Upload
vandiep
View
246
Download
11
Embed Size (px)
Citation preview
Brew Group removal instructions for Jura C, E, and F series:
Suitable for the following Jura Impressa models
JURA all IMPRESSA E, F, and C: E-Line: E10 * E25 * E30 * E40 * E45 * E5 * E50 * E55 * E60 * E65 * E70 * E74 * E75 * E80 * E85 F-Line: F9 * F90 * F70 * F5 * F50 C-Line: C5
1. Disclaimer:
This service manual describes the expansion and overhaul of the brewing unit of Jura E50. Services Unlimited Inc.Parts Guru is NOT responsible for any errors in understanding and repairs or use of
these instructions by inexperienced users.
2. Safety Warning:
A coffee machine uses water, heat, steam and electricity. Allow the machine to cool before repairing or servicing the machine. The thermo couples need up to 5 hours to cool down. Please work carefully and wisely. Read the instructions thoroughly before taking on repairs.Services Unlimited Inc./Parts Guru shall NOT be responsible for any damages to the property or any personal injuries while repairing the machine.
We sell only the Best espresso machines.
Guru's Choice: Jura XJ9, Jura Impressa X9 NSF; & Royal One Touch
We offer after sale service, parts, repairs & Tech support, like nowhere else
For Homes, Businesses, Restaurants, Corporate dining, Rentals, Catering & more
For routine maintenance of espresso machine: CLICK HERE for Espresso maintenance DOs & DON'Ts
PartsG
uru.co
m
Required Tools:
Normal screwdriver, Phillips screwdriver, oval head wrench, pliers, Torx TX20 and TX15 Torx (depending on model).
Magnet valve 110VJura grinder temperature sensorBrew group C,E,F,S series
Click picture to order online. If the link is broken, it will open the Home page. If so, type the desription in Quick search to open the page.
PartsG
uru.co
m
Coffee outlet hose support
Small gear brew drive motor Hose clamps set of threeOval head key
Jura water tank outlet valve kit
Jura membrane regulator hair pin type
Brew group maintenance kitE8 E9 Steam outlet Complete grinder 120V DC
Thermostat L=115C Clearyl filter cartridgeTransformer for all models
Step down 120V-9V
Membrane regulator Clamp type with 12" reinforced hose
Drip tray E Series
Brew group Piston O-ring pair with lube
Bullet tip nozzle
Dial component frother complete
Legis connetors Thermoblock
Click on the part to order online. If the link is broken, it will open the Home page. If so, type name of part in the Quick search to access.
Click Here to order parts online. If any link is broken, it will open the Home page. If so, type the name of part in Quick search to find it.
For Jura parts, repairs & tech support, contact:
Services Unlimited, Inc./ Parts Guru 209 Walnut street, Lansdale, PA 19446
Phone: 215-362-7000 Fax: 215-361-7434 email: [email protected]
Online store www.shop.partsguru.com
PartsG
uru.co
m
Dismantling the Machine
1. Unplug the machine. Remove the drip pans and water container.Empty the coffee bean hopper, so no coffee beans fall into the machine.
For Jura parts, repairs & tech support, contact:Services Unlimited, Inc./ Parts Guru
209 Walnut street, Lansdale, PA 19446 Phone: 215-362-7000 Fax: 215-361-7434
email: [email protected] Online store www.shop.partsguru.com
PartsG
uru.co
m
2. Use the oval head screw key to remove the oval head screws from the back of the machine.Rotate the key counterclockwise.
3. Unscrew the oval head screw gently without causing any damage to the machine.
For Jura parts, repairs & tech support, contact:Services Unlimited, Inc./ Parts Guru
209 Walnut street, Lansdale, PA 19446 Phone: 215-362-7000 Fax: 215-361-7434
email: [email protected] Online store www.shop.partsguru.com
PartsG
uru.co
m
4.
5.
Remove the upper screws using the phillips or Torx screw driver. Rotate counter clockwise
Remove the upper part completely carefully without damaging the side flaps
PartsG
uru.co
m
6.
7.
Remove the left side panel by gently sliding it backwards to disengage the tabs from the front panel. Once the tabs are unhooked, slowly remove the side panel.
Apply the same procedure to remove the right side panel as indicated in step 6.For Jura parts, repairs & tech support, contact:
Services Unlimited, Inc./ Parts Guru 209 Walnut street, Lansdale, PA 19446
Phone: 215-362-7000 Fax: 215-361-7434 email: [email protected]
Online store www.shop.partsguru.com
PartsG
uru.co
m
Remove the bolt from the brew drive gear motor using the Torx 20 or Phillips screw driver (depending on the model). Be sure to use the correct tool to remove the screw. Using the wrong tool may worn out the grooves hence making it difficult to remove the screw.
8.
Jura Grinder key to unblock Ring & Cone Grinder burrs
For Jura parts, repairs & tech support, contact:Services Unlimited, Inc./ Parts Guru
209 Walnut street, Lansdale, PA 19446 Phone: 215-362-7000 Fax: 215-361-7434
email: [email protected] Online store www.shop.partsguru.com
PartsG
uru.co
m
9.
10.
Remove the hair pin clip from the heating cartridge valve on the right side of the machine using the screw driver or the pliers.
Pull down the transparent silicone hose from the heater valve. Be sure to remove the seal/o-ring at the end of the silicone hose. It often remains inside the valve and can be removed using the screw driver.
PartsG
uru.co
m
11. Remove the screw from the water tank seal cover on the left side of the machine.
For Jura parts, repairs & tech support, contact:Services Unlimited, Inc./ Parts Guru
209 Walnut street, Lansdale, PA 19446 Phone: 215-362-7000 Fax: 215-361-7434
email: [email protected] Online store www.shop.partsguru.com
PartsG
uru.co
m
12.
13.
Slide out the water tank seal assembly slowly. No need to remove the hose inside theassembly.
Cut the cable ties at the ground coffee funnel
PartsG
uru.co
m
14.
15.
You may remove the gound coffee funnel but it's not necessary.
Unsrew the three highlighted screws using the phillips or Torx screw driver. Do not removeany other screws that are attached to the brew group guide.
PartsG
uru.co
m
16. Slide out the brew group slowly. Ensure that infuser pipe out of the brew groupto the coffee dispensing assembly is detached.
For Jura parts, repairs & tech support, contact:Services Unlimited, Inc./ Parts Guru
209 Walnut street, Lansdale, PA 19446 Phone: 215-362-7000 Fax: 215-361-7434
email: [email protected] Online store www.shop.partsguru.comPartsG
uru.co
m
17.
18.
Slide up the brew unit guide
Detach the infuser connector mounted atop the brew group. Leave the infuser hose attached
For Jura parts, repairs & tech support, contact:Services Unlimited, Inc./ Parts Guru
209 Walnut street, Lansdale, PA 19446 Phone: 215-362-7000 Fax: 215-361-7434
email: [email protected] Online store www.shop.partsguru.com
PartsG
uru.co
m
19. Detach the coffee sweeper/scraper from the brew group.
For Jura parts, repairs & tech support, contact:Services Unlimited, Inc./ Parts Guru
209 Walnut street, Lansdale, PA 19446 Phone: 215-362-7000 Fax: 215-361-7434
email: [email protected] Online store www.shop.partsguru.com
PartsG
uru.co
m
20. Brew Group without the brew group guide and coffee scraper.
PartsG
uru.co
m