Kinder and Co. Pty. Ltd. Copyright © 2008 ABN 28 006 489 238

+61 (3) 9587 9244 +61 (3) 9587 9344 sales@kinder.com.au www.kinder.com.au

K-Tra iner Be l t Al ignment Id ler

K-Trainer is an all-purpose conveyor belt alignment

idler, that will direct the belt correctly under all

operating conditions.

The two inverted vee rollers, put pressure down onto the belt,

promoting centralised belt training. The universal frame adjusts to

all types of mounting structures and is suitable for reversing belts.

After installation, the unit requires no further attention.

As the return strand of the belt is critical to maintain correct

belt alignment the K-Trainer is ideally installed just after the head

pulley, or prior to the tail pulley.

By having the return strand of the belt running true, this will help

direct the carry side of the belt and therefore minimise material

spillage and belt damage.

•Limits Belt Damage

•Controls Spillage

•Easily Installed

•Suitable for reversing belts

•Universal Fit

•Available for all belt widths

Kinder and C

o. Pty. Ltd. Copyright ©

2008 ABN

28 006 489 238

+61 (3) 9587 9244 +

61 (3) 9587 9344 sales@kinder.com

.au ww

w.kinder.com

.au

K-T

rainer B

elt Align

men

t Idler

Specifications subject to change without notice.

Certified draw

ings are available on request.

Kinder and Co. Pty. Ltd. Copyright © 2008 ABN 28 006 489 238

+61 (3) 9587 9244 +61 (3) 9587 9344 sales@kinder.com.au www.kinder.com.au

Tru-Trac ® Conveyor Be l t Track ing System

Tru-Trac® Conveyor Belt Tracking System is an

innovative and versatile mechanism, which will

operate with all belt types and environments in both

wet and dry conditions. The range covers solutions

for trough (load carrying) and return types on slow

moving, reversible, high speed and high load belts.

The internal vertical pivot axis unique tracking action causes

the unit to “kick in” immediately the belt starts to drift off

center. It does not rely on belt edge contact.

The Tru-Trac® incorporates a rubber covered crown face

which causes the drum to pivot about the perpendicular axis

and this results in the tracking action always being on the

same horizontal plane as the belt.

•Suitable for wet and dry conditions

•Requires minimum force to activate

•Does not rely on belt edge contact

•Simple to install

•Maintenance free

•Adjustable mounting brackets

Kinder and Co. Pty. Ltd. Copyright © 2008 ABN 28 006 489 238

+61 (3) 9587 9244 +61 (3) 9587 9344 sales@kinder.com.au www.kinder.com.au

Tru-Trac ® Conveyor Be l t Track ing System

Trough Tracker

Specifically designed for the load carrying side. Wing rollers

are incorporated into the standard pivot system. Suitable

for all troughing angles 15 to 45 degree. The unit utilizes

the center roller to steer where the most effective steering

forces are exerted.

Flat Return Tracker

Works well with reversible and shuttle conveyors and suitable

for belt speeds up to 7 meters / second.

Dual Return Tracker

Designed to accommodate excessive forces encountered

with wide belts and heavy loads. Two separate tapered

rollers are mounted onto the pivot mechanism.

Guidelines for Installation

•Only required where misalignment occurs. As a general

rule one unit is sufficient to align 50 meters of belt. On

very long belts spacing may be increased upto 100 meters.

•One unit is needed to keep the beltrunning center through

the gravity take up.

•Works equally well with reversible and shuttle conveyors.