Jvc Av4300 Projection Tv Sm

This file is provided FREE OF CHARGE from the electromaniacs.com community You are free to distribute this file to other persons who needs it , but without of charge Also on http://electromaniacs.com you can find thousands of service manuals , schematics free of charge

No.51876 Mar. 2002

AV-4300AV-5000

1COPYRIGHT 2002 VICTOR COMPANY OF JAPAN, LTD.

AV-4300 AV-5000AV-4300 / EE AV-5000 / EE

CONTENTS! SPECIFICATIONS 2

! SAFETY PRECAUTIONS 3! MAIN DIFFERENCE LIST 5

! FUNCTIONS 6

! SPECIFIC SERVICE INSTRUCTIONS 7

! SERVICE ADJUSTMENTS 15

! TROUBLESHOOTING 32

! PARTS LIST 41

STANDARD CIRCUIT DIAGRAM (APPENDED) 2-1

SERVICE MANUALREAR PROJECTION TELEVISION

No.51876

AV-4300AV-5000

2

SPECIFICATIONSItems Contents

Dimensions (WHD) 94.7cm 123.6cm 46.1cm [AV-4300]111.9cm 136.2cm 53.0cm [AV-5000]

Mass 56kg [AV-4300]

60kg [AV-5000]

TV System and Color system

PAL

SECAM

NT SC

External input

PAL / SECAM / NTSC (3.58 / 4.43)

B / G / D / K / H / I

B / G / D / K / K

M

NTSC50Hz / NTSC3.58 / NTSC4.43 / PAL60Hz / SECAM60Hz

TV Receiving Channels and Frequency

Program Selection Channel

44MHz - 870MHz

100 Channels

Intermediate Frequency Video IF : 38.9MHz

Multi-sound System NICAM [UK system]

A2 [Germany system]

Teletext System English based

Power Input AC 220V 240V, 50Hz / 60Hz

Power Consumption Average 219W (operating)

Projection Tube 7-inch tube 3 (R/G/B)Projection Tube High Voltage 30.0kV

Screen Transparent screen (united Fresnel lens & Double lenticular lens, with shield)

Aspect ratio 4:3

Screen Size 43-inch (109cm) : measured diagonally [W: 87.4cm H: 65.6cm]

Speaker Front (L/R) : 12cm round type 2, 5cm round type 2Center : 7.5cm round type 2

Audio Power Output Front (L/R) : 10W+10W

Center : 5W +5W

Antenna Input Terminal 75 unbalanced, aerial-type connector 1Input Terminal (INPUT 1 / 2 / 3)

VIDEO

AUDIO (L/R)

S-VIDEO

COMPONENT

[INPUT 2]

1V(p-p), 75 RCA pin jack 3500mV(rms), 47k RCA pin jack 6Mini-DIN 4-pin connector 3Y : 1V(p-p), 75C : 0.286V(p-p), 75Y / CB / CR

RCA pin jack 3

Output Terminal (MONITOR OUT)

Video

Audio (L/R)

S-Video

1V(p-p), 75 RCA pin jack 1470mV(rms), 1k RCA pin jack 2mini-DIN 4-pin jack 1Y : 1V(p-p) positive, 75 (negat ive sync. provided)C : 0.286V(p-p), 75 (burst s ignal)

Audio Output Terminal (AUDIO TO HI-FI) FRONT / REAR : Variable RCA pin jack 4

Speaker Output Terminal (REAR SPEAKER) L / R : 5W2, 8

Headphone output 3.5mm mini jack (stereo type)

Remote Control Unit 5652138A (Dry cell battery : AA/R6/UM-3 2)

No. 51876

AV-4300AV-5000

3

SAFETY PRECAUTIONS

(2)

(2)

(3)

(4)

(5)

(6)

(7)

No. 51876

AV-4300AV-5000

4

(9)

!

Shie ld pl ate C

No. 51876

AV-4300AV-5000

5

!

MAIN DIFFERENCE LISTItem AV-4300 AV-4300 /EE AV- 5000 AV- 5000 /EE Remarks

CONVERGENCE ADJUSTMENT For Asia area For Russia For Asia area For Russia

RATING LABEL 7936261A 7936301A 7936203A 7936302A

GOST LABEL ---------- 7944081A ---------- 7944081A EE only

OPERATION MANUAL 7910445A 7910478A 7910445A 7910478A

No. 51876

AV-4300AV-5000

6

FUNCTIONS

< FRONT CONTORL PANEL >

< REAR TERMINAL PANEL >

No. 51876

AV-4300AV-5000

7

SPECIFIC SERVICE INSTRUCTIONSDISASSEMBLE PROCEDURE Refer to EXPLODE VIEW in PARTS LIST (page 43 and 44) .

BOTTOM BACK COVER Be sure to disconnect the power plug.

1. Remove sixteen screws [No.40] from the bottom back cover [No.9]2. Be careful of the power plug to remove the bottom back cover.

FRONT PANEL Be careful not to damage the front panel.

1. Remove three screws from the pedestal [No.15] and take it down.2. Remove the screws on the speaker grill and take it down.

SPEAKER1. Remove four screws used for the speakers fixing.2. Remove the speakers wanted and the connected wire from the back of the speaker.

3. Take the speakers down.

PWB1. Remove the screws f ixed PW B and the holder [No.11].2. Separate all of the connec ted wires from the f ixed lead clampers.

3. Drag the main chassis PWB backwards slowly.4. Set it up when dragging the main chassis PWB outwards.

5. Be sure that all of the ready connec ted wires can be checked when ON-OFF switch is on.

In order to set the PWB up easily, if necessary, some concerned connected wires are allowed to disconnect temporarily, then revive their

connec tion.

The stability would be not good when the PWB is set up. Be careful not to let it down.

Before the power is on, make sure that each connected wire are ready ,and prevent the PWB from the outside objects so as to avoid the

short circuit .

PRT (PROJECTION TUBE) Take care of the surface of lens1. Remove the back cover [No.1].

Disassemble method for 43 top back coverDisassemble 13 screws [No.40] on the top back cover [No.1] and pull out the cover and take it down.

Disassemble method for 50 top frame [No.7]Disassemble 16 screws [No.40] on the top back cover [No.1] and four screws fixed on the holder for the front frame, then take it down.

Never take the top back cover [No.1] down." Please protect the front frame from pulling out when removing the screws of the back cover.)

4. Removal of CPT board [F] and the earth of PRT.5. Reelingly pull three of anode wires out of FBT.

6. Loosen the fastening screws on VM MAGNET to take down VM MAGNET.7. Loosen the fastening screw on DY to take DY down.

8. Loosen the lead clampers that need separating, so that the anode wires are out of binding.9. Disassemble 4 screws of PRT [No.24] or [No.25], [No.26] needed to take out and lift up the metal board with PTV slowly, then pull out the

PRT together with the anode wire.

10.Remove 4 screws from lens [No.21] or [No.22], [No.23] connected with PRT, and take down the lens. Also the step can be carried out prior tothe removal of PRT.

MIRROR1. Remove fifteen screws from the mirror support [No.3] or [No.4], [No.5] on the mirror.

2. Take Down the mirror.

In the process of removal, protect the mirror f rom crack ing.

After f inishing maintenance, the parts disassembled should be returned to the original state.

No. 51876

AV-4300AV-5000

8

Fig. A

Fig. B

No. 51876

AV-4300AV-5000

9

Disconnect the # pin of 1905 from +B line.

Connect jig (15kVR) between +B line and # pin of 1905.

Fig.2 Deflection/Power PWB

Fig.1

No. 51876

AV-4300AV-5000

10

No. 51876

AV-4300AV-5000

11

No. 51876

AV-4300AV-5000

12

Chip Components

No. 51876

AV-4300AV-5000

13

No. 51876

AV-4300AV-5000

14

#

No. 51876

AV-4300AV-5000

15

SERVICE ADJUSTMENTSADJUSTMENT PREPARATION1. You can make the necessary adjustments for this unit with either the Remote control unit or with the adjustment tools and parts as

given below.

2. Ad justment with the Remote control unit is made on the basis of the initial setting values, however, the new setting values whichset the screen to its optimum condition may differ from the initial settings.

3. Make sure that AC power is turned on correc tly.4. Turn on the power for set and tes t equipment before use, and start the adjustment procedures after wait ing at least 30 minutes.

5. Un less otherwise specified, prepare the most suitable reception or input signal for adjustment.6. Never touch any adjustment parts which are not spec if ied in the list for this adjus tment - variable resistors, t ransformers, condensers, etc.

7. Presetting before adjustment. Unless otherwise specified in the adjustment instruct ions, preset the following functions with the remote control unit.

ADJUSTMENT EQUIPMENT1. DC voltmeter (or digital voltmeter)

2. Oscilloscope

3. Signal generator (Pattern generator)PAL/SECAM/NTSC

4. Remote control unit

ADJUSTMENT LOCATIONS

1. CENTERING MAGNET

: FOR RED PRT

2. CENTERING MAGNET

: FOR GREEN PRT

3. CENTERING MAGNET

: FOR BLUE PRT

4. 4-POLE MAGNET

: FOR BEAM FORM ADJUSTMENT

5. 2-POLE MAGNET

: FOR BEAM ALIGNMENT

6. FOCUS PACK

R CPT P.W.B G CPT P.W.B B CPT P.W.B

No. 51876

AV-4300AV-5000

16

SIG

NA

L P.W.B

PO

WE

R / D

EF

LEC

TION

P.W.B

.

No. 51876

AV-4300AV-5000

17

BASIC OPERATION OF SERVICE MENU (VIDEO ADUSTMENT MODE)

$ %

CHANGE THE SETT ING (ADJUSTMENT) VALUE

: [&(LEFT)] / ['(RUGHT)] buttons

$ %

'

NOTE :1. If there is a different value than shown in the table (page 18) for fixed data,

adjust it using [&(LEFT)] / ['(RUGHT)] buttons.

2. When exchanging microprocessor and TV is turned on for first time, itrequires initializat ion of VIDEO / CHROMA ADJ.

3. This DATA has PAL and NT SC modes (2 modes).

MODE SWREG1 18

REG2 08

SET1 00

SET2 00

ADJ.

SERV 00 BELL 80

SBRT 80 BADJ 08

INIT 00 RADJ 08

ADJ.

CSYS 03 SCOL 0A

CTRA 00 SCNT 0

CSW 00 STIT 4C

HPOS 10 SSHA 38

AFCG 00 EBRT 40

VFRQ 00 ECNT 60

VPOS 00 HBLK 00

PMUT 01 VBLK 00

ADJ.

WPDL 01 RYLE 00HBRT 01 GYLE 03

COLG 00 YDL 00

CLT 00 STRA 01

TACL 01 APFO 00

CDE 01 OACL 01

GPPH 01 TOFF 00

RYPH 03 TOFQ 00

ADJ.

DTCP 00 BLC 01

DTCR 00 BDL 00

BEPL 00 BSG 00

BEP1 05 BARE 00

BEP2 00 DABP 00

DTCL 00 DABG 07

WHTP 00 ABLP 03

BLS 00 ABLG 05

ADJ.

TVSW 03 15SW 01

VENH 04 ATT 01

CBPF 01 IDSN 00

KLAR 00 SGP 00

LINE 00 VID 00

CORG 00 HID 00

PLL 00 ID 01

BELM 01

< SERVICE MENU screen >

Page 1

Page 2

Page 3

Page 4

Page 5

Page 6

No. 51876

AV-4300AV-5000

18

SERVICE MENU INITIAL SETTING VALUEInitial value Initial value

Page Menu ItemPAL NT SC

Remarks Page Menu ItemPAL NT SC

Remarks

1 REG1 18 5 ADJ. DTCP 00 DC TRANSIT CORRECTION POINTMODE

SW REG2 08 DTCR 00 DC TRANSIT CORRECTION RATIO

SET1 00 BEPL 00 BLACK EXPANDED POINT LIMITER

SET2 00 BEP1 05 BLACK EXPANDE D POINT 1

2 ADJ. SERV 00 SERVICE BEP2 00 BLACK EXP ANDED POINT 2

SBRT 80 SUB BRIGHT DTCL 00 DC TRANSIT CORRECTION LEVEL

INIT 00 INITIAL SET WHTP 00 WHITE PEAK DET CURRENT

BELL 80 BELL FILTER ADJ BLS 00 BLACK LEVEL CORRE CTION1

BADJ 08 B-Y BLACK ADJ BLC 01 BLACK LEVEL CORRE CTION2

RADJ 08 R-Y BLACK ADJ BDL 00 BLACK DET LEVEL

3 ADJ. CSYS 03 COLOR SYSTEM BSG 00 BLACK EXPANDED AREA

CTRA 00 CHROMA TRAP BARE 00 BLACK EXPANDED AREA

CSW 00 CHROMA SW DABP 00 DYNAMIC ABL POINT

HPOS 10 13 H POSITION DABG 07 DYNAMIC ABL GAIN

AFCG 00 AFC G ABLP 03 ABL POINT

VFRQ 00 V FREQUENCY ABLG 05 ABL GAIN

VPOS 00 V POSITION 6 ADJ. TVSW 03 SYSTEM SEL

PMUT 01 PICTURE MUTE VENH 04 V ENHANCE L EVEL

SCOL 0A SUB COLOR CBPF 01 CHROMA BPF

SCNT 10 SUB CONTRAST KLAR 00 KILLER

STIT 40 SUB TINT LINE 00 1 LINE DOT

SSHA 38 SUB SHARP CORG 00 CORING

EBRT 40 EXT RGB BRIGHT PLL 00 PLL SEL

ECNT 60 EXT RGB CONTRAST 15SW 01 DAC

HBLK 00 B BLK END PHASE ATT 01 ATT

VBLK 00 V BLK PHASE IDSN 00 SECAM-ID4 ADJ. WPDL 01 WHITE PEAK DET LEVEL SGP 00 SECAM-GP

HBRT 01 HI BRT COLOR VID 00 V-IDCOLG 00 COLOR HID 00 H-IDCLT 00 COLOR LIMITER LEVEL ID 01 ID KEYTACL 01 TXACL BELM 01 BELL MONITOR

CDE 01 COLOR DETAIL ENHANCEMENT

GPPH 01 GP PHASE

RYPH 03 R-Y PHASE

PYLE 00 R/B LEVEL

GYLE 03 G/B LEVEL

YDL 00 Y DELAY

STRA 01 SHARPNESS TRAC

APFO 00 APACON PEAK f

OACL 01 OSD ACL

TOFF 00 TOF f

TOFQ 00 TOF Q

No. 51876

AV-4300AV-5000

19

ADJUSTMENT STEP

1. ASSEMBLED P.W.B. ADJUSTMENT1.1 AFC Alignment 201.2 AGC Alignment 20

1.3 A2 & NICAM Operation Check 201.4 SECAM Bell Filter Adjustment 20

1.5 SECAM White Balance Adjustment 21

1.6 Comb Filter Operat ion Check 21

2. FINAL ASSEMBLY ADJUSTMENT2.1 Lens Focus Adjustment 222.2 White Balance Adjustment 23

2.3 Sub Brightness Adjustment 242.4 Surround Operation Check 24

2.4.1 Stereo Off Check 242.4.2 Stereo Off / Monaural Check 24

2.4.3 Stadium Surround Check 252.4.4 Stadium Surround/Monaural Check 25

2.4.5 Concert Surround Check 252.4.6 Concert Hall Surround/Monaural Check 25

2.4.7 Dolby Pro-logic Check 252.4.8 Dolby Pro-logic / Monaural Check 25

2.5 Raster Inclination Adjustment (Deflect ion Yoke) 262.6 Raster Position Adjustment 26

2.7 Vertical Size Adjustment (R630) 262.8 Horizontal Size Adjustment (R603) 27

2.9 Beam Alignment 272.10 Beam Shape Adjustment 28

2.11 Static Focus Adjustment 282.12 Blue Defocus Adjus tment 28

2.13 Digital Convergence Adjustment 292.13.1Raster Position Adjustment 30

2.13.2Convergence Point Adjustment 302.14 Sub Picture (P IN P) Adjustment 31

No. 51876

AV-4300AV-5000

20

1. ASSEMBLED P.W.B. ADJUSTMENT1.1 AFC Alignment

Ad justment Preparation1. Apply relevant RF signal (a) CH05 (fp=85.25MHz). Apply

heat run for more than 30 minutes to avoid inf luence of

circuit temperature drift .2. The SOUND SYSTEM is selected to D/K standard.

3. Receive the CH05 using frequency direc t of SETUP Menuto ensure AFC loop is OFF.

4. Connect oscilloscope and voltmeter to pin 4 PTP connectorof SIGNAL P.W.B.

5. Adjust L202 until fast rate of change is seen on theoscilloscope.

6. Adjust L202 so that the voltmeter reads 2.5V0.2V.

1.2 AGC AlignmentAd justment Preparation

1. After received the signal, apply heat run for more than tenminutes to avoid the influence of circuit temperature drift.

2. Connect a voltmeter of at least 100K ohm internalresistance to the AGC terminal (pin 1 PTP connec tor).

3. Received the channel below.4. Adjust AGC potentiometer R245 until the following voltage

is obtained.

Received signal

Ch LevelSetting Voltage( V)

05-56dBm

(+53dBV 75ohm terminated)

Maximum Voltage

- (1.0V0.1V)[about 8V]

< Main IF Adjustment Point >

1.3 A2 & NICAM Operation CheckAd justment Preparation1. Received the A2 or NICAM stereo broadcast.

2. Set the SURROUND mode to STEREO.

OSD ExpressionCheck OSD expression is changed as follows.

Audio Mode is selected by remote controller.

1.4 SECAM Bell Filter AdjustmentAd justment Preparation

1. Receive the SECAM Philips pattern signal or color barsignal.

2. Connect the probe to pin 21 of I503 at signal Sub P.W.B.(asshown in figure below).

3. Set to CSYS DATA: 06, TVSW DATA: 05, CTRA DATA:01, 15SW DATA: 00 of V/C I2C ADJUST MODE.

Ad justment Procedure1. Adjust the waveform at pin 21 of I503, amplitude must

match at each horizontal cycle by BELL of V/C I2CADJUST MODE.

No. 51876

AV-4300AV-5000

21

1.5 SECAM White Balance AdjustmentAd justment Preparation

1. SECAM BELL FILTER adjustment should be finished.2. Receive the SECAM Philips pattern signal or color bar

signal.

3. Connect the probe to C536 (R-Y). C537 (B-Y) at Signal SubP.W.B (Refer to f igure below).

4. Set to "CSYS" DATA: 06, "TVSW" DATA: 05, "CTRA"DATA: 01, "15SW" DATA: 00 of V/C I2C ADJUST MODE.

Ad justment Procedure

1. Adjustment signal level as shown below by "RADJ" "BAD J"of V/C I2 C ADJUST MODE.

* REMARK

After Adjustment (1.5 and 1.6) I2C DATA Reset.

"CSYS" : 06 03

"TVSW" : 05 03

"CTRA" : 01 00

"15SW" : 00 01

1.6 Comb Filter Operation CheckAdjustment Preparation

1. Receive the PAL Philips pattern signal.2. Select the PICTURE option using ['] button.3. Select PERSONAL [SET UP] opt ion using [' ] button.

4. Select the COMB FILTER mode by press ing [%] / [$]button.

Ad justment Procedure1. Set the COMB FILTER : ON by pressing ['] button, and

check the COMB FILTER operation as shown in the figurebelow.

2. Set the COMB FILTER : OFF by pressing ['] button, and

check the COMB FILTER operat ion as shown in the figurebelow.

line dots : a little

PAL (Philips pattern)

NON CROSS COLOR

No. 51876

AV-4300AV-5000

22

2. FINAL ASSEMBLY ADJUSTMENT2.1 Lens Focus Adjustment

Ad justment Preparation1. The orientation of PTV set is arbitrary west, east, north and

south.

2. Centering DY inclination should have been adjusted.3. Electrical focus adjustment should have been completed.

4. Drive VR locat ion adjustment should have been completed(Red: 12 O'clock).

5. Receive the cross-hatch pattern signal.6. Refer to setup below.

(CONT RAST : 10 times PUSH button from full scale tolower side.(BRIGHTNESS : minimum

Ad justment Procedure1. Loosen the wing nuts on the lens cylinder so that the lens

cylinder can be turned. (Be careful not to loosen too much).After completing steps (4), (5) and (6) below. Tightening the

wing nuts for each lens with a torque of 1.18Nm (12Kgfcm)~ 1.67Nm (17Kgfcm). (Be careful the lens cylinder not

turning after having tighten wing nuts. But if it is tighten toomuch, lens is too t ilt or broken a screw.)

2. Apply covers to each colors of R, G and B lenses andprojec t a single color on the screen and adjust in sequence.(The adjustment order of R, G and B is only an example.)

3. If the lens adjustment knob is turned clockwise viewed fromthe front, the color aberration change as follows .

Change of color aberrationLens

Short focus Long focus

RED LENS Orange Scarlet

GREEN LENS Blue Red

BLUE LENS Purple Green

4. In case of G lensSet to the point where the chromatic aberration switches from

blue to red. If the chromatic aberrat ion appearing all over thescreen in not the same, observe the vertical bright line andadjust lens focus as spec if ied in table below. When the red

chromatic aberration appearing at both sides of the bright line

is not equal, observe the side with larger chromatic aberrationwhen adjusting.

OPTICAL FOCUSING ADJUSTMENT GREEN

ITEM UNIT

SCREEN SIZE 50" 43" INCH

LI AND L2

(PITCHES from CENTER)

4.0 4.0 CROSS

HATCHPITCHES

BETWEEN

L1 & L2

* *

I * *COLORABERRATION O ** **

REFFER

TONOTE

BELOW

NOTE : * Slightly reddish or no color

** Slightly bluish or no color

Change the signal to the circle pattern and fine adjust.

Observe the corner part of the screen, especially observenumber is the small circle when adjusting. If the focus

performance at the sc reen exceeds the lower limit, it isacceptable.

NOTE :

1. Since the G light is very important for picture quality andperformance, pay special attention in its adjustment.

2. Be careful not to touch the lens with your f ingers whenadjusting.

Cross-hatchColor aberration

Small circle of circle pattern

No. 51876

AV-4300AV-5000

23

5. In case of R lensSet the position where the chromatic aberration change from

orange to scarlet. As shown below, observe the vert ical brightline and adjust lens focus where the scarlet or orangechromatic aberration slightly appears inside and scarlet or

orange outside (reference value :1~3mm) at the point specified

in table below .Change the signal and f ine -adjust in the same way as the G

lens.

OPTICAL FOCUSING ADJUSTMENT REDITEM UNIT


L1 AND L2

(PITCHES fromCENTER)

0.0

center

0.0

center

CROSS

HATCHPITCHES

L

side

- -


REFFER

TONOTE

BELOW

NOTE : * Slightly orange or no color** Slightly scarlet or no color

6. In case of B lensSet the position where the chromatic aberration change from

purple to green. As shown below, observe the vert ical brightline and adjust lens focus where the purple or green chromatic

aberration slightly appears inside and purple or green outside(reference value: 1~3mm) at the points specif ied in table below.

Change the signal and f ine -adjust in the same way as the Glens.

OPTICAL FOCUSING ADJUSTMENT BLUE

ITEM UNIT


LI AND L2

(PITCHES fromCENTER)

0.0

center

0.0

center

CROSS

HATCHPITCHES

L

side

- -


REFFER

TONOTE

BELOW

NOTE : * Slightly purplish or no color

** Slightly greenish or no color

7. After all colors have been adjusted, display all colors withthe cross -hatch pattern signal and compare the focus

(opt ical focus) performance with the limit sample test.

2.2 White Balance Adjustment1. Screen adjustment

2. High brightness white balance

3. Low brightness balance

Screen adjustment VRs Drive adjustment VRsRed : on FOCUS PACK Red : R873

Green : on FOCUS PACK Green : R843

Blue : on FOCUS PACK

Ad justment Preparation1. Start adjustment 20 minutes or more after the power is

turned ON.

2. The vertical incident illuminat ion on the screen should be20lux or less.

3. Set the video settings (contrast: max, others: center) tostandard condition.

4. For low brightness white balance adjustment, input a whiteraster s ignal level of 0.300Vp-p (Video input level).

5. For high brightness white balance adjus tment, input a whiteraster s ignal level of 0.715Vp-p(Video input level).

6. Set the drive adjustment VRs (red and green) to 12-2o'clock position.

7. Turn the sc reen adjustment VRs (red, green and blue) fullycounterclockwise.

8. Set video advanced setting white control to COOL position.Ad justment procedure

1. Go to VIDEO CHROMA ADJUST mode by pressingTV/VIDEO and power button on Control Panel at the same

time.2. In "SERVICE" mode push the ['] button and sc reen turns

to black, Gradually turn the screen adjustment VRs (red,green blue) clockwise and set them where the red, green

and blue slightly bright lines just appear evenly on thescreen.

3. Push the ['] button again to return to Normal side.4. Press MENU button to exit VIDEO CHROMA ADJUST .

Select the input s ignal for high brightness (Video level=0.715Vp-p).

5. Adjust the high brightness white balance using the driveadjustment VRs (red, green).

6. Select the s ignal for low brightness (Video level = 0.300Vp-p).

7. Adjust the low brightness white balance using the sc reenadjustment VRs (red, green and blue).

8. Check that high brightness white balance is obtained, If it isdoes not, return to step (7).

NOTE :Before adjust ing the White Balance, check that the screenadjustment VRs are turned fully counterclockwise. Since the

phosphorescent surface of the CRT is likely to be burned, becareful.

White balance = 10400K + 10 MPCDColor Coord inate = x : 0.276 / y : 0.293

No. 51876

AV-4300AV-5000

24

2.3 Sub Brightness AdjustmentAd justment Preparation

1. Start adjustment 20minutes or more after the power isturned ON, Receive the color bar signal.

2. Set the contrast and color controls to minimum.

3. The ambient illumination on the sc reen should be 20 lux orless.

W75% Y CY G MG R BL

A7 A6 A5 A4 A3 A2 A1

b

c

d

Q I W 100% BLK


1. Go to Sub-Brightness adjustment in VIDEO CHROMAADJUST mode (press input and Power button on Control

panel at the same t ime), [%]/[$] buttons and then using[&]/['] button.

2. Then adjust Sub-Brightness using [&]/[' ] buttons toincrease or decrease the value (Visually adjust).

3. After adjus tment, press the MENU button to exit VIDEOCHROMA ADJUST mode (Data is stored in memory).

NOTE:

When selecting SUB-BRIGHTNESS mode the con sets the

CONT RAST and COLOR to minimum automatically , but

make sure that the other conditions are center, Directlyobserve the screen by eye without using a mirror.

2.4 Surround Operation CheckAd justment Procedure

Input the following audio signals to the audio input of theVIDEO INPUT terminals,

When checking surround :

(1) L CH : 400Hz sine wave 475mVrms(2) R CH : 5kHz sine wave 475mVrms

Set the L-R SPEAKER :ON.

Set the volume controls of FRONT, CENTER and REAR to

around their centers.

Set the BASS, TREBLE and BALANCE to T YP. (24-25)

No te :

Front waveform :Fount speaker output of the set .

Rear waveform :Rear speaker output of the set .

Center waveform :Center speaker output of the set .

2.4.1 Stereo Off CheckAd justment Procedure

1. Set to SURROUND: OFF and check that the waveformshown below is obtained (input signal (1) and (2)).

No te: The rear and center will have no output.

2.4.2 Stereo Off / Monaural check

Ad justment Procedure1. Check that the following waveform is obtained. The

amplitudes of 2 channels are equal (Input signal (1) only).

No te: Monaural check can be omitted. The rear and centerhave no output.

Should sink to blackShould rise slight ly from black

(400Hz)

No. 51876

AV-4300AV-5000

25

2.4.3 Stadium Surround Check

Ad justment Procedure1. Set to SURROUND : STADIUM" Check that the following waveforms are obtained (Input

signal (1) and (2))." Front : Check that the phases of R and L are different and

400Hz is superimposed on 5kHz. The amplitudes of R andL are dif ferent.

" Rear : Check that the phases of R and L are opposite and400Hz is superimposed on 5kHz. The amplitudes of R and

L are dif ferent.

Note: Center has no output.

2.4.4 Stadium Surround/Monaural CheckAd justment Procedure" Check that the following waveforms are obtained. (Input signal (1) only)" Front: R and L waveforms are almost equal." Rear: R and L waveforms are almost Zero.

No te: Center has no output.

2.4.5 Concert Surround Check

Ad justment Procedure1. Set to SURROUND: CONCERT HALL.

(Input signal (1) and (2))." Front: Check that the phases R and L signals are different

and 400 Hz is superimposed on 5kHz." Rear: Check that the R and L are opposite and 400Hz is

superimposed on 5kHz.The R and L amplitudes are equal.

No te: Amplitude levels of f ront R and L are not even

depending on P.W.B. Center has no output.

2.4.6 Concert Hall Surround / Monaural Check

Ad justment Procedure" Check that the following waveforms are obtained (Input

signal (1) only)." Front: The phases of R and L are different. The amplitudes

are different." Rear: The phases of R and L are opposite. The amplitudes

of R and L are equal.

No te: The monaural check can be omit ted. Amplitude levels of

front R and L are not even depending on the P.W.B.Center has no output.

2.4.7 Dolby Pro-logic Check

Ad justment Procedure1. Set to DOLBY PROLOGIC" Check that the following waveforms are obtained (Input

signal (1) and (2))." Front : 400Hz is superimposed on 5kHz." Rear : R and L are the same signal and 400Hz is

superimposed on 5kHz.

No te: MODE is PROLOGIC (NORMAL)

2.4.8 Dolby Pro-logic / Monaural CheckAd justment Procedure" Check that the following waveforms are obtained (Input

signal (1) only)." Front: Almost no output from both R and L." Center: Same as the audio input signal." Rear: Almost no output from R and L.

No. 51876

AV-4300AV-5000

26

2.5 Raster Inclination Adjustment (Deflection Yoke)Ad justment Preparation

1. The set can face east or west.2. Input the single NTSC cross test signal.3. Set video condit ions to factory reset.

4. The lens focus adjustment should have been completed.5. The electric focus should have been coarse adjusted.

6. The digital convergence RAM should be cleared(uncorrec ted state). With the TV set off , press and hold the

service switch located on the Power/Def lection PWB andthen press the power button.

7. Start adjustment 20 minutes or more after TV is turned ON.Ad justment Procedure

1. Apply covers to the R and B lens and projec t only greenlight.

2. Turn the G deflect ion yoke and adjust the vert ical rasterinclination.

3. Then, remove the cover of R and B lens and project red orblue light and green light together on the screen.

Note:When adjusting pay attention only at Vertical and Horizontal

line.4. Turn the deflec tion yoke of R or B and set so that the

inclination of R and B with respect to the green light is asshown below on the top and bottom sides.

5. After raster inclination adjustment, fixing screw of DY

should be screwed with 122kg-cm torque.

NOTES :

1. If internal cross-hatch does not appear af ter clearing RAMdata, press service switch again, on POWER/DEFLEC-

TION PW B.2. To res tore old RAM data, turn T V off and on.

2.6 Raster position AdjustmentAd justment Preparation

1. The set can face north.2. Input the single NTSC cross test signal.3. Set video condit ions to factory reset.

4. The lens focus adjustment should have been completed.5. The electric focus should have been coarse adjusted. The

digital convergence RAM should be c leared (uncorrectedstate). With the TV set of f, press and hold the service switch

located on the Power /Deflect ion PW B and then press thepower button.

6. Start adjustment 20 minutes or more after TV is turned ON.Ad justment Procedure

1. Turn the centering magnets for red, green and blue tosat isfy the condition below, The red and blue horizontal

lines should match with green.

l :

Screen size l1 (RED) l 2 (BLUE)

50 0 25

43 10 30

NOTES:

1. If internal cross -hatch does not appear af ter clearing RAMdata, press service switch again.

2. To res tore old RAM Data, turn TV off and on.

2.7 Vertical Size Adjustment (R630)Ad justment Preparation

1. The set can face north.2. Input the single NTSC cross test signal.

3. Set video condit ions to factory reset.4. The lens focus adjustment should have been completed.

5. The electric focus should have been coarse adjusted.6. The digital convergence RAM should be cleared

(uncorrec ted state). With the TV set off , press and hold theservice switch located on the Power/Def lection PW B and

then press the power button.7. Start adjustment 20 minutes or more after TV is turned ON.

Ad justment Procedure1. Turn only the green by applying covers to the red and blue

lens and short ing the 2 pins TS connectors on the red andblue CPT PWB.

2. Count the vert ical lines of the DCU cross-hatch .I f thenumber of vertical lines is 9, go to step (3). If the number ofvertical lines 8, push the REVEAL button and then button

number "5" on the remote control so the number of verticallines becomes "9".

3. Turn vert ical amplitude adjustment VR (R630) so that thedistance between the horizontal lines at the upside of 4th

line form center line underside of 4th line from center linethe DCU cross-hatch pattern is l.

No. 51876

AV-4300AV-5000

27

l :

Screen size V. size

50 660

43 565

NOTES :

1. If internal cross-hatch does not appear after clearing RAM data,press service switch again (on POWER / DEFLECTION PWB).

2. To res tore old RAM Data, turn TV off and on.

2.8 Horizontal Size Adjustment (R603)Ad justment Preparation

1. The set can face east or west.2. Input the single NTSC cross test signal.

3. Set video condit ions to factory reset.4. The lens focus adjustment should have been completed.

5. The electric focus should have been coarse adjusted.6. The digital convergence RAM should be cleared

(uncorrec ted state). With the TV set off, press and hold theservice switch located on the POWER/DEFLECTION PWB

and then press the power button.7. Start adjustment 20 minutes or more after TV is turned ON.Ad justment Procedure

1. Projec t only green, the same as Vertical size adjustment.2. Turn horizontal size amplitude adjustment VR (R603) and

adjust so that the distance between the vertical lines at theleft 6th line from center line of the DCU'S cross-hatch

pattern is l.

l :

Screen size H. size

50 965

43 815

NOTES :1. If internal cross-hatch does not appear af ter clearing RAM

data, press service switch again.2. To res tore old RAM data, turn TV off and on.

2.9 Beam AlignmentAd justment Preparation

1. Adjust at least 30 minutes after turning on the power switch.2. The digital convergence RAM should be cleared

(uncorrec ted state).

3. Raster inclination, centering, horizontal and verticalamplitudes and optical focus adjustment should be

completed.4. Set video condit ions to factory reset.

5. Receive cross-hatch signals. (Use of internal cross-hatchsignals allowed.)

6. Short circuit all metal parts (metal fittings, centeringmagnet) installed on the projec tion tubes to GND's of the

projec tion tubes, Since metal parts are charged withelectricity, shock may be caused if there are not short

circuited.Ad justment Procedure

1. Green (G) tube beam alignment adjustment, Short-circuit2P subminiature connector plug pins of Red (R) and Blue

(B) on the CPT boards and project only Green (G) tube.2. Put Green (G) tube beam alignment magnet to the cancel

state as shown below.3. Turn the Green (G) static focus (Focus Pack)

counterclockwise all the way and make sure of positioncross-hatch center on the screen (Halo state).

4. Turn the Green (G) static focus (Focus Pack) clockwise allthe way (Blooming state) .

5. Turn two magnets forming alignment magnet in any desireddirection and move cross-hatch center to position found in

(3).6. If image position does not shif t when Green (G) stat ic focus

(Focus pack) is turned. Green (G) beam alignment hasbeen completed.

7. If image position shif ts when Green (G) static focus (FocusPack) is turned, repeat (2) - (6).

8. Conduct beam alignment for Red (R) focus: Focus PackUFPK, Blue (B) focus: Focus Pack UFPK.

9. Upon completion of adjustment, fix beam alignments withwhite paint .

6th line from center line

4-POLE MAGNET & 2-POLE MAGNET(Neck of Projection tube)

No. 51876

AV-4300AV-5000

28

2.10 Beam Shape AdjustmentAd justment Preparation

1. The beam alignment should have been competed.2. The raster inc lination, centering, horizontal / vertical

amplitude and optical focus adjustments should have been

completed.3. Set video condit ions to factory reset.

4. Input the dot signal.Ad justment Procedure

1. Green PRT beam shape adjustment, Short -circuit 2p sub-mini connectors on Red and Blue CPT P.W.B. s to project

only the Green beam.2. Turn the green static focus fully clockwise (blooming).

3. Make the dot at the screen center a true circle us ing the 4-pole magnet as shown below.

4. Also adjust the Red and Blue PRT beam shapes accordingto the steps (1) to (3).

5. After the adjustment has been completed, return R, G andB static VRs to the Just Focus Point.

2.11 Static Focus AdjustmentAd justment Preparation

1. The raster inclination, centering, horizontal / verticalamplitude and opt ical / electrical focus beam alignment

should have been completed.2. Set video condit ions to factory reset.

3. Receive the cross-hatch pattern signal.4. Apply covers to the lenses of colors other than the color to

be adjusted and project a single color.Ad justment Procedure

1. Red (R), Green (G) and Blue (B) static focus adjus tment.Vary the static focus VR (focus pack UFPK) and make the

center of the cross-hatch pattern c learest.2. Observe the corners of the picture and check that the focus

does not conspicuously worse.

2.12 Blue Defocus AdjustmentAd justment Preparation

1. Optical and electrical focus adjustment should have beencompleted.

2. The convergence adjustment should have been completed.

3. Set Video conditions to factory resetAd justment Procedure

1. Input cross-hatch signal shown below to VIDEO or RFinput.

2. Turn the B Focus VR (Focus Pack) fully clockwise.3. After the adjustment is completed, if blue exceed the

specif ication, turn and adjust focus so that the st icking outpart of blue sat isf ies the specification.

UNEVENNESS SPECIFICATION :1cd/m2

Defocus sticking out specification

Screen size Blue sticking out

50 1.0mm

43 1.0mm

Conditions :User controls are set to the initial set positions (for shipment).

Measuring point Screen center.Cautions :" Correct the brightness gauge and amplitude of the all white

signal periodically. The aperture angle of the Brightness

gauge 1o

" Use a cross-hatch pattern to check.

PRT SURF ACE SIDE

TRUE CIRCLE SPECIFICATION

OBSERVING POINTS OF THE CORNER OF THE PICTURE

OBSERVING POINTS

STICKING OUT OF BLUE

TRUE CIRCLE DEGREE

a/b SPECIFICATION : 0.9-1.1

No. 51876

AV-4300AV-5000

29

2.13 Digital Convergence AdjustmentAd justment Preparation

1. Receive an RF or Video signal.2. Set controls to factory preset.3. Ins tall jig screen on the set.

# Require to replace 3 projection tubes4. Note the center of the video pattern displayed. This is

necessary to match dotted lines (adjustment point viewed) andactual point that is adjusted and displayed by the video signal.

5. Press the SERVICE ONLY switch (on POWER/DEFLECTIONPWB). The pattern displayed is now the digital convergence

mode.6. When performing a complete digital convergence adjustment

CLEAR DATA in RAM, See 2.5 (1) - (7).

Ad justment point (screen center)

< NTSC mode Adjustment point >

(((( : Adjustment point 913=117 point s

46.6

46.6

84.5 84.5

760.2

1015.4

54.3

54.3

108.6

33.3

84.584.5

760.2

1015.4

90.65

0.7

< NTSC mode CONVERGENCE CROSSHATCH >

(Jig screen size)

< PAL mode CONVERGENCE CROSSHATCH >(Jig screen size)

< PAL mode Adjustment point >

(((( : Adjustment point 913=117 pointsNOTE : PAL mode can be confirmed by extra horizontal lines.

No. 51876

AV-4300AV-5000

30

2.13.1 Raster Position Adjustment

Ad justment preparation1. Position adjustment

This will move an ent ire color. Use this adjustment to match

colors at the center of the screen.2. Use the buttons below to switch color to adjust.

[ ] button : Green

[ 0 ] button : Red

[ ] button : Blue


1. Press the [LST-CH] button. Extra horizontal lines appear toconfirm raster pos ition mode.

2. Use the cursor buttons to adjust position.3. Press the [LST-CH] button again to exit raster position

mode.NOTES :

1. Other functions cannot be accessed when in ras ter positionmode. Press the [LST-CH] button and confirm extra

horizontal lines disappear to exit raster position mode.2. Press the [MENU] button to switch between all colors

displayed or adjustment color and Green only.

2.13.2 Convergence Point AdjustmentAd justment preparation

1. Select color to adjust.

[ ] button : Green

[ 0 ] button : Red

[ ] button : Blue

2. Use [4], [6], [2] and [5] buttons to move the cursor posit ion(dotted lines).

3. Use cursor buttons to move the convergence.4. Adjustment points are 117 points (H:13 x V:9 points). Refer

to section 2.13.5. Start adjustment at the center of the screen.6. Cont inue adjustment at next c losest pos it ion.

7. Adjust center area first , and ending with edge section.Ad justment Procedure

1. Start adjustment at the center of the screen.2. Cont inue adjustment at next c losest pos it ion.

3. Adjust center area first , and ending with edge sections.

4. CalculationWhen convergence adjustment is f inished, press the

[CH(digit)] button on the remote control, then the calculationmode starts. The operation time is about for 5 seconds and

no picture appears during this operation. This operation fillsconvergence data between each adjustment points. If youfind misconvergence more than 1mm, adjust the

convergence again.5. Write data to ROM. Press the [INDEX] button on remote

control. First , press: "ROM W RITE?" is displayed for alarm.Second, press Data starts to write to ROM, it takes about

for 10 seconds and no picture appears during this operation.When Green dot pattern appears, writing operat ion is OK. If

writing operation is OK, press any button, to return to theadjustment mode. When red dot appears, writing operation

is NG. If writ ing operation is NG, replace digitalconvergence unit and readjust. Push the "SERVICE ONLY"

switch again to finish the adjustment.6. The digital convergence has 2 modes 60Hz (NTSC) and

50Hz (PAL), change another mode then adjust again(2.13.1 ~ 2.13.2).

< DIGITAL CONVERGENCE REMOTE CONTROL BUT TON >

NOTES :1. CH I/II button : cross-hatch/video mode

* Press [CH I/II ] button 5 times to display external signal.* Press [CH I/II ] button 5 times again to return to DCU

internal cross-hatch.2. MENU button : remove color mode

Press the [MENU] button to switch between all colors

displayed or adjustment color and green only.* Press [0] button, then press [MENU] button : Red and

Green displayed (Blue removed)

* Press [] button, then press [MENU] button : Blue and

Green displayed (Red removed)

* Press [] button, then press [MENU] button : only Green

displayed3. LST-CH button : raster position adjustment

4. / 0 / buttons : adjustment point mode

* Press [] button 5 times to 9 (H:3 x V:3) points mode.

* Press [0] button 5 t imes to 35 (H:7 x V:5) points mode.

* Press [] button 5 times to 117(H:13 x V:9) points mode.

No. 51876

AV-4300AV-5000

31

2.14 Sub Picture (P IN P) Adjustment

< Sub Picture White Balance Adjustment >(BLUE : adjustment R307(GREEN : adjustment R305

(RED : adjustment R303[On the SIGNAL P.W.B]

Ad justment Preparation1. Start adjustment about 20 minutes after the power switch is

turned ON.

2. Before adjustment for P in P sub picturemake sure that the

white balance for main picture already adjustment.

3. Display and match the sub picture details with the main picture

details.Receiving color bar s ignal

4. Condition should be set as follow.

Sub picture brightness : 3/4Sub picture Contrast : MAX

Others : CenterAd justment Procedure

1. Using the oscilloscope. Connect to P802, P832 and P862respectively for R,G,B adjustment.

2. Observe the waveform of P802 on the CPT P.W.B and turn theBLUE adjustment VR R307. Adjust so that the sub-picture

level same as the main picture level.(Refer to the waveformexplained in No.5)

3. Similar observe he waveform of P832 on the CPT.P.W.B andturn the GREEN adjustment VR R305. Adjust so that the sub-

picture level same as the main picture level.4. Similar, observe the waveform of P862 on the CPT P.W.B and

turn the RED adjustment VR R303. Adjust so that the sub-picture level same as the main picture level.

5. Ad justment specification :1V

Quality control specification : 3V

Waveform of P802, P832 and P862 : Cathode# Sub picture level compared with main picture level.

Oscilloscope range: 10V/0.2msec#### If the sub picture sag to vertical direction.

Ad just th e sub picture center point.

Main picture (white) Sub picture (white)

1V

No. 51876

AV-4300AV-5000

32

TROUBLESHOOTING1. No raster and no power

No raster

Is Power IndicatorRed LED "ON"?

DM03

Check HV-

PROTECT line

DN10,DN11

CheckDIAGNOSIS

LED's

Check

Connector

PY1, I501 etc.

Did 8 green LED'S

turn OFF same time?

D964(A12V)Check

A12V l ineI910, I001,

IY01,HM01 etc.

D940(+B)Check

+B 120V lineE994, Q777,T702, C701

etc.

D939 (TV5V)Check

TV5V lineI913, Q905D938, L911

etc.

D946 (TV9V)Check

TV9V lineI912, Q905D928, L909L922 etc.

D966 (+27V)Check

+27V lineE995, Q902IK04, IK05

etc.

D977 (22V)Check

Audio22Vline

E993,E998, I402

etc

D947 (32V)Check

Audio32Vline

E992, E997I401 etc.

D967 (-23V)Check

-23V lineE996, I909IK04, IK05

etc.

Find which LED's is going to dark of OFF.

(Other LED's are going to OFF litt le bit later same t ime.)

1. Turn OFF power SW.2. Turn ON again after several seconds, and careful observe 8 green LED's

A

B

How to check DIAGNOSIS LED's.

No

Yes

Yes

No

Is Red LED"ON"?

PROTECTION

D912

No

Yes

No. 51876

AV-4300AV-5000

33

A

Check D907, C907, Q901, R905,

R906

Check I901

IsVoltage at pin (5)of I901 10~16V?

Check I901, D911, D910, D969

Replace F901

Are volt ages of b oth

ends of T701 (prim ary

sid e) n ormal?

Check I501pin (23)-H out

pin (22)-DEF VccH.Vcc L ine

Q917, Q916Check I905, I903, I902Q914, Q913, Q912

Q909, T901 etc.

Check Q777, T701

Check I901, D907, Q701Replace F901

Has protectorF901 blown

Is basevoltage of

Q701 normal?

NO

NO

Yes

Yes

Yes

B

Does rasterappear with G and K of Q914

shorted?

Yes(About AC 0.3V)

Yes(About AC 40V)

NO

NO

NO

No. 51876

AV-4300AV-5000

34

2. No Picture

No picture

Is waveform atpin 41,42,43 ofI501 normal?

Q504, Q505, Q506,CPT PWB ASS'Y

I501, I001

Q508, I501

U101 (Front-end)

IY01

IX02 etc.(3 line comb)

Does on-screendisplay appear?

Is waveformat pin of CD-

connector normal?

Is waveformat pin of CD-

connector normal?

Normal

Abnormal

Yes

No

Normal

Normal

Abnormal

Abnormal

No. 51876

AV-4300AV-5000

35

3. Reception impossible with snow noiseMain Picture

P IN P sub-window

Reception impossible wi th snow noise

IT01, I911, I912,

I913, D104I001

Is there output ofPLL control pulse(SDA, SCL) of UT01

Is there voltageapplied to pins Vcc(9v),BP (5v),and VT(33v) of UT01

UT01

No

No

Yes

Yes

I001

I912, I913, D103U101

Is there output ofPLL control Pulse(SDA, SCL) of U101

Reception impossible wi th snow noise

Is there voltageapplied to pins Vcc(9v), BP (5v), andVT(33v) of U101

YesNo

Yes

No. 51876

AV-4300AV-5000

36

4. Defective synchronization

Defective synchronizationi

Observewaveform at

pin-32 of I501

Q902

I501I601

CheckEmitter voltage of

Q609

Abnormal (OV)

Abnormal

Normal

(26V)

Normal

No. 51876

AV-4300AV-5000

37

Are voltages at

pins 41,42 and 43

of I501 abnormal?

5. Incorrect color

Incorrect color

Color condition

Is chroma signalinput at pin 13 of I501

Are voltagesat pin-3, 4, 5 of PY1connector normal?

abnormal?

Does retrace lineappear withsignal color?

IX02, etc.(3 Line Comb.)

I501, X501

etc.

I501

Q504, Q505,

Q506

Red doesnot appear

Q861, Q862D861, PRT(R)

Green doesnot appear

Q831,Q832D831, PRT(G)

Blue doesnot appear

Q801, Q802D801, PRT(B)

No color

YesDefective

White balance

Yes

No

Yes

No

No

No. 51876

AV-4300AV-5000

38

6. No sound (when Surround off)

No Sound

Is audio signalinput at pins 3 and 5

of IS05?


of IS01?

Check voltage at pin 9 of

I401


of IS12?


of IY01?

U101

IY01Check the I

2C bus (SCL3, SDA3)

IS05(1) Check the I

2C bus (SCL, SDA)

(2) Check IG01 (GEQ IC)

E992+32V Power Supply

IS12Check the pin 7 of IS12

IS01(1) Check the Bus-Line (clock, data, enable)(2) Check IS02

Yes

0V or lower

Yes

Yes

Yes

No

No

No

No

32V

No. 51876

AV-4300AV-5000

39

No. 51876

AV-4300AV-5000

40

No. 51876

AV-4300AV-5000

41

PARTS LISTPRODUCT SAFETY NOTEComponents marked with ! have special characteristics important to safety, before replac ing any of these components, read carefully thePRODUCTS SAFETY NOTICE of this Service Manual. Dont degrade the safety of the receiver through improper servicing.

ABBREVIATIONS

Resistors Capacitors Semiconductors

PR Paper CD Ceramic disk TR TransistorTA Tantalum PF Polyester f ilm DL DiodeTM Trimmer EL Electrolyt ic ZD Zener diodeMYL Mylar CF Polypropylene VA VaristorVR Variable resistor PP Carbon f ilm TH ThermistorWW Wire wound CC Carbon composition IC ICFR Fuse resistor MF Metal oxide filmMG Metal glazed

CONTENTS

USING P. W. BOARD 41 EXPLODED VIEW PARTS LIST 42

EXPLODED VIEW 43, 44

PRINTED WIRING BOARD PARTS LIST 45 Refer to USING P. W. BOARD

PACKING / PACKING PARTS LIST [AV-4300] 67 PACKING / PACKING PARTS LIST [AV-5000] 68

USING P. W. BOARD

P.W.B ASSY NAME ASSY NUMBER PAGE

SIGNAL PWB ASS'Y 6916133A 45

T IN T PWB ASS'Y 6916161A 49

IF PWB ASS'Y [MAIN / SUB] 6916141A 49

TERMINAL PWB ASS'Y 6916201A 51

VIDEO / CHROMA PWB ASS'Y 6916201A 54

PIP PWB ASS'Y 6933121A 56

CPT PWB ASS'Y [R / G / B] 6914311A 57

VM PWB ASS'Y 6916201A 58

SURROUND PWB ASS'Y 6935011A 59

POWER / DEF. PWB ASS'Y 6941201A 61

EMC FILTER PWB ASS'Y 6941191A 66

CONTROL PWB ASS'Y 6947051A 66

DCU (DIGITAL CONVERGENCE UNIT) CS00211 ----

No. 51876

AV-4300AV-5000

42

EXPLODED VIEW PARTS LIST

! REF.NO. PART NO. DESCRIPTION !REF.NO. PART NO. DESCRIPTION

1 6031311A BACK COVER 4315 (43") 7210541A STRIP LINE 5199-036031361A BACK COVER 5020 (50") 7068281A AC CORD

2 6350212A MIRROR (43") 2997977 LINKER 1J6350231A MIRROR (50") 7210464A STRIP LINE LINKER EH-9Y

3 6231461A MIRROR SUPPORT (L) (43") 7210462A STRIP LINE LINKER EH-3Y6231471A MIRROR SUPPORT (L) (50") 2958151 LINKER CON-RE01X-X3239A901

4 6231462A MIRROR SUPPORT (R) (43") EF05941 LINKER 4P6231472A MIRROR SUPPORT (R) (50") 7210465A STRIP LINE EH-11Y

5 6231431A MIRROR SUPPORT 7210531A STRIP LINE 5199-026 6010661A SCREEN FRAME ASSY (43") 7210521A STRIP LINE TJC2-3Y-2I

6010761A SCREEN FRAME ASSY (50") 7210522A STRIP LINE TJC2-3Y-2I7 6012045A FRAME ASSY (43") 7210501A STRIP LINE TJC2-5Y-4I

6012053A FRAME ASSY (50") 7210511A STRIP LINE TJC2-4Y-4I8 6064082A BOTTOM B/C ASSY (L) EF01202 LINKER 3P9 6064071A BOTTOM B/C ASSY (C) 7210481A STRIP LINE 6J PH-PH10 6064081A BOTTOM B/C ASSY (R) 7210463A STRIP LINE EH-4Y11 6064095A BOTTON ASSY 5791012A FOCUS BOX MODULE12 6070063A SPEAKER GRILL 2776542A VM MAGNET13 6072013A DECORATIVE PANEL 2776542A VM MAGNET14 6012013A CONTROL PANEL ASSY 2776542A VM MAGNET15 6070052A PEDESTAL 7940311A JVC LOGO16 6120361A FILTER PWB HOLDER 7340141A LOGO HOLDER17 6120351A SUB PWB HOLDER 6390131A RUBBER WASHER 270X10X518 5750161A LOUDHLER 8 OHM 10W 6390133A RUBBER WASHER 105X60X1019 5750181A LOUDHLER 8 OHM 5W BY01121 DY (43")20 5750191A ALTHORN 8 OHM 10W BY00443 DY (50")21 KQ00811 CP LENS ASS'Y 3742021A CABINET WTRE CLAMPER22 KQ00811 CP LENS ASS'Y 6210712A CASTER23 KQ00811 CP LENS ASS'Y 7936261A RATING LABEL [AV-4300]

! 24 UE05611A LENS-PRT B ASS'Y (R) (43") 7936301A RATING LABEL [AV-4300/EE]! UE05671A LENS-PRT B ASS'Y (R) (50") 7936203A RATING LABEL [AV-5000]! 25 UE05612A LENS-PRT B ASS'Y (G) (43") 7936302A RATING LABEL [AV-5000/EE]! UE05672A LENS-PRT B ASS'Y (G) (50")! 26 UE05613A LENS-PRT B ASS'Y (B) (43")! UE05673A LENS-PRT B ASS'Y (B) (50")

27 6231452A PRT METAL HOLDER28 PH05101A TERMINAL HOLDER29 4491082A CHASSIS PWB BKT FB230 NA20921A CHAS.PWB BKT AP7X L131 NA03131A CHAS.PWB BKT AP5 BB132 NA03111A CHAS.PWB BKT AP5 CL133 NA03122A CHAS.PWB BKT AP7 FA234 NA03101A CHAS.PWB BKT AP5 CR135 NT00991A CHASS. FRAME AP74 R136 4524911 HEXAGON FLANGEHEAD 4*12 (X26)37 4524912 HEXAGON FLANGEHEAD 4*16 (X24)38 4518377 6*30 SCREW (X12)39 8781646A SJ2824-87-ST4*16FT SCREW (X35)40 8781650A SJ2824-87-ST4*20FT SCREW (X40)41 4159423A SJ2825-87 ST3*12FT SCREW (X18)42 MJ00111 4X14 SCREW WHITE WSH (X4)43 4137975A ST4*16 TAPPING SCREW (X4)44 6031331A 43A B/C COVER

6941191A EMC FILTER PWB ASS'Y6941201A POWER/DEF PWB ASS'Y6916133A SIGNAL PWB ASS'Y6916161A T IN T SUB ASS'Y6933121A P IN P PWB ASS'Y6914311A CPT PWB ASS'Y6935011A SURROUND PWB ASS'Y6916141A IF PWB ASS'Y6947051A CONTROL PWB ASS'Y6916201A TERMINAL/VC/VM PWB ASS'YCS00211 DCU

No. 51876

AV-4300AV-5000

43

EXPLODED VIEW (1/2)

No. 51876

AV-4300AV-5000

44

EXPLODED VIEW (2/2)

No. 51876

AV-4300AV-5000

45

PRINTED WIRING BOARD PARTS LIST

SIGNAL P.W.B ASSY (6916133A)

! SYMBOLNO. PART NO. DESCRIPTION

C001 0228010RA CD2125 10pF +-0.25pF 50VC002 0228060RA CC2125 50V-180pF-JC003 0228010RA CD2125 10pF +-0.25pF 50VC004 0228010RA CD2125 10pF +-0.25pF 50VC005 0893044RA CD 2125 10000pF +-10% 50VC006 0800056RA EL 220uF 6.3VC007 0893027RA CT2125 25V-0.1uF-KC008 0228034RA CD2125 15pF +-5% 50VC009 0228034RA CD2125 15pF +-5% 50VC010 0893044RA CD 2125 10000pF +-10% 50VC011 0800056RA EL 220uF 6.3VC014 0228042RA CD2125 33pF +-5% 50VC015 0228042RA CD2125 33pF +-5% 50VC016 0800048RA EL 100MF 10VC017 0893044RA CD 2125 10000pF +-10% 50VC018 0893044RA CD 2125 10000pF +-10% 50VC019 0800015RA EL 10uF 16VC020 0800074RA EL 470uF 16VC021 0800003RA EL 1uF 50VC022 0893031RA CD 2125 1000pF +-10% 50VC023 0228058RA CC2125 50V-150pF-JC024 0228060RA CC2125 50V-180pF-JC025 0800005RA EL 2.2uF 50VC101 0880057RA PF 0.1uF +-10% 50VC102 0880044RA PF 0.01uF +-10% 50VC103 0800049RA EL 100uF 16VC104 0800048RA EL 100MF 10VC105 0880044RA PF 0.01uF +-10% 50VC106 0880053RA PF 0.047uF +-10% 50VC107 0800049RA EL 100uF 16VC108 0800007RA EL 3.3uF 50VC109 0880044RA PF 0.01uF +-10% 50VC117 0244171RA CD 0.01uF +80%-20% 50VC118 0893023RA CT2125 25V-0.047uF-KC119 0800039RA EL 47uF 10VC120 0244171RA CD 0.01uF +80%-20% 50VC121 0880057RA PF 0.1uF +-10% 50VC122 0800047RA EL 100uF 6.3VC123 0893044RA CD 2125 10000pF +-10% 50VC301 0893044RA CD 2125 10000pF +-10% 50VC302 0800049RA EL 100uF 16VC303 0893044RA CD 2125 10000pF +-10% 50VC304 0800049RA EL 100uF 16VC305 0800049RA EL 100uF 16VC306 0893044RA CD 2125 10000pF +-10% 50VC307 0800015RA EL 10uF 16VC308 AL00791SA CT 10V-1500uF-M (LXV)C309 0880057RA PF 0.1uF +-10% 50VC313 0800015RA EL 10uF 16VC314 0800015RA EL 10uF 16VC315 0800015RA EL 10uF 16VC316 0800015RA EL 10uF 16VC317 0800015RA EL 10uF 16VC318 0800015RA EL 10uF 16VC319 0800049RA EL 100uF 16VC320 0893044RA CD 2125 10000pF +-10% 50VC321 0800015RA EL 10uF 16VC322 0800015RA EL 10uF 16VC323 0800015RA EL 10uF 16VC324 0800015RA EL 10uF 16VC325 0800015RA EL 10uF 16VC326 0800015RA EL 10uF 16VC327 0800049RA EL 100uF 16VC328 0893044RA CD 2125 10000pF +-10% 50VC329 AL00793SA CT 16V-1200uF-M (LXV)C330 0880057RA PF 0.1uF +-10% 50VC331 0880044RA PF 0.01uF +-10% 50VC401 0880057RA PF 0.1uF +-10% 50VC402 0800003RA EL 1uF 50VC403 0800003RA EL 1uF 50V


C404 0800015RA EL 10uF 16VC405 0893031RA CD 2125 1000pF +-10% 50VC406 0893031RA CD 2125 1000pF +-10% 50VC407 0800003RA EL 1uF 50VC408 0800003RA EL 1uF 50VC409 0800003RA EL 1uF 50VC410 0800042RA EL 47uF 25VC411 0800042RA EL 47uF 25VC412 0880062RA PF 0.22uF +-10% 50VC413 0253934F EL 2200uF 35VC414 0880057RA PF 0.1uF +-10% 50VC415 0800084RA CD 35V-1000uF-MC416 0800051RA EL 100uF 25VC417 0800051RA EL 100uF 25VC418 0800041RA EL 47uF 16VC419 0800083RA CD 25V-1000uF-MC420 0880044RA PF 0.01uF +-10% 50VC421 0880044RA PF 0.01uF +-10% 50VC422 0284623RA EL 1uF 50VC423 0284623RA EL 1uF 50VC424 0800015RA EL 10uF 16VC425 0800003RA EL 1uF 50VC426 0800003RA EL 1uF 50VC427 0893031RA CD 2125 1000pF +-10% 50VC428 0893031RA CD 2125 1000pF +-10% 50VC429 0800051RA EL 100uF 25VC430 0800042RA EL 47uF 25VC431 0800042RA EL 47uF 25VC432 0253934F EL 2200uF 35VC433 0880057RA PF 0.1uF +-10% 50VC434 0880057RA PF 0.1uF +-10% 50VC435 0253934F EL 2200uF 35VC436 0253934F EL 2200uF 35VC437 0880044RA PF 0.01uF +-10% 50VC438 0284625RA EL 2.2uF 50VC439 0880044RA PF 0.01uF +-10% 50VC440 0284625RA EL 2.2uF 50VC441 0880062RA PF 0.22uF +-10% 50VC442 0880057RA PF 0.1uF +-10% 50VC443 0800041RA EL 47uF 16VD404 2344041M DI 1SS254TA/1SS270TAD405 2344041M DI 1SS254TA/1SS270TAD406 2344041M DI 1SS254TA/1SS270TAD407 2344041M DI 1SS254TA/1SS270TAD408 2344041M DI 1SS254TA/1SS270TAD409 2344041M DI 1SS254TA/1SS270TAD410 2344041M DI 1SS254TA/1SS270TAD411 2344041M DI 1SS254TA/1SS270TAD412 2344041M DI 1SS254TA/1SS270TADJ01 2348212M J15BTADJ02 CH00172M SD-DFM1SD2(T)DJ03 CH00172M SD-DFM1SD2(T)DJ04 2348212M J15BTADQ01 2344041M DI 1SS254TA/1SS270TADQ02 2344041M DI 1SS254TA/1SS270TADQ03 2344041M DI 1SS254TA/1SS270TADQ04 2344041M DI 1SS254TA/1SS270TADQ05 2344041M DI 1SS254TA/1SS270TADQ06 2344041M DI 1SS254TA/1SS270TADQ07 2344041M DI 1SS254TA/1SS270TADQ08 2344041M DI 1SS254TA/1SS270TADQ11 2344041M DI 1SS254TA/1SS270TADQ12 2344041M DI 1SS254TA/1SS270TADQ13 2344041M DI 1SS254TA/1SS270TADQ14 2344041M DI 1SS254TA/1SS270TAE101 2664725 V-V CONNECTORHJ01 2791762 FILTER CAPACITOR 0.01uFHJ02 2791762 FILTER CAPACITOR 0.01uFHQ01 2791751R DSS306-55B220MHQ02 2791751R DSS306-55B220M

No. 51876

AV-4300AV-5000

46


HQ03 2791751R DSS306-55B220MHQ04 2791751R DSS306-55B220MI001 CP03868 M37270MF-168SPI002 5661343 IC AT24C16-10PC-2.7I003 2009401R IC PST529CI004 2003421 ICL-UPC7805AHFI302 2008741 IC-TEA5114AI401 2004751 TA8200AHI402 2004751 TA8200AHI403 2020021 IC TDA2822MIJ01 CK04041 MSP3410BIJ03 2000541 ICL-M51951BSLIQ01 CK04031 TPU3040IQ02 CP03211U MB814100A-70PZIQ03 2009401R IC PST529CK117 0700041MA CF 1k OHM +-5% 1/16WK190 0195248RA R3216 0 OHM 1/8WK191 0195248RA R3216 0 OHM 1/8WK192 0195248RA R3216 0 OHM 1/8WK193 0195248RA R3216 0 OHM 1/8WK194 0195248RA R3216 0 OHM 1/8WK195 0195248RA R3216 0 OHM 1/8WK196 0195248RA R3216 0 OHM 1/8WK197 0195248RA R3216 0 OHM 1/8WK428 0195248RA R3216 0 OHM 1/8WK429 0195248RA R3216 0 OHM 1/8WK430 0195248RA R3216 0 OHM 1/8WK431 0195248RA R3216 0 OHM 1/8WK432 0195248RA R3216 0 OHM 1/8WK434 0195248RA R3216 0 OHM 1/8WK435 0195248RA R3216 0 OHM 1/8WK436 0195248RA R3216 0 OHM 1/8WK437 0195248RA R3216 0 OHM 1/8WK438 0195248RA R3216 0 OHM 1/8WK439 0195248RA R3216 0 OHM 1/8WK440 0195248RA R3216 0 OHM 1/8WK441 0195248RA R3216 0 OHM 1/8WK442 0195248RA R3216 0 OHM 1/8WK443 0195248RA R3216 0 OHM 1/8WK444 0195248RA R3216 0 OHM 1/8WK445 0195248RA R3216 0 OHM 1/8WK446 0195248RA R3216 0 OHM 1/8WK447 0195248RA R3216 0 OHM 1/8WK448 0195248RA R3216 0 OHM 1/8WK449 0195248RA R3216 0 OHM 1/8WK450 0195248RA R3216 0 OHM 1/8WK451 0195248RA R3216 0 OHM 1/8WK452 0195248RA R3216 0 OHM 1/8WK501 0195248RA R3216 0 OHM 1/8WK511 0195248RA R3216 0 OHM 1/8WK513 0195248RA R3216 0 OHM 1/8WK514 0195248RA R3216 0 OHM 1/8WK515 0195248RA R3216 0 OHM 1/8WK517 0195248RA R3216 0 OHM 1/8WK537 0195248RA R3216 0 OHM 1/8WK539 0195248RA R3216 0 OHM 1/8WK548 0195248RA R3216 0 OHM 1/8WK561 0195248RA R3216 0 OHM 1/8WK572 0195248RA R3216 0 OHM 1/8WK659 0195248RA R3216 0 OHM 1/8WK660 0195248RA R3216 0 OHM 1/8WK662 0195250RA R2125 0 OHM 1/16WK665 0195250RA R2125 0 OHM 1/16WK666 0195250RA R2125 0 OHM 1/16WKS01 0195250RA R2125 0 OHM 1/16WKS02 0195250RA R2125 0 OHM 1/16WKS03 0195250RA R2125 0 OHM 1/16WKS04 0195250RA R2125 0 OHM 1/16WL001 2123781R COIL 100uHL002 2123781R COIL 100uHL003 2122934M 2.2uH-ML101 2123781R COIL 100uHL102 2123781R COIL 100uHL105 2123781R COIL 100uHL108 2123781R COIL 100uH


L109 2123781R COIL 100uHL302 2123781R COIL 100uHL303 2123781R COIL 100uHL304 BH00214RA 100uH-KL401 2123462MA FERRITE BEADS 2.3uHL402 2123462MA FERRITE BEADS 2.3uHL403 2123462MA FERRITE BEADS 2.3uHLJ01 2123781R COIL 100uHLJ02 2123781R COIL 100uHLJ03 2123781R COIL 100uHLJ04 BJ00021 FL-8R0H6R0SQLQ01 2123781R COIL 100uHLQ02 2123781R COIL 100uHLQ03 2123781R COIL 100uHPCB ED00572 15P SOCKETPCC ED00576 20P SOCKETPCD ED00576 20P SOCKETPCL 2903543 3P BASE WITH PLUGPCR 2903543 3P BASE WITH PLUGPCX2 7244111A 2P SOCKETPFJ 7244118A 9P SOCKETPFN 7244112A 3P SOCKETPISA 7240031A 12P CONNECTORPISB 7240028A 10P CONNECTORPL 2903545 5P BASE WITH PLUGPR 2903544 4P BASE WITH PLUGPS 7244111A 2P SOCKETPSD1 ED01471U 7P CONNECTORPSD2 ED01472U 11P CONNECTORPSD3 ED01472U 11P CONNECTORPSD4 ED01473U 13P CONNECTORPSD5 ED01471U 7P CONNECTORPSI1 ED00575 18P SOCKETPSI2 ED00575 18P SOCKETPSU1 ED00576 20P SOCKETPSU2 ED00576 20P SOCKETPTIT 7244122A 12P SOCKETPTP 7244113A 4P SOCKETPVM1 ED00566 10P SOCKETPVM2 ED00566 10P SOCKETQ001 2325691R TR 2SC2412k(BQ)Q002 2325691R TR 2SC2412k(BQ)Q003 2325691R TR 2SC2412k(BQ)Q004 2325691R TR 2SC2412k(BQ)Q005 2325691R TR 2SC2412k(BQ)Q006 2325691R TR 2SC2412k(BQ)Q007 2325691R TR 2SC2412k(BQ)Q008 2325691R TR 2SC2412k(BQ)Q009 2325691R TR 2SC2412k(BQ)Q010 2325691R TR 2SC2412k(BQ)Q011 2325691R TR 2SC2412k(BQ)Q012 2325691R TR 2SC2412k(BQ)Q013 2325781R TR 2SA1037K T146Q/RQ014 2325691R TR 2SC2412k(BQ)Q015 2325691R TR 2SC2412k(BQ)Q016 2325691R TR 2SC2412k(BQ)Q301 2325691R TR 2SC2412k(BQ)Q303 2325691R TR 2SC2412k(BQ)Q304 2325691R TR 2SC2412k(BQ)Q305 2325691R TR 2SC2412k(BQ)Q401 2325691R TR 2SC2412k(BQ)Q402 2325691R TR 2SC2412k(BQ)Q403 2325691R TR 2SC2412k(BQ)Q404 2325691R TR 2SC2412k(BQ)Q405 2325691R TR 2SC2412k(BQ)Q406 2325691R TR 2SC2412k(BQ)Q407 2325691R TR 2SC2412k(BQ)QQ01 2325691R TR 2SC2412k(BQ)QQ02 2325691R TR 2SC2412k(BQ)QQ03 2327753R TR 2SA1390 C/DR001 0700041MA CF 1k OHM +-5% 1/16WR002 0195900RA R2125 1k OHM +-5% 1/10WR003 0195914RA R2125 3.9k OHM +-5% 1/16WR004 0700041MA CF 1k OHM +-5% 1/16WR005 0195900RA R2125 1k OHM +-5% 1/10W

No. 51876

AV-4300AV-5000

47


R006 0195904RA R2125 1.5k OHM +-5% 1/16WR007 0195914RA R2125 3.9k OHM +-5% 1/16WR008 0700041MA CF 1k OHM +-5% 1/16WR009 0195900RA R2125 1k OHM +-5% 1/10WR010 0195914RA R2125 3.9k OHM +-5% 1/16WR011 0700041MA CF 1k OHM +-5% 1/16WR012 0195925RA R2125 10k OHM +-5% 1/16WR013 0195900RA R2125 1k OHM +-5% 1/10WR014 0700041MA CF 1k OHM +-5% 1/16WR015 0195941RA R2125 47k OHM +-5% 1/16WR016 0195904RA R2125 1.5k OHM +-5% 1/16WR017 0195941RA R2125 47k OHM +-5% 1/16WR018 0700041MA CF 1k OHM +-5% 1/16WR019 0195900RA R2125 1k OHM +-5% 1/10WR021 0195916RA R2125 4.7k OHM +-5% 1/16R022 0195925RA R2125 10k OHM +-5% 1/16WR024 0195925RA R2125 10k OHM +-5% 1/16WR025 0195925RA R2125 10k OHM +-5% 1/16WR026 0195925RA R2125 10k OHM +-5% 1/16WR027 0195875RA R2125 100 OHM +-5% 1/10WR028 0195875RA R2125 100 OHM +-5% 1/10WR029 0195875RA R2125 100 OHM +-5% 1/10WR031 0195875RA R2125 100 OHM +-5% 1/10WR032 0195875RA R2125 100 OHM +-5% 1/10WR034 0195875RA R2125 100 OHM +-5% 1/10WR035 0195875RA R2125 100 OHM +-5% 1/10WR036 0195875RA R2125 100 OHM +-5% 1/10WR037 0195900RA R2125 1k OHM +-5% 1/10WR038 0195925RA R2125 10k OHM +-5% 1/16WR040 0700041MA CF 1k OHM +-5% 1/16WR041 0195925RA R2125 10k OHM +-5% 1/16WR042 0195916RA R2125 4.7k OHM +-5% 1/16R043 0195925RA R2125 10k OHM +-5% 1/16WR044 0195925RA R2125 10k OHM +-5% 1/16WR045 0195916RA R2125 4.7k OHM +-5% 1/16R046 0195900RA R2125 1k OHM +-5% 1/10WR047 0195875RA R2125 100 OHM +-5% 1/10WR048 0195875RA R2125 100 OHM +-5% 1/10WR049 0195925RA R2125 10k OHM +-5% 1/16WR050 0195916RA R2125 4.7k OHM +-5% 1/16R051 0195916RA R2125 4.7k OHM +-5% 1/16R054 0195916RA R2125 4.7k OHM +-5% 1/16R055 0195875RA R2125 100 OHM +-5% 1/10WR056 0195925RA R2125 10k OHM +-5% 1/16WR057 0195900RA R2125 1k OHM +-5% 1/10WR058 0195925RA R2125 10k OHM +-5% 1/16WR059 0195875RA R2125 100 OHM +-5% 1/10WR060 0195925RA R2125 10k OHM +-5% 1/16WR061 0195900RA R2125 1k OHM +-5% 1/10WR062 0195925RA R2125 10k OHM +-5% 1/16WR063 0195900RA R2125 1k OHM +-5% 1/10WR064 0195916RA R2125 4.7k OHM +-5% 1/16R065 0195875RA R2125 100 OHM +-5% 1/10WR066 0195925RA R2125 10k OHM +-5% 1/16WR067 0195900RA R2125 1k OHM +-5% 1/10WR068 0195875RA R2125 100 OHM +-5% 1/10WR069 0195916RA R2125 4.7k OHM +-5% 1/16R070 0195900RA R2125 1k OHM +-5% 1/10WR072 0195875RA R2125 100 OHM +-5% 1/10WR074 0195875RA R2125 100 OHM +-5% 1/10WR075 0195900RA R2125 1k OHM +-5% 1/10WR076 0195900RA R2125 1k OHM +-5% 1/10WR077 0195875RA R2125 100 OHM +-5% 1/10WR078 0195912RA R2125 3.3k OHM +-5% 1/16WR079 0195900RA R2125 1k OHM +-5% 1/10WR080 0195900RA R2125 1k OHM +-5% 1/10WR081 0700045MA CF 2.2k OHM +-5% 1/16WR082 0195875RA R2125 100 OHM +-5% 1/10WR083 0195941RA R2125 47k OHM +-5% 1/16WR084 0195918RA R2125 5.6k OHM +-5% 1/16WR085 0195950RA R2125 100k OHM +-5% 1/16WR086 0195947RA R2125 10k OHM +-5% 1/16WR087 0195925RA R2125 10k OHM +-5% 1/16WR088 0195918RA R2125 5.6k OHM +-5% 1/16WR089 0195918RA R2125 5.6k OHM +-5% 1/16W


R091 0195918RA R2125 5.6k OHM +-5% 1/16WR092 0195927RA R2125 12k OHM +-5% 1/16WR093 0195941RA R2125 47k OHM +-5% 1/16WR095 0195900RA R2125 1k OHM +-5% 1/10WR096 0195941RA R2125 47k OHM +-5% 1/16WR097 0195916RA R2125 4.7k OHM +-5% 1/16R098 0195933RA R2125 22 k OHM +-5% 1/16WR099 0195927RA R2125 12k OHM +-5% 1/16WR0A0 0195927RA R2125 12k OHM +-5% 1/16WR0A1 0195925RA R2125 10k OHM +-5% 1/16WR0A2 0195900RA R2125 1k OHM +-5% 1/10WR0A3 0195900RA R2125 1k OHM +-5% 1/10WR0A6 0700037MA CF 560 OHM +-5% 1/16WR0A7 0195931RA R2125 18k OHM +-5% 1/16WR0A8 0195933RA R2125 22 k OHM +-5% 1/16WR0B0 0195925RA R2125 10k OHM +-5% 1/16WR0B1 0195875RA R2125 100 OHM +-5% 1/10WR0B2 0195925RA R2125 10k OHM +-5% 1/16WR0B3 0195875RA R2125 100 OHM +-5% 1/10WR0B4 0195925RA R2125 10k OHM +-5% 1/16WR0B5 0195900RA R2125 1k OHM +-5% 1/10WR0B6 0195875RA R2125 100 OHM +-5% 1/10WR0B7 0195925RA R2125 10k OHM +-5% 1/16WR0B8 0195908RA R2125 2.2k OHM +-5% 1/16WR0B9 0195933RA R2125 22 k OHM +-5% 1/16WR0C0 0195900RA R2125 1k OHM +-5% 1/10WR0C1 0195900RA R2125 1k OHM +-5% 1/10WR0C2 0195900RA R2125 1k OHM +-5% 1/10WR0C3 0195883RA R2125 220 OHM +-5% 1/10WR0C4 0195883RA R2125 220 OHM +-5% 1/10WR0C5 0195900RA R2125 1k OHM +-5% 1/10WR0C7 0195875RA R2125 100 OHM +-5% 1/10WR0C8 0195875RA R2125 100 OHM +-5% 1/10WR0C9 0195883RA R2125 220 OHM +-5% 1/10WR0D0 0195950RA R2125 100k OHM +-5% 1/16WR0D1 0195947RA R2125 83k OHM +-5% 1/16WR102 0195875RA R2125 100 OHM +-5% 1/10WR103 0195875RA R2125 100 OHM +-5% 1/10WR104 0114171MA CF 2.7k OHM +-5% 1/4WR106 0114171MA CF 2.7k OHM +-5% 1/4WR301 0195875RA R2125 100 OHM +-5% 1/10WR302 0195875RA R2125 100 OHM +-5% 1/10WR303 0150110A VR 500 OHM-B RS-6R304 0700027MA CF 100 OHM +-5% 1/16WR305 0150110A VR 500 OHM-B RS-6R306 0700027MA CF 100 OHM +-5% 1/16WR307 0150110A VR 500 OHM-B RS-6R308 0700027MA CF 100 OHM +-5% 1/16WR309 0700041MA CF 1k OHM +-5% 1/16WR310 0700041MA CF 1k OHM +-5% 1/16WR311 0700041MA CF 1k OHM +-5% 1/16WR312 0700041MA CF 1k OHM +-5% 1/16WR313 0195900RA R2125 1k OHM +-5% 1/10WR314 0700041MA CF 1k OHM +-5% 1/16WR315 0195900RA R2125 1k OHM +-5% 1/10WR316 0195875RA R2125 100 OHM +-5% 1/10WR317 0195900RA R2125 1k OHM +-5% 1/10WR318 0195875RA R2125 100 OHM +-5% 1/10WR319 0195900RA R2125 1k OHM +-5% 1/10WR320 0195875RA R2125 100 OHM +-5% 1/10WR321 0195900RA R2125 1k OHM +-5% 1/10WR322 0195875RA R2125 100 OHM +-5% 1/10WR323 0195875RA R2125 100 OHM +-5% 1/10WR324 0195875RA R2125 100 OHM +-5% 1/10WR325 0195875RA R2125 100 OHM +-5% 1/10WR326 0195875RA R2125 100 OHM +-5% 1/10WR327 0195875RA R2125 100 OHM +-5% 1/10WR328 0195875RA R2125 100 OHM +-5% 1/10WR329 0195875RA R2125 100 OHM +-5% 1/10WR331 0195875RA R2125 100 OHM +-5% 1/10WR333 0700027MA CF 100 OHM +-5% 1/16WR334 0195900RA R2125 1k OHM +-5% 1/10WR335 0195925RA R2125 10k OHM +-5% 1/16WR336 0195250RA R2125 0 OHM 1/16WR368 0195925RA R2125 10k OHM +-5% 1/16W

No. 51876

AV-4300AV-5000

48


R369 0195883RA R2125 220 OHM +-5% 1/10WR370 0195883RA R2125 220 OHM +-5% 1/10WR371 0195883RA R2125 220 OHM +-5% 1/10WR372 0195941RA R2125 47k OHM +-5% 1/16WR373 0195925RA R2125 10k OHM +-5% 1/16WR374 0195918RA R2125 5.6k OHM +-5% 1/16WR375 0195925RA R2125 10k OHM +-5% 1/16WR376 0195947RA R2125 5.6k OHM +-5% 1/16WR377 0195918RA R2125 5.6k OHM +-5% 1/16WR378 0195897RA R2125 820 OHM +-5% 1/10WR379 0195897RA R2125 820 OHM +-5% 1/10WR380 0195897RA R2125 820 OHM +-5% 1/10WR381 0195891RA R2125 470 OHM +-5% 1/10WR382 0195891RA R2125 470 OHM +-5% 1/10WR383 0195891RA R2125 470 OHM +-5% 1/10WR384 0195879RA R2125 150 OHM +-5% 1/10WR385 0195879RA R2125 150 OHM +-5% 1/10WR386 0195879RA R2125 150 OHM +-5% 1/10WR387 0195870RA R2125 68 OHM +-5% 1/10WR388 0195870RA R2125 68 OHM +-5% 1/10WR389 0195870RA R2125 68 OHM +-5% 1/10WR401 0700063MA CF 47k OHM +-5% 1/16WR402 0700067MA CF 100k OHM +-5% 1/16WR403 0700063MA CF 47k OHM +-5% 1/16WR404 0700049MA CF 4.7k OHM +-5% 1/16WR405 0700045MA CF 2.2k OHM +-5% 1/16WR406 0700054MA CF 10k OHM +-5% 1/16WR407 0700036MA CF 470 OHM +-5% 1/16WR408 0700041MA CF 1k OHM +-5% 1/16WR409 0195933RA R2125 22 k OHM +-5% 1/16WR410 0700065MA CF 68k OHM +-5% 1/16WR411 0700065MA CF 68k OHM +-5% 1/16WR412 0114161MA CF 1k OHM +-5% 1/4WR413 0700045MA CF 2.2k OHM +-5% 1/16WR414 0700045MA CF 2.2k OHM +-5% 1/16WR415 0700065MA CF 68k OHM +-5% 1/16WR416 0700054MA CF 10k OHM +-5% 1/16WR417 0700054MA CF 10k OHM +-5% 1/16WR418 0700049MA CF 4.7k OHM +-5% 1/16WR419 0700049MA CF 4.7k OHM +-5% 1/16WR420 0700063MA CF 47k OHM +-5% 1/16WR421 0700067MA CF 100k OHM +-5% 1/16WR422 0700063MA CF 47k OHM +-5% 1/16WR423 0700036MA CF 470 OHM +-5% 1/16WR424 0700041MA CF 1k OHM +-5% 1/16WR425 0700058MA CF 22k OHM +-5% 1/16WR426 0700065MA CF 68k OHM +-5% 1/16WR427 0700065MA CF 68k OHM +-5% 1/16WR428 0114161MA CF 1k OHM +-5% 1/4WR429 0119505A FR 2.2 OHM +-5% 1/4WR430 0119505A FR 2.2 OHM +-5% 1/4WR431 0114161MA CF 1k OHM +-5% 1/4WR432 0119505A FR 2.2 OHM +-5% 1/4WR433 0119505A FR 2.2 OHM +-5% 1/4WR434 0114161MA CF 1k OHM +-5% 1/4WR435 0113725MA CF 100 OHM +-5% 1/2WR436 0114133MA CF 120 OHM +-5% 1/4WR437 0114133MA CF 120 OHM +-5% 1/4WR438 0195922RA R2125 8.2k OHM +-5% 1/16WR439 0195922RA R2125 8.2k OHM +-5% 1/16WR440 0195910RA R2125 2.7k OHM +-5% 1/16WR441 0195910RA R2125 2.7k OHM +-5% 1/16WR442 0195950RA R2125 100k OHM +-5% 1/16WR443 0195950RA R2125 100k OHM +-5% 1/16WR444 0195250RA R2125 0 OHM 1/16WR445 0195250RA R2125 0 OHM 1/16WR446 0195862RA R2125 33 OHM +-5% 1/10WR447 0195862RA R2125 33 OHM +-5% 1/10WRJ01 0195875RA R2125 100 OHM +-5% 1/10WRJ02 0195875RA R2125 100 OHM +-5% 1/10WRJ03 0195900RA R2125 1k OHM +-5% 1/10WRJ04 0195891RA R2125 470 OHM +-5% 1/10WRJ05 0195891RA R2125 470 OHM +-5% 1/10WRJ06 0195925RA R2125 10k OHM +-5% 1/16WRJ07 0195900RA R2125 1k OHM +-5% 1/10W


RQ01 0195875RA R2125 100 OHM +-5% 1/10WRQ02 0195875RA R2125 100 OHM +-5% 1/10WRQ03 0195875RA R2125 100 OHM +-5% 1/10WRQ04 0195875RA R2125 100 OHM +-5% 1/10WRQ05 0195875RA R2125 100 OHM +-5% 1/10WRQ06 0195875RA R2125 100 OHM +-5% 1/10WRQ07 0195875RA R2125 100 OHM +-5% 1/10WRQ08 0195925RA R2125 10k OHM +-5% 1/16WRQ09 0195875RA R2125 100 OHM +-5% 1/10WRQ10 0195875RA R2125 100 OHM +-5% 1/10WRQ11 0195875RA R2125 100 OHM +-5% 1/10WRQ12 0195875RA R2125 100 OHM +-5% 1/10WRQ13 0195900RA R2125 1k OHM +-5% 1/10WRQ14 0195900RA R2125 1k OHM +-5% 1/10WRQ15 0195900RA R2125 1k OHM +-5% 1/10WRQ16 0195900RA R2125 1k OHM +-5% 1/10WRQ17 0195916RA R2125 4.7k OHM +-5% 1/16RQ18 0195916RA R2125 4.7k OHM +-5% 1/16RQ19 0195916RA R2125 4.7k OHM +-5% 1/16RQ20 0195891RA R2125 470 OHM +-5% 1/10WRQ22 0195875RA R2125 100 OHM +-5% 1/10WRQ23 0195933RA R2125 22 k OHM +-5% 1/16WRQ24 0195933RA R2125 22 k OHM +-5% 1/16WRQ25 0195941RA R2125 47k OHM +-5% 1/16WRQ26 0195925RA R2125 10k OHM +-5% 1/16WRQ27 0195900RA R2125 1k OHM +-5% 1/10WRQ28 0195900RA R2125 1k OHM +-5% 1/10WRQ302 0195250RA R2125 0 OHM 1/16WRQ32 0114131MA CF 100 OHM +-5% 1/4WRQ33 0114131MA CF 100 OHM +-5% 1/4WRQ34 0114181MA CF 6.8k OHM +-5% 1/4WRQ35 0195950RA R2125 100k OHM +-5% 1/16WRQ36 0114161MA CF 1k OHM +-5% 1/4WU101 HJ00132 TUT BTP-AH453U102 FU00401A MEX ANT SPLITTERX001 2163974 VFL-CSA8.00MTXJ01 BP00441 OSX 18MHZKD309 1-65 JUMPERKD310 1-65 JUMPERKD311 1-65 JUMPERKD413 1-65 JUMPERNIQ01A ED01881 44 PIN PLCC SOCKETBJ01 JK04162A PWB AP7M SIGNAL PWB

No. 51876

AV-4300AV-5000

49

T IN T P.W.B ASSY (6916161A)


CT01 0244171RA CK45F1H103ZBCT02 0800048RA CEL-101M100WMLTCT03 0244171RA CK45F1H103ZBCT04 0800049RA CE04W1C101MBCT05 0244171RA CK45F1H103ZBCT06 0244171RA CK45F1H103ZBCT07 0244171RA CK45F1H103ZBCT08 0800049RA CE04W1C101MBCT09 0800015RA CE04W1C100MBCT10 0244171RA CK45F1H103ZBCT11 0244171RA CK45F1H103ZBCT12 0244171RA CK45F1H103ZBCT13 0800041RA CE04W1C470MBDT01 2344041M 1SS254TA/1SS270TADT02 2344041M 1SS254TA/1SS270TADT03 2344041M 1SS254TA/1SS270TADT04 2344041M 1SS254TA/1SS270TADT05 2339867M HZS9C1DT06 2339867M HZS9C1DT07 2339867M HZS9C1DT08 2339867M HZS9C1DT09 2344041M 1SS254TA/1SS270TADT10 2344041M 1SS254TA/1SS270TADT11 2344041M 1SS254TA/1SS270TADT12 2344041M 1SS254TA/1SS270TAIT01 2003423 ICL-UPC7893AHFLT01 2123781R EL 101KBLT02 2123781R EL 101KBLT03 2123781R EL 101KBLT04 2123781R EL 101KBRT01 0114131MA RD14S2E101JBRT02 0114131MA RD14S2E101JBRT03 0114201MA RD14S2E103JBRT04 0114131MA RD14S2E101JBRT05 0114131MA RD14S2E101JBRT06 0114131MA RD14S2E101JBRT07 0114131MA RD14S2E101JBUT01 HJ00132 TUT BTP-AH453BT01 JK04151A PWB AP7M T IN T SUB

IF P.W.B ASSY (6916141A)


C201 0800003RA EL 1uF 50VC202 0893044RA CD 2125 10000pF +-10% 50VC203 0893023RA CD 2125 0.048uF +-10% 25VC204 0800023RA EL 22uF 16VC205 0893044RA CD 2125 10000pF +-10% 50VC206 0893044RA CD 2125 10000pF +-10% 50VC207 0893039RA CD 2125 4700pF +-10% 50VC208 0893053RA CD 2125 0.0470pF +-10% 50VC209 0893044RA CD 2125 10000pF +-10% 50VC210 0893044RA CD 2125 10000pF +-10% 50VC211 0800048RA EL 100MF 10VC212 0800001RA EL 0.47uF 50VC213 0800005RA EL 2.2uF 50VC214 0228037RA CD 2125 20pF +-10% 50VC216 0893044RA CD 2125 10000pF +-10% 50VC217 0893044RA CD 2125 10000pF +-10% 50VC218 0893044RA CD 2125 10000pF +-10% 50VC219 0893044RA CD 2125 10000pF +-10% 50VC220 0893044RA CD 2125 10000pF +-10% 50VC221 0893044RA CD 2125 10000pF +-10% 50VC222 0893044RA CD 2125 10000pF +-10% 50VC224 0800023RA EL 22uF 16VC226 0800005RA EL 2.2uF 50VC227 0880062RA PF 0.22uF +-10% 50VC228 0880057RA PF 0.1uF +-10% 50VC229 0893044RA CD 2125 10000pF +-10% 50VC230 0893044RA CD 2125 10000pF +-10% 50VC231 0893084RA CD 2125 0.047uF +-10% 50VC232 0800049RA EL 100uF 16VC233 0893044RA CD 2125 10000pF +-10% 50VC234 0228008RA CD2125 8pF +-0.25pF 50VC235 0800072RA EL 470uF 6.3VC236 0800015RA EL 10uF 16VC237 0893044RA CD 2125 10000pF +-10% 50VD201 2344041M DI 1SS254TA/1SS270TAD202 2344041M DI 1SS254TA/1SS270TAD203 2344041M DI 1SS254TA/1SS270TAD204 2344041M DI 1SS254TA/1SS270TAD205 2344041M DI 1SS254TA/1SS270TAD206 2344041M DI 1SS254TA/1SS270TAD207 2344041M DI 1SS254TA/1SS270TAI201 CP02021U IC TDA9815(IF)I203 2004693 IC MM1113XSK209 0195250RA R2125 0 OHM 1/16WK210 0195250RA R2125 0 OHM 1/16WK216 0195250RA R2125 0 OHM 1/16WK251 0195248RA R3216 0 OHM 1/8WK252 0227209RA CD 3216 0.01uFHM 1/8WK253 0195248RA R3216 0 OHM 1/8WK254 0195248RA R3216 0 OHM 1/8WK256 0195248RA R3216 0 OHM 1/8WK257 0195250RA R2125 0 OHM 1/16WK260 0195250RA R2125 0 OHM 1/16WK261 0195250RA R2125 0 OHM 1/16WK263 0195250RA R2125 0 OHM 1/16WK267 0195248RA R3216 0 OHM 1/8WK269 0195248RA R3216 0 OHM 1/8WK270 0195248RA R3216 0 OHM 1/8WK271 0195248RA R3216 0 OHM 1/8WK272 0195250RA R2125 0 OHM 1/16WK273 0195250RA R2125 0 OHM 1/16WK274 0195250RA R2125 0 OHM 1/16WK276 0195248RA R3216 0 OHM 1/8WK277 0195248RA R3216 0 OHM 1/8WK278 0195248RA R3216 0 OHM 1/8WK279 0195250RA R2125 0 OHM 1/16WK280 0195250RA R2125 0 OHM 1/16WK281 0195250RA R2125 0 OHM 1/16WK282 0195250RA R2125 0 OHM 1/16WK283 0195248RA R3216 0 OHM 1/8WK284 0195250RA R2125 0 OHM 1/16WK285 0195250RA R2125 0 OHM 1/16WK286 0195250RA R2125 0 OHM 1/16W

No. 51876

AV-4300AV-5000

50


K287 0195250RA R2125 0 OHM 1/16WK288 0195250RA R2125 0 OHM 1/16WK290 0195250RA R2125 0 OHM 1/16WK291 0195250RA R2125 0 OHM 1/16WK292 0195248RA R3216 0 OHM 1/8WK295 0195248RA R3216 0 OHM 1/8WK296 0195250RA R2125 0 OHM 1/16WK298 0195250RA R2125 0 OHM 1/16WK299 0195248RA R3216 0 OHM 1/8WK300 0195248RA R3216 0 OHM 1/8WK301 0195250RA R2125 0 OHM 1/16WK303 0195248RA R3216 0 OHM 1/8WK304 0195250RA R2125 0 OHM 1/16WK305 0195248RA R3216 0 OHM 1/8WK306 0195248RA R3216 0 OHM 1/8WK307 0195250RA R2125 0 OHM 1/16WK308 0195248RA R3216 0 OHM 1/8WK312 0195248RA R3216 0 OHM 1/8WK313 0195250RA R2125 0 OHM 1/16WK316 0195248RA R3216 0 OHM 1/8WK317 0195250RA R2125 0 OHM 1/16WK319 0195250RA R2125 0 OHM 1/16WL201 2122937MA LAL AXIAL COIL 3.9uHL202 BH01041 VCO COIL HC----JS1L205 2122253MA LA AXIAL COIL 100uHL206 2122944MA LAL AXIAL COIL 12uHL207 2122943MA LAL AXIAL COIL 10uHL208 2122939MA LAL AXIAL COIL 5.6uHL209 2122956MA LAL AXIAL COIL 100uHL210 2122956MA LAL AXIAL COIL 100uHQ201 2328161R TR 2SC4265JC02TRQ202 2325691R TR 2SC2412k(BQ)Q203 2325781R TR 2SA1037K T146Q/RQ204 2325691R TR 2SC2412k(BQ)Q205 2325691R TR 2SC2412k(BQ)Q206 2325691R TR 2SC2412k(BQ)Q207 2325691R TR 2SC2412k(BQ)Q208 2325781R TR 2SA1037K T146Q/RQ209 2328161R TR 2SC4265JC02TRQ210 2325691R TR 2SC2412k(BQ)Q211 2325691R TR 2SC2412k(BQ)Q212 2325691R TR 2SC2412k(BQ)Q213 2325691R TR 2SC2412k(BQ)Q214 2325691R TR 2SC2412k(BQ)Q215 2325781R TR 2SA1037K T146Q/RQ216 2325691R TR 2SC2412k(BQ)Q218 2325691R TR 2SC2412k(BQ)Q220 2325691R TR 2SC2412k(BQ)Q223 2325691R TR 2SC2412k(BQ)R201 0195862RA R2125 33 OHM +-5% 1/10WR202 0195850RA R2125 10 OHM +-5% 1/10WR203 0195875RA R2125 100 OHM +-5% 1/10WR204 0195908RA R2125 2.2k OHM +-5% 1/16WR205 0195877RA R2125 120 OHM +-5% 1/10WR206 0195883RA R2125 220 OHM +-5% 1/10WR207 0195922RA R2125 8.2k OHM +-5% 1/16WR208 0195933RA R2125 22 k OHM +-5% 1/16WR209 0195908RA R2125 2.2k OHM +-5% 1/16WR210 0195910RA R2125 2.7k OHM +-5% 1/16WR211 0195910RA R2125 2.7k OHM +-5% 1/16WR212 0195941RA R2125 47k OHM +-5% 1/16WR213 0195933RA R2125 22 k OHM +-5% 1/16WR214 0195933RA R2125 22 k OHM +-5% 1/16WR215 0195941RA R2125 47k OHM +-5% 1/16WR216 0195933RA R2125 22 k OHM +-5% 1/16WR217 0195943RA R2125 56k OHM +-5% 1/16WR218 0195943RA R2125 56k OHM +-5% 1/16WR219 0195900RA R2125 1k OHM +-5% 1/10WR220 0195881RA R2125 180 OHM +-5% 1/10WR221 0195943RA R2125 56k OHM +-5% 1/16WR222 0195931RA R2125 18k OHM +-5% 1/16WR223 0195910RA R2125 2.7k OHM +-5% 1/16WR224 0195887RA R2125 330 OHM +-5% 1/10WR225 0195908RA R2125 2.2k OHM +-5% 1/16WR226 0195943RA R2125 56k OHM +-5% 1/16W


R227 0195933RA R2125 22 k OHM +-5% 1/16WR228 0195875RA R2125 100 OHM +-5% 1/10WR229 0195887RA R2125 330 OHM +-5% 1/10WR230 0195887RA R2125 330 OHM +-5% 1/10WR231 0195910RA R2125 2.7k OHM +-5% 1/16WR232 0195910RA R2125 2.7k OHM +-5% 1/16WR233 0195910RA R2125 2.7k OHM +-5% 1/16WR234 0195933RA R2125 22 k OHM +-5% 1/16WR235 0195933RA R2125 22 k OHM +-5% 1/16WR236 0195887RA R2125 330 OHM +-5% 1/10WR237 0195908RA R2125 2.2k OHM +-5% 1/16WR238 0195908RA R2125 2.2k OHM +-5% 1/16WR239 0195908RA R2125 2.2k OHM +-5% 1/16WR241 0195933RA R2125 22 k OHM +-5% 1/16WR242 0195950RA R2125 100k OHM +-5% 1/16WB201 JK04201A PWB AP7M IF PWBR243 0195925RA R2125 10k OHM +-5% 1/16WR244 0195950RA R2125 100k OHM +-5% 1/16WR245 0150305A VR 10K OHM-B RV-06R246 0195875RA R2125 100 OHM +-5% 1/10WR247 0195925RA R2125 10k OHM +-5% 1/16WR249 0195900RA R2125 1k OHM +-5% 1/10WR251 0195250RA R2125 0 OHM 1/16WR253 0195920RA R2125 6.8k OHM +-5% 1/16WR255 0195920RA R2125 6.8k OHM +-5% 1/16WR256 0195879RA RES 2125 CHIP 1/10W 150-JR257 0195884RA RES 2125 CHIP 1/10W 240-JR258 0195885RA R2125 270 OHM +-5% 1/10WR259 0114153MA CF 820 OHM +-5% 1/4WR260 0195875RA R2125 100 OHM +-5% 1/10WR261 0195900RA R2125 1k OHM +-5% 1/10WR262 0195900RA R2125 1k OHM +-5% 1/10WR263 0195933RA R2125 22 k OHM +-5% 1/16WR265 0195891RA R2125 470 OHM +-5% 1/10WR267 0195933RA R2125 22 k OHM +-5% 1/16WR268 0195900RA R2125 1k OHM +-5% 1/10WR269 0195250RA R2125 0 OHM 1/16WR271 0195900RA R2125 1k OHM +-5% 1/10WR272 0195925RA R2125 10k OHM +-5% 1/16WR273 0195862RA R2125 33 OHM +-5% 1/10WR274 0195900RA R2125 1k OHM +-5% 1/10WR275 0195920RA R2125 6.8k OHM +-5% 1/16WR276 0195933RA R2125 22 k OHM +-5% 1/16WR277 0195941RA R2125 47k OHM +-5% 1/16WR278 0195925RA R2125 10k OHM +-5% 1/16WR279 0195950RA R2125 100k OHM +-5% 1/16WR280 0195900RA R2125 1k OHM +-5% 1/10WR281 0195900RA R2125 1k OHM +-5% 1/10WR282 0195950RA R2125 100k OHM +-5% 1/16WR283 0195925RA R2125 10k OHM +-5% 1/16WR284 0195910RA R2125 2.7k OHM +-5% 1/16WR285 0195910RA R2125 2.7k OHM +-5% 1/16WR286 0195950RA R2125 100k OHM +-5% 1/16WR287 0195950RA R2125 100k OHM +-5% 1/16WR288 0195950RA R2125 100k OHM +-5% 1/16WR289 0195950RA R2125 100k OHM +-5% 1/16WR291 0114147MA CF 470 OHM +-5% 1/4WR292 0195891RA R2125 470 OHM +-5% 1/10WR299 0195925RA R2125 10k OHM +-5% 1/16WX201 BG01341U SAWUK9462MX202 BG01351U SAWUM1956MX203 BG00721 SAWUG3962MX206 2142601A CERAMIC FILTER SFE 4.5MB9X207 2167212A CERAMIC FILTER SFE 6.0MB9X208 2142602A CERAMIC FILTER SFE 5.5MB9X209 2167213A CERAMIC FILTER SFE 4.5MB9X213 2142241A CERAMIC TRAP 4.5MHzX214 2167371 CFL-TRAP5.5/5.74X215 2143473 CERAMIC TRAP 6/6.5MHz

No. 51876

AV-4300AV-5000

51

TERMINAL P.W.B ASSY (6916201A)


CA01 0800003RA EL 1uF 50VCA02 0800003RA EL 1uF 50VCA03 0800003RA EL 1uF 50VCA04 0800003RA EL 1uF 50VCA05 0800003RA EL 1uF 50VCA06 0800003RA EL 1uF 50VCA07 0800003RA EL 1uF 50VCA08 0800003RA EL 1uF 50VCA26 0800015RA EL 10uF 16VCA27 0800015RA EL 10uF 16VCA28 0800015RA EL 10uF 16VCA29 0800015RA EL 10uF 16VCA31 0800015RA EL 10uF 16VCA33 0800015RA EL 10uF 16VCA38 0800041RA EL 47uF 16VCA39 0800041RA EL 47uF 16VCA40 0800015RA EL 10uF 16VCA41 0800015RA EL 10uF 16VCA45 0893044RA CD 2125 10000pF +-10% 50VCA46 0893044RA CD 2125 10000pF +-10% 50VCA51 0893044RA CD 2125 10000pF +-10% 50VCA52 0893044RA CD 2125 10000pF +-10% 50VCA53 0228754RA CD2125 100pF +-5% 50VCA54 0228754RA CD2125 100pF +-5% 50VCA55 0228754RA CD2125 100pF +-5% 50VCA56 0228754RA CD2125 100pF +-5% 50VCA59 0228754RA CD2125 100pF +-5% 50VCA60 0228754RA CD2125 100pF +-5% 50VCA61 0228754RA CD2125 100pF +-5% 50VCA62 0228754RA CD2125 100pF +-5% 50VCA63 0228754RA CD2125 100pF +-5% 50VCA64 0228754RA CD2125 100pF +-5% 50VCA65 0228754RA CD2125 100pF +-5% 50VCA66 0228754RA CD2125 100pF +-5% 50VCA75 0800003RA EL 1uF 50VCA76 0800003RA EL 1uF 50VCA80 0800015RA EL 10uF 16VCA81 0800015RA EL 10uF 16VCX01 0893044RA CD 2125 10000pF +-10% 50VCX02 0800049RA EL 100uF 16VCX03 0246448RA CD 22pF +-5% 50VCX04 0228036RA CD2125 18pF +-5% 50VCX05 0228010RA CD2125 10pF +-0.25pF 50VCX06 0800001RA EL 0.47uF 50VCX07 0893044RA CD 2125 10000pF +-10% 50VCX08 0893044RA CD 2125 10000pF +-10% 50VCX09 0893044RA CD 2125 10000pF +-10% 50VCX10 0228760RA CC2125 50V-180pF-J SLCX11 0893044RA CD 2125 10000pF +-10% 50VCX12 0228746RA CD2125 47pF +-5% 50VCX14 0893044RA CD 2125 10000pF +-10% 50VCX15 0893044RA CD 2125 10000pF +-10% 50VCX16 0893044RA CD 2125 10000pF +-10% 50VCX17 0800049RA EL 100uF 16VCX18 0893044RA CD 2125 10000pF +-10% 50VCX19 0893044RA CD 2125 10000pF +-10% 50VCX20 0893044RA CD 2125 10000pF +-10% 50VCX21 0800049RA EL 100uF 16VCX22 0893044RA CD 2125 10000pF +-10% 50VCX31 0800049RA EL 100uF 16VCX32 0893044RA CD 2125 10000pF +-10% 50VCX33 0228032RA CD2125 12pF +-05 50VCX35 0228032RA CD2125 12pF +-05 50VCX37 0893044RA CD 2125 10000pF +-10% 50VCX38 0893044RA CD 2125 10000pF +-10% 50VCX40 0893044RA CD 2125 10000pF +-10% 50VCX41 0228032RA CD2125 12pF +-05 50VCX43 0228032RA CD2125 12pF +-05 50VCX44 0284647RA CEL 16V 22uF(BP)CX45 0800049RA EL 100uF 16VCX46 0893044RA CD 2125 10000pF +-10% 50VCX47 0800015RA EL 10uF 16VCX48 0800049RA EL 100uF 16V


CX49 0800041RA EL 47uF 16VCX50 0800049RA EL 100uF 16VCX51 0800057RA EL 220uF 10VCX52 0800049RA EL 100uF 16VCX53 0893044RA CD 2125 10000pF +-10% 50VCX54 0800049RA EL 100uF 16VCX55 0893044RA CD 2125 10000pF +-10% 50VCX56 0800015RA EL 10uF 16VCX57 0800015RA EL 10uF 16VCX58 0800015RA EL 10uF 16VCX59 0800015RA EL 10uF 16VCX61 0800326A EL 100uF 16VCX62 0228054RA CD2125 100pF +-5% 50VCX63 0228054RA CD2125 100pF +-5% 50VCY01 0284647R CEL 16V 22uF(BP)CY02 0800023RA EL 22uF 16VCY04 0800023RA EL 22uF 16VCY05 0800023RA EL 22uF 16VCY07 0800023RA EL 22uF 16VCY08 0800049RA EL 100uF 16VCY09 0893027RA CT2125 25V-0.1uF-KCY10 0252396R EL 10uF 16V BPCY11 0800015RA EL 10uF 16VCY12 0800049RA EL 100uF 16VCY13 0893033RA CD 2125 1500pF +-10% 50VCY14 0800074RA EL 470uF 16VCY15 0880057RA PF 0.1uF +-10% 50VCY16 0800049RA EL 100uF 16VCY17 0800041RA EL 47uF 16VCY23 0800023RA EL 22uF 16VCY24 0800049RA EL 100uF 16VCY25 0893044RA CD 2125 10000pF +-10% 50VCY26 0800023RA EL 22uF 16VCY75 0800023RA EL 22uF 16VCY76 0800015RA EL 10uF 16VCY77 0228772RA CC733CH1H561JRCY78 0800012RA EL 4.7uF 50VCY79 0800049RA EL 100uF 16VCY80 0800015RA EL 10uF 16VCY81 0800015RA EL 10uF 16VCY82 0800049RA EL 100uF 16VCY83 0800049RA EL 100uF 16VCY84 0800049RA EL 100uF 16VCY85 0800015RA EL 10uF 16VCY86 0800015RA EL 10uF 16VCY87 0893044RA CD 2125 10000pF +-10% 50VCY88 0800015RA EL 10uF 16VCY89 0800015RA EL 10uF 16VCY90 0800015RA EL 10uF 16VCY91 0800015RA EL 10uF 16VCY92 0800015RA EL 10uF 16VCY93 0800015RA EL 10uF 16VCY94 0800015RA EL 10uF 16VCY95 0228772RA CC733CH1H561JRCY96 0800087 EL 2200uF 16VDA01 2344041M DI 1SS254TA/1SS270TADA02 2344041M DI 1SS254TA/1SS270TADA03 2348031M DIO-MTZ-J2.7ATADA04 2348031M DIO-MTZ-J2.7ATADA05 2344041M DI 1SS254TA/1SS270TADA06 2344041M DI 1SS254TA/1SS270TADA07 2348031M DIO-MTZ-J2.7ATADA08 2348031M DIO-MTZ-J2.7ATADA09 2348212M DIO-MTZ-J15BTADA10 2348212M DIO-MTZ-J15BTADA13 2344041M DI 1SS254TA/1SS270TADA14 2344041M DI 1SS254TA/1SS270TADA15 2348031M DIO-MTZ-J2.7ATADA16 2348031M DIO-MTZ-J2.7ATADY01 2344041M DI 1SS254TA/1SS270TADY02 2348212M DIO-MTZ-J15BTADY03 2348212M DIO-MTZ-J15BTADY04 2348212M DIO-MTZ-J15BTA

No. 51876

AV-4300AV-5000

52


DY05 2344041M DI 1SS254TA/1SS270TADY06 2344041M DI 1SS254TA/1SS270TADY07 2344041M DI 1SS254TA/1SS270TADY08 2344041M DI 1SS254TA/1SS270TADY09 2344041M DI 1SS254TA/1SS270TADY10 2344041M DI 1SS254TA/1SS270TADY11 2348212M DIO-MTZ-J15BTADY12 2344041M DI 1SS254TA/1SS270TADY13 2344041M DI 1SS254TA/1SS270TADY14 2344041M DI 1SS254TA/1SS270TADY15 2348212M DIO-MTZ-J15BTADY16 2348212M DIO-MTZ-J15BTADY17 2348212M DIO-MTZ-J15BTADY18 2344041M DI 1SS254TA/1SS270TADY19 2344041M DI 1SS254TA/1SS270TADY23 2344041M DI 1SS254TA/1SS270TADY24 2348212M DIO-MTZ-J15BTADY25 2344041M DI 1SS254TA/1SS270TADY26 2344041M DI 1SS254TA/1SS270TADY27 2344041M DI 1SS254TA/1SS270TADY28 2348031M DIO-MTZ-J2.7ATADY29 2348031M DIO-MTZ-J2.7ATADY30 2344041M DI 1SS254TA/1SS270TADY31 2344041M DI 1SS254TA/1SS270TAIX02 CP04841U TC9090ANIX03 2003981 IC BA7604NIY01 2020452 IC CXA1545ASIY02 5661161 IC HEF4053BJY01 ES00116 PJF-17PW/O 3.5KY102 0195248RA R3216 0 OHM 1/8WKY103 0195248RA R3216 0 OHM 1/8WKY105 0195250RA R2125 0 OHM 1/16WKY106 0195248RA R3216 0 OHM 1/8WKY107 0195248RA R3216 0 OHM 1/8WKY108 0195248RA R3216 0 OHM 1/8WKY125 0195248RA R3216 0 OHM 1/8WKY127 0195248RA R3216 0 OHM 1/8WKY128 0195248RA R3216 0 OHM 1/8WKY129 0195250RA R2125 0 OHM 1/16WKY130 0195250RA R2125 0 OHM 1/16WKY133

Documents

Jvc Av4300 Projection Tv Sm