Upload
energicul
View
233
Download
0
Embed Size (px)
Citation preview
8/16/2019 Jvc Xr-d400sl Service En
1/28
SERVICE MANUAL
ContentsSafety precautions
Technical description
Disassembly method
Troubleshooting
Precaution for servicing
1-2
1-3
1-6
1-9
1-13
MULTIPLE COMPACT DISC RECORDER
PO
WER
1 TRACK ALLREPEAT
SPEED
ERASE
OVER
OPEN/CLOSESOURCE
SPEED
REPEAT FINALIZE
PROGRAM
REC
4x 2x 1x
1
11
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
OPEN/CLOSE
REC/PLAY
SCSI AUTO REC
XR-D400SL
XR-D400
E Germany
Area Suffix
8/16/2019 Jvc Xr-d400sl Service En
2/28
R-D400SL
2
Safety precautions
1. This design of this product contains special hardware and many circuits and components speciallyfor safety purposes. For continued protection, no changes should be made to the original design
unless authorized in writing by the manufacturer. Replacement parts must be identical to thoseused in the original circuits. Services should be performed by qualified personnel only.
2. Alterations of the design or circuitry of the product should not be made. Any design alterations ofthe product should not be made. Any design alterations or additions will void the manufacturer`s
warranty and will further relieve the manufacture of responsibility for personal injury or propertydamage resulting therefrom.
3. Many electrical and mechanical parts in the products have special safety-related characteristics.These characteristics are often not evident from visual inspection nor can the protection afforded
by them necessarily be obtained by using replacement components rated for higher voltage,wattage, etc. Replacement parts which have these special safety characteristics are identified inthe Parts List of Service Manual. Electrical components having such features are identified by
shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of asubstitute replacement which does not have the same safety characteristics as the recommended
replacement parts shown in the Parts List of Service Manual may create shock, fire, or otherhazards.
4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and thelike to be separated from live parts, high temperature parts, moving parts and/or sharp edges
for the prevention of electric shock and fire hazard. When service is required, the original leadrouting and dress should be observed, and it should be confirmed that they have been returned
to normal, after re-assembling.
5. Leakage current check (Electrical shock hazard testing)
After re-assembling the product, always perform an isolation check on the exposed metal partsof the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control
shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transformer during this check.
Plug the AC line cord directly into the AC outlet. Using a "Leakage Current Tester", measure
the leakage current from each exposed metal parts of the cabinet , particularly any exposed
metal part having a return path to the chassis, to a known good earth ground. Any leakagecurrent must not exceed 0.5mA AC (r.m.s.)
Alternate check methodPlug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohmsper volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by
a 0.15 F AC-type capacitor between an exposedmetal part and a known good earth ground.
Measure the AC voltage across the resistor with theAC voltmeter.
Move the resistor connection to each exposed metalpart, particularly any exposed metal part having areturn path to the chassis, and measure the AC
voltage across the resistor. Now reverse the plug in
the AC outlet and repeat each measurement voltagemeasured any must not exceed 0.75 V AC (r.m.s.).This corresponds to 0.5 mA AC (r.m.s.).
Good earth ground
Place thisprobe on
each exposedmetal part.
AC VOLTMETER(Having 1000ohms/volts,or more sensitivity)
1500 10W
0.15 F AC TYPE
! CAUTION Burrs formed during molding may be left over on some parts of the chassis. Therefore,pay attention to such burrs in the case of preforming repair of this system.
8/16/2019 Jvc Xr-d400sl Service En
3/28
8/16/2019 Jvc Xr-d400sl Service En
4/28
R-D400SL
4
The XR-D400 incorporates the SCMS (Serial Copy Management System) and the RID (Recorder Unique Identifier)
functions.SCMS is used to limit digital copies to one generation only. The principles are shown in Fig. 3.With RID, the RID codes are written into discs which are as specified in the Orange Book Parts II and III. The
codes contain the manufacturer's name, product name and machine number to enable the tracing of i llegal copies.
Digital recording Digital recording
[Fig. 3] Principles of SCMS
Fig. 4 shows the structure of a CD-R disc.
In recording, a laser beam having the same wavelength as theCD beam (780 nm) but of tens times higher power is irradiated
from the substrate surface to the groove.This irradiation causes thermal deformation of the organic
pigment layer forming pits in it.The organic pigments include cyanine, phtalocyanine and azoicdyes and the reflective layer uses gold or silver materials.
In playback the laser beam reads the pits recorded in thepregroove.
The thermal deformation of the organic pigment layer cannot berecovered to the original condition. As a result, the CD-R discs
cannot be rewritten and only additional writing is possible withthem.
Fig. 5 shows the structure of a CD-RW disc.The CD-RW uses a phase-changing recording material in the
recording layer.With the CD-RW, a laser beam with regulated power andcooling time is irradiated to form a crystalline phase (erased
status) and amorphous phase ( recorded s tate) on thepolygroove and data is reproduced according to the difference in
reflectivity of the two phases.An amorphous state can be obtained by quick cooling after
irradiation by a strong laser beam.The phase-changing recording material is made of a compoundof silver, indium, antimony and tellurium, and rewrit ing is
possible up to about 1000 times.
As the reflectivity at 780 nm of the CD-RW is lower than the CD-R, the RF amp gain should be changed in order to play a CD-RW disc.
SCMS and RID functions
Recording on CD-R discs
Recording on a CD-RW disc
Comparison between the CD-R and the CD-RW
Label printed surface
Protective layer groove
Reflective layer
Organic pigment layer
Substrate
pregrooveTrack pitch
1.6 µm
Laser beam
Signal surface
[Fig. 4]
Printed surface
Protective layer
Aluminum reflective layer
Upper protective layer
Recording layer
Lower protective layer
Substrate
polygroove
Signal surfaceLaser beam
[Fig. 5]
CD-RCompact Disc Recordable
CD-RWCompact Disc Rewritable
Specifications
Laser reflectivity
Recording power
Playback on CD player
Orange Book Part II
65% or more
4 to 11 mW
Possible
Orange Book Part III
15% to 25%
8 to 14 mW
Impossible
[Table 2]
8/16/2019 Jvc Xr-d400sl Service En
5/28
XR-D40
CD-R/RW
CD-R/RW
Lead-in areaThis area records the TOC (Table Of Contents) including the number of tracks in the disc, track-start position
information, etc.
DataThis area contains the recording of actual audio signals, file data, etc.The unit used in the data area is the track. Usually, music CDs use a track per song selection while the CD-
ROM discs basically uses only one track.
Lead-outThis area is used to indicate that the data in the disc has reached the end.
The combination of the lead-in, data and lead-out areas is referred to as a single session.A disc containing multiple sessions is called a multi-session disc. The CD-EXTRA belongs to this kind of disc.
PCA (Power Calibration Area)This area is used to regulate the laser power in data writing.
Its data optimizes laser power according to external factors such as the medium type, supply voltage andoperating temperature. The PCA provides an area for use in 99 times of test writing.
PMA (Program Memory Area)This area contains the recording of the start and end positions of the tracks. When a disc is not finalized in
program recording, this area is used to obtain the preliminary TOC data.
PMA Track 1
Track 1
Track 1
Track 2
Track 2 Lead-out
PMA
PMA Lead-in
Recording method of the CD-R/RW
As shown in Fig. 6, the recording areas of a CD-ROM and a CD-R/RW are different.These discs use two recording areas in addition to the areas used for data recording by ordinary CD discs.
Finalization
Finalization refers to writing the preliminary TOC data in the PMA into the lead-in and lead-out areas.When a disc is not finalized, its TOC data is recorded exclusively in the PMA.
Since ordinary CD players cannot read the PCA and PMA, non-finalized discs can be read only with aREC/PLAY machine such as the XR-D400. This makes possible addition writing on the disc.When a disc is finalized, its lead-in, data and lead-out areas are written properly and the disc becomes a disc
complying with the Orange Book specifications.Fig. 7 shows the finalization procedure.
2 areas for CD-ROM
Inner direction Outer direction
PCA PMA Lead-in Data Lead-out
[Fig. 6]
[Fig. 7]
Before finalization
Track rewriting
After finalization
(Preliminary TOC)
TOC data
8/16/2019 Jvc Xr-d400sl Service En
6/28
R-D400SL
6
1. Remove the 4 screws A from both sides of the top cover.
2. Remove the 4 screws B from the rear of the top cover, thenremove the stop cover.
Disassembly method
Removing the top cover (Figs. 1 & 2)
1. Remove the top cover.
2. Remove the 3 screws C that retain the front panel from thebottom. (Fig. 3)
3. Unplug the connector A from the power supply board (Fig. 4)
and the flat wire from the control board (Fig. 5).
4. Disengage the 2 claws D from the front panel and removethe front panel. (Figs. 4 and 5)
Removing the front panel (Figs. 3 to 5)
1. Remove the stop cover.
2. Unplug connector B from the power supply board (Fig. 4).
3. Remove the 6 screws E from the rear panel (Fig. 6).
4. Remove the 2 screws F retaining the SCSI connector, thenremove the rear panel.
(CAUTION) Screw F retaining the SCSI connector functions toprotect the connector. Be sure to remove it as alast task in disassembly or a first one in assembly.
Removing the rear panel (Figs. 4 & 6)
Front panel
Connector BConnector A
Flat wire
A
A
B
B
C
DD
G
G G
G
Fig. 1
Fig. 2
Fig. 3
Fig. 5Fig. 4
8/16/2019 Jvc Xr-d400sl Service En
7/28
XR-D40
F
E
E
CD-ROM drive
CD-R/RW drivePower supply
connectors
Control cable
Audio signal connector
H
H
Flat cable
Flat cable
Connector
I
I
1. Remove the top cover.
2. Remove the rear panel.
3. Unplug the connectors from the drives (CD-ROM drive:
power supply connector and control cable connector.CD-R/RW drive: power supply connector, control cable
connector and audio signal connector). (Fig. 7)4. Remove a total of 8 screws retaining the drives, from
the side panels. (Figs. 4 and 5)
5. Take out each drive in the rear direction.
Removing the CD-ROM and CD-R/RW drives(Figs. 4, 5 and 7)
1. Remove the top cover.2. Remove the rear panel.
3. Remove the CD-R/RW drive.
4. Remove the 6 screws H retaining the cover, then remove
the cover. (Figs. 8 and 9)
5. Stand up the board and unplug the 2 flat cables and 1connector. (Fig. 10)
6. Remove the 4 screws I retaining the circuit board. (Fig. 11)
7. Unplug 1 flat cable and remove the circuit board. (Fig. 12)
Removing the CD-R/RW drive board(Figs. 8 to 12)
Fig. 6
Fig. 7
Fig.8
Fig. 9
Fig. 12
Fig. 10
Fig. 11
8/16/2019 Jvc Xr-d400sl Service En
8/28
R-D400SL
8
JJ
CD-ROM drive
CD-R/RW drive
Tray eject hole
Tray eject hole
1. Remove the top cover.
2. Remove the front panel.
3. Remove the 13 screws J retaining the board.
Removing the front board (Fig. 13)
1. Remove the top cover.
2. Remove the front panel.
3. When removing a disc from the CD-ROM drive (upper
drive), insert a thin wire or similar object into the trayeject hole at the right end of the drive. When the drive
comes out, pull it out toward the front.
4. When removing a disc from the CD-R/RW drive (lowerdrive), insert a thin wire or similar object into the tray
eject hole at the left end of the drive. When the drivecomes out, pull it out toward the front.
Removing the disc (Fig. 14)Fig. 13
Fig. 14
8/16/2019 Jvc Xr-d400sl Service En
9/28
XR-D40
NO
YES
YES
NO
OK
NO
NO
NO
NO
YES
YES
YES
YES
YES
YES
YES
NO
NO
Troubleshooting (For repairing the audio CD dubbing)
POWER button ONCheck the CN991 and S1034
on the Front board.
Does the POWERindicator light?
Are the pins and of the CN991on the Front board short-circuited
Go to the "PowerSupply Operation".
Can the tray beopened/closed with theOPEN/CLOSE button?
Go to the"OPEN/CLOSE Operation".
Can the SOURCE disc
drive read theTOC of the CD?
Go to the
"Reproduction Operation"
Can the REC/PLAY discdrive play the CD?
Is the audio output fromthe CD in the REC/PLAY
disc drive?
Can the data be written
in the REC/PLAYdisc drive?
Are the front keys andindicators normal?
Check the general
operations.
Go to the"Audio Operation".
Go to the
"Write Operation".
Go to the "Front Key /Indicator Operation".
8/16/2019 Jvc Xr-d400sl Service En
10/28
R-D400SL
10
CN991 section
(Note) Connection points of the 4 wires.
Do not disconnect anyother connections.
YES YES
YES
YES
YES
NO
NO
NO
First remove the 4 wires connected to the Power Supply unit (QAL0244-002) (see photo below) to do a check
of the stand-alone mode.(1) Press the POWER button to ON, and check the voltages at the leftmost wire (red, DC +5 V) and the
rightmost wire (yellow, DC +12 V).Then connect the wires and check the voltages as described below.
(1) Check the continuity between the GND line and leftmost wire (red, DC +5 V) and the rightmost wire (yellow,+12 V) to ensure that there is no short-circuiting.
(2) Press the POWER button to ON and check the voltages at the leftmost wire (red, DC +5 V) and therightmost wire (yellow, DC +12 V).If the CD voltage drops abnormally or the protection device (fuse, etc.) is released when the wires are
connected (i.e. load is applied), there may be short-circuiting on the load side or in the connection path.
Power supply operation
OPEN/CLOSE operation
Press theOPEN/CLOSE button.
OPEN/CLOSEoperation is OK.
Is DC powersupply normal?
Does the trayopen or close?
Can other buttons
be used?
Can the tray beopened/closed by the
OPEN/CLOSE button in the
stand-alone mode.
Check connections ofCN602, CN603 and
drives.Check the Front and
Control boards.
Check connections ofCN111 and CN001.
Check the Front andControl boards.
Check the connections
of CN602, CN603 andthe drives.
Go to the"Power Supply Operation".
In the stand-alone mode theOPEN/CLOSE button can be
pressed by removing thefront panel.
CD-ROM
drive
CD-R/RWdrive
8/16/2019 Jvc Xr-d400sl Service En
11/28
XR-D40
Note 1) The access condition of each drive is shown by an indicator.
Blinking: The disc TOC data is being read.Lighting: The disc TOC data has been read or is being reproduced.
Note 2) The TOC data of the disc in the SOURCE disc tray (CD-ROM drive) can be displayed as follows.
When the SOURCE indicator stops blinking and starts constant lighting, press the skip button (rewinddirection) to display the number of tracks on the disc.
Examples) CTS-1000 Disc with 28 tracks: Track indicators 1 to 20 (Green) and the OVER indicator (Red) lights.Other Disc with 12 tracks: Track indicators 1 to 12 (Green) light.
Reproduction operation
Audio operation
Insert a disc.
Can the TOC be read?
Is playback possible? Applicable to REC/PLAY disc tray only.
Reproduction
operation is OK.
Check the connections of
the CN602, CN603 anddrives.
Check the drives.
Check buttons.Check the CD-R/RW drive.
YES
YES
YES
NO
NO NO
YES
NO
NO
During playback
Is audio output?
Audio operation is normal.
Is the audio freefrom noise orsound skip?
Is audio normalat CN401 on
Control board?
Check the surroundingsof J401 on the IC401.
Check the 3-pin wireconnections.
Replace HQA-030A. Replace HXL-3BSPA.
8/16/2019 Jvc Xr-d400sl Service En
12/28
R-D400SL
12
The REC/PLAY disc tray (CD-R/RW drive) is composed of the mechanism unit (HXL-3BSPA) and the boardass'y (HQA-030A).Therefore, in case of a write failure, check the following points first before proceeding to the next step.
The trouble is not due to the disc defect.
The FPC cable connecting the mechanism unit and the board ass'y is not disconnected or unplugged.
1. Symptoms, which may be due to a defect in the mechanism unit (HXL-3BSPA)
(1) There is no trace of writing on the CD-R/RW disc.(2) Error during write.
(3) Rotation stopped during write.(4) Write completes normally but the written disc cannot be reproduced.
(5) Either the CD-R or the CD-RW disc cannot be written onto.(6) Disc cannot be recognized as a recordable CD-R/RW disc.
(7) Abnormal noise from the mechanism during disc rotation.(8) Disc will not rotate.(9) Disc rotation is unstable (the rotation speed increases suddenly).
2. Symptoms, which may be due to a defect in the board ass'y (HQA-030A)
(1) Write operation will not start.(2) Disc will not rotate.
(3) The access LEDs do not light or blink.
Write operation
Front Key/Indicator operation
Press thePOWER button ON.
Are the keyoperations normal?
Are theindicators normal?
Front key and indicatoroperations are OK.
Are theconnections of the
CN001 andCN111 normal?
Check Front and
Control boards.
Connect the
CN001 and CN111.
YES
YES
YES
NO
NO NO
8/16/2019 Jvc Xr-d400sl Service En
13/28
XR-D40
Precaution for servicing
Handling of board ass'y in REC/PLAY disc tray
After replacing the board ass'y (HAQ-030A), be sure to modify it for use with the XR-D400SL by performing
the following operations:
1. Remove 3 condensers and confirm the jumper settings.2. Rewrite the firmware for XR-D400SL.
Note) The HQA-030A is not a part designed exclusively for the XR-D400.
1. Remove 3 condensers and confirm the jumper settings.
(1) Remove the condensers C429, C430 and C432 (for their locations, see Figs. 1 and 2).
[Fig. 1]
[Fig. 2]
[Fig. 3] [Fig. 4]
(2) Confirm the jumper settings.The settings should be as shown in Fig. 3 and 4. The jumper should be inserted into the rightmost hole
when the board is seen from the rear.
2. Rewrite the firmware for XR-D400
A PC and firmware software are required to rewrite the firmware.
Create a folder in the hard disk of the PC and store both of these in the same folder.
Applicable PC
Firmware software
OS Windows 95/98CPU Pentium 133 MHz or higherMemory 16 MB or moreModel IBM compatible machine
Firmware software Download.exe
Firmware Zcp133s.hex
8/16/2019 Jvc Xr-d400sl Service En
14/28
R-D400SL
14
Rewrite procedure
(1) Connect the REC/PLAY disc tray in the stand-alone mode to thePC. (Fig. 5)Note) The PC connection procedure will be described later.
(2) While holding down the switch on the right of the front panel(encircled in Fig. 5), boot the PC.
(3) Keep holding down the above switch until Windows has started up.
(4) Run firmware software Download.exe.
(5) When the firmware software screen appears (Fig. 6), confirm that;the Vendor is JVC, the product is XR-W4424 and the Version is 1.00.Note) If another content than the above is displayed, restart the operation
from step (2).
(6) After confirming that the BUS Type is ATAPI and that Create is checked, click the Updatebutton. (Fig. 6)
(7) When the screen as shown in Fig. 7 is displayed, select Zcp133s.hex, and click the OKbutton.
(8) The firmware rewriting starts and the access LED on the front panel changes from amber
lighting to amber blinking.Rewriting takes about 60 seconds. The extinction of the access LED indicates thecompletion of the firmware rewriting.
(9) When the screen in Fig. 6 is displayed again, click Close to close the firmware software.
[Fig. 5]
[Fig. 6]
[Fig. 8]
[Fig. 9]
[Fig. 7]
Firmware version check procedure(1) Boot the PC.
Note)If this procedure is started immediately after the rewriting procedure above, do notsimply restart the PC but be sure to switch it off and then on again.
(2) Open the Device Manager.Click [Start] R [SettingR [Control Panel] R [System].
Select [Device Manager] and click [CD-ROM].
(3) When the screen shown in Fig. 8 is displayed, select JVC XR-RWD400S.
(4) Open the Properties of JVC XR-RWD400S and select Setting.
(5) Confirm that the firmware revision number is 1.33. (Fig. 9)
8/16/2019 Jvc Xr-d400sl Service En
15/28
8/16/2019 Jvc Xr-d400sl Service En
16/28No.A0001
VICTOR COMPANY OF JAPAN, LIMITED
OPTICAL DISC BUSINESS DIV. PERSONAL & MOBILE NETWORK BUSINESS UNIT
AV & MULTIMEDIA COMPANY 1644, Shimotsuruma, Yamato, Kanagawa 242-8514, Japan
Printed in Ja200009 (S)
R-D400SL
8/16/2019 Jvc Xr-d400sl Service En
17/28
XR-D400SL
2-1
Block diagram
CD-ROM DRIVE ASSY POWER SUPPLY ASSY AC
Q AL02335 QA L0244 100V
POWER DC +12V(YELLOW)
SUPPLY
4 PIN DC +5V(RED)
ATAPI I/O
40 PIN
2 PIN
CD-R/RW DRIVE ASSY
CONTROL PCB ASSY FRONT PCB ASSY CN911
LOADER ASSY MAIN PCB ASSY LEA10014 CN501 LEA10012 S1034
HXL-3BSPA 27 PIN HQA-030 CN401 CN602 CN001 CN111 POWER SW
POWER ATAPI 21 PIN
SUB PCB UNIT CN107 CN407 SUPPLY I/O
IC101
IC101 u-COM
PRE AMP CN108 CN408 CN401 CN603 CN201 IC991 IC992
ATAPI 40 PIN ATAPI SCSI LED DRIVER
I/O I/O IC201 INTERFACE
CN101 27 PIN SCSI CONVERTER
50 PIN LED
LASER IC403 IC401
PICK-UP CN405 DAC S202 SCSI
ID SW
SPINDLE MOTOR CN401
FEED MOTOR 18 PIN J401
IC417 AUDIO OUT
LOADING MOTOR CN402 3 PIN
OPEN/CLOSE SW AUDIO OUT
CN401
LOADER UNIT 5 PIN
8/16/2019 Jvc Xr-d400sl Service En
18/28
8/16/2019 Jvc Xr-d400sl Service En
19/28
6
5
4
3
2
1
B C D E F G H I JA
7
XR-D400SL
2-3
Control circuit
8/16/2019 Jvc Xr-d400sl Service En
20/28
6
5
4
3
2
1
B C D E F G H I JA
7
XR-D400SL
2-4
Board interconnection
8/16/2019 Jvc Xr-d400sl Service En
21/28
6
5
4
3
2
1
B C D E F G H I JA
7
XR-D400SL
2-5
Printed circuit boards Control board
(Surface side)
TP311
TP309
TP187
TP310
TP100
T P 1 0 1 T P 1 0 2
T P 1 0 3 T P 1 0 4
TP105
TP106
TP107
TP108
TP109
TP110
T P 1 1 1
TP112
T P 1 1 3
TP114
TP115
T P 1 1 6 T P 1 1 7
T P 1 1 8
T P 1 1 9
T P 1 2 0
T P 1 2 1
T P 1 2 2
T P 1 2 3
TP124
TP125
TP126
TP127
TP128TP129TP130TP131
TP132
TP133TP134
TP135
TP136
TP137
TP138
TP139 TP140
TP141
TP142
TP143
TP144
TP145
TP146
TP147
TP148
TP149
TP150
TP151
TP152
T P 1 5 3
T P 1 5 4
TP155
TP156
TP157
T P 1 5 8
TP159TP160
TP161
TP162
TP163
TP164
TP165
TP166
TP167
TP168
T P 1 6 9
T P 1 7 0
T P 1 7 1 T P 1 7 2
T P 1 7 3 T P 1 7 4
T P 1 7 5 T P 1 7 6
TP177
TP179
TP180
TP181
TP182
TP183
TP184
TP185
TP186
TP188
TP189
TP190
TP191
TP192
TP193
TP197
TP198
TP199
TP201
TP202
TP203
TP204
T P 2 0 5
T P 2 0 6
TP207
T P 2 0 8
T P 2 0 9
T P 2 1 0
T P 2 1 1
T P 2 1 2
T P 2 1 3
T P 2 1 4
T P 2 1 5
T P 2 1 6
T P 2 1 7
T P 2 1 8
T P 2 1 9
T P 2 2 0
T P 2 2 1
T P 2 2 2
T P 2 2 3
T P 2 2 4
T P 2 2 5
TP226
T P 2 2 7
TP228
TP229 T P 2 3 0
TP231
T P 2 3 2
TP233
T P 2 3 4
TP235
TP236
TP237
TP238
T P 2 3 9
TP240TP241
T P 2 4 2
TP243
T P 2 4 4
TP245
TP246
T P 2 4 7
T P 2 4 8
TP249
TP250TP251
TP252
T P 2 5 3
TP254
T P 2 5 6
TP257
T P 2 5 8
T P 2 5 9
TP301
TP302
TP303
TP304
TP305
TP306
TP307
TP308
TP401
TP402
TP403
TP404
TP405
TP406
TP407
TP408
TP409
TP410
TP411
TP412
TP413
TP414
TP415
TP416
TP417
TP418
TP419
TP420
TP421
TP422
TP423 TP424
TP425
TP426
TP501 TP502
TP503
TP504
TP505TP507
TP509
T P 6 0 1
T P 6 0 2
T P 6 0 3
T P 6 0 4
T P 6 0 5
TP606
TP607
TP608
T P 6 0 9
TP610
T P 6 1 1
TP613
TP431
TP616
TP617
TP618
TP619
CN202
T P 6 2 1
T P 6 2 2
T P 6 2 3
T P 6 2 4
T P 6 2 6
T P 6 2 7
T P 6 2 8
T P 6 2 9
T P 6 3 0
T P 6 3 1
T P 6 3 2
T P 6 3 3
T P 6 3 4
T P 6 3 5
T P 6 3 6
T P 6 3 7
T P 6 3 8
T P 6 3 9
T P 6 4 0
T P 6 4 1
T P 6 4 2
T P 6 4 3
T P 6 4 4
T P 6 4 5
T P 6 4 6
T P 6 4 7
T P 6 4 8
T P 6 4 9
T P 6 5 0
T P 6 5 1
T P 6 5 2
T P 6 5 3
T P 6 5 4
T P 6 5 5
T P 6 5 6
T P 6 5 7
T P 6 5 8
T P 6 5 9
T P 6 6 0
T
P 6 6 1
T P 6 6 2
T P 6 6 3
T P 6 6 4
T P 6 6 5
T P 6 6 6
T P 6 6 7
T P 6 6 8
T P 6 6 9
T P 6 7 0
T P 6 7 1
T P 6 7 2
T P 6 7 3
T P 6 7 4
T P 6 7 5
T P 6 7 6
T P 6 7 7
T P 6 7 8
TP679
T P 6 8 0
TP432
TP625
T P 2 6 0
TP433
TP681
TP682
TP261
T P 5 1 2
TP683
TP684
TP685
TP262
TP264
TP265
TP511
T P6 15 T P6 1 2
TP614
TP620
(Bottom side)
8/16/2019 Jvc Xr-d400sl Service En
22/28
6
5
4
3
2
1
B C D E F G H I JA
7
XR-D400SL
2-6
C1101
C1102
C1104
C1105
CN111
D 10 01 D 10 02 D1003 D1004 D 10 05 D 10 06 D1 007 D1008 D1009 D1010
D1011
D1012
D1013D1014 D1015 D1 01 6 D 10 17 D1 01 8 D 10 19 D1020 D1021
D1022
D1023 D1024 D1025
D1026 D1027 D1028
D1029
D1030
D1031
D 1 0 3 2
I C 9 9 1
I C 9 9 2
Q1011Q1012
Q1013 Q1014
Q1015
Q1016
Q1017
Q1018
Q1019
Q1020
Q1031
Q1032
R1001 R1002 R1003 R1004 R1005 R1006 R1007 R1008 R1009 R1010
R1011 R 1012 R1013 R1014R 1 0 1 5
R1016R1017
R1018R1019
R 1 0 2 0 R1021
R1022
R1023 R1024 R1025
R1026 R 10 2 7 R 1 02 8
R1029
R1030
R1031
R1032
R1101
R1102
R1103
S 10 01 S 10 02 S1003 S1004 S1005S1006S1007S1008 S1009 S1010
S1011S1012S1013 S1014 S1015 S1016 S1017S1018S1019S1020
S1021
S1022
S1023S1024
S1025
S1026
S1027 S1028S1029S1030S1031S1032
S1034
T P 9 0 1
TP902
TP903
T P 9 0 4
T P 9 0 5
T P 9 0 6
T P 9 0 7
T P 9 0 8 T
P 9 0 9
T P 9 1 0
T P 9 1 1
T P 9 1 2
T P 9 1 3
T P 9 1 4
T P 9 1 5
T P 9 1 6
T P 9 1 7
T P 9 1 8
T P 9 1 9
T P 9 2 0
T P 9 2 1
T P 9 2 2
T P 9 2 3
T P 9 2 4
TP925
T P 9 2 6
TP927
TP928
TP929
TP930
TP931T P 9 3 2
TP933T P 9 3 4
TP935
TP936
T P 9 3 7
TP938
TP939
T P 9 4 0
TP941
T P 9 4 2
TP943
TP944
T P 9 4 5
TP946
TP947
TP948
TP949 TP950
TP951T P 9 5 2
TP953
TP954
TP955
TP956
T P 9 5 7
TP958 T
P 9 5 9
T P 9 6 0
T P 9 6 1
TP962
TP963 TP964
T P 9 6 5
TP966
TP967
TP968TP969
T P 9 7 0
T P 9 7 1
TP972
TP973
TP974
TP975
TP976
TP977
CN991
Front board
8/16/2019 Jvc Xr-d400sl Service En
23/28
XR-D40
PARTS LIST
[ XR-D400SL ]
- Contents -
Exploded view of general assembly and parts listCR-R/RW mechanism assembly and parts list
Packing materials and accessories parts list
3-33-5
3-6
Area suffix
E ----------------- Germany
8/16/2019 Jvc Xr-d400sl Service En
24/28
R-D400SL
2
MEMO
8/16/2019 Jvc Xr-d400sl Service En
25/28
XR-D400SL
3-3
2
5
4
16
20
3
1517 13
12
20
25
35
24
21
21
7
829
30
32
27
38
40
20
9
33
33
34
31
23
41
42
28
18
16
1
10
11
14
6
22
Exploded view of general assembly and parts list
26
26
19
19
37
3736
36
20
20
26
20
20
2026
Block No. M1MM
8/16/2019 Jvc Xr-d400sl Service En
26/28
XR-D400SL
3-4
Item Parts number Parts name AreaA
Parts list ( General Assembly )
Q'ty Description
Block No.
01 LE10227-001B FRONT PANEL 1
02 LE30810-005A WINDOW SCREEN 1
03 E75896-228 SPACER 2
04 LE20500-002A DO OR 1
05 LE20506-001A DOOR(ROM) 1
06 LE40651-001A TEN.SPRING 2
07 LE10226-001B CHASSIS BASE 1
08 E47227-008 FO O T 2
09 QYSBSG3010M T.SCREW 2
10 LE30818-002A PUSH BUTTON(5) 1
11 LE40650-002A COMP.SPRING 1
12 LE20498-001A PUSH BUTTON(1) 1
13 LE20499-002A PUSH BUTTON(2) 1
14 LE30814-001A P BUTTON(3)ASSY 1
15 LE30817-001A PUSH BUTTON(4) 2
16 LE30812-001A INDICATOR(1) 4
17 LE30813-001A INDICATOR(2) 1
18 LE30840-001A INDICATOR(4) 20
19 QYSBSF2608Z T.SCREW 13
20 QYSBSG3008Z T.SCREW 17
21 LE20503-001B SIDE BKT 2
22 LE40729-001A LUG 1
23 --- CD-ROM DRIVE 1
24 QAL0235-001 CD-ROM DRIVE 1
25 LE20505-001A FITTING 1
26 QYSPSP3006Z T.SCREW 8
27 LE20504-001B PCB BKT 1
28 QAL0244-002 P OWE R P CBA 1
29 LE20496-001A REAR PANEL 1
30 WJ Z004 8-0 02A A C I NL ETA 1
31 QYBNSP4008M BOLT 1
32 QYNFS4000Z NUT 1
33 QYSBSGY3008M SPECIAL SCREW 6
34 QYSHSP3006N T.SCREW 2
35 LE20497-002A METAL COVER 1
36 QYSBSGY3008N SPECIAL SCREW 4
37 E406308-004 SPECIAL SCREW 4
38 QUQ412-2118CJ FLAT WIRE 1
40 L EA10012-01A FRO NT P WB A SSY 1
41 L EA10014-01A CONTRL PWB ASSY 1
42 WJJ0150-001A WIRE ASSY 1
See Page 3-5
8/16/2019 Jvc Xr-d400sl Service En
27/28
XR-D40
Item Parts number Parts name AreaA
Parts list
Q'ty Description
Block No. M2MM
01 HQ200031-001 UPPER CASE 1
02 HQ200032-001 BOTTOM COVER 1
03 HXL-3BSPA LOADER MECHA 1
04 QUQ105-2705AB FLAT WIRE 2
05 HQ400090-001 INSULATOR SHEET 1
06 HQA-030A MAIN.P.C.B.ASSY 1
07 HQ400127-001 INSULATOR 4
08 HQ400089-001 INSULATOR 4
09 HQZ0073-001 SIL ICON SHEET 2
10 HQ400113-001 SPECIAL SCREW 4
11 SSSP2004N SC R EW 6
See page 1-13
C N 1 0 8
C N 1 0 7
5
77
2
9
6
4
10
10
3
8
11
11
1
Block No. M2MM
CD-R/RW mechanism assembly and parts list
8/16/2019 Jvc Xr-d400sl Service En
28/28
R-D400SL
Packing materials and accessories parts listBlock No. M3MMBlock No. M4MM
6
1
2
4
3
5
Item Parts number Parts name AreaA
Packing list
Q'ty Description
Block No. M3MM
1 LE10236-001A P.CASE 1
2 LE20509-001A P.PAD(L) 1
3 LE20508-001A P.PAD(U) 1
4 QPC05006515P POLY BAG 1
5 LE30830-201A PARTSBOX 1
6 LE40681-001A ACCESSORY LABEL 1
Item Parts number Parts name AreaA
Accessories parts list
Q'ty Description
Block No. M4MM
1 LET0169-001A I.BOOK 1
2 LET0174-001A I.BOOK 1
3 QMPL110-200-JQ PO WE R C OR DA 1
4 EWP302-011W SIGNAL CORD 1
5 BT-54008-2 WARRANTY CARD 1
6 LE40732 003A CAUTION SHEET 1