Kap 13 EN4416DE20EN - Papagayo System€¦ · · 2010-11-18ADD-BCSU:MTYPE=PER,LTG=1,LTU=1,SLOT=61,PARTNO="Q2316-X ",FCTID=3; – Configuring the HFA Standby board data ADD-HFAB:MTYPE=STMIHFA2,LTU=1,SLOT=61,SMODE=STBYRDY;

Solutions Siemens

Solutions

1 optiPoint 410 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Mobile HFA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 BPOOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Extended features for the Keysystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 Alternative Routing on Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 Edit Dial and Callog control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 UW7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299 HiPath Backup&Restore (HBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3110 CODEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

EN4416DE20EN© 2004 Siemens AG

1

2

SolutionsSiemens


Solutions Siemens

1 optiPoint 410

Install optiPoints 410 to a STMI2 board.

The connection between the optiPoints and the STMI2 should use voice compression.

Make a call and control, if a Codec with voice compression is used with the tools, you find on the PC.

Solution:

ADD-BCSU:MTYPE=PER,LTG=1,LTU=2,SLOT=43,PARTNO="Q2316-X ",FCTID=3;

ADD-HFAB:MTYPE=STMIHFA2,LTU=2,SLOT=43,SMODE=NORMAL,IPADDR=1.30.11.40, NETMASK=255.255.255.0,DEFRT=1.30.11.254;

RESTART-BSSU:ADDRTYPE=PEN,LTG=1,LTU=2,SLOT=43;

ADD-SBCSU:STNO=7188,OPT=OPTI,CONN=IP2,DVCFIG=OPTIIP,COS1=33,COS2=30, LCOSV1=9,LCOSV2=1,LCOSD1=9,LCOSD2=1,DPLN=0,ITR=0,STD=100;

ADD-SBCSU:STNO=7189,OPT=OPTI,CONN=IP2,DVCFIG=OPTIIP,COS1=33,COS2=30, LCOSV1=9,LCOSV2=1,LCOSD1=9,LCOSD2=1,DPLN=0,ITR=0,STD=100;

CHANGE-HFAB:MTYPE=STMIHFA2,LTU=2,SLOT=43,TYPE=ASC,CODECLST=G723;

● Set the Codec in the Configuration menu of the terminal:

– At the terminal: . Press the keys 1 0 3 simultaneously to get access to the “Configura-tion Menu” to change there the “Audio Settings”.

or

– Change the “Audio Settings” via the phone homepage with the following entry in the WEB Browser:

http://<ip address>:8082

● To see the used Codecs, start the homepage of the STMI2 board. To get access to the homepage of the STMI2 enter the following AMO command:

CHANGE-HFAB:MTYPE=STMIHFA2,LTU=2,SLOT=43,TYPE=DEBUG,FACCMODE=1;


3

4

ÜbungsaufgabenSiemens

a) When you are using the STMI2 homepage select the “dspSub” Menu -> “dspListActi-veChannels". All active calls are displayed. Note the B-channel. Return to the “dspSub” Menu enter the channel number under "show channel configuration". Now the channel configuration is displayed with the used Codec.

b) Also possible is to use the tool “Etherreal”, if a HUB is used or there are monitoring ports at the Layer 2 switch.


Solutions Siemens

2 Mobile HFA

1. Add the feature Mobile HFA in your system.

Solution:

a) Which central AMO parameters are necessary for the function ?

ADD-WABE:CD=*50,DAR=MHFALGON,CD2=#50;

CHANGE-FEASU:TYPE=A,CM=MOBHFA;

REGENARATE-PERSI:TYPE=COPIN; */ Checking if COPIN1 = Mobile

DISPLAY-PERSI:TYPE=SYS; */ Checkking the length of PIN1

b) Which settings for the subscribers are necessary ?

ADD-PERSI:TYPE=STN,STNO=7288,PIN1=7288;

ADD-PERSI:TYPE=STN,STNO=7289,PIN1=7289;

CHANGE-SDAT:STNO=7288,TYPE=ATTRIBUT,AATTR=MHFAHOME&MHFATBV;

CHANGE-SDAT:STNO=7289,TYPE=ATTRIBUT,AATTR=MHFAHOME&MHFATBV;

c) How is the handling on the terminal ?

– Handling at the terminal:

*50 7288# 7288#

or

Service Menu --> mobility LogOn "ok" ---> 7288# --> 7288#

2. Add the feature network wide.

Add a Secretary-Executive group on the otipoints 410. Use all special keys for the Secre-tary and for the Executive.


5

6

SolutionsSiemens

a) Is it possible to use the Secretary-Executive feature with Mobile HFA ?

b) Can the DSS (Direct Station Selection) be used ?

Solution:

CHANGE-SBCSU:STNO=7289,OPT=OPTI,SECR=Y;

ADD-CHESE:EXEC=7288,SECR=7189,ALLOC=E1S1;

CHANGE-TAPRO:STNO=7289,KY09=DSS,KY10=PUS,KY11=RNGXFER;

CHANGE-TAPRO:STNO=7288,KY09=DSS,KY10=RNGXFER;

ADD-ZIEL:TYPE=DSS,SRCNO=7289,KYNO=9,DESTNOD=7288;

ADD-ZIEL:TYPE=DSS,SRCNO=7288,KYNO=9,DESTNOD=7289;

3. Add the ATND-DAR for destination of a “to be visited” phone !

Solution:

ADD-ZIEL:TYPE=FWD,SRCNO=7289,SI=VCE,DESTNOF=92,NAME=HFA,DTYPE=CFNR,I TYPE=GEN,CFVAR=SYSTEM;

4. Activate and deactivate the feature with the HiPath 4000 Assistant !

Configuration Management --> System Data--> Maintenance --> Maintenance HFA mobile

Remark: All Executive and Secritary functions can be used when using the feature HFA Mobile.


Solutions Siemens


7

8

SolutionsSiemens


Solutions Siemens

3 BPOOL

1. Add a Standby board for the HFA board, already installed.

a) using the HiPath 4000 Assistant

● Add the Standby board:

– Start HiPath 4000 Assistant

– Select menu “Configuration Management”

– Change to “System Data” -> “Board” -> “Board”


9

10

SolutionsSiemens

– Configure the HFA Standby BOARD DATA.

– Add the board


Solutions Siemens

– Add the board pool:

– Select “Board Pool”

– Select “NEW”


11

12

SolutionsSiemens

b) Using AMO

– Existing board:


– Existing HFA generating:

ADD-HFAB:MTYPE=STMIHFA2,LTU=1,SLOT=91,SMODE=NORMAL,IPADDR=1.30.21.40, NETMASK=255.255.255.0,PATTERN=213,VLAN=NO,DEFRT=1.30.21.254,TCPP=4060, BITRATE="100MBFD",VLANID=0;

– Adding the Standby board:


– Configuring the HFA Standby board data

ADD-HFAB:MTYPE=STMIHFA2,LTU=1,SLOT=61,SMODE=STBYRDY;

– Adding the board pool:

ADD-BPOOL:MTYPE=STMIHFA2,POOLNO=1,LTU=1,SLOT=91,HOPAUT=SINGLE or MULTI;

ADD-BPOOL:MTYPE=STMIHFA2,POOLNO=1,LTU=1,SLOT=61,HOPAUT=SINGLE or MULTI;


Solutions Siemens

– Display the Board Pool:

DISPLAY-BPOOL;

H500: AMO BPOOL STARTED

+------------------------------------------------------------------------------+

| POOLNO = 1 MTYPE = STMIHFA2 HOPAUT = SINGLE |

| INFO = |

+------------------------------------------------------------------------------+

| LTU = 1 SLOT = 91 HOP-AUT-CNT = 0 HOP-MAN-CNT = 0 |

| DC-STATUS = READY LAN-CONN = READY SMODE = NORMAL |

+------------------------------------------------------------------------------+


| DC-STATUS = READY LAN-CONN = READY SMODE = STBYRDY |

+------------------------------------------------------------------------------+

2. Test the fuctionality by unplugging the LAN connection.

DISPLAY-BPOOL;


+------------------------------------------------------------------------------+


| INFO = |

+------------------------------------------------------------------------------+


| DC-STATUS = DEF LAN-CONN = SMODE = STBYDEF |

| SWITCHED AUTTO BRD LTU = 2 SLOT = 91 DATE/TIME : 2004-04-10 18:07 |

+------------------------------------------------------------------------------+



| SWITCHED AUTFR BRD LTU = 2 SLOT = 25 DATE/TIME : 2004-04-10 18:07 |

+------------------------------------------------------------------------------+


13

14

SolutionsSiemens

3. Set the “Standby defect” board to the state "Standby ready"


– Start the “Configuration Management”

– Select “Maintenance” -> “Board Maintenace”

– Search boards

– Change to “object list”

– Select board

– Change to “object”

– Select “Action” -> “Execute”

– Select “Restart board to standby ready mode”


Solutions Siemens

b) using AMO

RESTART-BSSU:ADDRTYPE=PEN,LTU=1,SLOT=91,HFASW=STBYRDY;

4. Switchover the subscribers to the Standby board manually.


– Search boards


– Select board



– Select “Switchover IP stations to Standby Ready board”


15

16

SolutionsSiemens

b) using AMO

RESTART-BSSU:ADDRTYPE=PEN,LTU=1,SLOT=61,HFASW=SWITCH,LTU2=1, SLOT2=91;

5. Delete the BPOOL History Data.


– Select the “Configuration Management”

– Select “System Data” -> “Maintenance” -> “Board Maintenance”

– Search boards


– Select board



Solutions Siemens


– Select “Reset board pool history”

Repeat this step for board SLOT=61;


17

18

SolutionsSiemens

b) using AMO

CHANGE-BPOOL:MTYPE=STMIHFA2,TYPE=HISTRES,LTU=1,SLOT=61;

CHANGE-BPOOL:MTYPE=STMIHFA2,TYPE=HISTRES,LTU=1,SLOT=91;;

DISPLAY-BPOOL;


+------------------------------------------------------------------------------+


| INFO = |

+------------------------------------------------------------------------------+


| DC-STATUS = READY LAN-CONN = READY SMODE = STBYRDY |

+------------------------------------------------------------------------------+



+------------------------------------------------------------------------------+


Solutions Siemens

4 Extended features for the Keysystem

1. Realize a Secretary-Executive group with a local Keysystem.

– For the needed keys use key modules at the phones.

Solution:

– Adding the Key functions for the Secretary and the Executice:

CHANGE-TAPRO:STNO=7189&4146,DIGTYP=OPTIA1,KY01=LINE,KY02=LINE;

ADD-KCSU:STNO=7146,TYPE=PRIM,PRIMKEY=20,RIOP=YES;

ADD-KCSU:STNO=7189,TYPE=PRIM,PRIMKEY=20,RIOP=YES;

ADD-KCSU:STNO=7146,TYPE=SEC,KYNO=21,STNOSEC=7189,RIOP=NO;

ADD-KCSU:STNO=7189,TYPE=SEC,KYNO=21,STNOSEC=7146,RIOP=NO;

a) The opposing call should be realized by the DSS feature.

Solution:

– Activate the feature „HOTLINE“:

CHANGE-FEASU:TYPE=A,CM=HOTRCL;

– Set authorization “HOT” in the needed COS class:

CHANGE-COSSU:TYPE=COS,COS=33,AVCE=HOT;

– Add two phantom subscribers:

ADD-SBCSU:STNO=7120&7121,OPT=OPTI,CONN=DIR,DVCFIG=OPTISET, COS1=333, COS2=30,LCOSV1=9,LCOSV2=1,LCOSD1=5,LCOSD2=1,STD=101, INS=SIGNOFF,TEXTSEL=ENGLISH;

– Change the key layout for the two subscriber:

CHANGE-TAPRO:STNO=7120&7121,DIGTYP=OPTIT12,KY05=LINE;


19

20

SolutionsSiemens

– Prepare both subscribers for the Keysystem:

ADD-KCSU:STNO=7120,TYPE=PRIM,PRIMKEY=5,RIOP=NO;ADD-KCSU:STNO=7121,TYPE=PRIM,PRIMKEY=5,RIOP=NO;

– Change the key layout for the Secretary and Executive:

CHANGE-TAPRO:STNO=7189&7146,DIGTYP=OPTIA1,KY03=LINE;

– Extend the existing Keysystem for the Secretary and Executive:

ADD-KCSU:STNO=7146,TYPE=SEC,KYNO=22,STNOSEC=7120,RIOP=YES, DSSLINE=YES;

ADD-KCSU:STNO=7189,TYPE=SEC,KYNO=22,STNOSEC=7121,RIOP=YES, DSSLINE=YES;

– Add Hotline destinations:

ADD-HOTLN:TYPE=HOTDEST,HTLNIDX=1,DEST=7120;ADD-HOTLN:TYPE=HOTDEST,HTLNIDX=2,DEST=7121;

– Add the HOTLINE INDEX to the subscribers:

CHANGE-SDAT:STNO=7121,TYPE=DATA1,HOTIDX=1;CHANGE-SDAT:STNO=7120,TYPE=DATA1,HOTIDX=2;

– Add the “Direct Station Selection for Line” (DSSLINE) to the subscribers:

CHANGE-SDAT:STNO=7120,TYPE=ATTRIBUT,AATTR=DSSLINE;CHANGE-SDAT:STNO=7121,TYPE=ATTRIBUT,AATTR=DSSLINE;

b) The Secretary should has access to the mailbox of the Executive.

Solution:

– Change the key layout for the Secretary:

CHANGE-TAPRO:STNO=7146,DIGTYP=OPTIA1,KY09=MB,KY10=MBLINE;


Solutions Siemens

– Assign the “Mailbox Line” to the Secretary:

ADD-ZIELN:STNO=7146,TYPE=MBLINE,KYNO=29,STNOMB=7189;

c) The Executive and the Secritary get a Ring Transfer key to switchover the accoustic signaling.

Solution:

– Change the key layout for the Secretary and Executive:

CHANGE-TAPRO:STNO=7189,DIGTYP=OPTIA1,KY06=RULEITNG;CHANGE-TAPRO:STNO=7146,DIGTYP=OPTIA1,KY14=RULEITNG;

– Activate the special authorization for the subscribers:

CHANGE-SDAT:STNO=7189,TYPE=ATTRIBUT,AATTR=RNGXFERL;CHANGE-SDAT:STNO=7146,TYPE=ATTRIBUT,AATTR=RNGXFERL;

– Add the “Ring Transfer” for both subscribers:

ADD-ZIELN:STNO=7189,TYPE=RNGXFERL,KYNO=25,STNORXFR=7146, RXFRFCT=SRC;

ADD-ZIELN:STNO=7146,TYPE=RNGXFERL,KYNO=33,STNORXFR=7189,RXFRFCT=DEST


21

22

SolutionsSiemens


Solutions Siemens

5 Alternative Routing on Error

1. Add an alternative route for any subscriber for the case OOS on error. An incoming call should be routed to a Public Network number (e.g. 0-30300-7xxx).

Solution:

CHANGE-SDAT:STNO=7480,TYPE=DATA1,STNOOOS=0303007341;

2. What happens, if the pen of the station is deactivated by AMO ?

Solution:

The caller gets the Busy Tone.

3. Realize that the incoming calls to this station is also routed to the alternative destination, if the station is deactivated by AMO.

Solution:

CHANGE-SDAT:STNO=7480,TYPE=DATEA1,AMOALTRT=YES;

4. All incoming calls to stations of a special Source Group sould be routet to the attendant in case of error.

Solution:

ADD-APRT:TYPE=ALTERR,SRCGRP=1,ALRTYPE=OOS,ALTRTNR=93,EXTNO=0;

– The following AMO command must be entered, if the alterative route should be used in this case too, if one of the subscribers of the source group is deactivated by AMO:

CHANGE-SDAT:STNO=7xxx&&7yyy,TYPE=DATA1,AMOALTRT=YES;


23

24

LösungenSiemens


Solutions Siemens

6 Call Forwarding

1. Realize the "old" call forwarding concept in the HiPath 4000 V2.0 !

Solution:

CHANGE-ZAND:TYPE=ALLDATA3,CFNRDEST=USECFUF;

a) Check the feature depending on AMO COSSU.

Solution:

Add CFNR and CFB in the used COS class and test the function. Both parameters should have the corresponding effect.

b) Are the menus in the Service Menu of the optisets/optiPoints changed?

Solution:

The menus of the Service Menu are not changed by setting the ZAND parameter.To change the Service Menu to the "old" structure, a Patch is needed!


25

26

ÜbungsaufgabenSiemens


Solutions Siemens

7 Edit Dial and Callog control

1. Realize the featurel "Edit Dial" in the system.

Solution:

CHANGE-ZANDE:TYPE=OPTISET,EDITDIAL=YES;

2. Testen Sie die Benutzeroberfläche:

Solution:

a) Number corretion before sending it.

Positioning the Cursor with the arrow keys (“<“ and “>”). Delete single digit with the Minus key (“-”).

b) Which keys are necessary for number corrections ?

Arrow keys (“<“ and “>”) and the Minus key (“-”).

c) For which types of terminals can this feature be used ?

Only for UP0E terminals.

d) What about terminals without a display ?

The parameters DIGNODIS and CALLOG in AMO SBCSU have to be set correctly for optiPoint 500 entry and optiset entry and basic (DIGNODIS=YES and CALLOG=NONE).

e) Change for test the parameter “DIGNODIS" to “NO” for an optiPoint 500 entry or opti-set entry / basic.

f) Test the calling situation for the entry/basic.

g) What happens after deactivation/activation of the entry/basic ?

The parameter DIGNODIS is set automatically to the right value. So the correct function is guaranteed.

3. The Callog entries should not can be deleted by the customer in the system.How do you can realize this feature ?

CHANGE-ZAND:TYPE=OPTISET,CALLOG=YES;


27

28

SolutionsSiemens


Solutions Siemens

8 UW7

1. How do you can block the startup of Unix UW7 ?

Solution:

DEACTIVATE-BCSM:UNIT=A1,SYSTEM=UNIX;

EXEC-UPDAT:UNIT=A1,SUSY=ALL;

UNIX startup is blocked for the next restarts/reloads until using the AMO command “ACTIVATE-BCSM:UNIT=A1,SYSTEM=UNIX;“ and “EXEC-UPDAT:......;“.

2. How do you can prevent Logbook entries, caused by UW7 ?

Solution:

CHANGE-FUNCT:LOGBKOFF="2"&"3"&"4";

2= exec-uplo/uplo2

3= regen CPTP

4= reg-funct


29

30

SolutionsSiemens


Solutions Siemens

9 HiPath Backup&Restore (HBR)

1. How is a “Recovery MOD” be created ?

Solution:

Hipath 4000 V2.0 Assistant -> Software Management -> Backup&Restore-> GLA/PDS

Select "HD -> MO"

2. Which RMX Areas of the HD are stored on the “Recovery MOD” ?

Solution:

Area E, F, G, H


31

32

SolutionsSiemens

3. Which Unix Data are stored on the “Recovery MOD” ?

Solution:

Install Partition of UW7 is stored on Area I of the MOD.

Additionally the Unix DB and RMX DB are store as packed files on the same Area (Area I).


Solutions Siemens

4. How do you can restore the Unix Data of the “Recovery MOD” ?

Solution:

In the Menu Restore -> Select MO-RMX / Type all /

with Option "Get original list from archive"

-> Select UNIX_CFDATA without RMX


33

34

SolutionsSiemens


Solutions Siemens

10 CODEW

1. How do you can find “marked resp. blocked” components in the HiPath 4000 V2.0systems ?

Solution:

DISPLAY-SDSU:STATUS=LICMARK,TYPE=PEN,LEVEL=PER3;

DISPLAY-SDSU:STATUS=LICBLOCK,TYPE=PEN,LEVEL=PER3;

2. There are 4 modes in the codeword, which could be activated in a HiPath 4000 V2.0 sys-tem (manually or automatically).

– Which modes are realized ?

Solution:

1. Normal Mode,

2. Trail mode,

3. Emergency mode,

4. Escalated Emergency mode


35

36

SolutionsSiemens


Documents

Kap 13 EN4416DE20EN - Papagayo System€¦ · · 2010-11-18ADD-BCSU:MTYPE=PER,LTG=1,LTU=1,SLOT=61,PARTNO="Q2316-X ",FCTID=3; – Configuring the HFA Standby board data ADD-HFAB:MTYPE=STMIHFA2,LTU=1,SLOT=61,SMODE=STBYRDY;