Upload
cachit
View
54
Download
10
Embed Size (px)
DESCRIPTION
Trituradora mandíbula JM HD1312
Citation preview
1312
_WPC
fro_v
er02
.fm
This document is valid for:
Serial no. / Machine no. Sign.
JAWMASTER™ 1312:06© Copyright 2004 Sandvik Rock Processing AB.All rights reserved. No parts of this document may be reproduced or copied in any form or by any means without written permission from Sandvik SRP AB. All data and information in this manual may be changed without further notice. Reservations for misprints.
Document number: R 222.307 enIssue: 20050221Version: 2
Sandvik Rock Processing ABStationsplan, SE-233 81 Svedala, SwedenTel: +46 40-40 90 00, Fax: +46 40-40 92 64www.sandvik.com
Wear Parts Catalog13
12_W
PC
01_v
er02
.fm
GeneralOrdering informationWhen ordering parts, always state the machine type and serial number according to the identification plate on the jaw crusher. State quantity, article number and denomination for each ordered part. (Quantities listed in this catalog are number of parts that are usually exchanged at the same time in a certain position or function.)
Identification plateThe figure below shows an example of the crusher’s identification plate. The identification plate contains data needed when contacting Sandvik SRP AB concerning wear parts.
Please enter the serial number of the associated machine in the intended field on the first page of this wear part catalog (the copyright page).
Think ahead!Avoid unnecessary downtime and increased freight charges by ordering parts well in advance.
1 2
1 Machine type2 Serial number
3JM 1312:06 © Sandvik Rock Processing AB – Doc. no. R 222.307 en Ver. 2
Wear Parts Catalog
1312
_WP
C01
_ver
02.fm
Adjustment shims
Cat. no. Qty. Part number Alternative Description Remarks5002-0 1 53-367-228-001 10 mm Adjustment shim
2 53-367-228-002 12 mm
1 53-367-228-003 15 mm
1 53-367-228-004 20 mm
3 53-367-228-005 25 mm
5002-0
4 © Sandvik Rock Processing AB – Doc. no. R 222.307 en Ver. 2 JM 1312:06
Wear Parts Catalog13
12_W
PC
01_v
er02
.fm
Clamping bars and deflector plate
Cat. no. Qty. Part number Alternative Description Remarks1210-0 2 10-214-355-000 Clamping bar stationary jaw
1211-0 4 17-104-245-006 Screw M42×580 stationary jaw
1211-1 4 845.0322-00 Nut M6M M42 stationary jaw
1211-3 4 00-921-224-142 Locking nut ML6M M42 stationary jaw
1211-5 8 89-442-690-011 Washer BRB 45/127×10 stationary jaw
1211-6 4 53-468-758-000 Flexible washer stationary jaw
3400-0 2 10-214-355-000 Clamping bar moving jaw
3401-0 4 59-942-843-002 Screw M42×1020 moving jaw
3401-1 4 845.0322-00 Nut M6M M42 moving jaw
3401-3 4 00-921-224-142 Locking nut ML6M M42 moving jaw
3401-5 8 89-442-690-011 Washer BRB 45/127×10 moving jaw
3401-6 4 53-468-758-000 Flexible washer moving jaw
3500-0 1 10-114-354-000 Deflector plate moving jaw
1210-01211-0
1211-51211-61211-51211-11211-3
3401-53401-63401-53401-13401-3
3500-03400-03401-0
5JM 1312:06 © Sandvik Rock Processing AB – Doc. no. R 222.307 en Ver. 2
Wear Parts Catalog
1312
_WP
C01
_ver
02.fm
Jaw plates
(Continued)
Cat. no. Qty. Part number Alternative Description Remarks1208-1 1 400.0447-001 C Jaw plate, stationary jaw corrugated
400.0422-001 CC coarse corrugated
400.0963-001 ST sharp teeth
400.0445-001 WT wide teeth
1209-0 2 53-366-632-501 Screw M42×750 stationary jaw
1209-1 2 845.0322-00 Nut M6M M42 stationary jaw
1209-3 2 00-921-224-142 Locking nut ML6M M42 stationary jaw
1209-5 4 89-442-690-011 Washer BRB 127/45×10 stationary jaw
1209-6 2 53-468-758-000 Flexible washer stationary jaw
3300-1 1 400.0446-001 C Jaw plate, moving jaw corrugated
400.0421-001 CC coarse corrugated
400.0964-001 ST sharp teeth
400.0445-001 WT wide teeth
3300-2 2 53-466-927-000 Wedge head M36 moving jaw
3301-0 2 53-366-926-000 Central stud M42 moving jaw
3301-1 2 845.0322-00 Nut M6M M42 moving jaw
3301-3 2 00-921-224-142 Locking nut ML6M M42 moving jaw
3301-5 4 89-442-690-011 Washer BRB 127/45×10 moving jaw
3301-6 2 53-468-758-000 Flexible washer moving jaw
1208-11209-0
1209-51209-61209-51209-11209-3
3301-03300-2
3301-53301-63301-53301-13301-3
3300-1
6 © Sandvik Rock Processing AB – Doc. no. R 222.307 en Ver. 2 JM 1312:06
Wear Parts Catalog13
12_W
PC
01_v
er02
.fm
The table below illustrates different jaw plate alternatives.
Jaw plate alternatives Stationary jaw Moving jaw
CorrugatedC
Coarse corrugatedCC
Sharp teethST
Wide teethWT
7JM 1312:06 © Sandvik Rock Processing AB – Doc. no. R 222.307 en Ver. 2
Wear Parts Catalog
1312
_WP
C01
_ver
02.fm
Wear plates
Support bars
Cat. no. Qty. Part number Alternative Description Remarks1300-0 1 53-466-616-000 Wear plate stationary jaw
3100-0 1 53-466-616-000 Wear plate moving jaw
Cat. no. Qty. Part number Alternative Description Remarks1205-0 1 10-314-356-000 Support bar stationary jaw
1206-0 7 840.1181-00 Screw M6S M30×220 stationary jaw
1206-1 14 845.0013-00 Nut M6M M30 stationary jaw
1206-2 7 847.0125-00 Washer BRB 31×58 stationary jaw
3200-0 1 10-314-356-000 Support bar moving jaw
3201-0 7 840.1086-00 Screw M6S M30×260 moving jaw
3201-1 14 845.0013-00 Nut M6M M30 moving jaw
3201-2 7 847.0125-00 Washer BRB 31×58 moving jaw
3100-01300-0
3200-0 3201-13201-23201-0
1206-1 1206-01206-2 1205-0
8 © Sandvik Rock Processing AB – Doc. no. R 222.307 en Ver. 2 JM 1312:06
Wear Parts Catalog13
12_W
PC
01_v
er02
.fm
Cheek plates
Cat. no. Qty. Part number Alternative Description Remarks1103-1 1 10-214-351-000 Cheek plates, upper left side
1103-2 1 10-214-352-000 Cheek plates, lower left side
1104-1 1 10-214-351-000 Cheek plates, upper right side
1104-2 1 10-214-352-000 Cheek plates, lower right side
1106-0 22 840.0678-00 Screw M6S M24×160 both sides
1106-1 22 845.0387-00 Locking nut M24 both sides
1106-2 22 847.0124-00 Washer BRFB 25×45 both sides
1106-4 22 402.4720-01 Flexible washer both sides
1106-5 22 402.4721-01 Steel washer 26/105×10 both sides
1106-01106-41106-51106-21106-1
1104-1 1104-2 1103-1 1103-2
9JM 1312:06 © Sandvik Rock Processing AB – Doc. no. R 222.307 en Ver. 2
Wear Parts Catalog
1312
_WP
C01
_ver
02.fm
This page is intentionally left blank
10 © Sandvik Rock Processing AB – Doc. no. R 222.307 en Ver. 2 JM 1312:06