max. max. max. max. max.

9355 DIN EN 10025-3 S355NStandard 0.20 0.50 0.90-1.65 0.030 0.025 0.02 0.30 0.55 0.10 0.05 0.50 0.05 0.12 0.015Erdemir 0.19 0.40 0.90-1.65 0.020 0.010 0.02 0.30 0.10 0.05 0.05 0.35 0.03 0.08 0.012

9356 DIN EN 10025-3 S355NLStandard 0.18 0.50 0.90-1.65 0.025 0.020 0.02 0.30 0.55 0.10 0.05 0.50 0.05 0.12 0.015Erdemir 0.17 0.40 1.30-1.65 0.020 0.010 0.02 0.30 0.10 0.05 0.05 0.40 0.03 0.08 0.012

9460 (1) DIN EN 10025-3 S460NStandard 0.20 0.60 1.00-1.70 0.030 0.025 0.02 0.30 0.55 0.10 0.05 0.80 0.05 0.20 0.025Erdemir 0.19 0.60 1.40-1.70 0.020 0.010 0.02 0.10 0.10 0.08 0.05 0.40 0.03 0.15 0.012

Re Rm

(1) A5 Impact (3) Bend (4) (5)

Erdemir N/mm2 N/mm2 (%) (long.) (Trans., 180o)Steel (kg/mm2) (kg/mm2) Temp. KVcGrade Corresponding d≤16 16<d≤40 40<d≤60 min. mrb

Standard Grade min. min. min. min. oC J (d: thickness)

9355 DIN EN 10025-3 S355N355 345 335 470-630 22 - 20 40 2 d

(36.2) (35.2) (34.2) (47.9-64.3) (2)

9356 DIN EN 10025-3 S355NL355 345 335 470-630 22 - 40 31 2 d

(36.2) (35.2) (34.2) (47.9-64.3) (2)

9460 DIN EN 10025-3 S460N460 440 430 540-720 17 - 20 40 4 d

(46.9) (44.9) (43.9) (55.1-73.5) (2)

Erdemir (3)

Steel Corresponding Chemical C (1) Mn (1) P S Al Si V (2) N Nb (2) Ti (2)

Grade Standard Grade Limits max. max. max. max. min. max. max. max. max. max.

9435 ASTM A656 50 Type3Standard 0.18 1.65 0.025 0.035 0.020 0.60 0.08 0.020 0.008-0.100 -Erdemir 0.18 1.65 0.025 0.015 0.020 0.60 0.08 0.012 0.008-0.100 -

9442 ASTM A656 60 Type8Standard 0.18 1.65 0.025 0.035 0.020 0.60 0.15 0.020 0.10 0.15Erdemir 0.18 1.65 0.025 0.015 0.020 0.60 0.10 0.012 0.07 0.10



Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

51



Notes1- For each reduction of 0.01 percentage point below the specified maximum for carbon, an increase of 0.06 percentage point above the

specified maximum for manganese is permitted, up to a maximum of 1.75% for grades 9435, 9442 and 9449; and up to a maximum of 1.90% for grade 9455.

2- Nb + V + Ti = 0.008 - 0.20%.3- The maximum thicknesses of plates of grades 9435, 9442, 9449, 9455 shall be 50 mm, 40 mm, 25 mm and 20 mm respectively.

High-Strength Low-Alloy Steel With Improved FormabilityStandard: ASTM A656 - 2005


Notes1- The values for tensile test apply to “Transverse” test pieces.2- Bend test is carried out on request.

Erdemir Re Rm(1) A Bend (2)

Steel N/mm2 N/mm2 (%) (Trans., 180o)Grade Corresponding (kg/mm2) (kg/mm2) A50 A200 mrb

Standard Grade min. min. min. min. (d: thickness)

9435 ASTM A656 50 Type3345 415 21 18 1.5 d

(35.2) (42.3)

9442 ASTM A656 60 Type8415 485 17 14 1.5 d

(42.3) (49.5)

9449 ASTM A656 70 Type8485 550 14 11 1.5 d

(49.5) (56.1)

9455 ASTM A656 80 Type8550 620 12 9 1.75 d

(56.1) (63.3)

Ho

t R

olle

d P

rod

uct

s

52


Notes1- Only available in nominal thickness equal to or thinner than 16 mm.

Hot Rolled Structural Steel With High StrengthStandard: Erdemir


Notes1- The values for tensile test apply to “Transverse” test pieces.2- The impact test is carried out only when specified at the time of the enquiry and order.3- Impact tests are not required for nominal thickness thinner than 6 mm.4- The bend test is carried out only when specified at the time of the enquiry and order.

Erdemir Corresponding Chemical C Si Mn P S Al VSteel Grade Standard Grade Limits max. max. max. max. max.

735 (1) B105-10-2000 Erdemir EE01 Standard 0.17-0.22 0.55 1.60 - - 0.02-0.05 0.005

735Erdemir 0.17-0.21 0.40 1.60 0.020 0.020 0.02-0.05 0.005

ErdemirRe Rm

(1) A5 Impact (2) (3) Bend (4)

Steel N/mm2 N/mm2 (%) (long.) (trans., 180o)

Grade(kg/mm2) (kg/mm2) Temp. KVc

Corresponding min. mrbStandard Grade min. min. min. oC J (d: thickness)

735 B105-10-2000 Erdemir EE01 735345 517 20 - 20 27 2 d

(35.2) (52.7)

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

53



Notes1- The values for tensile test apply to “Longitudinal” test pieces.


Notes1- Manganese upper limit may be set at 1.00% or less by agreement between the purchaser and the supplier.

Structural Steel With Improved Atmospheric Corrosion ResistanceStandard: JIS G3125-2004

Erdemir Corresponding Chemical C Si Mn (1) P S Cu Cr NiSteel Grade Standard Grade Limits max. max. max. max.

9960 JIS G3125 SPA-HStandard 0.12 0.20-0.75 0.60 0.070-0.150 0.035 0.25-0.55 0.30-1.25 0.65Erdemir 0.12 0.20-0.75 0.60 0.070-0.150 0.020 0.25-0.55 0.30-1.25 0.65

Erdemir

A Bend

Steel

Re Rm

(1) (%) (long., 180o) Product N/mm2 N/mm2

Grade Corresponding Thickness (kg/mm2) (kg/mm2) A50 A200 mrbStandard Grade (d) min. min. min. min. (d: thickness)

d ≤ 6.0355 490 22 0.5 d

9960 JIS G3125 SPA-H (36.2) (50.0)

6.0 < d ≤ 16.0355 490 15 1.5 d

(36.2) (50.0)

Ho

t R

olle

d P

rod

uct

s

54



specified maximum for manganese is permitted, up to a maximum of 1.50% by heat analysis.

Structural Steel For BridgesStandard: ASTM A709-2006


Notes1- The values for tensile test apply to “Transverse” test pieces.2- For products of thickness less than 6 mm, the impact test is not carried out.

Erdemir Corresponding Chemical C Mn (1) P S Si Al Nb Cr Ti Cu Mo Ni VSteel Grade Standard Grade Limits max. max. max. min. max. max. max. max. max. max.

5246 ASTM A709 345F Type2Standard 0.23 0.80-1.35 0.04 0.05 0.15-0.40 - - - - - - - 0.01-0.15Erdemir 0.21 1.00-1.50 0.02 0.02 0.20-0.40 0.02 0.01 0.10 0.05 0.12 0.05 0.10 0.05-0.15

Erdemir

Steel

Re Rm

(1) A50 Impact (long.) (2)

N/mm2 N/mm2 (%) Minimum Test Value Minimum Avarage Energy(kg/mm2) (kg/mm2) Energy (J)

Temp. KVc Temp.Grade Corresponding min. 21oC 4oC -12oC

Standard Grade min. min. min. oC J

5246 ASTM A709 345F Type2345 450 19 - 30 27 34 34 34

(35.2) (45.9)

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

55



Notes1- The products are supplied in the thermomechanically rolled condition.2- Nb + Ti + V ≤ 0.22%

Hot Rolled Steel With High Yield Strength For Cold FormingStandard: DIN EN 10149-Part 2-1995


Notes1- The values for tensile test apply to “Longitudinal” test pieces.2- Impact test is carried out on request only for products with nominal thickness 6 mm.

Erdemir (1) Corresponding Chemical C Si Mn P S Al Nb (2) Ti (2) V (2)

Steel Grade Standard Grade Limits max. max. max. max. max. min. max. max. max.

4932 DIN EN 10149 S315MCStandard 0.12 0.50 1.30 0.025 0.020 0.015 0.09 0.15 0.20Erdemir 0.10 0.10 0.80 0.020 0.010 0.020 0.05 0.05 0.10





Re Rm

(1) A

ErdemirN/mm2 N/mm2 (%) Impact (2) Bend

Steel (kg/mm2) (kg/mm2) KVc (Trans., 180o)

d < 3 d ≥ 3 (long.)Grade Corresponding A80 A5 Temp. =-20 oC mdb

Standard Grade min. min. min. min. (d: thickness)

4932 DIN EN 10149 S315MC315 390-510 20 24 40 J 0

(32.1) (39.8-52.0)

4936 DIN EN 10149 S355MC355 430-550 19 23 40 J 0.5 d

(36.2) (43.9-56.1)

4942 DIN EN 10149 S420MC420 480-620 16 19 40 J 0.5 d

(42.9) (49.0-63.2)

4946 DIN EN 10149 S460MC460 520-670 14 17 40 J 1 d

(46.9) (53.1-68.4)

4950 DIN EN 10149 S500MC500 550-700 12 14 40 J 1 d

(51.0) (56.1-71.4)

Ho

t R

olle

d P

rod

uct

s

56


Hot Rolled Steel With High Yield Strength For Cold Forming Standard: Erdemir, DIN EN 10149-P2-1995


Notes1- The values for the tensile test apply to “Longitudinal” test pieces.2- Re / Rm: 0.88 max.3- Impact test is carried out on request only for products with nominal thickness ≥ 6 mm.

Notes1- Only available in nominal thickness equal to or thinner than 8 mm.2- The product is supplied in the thermomechanically rolled condition.3- N ≤ 0.005%. Cu ≤ 0.10%. Cr ≤ 0.05%. Ni ≤ 0.10%. Mo ≤ 0.10%.

ErdemirSteel User Corresponding C Mn P S Si Al Nb Ti VGrade Sector Applied Standad Similar Standard max. max. max. max. max. max. max. max.800 Automotive HE-320 DR-Erdemir RN09 DIN EN 10149-2 S315MC 0.09 0.70 0.020 0.010 0.04 - 0.05 0.01 0.02801 Automotive A3 Gr. 300-Erdemir FR06 DIN EN 10149-2 S315MC 0.08 0.60 0.020 0.010 0.12 - 0.04 0.05 0.02810 Automotive HE-360 DR-Erdemir RN10 DIN EN 10149-2 S355MC 0.10 1.25 0.020 0.010 0.04 - 0.05 0.04 0.06811 Automotive E1 Gr. 350-Erdemir FR07 DIN EN 10149-2 S355MC 0.10 1.25 0.020 0.015 0.12 - 0.05 0.04 0.06812 Automotive A4 Gr. 350-Erdemir FR08 DIN EN 10149-2 S355MC 0.08 0.80 0.020 0.010 0.12 - 0.05 0.05 0.02820 Automotive E1 Gr. 400-Erdemir FR09 DIN EN 10149-2 S420MC 0.12 1.60 0.020 0.015 0.12 - 0.07 0.05 0.07835(1) (2) (3) Automotive DIN EN 10149-P2-1995 S500MC (Special) 0.06-0.10 1.00-1.40 0.020 0.008 0.10 0.015-0.070 0.04-0.06 0.015-0.035 0.06

A50 A80 Impact (3) Bend

Erdemir Re Rm(1) (%) (%) KVc (Trans.,1800)

Steel N/mm2 N/mm2 (long.) mdb

Grade User Corresponding (kg/mm2) (kg/mm2) Temp. = - 20 oC

Sector Applied Standad Similar Standard min. min. min. min.

800 (2) Automotive HE-320 DR-Erdemir RN09 DIN EN 10149-2 S315MC320 - 385 410 - 480 - 28 - 0

(32.7 - 39.3) (41.8 - 49.0)

801 Automotive A3 Gr. 300-Erdemir FR06 DIN EN 10149-2 S315MC300 - 350 400 28 - - 0

(30.6 - 35.7) (40.8)

810 (2) Automotive HE-360 DR-Erdemir RN10 DIN EN 10149-2 S355MC360 - 435 445 - 520 - 23 - 0.5 d

(36.7 - 44.4) (45.4 - 53.1)

811 Automotive E1 Gr. 350-Erdemir FR07 DIN EN 10149-2 S355MC350 - 450 430 25 - - 0.5 d

(35.7 - 45.9) (43.9)

812 Automotive A4 Gr. 350-Erdemir FR08 DIN EN 10149-2 S355MC350 - 400 430 25 - - 0.5 d

(35.7 - 40.8) (43.9)

820 Automotive E1 Gr. 400-Erdemir FR09 DIN EN 10149-2 S420MC400 - 500 460 22 - - 0.5 d

(40.8 - 51.0) (46.9)

835 Automotive DIN EN 10149-P2-1995 S500MC (Special)500-600 550 - 680 - 20 40 J 1 d

(51.0-61.2) (56.1 - 69.4)

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

57



Wheel Steel With Low StrengthStandard: DIN EN 10111-1998

Notes1- The mechanical properties are valid for a period of 6 months from the date on which the products are made available.



Erdemir Corresponding Chemical C Mn P S AlSteel Grade Standard Grade Limits max. max. max. max. min.

3922 (1) DIN EN 10111 DD 11Standard 0.12 0.60 0.045 0.045 -Erdemir 0.09 0.50 0.020 0.010 0.02

3923 (1) DIN EN 10111 DD 12Standard 0.10 0.45 0.035 0.035 0.02Erdemir 0.09 0.45 0.020 0.010 0.02

Erdemir

Re A (%) Bend

Steel

N/mm2 (kg/mm2) Rm

(1) d (mm) (Trans.,180o)d (mm) N/mm2 A80 A5

Grade Corresponding 1.5 ≤ d < 2 2 ≤ d ≤ 8 (kg/mm2) 1.5 ≤ d < 2 2 ≤ d < 3 3 ≤ d ≤ 8 mrbStandard Grade max. min. min. min. d: thickness

3922 DIN EN 10111 DD 11170-360 170-340 440 23 24 28 1 d

(17.3-36.7) (17.3-34.7) (44.9)

3923 DIN EN 10 111 DD 12170-340 170-320 420 25 26 30 0

(17.3-34.7) (17.3-32.6) (42.8)

Ho

t R

olle

d P

rod

uct

s

58

Chemical Composition (%) (2)

Wheel Steel Of Erdemir StandardStandard: Erdemir

Notes1- Nb + Ti + V ≤ 0.22% for grade 3949.2- Cu + Cr + Ni ≤ 0.30% for grade 3949.


Notes1- The values of the tensile test for grades 3936, 3949 apply to “Transverse” test pieces.2- The values of the tensile test for grade 3945 apply to “Longitudinal” test pieces.3- Only available in nominal thickness equal to or thinner than 5 mm.4- The value for elongation is applied for material of thickness equal to or thinner than 16 mm.5- The measure for bend test is specified for mandril diameter.

Erdemir Corresponding C Mn P S Si Al V (1) Nb (1) Ti (1) Sn NSteel Grade Standard Grade max. max. max. max. max. max. max. max.

3936 Erdemir-2001 3936 0.06-0.12 0.25-0.65 0.020 0.015 0.05 0.020-0.060 - - - - -3945 Erdemir-2001 3945 0.12-0.18 0.60-0.90 0.020 0.010 0.10 0.020-0.060 - - - - -3949 Erdemir-2003 3949 0.13-0.18 1.30-1.60 0.020 0.015 0.30 0.025-0.065 - 0.05 0.05 0.010 0.009

A BendRe Rm

(1) (2) (%) (Trans., 180o)

Grade

N/mm2 (kg/mm2) N/mm2 (kg/mm2) d < 3 d ≥ 3Erdemir

Corresponding d ≤ 16 mm d ≤ 16 mm A80 A5 mrbSteel

Standard Grade min. min. min. (d: thickness)

3936 Erdemir-2001 3936225 343-441 21 25 1 d

(36.7) (35.0-45.0)

3945 (3) Erdemir-2001 3945305-390 450-510 21 25 0

(31.1-39.8) (45.9-52.0)

3949 Erdemir-2003 3949330-410 480-570 - 25 2 d

(33.7-41.8) (49.0 – 58.2) (4) (5)

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

59



Wheel Steel With Intermediate StrengthStandard: DIN EN 10025 Part2-2004

Notes1- The max. value for nitrogen does not apply if the chemical composition shows a min. total Al content of 0.020%.


Bend (Trans., 180o, mrb) (1)

Notes1- The values are applicable for bend angles ≤ 90o.

Notes1- The values for tensile test apply to “Transverse” test pieces.2- The impact test is carried out only when specified at the time of the enquiry and order.3- Impact tests are not required for nominal thickness thinner than 6 mm.4- The product of steel grade 3938 is suitable only for disc of the wheel.

Erdemir Corresponding Chemical C Mn P (2) S Si Al (1) N (1) (2)

Steel Grade Standard Grade Limits max. max. max. max. max. min. max.

3937 DIN EN 10025-P2 S235JRCStandard 0.17 1.40 0.035 0.035 - - 0.012Erdemir 0.17 0.90 0.020 0.015 0.100 0.020-0.065 0.009

3938 DIN EN 10025-P2 S275J2 +NStandard 0.18 1.50 0.025 0.025 - 0.020 -Erdemir 0.12 1.20 0.020 0.010 0.040 0.020-0.065 0.009

3944 DIN EN 10025-P2 S275JRCStandard 0.21 1.50 0.035 0.035 - - 0.012Erdemir 0.19 1.10 0.020 0.010 0.100 0.020-0.065 0.009

Erdemir d (mm)Steel Corresponding > 1 > 1.5 > 2.5 > 3 > 4 > 5 > 6 > 7 > 8 > 10 > 12 > 14Grade Standard Grade ≤1.5 ≤ 2.5 ≤ 3 ≤ 4 ≤ 5 ≤ 6 ≤ 7 ≤ 8 ≤ 10 ≤ 12 ≤ 14 ≤ 16

3937 DIN EN 10025-P2 S235JRC 1.6 2.5 3 5 6 8 10 12 16 20 25 283944 DIN EN 10025-P2 S275JRC 2 3 4 5 8 10 12 16 20 25 28 32

A (%, min.) Impact (3)

Erdemir Re Rm

(1) d (mm) (long.)Steel N/mm2 (kg/mm2) N/mm2 (kg/mm2) A80 A5 Temp. KVcGrade Corresponding d ≤ 16 16 < d ≤ 40 d < 3 3 ≤ d ≤ 40 > 1 >1.5 > 2 >2.5 ≥ 3 min.

Standard Grade min. min. ≤ 1.5 ≤ 2 ≤ 2.5 < 3 ≤ 40 oC J

3937 DIN EN 10025-P2 S235JRC 235 225 360-510 360-510 16 17 18 19 24 + 20 27 (2)

(24.0) (23.0) (36.7-52.0) (36.7-52.0)

3938(4) DIN EN 10025-P2 S275J2 +N 275 265 430-580 410-560 14 15 16 17 21 - 20 27(28.1) (27.0) (43.9-59.2) (41.8-57.1)

3944 DIN EN 10025-P2 S275JRC 275 265 430-580 410-560 14 15 16 17 21 + 20 27 (2)

(28.1) (27.0) (43.9-59.2) (41.8-57.1)

Ho

t R

olle

d P

rod

uct

s

60

Wheel Steel With Intermediate StrengthStandad: Erdemir


Notes1- Cu + Cr + Ni ≤ 0.30%.


Notes1- The values for tensile test apply to “Transverse” test pieces.2- To restrict the anisotropy of the mechanical properties, the limiting values for the samples apply longitudinally, transversely and in 45o to

the direction of rolling.

Erdemir Corresponding Chemical C Si Mn P S Al NSteel Grade Standard Grade Limits max. max. max. max. max. max.

3940 1937-02-Erdemir HL02 3940Standard 0.10 0.05 0.80 0.020 0.015 0.015-0.070 0.009Erdemir 0.10 0.04 0.80 0.020 0.015 0.020-0.065 0.009

Re Rm

(1) (2) A5 BendErdemir N/mm2 N/mm2 (%) (Trans.,180o)Steel Grade Corresponding (kg/mm2) (kg/mm2) mdb

Standard Grade min. (d: thickness)

3940 1937-02-Erdemir HL02 3940280-350 390-460 28 0.5 d

(28.6-35.7) (39.8-46.9)

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

61


ErdemirSteel Corresponding Chemical C Mn P S Si Al N Nb Ti SnGrade Standard Grade Limits max. max. max. max. max. max. max. max. max.

3946 (1) (2) 1937-03-Erdemir HL03 3946Standard 0.18 1.25 0.020 0.015 0.10 0.020 - 0.070 0.009 0.09 0.22 0.010Erdemir 0.18 0.50 - 1.00 0.020 0.015 0.10 0.020 - 0.060 0.009 0.05 0.10 0.010

Chemical Composition (%) (3) (4)

Wheel Steel With High StrengthStandard: Erdemir

Notes1- The grade 3946 also corresponds to the grade “SAPH 440” in standard JIS G3113-1990.2- Only available in nominal thickness equal to or thinner than 5 mm.3- Cu + Cr + Ni ≤ 0.30%4- V + Nb + Ti ≤ 0.22%

Re Rm(1) A5 (%) Bend

Erdemir N/mm2 N/mm2 min. (Trans., 180o)Steel (kg/mm2) (kg/mm2) d (mm) mdbGrade Corresponding ≥ 1.6 ≥ 2 ≥ 2.5 ≥ 3.15 ≥ 4 (d: thickness)

Standard Grade d < 6 mm < 2 < 2.5 < 3.15 < 4 < 6.3 d < 2 d ≥ 2

3946 1937-03-Erdemir HL03 3946305 - 420 440 - 500 29 30 32 33 34 1 d 1.5 d

(31.1 - 42.8) (44.9 - 51.0)



Ho

t R

olle

d P

rod

uct

s

62


Wheel Steel With High StrengthStandard: DIN EN 10149 Part2-1995

Notes1- The products are supplied in the thermomechanically rolled condition.2- Nb + Ti + V ≤ 0.22%.


Notes1- The values for tensile test apply to “Longitudinal” test pieces.2- The impact test is carried out only when specified at the time of the enquiry and order.3- Impact tests are not required for nominal thickness thinner than 6 mm.

Erdemir (1) Corresponding Chemical C Si Mn P S Al Nb (2) Ti (2) V (2)

Steel Grade Standard Grade Limits max. max. max. max. max. min. max. max. max.



Re Rm

(1) A Impact (2) (3) Bend

Erdemir N/mm2 N/mm2 (%) (long.) (Trans.,180o)

Steel (kg/mm2) (kg/mm2) d < 3 d ≥ 3 Temp. KVc

Grade Corresponding A80 A5 min. mdbStandard Grade min. min. min. oC J (d: thickness)

3955 DIN EN 10149 S355MC355 430-550 19 23 - 20 40 0.5 d

(36.2) (43.9-56.1)

3957 DIN EN 10149 S420MC420 480-620 16 19 - 20 40 0.5 d

(42.9) (49.0-63.3)

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

63


Chemical Composition (%) (1) (2) (3)

Wheel Steel With High StrengthStandard: Erdemir

Notes1- Cu + Cr + Ni ≤ 0.20%.2- Nb + Ti + V ≤ 0.22%.3- The product is suitable for “MAG” and “Resistance Butt” welding.

Mechanical Properties (2)

Notes1- The values for tensile test apply to “Longitudinal” test pieces.2- To restrict the anisotropy of the mechanical properties, the limiting values for the samples apply longitudinally, transversely and in 45o to

the direction of rolling.

Re Rm

(1) A5 BendErdemir N/mm2 (kg/mm2) N/mm2 (kg/mm2) (%) (Trans., 180o)Steel Grade Corresponding d ≤ 16 mm d ≤ 16 mm mrb

Standard Grade min. (d: thickness)

3960 6000-2-Erdemir HL04 3960450-550 550-650 24 0

(45.9-56.1) (56.1-66.3)

Erdemir Corresponding C Mn P S Si Al Nb Ti Sn NSteel Grade Standard Grade max. max. max. max. max. max. max. max.

3960 6000-2-Erdemir HL04 3960 0.10 1.20-1.60 0.020 0.008 0.15 0.020-0.060 0.09 0.22 0.01 0.009

Ho

t R

olle

d P

rod

uct

s

64


Disc Steel Of Wheel For Use In Automotive IndustryStandard: Erdemir

Notes1- The product must be suitable for “MAG” and “Resistance Butt” welding.2- Nb + Ti + V ≤ 0.22%.3- Cu + Cr + Ni ≤ 1.30%.4- Sn ≤ 0.01%.

Mechanical Properties (2)

Notes1- The values for tensile test apply to “Longitudinal” test pieces.2- To restrict the anisotropy of the mechanical properties, the limiting values for the samples apply longitudinally, transversely and in 45o to

the direction of rolling.3- The impact test is carried out only when specified at the time of the enquiry and order.4- Impact tests are not required for nominal thickness thinner than 6 mm.5- The material must be suitable for cold reduction and cold forming.

Erdemir Corresponding Chemical C Si Mn P S Al N Nb (2) Ti (2) Cr (3)

Steel Grade Standard Grade Limits max. max. max. max. max. max. max. max. max.

3660 (1) DP 600-Erdemir HL01 3660Standard 0.12 0.50 1.40 0.085 0.008 0.020-0.060 0.009 0.09 0.22 0.90Erdemir 0.12 0.40 1.40 0.080 0.008 0.020-0.060 0.009 0.05 0.10 0.90

Re Rm

(1) (2) A5 Impact (3) (4)

N/mm2 N/mm2 (%) (long.) BendErdemir (kg/mm2) (kg/mm2) Temp. KVc (Trans.,180o)Steel Corresponding min. mdbGrade Standard Grade min. oC J (d: thickness)

3660 (5) DP 600-Erdemir HL01 3660300-470 580-670 24 - 20 40 1.0 d

(30.6-48.0) (59.2-68.4)

Erdemir Corresponding Chemical C Mn P S Si Al Ni Cr Mo CuSteel Grade Standard Grade Limits max. min. max. max. max. min. max. max. max. max.

3701 ABS - Part 2 AStandard 0.21 2.5 x C 0.035 0.035 0.50 - - - - -Erdemir 0.18 0.60 0.025 0.020 0.40 0.020 0.15 0.10 0.05 0.15

3702 ABS - Part 2 BStandard 0.21 0.60 0.035 0.035 0.35 - - - - -Erdemir 0.18 0.60 0.025 0.020 0.35 0.020 0.15 0.10 0.05 0.15

6704 ABS - Part 2 DStandard 0.21 0.60 0.035 0.035 0.35 - - - - -Erdemir 0.21 0.70 0.020 0.015 0.35 0.020 0.15 0.10 0.05 0.15

6705 ABS - Part 2 EStandard 0.18 0.70 0.035 0.035 0.35 0.020 - - - -Erdemir 0.18 1.00 0.020 0.010 0.35 0.020 0.15 0.10 0.05 0.15

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

65



Ordinary - Strength Hull Structural Steel For ShipbuildingStandard: ABS-Part 2-2005

ImpactErdemir Re Rm

(1) A200

(2) (long.)Steel N/mm2 N/mm2 (%) Temp. KVcGrade Corresponding (kg/mm2) (kg/mm2) min.

Standard Grade min. min. oC J

3701 ABS - Part 2 A235 400 - 520 22 - -(24) (41 - 53)

3702 ABS - Part 2 B235 400 - 520 22 0 27(3) (4)

(24) (41 - 53)

6704 ABS - Part 2 D235 400 - 520 22 - 20 27

(4)

(24) (41 - 53)

6705 ABS - Part 2 E235 400 - 520 22 - 40 27

(4)

(24) (41 - 53)

Notes1- The values for the tensile test apply to “Transverse” test pieces.2- Elongation values in the table apply to plates over 40 mm to 50 mm inclusive in thickness.

The values for material 40 mm and under in thickness decrease gradually by thickness.3- For materials exceeding 25 mm in thickness, the energy values apply.4- The energy shown is minimum for full size (10 x 10 mm) specimen. The values for impact test decrease gradually by thickness.


Ho

t R

olle

d P

rod

uct

s

66

Notes1- The indicated amount of niobium and vanadium applies when any such element is used singular.2- For grade 6732, Nitrogen (N) content is 0.012% max.

Notes1- The values for the tensile test apply to “Transverse” test pieces.2- Impact tests are not required for nominal thickness thinner than 6 mm.3- Elongation values in the table apply to plates over 40 mm to 50 mm inclusive in thickness. The values for material 40 mm and under in

thickness decrease gradually by thickness.


Higher-Strength Hull Structural Steel For ShipbuildingStandard: ABS-Part2-2005


Erdemir Corresponding Chemical C Si Mn P S Al Cr Cu Mo Nb (1) Ni Ti V (1)

Steel Grade Standard Grade Limits max. max. max. max. min. max. max. max. max. max. max.

3732 ABS AH32Standard 0.18 0.50 0.90-1.60 0.035 0.035 0.020 0.20 0.35 0.08 0.02-0.05 0.40 0.02 0.05-0.10Erdemir 0.17 0.40 0.90-1.60 0.025 0.015 0.020 0.10 0.15 0.04 0.02-0.05 0.20 0.02 0.02

4732 ABS DH32Standard 0.18 0.50 0.90-1.60 0.035 0.035 0.020 0.20 0.35 0.08 0.02-0.05 0.40 0.02 0.05-0.10Erdemir 0.17 0.40 0.90-1.60 0.025 0.015 0.020 0.10 0.15 0.04 0.02-0.05 0.20 0.02 0.02

5732 ABS EH32Standard 0.18 0.50 0.90-1.60 0.035 0.035 0.020 0.20 0.35 0.08 0.02-0.05 0.40 0.02 0.05-0.10Erdemir 0.17 0.40 0.90-1.60 0.025 0.015 0.020 0.10 0.15 0.04 0.02-0.05 0.20 0.02 0.02

6732 (2) ABS FH32Standard 0.16 0.50 0.90-1.60 0.025 0.025 0.020 0.20 0.35 0.08 0.02-0.05 0.80 0.02 0.05-0.10Erdemir 0.16 0.40 0.90-1.60 0.025 0.015 0.020 0.10 0.15 0.04 0.02-0.05 0.20 0.02 0.02

Re Rm

(1) A200

(3) Impact (2)

N/mm2 N/mm2 (%) (long.)Erdemir(kg/mm2) (kg/mm2) Temp. KVcSteel

Corresponding min.GradeStandard Grade min. min. oC J

3732 ABS AH32315 440-590 22 0 31(32) (45-60)

4732 ABS DH32315 440-590 22 - 20 31(32) (45-60)

5732 ABS EH32315 440-590 22 - 40 31(32) (45-60)

6732 ABS FH32315 440-590 22 - 60 31(32) (45-60)

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

67


Notes1- The indicated amount of niobium and vanadium applies when any such element is used singular.2- For grade 6736, Nitrogen (N) content is 0.012% max.

Notes1- The values for the tensile test apply to “Transverse” test pieces.2- Impact tests are not required for nominal thickness thinner than 6 mm.3- Elongation values in the table apply to plates over 40 mm to 50 mm inclusive in thickness. The values for material 40 mm and under in

thickness decrease gradually by thickness.

Erdemir Corresponding Chemical C Si Mn P S Al Cr Cu Mo Nb (1) Ni Ti V (1)

Steel Grade Standard Grade Limits max. max. max. max. min. max. max. max. max. max. max.

3736 ABS AH36Standard 0.18 0.50 0.90-1.60 0.035 0.035 0.020 0.20 0.35 0.08 0.02-0.05 0.40 0.02 0.05-0.10

Erdemir 0.18 0.40 1.00-1.60 0.025 0.015 0.020 0.10 0.15 0.04 0.02-0.05 0.40 0.02 0.02

4736 ABS DH36Standard 0.18 0.50 0.90-1.60 0.035 0.035 0.020 0.20 0.35 0.08 0.02-0.05 0.40 0.02 0.05-0.10

Erdemir 0.18 0.40 1.00-1.60 0.025 0.015 0.020 0.10 0.15 0.04 0.02-0.05 0.40 0.02 0.02

5736 ABS EH36Standard 0.18 0.50 0.90-1.60 0.035 0.035 0.020 0.20 0.35 0.08 0.02-0.05 0.40 0.02 0.05-0.10

Erdemir 0.17 0.40 1.00-1.60 0.025 0.015 0.020 0.10 0.15 0.04 0.02-0.05 0.20 0.02 0.02

6736 (2) ABS FH36Standard 0.16 0.50 0.90-1.60 0.025 0.025 0.020 0.20 0.35 0.08 0.02-0.05 0.80 0.02 0.05-0.10

Erdemir 0.16 0.40 1.00-1.60 0.025 0.015 0.020 0.10 0.15 0.04 0.02-0.05 0.40 0.02 0.02


Higher-Strength Hull Structural SteelStandard: ABS-Part2-2005


Re Rm

(1) A200

(3) Impact (2)

Erdemir N/mm2 N/mm2 (%) (long.)Steel (kg/mm2) (kg/mm2) Temp. KVcGrade Corresponding min.

Standard Grade min. min. oC J

3736 ABS AH36355 490-620 21 0 34(36) (50-63)

4736 ABS DH36355 490-620 21 - 20 34(36) (50-63)

5736 ABS EH36355 490-620 21 - 40 34(36) (50-63)

6736 ABS FH36355 490-620 21 - 60 34(36) (50-63)

Ho

t R

olle

d P

rod

uct

s

68

Notes1- This European Standard also corresponds to the standard “NF EN 10 120 - 1997” which covers all of the grades BS1, BS2, BS3, BS4. 2- If the ratio of Al to N is not less than 2.2 or if Nb and Ti additions are applied, the nitrogen content may be 0.012% or less.


Hot Rolled Steel For Welded Gas CylindersStandard: DIN EN 10120-1997



Erdemir Corresponding (1) Chemical C Si Mn P S Al N (2) Nb TiSteel Grade Standard Grade Limits max. max. min. max. max. min. max. max. max.

6837 DIN EN 10120 P245NBStandard 0.16 0.25 0.30 0.025 0.015 0.020 0.009 0.050 0.03Erdemir 0.15 0.10 0.40 0.020 0.010 0.020 0.009 - 0.03

6842 DIN EN 10120 P265NBStandard 0.19 0.25 0.40 0.025 0.015 0.020 0.009 0.050 0.03Erdemir 0.18 0.10 0.50 0.020 0.010 0.020 0.009 - 0.03

6847 DIN EN 10120 P310NBStandard 0.20 0.50 0.70 0.025 0.015 0.020 0.009 0.050 0.03Erdemir 0.19 0.30 0.80 0.020 0.010 0.020 0.009 0.050 0.03

6852 DIN EN 10120 P355NBStandard 0.20 0.50 0.70 0.025 0.015 0.020 0.009 0.050 0.03Erdemir 0.20 0.40 1.00 0.020 0.010 0.020 0.009 0.050 0.03

A

Erdemir Re

(1) Rm (%)

Steel N/mm2 N/mm2 d < 3 3 ≤ d ≤ 5Corresponding (kg/mm2) (kg/mm2) A80 A5Grade


6837 DIN EN 10120 P245NB245 360-450 26 34

(25.0) (36.7-45.9)

6842 DIN EN 10120 P265NB265 410-500 24 32

(27.0) (41.8-51.0)

6847 DIN EN 10120 P310NB310 460-550 21 28

(31.6) (46.9-56.1)

6852 DIN EN 10120 P355NB355 510-620 19 24

(36.2) (52.0-63.2)

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

69


Notes1- Cr + Cu + Mo + Ni ≤ 0.70.%2- For thicknesses greater than 30 mm, carbon 0.22% max.3- Nb, V or other suitable grain refining elements may be used either in place or in addition to aluminium.

Notes1- The values for tensile test apply to “Transverse” test pieces.2- The tensile test for proof strength at elevated temperature is carried out on request.


Re Rm

(1) A5 Rp0,2 (1) (2)

Erdemir N/mm2 N/mm2 (%) N/mm2

Steel (kg/mm2) (kg/mm2) (kg/mm2)Grade Corresponding 3 < d ≤ 40 40 < d ≤ 50 Temp. = 300 oC

Standard Grade min. min. min. min.

6850 LR-Part 2 490FG315 305 490-610 21 192

(32.1) (31.1) (50.0-62.2) (19.6)


Intermediate Tensile Strength Carbon Steel For Pressure VesselsStandard: ASTM A285-2003



Erdemir Corresponding Chemical C Mn P SSteel Grade Standard Grade Limits max. max. max. max.

6838 ASTM A285 CStandard 0.28 0.90 0.035 0.035Erdemir 0.18 0.90 0.020 0.020


Steel For Pressure VesselsStandard: LRS.-Part2-2000 (Lloyd’s Register of Shipping)

Erdemir Corresponding Chemical C (2) Si Mn P S Al (3) Cr (1) Cu (1) Mo (1) Ni (1)

Steel Grade Standard Grade Limits max. max. max. min. max. max. max. max.

6850 LR-Part 2 490FGStandard 0.20 0.10-0.50 0.90-1.60 0.035 0.035 0.018 0.25 0.30 0.10 0.30Erdemir 0.20 0.20-0.50 1.10-1.50 0.025 0.020 0.020 0.10 0.15 0.05 0.15

Re Rm

(1) AErdemir N/mm2 N/mm2 (%)Steel Grade Corresponding (kg/mm2) (kg/mm2) A50 A200


6838 ASTM A285 C205 380-515 27 23

(20.9) (38.8-52.5)

Ho

t R

olle

d P

rod

uct

s

70


Hot Rolled Carbon Steel With Moderate And Lower Temperature Properties For Pressure PurposesStandard: ASTM A516-2006

Notes1- The values for tensile test apply to “Transverse” test pieces.2- Plates over 40 mm in thickness shall be normalized. When notch-toughness tests are required on plates 40 mm and under in thickness,

the plates shall be normalized unless otherwise specified by the purchaser.3- Impact test is carried out on request.



specified maximum for manganese is permitted, up to a maximum of 1.50% by heat analysis and 1.60% by product analysis.2- Cu + Ni + Cr + Mo ≤ 1.00.%3- Cr + Mo ≤ 0.32.%4- By agreement between the purchaser and the supplier, the heat analysis limits for vanadium, niobyum and titanium may be increased

up to 0.10% and 0.05% and 0.04% on heat analysis respectively.5- Grade 60 plates 12.5 mm and under in thickness may have 0.85-1.20% manganese on heat analysis and 0.79-1.30% manganese on product analysis.

Re Rm

(1) A Impact (3)

Erdemir (2) N/mm2 N/mm2 (%) (Trans.)

Steel (kg/mm2) (kg/mm2) Temp. KVc

Grade Corresponding A50 A200 min.Standard Grade min. min. min. oC J

6855 ASTM A516 55 205 380-515 27 23 - 40 30

(20.9) (38.8-52.6)

6860 ASTM A516 60220 415-550 25 21 - 40 30

(22.4) (42.3-56.1)

6865 ASTM A516 65240 450-585 23 19 - 40 30

(24.5) (45.9-59.7)

6870 ASTM A516 70260 485-620 21 17 - 40 30

(26.5) (49.5-63.3)

Erdemir C (1) Mn (1) (5) P S Si Cu (2) Ni (2) Cr(2) (3) Mo(2) (3) V (4) Nb (4) Ti (4)

Steel Chemical 12.5≤d 12.5<d 50<d 12.5≤d 12.5<d

Grade Corresponding Limits 50≤d 100≤d

Standard Grade max. max. max. max. max. max. max. max. max. max. max. max.

6855 ASTM A516 55Standard 0.18 0.20 0.22 0.60-0.90 0.60-1.20 0.035 0.035 0.15-0.40 0.40 0.40 0.30 0.12 0.03 0.02 0.03Erdemir 0.16 0.16 0.18 0.60-0.90 0.80-1.20 0.025 0.015 0.15-0.40 0.35 0.30 0.20 0.10 0.03 0.02 0.04




Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

71


Notes1- Where nitrogen is additionally fixed by Nb, Ti or V, the minimum aluminium content specified does not apply.2- Cr + Cu + Mo ≤ 0.45.%3- Nb + Ti + V ≤ 0.12.%


Weldable Fine Grain Steel In Normalized Condition For Pressure Purposes Standard: DIN EN 10028-Part3-2003

Notes1- The values for tensile test apply to “Transverse” test pieces.2- If agreed at the time of the enquiry and order, the 0.2% proof stress at elevated temperature shall be determined.3- For products of thickness less than 6 mm, the impact test is not carried out.


Erdemir Corresponding Chemical C Si Mn P S Al (1) Cr (2) Cu (2) Mo (2) Nb (3) Ni Ti (3) V (3)

Steel Grade Standard Grade Limits max. max. max. max. min. max. max. max. max. max. max. max.

6353 DIN EN 10028-3 P355NHStandard 0.18 0.50 1.10-1.70 0.025 0.015 0.020 0.30 0.30 0.08 0.050 0.50 0.03 0.10Erdemir 0.18 0.50 1.10-1.70 0.020 0.015 0.020 0.30 0.15 0.08 0.050 0.15 0.03 0.05

6355 DIN EN 10028-3 P355NL2Standard 0.18 0.50 1.10-1.70 0.020 0.010 0.020 0.30 0.30 0.08 0.050 0.50 0.03 0.10Erdemir 0.18 0.35 1.20-1.70 0.020 0.010 0.020 0.10 0.10 0.05 0.050 0.40 0.01 0.08

Re Rm

(1) A5 Impact (3) Rp0,2(1) (2)

N/mm2 N/mm2 (%) (Trans.) N/mm2

Erdemir (kg/mm2) (kg/mm2) (kg/mm2)Steel d (mm) Temp. KVc Temp. = 300 oCGrade Corresponding d ≤16 16<d≤40 40<d≤60 min. d≤16 16<d≤40 40<d≤60

Standard Grade min. min. min. min. oC J min. min. min.

6353 DIN EN 10028-3 P355NH355 345 335 490-630 22 - 20 30 232 225 219

(36.2) (35.2) (34.2) (50.0-64.3) (23.7) (22.9) (22.3)

6355 DIN EN 10028-3 P355NL2355 345 335 490-630 22 - 40 30 - - -

(36.2) (35.2) (34.2) (50.0-64.3)

Ho

t R

olle

d P

rod

uct

s

72

Notes1- Cr + Cu + Mo + Ni ≤ 0.70.% 2- For product thicknesses < 6 mm, a minimum manganese content of 0.20% lower than specified is permitted.


Hot Rolled Steel With Elevated Temperature Properties For Pressure PurposesStandard: DIN EN 10028-Part2-2003



Erdemir Corresponding Chemical C Si Mn P S Al Cr (1) Cu (1) Mo (1) Nb Ni (1) Ti VSteel Grade Standard Grade Limits max. max. max. max. min. max. max. max. max. max. max. max.

6335(2) DIN EN 10028-2 P235GHStandard 0.16 0.35 0.60-1.20 0.025 0.015 0.020 0.30 0.30 0.08 0.020 0.30 0.03 0.02

Erdemir 0.16 0.35 0.60-1.20 0.020 0.015 0.020 0.10 0.15 0.02 0.010 0.15 0.01 0.01

6341(2) DIN EN 10028-2 P265GHStandard 0.20 0.40 0.80-1.40 0.025 0.015 0.020 0.30 0.30 0.08 0.020 0.30 0.03 0.02

Erdemir 0.20 0.40 0.80-1.40 0.020 0.015 0.020 0.10 0.15 0.02 0.010 0.15 0.01 0.01

6347(2) DIN EN 10028-2 P295GHStandard 0.08-0.20 0.40 0.90-1.50 0.025 0.015 0.020 0.30 0.30 0.08 0.020 0.30 0.03 0.02

Erdemir 0.14-0.20 0.40 1.10-1.50 0.020 0.015 0.020 0.10 0.15 0.02 0.010 0.15 0.01 0.01

6352 DIN EN 10028-2 P355GHStandard 0.10-0.22 0.60 1.10-1.70 0.025 0.015 0.020 0.30 0.30 0.08 0.020 0.30 0.03 0.02

Erdemir 0.16-0.22 0.60 1.30-1.70 0.020 0.015 0.020 0.10 0.15 0.02 0.010 0.15 0.03 0.01

Re Rm

(1) A5 Impact (3) Rp0,2(1) (2)

ErdemirN/mm2 N/mm2 (%) (Trans.) N/mm2

Steel (kg/mm2) (kg/mm2) (kg/mm2)

Temp. KVc Temp. = 300 oCGrade Corresponding d≤16 16<d≤40 40<d≤50 min. d≤16 16<d≤40 40<d≤50


6335 DIN EN 10028-2 P235GH235 225 215 360-480 24 - 20 27 153 147 140

(24.0) (22.9) (21.9) (36.7-49.0) (15.6) (15.0) (14.3)

6341 DIN EN 10028-2 P265GH265 255 245 410-530 22 - 20 27 173 166 160

(27.0) (26.0) (25.0) (41.8-54.1) (17.6) (16.9) (16.3)

6347 DIN EN 10028-2 P295GH295 290 285 460-580 21 - 20 27 192 189 186

(30.1) (29.6) (29.1) (46.9-59.2) (19.6) (19.3) (19.0)

6352 DIN EN 10028-2 P355GH355 345 335 510-650 20 - 20 27 232 225 219

(36.2) (35.2) (34.2) (52.0-66.3) (23.7) (22.9) (22.3)

Erdemir Corresponding Chemical C Mn P S Si Al N Cr Cu Mo Ni VSteel Standard Grade Limits max. max. max. min. max. max. max. max. max.Grade

6345 DIN EN 10028-2 16Mo3Standard 0.12-0.20 0.40-0.90 0.025 0.010 0.35 0.025 0.012 0.30 0.30 0.25-0.35 0.30 -Erdemir 0.14-0.18 0.60-0.90 0.020 0.010 0.35 0.025 0.012 0.10 0.12 0.25-0.35 0.10 0.10

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

73



Hot Rolled Alloy Steel With Elevated Temperature PropertiesStandard: DIN EN 10028-Part2-2003



Re Rm

(1) A5 Impact (3) Rp0,2(1) (2)

ErdemirN/mm2 N/mm2 (%) (Trans.) N/mm2

Steel (kg/mm2) (kg/mm) (kg/mm2)

Temp. KVc Temp. = 300 oCGrade Corresponding d≤16 16<d≤40 40<d≤60 min. d≤16 16<d≤ 40 40<d≤60


6345 DIN EN 10028-2 16Mo3275 270 260 440-590 22 - 20 27 194 190 183

(28.1) (27.6) (26.5) (44.9-60.2) (19.8) (19.4) (18.7)

Erdemir Corresponding Chemical C (2) Mn (2) P S TiSteel Grade Standard Grade Limits max. max. max. max. max.

9030 API 5L A PSL1Standard 0.22 0.90 0.030 0.030 -Erdemir 0.18 0.80 0.020 0.010 0.04

9035 (1) (3) API 5L B PSL2Standard 0.22 1.20 0.025 0.015 0.04Erdemir 0.18 1.15 0.020 0.010 0.04

9042 (1) API 5L X42 PSL2Standard 0.22 1.30 0.025 0.015 0.04Erdemir 0.18 1.30 0.020 0.010 0.04







Ho

t R

olle

d P

rod

uct

s

74


Steel For Line PipeStandard: API 5L-2004

Notes1- Nb, V, Ti or combinations thereof may be used, providing that the sum of Nb, V and Ti contents shall not exceed 0.15%.2- For each reduction of 0.01% below the specified maximum carbon content, an increase of 0.05% above the specified maximum

manganese content is permissible up to a maximum of 1.50% for grades 9042 through 9052, up to a maximum of 1.65% for grades higher than X52 but less than X70, and up to 2.00% for grade X70.

3- The sum of Nb and V contents shall not exceed 0.06%, except that by agreement between the purchaser and the manufacturer.

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

75



Notes1- The values for tensile test apply to “Transverse” test pieces.2- A50 (%) = 1944 S0

0.2 / U 0.9 (S0: Cross-sectional area of the specimen, mm2; U: Specified tensile strength, N/mm2)3- Impact tests are not required nominal thickness thinner than 5 mm.4- The impact test is carried out only when specified at the time of the enquiry and order.

Steel For Line PipeStandard: API 5L-2004

Re Rm

(1) A50 Impact (3) (4)

ErdemirN/mm2 N/mm2 (%) (Trans.)


Corresponding min.Grade Standard Grade min. max. min. max. min. oC J

9030 API 5L A PSL1207 - 331 - (2) - 20 27

(21.1) - (33.8) -

9035 API 5L B PSL2241 448 414 758 (2) - 20 27

(24.6) (45.7) (42.2) (77.3)

9042 API 5L X42 PSL2290 496 414 758 (2) - 20 27

(29.6) (50.6) (42.2) (77.3)

9046 API 5L X46 PSL2317 524 434 758 (2) - 20 27

(32.3) (53.5) (44.3) (77.3)

9052 API 5L X52 PSL2359 531 455 758 (2) - 20 27

(36.6) (54.2) (46.4) (77.3)

9056 API 5L X56 PSL2386 544 490 758 (2) - 20 27

(39.4) (55.5) (50.0) (77.3)

9060 API 5L X60 PSL2414 565 517 758 (2) - 20 27

(42.2) (57.6) (52.8) (77.3)

9065 API 5L X65 PSL2448 600 531 758 (2) - 20 27

(45.7) (61.2) (54.2) (77.3)

9070 API 5L X70 PSL2483 621 565 758 (2) - 20 27

(49.3) (63.4) (57.7) (77.3)

Ho

t R

olle

d P

rod

uct

s

76


Steel For Casing And TubingStandard: API 5CT-2005


Notes1- The values for mechanical test apply to “Longitudinal” test pieces.2- The values for mechanical test apply to “Transverse” test pieces.3- A50 (%) = 1944 S0

0.2 / U 0.9 (S0: Cross-sectional area of the specimen, mm2; U: Specified tensile strength, N/mm2) 4- The value for hardness test (HV10) shall be 210 max.5- Impact tests are not required for nominal thickness thinner than 6 mm.

Notes1- Only available in nominal thickness equal to or thinner than 20 mm.2- B ≤ 0.0005%.

Re Rm A50 Impact (5)

Erdemir N/mm2 N/mm2 (%) Temp. KVcSteel Corresponding (kg/mm2) (kg/mm2) (oC) (J)Grade Standard Grade min. min. min.

9240 API 5CT H40276 - 552 414 (1) (3)

(28.2 - 56.3) (42.2)

9255 API 5CT J55379 - 552 517 (2) (3) - 20 24(2)

(38.7 - 56.3) (52.8)

9256 API 5CT J55 (Special)379 - 522 540 30 - 20 27(1)

(38.7 - 53.3) (55.1) (1)

9257 (4) API 5CT K55 (Special)390 - 552 655 22 - 20 50(2)

(39.8 - 56.3) (66.8) (2)

9280 API 5CT N80 Type1552 - 758 689 (1) (3) 0 27(1)

(56.3 - 77.3) (70.3)

ErdemirSteel Corresponding Chemical C Mn P S Si Al Ti Cu Cr Mo V Ni NbGrade Standard Grade Limits max. max. max. max. max. min. max. max. max. max. max. max. max.

9240 API 5CT H40Standard - - 0.030 0.030 - - - - - - - - -

Erdemir 0.18 1.50 0.025 0.015 0.40 0.020 - - - - - - -

9255 API 5CT J55Standard - - 0.030 0.030 - - - - - - - - -

Erdemir 0.18-0.26 1.20-1.50 0.020 0.010 0.30 0.020-0.060 - 0.30 - - - 0.10 0.050

9256 (2) API 5CT J55 (Special)Standard - - 0.030 0.030 - - - - - - - - -

Erdemir 0.21-0.25 1.25-1.45 0.020 0.010 0.15-0.30 0.015-0.050 - 0.12 0.05-0.10 0.02-0.05 0.02-0.05 0.10 0.015-0.025

9257 (1) API 5CT K55 (special)Standard 0.17 1.40 0.030 0.030 0.40 - 0.04 - 0.20 0.10 0.30 -

Erdemir 0.17 1.40 0.020 0.010 0.40 0.020-0.060 0.04 0.25 0.20 0.10 0.10 0.20 0.10

9280 API 5CT N80 Type1Standard - - 0.030 0.030 - - - - - - - - -

Erdemir 0.30-0.34 1.60-1.80 0.020 0.010 0.20-0.40 0.020-0.060 - - 0.10 0.06 0.15 0.10 0.05-0.09

Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

77


Notes1- The values for tensile test apply to “Transverse” test pieces.2- Impact tests are not required for nominal thickness thinner than 6 mm.3- The impact test and bend test are carried only when specified at the time of the enquiry and order. 4- Only available in nominal thickness equal to or thinner than 20 mm.


Hot Rolled Steel With High Strength For Safety CaseStandard: Erdemir


Re Rm

(1) A5 Impact (2) (3) Bend (3)

Erdemir N/mm2 N/mm2 (%) (long.) (Trans., 180o)


Grade Corresponding min. mrbStandard Grade min. min. min. oC J (d: thickness)

9500 (4) Erdemir-2005 9500500 690 18 - 20 30 4 d

(51.0) (70.4)

Erdemir Corresponding C Si Mn P S Al Cr Cu Mo Nb Ni Ti V NSteel Grade Standard Grade max. max. max. max. min. max. max. max. max. max. max. max. max.

9500 Erdemir-2005 9500 0.16 0.50 1.50-2.00 0.020 0.010 0.02 0.20 0.20 0.25 0.10 0.30 0.05 0.12 0.015

Ho

t R

olle

d P

rod

uct

s

78


Hot Rolled Carbon Structural Steel With Specific Chemical CompositionStandard: SAE J403-2001

Erdemir Corresponding Chemical C Mn P S SiSteel Grade Standard Grade Limits max. max. max. max. max.

6006 SAE J403 1006Standard 0.08 0.45 0.030 0.050 0.10Erdemir 0.08 0.45 0.020 0.020 0.04

3008 SAE J403 1008Standard 0.10 0.50 0.030 0.050 0.10Erdemir 0.09 0.50 0.020 0.020 0.04

3010 SAE J403 1010Standard 0.08-0.13 0.30-0.60 0.030 0.050 0.10Erdemir 0.08-0.13 0.40-0.60 0.025 0.020 0.04




3020 SAE J403 1020Standard 0.18-0.23 0.30-0.60 0.030 0.050 0.15-0.35Erdemir 0.18-0.23 0.30-0.60 0.025 0.025 0.15-0.35









Ho

t R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

79



Alloy Structural Steel PlatesStandard: ASTM A829-2004

Notes1- No mechanical test is carried out.2- This material of grade 5345 also equals to material of “SAE J404-95 Gr.1345”.3- This material of grade 5360 also equals to material of “SAE J404-95 Gr.5160”.



Hot Rolled Low - Alloy Steel With Boron For Quenching And Tempering In Untreated Condition

Standard: DIN EN 10083-Part3-1996


Hot Rolled Steel For Military UseStandard: Erdemir


Erdemir Corresponding Chemical C Mn P S Si Al Cu Cr Mo NiSteel Grade Standard Grade Limits max. max. min. max. max. max. max.

5345 (1) (2) ASTM A829 1345Standard 0.43-0.48 1.60-1.90 0.035 0.040 0.15-0.35 - - - - -Erdemir 0.43-0.48 1.60-1.90 0.025 0.025 0.15-0.35 0.15 0.25 0.20 0.05 0.20

5360 (1) (3) ASTM A829 5160Standard 0.56-0.64 0.75-1.00 0.030 0.040 0.15-0.35 0.70-0.90Erdemir 0.56-0.64 0.75-1.00 0.030 0.030 0.15-0.35 0.70-0.90

ErdemirSteel Corresponding Chemical C Mn P S Si Ti Cr BGrade Standard Grade Limits max. max. max. max. max.

5620 (1) DIN EN 10083 20 MnB 5Standard 0.17-0.23 1.10-1.40 0.035 0.040 0.40 - - 0.0008-0.0050Erdemir 0.17-0.23 1.10-1.40 0.025 0.020 0.40 0.08 0.30 0.0008-0.0050

5630 (1) DIN EN 10083 30 MnB 5Standard 0.27-0.33 1.15-1.45 0.035 0.040 0.40 - - 0.0008-0.0050Erdemir 0.27-0.33 1.15-1.45 0.025 0.020 0.40 0.08 0.30 0.0008-0.0050

Erdemir Corresponding C Mn P S Si Al Cu Cr Mo V NiSteel Grade Standard Grade max. max. max. max. max. max.

8416 (1) Erdemir-2004 8416 0.27-0.33 0.45-0.65 0.025 0.020 0.55-0.75 0.030 0.35 1.00-1.50 0.40-0.60 0.20-0.30 0.258613 (1) Erdemir-2003 8613 0.11-0.15 0.60-0.90 0.025 0.015 0.30-0.50 0.02-0.07 0.20 0.20 - - 0.60-0.90

Ho

t R

olle

d P

rod

uct

s

80


Notes1- No mechanical test is carried out.2- Cr + Mo + Ni ≤ 0.63%.3- P + S ≤ 0.020%.

Hot Rolled Low - Alloy Steel For Quenching And Tempering In Untreated ConditionStandard: DIN EN 10083-P1-96, DIN EN 10269-99, DIN 30CrMo52

Chemical Composition (%) (2) (4)

Steel Of Casted Slab (1)

Standard: Erdemir

Notes1- The other products to be ordered as casted slab are the steels of grades 700, 3008, 3010, 3012, 3015, 3020, 3030, 5035, 5040, 5045,

5050, 5360, 6006, 6018, 6222, 6223, 6224, 6282.2- Casted slab is a type of product in the range of thickness of which is from 61 mm up to 200 mm including.3- The steel of grade 3995 is only produced in dimensions of casted slab.4- No mechanical test is applied for casted slabs.

ErdemirSteel Corresponding Chemical C Mn P S Al Si Cr Ni V MoGrade Standard Grade Limits max. max. max. max. max. max. max.

8412 (1) DIN EN 10083-P1-96 51CrV4Standard 0.47 - 0.55 0.70 - 1.10 0.035 0.035 - 0.40 0.90 - 1.20 - 0.10 - 0.25 -

Erdemir 0.47 - 0.55 0.70 - 1.10 0.030 0.030 - 0.40 0.90 - 1.20 - 0.10 - 0.25 -

8414 (1) DIN EN 10269-99 21CrMoV57Standard 0.17 - 0.25 0.40 - 0.80 0.030 0.030 0.030 0.40 1.20 - 1.50 0.60 0.20 - 0.35 0.55 - 0.80

Erdemir 0.17 - 0.25 0.40 - 0.80 0.030 0.030 0.030 0.40 1.20 - 1.50 0.60 0.20 - 0.35 0.55 - 0.80

8430 (1) DIN 30CrMo5 2 (Special)Standard 0.27 - 0.32 0.50 - 0.80 0.010 0.010 0.050 0.10 - 0.40 1.00 - 1.50 - - 0.10 - 0.30

Erdemir 0.27 - 0.32 0.50 - 0.80 0.010 0.010 0.050 0.10 - 0.40 1.00 - 1.50 - - 0.10 - 0.30

8434 (1) (3) DIN EN 10083-P1-96 34CrMo4Standard 0.30 - 0.37 0.60 - 0.90 0.015 0.010 - 0.40 0.90 - 1.20 - - 0.15 - 0.30

Erdemir 0.30 - 0.37 0.60 - 0.90 0.010 0.010 0.050 0.30 0.90 - 1.15 - - 0.20 - 0.27

8440(1) (2) DIN EN 10083-P1-96 C45E (Special)Standard 0.42 - 0.50 0.50 - 0.80 0.035 0.035 - 0.40 0.40 0.40 - 0.10

Erdemir 0.42 - 0.48 0.95 - 1.30 0.030 0.030 - 0.40 0.20 - 0.40 0.20 - 0.05

Erdemir Corresponding C Mn P S Si Ti Nb NSteel Grade Standard Grade max. max. max. max. max. max. max. max.

3995 (3) Erdemir-2001 3995 0.20 1.65 0.025 0.020 0.55 0.05 0.10 0.012

Ho

t R

olle

d P

rod

uct

s

81


www.erdemir.com.tr

Ava

ilab

le S

izes

Product General Thickness Range (mm)

Symbol Min. Max.

HCKK 1.50 6.00 Hot rolled coil with mill edge for cold rolling

BCKK 1.50 6.00 Hot rolled coil with mill edge processed in recoiling line for cold rolling

TCKK 1.50 6.00 Hot rolled coil with mill edge skin-passed in recoiling line for cold rolling

RKK 1.50 10.00 Hot rolled coil with mill edge

BRKK 1.50 6.50 Hot rolled coil with mill edge processed in recoiling line

KRKK 7.00 25.00 Hot rolled heavy-thickness coil with mill edge

TRKK 1.50 6.50 Hot rolled skin-passed coil with mill edge

R 1.50 6.50 Hot rolled coil with trimmed edge

TR 1.50 6.50 Hot rolled skin-passed coil with trimmed edge

RP 1.50 8.00 Hot rolled, pickled coil with trimmed edge

TRP 1.50 5.00 Hot rolled, skin-passed, pickled coil with trimmed edge

TRPKK 1.50 6.50 Hot rolled, skin-passed, pickled coil with mill edge

RPKK 1.50 16.00 Hot rolled, pickled coil with mill edge

MRKK 4.00 10.00 Hot rolled, patterned coil with mill edge

RD 2.00 6.35 Hot rolled, slitted coil

RPD 2.00 6.35 Hot rolled, pickled, slitted coil

TRPD 2.00 6.35 Hot rolled, skin-passed, pickled, slitted coil

THRU 1.50 4.99 Hot rolled, skin-passed sheet cut from coil with trimmed edge

HRU 1.50 4.99 Hot rolled sheet cut from coil with trimmed edge

HRUKK 1.50 4.99 Hot rolled sheet cut from coil with mill edge

HRP 1.50 4.99 Hot rolled, pickled sheet cut from coil with trimmed edge

THRP 1.50 4.99 Hot rolled, skin-passed and pickled sheet cut from coil with trimmed edge

THRPK 1.50 4.99 Hot rolled, skin-passed and pickled sheet cut from coil with mill edge

HRPKK 1.50 4.99 Hot rolled, pickled sheet cut from coil with mill edge

LP 5.00 15.00 Hot rolled, pickled plate cut from coil with trimmed edge

LPKK 5.00 15.00 Hot rolled, pickled plate cut from coil with mill edge

TLP 5.00 6.50 Hot rolled, skin-passed and pickled sheet cut from coil with trimmed edge

TLPKK 5.00 6.50 Hot rolled, skin-passed and pickled sheet cut from coil with mill edge

LR 5.00 15.00 Hot rolled plate cut from coil with trimmed edge

LRKK 5.00 15.00 Hot rolled plate cut from coil with mill edge

L 6.00 100.00 Heavy plate with trimmed edge

LKK 6.00 100.00 Heavy plate with mill edge

DS 61.00 200.00 Casted slab (extra heavy plate with mill edge)

Hot Rolled Products

Available Sizes

Ho

t R

olle

d P

rod

uct

s

82

Notes1- The minimum width is 700 mm.2- The maximum thickness to be ordered for grades 3938, 3940, 3945, 3946, 6837, 6842, 6847, 6852 is 5.00 mm.3- The maximum thickness to be ordered for grades 3330, 3333, 3336, 3340, 3345, 3350, 6035 is 6.00 mm.4- The maximum thickness to be ordered for grades 720, 835, 3337, 3660, 4044 is 8.00 mm.5- The order limits of thickness for grades 7224, 7524 are min. 2.60 mm and max. 6.00 mm.6- The minimum thickness to be ordered for grades 3430, 3433, 3436, 3440, 6036, 6222, 6223, 6224, 6624, 7222 is 6.01 mm.7- Orders for grades 6222, 6223, 6224, 6624, 7222 of products 6 mm and under in thickness are subject to negotiation.8- Orders for grade 9060 of products in range of 5.00-7.00 mm in thickness (5.00 mm ≤ nominal thickness ≤ 7.00 mm) and in range of

750-1250 mm in width (750 mm ≤ nominal width ≤ 1250 mm) are subject to negotiation. No ordering for other sizes of grade 9060.9- Orders for grade 9065 of products in range of 5.00-7.00 mm in thickness (5.00 mm ≤ nominal thickness ≤ 7.00 mm) and in range of

750-1050 mm in width (750 mm ≤ nominal width ≤ 1050 mm) are subject to negotiation. No ordering for other sizes of grade 9065.

RKK Hot rolled coil with mill edge

Dimensions

Thickness(mm)Maximum Width (mm)

Group 1 Group 2 Group 3 Group 4 Group 5 Group 61.50 - 1.79 1125 10251.80 - 1.99 1225 11252.00 - 2.09 1225 1225 1025 925 9302.10 - 2.29 1325 1225 1025 925 9302.30 - 2.49 1425 1225 1125 1025 10302.50 - 2.79 1525 1325 1225 1125 1130 10252.80 - 2.99 1525 1425 1325 1225 1230 10253.00 - 3.19 1525 1525 1425 1325 1230 11253.20 - 3.49 1525 1525 1425 1325 1330 11253.50 - 3.59 1525 1525 1525 1425 1330 12253.60 - 3.99 1525 1525 1525 1425 1430 12254.00 - 4.49 1525 1525 1525 1525 1530 13254.50 - 4.99 1525 1525 1525 1525 1530 14255.00 - 10.00 1525 1525 1525 1525 1530 1525

GradesGroup Code Grades1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 3433, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3436, 3440, 3701, 3702, 3940, 3944, 4044, 4244, 60186035, 6036, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

4 3945, 3946, 6847, 6852, 9035, 9052, 9060, 9255, 9256, 99605 800, 801, 810, 811, 812, 3955, 4932, 4936

6

735, 820, 835, 3030, 3250, 3252, 3260, 3350, 3660, 3732, 3736, 3949, 3957, 3960, 4732, 4736, 4942, 4946,4950, 5035, 5040, 5045, 5050, 5060, 5070, 5080, 5246, 5270, 5360, 5620, 5630, 6050, 6052, 6252, 6284, 6345, 6347, 6352, 6353, 6355, 6704, 6850, 6855, 6860, 6865, 6870, 9065, 9257, 7224, 7524, 9280, 9335, 9338, 9342, 9355, 9356, 9435, 9442, 9449, 9455, 9460, 9500

Ho

t R

olle

d P

rod

uct

s

83


www.erdemir.com.tr

Ava

ilab

le S

izes

Notes1- The minimum width is 700 mm.2- The maximum thickness to be ordered for grades 3938, 3940, 3945, 3946, 6837, 6842, 6847, 6852 is 5.00 mm.3- The maximum thickness to be ordered for grades 3330, 3333, 3336, 3340, 3345, 3350, 6035 is 6.00 mm.4- The minimum thickness to be ordered for grades 3430, 3433, 3436, 3440, 6036, 6222, 6223, 6224, 6624, 7222 is 6.01 mm.5- The order limit of thickness for grades 7224, 7524 is min. 2.60 mm.6- Orders for grades 6222, 6223, 6224, 6624, 7222 of products 6 mm and under in thickness are subject to negotiation.7- Orders for grade 9060 of products in range of 5.00-6.00 mm in thickness (5.00 mm ≤ nominal thickness ≤ 6.00 mm) and in range of

750-1250 mm in width (750 mm ≤ nominal width ≤ 1250 mm) are subject to negotiation. No ordering for other sizes of grade 9060.8- Orders for grade 9065 of products in range of 5.00-6.00 mm in thickness (5.00 mm ≤ nominal thickness ≤ 6.00 mm) and in range of

750-1050 mm in width (750 mm ≤ nominal width ≤ 1050 mm) are subject to negotiation. No ordering for other sizes of grade 9065.9- No limitation for coil weight.

BRKK Hot rolled coil with mill edge processed in recoiling line

Dimensions

Thickness (mm)Maximum Width (mm)

Group 1 Group 2 Group 3 Group 4 Group 5 Group 61.50 - 1.79 1125 10251.80 - 1.99 1225 11252.00 - 2.09 1225 1225 1025 925 9302.10 - 2.29 1325 1225 1025 925 9302.30 - 2.49 1425 1225 1125 1025 10302.50 - 2.79 1525 1325 1225 1125 1130 10252.80 - 2.99 1525 1425 1325 1225 1230 10253.00 - 3.19 1525 1525 1425 1325 1230 11253.20 - 3.49 1525 1525 1425 1325 1330 11253.50 - 3.59 1525 1525 1525 1425 1330 12253.60 - 3.99 1525 1525 1525 1425 1430 12254.00 - 4.49 1525 1525 1525 1525 1530 13254.50 - 4.99 1525 1525 1525 1525 1530 14255.00 - 6.00 1525 1525 1525 1525 1530 15256.01 - 6.50 1525 1525 1525


2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 3433, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3436, 3440, 3701, 3702, 3940, 3944, 4044, 4244, 6018, 6035, 6036, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

4 3945, 3946, 6847, 6852, 9035, 9052, 9060, 9255,5 9256, 9960, 800, 801, 810, 811, 812, 3955, 4932, 4936

6

735, 820, 835, 3030, 3250, 3252, 3260, 3350, 3660, 3732, 3736, 3949, 3957, 3960, 4732, 4736, 4942, 4946, 4950, 5035, 5040, 5045, 5050, 5060, 5070, 5080, 5246, 5270, 5360, 5620, 5630,6050, 6052, 6252, 6284, 6345, 6347, 6352, 6353, 6355, 6704, 6850, 6855, 6860, 6865, 6870, 7224, 7524, 9065, 9257, 9280, 9335, 9338, 9342, 9355, 9356, 9435, 9442, 9449, 9455, 9460, 9500

Ho

t R

olle

d P

rod

uct

s

84

Notes1- The minimum width is 800 mm.2- Orders for product in range of 1511-1525 mm in width are subject to negotiation.3- Orders for grades of Group-4 and Group-5 of products in range of 7.00-7.99 mm in thickness (7.00 mm ≤ nominal thickness ≤ 7.99 mm) are

subject to negotiation.4- The maximum thickness to be ordered for grades 720, 835, 3337, 4044 is 8.00 mm.5- The maximum thickness to be ordered for grades 735, 3960, 4950 is 16.00 mm.6- The maximum thickness to be ordered for grades 801, 810, 811, 812, 4932, 4936 is 20.00 mm.

KRKK Hot rolled heavy-thickness coil with mill edge

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 57.00 - 7.99 1425 1425 14258.00 - 8.99 1510 1510 1510 1510 12259.00 - 20.00 1510 1510 1510 1510 151020.01 - 22.00 1510 1510 151022.01 - 25.00 1510 1510

GradesGroup Code Grades1 700, 3008, 3430, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3237, 3281, 3337, 3433, 3936, 3937, 4237, 4437, 5437, 6037, 9030

3800,801, 810, 811, 812, 3018, 3020, 3241, 3244, 3436, 3440, 3701, 3702, 3732, 3736, 3944, 4044, 4244, 4732, 4736, 4932, 6018, 6036, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 9035, 9042, 9046, 9240, 9329

4

735, 820, 835, 3030, 3250, 3252, 3260, 3949, 3955, 3957, 39604936, 4942, 4946, 4950, 5035, 5040, 5045, 5050, 5246, 52705620, 5630, 6050, 6052, 6252, 6284, 6345, 6347, 6352, 63536355, 6704, 6850, 9052, 9056, 9255, 9256, 9257, 9335, 9338, 9435

55060, 5070, 5080, 5360, 6855, 6860, 6865, 6870, 8434, 9060, 9065, 9070, 9280, 9342, 9355, 9356, 9442, 9449, 9455, 9460, 9500, 9960

Ho

t R

olle

d P

rod

uct

s

85


www.erdemir.com.tr

Ava

ilab

le S

izes

Notes1- The minimum width is 700 mm.2- The suitability for enamelling is not guaranteed for the cold rolled products produced from steel grades of the product types HCKK,

TCKK, BCKK.3- No limitation for coil weight.4- No mechanical test is carried out.

HCKK Hot rolled coil with mill edge for cold rolling

TCKK Hot rolled coil with mill edge skin-passed in recoiling line for cold rolling

BCKK Hot rolled coil with mill edge processed in recoiling line for cold rolling

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 51.50 - 1.79 1130 10301.80 - 1.99 1230 11302.00 - 2.09 1230 1230 10302.10 - 2.19 1330 1230 10302.20 - 2.29 1330 1230 1030 9302.30 - 2.49 1430 1230 1130 9302.50 - 2.59 1530 1330 1230 9302.60 - 2.69 1530 1330 1230 1030 10302.70 - 2.79 1530 1330 1230 1030 11302.80 - 2.94 1530 1430 1330 1130 12302.95 - 2.99 1530 1430 1330 1230 12303.00 - 3.19 1530 1530 1430 1230 12303.20 - 3.29 1530 1530 1430 1230 13303.30 - 3.49 1530 1530 1430 1330 13303.50 - 3.59 1530 1530 1530 1330 13303.60 - 3.99 1530 1530 1530 1430 13304.00 - 4.19 1530 1530 1530 1430 15304.20 - 6.00 1530 1530 1530 1530 1530

GradesGroup Code Grades1 6406, 6408, 6412, 6413, 6422, 6423, 6424, 65232 1822, 1825, 4437, 54373 1828, 55124 1832, 1835, 5513, 55155 1718, 1722, 1726, 6314, 6315, 6426, 7414, 7416

Ho

t R

olle

d P

rod

uct

s

86

Notes1- The minimum width is 700 mm.2- Orders for the grades other than grades in the table above are subject to negotiation.3- The maximum thickness to be ordered for grades 3337, 4044 is 8.00 mm.4- No ordering for heavy coil produced from the slab in length of 12 m.5- The standard pattern in ERDEMIR is given below.6- Request for the change of pattern is acceptable for orders of a minimum of 2000 tons and is subject to negotiation.

MRKK Hot rolled, patterned coil with mill edge

Dimensions

Thickness (mm)Maximum width (mm)

Group 1 Group 2 Group 3 Group 4 Group 5 Group 64.00 - 4.99 1225 12255.00 - 5.99 1325 13256.00 - 10.00 1425 1425

GradesGroup Code Grades2 3237, 3337, 4237, 60373 3241, 3244, 4044, 4244, 6044, 6237, 6244

L = 25 mm ± 2 mmS = 25 mm ± 2 mmt = 4-10 mm h = 1.5-2.5 mm

W = 9 mma = 45 ~ 60° R = 35 ~ 70 mmr = 35 mm b = 40 mm

AA- CROS SECTION

BB- CROS SECTION

Ho

t R

olle

d P

rod

uct

s

87


www.erdemir.com.tr

Ava

ilab

le S

izes

Notes1- The minimum width is 700 mm.2- The maximum thickness to be ordered for grades 3938, 3940, 6837, 6842 is 5.00 mm.3- The maximum thickness to be ordered for grades 3330, 3333, 3336, 3340, 3345, 6035 is 6.00 mm.4- The minimum thickness to be ordered for grades 3430, 3433, 3436, 3440, 6036, 6222, 6223, 6224, 6624, 7222 is 6.01 mm.5- Orders for grades 6222, 6223, 6224, 6624, 7222 of products 6 mm and under in thickness are subject to negotiation.6- No limitation for coil weight.

R Hot rolled coil with trimmed edge

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 5 Group 61.50 - 1.79 1100 10001.80 - 1.99 1200 11002.00 - 2.09 1200 1200 10002.10 - 2.29 1300 1200 10002.30 - 2.49 1400 1200 11002.50 - 2.59 1500 1300 12002.60 - 2.79 1500 1300 1200 10002.80 - 2.99 1500 1400 1300 10003.00 - 3.49 1500 1500 1400 11003.50 - 3.99 1500 1500 1500 12004.00 - 4.49 1500 1500 1500 13004.50 - 4.99 1500 1500 1500 14005.00 - 6.00 1500 1500 1500 15006.01 - 6.50 1500 1500 1500


2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 3433, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3436, 3440, 3701, 3702, 3940, 3944, 4044, 4244, 6018, 6035, 6036, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

6 7224, 7524

Ho

t R

olle

d P

rod

uct

s

88

Notes1- The minimum width is 700 mm.2- The upper limits of width for product type TR are determined by subtracting 25 mm from the upper limits of widths specified for each

individual range of thickness.3- No limitation for coil weight.4- The maximum thickness to be ordered for grades 3938, 3940, 6837, 6842 is 5.00 mm.5- The maximum thickness to be ordered for grades 3330, 3333, 3336, 3340, 3345, 6035 is 6.00 mm.6- The minimum thickness to be ordered for grades 3430, 3433, 3436, 3440, 6036 is 6.01 mm.

TR Hot rolled skin-passed coil with trimmed edge

TRKK Hot rolled skin-passed coil with mill edge

Dimensions




2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 3433, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3436, 3440, 3701, 3702, 3940, 3944, 4044, 4244, 6018, 6035, 6036, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

6 7224, 7524

Ho

t R

olle

d P

rod

uct

s

89


www.erdemir.com.tr

Ava

ilab

le S

izes

Notes1- The minimum width is 700 mm.2- Orders for the grades of Group-6 except for 7224, 7524 are not accepted in case of HRU.3- The minimum thickness to be ordered for grades 7224, 7524 is 2.60 mm.4- Orders for products of grades 6222, 6223, 6224, 6624, 7222 are subject to negotiation.5- The upper limits of width for product type HRU are determined by subtracting 25 mm from the upper limits of widths specified for each

individual range of thickness.6- a) For thicknesses ≤ 4.00 mm, the nominal lengths are between 1500 mm and 6000 mm.

b) For thicknesses > 4.00 mm, the nominal lengths are between 1500 mm and 15000 mm.7- a) For the nominal length ≤ 4000 mm, maximum bundle weight is 7 t.

b) For the nominal length > 4000 mm, no limitation for bundle weight.

HRU Hot rolled sheet cut from coil with trimmed edge

HRUKK Hot rolled sheet cut from coil with mill edge

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 5 Group 61.50 - 1.79 1125 10251.80 - 1.99 1225 11252.00 - 2.09 1225 1225 1025 925 9302.10 - 2.29 1325 1225 1025 925 9302.30 - 2.49 1425 1225 1125 1025 10302.50 - 2.79 1525 1325 1225 1125 1130 10252.80 - 2.99 1525 1425 1325 1225 1230 10253.00 - 3.19 1525 1525 1425 1325 1230 11253.20 - 3.49 1525 1525 1425 1325 1330 11253.50 - 3.59 1525 1525 1525 1425 1330 12253.60 - 3.99 1525 1525 1525 1425 1430 12254.00 - 4.49 1525 1525 1525 1525 1530 13254.50 - 4.99 1525 1525 1525 1525 1530 1425


2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333,3337, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3701, 3702, 3940, 3944, 4044, 4244, 6018, 6035, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

4 3945, 3946, 6847, 6852, 9035, 9052, 9255, 9256, 99605 800, 801, 810, 811, 812, 3955, 4932, 4936

6

735, 820, 835, 3030, 3250, 3252, 3260, 3350, 3660, 3732, 3736, 3949, 3957, 3960, 4732, 4736, 4942, 4946, 4950 5035, 5040, 5045, 5050, 5060, 5070, 5080, 5246, 5270, 5360, 5620, 5630, 6050, 6052, 6252, 6284, 6345, 6347, 6352, 6353, 6355, 6704, 6850, 6855, 6860, 6865, 6870, 7224, 7524, 9257, 9280, 9335, 9338, 9342, 9355, 9356, 9435, 9442, 9449, 9455, 9460, 9500

Ho

t R

olle

d P

rod

uct

s

90

Notes1- The minimum width is 700 mm.2- a) For thicknesses ≤ 4.00 mm, the nominal lengths are between 1500 mm and 6000 mm.

b) For thicknesses > 4.00 mm, the nominal lengths are between 1500 mm and 15000 mm.3- a) For the nominal length ≤ 4000 mm, maximum bundle weight is 7 t.

b) For the nominal length > 4000 mm, no limitation for bundle weight.4- No request is accepted for normalizing.

THRU Hot rolled, skin-passed sheet cut from coil with trimmed edge

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 5 Group 61.50 - 1.79 1100 10001.80 - 1.99 1200 11002.00 - 2.09 1200 12002.10 - 2.29 1300 12002.30 - 2.49 1400 12002.50 - 2.59 1500 13002.60 - 2.79 1500 1300 10002.80 - 2.99 1500 1400 10003.00 - 3.49 1500 1500 11003.50 - 3.99 1500 1500 12004.00 - 4.49 1500 1500 13004.50 - 4.99 1500 1500 1400

GradesGroup Code Grades

1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

6 7224, 7524

Ho

t R

olle

d P

rod

uct

s

91


www.erdemir.com.tr

Ava

ilab

le S

izes

Notes1- The minimum width is 700 mm.2- The upper limits of width for product type HRP are determined by subtracting 25 mm from the upper limits of widths specified for each

individual range of thickness.3- The minimum thickness to be ordered for grades 7224, 7524 is 2.60 mm.4- Orders for products of grades 6222, 6223, 6224, 6624, 7222 are subject to negotiation.5- Length: min. 1500 mm, max. 6000 mm.6- a) For the nominal length ≤ 4000 mm, maximum bundle weight is 7 t.


HRP Hot rolled, pickled sheet cut from coil with trimmed edge

HRPKK Hot rolled, pickled sheet cut from coil with mill edge

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 5 Group 61.50 - 1.79 1125 10251.80 - 1.99 1225 11252.00 - 2.09 1225 1225 1025 925 9302.10 - 2.29 1325 1225 1025 925 9302.30 - 2.49 1425 1225 1125 1025 10302.50 - 2.79 1525 1325 1225 1125 1130 10252.80 - 2.99 1525 1425 1325 1225 1230 10253.00 - 3.19 1525 1525 1425 1325 1230 11253.20 - 3.49 1525 1525 1425 1325 1330 11253.50 - 3.59 1525 1525 1525 1425 1330 12253.60 - 3.99 1525 1525 1525 1425 1430 12254.00 - 4.49 1525 1525 1525 1525 1530 13254.50 - 4.99 1525 1525 1525 1525 1530 1425


1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3701, 3702, 3940, 3944, 4044, 4244, 6018, 6035, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

4 3945, 3946, 6847, 6852, 9035, 9052, 9255, 9256, 99605 800, 801, 810, 811, 812, 3955, 4932, 4936

6

735, 820, 835, 3030, 3250, 3252, 3260, 3350, 3660, 3732, 3736, 3949, 3957, 3960, 4732, 4736, 4942, 4946 4950, 5035, 5040, 5045, 5050, 5060, 5070, 5080, 5246, 5270, 5360, 5620, 5630, 6050, 6052, 6252, 6284, 6345, 6347, 6352, 6353, 6355, 6704, 6705, 6850, 6855, 6860, 6865, 6870, 7224, 7524, 9257, 9280, 9335, 9338, 9342, 9355, 9356, 9435, 9442, 9449, 9455, 9460, 9500

Ho

t R

olle

d P

rod

uct

s

92

Notes1- The minimum width is 700 mm.2- The upper limits of width for product type THRP are determined by subtracting 25 mm from the upper limits of widths specified for each

individual range of thickness. 3- Length: min. 1500 mm, max. 6000 mm.4- a) For the nominal length ≤ 4000 mm, maximum bundle weight is 7 t.

b) For the nominal length > 4000 mm, no limitation for bundle weight.5- No request is accepted for normalizing.

THRP Hot rolled, skin-passed and pickled sheet cut from coil with trimmed edge

THRPK Hot rolled, skin-passed and pickled sheet cut from coil with mill edge

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 5 Group 61.50 - 1.79 1125 10251.80 - 1.99 1225 11252.00 - 2.09 1225 12252.10 - 2.29 1325 12252.30 - 2.49 1425 12252.50 - 2.59 1525 13252.60 - 2.79 1525 1325 10252.80 - 2.99 1525 1425 10253.00 - 3.49 1525 1525 11253.50 - 3.99 1525 1525 12254.00 - 4.49 1525 1525 13254.50 - 4.99 1525 1525 1425


1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

6 7224, 7524

Ho

t R

olle

d P

rod

uct

s

93


www.erdemir.com.tr

Ava

ilab

le S

izes

Notes1- The minimum width is 700 mm.2- The maximum thickness to be ordered for grades 3938, 3940, 3945, 3946, 6837, 6842, 6847, 6852 is 5.00 mm.3- The maximum thickness to be ordered for grades 3330, 3333, 3336, 3340, 3345, 3350, 6035 is 6.00 mm.4- The order limits of thickness for grades 7224, 7524 are min. 2.60 mm and max. 6.00 mm.5- The minimum thickness to be ordered for grades 3430, 3433, 3436, 3440, 6036, 6222, 6223, 6224, 6624, 7222 is 6.01 mm.6- Orders for grades 6222, 6223, 6224, 6624, 7222 of products 6 mm and under in thickness are subject to negotiation.7- Order for small coil is not accepted for the product of thickness greater than 7.51 mm.

RP Hot rolled, pickled coil with trimmed edge

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 5 Group 61.50 - 1.79 1100 10001.80 - 1.99 1200 11002.00 - 2.09 1200 1200 1000 900 9002.10 - 2.29 1300 1200 1000 900 9002.30 - 2.49 1400 1200 1100 1000 10002.50 - 2.79 1500 1300 1200 1100 1100 10002.80 - 2.99 1500 1400 1300 1200 1200 10003.00 - 3.19 1500 1500 1400 1300 1200 11003.20 - 3.49 1500 1500 1400 1300 1300 11003.50 - 3.59 1500 1500 1500 1400 1300 12003.60 - 3.99 1500 1500 1500 1400 1400 12004.00 - 4.49 1500 1500 1500 1500 1500 13004.50 - 4.99 1500 1500 1500 1500 1500 14005.00 - 8.00 1500 1500 1500 1500 1500 1500


1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 3433, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3436, 3440, 3701, 3702, 3940, 3944, 4044, 4244, 6018, 6035, 6036, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

4 3945, 3946, 6847, 6852, 9035, 9052, 9255, 9256, 99605 800, 801, 810, 811, 812, 3955, 4932, 4936

6

735, 820, 835, 3030, 3250, 3260, 3350, 3660, 3732, 3736, 3949, 3957, 3960, 4732,4736, 4942, 4946, 4950, 5035, 5040, 5045, 5050, 5246, 5360, 5620, 5630, 6050,6052, 6252, 6284, 6345, 6347, 6352, 6353, 6355, 6704, 6850, 6855, 6860, 6865, 6870,7224, 7524, 9257, 9335, 9338, 9342, 9355, 9356, 9435, 9442, 9449, 9455, 9460, 9500

Ho

t R

olle

d P

rod

uct

s

94

Notes1- The minimum width is 700 mm.2- Orders for products in range of 1511-1530 mm in width are subject to negotiation for products with minimum thickness of 7 mm.3- The maximum thickness to be ordered for grades 3938, 3940, 3945, 3946, 6837, 6842, 6847, 6852 is 5.00 mm.4- The maximum thickness to be ordered for grades 720, 835, 3337, 3660, 4044 is 8.00 mm.5- The maximum thickness to be ordered for grades 3330, 3333, 3336, 3340, 3345, 3350, 6035 is 6.00 mm.6- The maximum thickness to be ordered for grades 9035, 9052, 9255, 9256, 9960 is 10.00 mm.7- The maximum thickness to be ordered for the grades of Group-6 except for grades 7224, 7524 is 10.00 mm.8- The order limits of thickness for grades 7224, 7524 are min. 2.60 mm and max. 6.00 mm.9- The minimum thickness to be ordered for grades 3430, 3433, 3436, 3440, 6036, 6222, 6223, 6224, 6624, 7222 is 6.01 mm.10- Orders for grades 6222, 6223, 6224, 6624, 7222 of products 6 mm and under in thickness are subject to negotiation.11- Order for small coil is not accepted for the product of thickness greater than 7.51 mm.

RPKK Hot rolled, pickled coil with mill edge

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 5 Group 61.50 - 1.79 1125 10251.80 - 1.99 1225 11252.00 - 2.09 1225 1225 1025 925 9302.10 - 2.29 1325 1225 1025 925 9302.30 - 2.49 1425 1225 1125 1025 10302.50 - 2.79 1525 1325 1225 1125 1130 10252.80 - 2.99 1525 1425 1325 1225 1230 10253.00 - 3.19 1525 1525 1425 1325 1230 11253.20 - 3.49 1525 1525 1425 1325 1330 11253.50 - 3.59 1525 1525 1525 1425 1330 12253.60 - 3.99 1525 1525 1525 1425 1430 12254.00 - 4.49 1525 1525 1525 1525 1530 13254.50 - 4.99 1525 1525 1525 1525 1530 14255.00 - 6.99 1525 1525 1525 1525 1530 15257.00-16.00 1510 1510 1510 1510 1510 1510


1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 34333936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3436, 3440, 3701, 3702, 3940, 3944, 4044, 4244, 60186035, 6036, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

4 3945, 3946, 6847, 6852, 9035, 9052, 9255, 9256, 99605 800, 801, 810, 811, 812, 3955, 4932, 4936

735, 820, 835, 3030, 3250, 3252 3260, 3350, 3660, 3732, 3736, 3949, 3957, 3960, 4732, 4736,

64942, 4946, 4950, 5035, 5040, 5045, 5050, 5060, 5070, 5080, 5246, 5270, 5360, 5620, 5630,6050, 6052, 6252, 6284, 6345, 6347, 6352, 6353, 6355, 6704, 6850, 6855, 6860, 6865, 6870,7224, 7524, 9257, 9280, 9335, 9338, 9342, 9355, 9356, 9435, 9442, 9449, 9455, 9460, 9500

Ho

t R

olle

d P

rod

uct

s

95


www.erdemir.com.tr

Ava

ilab

le S

izes

Notes1- The minimum width is 700 mm.

TRP Hot rolled, skin-passed, pickled coil with trimmed edge

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 5 Group 61.50 - 1.79 1100 10001.80 - 1.99 1200 11002.00 - 2.09 1200 1200 10002.10 - 2.29 1300 1200 10002.30 - 2.49 1400 1200 11002.50 - 2.59 1500 1300 12002.60 - 2.79 1500 1300 1200 10002.80 - 2.99 1500 1400 1300 10003.00 - 3.49 1500 1500 1400 11003.50 - 3.99 1500 1500 1500 12004.00 - 4.49 1500 1500 1500 13004.50 - 4.99 1500 1500 1500 14005.00 - 5.00 1500 1500 1500 1500


1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3701, 3702, 3940, 3944, 4044, 4244, 6018, 6035, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

6 7224, 7524

Ho

t R

olle

d P

rod

uct

s

96

Notes1- The minimum width is 700 mm.2- The maximum thickness to be ordered for grades 3938, 3940, 6837, 6842 is 5.00 mm.3- The maximum thickness to be ordered for grades 3330, 3333, 3336, 3340, 3345, 6035 is 6.00 mm.4- The minimum thickness to be ordered for grades 3430, 3433, 3436, 3440, 6036 is 6.01 mm.

TRPKK Hot rolled, skin-passed, pickled coil with mill edge

Dimensions




1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 3433, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3436, 3440, 3701, 3702, 3940, 3944, 4044, 4244, 6018, 6035, 6036, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

6 7224, 7524

Ho

t R

olle

d P

rod

uct

s

97


www.erdemir.com.tr

Ava

ilab

le S

izes

Notes1- The minimum width is 700 mm.2- The maximum thickness to be ordered for grades 3938, 3940, 3945, 3946, 6837, 6842, 6847, 6852 is 5.00 mm.3- The maximum thickness to be ordered for grades 3330, 3333, 3336, 3340, 3345, 3350, 6035, 7224, 7524 is 6.00 mm.4- The maximum thickness to be ordered for grades 720, 835, 3337, 3660, 4044 is 8.00 mm.5- The maximum thickness to be ordered for grades 9035, 9052, 9255, 9256, 9960 is 10.00 mm.6- The maximum thickness to be ordered for the grades of Group-6 except for grades 7224, 7524 is 10.00 mm.7- The minimum thickness to be ordered for grades 3430, 3433, 3436, 3440, 6036, 6222, 6223, 6224, 6624, 7222 is 6.01 mm.8- Orders for grades 6222, 6223, 6224, 6624, 7222 of products 6 mm and under in thickness are subject to negotiation.9- Length: min. 1500 mm, max. 12000 mm.10- a) For the nominal length < = 4000 mm, maximum bundle weight is 7 t.


LP Hot rolled, pickled plate cut from coil with trimmed edge

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 5 Group 65.00 - 15.00 1500 1500 1500 1500 1500 1500


1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 3433, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3436, 3440, 3701, 3702, 3940, 3944, 4044, 4244, 60186035, 6036, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

4 3945, 3946, 6847, 6852, 9035, 9052, 9255, 9256, 99605 800, 801, 810, 811, 812, 3955, 4932, 4936

735, 820, 835, 3030, 3250, 3260, 3350, 3660, 3732, 3736, 3949, 3957, 3960,

64732, 4736, 4942, 4946, 4950, 5035, 5040, 5045, 5246, 5620, 5630, 6050, 6052,6252, 6284, 6345, 6347, 6352, 6353, 6355, 6704, 6850, 6855, 6860, 6865, 6870, 7224, 7524, 9257, 9335, 9338, 9342, 9355, 9356, 9435, 9442, 9449, 9455, 9460

Ho

t R

olle

d P

rod

uct

s

98

Notes1- The minimum width is 700 mm.2- Orders for products in range of 1511-1530 mm in width are subject to negotiation for products with minimum thickness of 7 mm.3- The maximum thickness to be ordered for grades 3938, 3940, 3945, 3946, 6837, 6842, 6847, 6852 is 5.00 mm.4- The maximum thickness to be ordered for grades 3330, 3333, 3336, 3340, 3345, 3350, 6035, 7224, 7524 is 6.00 mm.5- The maximum thickness to be ordered for grades 720, 835, 3337, 3660, 4044 is 8.00 mm.6- The maximum thickness to be ordered for grades 9035, 9052, 9255, 9256, 9960 is 10.00 mm.7- The maximum thickness to be ordered for the grades of Group-6 except for grades 7224, 7524 is 10.00 mm.8- The minimum thickness to be ordered for grades 3430, 3433, 3436, 3440, 6036, 6222, 6223, 6224, 6624, 7222 is 6.01 mm.9- Orders for grades 6222, 6223, 6224, 6624, 7222 of products 6 mm and under in thickness are subject to negotiation10- Length: min. 1500 mm, max. 12000 mm.11- a) For the nominal length ≤ 4000 mm, maximum bundle weight is 7 t.


LPKK Hot rolled, pickled plate cut from coil with mill edge

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 5 Group 65.00 - 6.99 1525 1525 1525 1525 1530 15257.00 - 15.00 1510 1510 1510 1510 1510 1510


1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 3433, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3436, 3440, 3701, 3702, 3940, 3944, 4044, 4244, 60186035, 6036, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

4 3945, 3946, 6847, 6852, 9035, 9052, 9255, 9256, 99605 800, 801, 810, 811, 812, 3955, 4932, 4936

735, 820, 835, 3030, 3250, 3260, 3350, 3660, 3732, 3736, 3949, 3957, 3960,

64732, 4736, 4942, 4946, 4950, 5035, 5040, 5045, 5246, 5620, 5630, 6050, 6052, 6252, 6284, 6345, 6347, 6352, 6353, 6355, 6704, 6850, 6855, 6860, 6865, 6870, 7224, 7524, 9257, 9335, 9338, 9342, 9355, 9356, 9435, 9442, 9449, 9455, 9460

Ho

t R

olle

d P

rod

uct

s

99


www.erdemir.com.tr

Notes1- The minimum width is 700 mm.2- Maximum width to be ordered for product type TLP is 1500 mm.3- The maximum thickness to be ordered for grade 3938, 6837 is 5.00 mm.4- The maximum thickness to be ordered for grades 3330, 3333, 7224, 7524 is 6.00 mm.5- The minimum thickness to be ordered for grades 3430, 3433 is 6.01 mm.6- Length: min. 1500 mm, max. 12000 mm.7- a) For the nominal length ≤ 4000 mm, maximum bundle weight is 7 t.


Ava

ilab

le S

izesTLP Hot rolled, skin-passed and pickled sheet cut from coil with trimmed edge

TLPKK Hot rolled, skin-passed and pickled sheet cut from coil with mill edge

Dimensions


Group 1 Group 2 Group 3 Group 4 Group 5 Group 65.00 - 6.50 1525 1525 1525


1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 3433, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

6 7224, 7524

Ho

t R

olle

d P

rod

uct

s

100

Notes1- The maximum thickness for the grades 3938, 3940, 3945, 3946, 6837, 6842, 6847, 6852 is 5.00 mm.2- The maximum thickness to be ordered for grades 3330, 3333, 3336, 3340, 3345, 6035 is 6.00 mm.3- The limits of thickness to be ordered for the grades 7224, 7524 are min. 2.60 mm and max. 6.00 mm.4- The minimum thickness to be ordered for grades 3430, 3433, 3436, 3440, 6036, 6222, 6223, 6224, 6624, 7222 is 6.01 mm.5- Orders for grades 6222, 6223, 6224, 6624, 7222 of products 6 mm and under in thickness are subject to negotiation.6- No limitation for the weight of slit strip.7- In case of grades of Group-3 ;

Maximum widths of the slit strips in thickness range of 2.00 - 2.29 mm for each number of slit strip on the table above are 500, 333, 250, 200, 143, 111, 91, 77 mm respectively.

8- In case of grades of Group-4 and Group-5 ;Maximum widths of the slit strips in thickness range of 2.00 - 2.29 mm for each number of slit strip on the table above are 450, 300, 225, 180, 128, 100, 82, 69 mm respectively.

9- In case of grades of Group-4 and Group-5 ;Maximum widths of the slit strips in thickness range of 2.30 - 2.49 mm for each number of slit strip on the table above are 500, 333, 250, 200, 143, 111, 91, 77 mm respectively

9- In case of grades of Group-6 ;Maximum widths of the slit strips in thickness range of 2.60 - 2.99 mm for each number of slit strip on the table above are 500, 333, 250, 200, 143, 111, 91, 77 mm respectively.

RD Hot rolled, slitted coil

RPD Hot rolled, pickled, slitted coil

Dimensions Groups-1, 2, 3, 4, 5, 6

Thickness (mm)Strip width within slit coil according to number of slits (mm)2 3 4 5 7 9 11 13

2.00 - 2.50 400 - 533 267 - 355 200 - 266 160 - 213 115 - 152 89 - 118 73 - 97 62 - 822.51 - 3.00 400 - 533 267 - 355 200 - 266 160 - 213 115 - 152 89 - 118 73 - 973.01 - 3.50 400 - 533 267 - 355 200 - 266 160 - 213 115 - 152 89 - 1183.51 - 4.00 400 - 533 267 - 355 200 - 266 160 - 213 115 - 1524.01 - 4.50 400 - 533 267 - 355 200 - 266 160 - 2134.51 - 5.00 400 - 533 267 - 355 200 - 2665.01 - 6.00 400 - 533 267 - 3556.01 - 6.35 400 - 533


1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 3433, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3436, 3440, 3701, 3702, 3940, 3944, 4044, 4244, 6018, 6035, 6036, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329

4 3945, 3946, 6847, 6852, 9035, 9052, 9255, 9256, 99605 800, 801, 810, 811, 812, 3955, 4932, 49366 7224, 7524

Ho

t R

olle

d P

rod

uct

s

101


www.erdemir.com.tr

Ava

ilab

le S

izes

Notes1- The maximum thickness for the grade 3938, 6837 is 5.00 mm.2- The maximum thickness to be ordered for grades 3330, 3333 is 6.00 mm.3- The limits of thickness to be ordered for the grades 7224, 7524 are min. 2.60 mm and max. 6.00 mm.4- The minimum thickness to be ordered for grades 3430, 3433 is 6.01 mm.5- No limitation for the weight of slit strip.6- In case of grades of Group-6;

Maximum widths of the slit strips in thickness range of 2.60 - 2.99 mm for each number of slit strip on the table above are 500, 333, 250, 200, 143, 111, 91, 77 mm respectively.

TRPD Hot rolled, skin-passed, pickled, slitted coil

Dimensions Groups-1, 2, 6

Thickness (mm)Strip width within slit coil according to number of slits (mm)

2 3 4 5 7 9 11 132.00 - 2.50 400 - 533 267 - 355 200 - 266 160 - 213 115 - 152 89 - 118 73 - 97 62 - 822.51 - 3.00 400 - 533 267 - 355 200 - 266 160 - 213 115 - 152 89 - 118 73 - 973.01 - 3.50 400 - 533 267 - 355 200 - 266 160 - 213 115 - 152 89 - 1183.51 - 4.00 400 - 533 267 - 355 200 - 266 160 - 213 115 - 1524.01 - 4.50 400 - 533 267 - 355 200 - 266 160 - 2134.51 - 5.00 400 - 533 267 - 355 200 - 2665.01 - 6.00 400 - 533 267 - 3556.01 - 6.35 400 - 533


1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 3433, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

6 7224, 7524

Ho

t R

olle

d P

rod

uct

s

102

Notes1- Orders for the grades 5060, 5070, 5080, 5270, 5360, 8416, 9280 are not accepted in case of LR.2- Orders for products in range of 1511-1525 mm in width are subject to negotiation for products with minimum thiknes of 7 mm.3- For product type LR, maximum width to be ordered is 1500 mm.4- Length: min. 2000 mm, max. 15000 mm.5- a) For the nominal length ≤ 4000 mm, maximum bundle weight is 7 t.

b) For the nominal length > 4000 mm, no limitation for bundle weight.6- The maximum thickness to be ordered for grades 3938, 3940, 3945, 3946, 6837, 6842, 6847, 6852 is 5.00 mm.7- The maximum thickness to be ordered for grades 3330, 3333, 3336, 3340, 3345, 3350, 6035, 7224, 7524 is 6.00 mm.8- The maximum thickness to be ordered for grades 720, 835, 3337, 3660, 4044 is 8.00 mm.9- The minimum thickness to be ordered for grades 3430, 3433, 3436, 3440, 6036 is 6.01 mm.10- The minimum thickness to be ordered for grades 5732, 5736, 6705, 6732, 6736, 8434 is 8.00 mm11- For grades 9060, 9065, 9070 of products with maximum width of 1200 mm, orders for products thinner than 7 mm in thickness are subject to negotiation.12- An order is not made for grades 9060, 9065, 9070 of products both larger than 1200 mm in width and thinner than 7 mm in thickness.13- Request for normalizing is accepted for the conditions given below:

a) The minimum thickness of the product shall be 8 mm.b) The length of product shall be min. 4000 mm and max. 12000 mm.c) Orders for grades 735, 4732, 4736, 5246, 5732, 5736, 6335, 6341, 6345, 6347, 6352, 6353, 6355, 6704, 6705, 6732, 6736, 6850, 6855, 6860, 6865, 6870, 9355, 9356 of products of 8 mm or over in thickness are accepted on condition that the normalizing of the products is carried out innormalizing furnace.d) For other grades, request for normalizing is accepted provided that the minimum thickness of the products is 10 mm.

14- In case of minimum thickness of the products is 8 mm, request for ultrasonic test is accepted.

LR Hot rolled plate cut from coil with trimmed edge

LRKK Hot rolled plate cut from coil with mill edge

Dimensions

Thickness (mm)Width (mm)

Group 1 Group 2 Group 3 Group 4 Group 5 Group 65.00 - 6.99 700 - 1525 700 - 1525 700 - 1525 700 - 1525 700 - 1525 700 - 15257.00 - 10.00 700 - 1510 700 - 1510 700 - 1510 700 - 1510 700 - 1510 700 - 151010.01 - 15.00 800 - 1510 800 - 1510 800 - 1510 800 - 1510 800 - 1510 800 - 1510


1 700, 3008, 3922, 3923, 4009, 6006, 6222, 6223, 6224, 6282, 6523, 6624, 7222

2720, 2008, 2009, 3010, 3012, 3015, 3018, 3237, 3281, 3330, 3333, 3337, 3430, 3433, 3936, 3937, 3938, 4237, 4437, 5437, 6037, 6837, 9030

33020, 3241, 3244, 3336, 3340, 3345, 3436, 3440, 3701, 3702, 3940, 3944, 4044, 4244, 6018, 6040, 6044, 6237, 6244, 6335, 6341, 6741, 6838, 6842, 9042, 9046, 9056, 9240, 9329, 6035, 6036

4 3945, 3946, 6847, 6852, 9035, 9052, 9060, 9255, 9256, 99605 800, 801, 810, 811, 812, 3955, 4932, 4936

6

735, 820, 835, 3030, 3250, 3252, 3260, 3350, 3660, 3732, 3736, 3949, 3957, 3960, 4732, 4736, 4942, 4946, 4950, 5035, 5040, 5045, 5050, 5060, 5070, 5080, 5246, 5270, 5360, 5620, 5630, 5732, 5736, 6050, 6052,6252, 6284, 6345, 6347, 6352, 6353, 6355, 6704, 6705, 6732, 6736, 6850, 6855, 6860, 6865, 6870, 7224, 7524, 8416, 8434, 9065, 9070, 9257, 9280, 9335, 9338, 9342, 9355, 9356, 9435, 9442, 9449, 9455, 9460, 9500

Ho

t R

olle

d P

rod

uct

s

103


www.erdemir.com.tr

Ava

ilab

le S

izes

GradesGroup Code GradesA 3008, 3010, 3012, 3015, 3018, 3020, 3030, 3237, 3241, 3244, 3250, 3252, 3260, 5035, 3701,3702,3732,

3736, 4732, 4736, 5732, 5736, 5040, 5045, 5050, 5060, 5070, 5080, 5246, 5270, 5345, 5360, 5620, 5630, 6006, 6018, 6222, 6224, 6237, 6244, 6252, 6284, 6355, 6624, 6704, 6705, 6732, 6736, 6741, 6855, 6860, 6865, 6870, 7224, 8412, 8414, 8416, 8430, 8434, 8440, 8613, 9329, 9335, 9338, 9342, 9355, 9356, 9960

B 6037, 6044, 6050, 6052, 6335, 6341, 6345, 6347, 6352, 6353, 6838, 6850, 9435, 9442C 6036, 9449D 9455, 9500

Maximum lengths of plates wider than 1500 mm

Thickness (mm)Length (mm)

Group-A Group-B Group-C Group-D12.00 - 15.99 12000 12000 12000 1200016.00 - 20.00 12000 12000 12000 1200020.01 - 22.00 10000 10000 1000022.01 - 25.00 9500 9500 950025.01 - 28.00 9000 900028.01 - 30.00 8500 850030.01 - 35.00 7000 700035.01 - 40.00 6500 650040.01 - 45.00 5500 550045.01 - 50.00 5000 500050.01 - 55.00 450055.01 - 60.00 4000

L Heavy plate with trimmed edgeLKK Heavy plate with mill edge

Dimensions

Thickness (mm)Width (mm)

Group-A Group-B Group-C Group-D12.00 - 15.99 1511- 2600 1511 - 2600 1511 - 2600 1511 - 260016.00 - 20.00 1000 - 2600 1000 - 2600 1000 - 2600 1000 - 260020.01 - 25.00 1000 - 2600 1000 - 2600 1000 - 260025.01 - 50.00 1000 - 2600 1000 - 260050.01 - 60.00 1000 - 2600

Ho

t R

olle

d P

rod

uct

s

104

Notes1- Thicknesses of 25 mm and above are not accepted in case of product type L.2- Orders for the grades 3260, 5040, 5045, 5050, 5060, 5070, 5080, 5270, 5345, 5360, 5630, 8412, 8414, 8416, 8430, 8434, 8440, 8613

are not accepted in case of product type L.3- The maximum thickness to be ordered for grade 9442 is 40.00 mm.4- The nominal lengths are min. 2000 mm and max. 12000 mm provided that the lengths of 4000 mm under are subject to negotiation. 5- Orders for the grades 4732, 4736, 5246, 5732, 5736, 6037, 6044, 6050, 6052, 6237, 6244, 6252, 6284, 6335, 6341, 6345, 6347, 6352, 6353, 6355,

6704, 6705, 6732, 6736, 6850, 6855, 6860, 6865, 6870, 9355, 9356 are accepted provided that the normalizing of the products is carried out in nomalizing furnace.

6- For grades 6052, 6237, 6244, 6252, 6284, order thicknesses greater than 25 mm are acceptedprovided that the normalizing of the products is carried out.

7- The lengths of the products to be normalized are min. 4000 mm and max. 12000 mm.8- For products to be normalized, plate weight is max. 7 t.9- The request for ultrasonic test is accepted.

Ho

t R

olle

d P

rod

uct

s

105


www.erdemir.com.tr

Ava

ilab

le S

izes

Maximum Length (mm)

Thickness (mm) Maximum Length (mm)

Notes1- Orders for the grades other than grades in the table above are subject to negotiation.2- The minimum nominal length is 2000 mm provided that the lengths of 4000 mm under are subject to negotiation.3- Properties other than chemical composition and dimensions (mechanical properties, internal soundness) are not guaranteed.4- Request for normalizing is not accepted.5- Request for ultrasonic test is not accepted.6- DIN EN 10163 Class A Subclass 3 is applied for surface defects.

DS Casted slab (extra heavy plate with mill edge)

DimensionsThickness (mm) Width (mm)61.00 - 200.00 1000 - 1510


1 3008 ,3010 ,3012 ,3015 ,3020 ,3030, 3995, 5035, 5040, 5045, 6006 , 6018, 6224

61.00 - 80.99 1200081.00 - 90.99 1100091.00 - 100.99 10000101.00 - 110.99 9000111.00 - 130.99 8000131.00 - 150.99 7000151.00 - 200.00 6000

Ho

t R

olle

d P

rod

uct

s

106

Group Erdemir Steel Grades Incerement in tolerances on thickness

ASteels with normal deformation resistance at elevated temperatures

-(Steel grades other than categories of B, C, D)735, 810, 811, 812, 1835, 3250, 3252, 3260, 3736, 3949, 3955 4736, 4936, 5035, 5040, 5045, 5050, 5246, 5270, 5620, 5630

15%B5736, 6050, 6052, 6252, 6284, 6347, 6352, 6353, 6355, 6736 6847, 6850, 6852, 8416, 8440, 8613, 9052, 9355, 9356, 9960

C820, 3660, 3957, 4942, 4946, 5060, 5345, 5360

30%8414, 8430, 8434, 9056, 9060, 9065, 9255, 9256, 9338, 9342, 9442

D835, 3960, 4950, 5070, 5080, 8412, 9070, 9257, 9280, 9449 9455, 9460, 9500

40%

DIN EN 10051 - 1997Symbols Of Products Covered By This Standard: R, RKK, BRKK, KRKK, RP, RPKK, HCKK, BCKK, TCKK, RD, RPD, TRPD,TR, TRKK, TRP, TRPKK, TLP, TLPKK, THRP, THRPK, HRU, THRU, HRUKK, HRP, HRPKK, LP, LPKK, LR, LRKK

The specified values for tolerances shall not apply to the uncropped ends of the coil for a total length which is calculatedusing the formula: “ Length (meters) = 90 / thickness (mm)” provided that the result does not exceed 20 meters.

Notes1- The thickness shall be measured at any point situated at least 40 mm from the edges for products with mill edge.2- The thickness shall be measured at any point situated at least 25 mm from the edges for products with trimmed edge.

Tolerances

Thickness Tolerance For Steel Products with (Yield Strength (Re), Width (w) and Thickness)

1. 700, 1718, 1722, 1726, 3922, 3923, 6006, 6222, 6223, 6224, 6282, 6314, 6315, 6406, 6412, 6413, 6422, 6423, 6424, 6426, 6523, 6624, 7222, 7224, 7414, 7416, 7524 the following tolerances apply:

Thickness (mm) ≤1200 1200<w≤1500 1500<w≤15251.50 - 2.00 ± 0.13 ± 0.14 ± 0.162.01 - 2.50 ± 0.14 ± 0.16 ± 0.172.51 - 3.00 ± 0.15 ± 0.17 ± 0.183.01 - 4.00 ± 0.17 ± 0.18 ± 0.204.01 - 5.00 ± 0.18 ± 0.20 ± 0.215.01 - 6.00 ± 0.20 ± 0.21 ± 0.226.01 - 8.00 ± 0.22 ± 0.23 ± 0.23

2. The thickness tolerances for steels (Category A) with normal deformation resistance at elevated temperatures are as follows

Thickness (mm) ≤1200 1200<w≤1500 1500<w≤15251.50 - 2.00 ± 0.17 ± 0.19 ± 0.212.01 - 2.50 ± 0.18 ± 0.21 ± 0.232.51 - 3.00 ± 0.20 ± 0.22 ± 0.243.01 - 4.00 ± 0.22 ± 0.24 ± 0.264.01 - 5.00 ± 0.24 ± 0.26 ± 0.285.01 - 6.00 ± 0.26 ± 0.28 ± 0.296.01 - 8.00 ± 0.29 ± 0.30 ± 0.318.01 - 10.00 ± 0.32 ± 0.33 ± 0.3410.01 - 12.50 ± 0.35 ± 0.36 ± 0.3712.51 - 15.00 ± 0.37 ± 0.38 ± 0.4015.01 - 25.00 ± 0.40 ± 0.42 ± 0.45

Ho

t R

olle

d P

rod

uct

s

107www.erdemir.com.tr

To

lera

nce

s


Tolerances On Length Length (mm) Lower Upper1999 and less 0 + 102000 - 7999 0 + 0,005Xlength8000 and more 0 + 40

Notes1- The product length shall be considered to be the length of the largest rectangle included in the sheet or plate.

Flatness Tolerance Thickness (mm) Flatness Tolerances For Grades Of Category A

Width (mm)≤1200 1200<w≤1500 >1500

1.50 - 2.00 18 20 252.01 - 25.00 15 18 23

Thickness (mm) ≤ 25.00 Flatness Tolerances For Grades Of Categories B, C, DWidth (mm)

≤1200 1200<w≤1500 >1500B 18 23 28C 23 30 38D 28 37 48

Length Tolerance

Notes1- Deviation from flatness shall be determined by measuring the deviation in distance between the product and a flat horizontal surface on

which it is placed. 2- Values for deviation from flatness are guaranteed for the products which are cut to length in Erdemir.

Notes1- Tolerances for trimmed edge apply to products with nominal thicknesses <= 10 mm.2- For nominal thickness > 10 mm, the upper tolerances are increased by 1 mm.3- The width shall be measured at right angles to the longitudinal axis of the product.

Width ToleranceProducts With Trimmed Edge Products With Mill Edge

Width (mm) Lower Upper Lower Upper1200 and narrow 0 + 3 0 + 201201 - 1499 0 + 5 0 + 201500 and wide 0 + 6 0 + 25

Distance

Flat Horizontal Surface

Ho

t R

olle

d P

rod

uct

s

108

a: Min. distance from the end of sheet / plate for normal flatness tolerances (200 mm)

b: Min. distance from the longitudinal edges of sheet / plate for normal flatness tolerances (25 mm)

q: Edge camber

u: Out-of-squareness

Notes1- The out-of-squareness “u” is the orthogonal projection of a transverse edge over a longitudinal edge.2- The out-of-squareness “u” shall not exceed 1 % of the actual width of the product.

Tolerances For Out-Of-Squareness

Deviation

Area for FlatnessMeasurements

DIN EN 10051 - 1997

Ho

t R

olle

d P

rod

uct

s


To

lera

nce

s


Notes1- The difference in thickness within one coil shall be measured at a line with a invariable distance (40 mm) from the longitudinal edges.2- These tolerances apply to hot rolled products for cold rolling (HCKK, BCKK, TCKK).

Notes1- The edge camber is the maximum deviation of a longitudinal edge from a straight edge measuring base applied to it.2- The edge camber shall be measured on the concave side of the product.3- The edge camber shall not exceed 0.5 % of the actual length of the sheet/plate for a nominal length smaller than 5000 mm.

Tolerances For Edge CamberDimensions Tolerances (mm)

Type of Product Width (mm) Length (mm) Gauge Length (mm) Mill edge Trimmed edge

Sheet - Plate≥ 600 ≥ 5000 5000 20 15≥ 600 < 5000 Actual Length (L) + 0.005 x L + 0.005 x L

Coil ≥ 600 - 5000 20 15Slitted Coil ≤ 600 - 2500 10 10

Permissible Difference In Thickness Within One Coil

Thickness (mm) Width (mm)

≤1200 1200<w ≤1500 1500<w ≤15251.50 - 2.00 0.20 0.24 0.282.01 - 3.00 0.22 0.27 0.333.01 - 4.00 0.28 0.32 0.404.01 - 8.00 0.28 0.32 0.40

Distance Distance

Notes1- The standard DIN 1016 - 1987 is applied to deviations from form of coils.2- The coils shall be tightly wound, as round as possible and straight - edged. Gradually stepped displacement of the edges of the coils to one

side shall not exceed the deviations given in table.

Notes1- The standard DIN 1016 - 1987 is applied to deviations from inside diameter of coil.

Ho

t R

olle

d P

rod

uct

s

110

Permissible CrownWidth (mm) Tolerances(mm)1200 and narrow 0 - 0.101201 - 1500 0 - 0.131501 - 1525 0 - 0.16

Notes1- The crown shall be measured as the thickness difference between the center line of the product and a measuring point at 40 mm from any

edge of the product.2- These tolerances apply to hot rolled products for cold rolling (HCKK, BCKK, TCKK).

Permissible Deviations From Inside Diameter Of CoilDeviation (%)

Type of Product Width (mm) Mill Edge Trimmed EdgeCoil ≥ 600 ± 7% ± 3%Slitted Coil < 600 ± 7% ± 3%

Permissible Deviations From Form Of Coils (Telescopy)Tolerances (mm)

Type of Product Width (mm) Mill Edge Trimmed EdgeCoil ≥ 600 + 60 + 40Slitted Coil < 600 + 35 + 25

DIN EN 10051 - 1997

Ho

t R

olle

d P

rod

uct

s


To

lera

nce

s


Notes1- The length of the plate is the length of the largest rectangle contained within the plate.

DIN EN 10029 - 1991Symbols Of Products Covered By This Standard: L, LKK

Notes1- The thickness shall be measured at any point situated at least 25 mm from the edges for plates with trimmed edge.2- The thickness shall be measured at any point situated at least 40 mm from the edges for plates with mill edge.

Thickness Tolerance Maximum Thickness Difference Within a Plate

Thickness (mm) Tolerances (mm) Width (mm)Lower Upper 1000≤ w<2000 2000≤w <2500 2500≤ w<3000 3000≤ w<3500 3500≤ w<4000

5.00 - 7.99 - 0.4 + 1.1 0.9 0.9 1.0 1.0 -8.00 - 14.99 - 0.5 + 1.2 0.9 1.0 1.0 1.1 1.115.00 - 24.99 - 0.6 + 1.3 1.0 1.1 1.2 1.2 1.325.00 - 39.99 - 0.8 + 1.4 1.1 1.2 1.2 1.3 1.340.00 - 79.99 - 1.0 + 1.8 1.2 1.3 1.4 1.4 1.580.00 - 149.99 - 1.0 + 2.2 1.3 1.4 1.5 1.5 1.6150.00 - 250.00 - 1.2 + 2.4 1.4 1.5 1.6 1.6 1.7

Notes1- The width shall be measured perpendicular to the major axis of the plate.

Width Tolerance Plates With Trimmed Edge

Width(mm) Lower Upper1000 - 1999 0 + 202000 - 2999 0 + 253000 and wide 0 + 30

Plates With Mill EdgeWidth(mm) Lower Upper801 - 1000 0 + 301001 - 1500 0 + 381501 - 3000 0 + 503001 - 4000 0 + 60

Length TolerancesLength (mm) Lower Upper2000 - 3999 0 + 204000 - 5999 0 + 306000 - 7999 0 + 408000 - 9999 0 + 5010000 - 14999 0 + 7515000 - 20000 0 + 100

Ho

t R

olle

d P

rod

uct

s

112

Notes1- If the distance between the points of contact of the straightedge and the plate is less than 1000 mm, the permissible deviation from flatness

shall comply with the following requirements: For steel type L, max. 1 % or for steel type H, max. 1.5 % of the distance between points of contact on the plate between 300 mm to 1000 mm, but not exceeding the values given in table above.

2- Deviation from flatness shall be determined by measuring the deviation in distance between the plate and a flat horizontal surface on which it is placed.

3- Deviations from flatness shall be measured at a point at least 25 mm from the longitudinal edges and at a distance at least 200 mm from theplate ends.

Notes1- t: Tonne2- w: Nominal width (mm)3- The excess mass is the difference between the actual delivered mass and the theoretical mass, expressed as a percentage of the

theoretical mass of the delivery.4- The theoretical mass shall be determined using a volumetric mass of 7.85 kg/dm3.

Flatness ToleranceNormal Tolerances For Gauge Lengths Specified (mm)

Thickness (mm) Steel Type L Steel Type HProducts with a specified minimum Products with a specified minimum

yield strength ≤ 460 N/mm2, neither quenched nor yield strength > 460 N/mm2 and < 700 N/mm2

quenched and tempered products and all grades of quenched and quenched and tempered products1000 mm 2000 mm 1000 mm 2000 mm

5.00 - 7.99 8 12 11 158.00 - 14.99 7 11 10 1415.00 - 24.99 7 10 10 1325.00 - 39.99 6 9 9 1240.00 - 250.00 5 8 8 11

Mass ToleranceThickness Excess Masses Adjusted in Relation To The Lot Mass (%)

Thickness (mm)Tolerances (mm) 1000≤w <2000 2000≤ w<2500 2500≤ w<3000 3000≤w <3500 3500≤w

Lot Mass Lot Mass Lot Mass Lot Mass Lot Mass

Lower Upper <10t 10t-24t 25t-74t <10t 10t-24t 25t-74t <10t 10t-24t 25t-74t <10t 10t-24t 25t-74t <10t 10t-24t 25t-74t

5.00 - 7.99 - 0,4 + 1.1 9.8 8.4 7.0 10.5 9.0 7.5 11.9 10.2 8.5 12.6 10.8 9.0

8.00 - 14.99 - 0,5 + 1.2 8.4 7.2 6.0 8.4 7.2 6.0 9.1 7.8 6.5 9.8 8.4 7.0 10.5 9.0 7.5

15.00 - 24.99 - 0,6 + 1.3 6.3 5.4 4.5 6.3 5.4 4.5 7.0 6.0 5.0 7.0 6.0 5.0 7.7 6.6 5.5

25.00 - 39.99 - 0,8 + 1.4 4.9 4.2 3.5 4.9 4.2 3.5 5.6 4.8 4.0 5.6 4.8 4.0 5.6 4.8 4.0

40.00 - 79.99 - 1,0 + 1.8 4.9 4.2 3.5 4.9 4.2 3.5 5.6 4.8 4.0 5.6 4.8 4.0 5.6 4.8 4.0

80.00 - 149.99 - 1,0 + 2.2 4.9 4.2 3.5 4.9 4.2 3.5 5.6 4.8 4.0 5.6 4.8 4.0 5.6 4.8 4.0

150.00 - 249.99 - 1,2 + 2.4 4.9 4.2 3.5 4.9 4.2 3.5 4.9 4.2 3.5 4.9 4.2 3.5 4.9 4.2 3.5

Deviation in Distance


DIN EN 10029 - 1991

Ho

t R

olle

d P

rod

uct

s


To

lera

nce

s


Tolerances For Edge Camber

Notes1- The edge camber value “q” is the maximum deviation between one longitudinal edge and the straight line joining the two ends of this edge.2- The deviation shall be a max. 0.2 % of the actual length of the plate.3- Edge camber is measured on the concave edges of the plate.


a: Min. distance from the end of plate for normal flatness tolerances (200 mm)b: Min. distance from the edge of the plate for normal flatness tolerances (25 mm)q: Edge camberu: Out-of-squareness

Notes1- The out-of-squareness “u” is the orthogonal projection of a transverse edge over a longitudinal edge.2- The out-of-squareness “u” shall not exceed 1 % of the actual width of the plate.

Deviation

Deviation

Area for FlatnessMeasurements

Deviation

Ho

t R

olle

d P

rod

uct

s

114

Erdemir - DS - 2001Symbols Of Products Covered By This Standard: DS

Notes1- The length of the slab is the length of the largest rectangle contained within the slab.

Length ToleranceTolerances (mm)

Length (mm) Lower Upper2000 - 8000 0 + 508001 - 12000 0 + 60

Width Tolerance Tolerances (mm)

Width (mm) Lower Upper1000 - 1525 0 + 50

Notes1- The width shall be measured perpendicular to the major axis of the slab.

Thickness Tolerance Tolerances (mm)

Thickness (mm) Lower Upper61 - 99 - 1.00 + 6.00100 - 200 - 1.00 + 7.00

Notes1- The thickness shall be measured at any point situated at least 40 mm from the edges.

Ho

t R

olle

d P

rod

uct

s


To

lera

nce

s


Notes1- Values for deviation from flatness are guaranteed for the slabs of thicknesses equal to or less than 120 mm.

Notes1- Deviation from flatness shall be determined by measuring the deviation distance between the slab and a flat horizontal surface on which it is

placed.2- If the distance between the points of contact of the straightedge and the slab is less than 1000 mm, the permissible deviation from flatness

shall be max. 1.5% of the distance, but not exceeding the values given in table above.3- Deviations from flatness shall be measured at a point at least 25 mm from the longitudinal edges and at a distance at least 200 mm from the

slab ends.

Flatness ToleranceTolerances For Gauge Lengths Specified (mm)

Length (mm) 1000 mm 2000 mm61.00 - 79.99 8 1180.00 - 99.99 9 12100.00 - 120.00 10 13

Distance


Area for Measuring

Ho

t R

olle

d P

rod

uct

s

116

Notes1- The excess mass is the difference between the actual delivered mass and the theoretical mass, expressed as a percentage of the

theoretical mass of the delivery.


Notes1- No value for tolerance is guaranteed for edge camber of casting slab.


Notes1- No value for tolerance is guaranteed for out-of-squareness of casting slab.

Tolerances On MassThickness (mm) Excess Mass (%)61.00 - 99.99 6.0100.00 - 200.00 6.5

Erdemir - DS - 2001

Ho

t R

olle

d P

rod

uct

s


To

lera

nce

s


Notes1- Patterned plates are supplied with two patterns: Bulb plate (T) and checker plate (R). 2- The patterns shall not be in parallel to the longitudinal edges of the plate.3- Dimensions and tolerances not specified in this standard are subject to agreement.4- Height of pattern: 1 - 2 mm.5- For bulb patterned plate;

Width of pattern: ~ 10 mmLength of pattern: ~ 30 mmDistance of longitudinal axis of two patterns being in parallel: ~ 60 mmDistance of centers of two pattern at right angles: ~ 30 mm

6- For checker plate;Length of long diagonal in pattern : ~ 50 mmLength of short diagonal in pattern: ~ 25 mm

Pattern Tolerance

DIN 59220 - 2000Symbols Of Products Covered By This Standard: MRKK

This standard applies to hot rolled pattern plate having following requirements:Range of thickness: 3 - 10 mmRange of width: 600 - 2000 mmMin. yield strength specified in the standard: max. 355 N/mm2 (36.2 kg/mm2)

Bulb Patterned Checker Patterned

Width Tolerance

Notes1- Deviations from width: - 0, + 20 mm.2- The width shall be measured perpendicular to the major axis of the plate.

Ho

t R

olle

d P

rod

uct

s

118

Notes1- The nominal thicknesses to be preferred are 3, 4, 5, 6, 8, 10 mm.2- The thickness shall be measured at any point situated at least 40 mm from the edges outside the patterned area.

Thickness ToleranceTolerances (mm)

Thickness (mm)Lower Upper

Permissible variation in thickness (mm)

3 - 0.6 + 0.6 0.84 - 0.6 + 0.6 0.85 - 0.75 + 0.75 0.96 - 0.75 + 0.75 0.97 - 0.75 + 0.75 0.98 - 0.85 + 0.85 0.99 - 0.85 + 0.85 0.910 - 0.85 + 0.85 0.9

DIN EN 59220 - 2000

Ho

t R

olle

d P

rod

uct

s


To

lera

nce

s


Notes1- The length of the plate is the length of the largest rectangle contained within the plate

Flatness Tolerance Gauge Length

Thickness (mm) 1000 mm 2000 mm3 9 144 9 145 8 126 8 127 8 128 7 119 7 1110 7 11

a : Min. distance from the end of plate for flatness tolerances (200 mm)

b : Min. distance from the longitudinal edges of plate for flatness tolerances (25 mm)

q : Edge camber

u : Out-of-squareness

Notes1- Deviation from flatness shall be determined by measuring the deviation in distance between the plate and a flat horizontal surface on which

it is placed.

Length Tolerance Length (mm) Max.1500 - 3999 + 204000 - 5999 + 306000 - 7999 + 408000 - 9999 + 5010000 - 14999 + 7515000 + 100

Area for Flatnessmeasurements


Notes1- The edge camber value “q” is the maximum deviation between one longitudinal edge and the straight line joining the two ends of this edge.2- The deviation shall be a max. 0.2 % of the actual length of the plate.3- Edge camber is measured on the concave edges of the plate.

Ho

t R

olle

d P

rod

uct

s

120


Notes1- The out-of-squareness “u” is the orthogonal projection of a transverse edge over a longitudinal edge.2- The out-of-squareness “u” shall not exceed 1 % of the actual width of the plate.

Notes1- The excess mass is the difference between the actual delivered mass and the theoretical mass, expressed as a percentage of the

theoretical mass of the delivery.2- Theoretical mass for bulb patterned plate (T) shall be calculated as follows: [Thickness (mm) x 7.85 kg/dm3] + 2 kg/m2

3- Theoretical mass for checker patterned plate (R) shall be calculated as follows: [Thickness (mm) x 7.85 kg/dm3] + 4 kg/m2

Tolerances On Mass

Thickness (mm)

Theoretical Mass kg/m2 Permissible Positive Deviation From The Theoretical Mass (%)Type of pattern Quantities delivered (tonne)

T R Less than 5 5 - 14 15 - 39 40 - 250 More than 2503 25.55 27.55 13.5 13 12 11.5 114 33.40 35.40 13.5 13 12 11.5 115 41.25 43.25 13.5 13 12 11.5 116 49.10 51.10 13.5 13 12 11.5 117 56.95 58.95 13.5 13 12 11.5 118 64.80 66.80 11.5 11 10 9.5 99 72.65 74.65 11.5 11 10 9.5 9

10 80.50 82.50 11.5 11 10 9.5 9

Deviation

DIN EN 59220 - 2000

Ho

t R

olle

d P

rod

uct

s


Pac

kag

ing


Packaging

HRU Hot rolled sheet cut from coil with trimmed edgeHRUKK Hot rolled sheet cut from coil with mill edgeTHRU Hot rolled, skin-passed sheet cut from coil with trimmed edgeLR Hot rolled plate cut from coil with trimmed edgeLRKK Hot rolled plate cut from coil with mill edgeL Heavy plate with trimmed edgeLKK Heavy plate with mill edgeDS Casted slab (extra heavy plate with mill edge)

Hot Rolled Cut To Length Plate Products

HRU, HRUKK, THRU, LR, LRKK • Length ≤ 3 m, thickness ≤ 6 mm. • Wooden pallet and strapping.

HRU, HRUKK, THRU, LR, LRKK, L, LKK, DS• Length > 3 m, thickness ≤ 6 mm.• Wooden skids-lenghtwise (5x9,5x250 cm)

and strapping.

LR, LRKK, L, LKK, DS • Length is insignificant, thickness > 6 mm.• Wooden skids-crosswise (8x8x80-100 cm)• Overseas shipment; strapping.

Ho

t R

olle

d P

rod

uct

s

Hot Rolled Pickled Cut To Length Plate Products

HRP, LP, TLPKK, THRPK, HRPKK,LPKK, TLP, THRP • Length ≤ 3 m, thickness ≤ 6 mm. • Wooden pallet, PE waterproof

paper and strapping.

• Length ≤ 3 m, thickness ≤ 6 mm. • Wooden pallet, PE waterproof

paper, galvanized metal cover andstrapping.

LP, LPKK, TLP, TLPKK• Length >3 m, thickness > 6 mm. • Wooden skids-crosswise

(8x8x80-100 cm)• PE waterproof paper and

strapping.

• Length > 3 m, thickness >6 mm.• Wooden skids-crosswise

(8x8x80 -100 cm), PE waterproofpaper and strapping.

HRP Hot rolled, pickled sheet cut from coil with trimmed edgeLP Hot rolled, pickled plate cut from coil with trimmed edgeTLPKK Hot rolled, skin-passed and pickled sheet cut from coil with mill edgeTHRPK Hot rolled, skin-passed and pickled sheet cut from coil with mill edgeHRPKK Hot rolled, pickled sheet cut from coil with mill edgeLPKK Hot rolled, pickled plate cut from coil with mill edgeTLP Hot rolled, skin-passed and pickled sheet cut from coil with trimmed edgeTHRP Hot rolled, skin-passed and pickled sheet cut from coil with trimmed edge

Overseas Shipment

122

HRP, LP, TLPKK, THRPK, HRPKK,LPKK, TLP, THRP• Length > 3 m, thickness ≤ 6 mm.• Wooden skids-lengthwise

(5x9,5x250 cm).• PE waterproof paper and

strapping.

Ho

t R

olle

d P

rod

uct

s


Pac

kag

ing


R Hot rolled coil with trimmed edgeRKK Hot rolled coil with mill edgeTRKK Hot rolled skin-passed coil with mill edgeMRKK Hot rolled, patterned coil with mill edgeBCKK Hot rolled coil with mill edge processed in recoiling line for cold rollingHCKK Hot rolled coil with mill edge for cold rollingTCKK Hot rolled coil with mill edge skin-passed in recoiling line for cold rollingBRKK Hot rolled coil with mill edge processed in recoiling lineKRKK Hot rolled heavy-thickness coil with mill edgeTR Hot rolled skin-passed coil with trimmed edge

Hot Rolled Coil Products

Overseas Shipment

• 3 circumferential straps.• 3 radial straps.

• 3 circumferential straps.• 4 radial straps.

Ho

t R

olle

d P

rod

uct

s

124

Hot Rolled Pickled Coil Products

RP Hot rolled, pickled coil with trimmed edgeRPKK Hot rolled, pickled coil with mill edgeTRP Hot rolled, skin-passed, pickled coil with trimmed edgeTRPKK Hot rolled, skin-passed, pickled coil with mill edge

Overseas Shipment

• PE waterproof paper.• 2 inside edge protection rings.• 2 circumferential straps.• 3 radial staps.

• PE waterproof paper.• 2 inside edge protection rings.• 2 outside edge protection rings.• 2 side protection disks.• Inside protection cover (Galvanized

sheet).• Outside protection cover (Galvanized

sheet).• 3 circumferential straps.• 4 radial staps.

Ho

t R

olle

d P

rod

uct

s


Pac

kag

ing


Hot Rolled Slitted Coil Products

RD Hot rolled, slitted coil

Overseas Shipment

• Every single band with 2circumferential straps and 3 radialstraps.

• Final strapping of bands withwooden pallet.


• Wrapping of bands with PEwaterproof paper.


Ho

t R

olle

d P

rod

uct

s

126

Hot Rolled Pickled Slitted Coil Products

RPD Hot rolled, pickled, slitted coilTRPD Hot rolled, skin-passed, pickled, slitted coil

• Every single band with 2 circumferentialstraps and 3 radial straps.

• Wrapping of bands with PE waterproofpaper.

• Final strapping of bands with woodenpallet.



Cold Rolled Flat Steel Products

130 > Grade Index 132 > Steel Grades149 > Available Sizes156 > Tolerances159 > Packaging

Co

ld R

olle

d P

rod

uct

s

128

Co

ld R

olle

d P

rod

uct

s

03129


www.erdemir.com.tr

Cold Rolled Flat Steel Products

The steel grades for cold formingcan be preferred when bending and deep drawing processes wheretoughness and ductile properties are required. These steels are mainlyused in automotive components and body panels, metal furniture,appliances, radiators, some profilesand ventilation equipments.

Non-aging extra deep-drawingsteels (IF) are the best material to


fulfill automotive and white goodssector's special expectations.

High strength low alloy cold rolledsteels (HSLA), that combineimproved weldability with goodformability, low content of bothcarbon and micro-alloying elementsare mainly used in automotivesuspension components,reinforcements, industrial shelvingsystems and furniture production.

Cold rolled steels for enamelling aresuitable for light and deep drawingand enamelling can be applicatedone/two coats or one/two fires.These steels are used for kitchenutensils (cookers, pots, pans) anddomestic appliances (oven grates,lids).

Cold rolled flat steel products are produced by two main rolling processes ashot rolling and finally cold rolling into 0.20-2.00 mm thicknesses. The productsare in the form of coils or cut into various lengths as plate. While the product'sphysical properties are all homogeneous along the strip, surface flatness,width and thickness values have fulfilled expectations at the top level.

Co

ld R

olle

d P

rod

uct

s

130

Grade Index

Application Areas and Brand Correspondence of Cold Rolled Products


And Major ApplicationsErdemir

Steel Grade Standard Grade

1110 Erdemir-01 1110Commercial quality steels for bending and 6106 SAE J403-01 1006moderate drawing (office equipments, 6108 SAE J403-01 1008automobile parts, etc.) 7608 SAE J403-01 10B08

6110 SAE J403-01 10106112 DIN EN 10130-99 DC O16113 DIN EN 10130-99 DC O3

Low-carbon drawing quality steels for general use

6114 DIN EN 10130-99 DC O47111 DIN EN 10130-99 DC O16612 DIN EN 10130-99 DC O17612 DIN EN 10130-99 DC O1120 SPC 270C-Erdemir TY01 120121 SPC 270C-Erdemir TY02 121

7114 DIN EN 10130-99 DC O47115 DIN EN 10130-99 DC O5

Non-aging extra deep-drawing 7116 DIN EN 10130-99 DC O6quality steels 130 XES-Erdemir RN01 130

131 SPC 270D-Erdemir TY03 131132 SPC 270D-Erdemir TY04 132

Extra deep-drawing steels for home appliances 7122 DIN EN 10130-99 DC O1(refrigerators, washing machines, etc.) 7123 DIN EN 10130-99 DC O3Ultra deep-drawing steel for filters in automotive industry 7124 DIN EN 10130-99 DC O4

Ultra low-carbon (IF) steels for use in automotive industry.7314 DIN EN 10130-99 DC O47315 DIN EN 10130-99 DC O57316 DIN EN 10130-99 DC O67512 DIN EN 10209-96 DC 01 EKModerate drawing and extra deep drawing steels for6513 DIN EN 10209-96 DC 04 EKporcelain enameling (bathtubs, sinks, kitchen 7513 DIN EN 10209-96 DC 04 EKutensils, panels, blackboards, signboards)7514 DIN EN 10209-96 DC 06 ED

Cold rolled rephosphorized steels with high yield strength for cold forming

7726 Erdemir-06 7726

Cold rolled bake-hardening steels with high yield strength for cold forming 7022 Erdemir-06 7022

Cold rolled dual-phase steels with higher yield strength for cold forming

7660 FE600 DPF Erdemir FT01 7660

7125 DIN EN 10268-99 H240 LA7128 DIN EN 10268-99 H280 LA7132 DIN EN 10268-99 H320 LA

High strength steels with improved formability 7136 DIN EN 10268-99 H360 LA(automobile parts, bicycle frames, building materials) 7140 DIN EN 10268-99 H400 LA

250 XE-320DR-Erdemir RN02 250251 F1 Gr. 300-Erdemir FR01 251260 XE-360DR-Erdemir RN03 260

5130 SAE J403-01 1030Full-hard high-carbon steels for general use (shovels, 5140 SAE J403-01 1040rakes, hand barrows, dust pans)

5145 SAE J403-01 1045High-carbon steel for specific use 5155 Erdemir-01 5155Cold-rolled rephosphorized steel for production of electric engines 5105 Erdemir-05 5105Cold-rolled steel for production of electric engines 6109 Erdemir-01 6109Medium carbon structural steel for galvanizing 4137 DIN 1623-P2-86 St 37-3 GNon-alloyed medium carbon steel for strap 6137 DIN 1623-P2-86 St 37-3 GSteels for atmospheric corrosion resistance (containers, rolling 6182 DIN EN 10130-99 DC O1 (Cu)stock, wall panels in a sulfurous atmosphere, etc.) 9160 JIS G 3125-04 SPA - C


Co

ld R

olle

d P

rod

uct

s

05

Gra

de

Ind

ex

131


www.erdemir.com.tr


Material Number Previous EN USA JIS Page Number

146G10060 ASTM A1008 CS Type A 146G10080 146G10081 146G10100 1461.0330 St12 EN 10130 - 98 ASTM A1008 CS Type B JIS G3141 SPCC 1321.0347 RRSt13 EN 10130 - 98 ASTM A1008 DS Type B JIS G3141 SPCD 1321.0338 St14 EN 10130 - 98 ASTM A620 CR DDQAK JIS G3141 SPCEN 1321.0330 St12 EN 10130 - 98 ASTM A366 CR CQ JIS G3141 SPCC 1321.0330 St12 EN 10130 - 98 ASTM A366 CR CQ JIS G3141 SPCC 1321.0330 St12 EN 10130 - 98 ASTM A366 CR CQ JIS G3141 SPCC 132

RRSt13 EN 10130 - 98 ASTM A619 CR DQ JIS G3141 SPCD 134RRSt13 EN 10130 - 98 ASTM A619 CR DQ JIS G3141 SPCD 134

1.0338 St14 EN 10130 - 98 ASTM A1008 DS Type A JIS G3141 SPCEN 1351.0312 FeP05 EN 10130 - 98 ASTM A1008 DDS 1351.0873 FeP06 EN 10130 - 98 ASTM A1008 EDDS 135

St14 EN 10130 - 98 ASTM A620 CR DDQAK JIS G3141 SPCEN 137St14 EN 10130 - 98 ASTM A620 CR DDQAK JIS G3141 SPCEN 137St14 EN 10130 - 98 ASTM A620 CR DDQAK JIS G3141 SPCEN 137

1.0330 St12 EN 10130 - 98 ASTM A366 CR CQ JIS G3141 SPCC 1351.0347 RRSt13 EN 10130 - 98 ASTM A619 CR DQ JIS G3141 SPCD 1351.0338 St14 EN 10130 - 98 ASTM A620 CR DDQAK JIS G3141 SPCEN 1361.0338 St14 EN 10130 - 98 ASTM A1008 DS Type A JIS G3141 SPCEN 1361.0312 FeP05 EN 10130 - 98 ASTM A1008 DDS 1361.0873 FeP06 EN 10130 - 98 ASTM A1008 EDDS 1361.0390 DIN 1623-3 EK2 EN 10209 - 96 1381.0392 DIN 1623-3 EK4 EN 10209 - 96 ASTM A424 Type2 1381.0392 DIN 1623-3 EK4 EN 10209 - 96 ASTM A424 Type-2 1381.0872 FeD6 EN 10209 - 96 ASTM A424 Type-3 138

SEW 094-87 ZStE260 P 139

1.0396 SEW 094-87 ZStE220 BH ASTM A1008 BHS Gr.31 140

141

1.0480 SEW093 ZStE240 EN 10268 - 98 ASTM A1008 SS Gr.33 1421.0489 SEW093 ZStE260 EN 10268 - 98 ASTM A1008 SS Gr.40 1421.0548 SEW093 ZStE300 EN 10268 - 98 ASTM A1008 HSLAS Gr.45 Class 2 1421.0550 SEW093 ZStE340 EN 10268 - 98 ASTM A1008 HSLAS Gr.50 Class 2 1421.0556 SEW093 ZStE380 EN 10268 - 98 ASTM A1008 HSLAS Gr.55 Class 2 142

SEW093 ZStE300 EN 10268 - 98 ASTM A607 Gr.45 143SEW093 ZStE300 EN 10268 - 98 ASTM A607 Gr.45 143SEW093 ZStE340 EN 10268 - 98 ASTM A607 Gr.50 143

G10300 146G10400 146G10450 146

148144144

1.0116G ASTM A1008 SS Gr.33 Type 1 1451.0116G ASTM A1008 SS Gr.30 1451.0330 St12 EN 10130 - 98 ASTM A366 CR CQ JIS G3141 SPCC 132

147

Co

ld R

olle

d P

rod

uct

s

132

Steel Grades

Cold Rolled Low Carbon Products For Drawing and Cold FormingStandard: DIN EN 10130 - 1999


Notes1- Copper = 0.15 - 0.35%2- The grades 6114, 6182, 6612 are produced by batch-annealing.3- The grades 6612, 7111, 7612 are suitable for welding of electric-resistance.

Erdemir Validity ofSteel Corresponding Chemical C P S Mn MechanicalGrade Standard Grade Limits max. max. max. max. Properties

6112 DIN EN 10130 DC01Standard 0.12 0.045 0.045 0.60 6 MonthErdemir 0.07 0.020 0.020 0.40

6182 (1) (2) DIN EN 10130 DC01Standard 0.12 0.045 0.045 0.60 6 MonthErdemir 0.07 0.020 0.020 0.40

6113 DIN EN 10130 DC03Standard 0.10 0.035 0.035 0.45 6 MonthErdemir 0.07 0.020 0.015 0.35

6114 (2) DIN EN 10130 DC04Standard 0.08 0.030 0.030 0.40 6 MonthErdemir 0.07 0.015 0.015 0.35


6612 (2) (3) DIN EN 10130 DC01Standard 0.12 0.045 0.045 0.60 6 MonthErdemir 0.06 0.020 0.020 0.30


Co

ld R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

133


Notes1- The values for the tensile test apply to “Transverse” test pieces.2- The value for yield stress is increased by 20 N/mm2 (2,0 kg/mm2) for thickness greater than 0.5 mm and less than or equal to 0.7 mm.

For thickness less than or equal to 0.5 mm, the value is increased by 40 N/mm2 (4,1 kg/mm2)3- When the thickness is less than or equal to 0.7 mm and greater than 0.5 mm, the minimum value for elongation is reduced by 2 units. For

thickness less than or equal to 0.5 mm, the minimum value is reduced by 4 units.4- The values of r90 and n90 only apply to products of thickness greater than or equal to 0.5 mm.5- For design purposes, the lower limit of Re may be assumed to be 140 N/mm2 (14.3 kg/mm2).


ErdemirRe

(2) (5) Rm (1) A80

(3) r90(4) n90

(4)

SteelN/mm2 N/mm2 (%)

GradeCorresponding (kg/mm2) (kg/mm2)

Standard Grade max. min. min. min.

6112 DIN EN 10130 DC01280 270 - 410 28 - -

(28.6) (27.5 - 41.8)

6182 DIN EN 10130 DC01280 270 - 410 28 - -

(28.6) (27.5 - 41.8)

6113 DIN EN 10130 DC03240 270 - 370 34 1.3 -

(24.5) (27.5 - 37.7)

6114 DIN EN 10130 DC04210 270 - 350 38 1.6 0.18

(21.4) (27.5 - 35.7)

7111 DIN EN 10130 DC01280 270 - 410 28 - -

(28.6) (27.5 - 41.8)

6612 DIN EN 10130 DC01280 270 - 410 28 - -

(28.6) (27.5 - 41.8)

7612 DIN EN 10130 DC01280 270 - 410 28 - -

(28.6) (27.5 - 41.8)

Re Rm (1) A80 r90

Erdemir (%)Steel Corresponding N/mm2 N/mm2

Grade User Applied Similar (kg/mm2) (kg/mm2)Sector Standard Standard min. min. max. min.

120 (2) Automotive SPC270C-Erdemir TY01 DIN EN 10130 DC03165 - 225 270 38 45 1.3

(16.8 - 23.0) (27.6)

121 (2) Automotive SPC270C-Erdemir TY02 DIN EN 10130 DC03165 - 225 270 40 47 1.3

(16.8 - 23.0) (27.6)

Co

ld R

olle

d P

rod

uct

s

10 134

Cold Rolled Low Carbon Products For Deep Drawing Standard: Erdemir



Notes1- The values for all mechanical tests of grade 120 are applicable for thickness greater than or equal to 0.40 mm and less than 1.00 mm.2- The values for all mechanical tests of grade 121 are applicable for thickness greater than or equal to 1.00 mm and less than 1.40 mm.

Notes1- The values for the tensile test apply to “Transverse” test pieces.2- Surface roughness for products of grades 120, 121 is in the range of 0.70 - 1.30 µm.

Erdemir CorrespondingSteel Grade User Applied Similar C Mn P S Si Al

Sector Standard Standard max. max. max. max. max. min.120 (1) Automotive SPC270C-Erdemir TY01 DIN EN 10130 DC03 0.05 0.25 0.020 0.015 0.040 0.02121 (1) Automotive SPC270C-Erdemir TY02 DIN EN 10130 DC03 0.05 0.20 0.020 0.015 0.035 0.02

Co

ld R

olle

d P

rod

uct

s

11

Ste

el G

rad

es

135


www.erdemir.com.tr

Notes1- The values for the tensile test apply to “Transverse” test pieces.2- The values of rm (mean value) and nm (mean value) are shown on the table.3- The value for y›eld stress is increased by 20 N/mm2 (2,0 kg/mm2) for thickness greater than 0.5 mm and less than or equal to 0.7 mm.

For thickness less than or equal to 0.5 mm, the value is increased by 40 N/mm2 (4,1 kg/mm2)4- When the thickness is less than or equal to 0.7 mm and greater than 0.5 mm, the minimum value for elongation is reduced by 2 units.

For thickness less than or equal to 0.5 mm, the minimum value is reduced by 4 units.5- The values of r90 and n90 only apply to products of thickness greater than or equal to 0.5 mm.6- For design purposes, the lower limit of Re may be assumed to be 140 N/mm2 (14.3 kg/mm2).7- For design purposes, the lower limit of Re may be assumed to be 120 N/mm2 (12.2 kg/mm2).


Cold Rolled Ultra Low Carbon Deep Drawing Products For Home AppliancesStandard: DIN EN 10130 - 1999


ErdemirSteel

Re (3) Rm

(1) A80 (4) r90 (5) n90

(5)

GradeN/mm2 N/mm2 (%)

Corresponding (kg/mm2) (kg/mm2)Standard Grade max. min. min. min.

7114 (6) DIN EN 10130 DC04210 270 - 350 38 1.6 0.18

(21.4) (27.5 - 35.7)

7115 (6) DIN EN 10130 DC05180 270 - 330 40 1.9 0.20

(18.4) (27.5 - 33.7)

7116 (7) DIN EN 10130 DC06180 270 - 350 38 1.8 (2) 0.22 (2)

(18.4) (27.5 - 35.7)

7122 (6) DIN EN 10130 DC01280 270 - 410 28 - -

(28.6) (27.5 - 41.8)

7123 (6) DIN EN 10130 DC03240 270 - 370 34 1.3 -

(24.5) (27.5 - 37.7)

Validity ofErdemirMechanicalSteel

Corresponding Chemical C P S Mn Ti PropertiesGradeStandard Grade Limits max. max. max. max. max.

7114 DIN EN 10130 DC04Standard 0.08 0.030 0.030 0.40 - 6 MonthErdemir 0.006 0.015 0.015 0.25 0.10


7116 DIN EN 10130 DC06Standard 0.02 0.020 0.020 0.25 0.30 No LimitErdemir 0.004 0.012 0.009 0.20 0.10



Co

ld R

olle

d P

rod

uct

s

136

Cold Rolled Ultra Low Carbon Deep Drawing Products For Use In Automotive IndustryStandard: DIN EN 10130 - 1999


Notes1- The values for the tensile test apply to “Transverse” test pieces.2- The values of rm (mean value) and nm (mean value) are shown on the table.3- The value for y›eld stress is increased by 20 N/mm2 (2,0 kg/mm2) for thickness greater than 0.5 mm and less than or equal to 0.7 mm. For

thickness less than or equal to 0.5 mm, the value is increased by 40 N/mm2. (4,1 kg/mm2)4- When the thickness is less than or equal to 0.7 mm and greater than 0.5 mm, the minimum value for elongation is reduced by 2 units. For

thickness less than or equal to 0.5 mm, the minimum value is reduced by 4 units.5- The values of r90 and n90 only apply to products of thickness greater than or equal to 0.5 mm.6- For design purposes, the lower limit of Re may be assumed to be 140 N/mm2. (14.3 kg/mm2).7- For design purposes, the lower limit of Re may be assumed to be 120 N/mm2. (12.2 kg/mm2).


Notes1- The spot welding is suitable for grades 7314, 7315, 7316.

Validity ErdemirofSteel

Corresponding Chemical C P S Mn Ti MechanicalGradeStandard Grade Limits max. max. max. max. max. Properties


7314 (1) DIN EN 10130 DC04Standard 0.08 0.030 0.030 0.40 - 6 MonthErdemir 0.006 0.015 0.012 0.25 0.07

7315 (1) DIN EN 10130 DC05Standard 0.06 0.025 0.025 0.35 - 6 MonthErdemir 0.004 0.012 0.010 0.25 0.06

7316 (1) DIN EN 10130 DC06Standard 0.02 0.020 0.020 0.25 0.30 No LimitErdemir 0.004 0.010 0.008 0.15 0.06

Re (3) Rm

(1) A80 (4) r90

(5) n90(5)

ErdemirN/mm2 N/mm2 (%)Steel

Corresponding (kg/mm2) (kg/mm2)GradeStandard Grade max. min. min. min.

7124 (6) DIN EN 10130 DC04210 270 - 350 38 1.6 0.18

(21.4) (27.5 - 35.7)

7314 (6) DIN EN 10130 DC04210 270 - 350 38 1.6 0.18

(21.4) (27.5 - 35.7)

7315 (6) DIN EN 10130 DC05180 270 - 330 40 1.9 0.20

(18.4) (27.5 - 33.7)

7316 (7) DIN EN 10130 DC06180 270 - 350 38 1.8 (2) 0.22 (2)

(18.4) (27.5 - 35.7)

Co

ld R

olle

d P

rod

uct

s

09

Ste

el G

rad

es

137


www.erdemir.com.tr

Cold Rolled Ultra Low Carbon Deep Drawing Products For Use In Automotive IndustryStandard: Erdemir



Notes1- The values for all mechanical tests of grade 131 are applicable for thickness greater than or equal to 0.40 mm and less than 1.00 mm.2- The values for all mechanical tests of grade 132 are applicable for thickness greater than or equal to 1.00 mm and less than 1.40 mm.

Notes1- The values for the tensile test apply to “Transverse” test pieces.2- Re / Rm: 0.66 max.3- Surface roughness for products of grades 131, 132 is in the range of 0.70 - 1.30 µm.

Erdemir CorrespondingSteel User Applied Similar C Mn P S Ti NbGrade Sector Standard Standard max. max. max. max. max. max.130 Automotive XES-Erdemir RN01 DIN EN 10130 DC04 0.005 0.25 0.015 0.012 0.07 0.030131 (1) Automotive SPC270D-Erdemir TY03 DIN EN 10130 DC04 0.006 0.25 0.015 0.012 0.10 0.005132 (1) Automotive SPC270D-Erdemir TY04 DIN EN 10130 DC04 0.006 0.25 0.015 0.012 0.09 0.005

Re Rm(1) A80 r r90 n n90

Erdemir Corresponding N/mm2 N/mm2 (%)Steel User Applied Similar (kg/mm2) (kg/mm2)Grade Sector Standard Standard min. min. max. min. min. min. min.

130 (2) Automotive XES-Erdemir RN01 DIN EN 10130 DC04160 - 200 280 - 350 38 1.80 0.19

(16.3 - 20.4) (28.6 - 35.7)

131 (3) Automotive SPC270D-Erdemir TY03 DIN EN 10130 DC04145 - 190 270 41 48 1.40 0.20

(14.8 - 19.4) (27.6)

132 (3) Automotive SPC270D-Erdemir TY04 DIN EN 10130 DC04145 - 190 270 43 50 1.40 0.20

(14.8 - 19.4) (27.6)

Co

ld R

olle

d P

rod

uct

s

12 138

Cold Rolled Low Carbon Steel For Vitreous Enamelling Standard: DIN EN 10209 - 1996


Notes1- Products of grade 6513 are produced by batch-annealing.


Notes1- The values for the tensile test apply to “Transverse” test pieces.2- The values of rm only apply to products of thicknesses equal to or greater than 0.5 mm.

3- When the thickness is less than or equal to 0.7 mm and greater than 0.5 mm, the value is increased by 20 N/mm2 (2,0 kg/mm2). For thicknesses equal to or less than 0.5 mm, the value for yield stress is increased by 40 N/mm2 (4,1 kg/mm2).

4- When the thickness is less than or equal to 0.7 mm and greater than 0.5 mm, the minimum elongation value isreduced by 2 units. For thicknesses equal to or less than 0.5 mm, the minimum value after fracture is reduced by 4 units.

5- For design purposes, the lower limit of yield strength for qualities 7512, 7513 may be assumed to be 140 N/mm2 (14.3 kg/mm2) and for quality 7514 as 120 N/mm2 (12.2 kg/mm2).

ValidityErdemir ofSteel Corresponding Chemical C Ti MechanicalGrade Standard Grade Limits max. max. Properties

7512 DIN EN 10209 DC01 EKStandard 0.08 - 6 MonthErdemir 0.06 -

6513 (1) DIN EN 10209 DC04 EKStandard 0.08 - 6 MonthErdemir 0.05 -

7513 DIN EN 10209 DC04 EKStandard 0.08 - 6 MonthErdemir 0.05 -

7514 DIN EN 10209 DC06 EDStandard 0.02 0.30 6 MonthErdemir 0.005 0.15

ErdemirRe

(3) Rm (1) A80(4) rm

(2)

SteelN/mm2 N/mm2 (%)

GradeCorresponding (kg/mm2) (kg/mm2)

Standard Grade max. min. min.

7512 (5) DIN EN 10209 DC01 EK270 270 - 390 30 -

(27.5) (27.5 - 39.8)

6513 (5) DIN EN 10209 DC04 EK220 270 - 350 36 -

(22.4) (27.5 - 35.7)

7513 (5) DIN EN 10209 DC04 EK220 270 - 350 36 -

(22.4) (27.5 - 35.7)

7514 (5) DIN EN 10209 DC06 ED190 270 - 350 38 1.6

(19.4) (27.5 - 35.7)

Co

ld R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

139



Notes1- The grade 7726 also corresponds to the grade “ZStE260P” in standard SEW 094-87.2- C + P ≤ 0.16%.

Notes1- The values for the tensile test apply to “Longitudinal” test pieces.2- The mechanical properties are valid for a period of 6 months from the date on which the products are made available.

Mechanical Properties(2)

Cold Rolled Rephosphorized Steel With High Yield Strength For Cold Forming Standard: Erdemir

ErdemirSteel Corresponding Chemical C (2) Si Mn P (2) S AlGrade Standard Grade Limits max. max. max. max. max. min.

7726 (1) Erdemir-2006 7726Standard 0.08 0.50 0.70 0.10 0.030 0.020Erdemir 0.01 0.10 0.70 0.10 0.015 0.020

Re Rm(1) A80 Bend

ErdemirN/mm2 N/mm2 (%) (Trans., 180o)

SteelCorresponding (kg/mm2) (kg/mm2) mdb

GradeStandard Grade min. (d: thickness)

7726 Erdemir-2006 7726260 - 320 380 - 460 28 0

(26.5 - 32.7) (38.8 - 46.9)

Co

ld R

olle

d P

rod

uct

s

140

Notes1- The values for mechanical test apply to “Transverse” test pieces.2- BH of ≥ 40 N/mm2 can only be guaranteed for thickness ≤ 1.00 mm. For thickness > 1.00 mm, the minimum guaranteed BH is 30 N/mm2.

(3.1 kg/mm2)

Notes1- The grade 7022 also corresponds to the grade “SEW 094-87 ZStE 220 BH”.2- Vanadium and boron may also be added.

Cold Rolled Bake Hardening Steel With High Yield Strength For Cold FormingStandard: Erdemir

Chemical Composition (%)(2)


ValidityErdemir ofSteel Corresponding Chemical C Si Mn P S Al MechanicalGrade Standard Grade Limits max. max. max. max. max. min. Proporties

7022 (1) Erdemir-06 7022Standard 0.06 0.50 0.70 0.08 0.030 0.02 3 MonthErdemir 0.01 0.03 0.60 0.06 0.015 0.02

Rp0.2

Erdemir or Re BH (2) Rm (1) A80 r90 n90

Steel N/mm2 N/mm2 N/mm2 (%)Grade Corresponding (kg/mm2) (kg/mm2) (kg/mm2)

Standard Grade min. min. min. min.

7022 Erdemir-06 7022220 - 280 40 320 - 400 30 1.6 0.17

(22.4 - 28.6) (4.1) (32.7 - 40.8)

Co

ld R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

141


Notes1- The values for mechanical test apply to “Longitudinal” test pieces.2- For thickness values between 0.50 and 0.70 mm reduce of 2 units; for thickness values lower than 0.50 mm reduce of 4 units. 3- The mechanical properties are valid for a period of 3 months from the date on which the products are made available. 4- The bend test is carried only when specified at the time of the enquiry and order. 5- n (10-20%) ≥ 0.14. If the maximum value of uniform elongation is lower than 20%, the value of n is determined between 10% and the

maximum value of uniform elongation. 6- n (4-6%) ≥ 0.18.

Cold Rolled Dual Phase Steel With Higher Yield Strength For Cold FormingStandard: Erdemir


Mechanical Properties (3) (5) (6)

ErdemirSteel Corresponding Chemical C Si Mn P S Al Cr NbGrade Standard Grade Limits max. max. max. max. max. min. max. max.

7660 FE600DPF Erdemir FT01 7660Standard 0.14 0.40 1.60 0.09 0.010 0.02 1.00 0.03Erdemir 0.11 0.25 1.30 0.06 0.010 0.02 0.80 0.01

Rp0.2 BH2 Rm (1) A80

(2)

Erdemir or Re (%) Bend (4)

Steel N/mm2 N/mm2 N/mm2 (Trans., 90o)Grade Corresponding (kg/mm2) (kg/mm2) (kg/mm2) mrb

Standard Grade min. min. (d: thickness)

7660 FE600DPF Erdemir FT01 7660340 - 440 30 600 - 700 21 0.5 d

(34.7 - 44.9) (3.1) (61.2 - 71.4)

Re Rm(1) A80 Bend

Erdemir N/mm2 N/mm2 (%) (Trans., 180o)Steel Corresponding (kg/mm2) (kg/mm2) mdbGrade Standard Grade min. min. (d: thickness)

7125 DIN EN 10268 H240 LA240 - 310 340 27 0

(24.5 - 31.6) (34.7)

7128 DIN EN 10268 H280 LA280 - 360 370 24 0

(28.6 - 36.7) (37.8)

7132 DIN EN 10268 H320 LA320 - 410 400 22 0

(32.7 - 41.8) (40.8)

7136 DIN EN 10268 H360 LA360 - 460 430 20 0.5 d

(36.7 - 46.9) (43.9)

7140 DIN EN 10268 H400 LA400 - 500 460 18 0.5 d

(40.8 - 51.0) (46.9)

Co

ld R

olle

d P

rod

uct

s

142


Cold Rolled Steels With High Yield Strength For Cold Forming Standard: DIN EN 10268 - 1999

Notes1- Nb + Ti + V ≤ 0.22%.

Notes1- The values for the tensile test apply to “Longitudinal” test pieces.


ErdemirSteel Corresponding Chemical C Si Mn P S Al Nb (1) Ti (1) V (1)

Grade Standard Grade Limits max. max. max. max. max. min. max. max. max.

7125 DIN EN 10268 H240 LAStandard 0.10 0.50 0.60 0.025 0.025 0.015 0.090 0.15 0.20Erdemir 0.08 0.10 0.50 0.020 0.015 0.020 0.040 0.06 0.06





Co

ld R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

143


Cold Rolled Steel With High Yield Strength For Cold Forming Standard: Erdemir

Notes1- The values for the tensile test apply to “Longitudinal” test pieces.2- Surface roughness for product of grade 251 is in the range of 1.00 - 1.70 µm.3- Re / Rm: 0.85 max.



Erdemir CorrespondingSteel User Applied Similar C Mn P S Si Nb VGrade Sector Standard Standard max. max. max. max. max. max. max.

250 Automotive XE-320 DR-Erdemir RN02 DIN EN 10268 H320 LA 0.10 0.90 0.020 0.015 0.04 0.08 0.06251 Automotive F1 Gr.300-Erdemir FR01 DIN EN 10268 H320 LA 0.10 0.80 0.020 0.015 0.04 0.08 0.06260 Automotive XE-360 DR-Erdemir RN03 DIN EN 10268 H360 LA 0.10 1.00 0.020 0.015 0.04 0.08 0.08

A50 A80Erdemir Re Rm

(1) (%) (%)Steel BendGrade Corresponding N/mm2 N/mm2 (Trans., 1800)

User Applied Similar (kg/mm2) (kg/mm2) mdbSector Standard Standard min. min. min. (d: thickness)

250 (3) Automotive XE-320 DR-Erdemir RN02 DIN EN 10268 H320 LA320 - 380 415 - 480 24 0

(32.7 - 38.8) (42.3 - 49.0)

251 (2) Automotive F1 Gr.300-Erdemir FR01 DIN EN 10268 H320 LA300 - 400 400 23 0

(30.6 - 40.8) (40.8)

260 (3) Automotive XE-360 DR-Erdemir RN03 DIN EN 10268 H360 LA360 - 430 450 - 530 21 0.5 d

(36.7 - 43.9) (45.9 - 54.1)

Co

ld R

olle

d P

rod

uct

s

144



Cold Rolled Rephosphorized Steel For Production Of Electric Engines Standard: Erdemir

Cold Rolled Steel For Production Of Electric EnginesStandard: Erdemir



ErdemirSteel Corresponding C Mn P S Si Al NGrade Standard Grade max. max. max. min. max.

6109 (1) Erdemir - 2001 6109 0.02 1.00 0.01 - 0.03 0.020 0.10 - 0.30 0.020 0.009

ErdemirSteel Corresponding C Mn P S Si AlGrade Standard Grade max. max.

5105 (1) Erdemir - 2005 5105 0.05 0.30 - 0.60 0.03 - 0.15 0.015 0.10 - 0.25 0.020 - 0.060

Co

ld R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

145



Cold Rolled Structural Steel Standard: DIN 1623 - Part2 - 1986



ErdemirSteel Corresponding Chemical C P SGrade Standard Grade Limits max. max. max.

4137 DIN 1623 - P2 St 37-3 GStandard 0.17 0.040 0.035Erdemir 0.17 0.020 0.020

6137 DIN 1623 - P2 St 37-3 GStandard 0.17 0.040 0.035Erdemir 0.12 0.020 0.015

Erdemir Re Rm (1) A80 Bend

Steel N/mm2 N/mm2 (%) (Trans., 180o)

Grade Corresponding (kg/mm2) (kg/mm2) mdbStandard Grade min. min. (d: thickness)

4137 DIN 1623 - P2 St 37-3 G215 360 - 510 20 0.5 d

(21.9) (36.7 - 52.0)

6137 DIN 1623 - P2 St 37-3 G215 360 - 510 20 0.5 d

(21.9) (36.7 - 52.0)

Co

ld R

olle

d P

rod

uct

s

146

Cold Rolled Carbon Structural Steel With Specific Chemical Composition Standard: SAE J403 - 2001

Cold Rolled Commercial SteelStandard: Erdemir



Notes1- The products of grades 5130, 5140, 5145 are manufactured in “ Full-hard “ condition.


ErdemirSteel Corresponding Chemical C Mn P S Si BGrade Standard Grade Limits max. max. max. max. max.

6106 SAE J403 1006Standard 0.08 0.45 0.030 0.050 0.10 -Erdemir 0.07 0.45 0.020 0.015 0.03 -

6108 SAE J403 1008Standard 0.10 0.50 0.030 0.050 0.10 -Erdemir 0.08 0.50 0.020 0.015 0.04 -

7608 SAE J403 1008(B)Standard 0.10 0.50 0.030 0.050 0.10 -Erdemir 0.10 0.50 0.020 0.015 0.05 0.002 - 0.005

6110 SAE J403 1010Standard 0.08 - 0.13 0.30 - 0.60 0.030 0.050 0.10 -Erdemir 0.08 - 0.13 0.40 - 0.60 0.025 0.020 0.05 -

5130 (1) SAE J403 1030Standard 0.28 - 0.34 0.60 - 0.90 0.030 0.050 0.15 - 0.35 -Erdemir 0.28 - 0.34 0.60 - 0.90 0.030 0.030 0.15 - 0.35 -



ErdemirSteel Corresponding C Mn P S Si Al Grade Standard Grade max. max. max. max. max.

1110(1) Erdemir - 2001 1110 0.10 0.50 0.025 0.025 0.050 0.015 - 0.100

Co

ld R

olle

d P

rod

uct

s

www.erdemir.com.tr

Ste

el G

rad

es

147


Structural Steel With Improved Atmospheric Corrosion Resistance Standard: JIS G3125 - 2004


Notes1- Mangan upper limit may be set at 1.00% or less by agreement between the purchaser and the supplier.

ErdemirSteel Corresponding Chemical C Si Mn (1) P S Cu Cr NiGrade Standard Grade Limits max. max. max. max.

9160 JIS G3125 SPA - CStandard 0.12 0.20 - 0.75 0.60 0.070 - 0.150 0.035 0.25 - 0.55 0.30 - 1.25 0.65Erdemir 0.12 0.20 - 0.75 0.60 0.070 - 0.150 0.020 0.25 - 0.55 0.30 - 1.25 0.65

A50Erdemir Re Rm

(1) (%) BendSteel N/mm2 N/mm2 (long., 180o) Grade Corresponding (kg/mm2) (kg/mm2) mrb

Standard Grade min. min. min. (d: thickness)

9160 (2) JIS G3125 SPA - C315 450 26 0.5 d

(32.1) (45.9)


Notes1- The values for tensile test apply to “Longitudinal” test pieces.2- Values for mechanical test are not guaranteed.

Co

ld R

olle

d P

rod

uct

s

148

Cold Rolled High Carbon Steel For Specific UseStandard: Erdemir



Notes1- The values for tensile test apply to “Longitudinal” test pieces.

ErdemirSteel Corresponding C Mn P S SiGrade Standard Grade max. max.

5155 Erdemir - 2001 5155 0.52 - 0.60 0.70 - 0.90 0.020 0.010 0.15 - 0.30

Re Rm(1) A80Erdemir

N / mm2 N / mm2 (%)SteelCorresponding (kg / mm2) (kg / mm2)Grade

Standard Grade max. max. min.

5155 Erdemir - 2001 5155360 530 15

(36.7) (54.1)

Co

ld R

olle

d P

rod

uct

s


Ava

ilab

le S

izes


Cold Rolled Products

Available Sizes


Symbol min. max.

ICCR 0.20 0.40 Cold rolled, continuously annealed thin coil

CR 0.20 1.20 Cold rolled, batch annealed coil

CCR 0.40 2.00 Cold rolled, continuously annealed coil

CRF 0.20 2.00 Cold rolled, not annealed (full-hard) coil, produced in cold rolling mill no.1

CCRF 0.35 2.00 Cold rolled, not annealed (full-hard) coil, produced in cold rolling mill no.2

CRFS 0.30 2.00 Cold rolled, not annealed (full-hard) sheet cut from coil, produced in cold rolling mill no.1

CCRFS 0.35 2.00 Cold rolled, not annealed (full-hard) sheet cut from coil, produced in cold rolling mill no.2

CCRD 0.40 2.00 Cold rolled, continuously annealed, slitted coil

CRD 0.30 1.20 Cold rolled, batch annealed, slitted coil

CRK 0.30 1.20 Cold rolled, batch annealed coil with trimmed edge

CCRK 0.40 2.00 Cold rolled, continuously annealed coil with trimmed edge

CRSK 0.30 1.20 Cold rolled, batch annealed sheet cut from coil with trimmed edge

CCRSK 0.40 2.00 Cold rolled, continuously annealed sheet cut from coil with trimmed edge

CRS 0.30 1.20 Cold rolled, batch annealed sheet cut from coil

CCRS 0.40 2.00 Cold rolled, continuously annealed sheet cut from coil

Co

ld R

olle

d P

rod

uct

s

150

Notes1- The minimum width is 700 mm.2- For products of grade 6513, minimum thickness is 0.40 mm.3- Requests for the products with thickness thinner than 0,30 mm are only accepted for product type CR.4- Requests for the products equivalent to or thinner than 0.28 mm in thickness are only accepted for unoiled products.5- In case of grades 6113, 6114, requests for the products with thickness thinner than 0,30 mm are not accepted.6- Maximum width for product types CRK and CRSK is 1175 mm.7- Length: min. 914 mm, max. 4880 mm.8- Maximum bundle weight for products in form of sheet is 6 t.9- Coil weights are subject to negotiation.

CR Cold rolled, batch annealed coil

CRK Cold rolled, batch annealed coil with trimmed edge

CRS Cold rolled, batch annealed sheet cut from coil

CRSK Cold rolled, batch annealed sheet cut from coil with trimmed edge

DimensionsMaximum Width (mm) (2)

Thickness (mm)Group-A Group-B Group-C Group-D

0.20 - 0.29 10000.30 - 0.50 1200 10000.51 - 0.59 1200 11000.60 - 1.20 1200 1200

GradesGroup Code GradesA 1110, 6106, 6108, 6112, 6113, 6114, 6182, 6513, 6612B 6110Special 4137, 5155, 6109, 6137, 9160Available Sizes For Grades Of Special GroupGrade Product Type Thickness (mm) Width (mm)6109 CR, CRS 0,50 700 - 10004137, 6137 CR, CRS 0,90 - 1,20 900 - 12005155 CR, CRS 1,00 700 - 8009160 CR, CRS 1,00 - 1,20 700 - 900

Co

ld R

olle

d P

rod

uct

s


Ava

ilab

le S

izes


Notes1- The minimum width is 400 mm.2- For products of grade 6513, minimum thickness is 0.40 mm.3- Number of slits is subject to negotiation.

Notes1- The minimum width is 400 mm.2- For grades 120, 131, orders of thicknesses greater than or equal to 0.40 mm and less than 1.00 mm are accepted.3- For grades 121, 132, orders of thicknesses greater than or equal to 1.00 mm and less than 1.40 mm are accepted.

Number of slits is subject to negotiation.

CRD Cold rolled, batch annealed, slitted coil

DimensionsMaximum Width (mm)


0.30 - 1.20 699

GradesGroup Code GradesA 1110, 6106, 6108, 6110, 6112, 6113, 6114, 6182, 6513, 6612

CCRD Cold rolled, continuously annealed, slitted coil


Thickness (mm) (2) (3)

Group-A Group-B Group-C Group-D0.40 - 2.00 699 699 699 699

GradesGroup Code GradesA 120, 121, 1110, 6106, 6108, 6112, 6113, 7111, 7512, 7513, 7608, 7612B 130, 131, 132, 7022, 7114, 7115, 7116, 7122, 7123, 7124, 7314, 7315, 7316, 7514, 7726C 250, 251, 260, 7125, 7128, 7132, 7136, 7140, 7660D 4137, 5105, 6110, 6137

Co

ld R

olle

d P

rod

uct

s

152

Notes1- The minimum width is 700 mm.2- Requests for the products equivalent to or thinner than 0.25 mm in thickness are only accepted for unoiled and lightly oiled products.3- The products with thickness thinner than 0,30 mm are only produced as small coils.4- No limitation for coil weight.

Notes1- The minimum width is 700 mm.2- Requests for the products with thickness thinner than 0,30 mm are only accepted for product type CRF.3- Length: min. 914 mm, max. 4880 mm.4- Maximum bundle weight for products in form of sheet is 6 t.5- Coil weights are subject to negotiation.

CRF Cold rolled, not annealed (full-hard) coil, produced in cold rolling mill no.1

CRFS Cold rolled, not annealed (full-hard) sheet cut from coil, produced in cold rolling mill no.1



0.20 - 0.29 10000.30 - 0.50 1200 10000.51 - 0.59 1200 11000.60 - 2.00 1200 1200


A 1110, 6106, 6108, 6112, 6113, 6114, 6182, 6612

B 6110

Special 5130, 5140, 5145

Available Sizes For Grades Of Special Group

Grade Product Type Thickness (mm) Width (mm)

5130 CRF, CRFS 1,50 - 1,70 700 - 840

5140, 5145 CRF, CRFS 1,70 700 - 840

ICCR Cold rolled, continuously annealed thin coil



0.20 - 0.29 10000.30 - 0.55 1200

GradesGroup Code GradesA 1110, 6106, 6108, 6112, 7512, 7612

Co

ld R

olle

d P

rod

uct

s


Ava

ilab

le S

izes


Notes1- The minimum width is 700 mm.2- For grades 120, 131, orders of thicknesses greater than or equal to 0.40 mm and less than 1.00 mm are accepted.3- For grades 121, 132, orders of thicknesses greater than or equal to 1.00 mm and less than 1.40 mm are accepted.4- Length: min. 914 mm, max. 4880 mm.5- Maximum bundle weight for products in form of sheet is 6 t.6- Coil weights are subject to negotiation.7- Orders are not made for grades 1110, 6106, 6108, 6112, 7512, 7612 of products in product type CCR with thicknesses equal to and

thinner than 0.40 mm and widths equal to and narrower than 1200 mm; but for products in product type ICCR, it is possible to make an order.

CCR Cold rolled, continuously annealed coil

CCRS Cold rolled, continuously annealed sheet cut from coil



Group-A Group-B Group-C Group-D0.40 - 0.49 1150 1000 900 10000.50 - 0.50 1300 1000 900 10000.51 - 0.60 1300 1100 900 10000.61 - 0.70 1300 1200 900 11000.71 - 0.80 1400 1300 900 12000.81 - 0.90 1400 1400 1000 13000.91 - 0.99 1400 1400 1100 13001.00 - 1.00 1500 1500 1100 13001.01 - 1.20 1500 1500 1200 14001.21 - 2.00 1500 1500 1200 1500


Co

ld R

olle

d P

rod

uct

s

154

Notes1- The minimum width is 700 mm.2- For grades 120, 131, orders of thicknesses greater than or equal to 0.40 mm and less than 1.00 mm are accepted.3- For grades 121, 132, orders of thicknesses greater than or equal to 1.00 mm and less than 1.40 mm are accepted.4- Length: min. 914 mm, max. 4880 mm.5- Maximum bundle weight for products in form of sheet is 6 t.6- Coil weights are subject to negotiation.

CCRK Cold rolled, continuously annealed coil with trimmed edge

CCRSK Cold rolled, continuously annealed sheet cut from coil with trimmed edge



Group-A Group-B Group-C Group-D0.40 - 0.49 1150 975 875 10000.50 - 0.50 1275 975 875 10000.51 - 0.60 1275 1075 875 10000.61 - 0.70 1300 1175 900 11000.71 - 0.80 1400 1275 900 12000.81 - 0.90 1400 1400 1000 13000.91 - 0.99 1400 1400 1100 13001.00 - 1.00 1475 1475 1100 13001.01 - 1.10 1475 1475 1175 14001.11 - 1.20 1475 1475 1200 14001.21 - 2.00 1475 1475 1200 1475


Co

ld R

olle

d P

rod

uct

s


Ava

ilab

le S

izes


Notes1- The minimum width is 700 mm.2- Length: min. 914 mm, max. 4880 mm.3- Maximum bundle weight for products in form of sheet is 6 t.4- Coil weights are subject to negotiation.

CCRF Cold rolled, not annealed (full-hard) coil, produced in cold rolling mill no. 2

CCRFS Cold rolled, not annealed (full-hard) sheet cut from coil, produced in cold rolling mill no. 2



0.40 - 0.49 1300 1000 900 10000.50 - 0.50 1300 1000 900 10000.51 - 0.60 1300 1100 900 10000.61 - 0.70 1400 1200 900 11000.71 - 0.75 1400 1300 900 12000.76 - 0.80 1507 1300 900 12000.81 - 0.90 1507 1300 1000 13000.91 - 0.99 1507 1400 1100 13001.00 - 1.00 1507 1400 1100 13001.01 - 1.20 1507 1507 1205 14001.21 - 2.00 1507 1507 1205 1505

GradesGroup Code GradesA 1110, 6106, 6108, 6112, 6113, 7111, 7512, 7513, 7608, 7612B 7022, 7114, 7115, 7116, 7122, 7123, 7124, 7314, 7315, 7316, 7514, 7726C 7125, 7128, 7132, 7136, 7140, 7660D 4137, 5105, 6110, 6137

Co

ld R

olle

d P

rod

uct

s

156

Tolerances

Width ToleranceWidth (mm)

Thickness (mm) w<125 mm 125≤w<250 250≤w<400 400≤w<600 600≤w≤1200 1200<w≤1500Min Max Min Max Min Max Min Max Min Max Min Max

0.59 and thin 0 + 0.4 0 + 0.5 0 + 0.7 0 + 1.0 0 + 4 0 + 50.60 - 0.99 0 + 0.5 0 + 0.6 0 + 0.9 0 + 1.2 0 + 4 0 + 51.00 - 1.99 0 + 0.6 0 + 0.8 0 + 1.1 0 + 1.4 0 + 4 0 + 52.00 0 + 0.7 0 + 1.0 0 + 1.3 0 + 1.6 0 + 4 0 + 5

Notes1- Width is measured perpendicularly to the longitudinal axis of the product.

DIN EN 10131 - 1992Symbols Of Products Covered By This Standard: CR, CCR, ICCR, CRS, CCRS, CRF, CRFS, CCRF, CCRFS, CRK, CCRK,CRSK, CCRSK, CRD, CCRD

Thickness Tolerance (Yield Strength (Re), Width (w) and Thickness)

Thickness (mm) Re < 280 N/mm2 280 ≤ Re < 360 Re ≥ 360w≤1200 mm 1200<w≤1500 w≤1200 1200<w≤1500 w≤1200 1200<w≤1500

0.35 - 0.40 ± 0.04 ± 0.05 ± 0.05 ± 0.06 ± 0.06 ± 0.070.41 - 0.60 ± 0.05 ± 0.06 ± 0.06 ± 0.07 ± 0.07 ± 0.080.61 - 0.80 ± 0.06 ± 0.07 ± 0.07 ± 0.08 ± 0.08 ± 0.100.81 - 1.00 ± 0.07 ± 0.08 ± 0.08 ± 0.10 ± 0.10 ± 0.111.01 - 1.20 ± 0.08 ± 0.09 ± 0.10 ± 0.11 ± 0.11 ± 0.131.21 - 1.60 ± 0.10 ± 0.11 ± 0.12 ± 0.13 ± 0.14 ± 0.151.61 - 2.00 ± 0.12 ± 0.13 ± 0.14 ± 0.16 ± 0.17 ± 0.18

Notes1- Thickness shall be measured at any point located more than 40 mm from the edge.2- For wide strip and slit wide strip, the thickness tolerances in the region of cold rolled welds may be increased by a maximum of 60 % over a

length of 15 mm.

Co

ld R

olle

d P

rod

uct

s


To

lera

nce

s


Notes1- Length is measured along one of the long sides of the sheet or cut length. 2- The edges of cold rolled products have been cut before cold rolling. At the time of the enquiry and order it may be agreed on that the edges

of the sheet products (CRS , CCRS) except for “Full - hard” products which are not annealed shall be cut second time after cold rolling.

Length Tolerance Tolerance (mm)

Length (mm) Lower Upper< 2000 0 + 6≥ 2000 0 + 0.003 x Length

Flatness Tolerance Width (mm) Re < 280 N/mm2 280 ≤ Re < 360

t<0.7 mm 0.7≤t<1.2 ≥ 1.2 t<0.7 mm 0.7≤t<1.2 ≥ 1.2600 - 1199 12 10 8 15 13 101200 - 1499 15 12 10 18 15 131500 and wide 19 17 15 22 20 19

Notes1- Deviation from flatness shall be determined by measuring the deviation in distance between the product and a flat horizontal

surface on which the sheet is placed. 2- The tolerances for flatness given in table above (sheet products with high yield strength) apply for grades 250, 251, 260,

5155, 7128, 7132, 7136, 7140, 7660, 9160. 3- The tolerances on flatness are not applied for the sheet products which are full-hard in the designations of CRFS, CCRFS.

Notes1- Edge camber “q” is the maximum distance between a longitudinal edge and a straight edge supported on the latter. 2- Edge camber shall be measured on the concave edge of the product. 3- The basis of measurement shall be a distance of 2 m taken at any point on the edge.

Co

ld R

olle

d P

rod

uct

s

158

Tolerances On Out Of Squareness

q: Edge camber

u: Out of squareness

Notes1- The out-of-squareness “u” is the orthogonal projection of a transverse edge over a longitudinal edge. 2- The out-of-squareness shall not exceed 1% of the actual width of the sheet.

Tolerances For Edge Camber Type of Product Width (mm) Length (mm) Gauge Length (mm) Tolerance (mm)

Sheet (Cut Length)≥ 600 ≥ 2000 2000 6≥ 600 < 2000 Actual Length (L) + 0.003 x L

Coil (Strip) ≥ 600 - 2000 6Slitted Strip < 600 - 2000 2

DIN EN 10131 - 1992

Co

ld R

olle

d P

rod

uct

s


Pac

kag

ing


CR Cold rolled, batch annealed coilCRK Cold rolled, batch annealed coil with trimmed edge CRF Cold rolled, not annealed (full-hard) coil, produced in cold rolling mill no.1ICCR Cold rolled, continuously annealed thin coilCCR Cold rolled, continuously annealed coilCCRK Cold rolled, continuously annealed coil with trimmed edgeCCRF Cold rolled, not annealed (full-hard) coil, produced in cold rolling mill no. 2

Cold Rolled (Continuously or Batch Annealed) Coil Products

Overseas Shipment

Packaging

• PE waterproof paper.• 2 inside edge protection rings.• 2 outside edge protection rings.• 2 circumferential straps.• 4 radial staps.

• PE waterproof paper.• 2 inside edge protection rings.• 2 outside edge protection rings.• 2 side protection disks.• Inside protection cover (galvanized sheet).• Outside protection cover (galvanized sheet).• 3 circumferential straps.• 4 radial staps.

Co

ld R

olle

d P

rod

uct

s

160

Cold Rolled (Continuously or Batch Annealed) Sheet Products

CRS Cold rolled, batch annealed sheet cut from coilCCRS Cold rolled, continuously annealed sheet cut from coilCRFS Cold rolled, not annealed (full-hard) sheet cut from coil, produced in cold rolling mill no.1CCRFS Cold rolled, not annealed (full-hard) sheet cut from coil, produced in cold rolling mill no. 2CCRSK Cold rolled, continuously annealed sheet cut from coil with trimmed edgeCRSK Cold rolled, batch annealed sheet cut from coil with trimmed edge

Overseas Shipment

• Wooden pallet• PE waterproof paper and with strapping.

• Wooden pallet• PE waterproof paper• Galvanized metal cover and strapping

Co

ld R

olle

d P

rod

uct

s


Pac

kag

ing


CCRD Cold rolled, continuously annealed, slitted coil

Cold (Continuously or Batch Annealed) Rolled Slitted Coil Products

CRD Cold rolled, batch annealed, slitted coil


• Cartoon placed between bands • Wrapping of bands with PE

waterproof paper.• Final strapping of bands with

wooden pallet.


• Wrapping of bands with PEwaterproof paper.


162

Galvanized/Galvannealed Flat Steel Products



166 > Grade Index168 > Steel Grades187 > Available Sizes192 > Tolerances196 > Packaging

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

164

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

165


www.erdemir.com.tr

Galvanized/Galvannealed Flat Steel Products

• Corrosion Resistance: Zincprotects the base metal by providing a barrier to corrosiveelements so that presents anexcellent corrosion resistance.Ultimate service life depends oncoating thickness and the severity of the environment (humidity, salty). • Excellent Surface Appearance: TheC surface quality can be applied toexposed parts without any difficulty. • Formability: Galvanized steels can be used in applications thatrequire deep drawing and bendingoperations. • Paintability: These steels arepaintable if proper pre-treatment(degreasing, surface treatment) is provided.

• Weldability: These steels can bewelded with most of the weldingprocesses. Galvannealed steels have improved spot weldability.

General Applications AreasThe use of galvanized/galvannealedproducts in the automotive industry is growing over the years because of the requirements for improvedcorrosion resistance and paintadherence. Most automotivemanufacturers use galvanizedproducts for both exterior and interiorparts, enabling them to guarantee upto life-time warranty againstcorrosion. Hot dip galvanized steelsare used for various components ofthe car body.

Structural hot dipgalvanized/galvannealed steels areused for a wide range of applicationsin the building sector. Depending onthe atmospheric conditions and thedesired corrosion resistance, thesteels which need different coatingthicknesses are mainly used incladding, roofs, doors, fences,profiling and components foragricultural machinery applications.

The galvanized steels which havebeen used for non-visible parts indomestic appliances are alsopreferable for visible parts in recenttimes. Therefore the steel materialsused for domestic appliances aremainly galvanized steels.

Hot dip galvanized steels are continuously coated on both sides with a zinc layer by means ofa continuous hot dip galvanizing process. After zinc layer created if induction heating is usedto alloy the zinc coating with the steel to create a zinc-iron coating, the product is galvannealedsteel. Cold forming and deep drawing grades, structural steels and high strength and low alloysteels can be coated with zinc/zinc-iron alloys. Galvanized/galvannealed steels are passivatedwith chromating or oiling to preserve the coating against corrosion. These products have threedifferent surface qualities A, B, and C. Surface qualities B and C are produced by skin passand C surface quality is the excellent surface.

Advantages

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

166

Grade Index

Application Areas and Brand Correspondence of Galvanized/Galvannealed Products

General Characteristics Erdemir Steel Corresponding

And Major Applications Standard GradeGrade

1311 DIN EN 10327-04 DX51 D + Z1312 DIN EN 10327-04 DX52 D + Z1313 DIN EN 10327-04 DX53 D + Z

Continuously hot-dip zinc coated 1314 DIN EN 10327-04 DX54 D + Z(galvanized) low carbon steel for cold forming 1315 DIN EN 10327-04 DX56 D + Z

311 A2DC05-Erdemir FR02 311312 XE-Erdemir RN04 312323 A3 DC06-Erdemir FR03 323324 XES-Erdemir RN05 324

1411 DIN EN 10327-04 DX51 D + ZF1412 DIN EN 10327-04 DX52 D + ZF1413 DIN EN 10327-04 DX53 D + ZF

Continuously hot-dip zinc-iron alloy coated1414 DIN EN 10327-04 DX54 D + ZF

(galvannealed) low carbon steel for cold forming1415 DIN EN 10327-04 DX56 D + ZF410 SCGA 270C-Erdemir TY05 410411 SCGA 270C-Erdemir TY06 411430 SCGA 270D-Erdemir TY07 430431 SCGA 270D-Erdemir TY08 431

1118 DIN EN 10292-05 HC180BD + Z1122 DIN EN 10292-05 HC220BD + Z

Continuously hot-dip zinc coated1124 A7-Erdemir FR10 1124

(galvanized) bake-hardening steel1126 DIN EN 10292-05 HC260BD + Z1130 DIN EN 10292-05 HC300BD + Z1218 DIN EN 10292-05 HC180BD + ZF

Continuously hot-dip zinc-iron alloy coated1222 DIN EN 10292-05 HC220BD + ZF

(galvannealed) bake-hardening steel1226 DIN EN 10292-05 HC260BD + ZF1230 DIN EN 10292-05 HC300BD + ZF482 SCGA 340BH-Erdemir TY09 482

Continuously hot-dip zinc coated (galvanized) rephosphorised steel 1522 DIN EN 10292-05 HC220PD + ZContinuously hot-dip zinc coated (galvanized) dual-phase steelwith higher yield strength for cold forming

1660 Erdemir-06 1660

1322 DIN EN 10326-04 S220GD + Z1325 DIN EN 10326-04 S250GD + Z1328 DIN EN 10326-04 S280GD + Z

Continuously hot-dip zinc coated1332 DIN EN 10326-04 S320GD + Z

(galvanized) structural steel1335 DIN EN 10326-04 S350GD + Z355 F1 Gr. 250-Erdemir FR04 355366 XE-320D-Erdemir RN06 366367 F1 Gr. 300-Erdemir FR05 367372 XE-360D-Erdemir RN07 372

1422 DIN EN 10326-04 S220GD + ZF

Continuously hot-dip zinc-iron alloy coated1425 DIN EN 10326-04 S250GD + ZF

(galvannealed) structural steel 1428 DIN EN 10326-04 S280GD + ZF1432 DIN EN 10326-04 S320GD + ZF1435 DIN EN 10326-04 S350GD + ZF


Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

05

Gra

de

Ind

ex

167


www.erdemir.com.tr


Page Material Number Previous EN USA JIS Number

1.0226 DIN EN 10142 Fe PO2 G Z DX51 D + Z ASTM A653 CS Type C JIS 3302 (1987) SGCC 1681.0350 DIN EN 10142 Fe PO3 G Z DX52 D + Z ASTM A653 CS Type B JIS 3302 (1987) SG CD1 1681.0355 DIN EN 10142 Fe PO5 G Z DX53 D + Z ASTM A653 FS Type B JIS 3302 (1987) SG CD2 1681.0306 DIN EN 10142 Fe PO6 G Z DX54 D + Z ASTM A653 DDS Type A JIS 3302 (1987) SG CD3 1681.0322 DIN EN 10142 Fe PO7 G Z DX56 D + Z ASTM A653 EDDS - 168

DIN EN 10142 Fe PO6 G Z DX54 D + Z - - 170DIN EN 10142 Fe PO5 G Z DX53 D + Z ASTM A653(97) FS - 170DIN EN 10142 Fe PO7 G Z DX56 D + Z - - 170DIN EN 10142 Fe PO6 G Z DX54 D + Z - - 170

1.0226 DIN EN 10142 Fe PO2 G ZF DX51 D + ZF ASTM A653 CS Type C JIS 3302 (1987) SGCC 1711.0350 DIN EN 10142 Fe PO3 G ZF DX52 D + ZF ASTM A653 CS Type B JIS 3302 (1987) SG CD1 1711.0355 DIN EN 10142 Fe PO5 G ZF DX53 D + ZF ASTM A653 FS Type B JIS 3302 (1987) SG CD2 1711.0306 DIN EN 10142 Fe PO6 G ZF DX54 D + ZF ASTM A653 DDS Type A JIS 3302 (1987) SG CD3 1711.0322 DIN EN 10142 Fe PO7 G ZF DX56 D + ZF ASTM A653 EDDS - 171

DIN EN 10142 Fe PO5 G ZF DX53 D + ZF ASTM A653 DQ - 172DIN EN 10142 Fe PO5 G ZF DX53 D + ZF ASTM A653 DQ - 172DIN EN 10142 Fe PO7 G ZF DX56 D + ZF - - 172DIN EN 10142 Fe PO7 G ZF DX56 D + ZF - - 172

1.0354 ASTM A653 BHS Gr.180 1771.0356 ASTM A653 BHS Gr.210 177

ASTM A653 BHS Gr.240 1801.0433 ASTM A653 BHS Gr.280 1771.0445 ASTM A653 BHS Gr.300 1771.0354 ASTM A653 BHS Gr.180 1811.0356 ASTM A653 BHS Gr.210 1811.0433 ASTM A653 BHS Gr.280 1811.0445 ASTM A653 BHS Gr.300 181

182ASTM A653 SHS Gr.210 183

185

1.0241 DIN EN 10147 Fe E 220 G Z S220GD + Z ASTM A653 SS Gr.230 - 1731.0242 DIN EN 10147 Fe E 250 G Z S250GD + Z ASTM A653 SS Gr.255 JIS SGC 340 1731.0244 DIN EN 10147 Fe E 280 G Z S280GD + Z ASTM A653 SS Gr.275 JIS SGC 400 1731.0250 DIN EN 10147 Fe E 320 G Z S320GD + Z ASTM A653 HSLAS Gr.340 JIS SGC 440 1731.0529 DIN EN 10147 Fe E 350 G Z S350GD + Z ASTM A653 HSLAS Gr.380 Class 2 JIS SGC 490 173

DIN EN 10147 Fe E 280 G Z S250GD + Z 175DIN EN 10147 Fe E 320 G Z S320GD + Z 175DIN EN 10147 Fe E 320 G Z S320GD + Z 175DIN EN 10147 Fe E 350 G Z S350GD + Z 175

1.0241 DIN EN 10147 Fe E 220 G ZF S220GD + ZF ASTM A653 SS Gr.230 - 1761.0242 DIN EN 10147 Fe E 250 G ZF S250GD + ZF ASTM A653 SS Gr.255 JIS SGC 340 1761.0244 DIN EN 10147 Fe E 280 G ZF S280GD + ZF ASTM A653 SS Gr.275 JIS SGC 400 1761.0250 DIN EN 10147 Fe E 320 G ZF S320GD + ZF ASTM A653 HSLAS Gr.340 JIS SGC 440 1761.0529 DIN EN 10147 Fe E 350 G Z F S350GD + ZF ASTM A653 HSLAS Gr.380 Class 2 JIS SGC 490 176

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

168

Steel Grades

Continuously Hot-Dip Zinc Coated (galvanized) Low Carbon Steel For Cold FormingStandard: DIN EN 10327 - 2004



Notes1- The values for tensile test apply to “Transverse” test pieces.2- For product thicknesses 0.50 mm < d ≤ 0.70 mm (including zinc coating), the minimum elongation values (A80) shall be reduced by 2

units. For d ≤ 0.50 mm this reduction shall be 4 units.3- The value for the yield strength applies to skin-passed products only (surface qualities B and C).4- Products of surface qualities B and C (skin-passed products) are free from stretcher strains for the periods given in the table.5- For product thicknesses greater than 1.5 mm, the r90 value shall be reduced by 0.2.

Erdemir Corresponding Steel New Previously Chemical C Si Mn P S TiGrade Standard Grade DIN EN 10142-91 Limits max. max. max. max. max. max.

1311 DIN EN 10327 DX51D + Z Fe P02 G ZStandard 0.12 0.50 0.60 0.10 0.045 0.30Erdemir 0.08 0.04 0.50 0.03 0.030 0.10




1315 DIN EN 10327 DX56D + Z -Standard 0.12 0.50 0.60 0.10 0.045 0.30Erdemir 0.01 0.04 0.25 0.02 0.015 0.20

ErdemirValidity of Products Re / Rp0.2 Rm

(1) A80 (2) r90 n90

SteelCorresponding Formation N/mm2 N/mm2 (%)

GradeNew Previously Mechanical of Stretcher (kg/mm2) (kg/mm2)Standard Grade DIN EN 10142-91 Properties Strains(4) min. min. min.

1311 DIN EN 10327 DX51D + Z Fe P02 G Z 1 Month 1 Month - 270 - 500 22 - -(27.6 - 51.0)

1312(3) DIN EN 10327 DX52D + Z Fe P03 G Z 1 Month 1 Month 140 - 300 270 - 420 26 - -(14.3 - 30.6) (27.6 - 42.8)

1313 DIN EN 10327 DX53D + Z Fe P05 G Z 6 Month 6 Month 140 - 260 270 - 380 30 - -(14.3 - 26.5) (27.6 - 38.7)

1314 DIN EN 10327 DX54D + Z Fe P06 G Z 6 Month 6 Month 120 - 220 260 - 350 36 1.6 0.18(12.2 - 22.4) (26.5 - 35.7)

1315 DIN EN 10327 DX56D + Z - 6 Month 6 Month 120 - 180 260 - 350 39 1.9 (5) 0.21(12.2 - 18.4) (26.5 - 35.7)

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

www.erdemir.com.tr

Ste

el G

rad

es

169


Coating Requirements For Low Carbon Steel Galvanized With Zinc Coating

Coating Requirements For Low Carbon Steel Galvannealed With Zinc-‹ron Alloy Coating

Notes1- Orders for other coating masses are subject to agreement.

Notes1- Orders are subject to agreement.2- Orders for grades 1313, 1314, 1315 are subject to agreement.3- Surface quality A is available on agreement.4- Surface qualities A, B and C are available on agreement.5- Orders for other coating masses are subject to agreement

Minimum Coating Coating Surface QualityMass Mass

Erdemir (Including Both Surfaces)(5) (g/m2)Steel (g/m2) Triple SingleGrade spot test spot test Coating Finish with Minimized Spangle

100 100 85 A, B, C140 140 120 A, B, C200 200 170 A, B, C

1311 225 (1) 225 195 A, B, C (4)

275 275 235 A, B, C350 350 300 A (3)

450 (1) 450 385 A (3)

1312100 100 85 A, B, C

1313140 140 120 A, B, C

1314200 200 170 A, B, C

1315225 (1) 225 195 A, B, C (4)

275 (2) 275 235 A, B, C (4)

Coating Minimum Surface QualityErdemir Mass Coating MassSteel (Includ›ng Both Surfaces) (g/m2)Grade (g/m2) Triple Single Coating Finish with Regular

spot test spot test Zinc-Iron Alloy Coating 1411

100 100 85 A, B, C141214131414

120 120 100 A, B, C1415

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

170

Notes1- The values for the tensile test apply to “Transverse” test pieces.2- Surface roughness for products of grades 312, 324 is in the range of 0.70 - 1.30 µm.3- Surface roughness for products of grades 311, 323 is in the range of 1.00 - 1.70 µm.4- The value for y›eld stress is increased by 20 N/mm2 (2,0 kg/mm2) for thickness greater than 0.5 mm and less than or equal to 0.7 mm.

For thickness less than or equal to 0.5 mm, the value is increased by 40 N/mm2 (4,1 kg/mm2).5- The values of r90 and n90 only apply to products of thickness greater than 0.5 mm.



Continuously Hot-Dip Zinc Coated (galvanized) Low Carbon Steel For Cold Forming

Erdemir Corresponding Steel User Applied Similar C Mn P S Ti NbGrade Sector Standard Standard max. max. max. max. max. max.

311 Automotive A2 DC05-Erdemir FR02 DIN EN 10327 DX54D +Z 0.004 0.20 0.015 0.010 0.07 0.03312 Automotive XE-Erdemir RN04 DIN EN 10327 DX53D +Z 0.050 0.25 0.020 0.015 0.03 0.01323 Automotive A3 DC06-Erdemir FR03 DIN EN 10327 DX56D +Z 0.004 0.15 0.010 0.010 0.06 0.03324 Automotive XES-Erdemir RN05 DIN EN 10327 DX54D +Z 0.005 0.25 0.015 0.015 0.07 0.03

Re Rm(1) A80 r90 n90Erdemir

Corresponding N/mm2 N/mm2 (%)SteelUser Applied Similar (kg/mm2) (kg/mm2)Grade

Sector Standard Standard min. min. min.

311(2) (3) Automotive A2 DC05-Erdemir FR05 DIN EN 10327 DX54D +Z140 - 180 270 - 330 38 1.80 (4) 0.20 (4)

(14.3 - 18.4) (27.6 - 33.7)

312(2) Automotive XE-Erdemir RN04 DIN EN 10327 DX53D +Z180 - 230 300 - 370 34 - -

(18.4 - 23.5) (30.6 - 37.7)

323(2) (3) Automotive A3 DC06-Erdemir FR03 DIN EN 10327 DX56D +Z120 - 165 270 - 350 40 2.10 (4) 0.22 (4)

(12.2 - 16.8) (27.6 - 35.7)

324(2) Automotive XES-Erdemir RN05 DIN EN 10327 DX54D +Z160 - 200 280 - 350 37 1.80 0.19

(16.3 - 20.4) (28.6 - 35.7)

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

www.erdemir.com.tr

Ste

el G

rad

es

171


Continuously Hot-Dip Zinc-Iron Alloy Coated (galvannealed) Low Carbon Steel For Cold FormingStandard: DIN EN 10327 - 2004



Notes1- The values for tensile test apply to “Transverse” test pieces.2- For product thicknesses 0.50 mm < d ≤ 0.70 mm (including zinc coating), the minimum elongation values (A80) shall be reduced by 2

units. For d ≤ 0.50 mm this reduction shall be 4 units.3- The value for the yield strength applies to skin-passed products only (surface qualities B and C).4- Products of surface qualities B and C (skin-passed products) are free from stretcher strains for the periods given in the table.5- For product thicknesses greater than 1.5 mm, the minimum r90 value shall be reduced by 0.2.6- For product thicknesses equal to or less than 0.7 mm, the r90 value shall be reduced by 0.2 and the n90 value by 0.01.

Erdemir Corresponding Steel New Previously Chemical C Si Mn P S TiGrade Standard Grade DIN EN 10142-91 Limits max. max. max. max. max. max.

1411 DIN EN 10327 DX51D + ZF Fe P02 G ZFStandard 0.12 0.50 0.60 0.10 0.045 0.30Erdemir 0.08 0.04 0.50 0.03 0.030 0.10




1415 DIN EN 10327 DX56D + ZF -Standard 0.12 0.50 0.60 0.10 0.045 0.30Erdemir 0.01 0.04 0.25 0.02 0.015 0.20

ErdemirValidity of Products Re / Rp0.2 Rm

(1) A80(2) r90 n90

SteelCorresponding Formation N/mm2 N/mm2 (%)

GradeNew Previously Mechanical of Stretcher (kg/mm2) (kg/mm2)Standard Grade DIN EN 10142-91 Properties Strains(4) min. min. min.

1411 DIN EN 10327 DX51D + ZF Fe P02 G ZF 1 Month 1 Month -270 - 500 22 - -

(27.6 - 51.0)

1412 (3) DIN EN 10327 DX52D + ZF Fe P03 G ZF 1 Month 1 Month140 - 300 270 - 420 26 - -

(14.3 - 30.6) (27.6 - 42.8)

1413 DIN EN 10327 DX53D + ZF Fe P05 G ZF 6 Month 6 Month140 - 260 270 - 380 30 - -

(14.3 - 26.5) (27.6 - 38.7)

1414 DIN EN 10327 DX54D + ZF Fe P06 G ZF 6 Month 6 Month120 - 220 260 - 350 34 1.4 0.18

(12.2 - 22.4) (26.5 - 35.7)

1415 DIN EN 10327 DX56D + ZF - 6 Month 6 Month120 - 180 260 - 350 37 1.7 (5) (6) 0.20 (6)

(12.2 - 18.4) (26.5 - 35.7)

Re Rm(1) A80 r nErdemir

Corresponding N/mm2 N/mm2 (%)SteelUser Applied Similar (kg/mm2) (kg/mm2)Grade

Sector Standard Standard min. min. max. min. min.

410 (2) Automotive SCGA 270C-Erdemir TY05 DIN EN 10327 DX53D + ZF180 - 235 270 36 43 - -

(18.4 - 24.0) (27.6)

411 (2) Automotive SCGA 270C-Erdemir TY06 DIN EN 10327 DX53D + ZF180 - 235 270 39 46 - -

(18.4 - 24.0) (27.6)

430 (2) Automotive SCGA 270D-Erdemir TY07 DIN EN 10327 DX56D + ZF140 - 180 270 41 47 1.40 0.20

(14.3 - 18.4) (27.6)

431 (2) Automotive SCGA 270D-Erdemir TY08 DIN EN 10327 DX56D + ZF140 - 180 270 44 51 1.40 0.20

(14.3 - 18.4) (27.6)


Notes1- The values for the tensile test apply to “Transverse” test pieces.2- Surface roughness for products of grades 410, 411, 430, 431 is in the range of 0.70 - 1.30 µm.

Notes1- The values for all mechanical tests of grades 410, 430 are applicable for thickness greater than or equal to 0.40 mm and less than 1.00 mm.2- The values for all mechanical tests of grade 411 are applicable for thickness greater than or equal to 1.00 mm and less than 1.60 mm.3- The values for all mechanical tests of grade 431 are applicable for thickness greater than or equal to 1.00 mm and less than 2.00 mm.


Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

10 172

Continuously Hot-Dip Zinc-Iron Alloy Coated (galvannealed) Low Carbon Steel For Cold Forming

Erdemir Corresponding Steel User Applied Similar C Mn P S Ti NbGrade Sector Standard Standard max. max. max. max. max. max.

410 (1) Automotive SCGA 270C-Erdemir TY05 DIN EN 10327 DX53D + ZF 0.050 0.25 0.020 0.015 0.01 0.01411 (1) Automotive SCGA 270C-Erdemir TY06 DIN EN 10327 DX53D + ZF 0.050 0.25 0.020 0.015 0.01 0.01430 (1) Automotive SCGA 270D-Erdemir TY07 DIN EN 10327 DX56D + ZF 0.004 0.20 0.010 0.010 0.06 0.03431 (1) Automotive SCGA 270D-Erdemir TY08 DIN EN 10327 DX56D + ZF 0.004 0.20 0.010 0.010 0.06 0.03

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

11

Ste

el G

rad

es

173


www.erdemir.com.tr

Continuously Hot-Dip Zinc Coated (galvanized) Structural SteelStandard: DIN EN 10326 - 2004



Notes1- The values for tensile test apply to “Longitudinal” test pieces.2- For product thicknesses equal to or less than 0.7 mm (including zinc coating), the minimum elongation values shall be reduced by 2 units.3- The values of tensile strength for all the steel grades may be expected to be within a value range of 140 N/mm2 (14.3 kg/mm2).

Erdemir Corresponding Steel New Previously Chemical C Si Mn P SGrade Standard Grade DIN EN 10147-91 Limits max. max. max. max. max.

1322 DIN EN 10326 S220GD + Z Fe E 220 G ZStandard 0.20 0.60 1.70 0.10 0.045Erdemir 0.12 0.10 0.90 0.03 0.030





ErdemirRe / Rp0.2 Rm

(1) (3) A80(2)

SteelCorresponding N/mm2 N/mm2 (%)

GradeNew Previously (kg/mm2) (kg/mm2)Standard Grade DIN EN 10147-91 min. min. min.

1322 DIN EN 10326 S220GD + Z Fe E 220 G Z220 300 20

(22.4) (30.6)

1325 DIN EN 10326 S250GD + Z Fe E 250 G Z250 330 19

(25.5) (33.6)

1328 DIN EN 10326 S280GD + Z Fe E 280 G Z280 360 18

(28.6) (36.7)

1332 DIN EN 10326 S320GD + Z Fe E 320 G Z320 390 17

(32.6) (39.8)

1335 DIN EN 10326 S350GD + Z Fe E 350 G Z350 420 16

(35.7) (42.8)

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

174

Coating Requirements For Structural Steel Galvanized With Zinc Coating

(4)Coating Minimum Surface QualityMass Coating Mass

Erdemir (Including Both Surfaces) (g/m2)Steel (g/m2) Triple SingleGrade spot test spot test Coating Finish with Minimized Spangle

100 100 85 A, B, C1322 140 140 120 A, B, C1325 200 200 170 A, B, C1328 225(1) 225 195 A, B, C (3)

1332 275 275 235 A, B, C1335 350 350 300 A

450(1) 450 385 A (2)

Coating Requirements For Structural Steel Galvannealed With Zinc-Iron Alloy Coating


Notes1- Orders are subject to agreement.2- Surface quality A is available on agreement.3- Surface qualities B and C are available on agreement. 4- Orders for other coating masses are subject to agreement.

Minimum Surface QualityCoating Coating

Erdemir Mass MassSteel (Including Both Surfaces)(1) (g/m2)Grade (g/m2) Triple Single Coating Finish with Regular


100 100 85 A, B, C142514281432 120 120 100 A, B, C1435

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

09

Ste

el G

rad

es

175


www.erdemir.com.tr

Continuously Hot-Dip Zinc Coated (galvanized) Structural Steel


Notes1- The values for the tensile test apply to “Longitudinal” test pieces.2- Surface roughness for products of grades 366, 372 is in the range of 0.70 - 1.30 µm.3- Surface roughness for products of grades 355, 367 is in the range of 1.00 - 1.70 µm.



Erdemir Corresponding Steel User Applied Similar C Mn P S Nb VGrade Sector Standard Standard max. max. max. max. max. max.

355 Automotive F1 Gr. 250-Erdemir FR04 DIN EN 10326 S250GD +Z 0.17 0.90 0.020 0.020 0.02 -366 Automotive XE-320D-Erdemir RN06 DIN EN 10326 S320GD +Z 0.10 0.90 0.020 0.015 0.08 0.07367 Automotive F1 Gr. 300-Erdemir FR05 DIN EN 10326 S280GD +Z 0.10 0.85 0.020 0.015 0.08 0.06372 Automotive XE-360D-Erdemir RN07 DIN EN 10326 S350GD +Z 0.12 1.00 0.020 0.015 0.08 0.08

BendErdemir Re Rm

(1) A50 A80 (Trans., 1800)Steel Corresponding N/mm2 N/mm2 (%) (%) mdbGrade User Applied Similar (kg/mm2) (kg/mm2) (d: Thickness)

Sector Standard Standard min. min. min.

355 (3) Automotive F1 Gr. 250-Erdemir FR04 DIN EN 10326 S250GD +Z250 - 350 350 25 1 d

(25.5 - 35.7) (35.7)

366 (2) Automotive XE-320D-Erdemir RN06 DIN EN 10326 S320GD +Z320 - 380 415 - 480 24 3 d

(32.7 - 38.8) (42.3 - 49.0)

367 (3) Automotive F1 Gr. 300-Erdemir FR05 DIN EN 10326 S280GD +Z300 - 400 400 23 2 d

(30.6 - 40.8) (40.8)

372 (2) Automotive XE-360D-Erdemir RN07 DIN EN 10326 S350GD +Z360 - 430 450 - 530 21 3 d

(36.7 - 43.9) (45.9 - 54.1)

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

176

Continuously Hot-Dip Zinc-Iron Alloy Coated (galvannealed) Structural SteelStandard: DIN EN 10326 - 2004



Notes1- The values for tensile test apply to “Longitudinal” test pieces.2- For product thicknesses equal to or less than 0.7 mm (including zinc coating), the minimum elongation values shall be reduced by 2 units.3- The values of tensile strength for all the steel grades may be expected to be within a value range of 140 N/mm2 (14.3 kg/mm2).

Erdemir Corresponding Steel New Previously Chemical C Si Mn P SGrade Standard Grade DIN EN 10147-91 Limits max. max. max. max. max.

1422 DIN EN 10326 S220GD + ZF Fe E 220 G ZFStandard 0.20 0.60 1.70 0.10 0.045Erdemir 0.12 0.10 0.90 0.03 0.030





Re / Rp0.2 Rm(1) (3) A80

(2)

ErdemirCorresponding N/mm2 N/mm2 (%)

SteelNew Previously (kg/mm2) (kg/mm2)

GradeStandard Grade DIN EN 10147-91 min. min. min.

1422 DIN EN 10326 S220GD + ZF Fe E 220 G ZF220 300 20

(22.4) (30.6)


(25.5) (33.6)


(28.6) (36.7)


(32.6) (39.8)


(35.7) (42.8)

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

www.erdemir.com.tr

Ste

el G

rad

es

177


Continuously Hot-Dip Zinc Coated (galvanized) Bake-Hardening Steel With Higher Yield Strength For Cold Forming Standard: DIN EN 10292 - 2005



Notes1- The values for mechanical test apply to “Transverse” test pieces.2- The mechanical properties are valid for a period of 3 months from the date on which the products are made available.

Notes1- Ti + Nb + V ≤ 0.22%.2- Vanadium and boron may also be added.

ErdemirSteel Corresponding Chemical C Si Mn P S Al Ti (1) Nb (1)

Grade Standard Grade Limits max. max. max. max. max. min. max. max.

1118 DIN EN 10292 HC180BD + ZStandard 0.04 0.50 0.70 0.06 0.025 0.02 - -Erdemir 0.005 0.03 0.20 0.015 0.010 0.02 0.015 0.015




Rp0.2 A80 r90 n90

or Re BH2 Rm(1) (%)Erdemir

N/mm2 N/mm2 N/mm2Steel

Corresponding (kg/mm2) (kg/mm2) (kg/mm2)GradeStandard Grade min. min. min. min.

1118 DIN EN 10292 HC180BD + Z180 - 240 35 300 - 360 34 1.5 0.16

(18.4 - 24.5) (3.6) (30.6 - 36.7)

1122 DIN EN 10292 HC220BD + Z220 - 280 35 340 - 400 32 1.2 0.15

(22.4 - 28.6) (3.6) (34.7 - 40.8)

1126 DIN EN 10292 HC260BD + Z260 - 320 35 360 - 440 28 - -

(26.5 - 32.6) (3.6) (36.7 - 44.9)

1130 DIN EN 10292 HC300BD + Z300 - 360 35 400 - 480 26 - -

(30.6 - 36.7) (3.6) (40.8 - 49.0)

Bend (1)

(Trans., 180o)Erdemir mdbSteel (d: Thickness)Grade d < 1.5 mm d ≥ 1.5 mm

1118, 1218 0 01122, 1222 1 11126, 1226 2 21130, 1230 2 3

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

178

Mandrel Diameter For The Bend Test To Determine The Adhesion Of The Coating For Bake-Hardening Steel

Coating Requirements For Bake-Hardening Steel Galvanized With Zinc Coating

Notes1- For coating thicknesses above 25 µm, the mandrel diameter shall be increased by 1d for all types of hot-dip coatings.

Notes1- Orders for other coating masses are subject to agreement.2- Orders are subject to agreement.3- Surface quality C is available on agreement.


Erdemir Mass MassSteel (Including Both Surfaces)(1) (g/m2)Grade (g/m2) Triple Single

spot test spot test Coating Finish with Minimized Spangle100 100 85 A, B, C

1118 140 140 120 A, B, C1122

200 200 170 A, B, C1126225 (2) 225 195 A, B, C (3)

1130275 (2) 275 235 A, B, C (3)

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

www.erdemir.com.tr

Ste

el G

rad

es

179


Coating Requirements For Bake-Hardening Steel Galvannealed With Zinc-Iron Alloy Coating


Coating Minimum Surface QualityErdemir Mass Coating MassSteel (Includ›ng Both Surfaces) (1) (g/m2)Grade (g/m2) Triple Single Coating Finish with Regular


100 100 85 A, B, C12221226

120 120 100 A, B, C1230

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

180




Notes1- Ti + Nb + V + B ≤ 0.22%.

Continuously Hot-Dip Zinc Coated (galvanized) Bake-Hardening SteelWith Higher Yield Strength For Cold Forming

ErdemirSteel Corresponding C Si Mn P S Al Ti (1) Nb (1)

Grade Standard Grade max. max. max. max. max. min. max. max.1124 A7-Edemir FR10 1124 0.005 0.03 0.55 0.080 0.010 0.02 0.020 0.005

Rp0.2 A80

or Re BH2 Rm(1) (%)Erdemir

N/mm2 N/mm2 N/mm2Steel

Corresponding (kg/mm2) (kg/mm2) (kg/mm2)GradeStandard Grade min. min.

1124 A7-Edemir FR10 1124234 - 280 35 350 - 479 26

(23.9 - 28.6) (3.6) (35.7 - 48.9)

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

www.erdemir.com.tr

Ste

el G

rad

es

181


Continuously Hot-Dip Zinc-Iron Alloy Coated (Galvannealed) Bake-Hardening SteelWith Higher Yield Strength For Cold FormingStandard: DIN EN 10292 - 2005







1218 DIN EN 10292 HC180BD + ZFStandard 0.04 0.50 0.70 0.06 0.025 0.02 - -Erdemir 0.005 0.03 0.20 0.015 0.010 0.02 0.015 0.015




ErdemirRp0.2 A80 r90 n90

Steelor Re BH2 Rm

(1) (%)

GradeN/mm2 N/mm2 N/mm2

Corresponding (kg/mm2) (kg/mm2) (kg/mm2)Standard Grade min. min. min. min.

1218 DIN EN 10292 HC180BD + ZF180 - 240 35 300 - 360 32 1.3 0.16

(18.4 - 24.5) (3.6) (30.6 - 36.7)

1222 DIN EN 10292 HC220BD + ZF220 - 280 35 340 - 400 30 1.0 0.15

(22.4 - 28.6) (3.6) (34.7 - 40.8)

1226 DIN EN 10292 HC260BD + ZF260 - 320 35 360 - 440 26 - -

(26.5 - 32.6) (3.6) (36.7 - 44.9)

1230 DIN EN 10292 HC300BD + ZF300 - 360 35 400 - 480 24 - -

(30.6 - 36.7) (3.6) (40.8 - 49.0)

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

182



Notes1- The values for all mechanical tests of grade 482 are applicable for thickness of 0.70 mm.

Notes1- The values for the tensile test apply to “Transverse” test pieces.2- Surface roughness for product of grade 482 is in the range of 0.70 - 1.30 µm.

Continuously Hot-Dip Zinc-Iron Alloy Coated (galvannealed) Bake-Hardening Steel With Higher Yield Strength For Cold FormingStandard: Erdemir

Erdemir Corresponding Steel User Applied Similar C Mn P S Ti NbGrade Sector Standard Standard max. max. max. max. max. max.482 (1) Automotive SCGA340 BH-Erdemir TY09 DIN EN 10292 H220BD +ZF 0.005 0.70 0.080 0.015 0.03 0.03

Re Rm(1) A80 BH2 r n90

Erdemir Corresponding N/mm2 N/mm2 (%) N/mm2

Steel User Applied Similar (kg/mm2) (kg/mm2) (kg/mm2)Grade Sector Standard Standard min. min. max. min. min. min.

482 (2) Automotive SCGA340 BH-Erdemir TY09 DIN EN 10292 H220BD +ZF195 - 295 340 34 41 30 1.40 0.15(19.9 - 30.1) (34.7) (3.1)

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

www.erdemir.com.tr

Ste

el G

rad

es

183


Continuously Hot-Dip Zinc Coated (galvanized) Rephosphorized SteelWith Higher Yield Strength For Cold FormingStandard: DIN EN 10292 - 2005



1522 DIN EN 10292 HC220PD + ZStandard 0.06 0.50 0.70 0.08 0.025 0.02 - -Erdemir 0.01 0.10 0.60 0.06 0.015 0.02 0.03 0.03





Rp0.2 A80 r90 n90

Erdemir or Re Rm(1) (%)

Steel N/mm2 N/mm2

Grade Corresponding (kg/mm2) (kg/mm2)Standard Grade min. min. min.

1522 DIN EN 10292 HC220PD + Z220 - 280 340 - 400 32 1.3 0.15

(22.4 - 28.6) (34.7 - 40.8)

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

184

Coating Requirements For Rephosphorized Steel Galvanized With Zinc Coating

Notes1- Orders for other coating masses are subject to agreement.2- Orders are subject to agreement.3- Surface quality C is available on agreement.

Mandrel Diameter For The Bend Test To Determine The Adhesion Of The Coating ForRephosphorized Steel

Notes1- For coating thicknesses above 25 µm, the mandrel diameter shall be increased by 1d for all types of hot-dip coatings.

Thickness (1)

(Trans., 180o)ErdemirmdbSteel

(d: Thickness)Graded < 1.5 mm d≥ 1.5 mm

1522 1 1


Erdemir Mass MassSteel (Including Both Surfaces)(1) (g/m2)Grade (g/m2) Triple Single Coating Finish with

spot test spot test Minimized Spangle100 100 85 A, B, C140 140 120 A, B, C

1522 200 200 170 A, B, C225 (2) 225 195 A, B, C (3)

275 (2) 275 235 A, B, C (3)

ErdemirSteel Corresponding Chemical C Si Mn P S Al Cr NbGrade Standard Grade Limits max. max. max. max. max. min. max. max.

1660 Erdemir-2006 1660Standard 0.11 0.25 1.60 0.06 0.010 0.02 0.80 -Erdemir 0.11 0.25 1.30 0.06 0.010 0.02 0.80 0.01

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

www.erdemir.com.tr

Ste

el G

rad

es

185




Notes1- The values for mechanical test apply to “Longitudinal” test pieces.2- The mechanical properties are valid for a period of 3 months from the date on which the products are made available. 3 - The bend test is carried only when specified at the time of the enquiry and order.

Continuously Hot-Dip Zinc Coated (galvanized) Dual-Phase Steel With Higher Yield Strength For Cold FormingStandard: Erdemir

Rp0.2 BH2 Rm A80

Erdemir or Re (%) Bend (3)

Steel N/mm2 N/mm2 N/mm2 (Trans., 90o)Grade Corresponding (kg/mm2) (kg/mm2) (kg/mm2) mrb

Standard Grade min. min. (d: Thickness)

1660 Erdemir-2006 1660350 - 480 30 600 - 700 16 1 d

(35.7 - 49.0) (3.1) (61.2 - 71.4)

(1)

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

186

Coating Requirements For Dual-Phase Steel Galvanized With Zinc Coating

Notes1- Orders are subject to agreement.2- Surface quality A is available on agreement.3- Surface qualities B and C are available on agreement.4- Orders for other coating masses are subject to agreement.


Erdemir Mass MassSteel (Including Both Surfaces) (4) (g/m2)Grade (g/m2) Triple Single Coating Finish with

spot test spot test Minimized Spangle100 100 85 A, B, C140 140 120 A, B, C200 200 170 A, B, C

1660 225 (1) 225 195 A, B, C (3)

275 275 235 A, B, C350 350 300 A450 (1) 450 385 A (2)


Ava

ilab

le S

izes

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts


Galvanized And Galvannealed Products

Available Sizes


Symbol Min. Max.

GZR 0.30 2.00 Zinc coated, galvanized coil

GZRK 0.30 2.00 Zinc coated, galvanized coil with trimmed edge

GZRD 0.30 2.00 Zinc coated, galvanized, slitted coil

GZRS 0.30 2.00 Zinc coated sheet cut from galvanized coil

GFR 0.30 2.00 Zinc-iron alloy coated, galvannealed coil

GFRK 0.30 2.00 Zinc-iron alloy coated, galvannealed coil with trimmed edge

GFRD 0.30 2.00 Zinc-iron alloy coated, galvannealed, slitted coil

GFRS 0.30 2.00 Zinc-iron alloy coated sheet cut from galvannealed coil

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

188


A 312, 1311, 1312, 1313410, 411, 1411, 1412, 1413

B311, 323, 324, 1118, 1122, 1124, 1126, 1130, 1314, 1315, 1522, 430, 431, 482, 1218, 1222, 1226, 1230, 1414, 1415

C 366, 367, 372, 1332, 1335,1432, 1435, 1660D 355, 1322, 1325,1422, 1425E 1328, 1428

Notes1- The minimum width is 700 mm.2- Length: min. 914 mm, max. 4880 mm.3- For grades 410, 430, orders of thicknesses greater than or equal to 0.40 mm and less than 1.00 mm are accepted.4- For grade 411, orders of thicknesses greater than or equal to 1.00 mm and less than 1.60 mm are accepted.5- For grade 431, orders of thicknesses greater than or equal to 1.00 mm and less than 2.00 mm are accepted.6- For grade 482, orders for products other than product with thickness of 0.70 mm are not accepted.7- In case of sheet, maximum bundle weight for products is 6 t.8- Coil weights are subject to negotiation.9- Order width may change depending on coating weight of the product.

GZR Zinc coated, galvanized coil

GFR Zinc-iron alloy coated, galvannealed coil

GZRS Zinc coated sheet cut from galvanized coil

GFRS Zinc-iron alloy coated sheet cut from galvannealed coil


Thickness (mm) (3) (4) (5) (6) (7)

Group-A Group-B Group-C Group-D0.30 - 0.35 10000.36 - 0.39 11000.40 - 0.50 1300 1000 900 1000 0.51 - 0.60 1300 1100 900 1000 0.61 - 0.70 1400 1200 900 11000.71 - 0.75 1400 1300 900 1200 0.76 - 0.80 1500 1300 900 12000.81 - 0.90 1500 1300 1000 13000.91 - 1.00 1500 1400 1100 13001.01 - 1.20 1500 1500 1200 14001.21 - 2.00 1500 1500 1200 1500


Ava

ilab

le S

izes

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts


Notes1- The minimum width is 700 mm.2- For grades 410, 430, orders of thicknesses greater than or equal to 0.40 mm and less than 1.00 mm are accepted.3- For grade 411, orders of thicknesses greater than or equal to 1.00 mm and less than 1.60 mm are accepted.4- For grade 431, orders of thicknesses greater than or equal to 1.00 mm and less than 2.00 mm are accepted.5- For grade 482, orders for products other than product with thickness of 0.70 mm are not accepted.6- Coil weights are subject to negotiation.7- Order width may change depending on coating weight of the product.

GZRK Zinc coated, galvanized coil with trimmed edge

GFRK Zinc-iron alloy coated, galvannealed coil with trimmed edge


Thickness (mm) (2) (3) (4) (5) (6)

Group-A Group-B Group-C Group-D0.30 - 0.35 10000.36 - 0.39 11000.40 - 0.50 1275 975 875 1000 0.51 - 0.60 1275 1075 875 10000.61 - 0.70 1375 1175 900 1100 0.71 - 0.75 1400 1275 900 1200 0.76 - 0.79 1475 1275 900 1200 0.80 - 0.80 1475 1300 900 1200 0.81 - 0.90 1475 1300 1000 1300 0.91 - 1.00 1475 1400 1100 1300 1.01 - 1.10 1475 1475 1175 1400 1.11 - 1.20 1475 1475 1200 1400 1.21 - 2.00 1475 1475 1200 1475


A 312, 1311, 1312, 1313410, 411, 1411, 1412, 1413

B311, 323, 324, 1118, 1122, 1124, 1126, 1130, 1314, 1315, 1522, 430, 431, 482, 1218, 1222, 1226, 1230, 1414, 1415

C 366, 367, 372, 1332, 1335,1432, 1435, 1660D 355, 1322, 1325, 1422, 1425

E1328, 1428


A1311, 13121411, 1412

B 311, 312, 323, 324, 355, 1118, 1122, 1124, 1126, 1130, 1313, 1314, 1315, 1322, 1325, 1328, 1522, 1660,410, 411, 430, 431, 482, 1218, 1222, 1226, 1230, 1413, 1414, 1415, 1422, 1425, 1428

C 366, 367, 372, 1332, 13351432, 1435

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

190

Notes1- The minimum width is 400 mm.2- For grades 410, 430, orders of thicknesses greater than or equal to 0.40 mm and less than 1.00 mm are accepted.3- For grade 411, orders of thicknesses greater than or equal to 1.00 mm and less than 1.60 mm are accepted.4- For grade 431, orders of thicknesses greater than or equal to 1.00 mm and less than 2.00 mm are accepted.5- For grade 482, orders for products other than product with thickness of 0.70 mm are not accepted.6- For products of thicknesses less than 0.70 mm, order for product of surface quality C is not accepted.

GZRD Zinc coated, galvanized, slitted coil

GFRD Zinc-iron alloy coated, galvannealed, slitted coil


Thickness (mm) (2) (3) (4) (5) (6)

Group-A Group-B Group-C Group-D0.30 - 0.39 6990.40 - 2.00 699 699 699

Grades


Ava

ilab

le S

izes

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts


Table For Acceptable Order Width Depending On Coating Mass

For Galvanized and Galvannealed Products Of Any Order Thickness

Coating Mass Code Total Coating Mass (g/m2) Amount Tobe Subtracted From Nominal Order Thicknes (mm)51 100 0.0152 120 0.0153 140 0.0154 200 0.0255 225 0.0256 275 0.0357 350 0.0458 450 0.0559 500 0.0660 70 061 90 062 80 063 180 0.0264 250 0.0265 300 0.0366 60 067 400 0.0568 75 069 150 0.0170 110 0.01

Example: For grade 1311, suppose that an order for thickness 0.78 mm is given with a coating code (500 g/m2). In this case the actualthickness should be considered 0.72 mm. (0.78 mm - 0.06 mm = 0.72 mm) Then, relative width depending on actual thickness shall be max.1400 mm.

192

Tolerances

DIN EN 10143 - 1993Symbols Of Products Covered By This Standard: GZR, GZRK, GZRD, GZRS, GFR, GFRK, GFRD, GFRSThe standard applies to continiusly hot-dip metal coated flat products with thicknesses equal to or thinner than 3 mm.

Thickness Tolerance

Thickness (mm)Group A Group B

w≤1200 mm 1200<w≤1500 w>1500 w≤1200 mm 1200<w≤1500 w>15000.40 and thin ± 0.05 ± 0.06 - ± 0.06 ± 0.07 -0.41 - 0.60 ± 0.06 ± 0.07 ± 0.08 ± 0.07 ± 0.08 ± 0.090.61 - 0.80 ± 0.07 ± 0.08 ± 0.09 ± 0.08 ± 0.09 ± 0.110.81 - 1.00 ± 0.08 ± 0.09 ± 0.10 ± 0.09 ± 0.11 ± 0.121.01 - 1.20 ± 0.09 ± 0.10 ± 0.11 ± 0.11 ± 0.12 ± 0.131.21 - 1.60 ± 0.11 ± 0.12 ± 0.12 ± 0.13 ± 0.14 ± 0.141.61 - 2.00 ± 0.13 ± 0.14 ± 0.14 ± 0.15 ± 0.17 ± 0.172.01 - 2.50 ± 0.15 ± 0.16 ± 0.16 ± 0.18 ± 0.19 ± 0.192.51 - 3.00 ± 0.17 ± 0.18 ± 0.18 ± 0.20 ± 0.21 ± 0.21

A) The tolerances above in the table shall be applied for hot-dip metal coated flat products made from: Low carbon steels for cold forming (311, 312, 323, 324, 410, 411, 430, 431, 1311, 1312, 1313, 1314, 1315, 1411, 1412, 1413, 1414, 1415)Structural steels with a minimum yield strength (Re) < 280 N/mm2 (355, 1322, 1325, 1422, 1425),Bake-hardening steels with a minimum yield strength (Re) < 280 N/mm2 (482, 1118, 1122, 1124, 1218, 1222),Rephosphorised steels with a minimum yield strength (Re) < 280 N/mm2 (1522),

B) The tolerances above in the table shall be applied for hot-dip metal coatedflat products made from structural steels (366, 367, 372, 1328, 1332, 1335, 1428, 1432, 1435), flat products made from bake-hardening steels (1126, 1130, 1226, 1230) and flat products made from dual-phase steels (1660) with a minimum yield strength (Re) ≥ 280 N/mm2.

Notes1- The thickness shall be measured at any point located more than 40 mm from the edges.2. For wide strip and slit wide strip, the thickness tolerances in the region of cold rolled welds may be increased by a maximum of 60%

over a length of 15 mm.3. In case of 450 g/m2 of coating mass, values of tolerances on thicness are increased by 0.02 mm.

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts


To

lera

nce

sG

alva

niz

ed/G

alva

nn

eale

d P

rod

uct

s


Width Tolerance

a) For width of sheet and wide strip of widths equal to or wider than 600 mm:

Width(mm) Lower Upper600-1200 0 + 51201-1500 0 + 61501 and wide 0 + 7

b) For width of slit wide strip of width less than 600 mm:

Nominal Width Of Slit Wide Strip (mm)Thickness (mm) 124 and narrow 125-249 250-399 400-599

Lower Upper Lower Upper Lower Upper Lower Upper0.59 and thin 0 + 0.4 0 + 0.5 0 + 0.7 0 + 1.00.60-0.99 0 + 0.5 0 + 0.6 0 + 0.9 0 + 1.21.00-1.99 0 + 0.6 0 + 0.8 0 + 1.1 0 + 1.42.00-3.00 0 + 0.7 0 + 1.0 0 + 1.3 0 + 1.6

Notes1- Width is measured perpendicularly to the longitudinal axis of the product.

Length Tolerance Length (mm) Lower Upper1999 and shorter 0 + 62000 and longer 0 + 0.003 x Nominal Length

Notes1- Length is measured along one of the long sides of the sheet or cut length.

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

194

Tolerances On Out - Of - Squareness

q: Edge camber

u: Out-of-squareness

Notes1- The out-of-squareness “ u “ is the orthogonal projection of a transverse edge over a longitudinal edge.2- The out-of-squareness shall not exceed 1% of the actual width of the sheet.

Flatness Tolerance Thickness (mm)

Width (mm) Group A Group B<0.7 0.7≤t<1.2 ≥1.2 <0.7 0.7≤t<1.2 ≥1.2

600-1199 12 10 8 15 13 101200-1499 15 12 10 18 15 131500 and wide 19 17 15 22 20 19

A) The tolerances above in the table shall be applied for hot-dip metal coated flat products made from: Low carbon steels for cold forming (311, 312, 323, 324, 410, 411, 430, 431, 1311, 1312, 1313, 1314, 1315, 1411, 1412, 1413, 1414, 1415)Structural steels with a minimum yield strength (Re) < 280 N/mm2 (355, 1322, 1325, 1422, 1425),Bake-hardening steels with a minimum yield strength (Re) < 280 N/mm2 (482, 1118, 1122, 1124, 1218, 1222),Rephosphorised steels with a minimum yield strength (Re) < 280 N/mm2 (1522),

B) The tolerances above in the table shall be applied for hot-dip metal coated flat products made from structual steels (366, 367, 372, 1328, 1332, 1335, 1428, 1432, 1435), hot-dip metal coated flat products made from bake-hardening steels (1126, 1130, 1226, 1230) and hot-dip metal coated flat products made from dualphase steels (1660) with a minimum yield strength (Re) ≥ 280 N/mm2, except for products provided with zinc coating of 450 gr/m2 .

Notes1- Deviation from flatness shall be determined by measuring the deviation in distance between the product and a flat horizontal surface on

which the sheet is placed.

DIN EN 10143 - 1993


To

lera

nce

sG

alva

niz

ed/G

alva

nn

eale

d P

rod

uct

s


Notes1- Edge camber “q” is the maximum distance between a longitudinal edge and a straight edge supported on the latter.2- Edge camber shall be measured on the concave edge of the product.3- The basis of measurement shall be a distance of 2 m taken at any point on the edge.

Tolerances For Edge CamberDimension of Product

Type of Product Width (mm) Length (mm) Gauge Length (mm) Tolerance (mm)

Sheet≥ 600 ≥ 2000 2000 6≥ 600 < 2000 Actual length (L) + 0.003 x L

Coil ≥ 600 - 2000 6Slitted Coil < 600 - 2000 2

Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

196

GZR Zinc coated, galvanized coilGFR Zinc-iron alloy coated, galvannealed coilGZRK Zinc coated, galvanized coil with trimmed edgeGFRK Zinc-iron alloy coated, galvannealed coil with trimmed edge

Galvanized/Galvannealed Coil Products

Overseas Shipment

Packaging

• PE waterproof paper.• 2 inside edge protection rings.• 2 outside edge protection rings.• 2 circumferential straps.• 4 radial staps.

• PE waterproof paper.• 2 inside edge protection rings.• 2 outside edge protection rings.• 2 side protection disks.• Inside protection cover (galvanized sheet).• Outside protection cover (galvanized sheet).• 3 circumferential straps.• 4 radial staps.


Galvanized/Galvannealed Sheet Products

Pac

kag

ing


Gal

van

ized

/Gal

van

nea

led

Pro

du

cts

GZRS Zinc coated sheet cut from galvanized coilGFRS Zinc-iron alloy coated sheet cut from galvannealed coil

Overseas Shipment

GZRD Zinc coated, galvanized, slitted coilGFRD Zinc-iron alloy coated, galvannealed, slitted coil

Galvanized/Galvannealed Slitted Coil Products

• Wooden pallet. • PE waterproof paper and strapping.

• Wooden pallet. • PE waterproof paper. • Galvanized metal cover and strapping.

• Every single band with 2 circumferential strapsand 3 radial straps.

• Cartoon placed between bands.• Wrapping of bands with PE waterproof paper.• Final strapping of bands with wooden pallet.

198



Electrolytic Tinplateand ElectrolyticChromium CoatedSteel (ECCS or TFS)

202 > Grade Index 204 > Steel Grades209 > Available Sizes213 > Tolerances219 > Packaging

Tin

pla

te &

TF

S

200

Tin

pla

te &

TF

S

03201


www.erdemir.com.tr

Electrolytic Tinplate and Electrolytic Chromium Coated Steel (ECCS or TFS)

Electrolytic Tinplate is a cold-rolled low carbon mild steel sheet or coilmanufactured in 0.16-0.60 mm thicknessrange and coated on both surfaces withtin in various coating weights that isapplied in continuous electrolyticoperation.

Tin Free Steel or Electrolytic ChromiumCoated Steel (TFS or ECCS) is cold-rolledlow carbon mild steel sheet or coilmanufactured in 0.16-0.60 mm thicknessrange and coated on both surfaces withchromium/chromium oxide in variouscoating weights that is applied incontinuous electrolytic operation.

Tinplate and Tin Free Steel are mainlyused in packaging industry tomanufacture industrial cans, 2-piece and 3-piece food cans, beverage cans,aerosols, twist-off caps and crown caps,easy-open lids, decorative packagingand non-packaging products such aselectrical equipment and toys.

They have a combination of advantagesunrivalled in any other material;• Non-toxic• Light• Strong• Easily fabricated into intricate shapes• Weldability• Corrosion resistant


• Attractive appearance• Easily decorated by lithography• Recyclability

Tinplate and Tin free steels are producedafter the following production steps;• Pickling: The steel is pickled toeliminate the iron oxide that forms on thestrip during hot rolling process.•Tandem Rolling: Strip is cold rolled toreduce its thickness. On this process thethickness of strip reduced withoutmodifying the width.• Cleaning: After cold rolling, the steel is covered with a thin film of oil that isremoved by alkaline cleaning operation inorder to optimize the annealing process.• Annealing: The steel is heated in areducing atmosphere to above therecrystallizaiton point then cooled. Thereare two types of annealing techniques;batch annealing (BA) and continuousannealing (CA).• Tempering: The strip is tempered toachieve the required level of hardness,the required surface condition, shape,formability, good evenness and therequired mechanical properties. Alsosecondary rolling that is required for theproduction of DR tinplate can be done insuitable temper line.• Coating: In this operation the blackplateis passed continuously through theoperations of cleaning, electrolytic

pickling, electro-deposition of tin orchromium, induction-melting for tinplate,passivation and oiling. The final productis tinplate or tin free steel.

Erdemir's tinplate is produced in two maintypes; Single Reduced (SR) and DoubleReduced (DR) Erdemir's tin free steel isproduced mainly single reduced.

Single Reduced (SR): Steel stripreduced to desired thickness in one stepby cold rolling in the cold mill andsubsequently annealed and then coated.

General application fields: (Dependingon steel quality & annealing type) Industrialcan body and bases, 2 ve 3 pieces canbody and bases, beverage cans, easy-open lids, twist-off caps and crown caps,aerosols body, bases and tops.

Double Reduced (DR): Steel strip hasreceived a further cold rolling in whichbetween 10-30 percent reduction is givenafter annealing. Thus the steel reaches itsfinal thickness on two separate coldrolling.

General application fields: (Dependingon steel quality & annealing type)2 ve 3 pieces can body and bases,industrial can ends, easy-open lids,twist-off caps, and aerosol bodies.

Electrolytic Tinplate is a cold-rolled low carbon mild steel sheet orcoil manufactured in 0.16-0.60 mm thickness range and coatedon both surfaces with tin in various coating weights that is applied incontinuous electrolytic operation.

Tin

pla

te &

TF

S

202

Grade Index

Application Areas and Brand Correspondence of Tinplate and TFS Products


And Major ApplicationsErdemir

Steel Grade Standard Grade

2004 DIN EN 10202-01 TS245Electrolytic tinplate, single cold reduced, batch annealed 2005 DIN EN 10202-01 TS275(Food cans, beer cans, packaging material) 2006 DIN EN 10202-01 TS415

2023 DIN EN 10202-01 TS2302026 DIN EN 10202-01 TS2602104 DIN EN 10202-01 TS245

Electrolytic chromium coated steel (TFS) 2105 DIN EN 10202-01 TS275single cold reduced, batch annealed 2106 DIN EN 10202-01 TS415

2123 DIN EN 10202-01 TS230(Cans, crown caps, battery shells)2126 DIN EN 10202-01 TS2602223 DIN EN 10202-01 TH2302225 DIN EN 10202-01 TH245

Electrolytic tinplate, single cold reduced, continuously 2226 DIN EN 10202-01 TH260annealed (Food cans, beer cans, packaging material) 2228 DIN EN 10202-01 TH275

2242 DIN EN 10202-01 TH4152244 DIN EN 10202-01 TH4352252 DIN EN 10202-01 TH520

Electrolytic tinplate, double cold reduced continuously 2255 DIN EN 10202-01 TH550annealed (Cans, crown caps, battery shells) 2258 DIN EN 10202-01 TH580

2262 DIN EN 10202-01 TH6202323 DIN EN 10202-01 TH2302325 DIN EN 10202-01 TH245

Electrolytic chromium coated steel (TFS) single cold 2326 DIN EN 10202-01 TH260

reduced continuously annealed (Cans, crown caps,2328 DIN EN 10202-01 TH275

battery shells)2342 DIN EN 10202-01 TH4152344 DIN EN 10202-01 TH435


Tin

pla

te &

TF

S

05

Gra

de

Ind

ex

203


www.erdemir.com.tr


Page Material Number Previous EN USA JIS Number

1.0372 DIN EN 10203 T2 DIN EN 10202-01 TS 245 ASTM A 623 98 T53 JIS G 3303 87 2041.0375 DIN EN 10203 T3 DIN EN 10202-01 TS 275 ASTM A 623 98 T57 JIS G 3303 87 2041.0377 DIN EN 10203 T4 DIN EN 10202-01 TS 415 ASTM A 623 98 T61 JIS G 3303 87 2041.0371 DIN EN 10203 T1 DIN EN 10202-01 TS 230 ASTM A 623 98 T49 JIS G 3303 87 2041.0379 DIN EN 10203 T2,5 DIN EN 10202-01 TS 260 ASTM A 623 98 T55 JIS G 3303 87 2041.0372 DIN EN 10202 T2 DIN EN 10202-01 TS 245 ASTM A 623 98 T53 JIS G 3315 87 2051.0375 DIN EN 10202 T3 DIN EN 10202-01 TS 275 ASTM A 623 98 T57 JIS G 3315 87 2051.0377 DIN EN 10202 T4 DIN EN 10202-01 TS 415 ASTM A 623 98 T61 JIS G 3315 87 2051.0371 DIN EN 10202 T1 DIN EN 10202-01 TS 230 ASTM A 623 98 T49 JIS G 3315 87 2051.0379 DIN EN 10202 T2,5 DIN EN 10202-01 TS 260 ASTM A 623 98 55 JIS G 3315 87 2051.0371 DIN EN 10203 T1 DIN EN 10202-01 TH230 ASTM A 623 98 T49 JIS G 3303 87 2061.0372 DIN EN 10203 T2 DIN EN 10202-01 TH 245 ASTM A 623 98 T52 JIS G 3303 87 2061.0379 DIN EN 10203 T2,5 DIN EN 10202-01 TH 260 ASTM A 623 98 T55 JIS G 3303 87 2061.0375 DIN EN 10203 T3 DIN EN 10202-01 TH 275 ASTM A 623 98 T57 JIS G 3303 87 2061.0377 DIN EN 10203 T4 DIN EN 10202-01 TH 415 ASTM A 623 98 T61 JIS G 3303 87 2061.0378 DIN EN 10203 T5 DIN EN 10202-01 TH 435 ASTM A 623 98 T65 JIS G 3303 87 2061.0384 DIN 10203 DR 520 DIN EN 10202-01 TH520 ASTM A 623 98 DR 7,5 JIS G 3303 87 2081.0373 DIN 10203 DR 550 DIN EN 10202-01 TH 550 ASTM A 623 98 DR 8 JIS G 3303 87 2081.0382 DIN 10203 DR 580 DIN EN 10202-01 TH 580 ASTM A 623 98 DR 8,5 JIS G 3303 87 2081.0374 DIN 10203 DR 620 DIN EN 10202-01 TH 620 ASTM A 623 98 DR 9 JIS G 3303 87 2081.0371 DIN EN 10202 T1 DIN EN 10202-01 TH 230 ASTM A 623 98 T49 JIS G 3315 87 2071.0372 DIN EN 10202 T2 DIN EN 10202-01 TH 245 ASTM A 623 98 T52 JIS G 3315 87 2071.0379 DIN EN 10202 T2,5 DIN EN 10202-01 TH 260 ASTM A 623 98 T55 JIS G 3315 87 2071.0375 DIN EN 10202 T3 DIN EN 10202-01 TH 275 ASTM A 623 98 T57 JIS G 3315 87 2071.0377 DIN EN 10202 T4 DIN EN 10202-01 TH 415 ASTM A 623 98 T61 JIS G 3315 87 2071.0378 DIN EN 10202 T5 DIN EN 10202-01 TH435 ASTM A 623 98 T65 JIS G 3315 87 207

Tin

pla

te &

TF

S

204

Steel Grades

Electrolytic Tinplate (Single cold reduced, batch-annealed)Standard: DIN EN 10202 - 2001


Notes1- The above chemical limits are given for guidance only.

Mechanical Properties(1) (2)

Notes1- The values for tensile test apply to “Longitudinal” test pieces.2- All the values in the table are intended as a guide.

Erdemir Re, Rp0.2 Aim Values Rm Hardness Values (2)

Steel N/mm2 N/mm2 N/mm2 Previous (HR 30 Tm)

Grade Corresponding (kg/mm2) (kg/mm2) (kg/mm2) Standard d (mm)Standard Grade Re, Rp0.2 Rm Designationsd ≤ 0.210.21 < d ≤ 0.28d > 0.28

2023 DIN EN 10202 TS230180 - 280 230 325 275 - 375 T 50 T 1 53 max. 52 max. 51 max.

(18.4 - 28.6) (23.5) (33.2) (28.1 - 38.3)

2004 DIN EN 10202 TS245195 - 295 245 340 290 - 390 T 52 T 2 49 - 57 48 - 56 47 - 55

(19.9 - 30.1) (25.0) (34.7) (29.6 - 39.8)

2026 DIN EN 10202 TS260210 - 310 260 360 310 - 410 T 55 T 2.5 52 - 60 51 - 59 50 - 58

(21.4 - 31.6) (26.5) (36.7) (31.6 - 41.8)

2005 DIN EN 10202 TS275225 - 325 275 375 325 - 425 T 57 T 3 54 - 62 53 - 61 52 - 60

(23.0 - 33.2) (28.1) (38.3) (33.2 - 43.4)

2006 DIN EN 10202 TS415365 - 465 415 435 385 - 485 T 61 T 4 58 - 66 57 - 65 56 - 64

(37.2 - 47.4) (42.3) (44.4) (39.3 - 49.5)

ErdemirSteel Corresponding C Mn P S Si Al NGrade Standard Grade max. max. max. max.

2023 DIN EN 10202 TS230 0.03 - 0.06 0.20 - 0.35 0.020 0.020 0.025 0.020 - 0.070 0.0082004 DIN EN 10202 TS245 0.03 - 0.06 0.20 - 0.35 0.020 0.020 0.025 0.020 - 0.070 0.0082026 DIN EN 10202 TS260 0.04 - 0.08 0.20 - 0.35 0.020 0.020 0.025 0.020 - 0.070 0.0082005 DIN EN 10202 TS275 0.04 - 0.08 0.20 - 0.35 0.020 0.020 0.025 0.020 - 0.070 0.0082006 DIN EN 10202 TS415 0.09 - 0.12 0.30 - 0.50 0.020 0.020 0.025 0.020 - 0.070 0.008

Tin

pla

te &

TF

S

www.erdemir.com.tr

Ste

el G

rad

es

205


Electrolytic Chromium Coated Steel (TFS) (Single cold reduced, batch-annealed)Standard: DIN EN 10202 - 2001





Erdemir Re, Rp0.2 Aim Values Rm Hardness Values (2)


Grade Corresponding (kg/mm2) (kg/mm2) (kg/mm2) Standard d (mm)Standard Grade Re, Rp0.2 Rm Designations d ≤ 0.21 0.21 < d ≤ 0.28 d > 0.28

2123 DIN EN 10202 TS230180 - 280 230 325 275 - 375 T 50 T 1 53 max. 52 max. 51 max.

(18.4 - 28.6) (23.5) (33.2) (28.1 - 38.3)

2104 DIN EN 10202 TS245195 - 295 245 340 290 - 390 T 52 T 2 49 - 57 48 - 56 47 - 55

(19.9 - 30.1) (25.0) (34.7) (29.6 - 39.8)

2126 DIN EN 10202 TS260210 - 310 260 360 310 - 410 T 55 T 2.5 52 - 60 51 - 59 50 - 58

(21.4 - 31.6) (26.5) (36.7) (31.6 - 41.8)

2105 DIN EN 10202 TS275225 - 325 275 375 325 - 425 T 57 T 3 54 - 62 53 - 61 52 - 60

(23.0 - 33.2 (28.1) (38.3) (33.2 - 43.4)

2106 DIN EN 10202 TS415365 - 465 415 435 385 - 485 T 61 T 4 58 - 66 57 - 65 56 - 64

(37.2 - 47.4) (42.3) (44.4) (39.3 - 49.5)

ErdemirSteel Corresponding C Mn P S Si Al NGrade Standard Grade max. max. max. max.

2123 DIN EN 10202 TS230 0.03 - 0.06 0.20 - 0.35 0.020 0.020 0.025 0.020 - 0.070 0.0082104 DIN EN 10202 TS245 0.03 - 0.06 0.20 - 0.35 0.020 0.020 0.025 0.020 - 0.070 0.0082126 DIN EN 10202 TS260 0.04 - 0.08 0.20 - 0.35 0.020 0.020 0.025 0.020 - 0.070 0.0082105 DIN EN 10202 TS275 0.04 - 0.08 0.20 - 0.35 0.020 0.020 0.025 0.020 - 0.070 0.0082106 DIN EN 10202 TS415 0.09 - 0.12 0.30 - 0.50 0.020 0.020 0.025 0.020 - 0.070 0.008

Tin

pla

te &

TF

S

10 206

Electrolytic tinplate (Single cold reduced, continuously annealed)Standard: DIN EN 10202 - 2001





ErdemirSteel Corresponding C Mn P S Si Al NGrade Standard Grade max. max. max. max. max.

2223 DIN EN 10202 TH230 0.004 0.10 - 0.25 0.020 0.010 0.025 0.020 - 0.060 0.0052225 DIN EN 10202 TH245 0.004 0.10 - 0.25 0.020 0.010 0.025 0.020 - 0.060 0.0052226 DIN EN 10202 TH260 0.006 0.20 - 0.35 0.020 0.020 0.025 0.020 - 0.060 0.0062228 DIN EN 10202 TH275 0.02 - 0.05 0.10 - 0.25 0.020 0.020 0.030 0.030 - 0.080 0.0052242 DIN EN 10202 TH415 0.03 - 0.06 0.20 - 0.35 0.020 0.020 0.030 0.020 - 0.070 0.0092244 DIN EN 10202 TH435 0.03 - 0.06 0.20 - 0.35 0.020 0.020 0.030 0.020 - 0.070 0.015

Erdemir Re, Rp0.2 Aim Values Rm Hardness Values


Grade Corresponding (kg/mm2) (kg/mm2) (kg/mm2) Standard d (mm)Standard Grade Re, Rp0.2 Rm Designations d ≤ 0.21 0.21 < d ≤ 0.28 d > 0.28

2223 DIN EN 10202 TH230180 - 280 230 325 275 - 375 T 50 T 1 53 max. 52 max. 51 max.

(18.4 - 28.6) (23.5) (33.2) (28.1 - 38.3)

2225 DIN EN 10202 TH245195 - 295 245 340 290 - 390 T 52 T 2 49 - 57 48 - 56 47 - 55

(19.9 - 30.1) (25.0) (34.7) (29.6 - 39.8)

2226 DIN EN 10202 TH260210 - 310 260 360 310 - 410 T 55 T 2.5 52 - 60 51 - 59 50 - 58

(21.4 - 31.6) (26.5) (36.7) (31.6 - 41.8)

2228 DIN EN 10202 TH275225 - 325 275 375 325 - 425 T 57 T 3 54 - 62 53 - 61 52 - 60

(23.0 - 33.2 (28.1) (38.3) (33.2 - 43.4)

2242 DIN EN 10202 TH415365 - 465 415 435 385 - 485 T 61 T 4 58 - 66 57 - 65 56 - 64

(37.2 - 47.4) (42.3) (44.4) (39.3 - 49.5)

2244 DIN EN 10202 TH435385 - 485 435 460 410 - 510 T 65 T 5 61 - 69 61 - 69 60 - 68

(39.3 - 49.5) (44.4) (46.9) (41.8 - 52.0)

Tin

pla

te &

TF

S

11

Ste

el G

rad

es

207


www.erdemir.com.tr



Electrolytic Chromium Coated Steel (TFS) (Single cold reduced, continuously annealed)Standard: DIN EN 10202 - 2001



ErdemirSteel Corresponding C Mn P S Si Al NGrade Standard Grade max. max. max. max. max.

2323 DIN EN 10202 TH230 0.004 0.10 - 0.25 0.020 0.010 0.025 0.020 - 0.060 0.0052325 DIN EN 10202 TH245 0.004 0.10 - 0.25 0.020 0.010 0.025 0.020 - 0.060 0.0052326 DIN EN 10202 TH260 0.006 0.20 - 0.35 0.020 0.020 0.025 0.020 - 0.060 0.0062328 DIN EN 10202 TH275 0.02 - 0.05 0.10 - 0.25 0.020 0.020 0.030 0.030 - 0.080 0.0052342 DIN EN 10202 TH415 0.03 - 0.06 0.20 - 0.35 0.020 0.020 0.030 0.020 - 0.070 0.0152344 DIN EN 10202 TH435 0.04 - 0.08 0.25 - 0.45 0.020 0.020 0.030 0.020 - 0.070 0.015

Erdemir Re, Rp0.2 Aim Values Rm Hardness Values


Grade Corresponding (kg/mm2) (kg/mm2) (kg/mm2) Standard d (mm)Standard Grade Re, Rp0.2 Rm Des›gnat›ons d ≤ 0.21 0.21 < d ≤ 0.28 d > 0.28

2323 DIN EN 10202 TH230180 - 280 230 325 275 - 375 T 50 T 1 53 max. 52 max. 51 max.

(18.4 - 28.6) (23.5) (33.2) (28.1 - 38.3)

2325 DIN EN 10202 TH245195 - 295 245 340 290 - 390 T 52 T 2 49 - 57 48 - 56 47 - 55

(19.9 - 30.1) (25.0) (34.7) (29.6 - 39.8)

2326 DIN EN 10202 TH260210 - 310 260 360 310 - 410 T 55 T 2.5 52 - 60 51 - 59 50 - 58

(21.4 - 31.6) (26.5) (36.7) (31.6 - 41.8)

2328 DIN EN 10202 TH275225 - 325 275 375 325 - 425 T 57 T 3 54 - 62 53 - 61 52 - 60

(23.0 - 33.2) (28.1) (38.3) (33.2 - 43.4)

2342 DIN EN 10202 TH415365 - 465 415 435 385 - 485 T 61 T 4 58 - 66 57 - 65 56 - 64

(37.2 - 47.4) (42.3) (44.4) (39.3 - 49.5)

2344 DIN EN 10202 TH435385 - 485 435 460 410 - 510 T 65 T 5 61 - 69 61 - 69 60 - 68

(39.3 - 49.5) (44.4) (46.9) (41.8 - 52.0)

Tin

pla

te &

TF

S

208

Electrolytic Tinplate (Double cold reduced, continuously annealed)Standard: DIN EN 10202 - 2001

ErdemirSteel Corresponding C Mn P S Si Al N (ppm)Grade Standard Grade max. max. max. max. max. max.

2252 DIN EN 10202 TH520 0.06 0.30 0.020 0.020 0.030 0.025 - 0.065 802255 DIN EN 10202 TH550 0.06 0.30 0.020 0.020 0.030 0.025 - 0.065 902258 DIN EN 10202 TH580 0.06 0.35 0.020 0.020 0.030 0.025 - 0.065 1002262 DIN EN 10202 TH620 0.06 0.40 0.020 0.020 0.030 0.025 - 0.065 140





Erdemir Re, Rp0.2 Aim Values Rm Previous Hardness Values(2)

Steel N/mm2 N/mm2 N/mm2 Standard (HR 30 Tm)Grade Corresponding (kg/mm2) (kg/mm2) (kg/mm2) Designations

Standard Grade Re, Rp0.2 Rm DIN EN10203 ASTM A623 Min. Nominal Max.

2252 DIN EN 10202 TH520470 - 570 520 540 490 - 590 DR 520 DR 7.5 69 72 75

(48.0 - 58.2) (53.1) (55.1) (50.0 - 60.2)

2255 DIN EN 10202 TH550500 - 600 550 570 520 - 620 DR 550 DR 8 70 73 76

(51.0 - 61.2) (56.1) (58.2) (53.1 - 63.3)

2258 DIN EN 10202 TH580530 - 630 580 590 540 - 640 DR 580 DR 8.5 71 74 77

(54.1 - 64.3) (59.2) (60.2) (55.1 - 65.3)

2262 DIN EN 10202 TH620570 - 670 620 625 575 - 675 DR 620 DR 9 73 76 79

(58.2 - 68.4 (63.3) (63.8) (58.7 - 68.9)

Tin

pla

te &

TF

S


Ava

ilab

le S

izes


Electrolytic Tinplate and Electrolytic Chromium Coated Steel (TFS) Products

Available Sizes

General Thickness Range (mm)

Product Symbol Min. Max.

TNR 0.16 0.60 Single reduced electrolytic tinplate coil

TNRS 0.16 0.60 Single reduced electrolytic tinplate sheet cut from coil

DTNR 0.12 0.30 Double reduced electrolytic tinplate coil

DTNRS 0.12 0.30 Double reduced electrolytic tinplate sheet cut from coil

TFR 0.16 0.60 Single reduced chromium coated steel coil

TFRS 0.16 0.60 Single reduced chromium coated steel sheet cut from coil

Tin

pla

te &

TF

S

210

GradesGroup Code Product Type Annealing Type Steel GradeS1 DTNR Continuous 2252, 2255, 2258, 2262S2 DTNRS Continuous 2252, 2255, 2258, 2262Y1 (Coil) Batch (2)Y2 (Sheet) Batch (2)

Notes1- The minimum width is 650 mm.2- Requests for the production of the grades of groups Y1, Y2 are subject to negotiation.3- All of the products are produced to DIN EN 10202-2001.4- The temper designation is T72 for the grade 2252.

The temper designation is T73 for the grade 2255.The temper designation is T74 for the grade 2258.The temper designation is T76 for the grade 2262.

5- Length: min. 450 mm, max. 1168 mm.6- Coil weight: min. 3.000 kg, max. 20.500 kg.7- Maximum bundle weight: 2.700 kg.8- Inside diameter of coil is 420 mm.9- Surface finish with values of roughness is given in the table below:

DTNR Double reduced electrolytic tinplate coil

DTNRS Double reduced electrolytic tinplate sheet cut from coil


Thickness (mm) Group -S1 Group -S2 Group -Y1 Group -Y2

0.120 - 0.125 857 8570.130 - 0.145 907 9070.150 - 0.155 957 9570.160 - 0.300 1032 1016

Surface Type Surface Roughness Applied Products

(Ra, microns.)

Stone 0.35 ≤ Ra ≤ 0.60 DTNR, DTNRS

Fine Stone 0.25≤ Ra ≤ 0.45 DTNR, DTNRS

Tin

pla

te &

TF

S


Ava

ilab

le S

izes


Notes1- The minimum width is 650 mm2- The temper designation is T52 (T2) for the grades 2004, 2104, 2225, 2325.3- All of the products are produced to DIN EN 10202-2001 and TS EN 10202-2003.

The temper designation is T50 (T1) for the grades 2023, 2123, 2223, 2323.The temper designation is T55 (T2,5) for the grades 2026, 2126, 2226, 2326.The temper designation is T57 (T3) for the grades 2005, 2105, 2228, 2328.The temper designation is T61 (T4) for the grades 2006, 2106, 2242, 2342. The temper designation is T65 (T5) for the grades 2244, 2344.

4- The minimum thickness to be ordered for grades 2223, 2225, 2226, 2323, 2325, 2326 is 0.220 mm.5- The minimum thickness to be ordered for grades 2006, 2106 is 0.240 mm.6- The widths to be ordered for products TNRS, TFRS are between 650 mm and 1016 mm.7- Length: min. 450 mm, max. 1168 mm.8- Coil weight: min. 3.000 kg, max. 20.500 kg.9- Maximum bundle weight: 2.700 kg.10- Inside diameter of coil is 420 mm.11- Surface finishes with values of roughness are given in the table on page 212.

TNR Single reduced electrolytic tinplate coil

TFR Single reduced chromium coated steel coil

TNRS Single reduced electrolytic tinplate sheet cut from coil

TFRS Single reduced chromium coated steel sheet cut from coil

DimensionsMaximum Width (mm) (6)


Group-S1 Group-S2 Group-Y1 Group-Y20.160 - 0.175 857 857 857 8570.180 - 0.195 907 907 907 9070.200 - 0.215 957 957 957 9570.220 - 0.245 1032 1032 1032 10320.250 - 0.555 1050 1050 1050 10500.560 - 0.600 1050 1050

GradesGroup Code Product Type Annealing Type Steel GradeS1 TNR, TNRS Continuous 2223, 2225, 2226, 2228, 2242, 2244S2 TFR, TFRS Continuous 2323, 2325, 2326, 2328, 2342, 2344Y1 TNR, TNRS Batch 2004, 2005, 2006, 2023, 2026Y2 TFR, TFRS Batch 2104, 2105, 2106, 2123, 2126

Surface Type Surface Roughness Applied Products

(Ra, microns.)

Bright Ra ≤ 0.35 TNR, TFR, TNRS, TFRS

Fine Stone 0.25 ≤ Ra ≤ 0.45 TNR, TFR, TNRS, TFRS

Stone 0.35 ≤ Ra ≤ 0.60 TNR, TFR, TNRS, TFRS

Matt / Normal 0.60 < Ra ≤ 1.90 TNR, TNRS

Silver Ra ≥ 0.90 TNR, TFR, TNRS, TFRS

Tin

pla

te &

TF

S

212

Tin

pla

te &

TF

S


To

lera

nce

s


Tinmill products consist of single and double reduced low carbon mild steel electrolytically coated with either tin (tinplate) or chromium/chromium oxide (ECCS).

It should be noted that double cold reduced tinmill products are relatively less ductile than single cold reduced products and have very distinct directional properties, so for some uses, e.g. for three-piece can bodies, the direction of rolling should be stated.

Tolerances

Passivation

Under normal conditions of transport and storage, tinmill products shall be suitable for surface treatments such as established lacquering andprinting operations.

ECCS is not subject to a passivation treatment.

There are two tinplate passivation processes in common use:

a) Code 311: Values per surface for total chromium shall be 3.5 to 9.0 mg/m2

b) Code 300: Values per surface for total chromium shall be 1.0 to 3.0 mg/m2

Code 311 will normally be supplied unless otherwise specified.

DIN EN 10202 - 2001Symbols Of Products Covered By This Standard Tolerances: DTNR, DTNRS, TNR,TNRS, TFR, TFRS

Surface Type

Double reduced product is only supplied as stone finish.

Product Finish Tinplate / Eccs Nominal Surface Roughness(Ra, µm)

Bright Tinplate 0.35 and lessFine stone Tinplate / ECCS 0.25 - 0.45Stone Tinplate / ECCS 0.35 - 0.60Silver Tinplate > 0.90Matt Tinplate Various

Tin

pla

te &

TF

S

214

DIN EN 10202 - 2001

Coatings

The purity of tin used to produce the coating shall be not less than 99.85%.

Single Spot Values For Tin CoatingsNominal Coating Designations Single Spot Values (g/m2) (1)

g / m2 LB / BB min. max.2.0 0.18 1.60 3.002.8 0.25 2.30 3.904.0 0.36 3.35 5.305.0 0.45 4.20 6.505.6 0.50 4.70 7.208.4 0.75 7.15 -11.2 1.00 9.55 -

(1) The values for tin coatings per single surfaces shall be used for high speed welding applications (continuous electrical resistance welding at speeds greater than 30 m/min).

In order to distinguish between tinplate with differential coatings on the two surfaces and that with equal coatings, differentially coated tinplate shall be marked on one surface with straight parallel lines about 1 mm wide.

Marking shall be lines spaced at 75 mm intervals, indicating that the tinplate is differentially coated but does not identify the precise specification. The heavier coated surface shall normally be marked with continuous lines unless specified otherwise by the purchaser. Where marking is required on the lighter coated surface, interrupted lines shall be used.

ECCS MassesCoating Mass Each Surface (mg / m2) (1)

Form of Chromium min. max.Total chromium 50 140Chromium in oxide 7 35

(1) The values shall apply to the average of three single spot measurements.

Tin

pla

te &

TF

S


To

lera

nce

s


Thickness Tolerance

Thickness Tolerance Thickness Tolerance Thickness Tolerance(mm) (mm) (mm) (mm) (mm) (mm)0.13 ± 0.006 0.26 ± 0.013 0.39 ± 0.0190.14 ± 0.007 0.27 ± 0.013 0.40 ± 0.0200.15 ± 0.007 0.28 ± 0.014 0.41 ± 0.0200.16 ± 0.008 0.29 ± 0.014 0.42 ± 0.0210.17 ± 0.008 0.30 ± 0.015 0.43 ± 0.0210.18 ± 0.009 0.31 ± 0.015 0.44 ± 0.0220.19 ± 0.009 0.32 ± 0.016 0.45 ± 0.0220.20 ± 0.010 0.33 ± 0.016 0.46 ± 0.0230.21 ± 0.010 0.34 ± 0.017 0.47 ± 0.0230.22 ± 0.011 0.35 ± 0.017 0.48 ± 0.0240.23 ± 0.011 0.36 ± 0.018 0.49 ± 0.0240.24 ± 0.012 0.37 ± 0.0180.25 ± 0.012 0.38 ± 0.019

Notes1- Thickness shall be measured using a spring loaded micrometer accurate to 0.001 mm.2- Thickness at individual points shall not be measured within 6 mm of an edge.3- The thickness of the material shall conform to the following:

a) The deviation from the agreed thickness measured at the center line of the strip shall not exceed ± 5%b) The deviation from the agreed thickness measured at any point not within 6 mm of the mill trimmed edge shall be within + 5% to - 8%c) The average thickness shall not deviate from the nominal thickness by more than ± 2% for consignments comprising more than 10000 sheets (or meter equivalent when in coil form)

Feather Edge (Transverse Thickness Profile)

Feather edge is the thinning of material along the mill trimmed coil edge For both sheet and coil, the thickness when measured at a distance of 6mm from the mill trimmed edge shall not vary by more than 6% from the center thickness measured at right angles to the trimmed edge.

Tin

pla

te &

TF

S

216


Out-of-squareness (%) = Deviation (A) x 100Sheet dimension (B)

Notes1- The width and length is measured across the centre of the sheet laying on a flat surface, at right angles to the edges of the product.2- A rectangle of the ordered dimension shall be available from within each sheet.

Notes1- Out-of-squareness is the deviation of an edge from a straight line drawn at a right angle to the other side of the sheet, touching one corner

and extending to the opposite edge.2- For each sheet in the sample, the out-of-squareness shall not exceed 0.15%.

Width And Length ToleranceType Of Product Dimensions (mm) Tolerances (mm)

Lower UpperCoil Width 0 + 3

Sheet Width 0 + 3Length 0 + 3

DIN EN 10202 - 2001

Tin

pla

te &

TF

S


To

lera

nce

s


Short Pitch Camber Of Coils (Lateral Weave)

Edge Wave

The wave height (h) at any point shall not exceed 2.5 mm. No more than six waves in excess of 1.5 mm shall be present over a cut length of 1 m.

Bow

Bow is the residual curvature in sheet or coil such that the distance between the edges is less than the appropriate sheet or coil dimension. Bowmay be either convex or concave face uppermost on the bulk package. The normal convention is to express convex bow uppermost as a positive (+) value and concave bow as a negative (-) value.

The individual values of both longitudinal and transverse bow shall not exceed 30 mm. When purchased as coil, this shall apply after normal levelling operations.

Where both convex and concave bowed sheets are present in the same bulk package, the sum of the maximum values of each, ignoring the sign (+/-), shall not exceed 30 mm.

Centre Fullness

Centre fullness shall be determined by measurement of edge lift developed during the test. The value shall not exceed 9 mm.

Notes1- Short pitch camber is measured as the maximum deviation of the mill-trimmed edge from a straight line forming a chord to it over a relatively

short distance.2- Short pitch camber, measured over a chord length of 1 meter, shall not exceed 0.3 mm when measured prior to shearing.

W: Width of product

Tin

pla

te &

TF

S

218

Burr

Burr shall not be present such an extent as to interfere with the processing of the product.

Permissible Deviations From Inside And Outside Diameter Of Coil

Inside diameter of coil (420 mm): min. 405 mm, max. 430 mmOutside diameter of coil: min. 970 mm, max. 1580 mm

Welds Within A Coil

The number of welds in a coil shall not exceed three in lengths of 10000 m.The location of each weld in a coil shall be marked with a punched hole and additionally be indicated visibly.The total thickness of any weld shall not exceed 1.5 times the nominal thickness of the material forming the weld.In any lap weld, the total length of overlap shall not exceed 10 mm. The free overlap shall not exceed 5 mm.

DIN EN 10202 - 2001

Tin

pla

te &

TF

S


Pac

kag

ing


TNR Single reduced electrolytic tinplate coilDTNR Double reduced electrolytic tinplate coilTFR Single reduced chromium coated steel coil

Electrolytic Tinplate and Chromium Coated Steel (TFS) Coil Products

Overseas Shipment

Packaging

• PE waterproof paper. • 2 edge protection corrugated cardboard.• Circumferential cardboard. • Inside carboard paper.• Plastic transparent layer. • 2 cardboard side protection disks.• 1 side protection cover disk. (metal)• 2 outside protection rings.• Final paper covering.• Wooden pallet and strapping.

• PE Waterproof paper. • 2 edge protection corrugated cardboard.• Circumferential cardboard. • Inside carboard paper.• Plastic trasparent layer. • 2 cardboard side protection disks.• 2 side protection cover disks. (metal)• 2 outside protection rings.• Final paper covering.• Metal cover. (galvanized sheet)• Wooden pallet and strapping.


Tin

pla

te &

TF

S

220

Electrolytic Tinplate or Chromium Coated Steel (TFS) Sheets

TNRS Single reduced electrolytic tinplate sheet cut from coilDTNRS Double reduced electrolytic tinplate sheet cut from coilTFRS Single reduced chromium coated steel sheet cut from coil

Overseas Shipment

• Cardboard for bottom and top sides.• PE coated kraft paper.• Cardboard covering.• Edge protection with galvanized steel. • Wooden pallet and strapping.

• Top and bottom sides grey cardboard• PE coated paper.• Edge protection L shape galvanized steel. • Products are packed with cardboard and

metal cover on wooden pallet with strapping.



PRODUCT CODELAST DIGIT OF

PRODUCTION YEARLABEL NUMBER

Labelling

Lab

ellin

gL

abel

ling

By

- P

rod

uct

s

222

ASTMStandards

Benzene(D-836-80)

Toluene(D-362-80)

MotorBenzene

Xylene(D-364-77)

Solvent(D-3734-78)

TYPE-I

D-3505-78Specific Gravity

(15.5 °C)0.875-0.886 0.864-0.874 0.870-0.886 0.855-0.875 0.864-0.884

D-1209-79Color

SayboldNot Darker Than + 20





D-850-79Distilation

Range (°C)79.1-81.1 109.6-111.6 80-135 130-155 149-179

D-848-81Acid Wash

Color

Not Darker ThanNo: 3




—

D-847-79Acidity

— — — — —

D-853-79"S" Compounds

H2S or S02

— — — — —

D-849-79Copper Corrosion

TestNon-Corrosive Non-Corrosive Non-Corrosive Non-Corrosive

No Green or BlackDeposit

Special Specification For Erdemir Pig Iron (Basic Pig Iron)

Erdemir Quality No. Chemical Composition (%)Si Mn P S

Erdemir-Ç 3 1.00 max. 1.40 max. 0.15 max. 0.051-0.120

Erdemir-Ç 4 1.00 max. 1.40 max. 0.15 max. 0.050 max.

Erdemir-Ç 5 1.00-2.00 0.50-1.30 0.15 max. 0.060 max.

Erdemir has no regular pig iron production for sale. However, pig iron produced may be sold on request.

By - Products


By-

Pro

du

cts


By

Pro

du

cts

Iron Oxide (Typical)

Chemical Composition Distribution of Grain Size

Fe (in form of Fe2O3 ) 69.0% > 1.00 mm 18.7%

Zn 0.017% 0.75 – 1.00 mm 15.4%

Cl 0.02% 0.60 – 0.74 mm 13.8%

SiO2 0.003% 0.30 – 0.59 mm 50.9%

Density 5.7 g/cm3 < 0.30 mm 1.20%

Bulk density 3.1 g/cm3

Ammonium Sulphate

Appearance Crystal (white in color)

Chemical composition (NH4)2 SO4Moisture 0.5% max. (Wt %)

Free acid 0.06% max. (Wt %)

Screen analysis 50% (+20 mesh), 50% (- 20 mesh)

Total nitrogen 20.9% min.

Consignment Bulk

Appropriate to TS 856

By-

Pro

du

cts

224

Coke Breeze

Fixed Carbon 75% min.

Ash 18% max.

Volatile matter 3% max.

Sulphur 0.7% max.

Lower calorific value 6500 cal/g min.

Coarse size 20 mm undersize (distribution is variable)

Moisture Variable (determined in sale condition)

Crude Coal Tar

Water 4.0% max. Phenol (dry tar) 1%

0 – 180 °C 1% Naphtalene (dry tar) 12%

180 – 230 °C 12% Insoluble matter in Toluen 6%

230 – 270 °C 12% Insoluble matter in Quinoline 1-3%

270 – 360 °C 24% Freezing point (°C) (– 4) (+5)

Pitch 60% Ignition point (°C) 105-134

Bitumen 91% min. Density (g/cm3 at 20 °C ) 1.16-1.20

Sulphur 0.6% Viscosity (80 °C) E29-10.7

Ash (Wt %) 0.25% max.

Granulated Slag of Blast Furnace (Typical)

Chemical Composition Distribution of Grain Size

CaO 35-40% + 6.35 mm 2.5% max.

MgO 5-10% – 6.35, + 3.15 mm 2.5-7.5%

SiO2 33-38% – 3.15, + 1.60 mm 20-40%

Al2O3 13-19% – 1.60, + 1.00 mm 20-30%

S 1.5% max. – 1.00, + 0.40 mm 5-15%

MnO 2.5% max. – 0.40, + 0.15 mm 5-15%

FeO 1.0% max. – 0.15 mm 5% max.

K2O 2.0% max. Moisture 20% max.

TiO2 1.5% max. Bulk density 0.8-1.2 t/m3


By-

Pro

du

cts


Ho

t R

olle

d P

rod

uct

s

Production Flow Chart

226

Ho

t R

olle

d P

rod

uct

s



Co

ld R

olle

d P

rod

uct

s

Production Flow Chart

228


Co

ld R

olle

d P

rod

uct

s


Ad

dit

ion

al In

form

atio

n

230

Foreign Standards

National Standards and Related Bodies Country

ABS American Bureau of Shipping U.S.A.

AFNOR Association Française de Normalisation FRANCE

AISI American Iron and Steel Institute U.S.A.

ANSI American National Standards Institute U.S.A.

API American Petroleum Institute U.S.A.

ASME American Society of Mechanical Engineers U.S.A.

ASMI American Society for Materials International U.S.A.

ASTM American Society for Testing and Materials U.S.A.

BS British Standard U.K

BSI British Standards Institution U.K

CSA Canadian Standards Association CANADA

DIN Deutsches Institut für Normung GERMANY

DS Dansk Standard DENMARK

ELOT Hellenic Organization for Standardization GREECE

EN European Standard EUROPE

EU EURONORM EUROPE

FSA Finnish Standards Association FINLAND

GOST USSR State Standard RUSSIA

IBN Institut Belge de Normalisation BELGIUM

ISO International Organization for Standardization INTERNATIONAL

JIS Japanese Industrial Standard JAPAN

JSA Japanese Standards Association JAPAN

LRS Lloyd’s Register of Shipping U.K

MIL US Military Standards U.S.A.

NF Norme Française FRANCE

NNI Netherlands Normalisatie Instituut NETHERLANDS

NSF Norges Standardiseringsforbund NORWAY

ON Austrian Standards Institute AUSTRIA

SAE Society of Automotive Engineers U.S.A.

SNV Swiss Association for Standardization SWITZERLAND

TSE Türk Standardlar› Enstitüsü TURKEY

UNI Ente Nazionale Italiano di Unificazione ITALY

Additional Information

Ad

dit

ion

al In

form

atio

n



Conversion TableUnits to Convert Unit EquivalentsMass1 ounce (oz) = 28,349523125 g 0,06250 lb 141,747615625 carat1 pound (lb) = 453,59237 g 16 oz 0,00045359237 MT1 kilogram (kg) = 2,204622622 lb 35,27396195 oz 0,0685217659 slug1 metric ton (MT) = 1000 kg 2204,622621849 lb 1,102311311 ST1 short ton (ST) = 907,18474 kg 2000 lb 0,892857143 LT1 long ton (LT) = 1016,0469088 kg 1,12 ST 2240 lbLength1 inch (in) = 25,4 mm 0.0833333333 ft 25400 micron1 mikroinch (min) = 0,0254 micron 0,0000254 mm 25,4 millimicron1 foot (ft) = 30,48 cm 12 in 0,3333333333 yard1 millimeter (mm) = 0.0393700787 in 0,0032808399 ft 1000 micron1 micron (m) = 0,001 mm 10000 angstrom 0,0000393700787 in1 meter (m) = 39,37007874 in 3,280839895 ft 1,093613298 yard1 yard (yd) = 91,44 cm 36 in 3 ftArea1 in2 = 6,4516 cm2 645,16 mm2 0,00694444 ft2

1 cm2 = 100 mm2 0,15500031 in2 0,00107639 ft2

1 mm2 = 0,01 cm2 0,00155 in2 0,0000107639 ft2

1 ft2 = 92903,04 mm2 0,09290304 m2 144 in2

Volume-Density 1 in3 = 16,387064 cm3 16387,064 mm3 0,016387064 dm3

1 cm3 = 0,001 dm3 0,000001 m3 0,00003531467 ft3

1 US gallon (gal) = 3,785411784 dm3 231 in3 0,133680556 ft3

1 barrel (bbl) = 158,987294928 dm3 9702 in3 5,614583333 ft3

1 kg/dm3 = 1 g/cm3 1000 kg/m3 0,001 kg/cm3

1 g/cm3 = 0,001 kg/cm3 0,03613 lbm/ in3 62,42197 lbm/ft3

Force1 kilogram - force (kgf) = 9,80665 N 2,204622622 lbf 980665 dyne1 Newton (N) = 0,101971621 kgf 0,224808943 lbf 100000 dyneStress - Pressur 1 kgf/mm2 = 9,80665 N/mm2 1422,3343307 psi 980665 dyne/mm2

1 N/mm2 = 1 MPa 0,1019716213 kgf/mm2 9,869232667 atm1 lbf/in2 (psi) = 0.00070306958 kgf/mm2 0,00689475729 N/mm2 0,0680459639 atm1 atmosphere (atm) = 1,01325 bar 760 tor 760 mm Hg1 bar = 0,986923267 atm 0,1 N/mm2 14,503773773 psiEnergy1 kgf. m = 9,80665 J 2,343845602 cal 7,233013851 ft.lbf1 joule (J) = 0,101971621 kgf.m 0,737562149 ft.lbf 0,000947817120 Btu1 calorie (cal) = 4,1819 J 41819000 erg 0,426435123105 kgf.m1 Btu = 107,585755851 kgf.m 1055,055852620 J 778,169262266 ft.lbfTemperature°C (formula) = (°F – 32) / 1,8 K – 273,15 [ Rk x (5 / 9) ] – 273,15- 20 °C = - 4 °F 253,15 K 455,67 Rk- 10 °C = 14 °F 263,15 K 473,67 Rk

0 °C = 32 °F 273,15 K 491,67 Rk10 °C = 50 °F 283,15 K 509,67 Rk20 °C = 68 °F 293,15 K 527,67 Rk

Co

nta

ct In

form

atio

n

232

Contact Information

ERDEM‹R OFFICESWeb Site: www.erdemir.com.trOnline Sales: www.erdemironline.com

Ere¤li Iron And Steel Works Co.Office Address Phone Fax E-mailHead Office Eskiflehir devlet Yolu No: 12 0 312 292 66 40 0 312 287 44 39 [email protected]

06530 Sö¤ütözü / ANKARA

Plants Uzunkum No:7 0 372 323 25 00 0 372 316 39 69 [email protected] Kdz.Ere¤li 0 372 316 03 01

Sales DepartmentsOffice Address Phone Fax E-mailVice President, Uzunkum No: 7 0 372 329 46 62 0 372 322 09 48 [email protected]&Marketing 67330 Kdz. Ere¤li

Manager, Regional Uzunkum No: 7 0 372 329 48 78 0 372 312 54 86 [email protected]

Coordination of Sales 67330 Kdz. Ere¤li

Manager, Sales Uzunkum No: 7 0 372 329 46 63 0 372 312 43 46 [email protected]

Planning 67330 Kdz. Ere¤li

Manager, Foreign Sales Uzunkum No: 7 0 372 329 48 78 0 372 323 75 22 [email protected]

67330 Kdz. Ere¤li

Chief, Customer Technical Uzunkum No: 7 0 372 329 46 78 0 372 312 43 46 [email protected]

Services 67330 Kdz. Ere¤li

Regional Sales OfficesRegion Address Phone Fax E-mailAnkara Eskiflehir Devlet Yolu No: 12

0 312 292 66 40 0 312 287 15 89 [email protected] Sö¤ütözü / ANKARA

‹stanbul Atatürk Cad. S›tk› Bey Plaza 0 216 302 30 40 0 216 369 49 60 [email protected]: 82 Kat: 2 Daire: 10-11 0 216 369 79 00 0 216 385 91 7781090 Kozyata¤› / ‹STANBUL 0 216 385 90 26

‹zmir Cumhuriyet Bulvar› No: 139 0 232 463 62 92 0 232 422 10 71 [email protected]: 2 35210 ‹ZM‹R 0 232 463 62 96

Kdz. Ere¤li Uzunkum Cad. 30/A 0 372 329 45 77 0 372 316 29 54 [email protected] Kdz. Ere¤li 0 372 329 45 78

Documents

Katalog 2007 En