K35brouchure.rev2

(HANDAL]

K35

DECK

R84" TAIL SWING RADIUS

ACCESS LADDER

BOOM PIVOT

TOP OF PEDESTAL

42" X 42" CABIN

TANKS

12"

PEDESTAL 060" X 3/4" WT ASTM A36

NOMINAL BOOM LENGTH

CONFIGURATION ILLUSTRATED: 200 HP DIESEL ENGINE- REMOTE

"WALK-AROUND CONTROL

LUGS FOR JIB EXTENSION OPTION

24 3/8"

CL PIVOT

351/2"

K35brouchure.rev2

(RANDAL] TECHNICALSPECIFICATIONS CRANE-TYPE Pedestal mounted, precision slewing ring, ram luffing, box boom.

APPLICATION Designed for offshore applications. Constructed & rated to API 2C specifications.

NOMINAL REACH CAPACITY 35K lb. at 35 ft radius.

LOAD HOOK - MAXIMUM CAPACITY 60 short tons. MAXIMUM ROPE SIZE 1"

SHEAVE DIAMETER 20" MAXIMUM LINE FALL 8 WINCH MOUNTING On boom - eliminates two blocking by

luffing down; frees deck space.

AUXILIARY HOOK - MAX. CAPACITY 7 ½ short tons.

SWING - FINAL DRIVE External spur gear with low backlash and high precision.360 continuous rotation.

DRIVE High torque hydraulic motor, TRANSMISSION fully enclosed planetary gear reduction,

fail-safe multidisk wet static brake. 4:1 safety factor exceeds API 2C.

CAPACITY 75,200 ft-lb X 1 after accounting for friction in drive. Multiple drives recommended for floating applications.

SPEED@ FLOW 1 RPM@ 13.4 GPM X 1 swing circuit flow after accounting for motor slip.

MOTOR PRESSURE 2950 PSI Limit pressure. CONTROL Automatic hydraulic dynamic braking

with auto set static brake or free swing with manual set static brake.

SWING CIRCLE ASSEMBLY

BOLTING

PEDESTAL

BARREL

LIQUID CAPACITY

Sealed high precision anti-friction, 4 point contact single row ball bearing. High API 2C swing circle strength factor standard. Bearing balls mounted in-line with pedestal wall to minimize flange & raceway prying and maximize joint strength. Heavy duty bolting to sustain clamping under the highest crane loads - for maximum strength and life. Precision pre loading with no special tools required. 1 1/4" SAE J429 strength grade 8, impact toughness per API 2C, anti corrosion coating.

Precision machined flange. Flange meets □NV thickness requirements and API lamination quality requirements. Joined with full penetration butt welds. 60" OD,¾" Wall thickness, ASTM A36 material - minimum.

140 gallons fuel, 260 gallons hydraulic oil. For illustrated close radius 200 HP configuration with on-board diesel power & "open" control station.

MAXIMUM ROPE SIZE 1" SHEAVE DIAMETER 20"

MAXIMUM LINE FALLS 1 WINCH MOUNTING On boom - eliminates two blocking by

luffing down; frees deck space.

LUFFING - TYPE Hydraulic ram luffing. RAM Dual rams, double acting.

BORE 10" ROD Hard chrome plated rod.

SPEED@ FLOW 1 ½ minutes min. to max. angle @ 42.6 GPM. Limit flow 80 GPM.

PRESSURE Max working pressure 2400 PSI. Limit pressure 3000 PSI

MIN BOOM ANGLE O degrees to positive stop. MAX BOOM ANGLE 83 degrees to positive stop.

AUX. HOLDING Hydraulic lock valve directly mounted MECHANISM to cylinder.

CONTROL Power controlled lowering -automatic hydraulic dynamic braking with lock valve requiring power to lower load; no free fall or friction brake lowering.

BOOM CONSTRUCTION

ROPE REEVING

MARINE DUTY

QUALITY

Mild steel. HSLA or constructional alloy depending upon boom length. Longitudinal Internal stiffeners

@ bottom flange to preclude local buckling and ensure proper strength factors. Internal vertical web stiffeners to resist web buckling. Tapered construction provides for maximum strength / minimum weight. Fully seal welded.

Nylon sheaves with sealed anti friction bearings. Retainers prevent rope from leaving sheave groove. Rope guides with polymer rub strips provided as needed on boom. Fleet angle limited to 1½ degrees for optimum spooling. Minimum 18:1 pitch ratio. No reverse bending of ropes for maximum life. Heavy hook weight to prevent rope fouling at winch and at sheave.

Seal welding to suit harsh offshore environment, 3 coat marine paint system. Drive components and brakes are sealed and running in oil. Centralized anti-pollution spill containment provided below decking & machinery.

Official API 2C Monogram. API 01& ISO 9001 quality standards. Material fully traced. Welding to AWS D1.1. Thorough NOE and testing.

[ RANDAL J K35

MAXIMUM STATIC LOAD RATINGS(Lb)API Spec2C

RADIUS SOFT BOFT 70FT BOFT (Ft) BOOM BOOM BOOM BOOM

Minimum 122,000 122,000 122,000 122,000 10 113,500 122,000 122,000 15 93,700 102,900 100,200 97,000

20 77,800 79,500 78,400 75,200 25 62,800 62,600 62,400 61,700 30 51,700 51,500 51,400 51,000 35 43,900 43,700 43,600 43,100 40 38,100 37,900 37,800 37,000 45 33,700 33,400 33,300 32,200 50 28,600 29,900 29,700 28,400 55 27,000 26,800 25,300 60 22,000 24,200 22,600 65 22,000 20,400 70 17,400 18,500 75 16,800 80 12,900

Max thrust 288,000 290,000 292,000 297,000 z Cl) (Lb) Qz @moment

1,772,000 2,460,000 2,467,000 2,724,000 I- 0 <( - (Lb-Ft)□ I-z c.., Max moment=> <( 3,223,000 3,272,000 3,293,000 3,292,000 0 LL.I (Lb-Ft) LL C:::

@thrust (Lb)

112,000 100,000 102,000 139,000

Pub.021118 ref: 8.011102.050 8.011102.060 8.011102.070 8.011102.080

APPROXIMATE SHIPPING DATA COMPONENT

WEIGHT VOLUME (LB) FTxFTxFT

PEDESTAL 720 + 475xL Lx 5.6 x 5.6 L = LENGTH IN FEET.

TURRET 9,000 7.8 X 5.9 X 5.7 WEIGHT INCLUDES MACHINERY.

R AMS (2) 4,200 2.4 X 11.1 X 1.5 FOR ILLUSTRATED CONFIGURATION.

BOOM-50 FT 10,700 3.2 X 7.2 X 54.5

BOOM-60 FT 13,000 3.2 X 7.2 X 64.5 Foundation reactions based on dead BOOM -70 FT 14,800 3.2 X 7.2 X 74.5 load plus live load x 1.5 x Cb.•

BOOM-BO FT 19,800 3.2 X 7.2 X 84.5 Ratings shown are per WINCH+ HOOK BLOCKS 7,300 6.5 X 4.0 X 6.0 API Spec 2C.7'h Ed.@ Cb.= 1.33, 0 wind

CONTROL DECK 2,200 6.8 X 4.1 X 4.9 speed, 0° offlead , 0° sidelead & level

AFT DECK 800 8.8 X 3.1 X 4.9 fixed foundation.

ENGINE DECK 4,000 10.0 X 4.6 X 7.0 Actual ratings are typically lower due

LADDER - ACCESS 100 8.0 X 2.0 X 0.8 to optional hoist system limitations or dynamic conditions.

FUEL & OIL 3,000 (B)DRUMS

ACCESSORIES VARIES VARIESDeduct the weight of the hook block to determine the lifting capacity.

K35brouchure.rev2