View
217
Download
0
Tags:
Embed Size (px)
Citation preview
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 2
Lighting Kits
• Before Borrowing Lighting Kits− Complete the online quiz− Score 100%
• Based on the material in this workshop
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 3
Lighting Kits
• Quartz Halogen vs Incandescent Lighting– Both operate on the same principle:
• Electric current passes through a thin tungsten metal filament causing it to heat white hot and emit light
– However, quartz halogen lamps encase the filament in a quartz casing filled with halogen gas. This allows these bulbs to run hotter, brighter and whiter
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 4
Lighting Kits
• Lighting Kits For Loan:– Lowel ViP Pro-light
• Low-level key or accent light, fill light (with diffusion) or back-light for interviews & other small shooting-areas
• 250w 120v• Max 8.3 Amps• Power cable 4.88m long
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 5
Lighting Kits
• Lighting Kits For Loan:– Ianiro Varibeam (red heads)
• 1000w & 600w• Spot-flood rear knob• Head cable 3.50m long• 4 leaf barn doors with gel clips
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 6
Lighting Kits
• Extras You Can Supply:– Wooden clothes pegs for fastening gels,
foils, etc.– Sandbags for weighting down equipment– Practical lighting from hardware stores:
• Utility lights:– Aluminum reflectors, ceramic sockets, etc.
• Windshield sunscreen as a reflector• Foam core whiteboard• Leather gloves for handling bulbs
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 7
Lighting Kits
• Safety First– Check all equipment for damage before use– Use at least 14 gauge extension cords– Tape down all cables (Gaffer’s tape)– Use ONLY in dry conditions– Always open the barn doors before turning a
lamp on– Never look directly at the lamps– Never pick up and move a lamp stand while
the lamp is on
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 8
Lighting Kits
• Safety First Cont’d– Do not operate the lamps pointing up or
down at a very steep angle (greater than 60 degrees) from the horizontal
– If smoke appears around the lamp or cables turn off the lamp and return it to the library
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 9
Lighting Kits
• Hot Lamps– These lights can get very hot!
• Use only approved accessories, e.g. gel frames• Only use approved bulb replacements and never touch
the new bulbs with bare hand (oil from your skin can cause them to explode when heated)
• Subjects will be affected by the lights• Keep all subjects/objects minimum 2 meters away • Keep all lamps and cables at least 6 meters away from
all flammable materials such as gas and oily rags
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 10
Lighting Kits
• Hot Lamps Cont’d• Do not touch the lamps without gloves for at least 20
minutes after turning them off• Wait at least 10 minutes after turning the lights off before
disassembling the lights
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 11
Lighting Kits
• Electric Safety Official– How to find the draw on a circuit
• Draw (amperage) = total power (watts) / voltage e.g. draw = 1000 watts / 120 volts = 8.3 amps
• Using this formula do not load a circuit more than approximately 80% of it’s maximum
- e.g. most household circuits are rated at 15 amps:
» 15 amps x 80% safety factor = 12 amps there for do not use more than 12 amps
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 12
Lighting Kits
• Electrical Safety Simpler– An alternate formula, with a safety factor
built in: draw = total power /100• e.g. draw = 1000 watts / 100 = 10 amps
– Using this formula, the 80% safety factor is built in so any circuit supporting at least 10 amps is fine for lamps totaling a 1000 watts
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 13
Lighting Kits
• Electrical Safety Simpler Cont’d– Note: the total power consumed is the sum
of all the lights on one circuit, so add together the watts for multiple lights
• e.g. 600 watt light + 1000 watt light = 1600 watts
– 1600 is too much power for one household circuit, so split the load onto different circuits
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 14
Lighting Kits
• Activity: Inventory Check– What is in the Kit:
• A set of 2 or 3 lamps• 2 or 3 sets of barn doors• 2 or 3 light stands• Operation and safety guide• Gaffer’s tape or duct tape• Leather Gloves • Spare bulbs• Gel frames are in the Lowel Kit only
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 15
Lighting Kits
• Activity: Inventory Check Cont’d– What’s not in the kit
• Gels• Weights e.g. sandbags • Umbrellas, reflectors, gobos• 14 gauge power extension cables
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 16
Lighting Kits
• Activity:– Setup and Assembly
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 17
Lighting Kits
• Assembly and Setup– Procedure:
• Assemble your lighting kits according to the instructions
• Recall what you learned about safety and…
• Configure the lighting kits according to the 3-point lighting diagram to the right
• After your setup is checked by your instructor, disassemble and return the kits
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 18
Lighting Kits
• Three Point Lighting– Position your key light 15° to 45° off the
subject-camera axis, and raise it approximately 30° from the horizontal.
– Always loosen the T-handle and thumb-screw locks on the lights before making adjustments.
– Place the fill on the opposite side of the camera from the key. It doesn’t have to be equal distance.
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 19
Lighting Kits
• Three Point Lighting– The fill can be physically lower than the key,
and is usually lower in intensity as well.– Use some diffusion gel on the fill light– The back light can be positioned opposite
the key, or directly behind the subject. Raise it high enough to get the rim lighting effect you want. You may have to hide the stand in some cases.
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 20
Lighting Kits
• Online Quiz:– www.lib.sfu.ca/about/surrey/equipment.htm
• Lighting kit workshop and quiz
http://www.lib.sfu.ca/surrey/equipmenthttp://cgi.sfu.ca/~sfusur/tutorials/lib/ 21
Lighting Kits
• Questions:– Contact the Library Media Technicians
• [email protected]• 778-782-7411
– Contact Media Coordinator• [email protected]• 778-782-7490