EK-6

800-839-8823 www.creform.com

SV-22

I.D. Deburring Cutter

ID/OD DEBUR

I.D/O.D. Deburring Tool

CreformTools

G-�

se

CTIo

N

G

Creform Pipe should always be cut using a pipe cutter, band saw or chopsaw — never use a hand saw to cut pipe as this will frequently result in pipe sections not cut to the required lengths and pipe ends out of square.

These conditions can effect the fit and strength of your Creform structures.

Please read all instructions and familiarize yourself with proper procedures prior to using the Creform EPC Pipe Cutter or EK-1 Manual Pipe Cutter. ALWAYS WEAR APPROPRIATE EYE PROTECTION.

When cutting, always hold the longest length of pipe.

Electric ø28 Pipe Cutter

EPC1

EK-1

Manual ø28 & ø32 Pipe Cutter

EK-1A

Manual Pipe Cutter Blade Set

Electric Pipe Cutter Blade

EPC1A

SV-22A Replacement Blade

EK-6A Replacement Blade

I.D. Deburring Cutter for Drill

Manufacturer:Jet

Creform P/N:Bandsaw J1

Our Price:$445.00

UL listed single phase motor●

Exclusive design heavy-duty 14 gauge stand●

Large diameter wheels and built-in handle allowseasy movement

●

Front legs have adjustable leveling pads●

Ball bearing supported blade wheel●

Full adjustable ball bearing blade guides●

Heat treated and ground steel worm gear withbronze drive gear

●

Three blade speeds to choose from●

Automatic shut-off after cut●

Standard EquipmentVertical work table●

Carbon steel blade●

Adjustable material stop●

SpecificationsModel HVBS-56MStock Number 414458Round Capacity at 90 degrees (in): 5Round Capacity at 45 degrees (in): 3Rectangle Capacity at 90 degrees (in):5 x 6Rectangle Capacity at 45 degrees (in):5 x 3Throat Depth (in): 6Vertical Workable (in): 9-5/8 x 9-1/2Vise Swivels: 45 degreesBlade Size (in) 1/2 x .025 x 64-1/2Blade Wheel Diameter (in): 7-3/8Blade Speeds (SFPM): 80, 120, 200Blade Height (in): 25-1/2Floor Space Required (in): 19 x 44Motor: 1/2 HP, 1 Ph 115/230V Prewired 115VNet Weight (lbs): 115

Power Saw for Cutting Creform Pipe and Conveyor

Creform Corporation, PO Box 830, Greer, SC 29652-0830 www.Creform.comPhone:864-877-7405 Fax:964-877-3863

M6-L

6mm Hex Wrench

M6-L

6mm Hex Wrench, T-Handle

5MTM

Metric Tape Measure

Adhesive Bellows with Needle

BELLOW

CW-32

Caster Wrench for ESC Casters

800-839-8823 www.creform.com

CreformTools

G-2

se

CTIo

N

G

RTK1

Caster Wrench for YGR Casters

EK-20

NDL-1

Needle Spout, Adhesive

EY-204

Adhesive Bottle with Needle

5mm Hex Wrench

M5-L

Rubber Mallet

RM-01

5mm Hex Wrench, T-Handle

M5-T

In addition to the EPC Pipe Cutter and the EK-1 Manual Pipe cutter, the tools below are available from Creform, intended to make fabrication and construction of Creform Structures easier and faster.

RTK1C

RTK1A

RTK1B

Set: Ratchet Handle, 13mm Socket, 5mm Hex Bit

EK-6A

EK-6 EK-4BEK-4A

SU7-4000-SUS

EK-4

EK-3EK-2

ø28 Length(mm)

EK-2A EK-3A

800-839-8823 www.creform.comESD anti static

I-7

se

ctIo

n

I

Notes:• High temperature applications up to 300°F

(140°C).• Higher chemical resistance uses since material

is 304SS.• The pipe is grooved at joint locations to add

strength.

Stainless Steel Pipe

Material: Polished 304 Stainless Steel.Used to Form: General Creform Structures. Carts, workstations, flow racks, etc.Note: ø27 pipe. Standard length 4M.

Creform Standard 27mm Pipe Strength

* Proportional Limit refers to the point where any further force would permanently deform the pipe.

A Dimension Proportional Limit 900mm (2'11") 97kg (213 lbs.)

• The pipe rests freely at room temperature on two supports• A force is applied at 1/2 A at a speed of 50mm/min

Experimental Conditions

Manual Pipe Cutter for SUS Pipe

Manual Pipe Cutter Blade Set

Manual Grooving Cutter for SUS Pipe

Manual Grooving Cutter Blade Set

Electric Pipe Cutter - Groover for SUS Pipe

Dimensions are in millimeters.

creform

stAInLess steeL PIPe - 27mm

Electric SUS Pipe Cutter Blade Set

Electric SUS Pipe Grooving Cutter Blade Set

ID Deburring Tool for Electric Drill

Replacement Blade