July 2012 - BPC Building Products Ltd. · PDF fileConstruction Products July 2012 2012 BPC fixings catalogue FOR WEB_Layout 1 06/07/2012 12:04 Page 1

Construction ProductsJuly 2012
2012 BPC fixings catalogue FOR WEB_Layout 1 06/07/2012 12:04 Page 1

2 Tel 01924 364 794 BPC 2011/12
ContentsBPC Metalwork Brochure
NEW
NEW
NEW
NEW
NEW
Galvanised Heavy Duty Joist HangersJoist Hanger Type S 3Joist Hanger Type R 3Joist Hanger Type D 4Special Masonry Hangers 4Installation Details 5Safe Working Loads 5
Restraint StrapsHeavy Duty Straps 6Light Duty Straps 6Rolled Edge Restraint Straps 7Timber Frame Holding Down Straps 7Party Wall Straps 7Non-Standard Restraint Straps 7
Timber to Timber Joist HangersLight Duty Hanger - Short Leg 8Light Duty Hanger - Standard Leg 8Medium Duty Hanger - Standard Leg 9Medium Duty Hanger - Long Leg 9Mini Hanger 9
Timber Engineering HardwareTruss Clip 10Mono Truss Shoe 10Girder Truss Shoe 10Splice Plate 11Hand Nail Plate 11
Multi-Truss HangersType MTH/240 12Type MTH/340 12Type MTH/380 12Concealed Flange 12Type MTH/500 13Type MTH/560 13Type MTH/620 13
Angle BracketsAngle Plate 14Angle Bracket 14Flat Connector Plates 14Heavy Duty Angle Brackets 15Light Duty Corner Bracket 15Adjustable Angle Bracket 15T and L Brackets 15Light Duty Angle Braces 16Corner Stretcher Plate 16Corner Plate 16Mending Plates 16
Timber FixingsHerringbone Joist Strut 17Sole Plate Anchor 17Framing Anchor 17Safeplate 17Pallet Plates 18Holding Down Angles 18Glide Shoe 18Multi-Fix Strapping 18
NailsSheradised Square Twisted Nails 19Stainless Steel Annular Ring Shank Nails 19
Timber ConnectorsTooth Plate Connectors 19Split Ring Connector 20Shear Plate Connector 20Square Plate Washers 20
Frame CrampsFishtailed Frame Cramp 21Plain End Frame Cramp 21Safety End Frame Cramp 22Flexi-Chevron Tie 22Window Board Tie 22Screw-in Frame Tie 22
Wall TiesStandard Masonry to Masonry Wall Ties 23Timber Frame Ties 23Insulation Retaining Clips 23Universal Wall Starter Kits 24Starter Tie 24Butterfly Wire Ties 24Double-Triangular Wire Ties 24Safety End Movement Tie 25De-Bonding Sleeves 25Safety End Strip Tie 25
Bead & MeshStandard Angle Bead 26Thincoat Angle Bead 26Minimesh Angle Bead 26Stop Bead 26External Render Stop 27Expanded Metal Lath 27Rib Lath 27Fibreglass Self Adhesive Tape 27Corner Bead Tape 27Expanded Metal Brickwork Reinforcement 28Soffit Vent Mesh 28Stainless Steel Structural Bed Joint Reinforcement 28
Miscellaneous ProductsGallows Bracket 29Galvanised Weather Bar 29Hip Iron 29Joist Cap 30
Technical InformationHealth & Safety Data 31Quality Mangement System 31Technical Data 31

3www.bpcfixings.comManufactured in the UK
To order or find out more
call 01924 364 794or scan the QR code.
Galvanised Single PieceJoist HangersA comprehensive range of single piece non-welded timber tomasonry hangers, designed to support timber joists from brick or blockwalls. As standard all hangers are manufactured from 2.0mm thick pre-galvanised steel to BS EN 10346 : 2009, DX51D + G600 compliantwith BS6178: Part 1:1990 and to the requirements of BS5268.
Wide top flange design offers increased loading capacity on masonrywith a minimum crushing strength of 2.8N/mm2 and above. Hangers150mm deep and over are manufactured 10mm less to allow fornotching and regularisation of timber joists
All hangers feature 75mm bearing surface and pre-punched sidegussets to allow nail fixing into timber joists with 30 x 3.75mmsherardized square twist nails.
Type S (Standard)
The standard hanger is designed for building into brickwork or blockwork. Available in the following depths and widths.
Width 38mm, 44mm, 47mm, 50mm, 63mm, 75mm, 100mm, 125mm, 150mm
Depth 100mm, 125mm, 150mm*, 175mm*, 200mm*, 225mm*, 250mm*
Bearing surface 75mm
Order Code = SPMH/S/width x depth i.e. SPMH/S/50x200
Please NoteThe Type R Return Hanger is not a Restraint Hanger. Restraint Hangers are specials/manufactured to order.
Joist Hanger Type R (Return) Top Flange Up To 250mmThe return type hanger is designed for similar application to the Type S but with the advantage of a return flange (25mm as standard ) whichgreatly increases lateral support by giving the top flange additionalresistance to pull out. We would recommend the use of TYPE R returnflange hangers wherever possible for all timber to brick applications.
As standard the return hanger is manufactured to suit 100mm blockwork,however any length of top flange is available to order.
Depth 100mm 125mm 150mm* 175mm* 200mm* 225mm* 250mm*
Order Code = SPMH/R/width x depth(block size) i.e. SPMH/R/50x200 (100)
Joist Hanger Type S (Standard) Top Flange 75mm

4 Tel 01924 364 794 BPC 2011/12
Galvanised Heavy Duty Joist Hangers
Special Masonry HangersSpecial masonry hangers can be manufactured to suitapplications where unusually heavy loads occur. Availablein galvanised or stainless steel heavy gauge plate, tocustomer drawings.
BPC Metalwork Brochure
Joist Hanger Type D (Straddle) Top Flange Up To 250mm
A range of Stainless Steel timber tomasonry hangers are available to order.
*Please note: As standard all hangers 150mm deep andabove are manufactured 10mm less to allow forregularised timber and to ensure that joist levels aremaintained.
Please specify the type of hanger required together withthe following dimensions :
a. Width b. Depth c. Length of top flange on Type R and Type D only. Type S top flange is 75mm.
The straddle type joist hanger is used when timber joist positions are directly opposite each other on either side of a wall or beam. As standard the straddle hanger is manufactured to suit 100mm blockwork , however any width is available to order.
Depth 100mm 125mm 150mm* 175mm* 200mm* 225mm* 250mm*
Order Code = SPMH/D/width x depth(block size) i.e. SPMH/D/50x200(100)

SPMH Box Quantities
SPMH Safe Working Loads (kN)Masonry Strength 2.8 N/mm2
Nominal Joist SPMH Joist Widthsdepth depth 38 - 50 63 - 75 89 - 150
100mm 100mm 3.08 2.86 n/a125mm 125mm 3.21 2.86 n/a150mm 140mm 3.28 3.05 n/a175mm 165mm 3.40 3.07 n/a200mm 190mm 3.52 3.29 n/a225mm 215mm 3.65 3.43 n/a250mm 240mm 3.65 3.43 n/a275mm 265mm 3.65 3.43 n/a
Timber depth Timber Width38 44 47 50 63 75 89 100 125 150
100mm 50 40 40 40 40 40 30 30 n/a n/a125mm 45 40 40 40 40 30 30 20 15 n/a150mm 40 40 40 40 40 25 25 20 15 15175mm 30 30 30 30 30 20 20 20 15 10200mm 25 25 25 25 25 20 20 15 10 10225mm 25 25 25 25 25 20 20 15 10 10250mm 25 25 25 25 20 15 15 15 10 10
Masonry Strength 3.5 N/mm2
100mm 100mm 2.67 2.77 n/a125mm 125mm 2.86 2.98 n/a150mm 140mm 3.05 3.19 n/a175mm 165mm 3.25 3.40 n/a200mm 190mm 3.44 3.61 n/a225mm 215mm 3.63 3.82 n/a250mm 240mm 3.63 3.82 n/a275mm 265mm 3.63 3.82 n/a
100mm 100mm 2.84 2.93 4.17125mm 125mm 3.06 3.18 4.17150mm 140mm 3.19 3.33 4.08175mm 165mm 3.41 3.57 3.99200mm 190mm 3.64 3.83 3.90225mm 215mm 3.87 3.87 3.81250mm 240mm 3.87 3.87 3.81275mm 265mm 3.87 3.87 3.81
100mm 100mm 3.13 4.29 4.47125mm 125mm 3.55 4.62 4.47150mm 140mm 3.80 4.87 4.42175mm 165mm 4.22 5.22 4.36200mm 190mm 4.63 5.58 4.31225mm 215mm 5.05 5.94 4.25250mm 240mm 5.05 5.94 4.25275mm 265mm 5.05 5.94 4.25
5www.bpcfixings.comManufactured in the UK
To order or find out more
call 01924 364 794or scan the QR code.
Installation Details
The back plate of the joist hanger must be flush against thesupporting masonry.
A minimum of 675mm of cured masonry must be in positionabove the joist hanger flanges before any load is applied.
Timber joists should be cut square and butt up to the backface of the hanger with a maximum allowed gap of 6mm.
Nail to the timber joist through all pre-punched holes in eachside gusset with BPC 30x3.75mm sherardized square twistnails (see page 19).
It is recommended that ceiling joists are notched at thehanger base to achieve a level surface when usingplasterboards.
Type R return hangers and Type D straddle hangers alloweasy location and alignment of joists during construction.
Heavy Duty Restraint Straps must be used with all types ofSPMH joist hangers to provide lateral restraint.

Restraint StrapsHorizontal (30x5, heavy duty) and Vertical (30x2.5, lightduty) straps are multi holed at 25mm offset centres.Galvanised straps are manufactured from hot dippedgalvanised steel to BS EN 10346:2009 DX51D + G275.Stainless steel straps BS EN 10088-2 Grade 1.4301 areavailable to order.
Galvanised (edge coated) heavy duty restraint straps aresuitable for horizontal restraint applications such as tyingtimber roofs and floors into masonry walls. Light dutyrestraint straps can be used for vertical restraintapplications, such as holding down wall plates to masonry.
Designed in accordance with The Building Regulations,BS5268 Part 3 and other building standards for verticaland horizontal restraint.
Multi holed at 25mm offset centres, restraint strapsshould be fixed using either 50mm long no. 12woodscrews (using wall plugs in masonry for verticalrestraint) or 75mm x 4

Documents

July 2012 - BPC Building Products Ltd. · PDF fileConstruction Products July 2012 2012 BPC fixings catalogue FOR WEB_Layout 1 06/07/2012 12:04 Page 1