JAMIESON MANUFACTURING CO.€¦ · trustrac™ installation guide did you know? jamieson supplies installation tools. contact your jamieson dealer prior to order for more information

www.jamiesonfence.com

JAMIESON MANUFACTURING CO.

TRUSTRAC™ INSTALLATION GUIDE

SINGLE TRACK CANTILEVER SLIDING GATES

NOTE: THESE INSTALLATION GUIDELINES ARE BASED ON A LEVEL GRADE FROM OPENING THROUGH ENTIRE ROLL-BACK AREA. DEVIATIONS FROM LEVEL

CONDITIONS (i.e.: curbs, sloped conditions, etc) MUST BE ADDRESSED & ADJUSTED ACCORDINGLY PRIOR TO INSTALLATION OF THE POST ASSEMBLIES


SSAAFFEETTYY PPOOLLIICCYY

JAMIESON MANUFACTURING CO IS COMMITTED TO PROVIDING QUALITY GATE PRODUCTS AND SERVICES. BECAUSE SAFETY IS AN IMPORTANT PART OF

JAMIESON'S DESIGN AND MANUFACTURING CRITERIA, WE FOLLOW THE STANDARDS DEVELOPED BY UNDERWRITER'S LABORATORY (UL325) AND ASTM F2200-02 AS DEVELOPED BY ASTM INTERNATIONAL. WHILE THESE SAFETY STADARDS ARE

SPECIFIC TO AUTOMATED GATES, JAMIESON ALSO CHOOSES TO APPLY THEM TO MANUAL GATES TO RESTRICT HAZARDS SUCH AS PROTRUSIONS, PINCH POINTS AND ENTRAPMENT ZONES IN CASE A GATE IS AUTOMATED AT A LATER DATE. FOR MORE INFORMATION ABOUT JAMIESON GATES, PLEASE NOTIFY YOUR NEAREST JAMIESON

MANUFACTURING CO. OR JAMIESON FENCE SUPPLY REPRESENTATIVE.

COPYRIGHT © 2007 BY JAMIESON MANUFACTURING CO. ALL RIGHTS RESERVED.

NOT PART OF THIS PUBLICATION MAY BE REPORDUCED BY ANY PROCESS, ELECTRONIC OR OTHERWISE, IN ANY MATERIAL FORM OR TRANSMITED TO ANY OTHER PERSON OR STORED ELECTRONICALLY IN ANY FORM, WITHOUT THE PRIOR WRITTEN PERMISSION OF JAMIESON

MANUFACTURING CO.

DO NOT DISABLE , REMOVE OR MODIFY

ANY SAFETY FEATURES FROM THE PRODUCT

DO NOT ADD ANY FEATURES THAT PROTRUDE FROM THE

BODY OF THE GATE GREATER THAN ½”

ALWAYS USE PROPER SAFETY EQUIPMENT WHEN

SERVICING GATE OR GATE HARDWARE

USE PROPER CARE & PRECAUTION AT ALL TIMES WHEN

OPERATING GATES

INSTALL ALL WARNING SIGNS &

PLACARDS NEVER “RIDE” THE GATE

FOR FURTHER INFORMATION

WWW.ASTM.ORG WWW.DASMA.COM

WWW.UL.COM

12300-A AMELIA DRIVE HOUSTON, TX 77045

888/286-3362 WWW.JAMIESONFENCE.COM

THERE IS NO SUBSTITUTE FOR COMMON SENSE

INSIDE FRONT COVER




Recommended Tools:

Tape measure Surveyors instrument String line Stakes String line level 24” to 48” Carpenter’s level

Post hole auger (or digger) Cement Trowel Fence Pliers Standard (flat) screwdriver 15/16” Open end wrench 15/16” Socket, ratchet & drive extension ¾” socket or open (or box) end wrench 6” or 8” crescent wrench

Single Track Parts List:

POST TRUCK BRKT. U-BOLT LOWER GUIDE BRKT. COLLECTOR4" ROUND 274003-E4 209007 274005-UL 274011-UL4" SQUARE 274003-E4 209007-SQ 274005-UL 274011-UL

6 5/8" ROUND 274003-E6 200000-265 274005-6 274012-UL6" SQUARE 274003-E6 200000-269 274005-6 274012-UL

TABLE III: HARDWARE GUIDE

WIRE SIZE3/16"1/4">30' 1/2" x 6"

TABLE IV: CABLE TRUSSINGGATE OPENING TURNBUCKLE SIZE

<30' 3/8" x 6"

EXTENDED TRUCK BRACKET(REF. TABLE III)

TABLE 1: TRUCK ASSEMBLY CRITERIA:

TRUSS CABLE(REF. TABLE IV)

BOTTOM HORIZONTAL

CABLE CLAMP

9 GA. SMOOTH WIRE

TENSION BAR

1/4" GUSSETTYP AT EACH CORNER/ EACH BAY

TURNBUCKLE(REF. TABLE IV)

SQUARE/ ROUND UL COLLECTOR(REF. TABLE III)TOP HORIZONTAL

BARBWIRE 4 PT. 12.5 GA.(OPTIONAL)

T6061-T6 ALUM. TRUSS TRAC

LOWER GUIDE BRACKET(REF. TABLE III)

3" UL BOX ROLLERS

> 24'

GATE OPENING

= 24'

274010

PARTNUMBER

274006

10"

LENGTH

6"

8

# BEARINGS/ WHEELS

4

NOTE: ALL SERIES 3000 GATES USE 10" TRUCKS




GATE OPENINGFENCE LINE FENCE LINE

ENTRY

EXIT

POINT A POINT B

SECURED AREA(INSIDE PROPERTY LINE)

UNSECURED AREA(OUTSIDE PROPERTY LINE)

STRING LINE

FENCE LINE ALIGN STRINGLINETO OUTSIDE POST

SURFACE

LINE/ENDPOST

GATE OPENINGFENCE LINE FENCE LINE

DID YOU KNOW?

JAMIESON GATES CAN BE INSTALLED FOR OPEN/CLOSE IN EITHER DIRECTION

ENTRY

EXIT

STEP 1: LAYOUT WORK AREA. ENSURE:

a) LEVEL GRADE (IF POSSIBLE). b) ADEQUATE SPACE IN DRAWBACK AREA. c) OBSTRUCTIONS CLEARED.



(APPROXIMATELY 50% OF GATE OPENING)

DRAWBACK AREA

COUNTERBALANCE AREA

= OVER ALL LENGTH OF GATE + CLEARANCE(TYPICALLY 1-12 x THE GATE OPENING)

INCLUDE POST SET BACK DISTANCE FROM CURB & ROADWAYEACH SIDE OF GATE OPENING

STEP 2: SIZE THE GATE ACCORDING TO THE GATE OPENING. INCLUDE CLEARANCES REQUIRED TO CLEAR THE CURB AND ROADWAY.

CURB CUTOUTS MAY BE REQUIREDTO MAINTAIN MINIMUM CLEARANCEBETWEEN BOTTOM OF GATE ANDGRADE

STEP 3: TO DETERMINE THE OUTSIDE FACE OF THE GATE POSTS, USE STRING LINE, SURVEYORS INSTRUMENT, OR OTHER ACCEPTABLE MEANS TO ESTABLISH A REFERENCE PLANE FROM POINT A TO POINT B (ACROSS COUNTERBALANCE AREA THROUGH GATE OPENING)

THE OVER ALL LENGTH OF A CANTILEVER GATE IS TYPICALLY 1.5 x THE GATE OPENING.

PG 1 OF 12




FENCE LINE FENCE LINE


STRING LINE

GATE OPENINGINSIDE-TO-INSIDE MEASURE

(INCLUDING CLEARANCE)


ENTRY

EXIT

STEP 5: MEASURE FROM INSIDE FACE OF LATCH POST ACCROSS ROADWAY TO MARK INSIDE FACE OF FRONT CANTILEVER GATE POST ON OPPOSITE SIDE OF ROADWAY


DID YOU KNOW? JAMIESON GATES CAN BE INSTALLED ON OUTSIDE OF FENCELINE. CONTACT YOUR JAMIESON DEALER PRIOR TO ORDER FOR MORE INFORMATION.

12 OF GATE OPENING

(TO INSIDE OF LATCH POST)

LAYOUT POST HOLES


ENTRY

EXIT

12 OF LATCH POST DIAMETER

STEP 4: SET MARKER FOR LATCH POST AT DESIRED LOCATION (OUTSIDE OF ROADWAY & CURB). (DISTANCE FROM CENTER OF ROADWAY SHOULD MEASURE 1/2 OF DESIRED GATE OPENING).

IMPORTANT: THE GATE OPENING MEASUREMENT IS FROM

INSIDE POST TO INSIDE POST

PG 2 OF 12




DID YOU KNOW? JAMIESON SUPPLIES INSTALLATION TOOLS. CONTACT YOUR JAMIESON DEALER PRIOR TO ORDER FOR MORE INFORMATION.

GATE OPENINGCANTILEVER POST SPACEOUTSIDE-TO-OUTSIDE MEASURE


ENTRY

EXIT

STEP 6: LOCATE BACK CANTILEVER POST (REFERENCE CHART)



STEP 7: EXCAVATE POST FOOTINGS

GATE OPENINGCANTILEVER POST LOCATIONS

LATCH POSTLOCATION

FINISHED GRADE

FOOTING DIA = 4x POST DIA MINIMUM UNLESS OTHERWISE SPECIFIED

AERIAL VIEW

ELEVATION VIEW

FOOTING DEPTH 3 FT MIN(6" DEEPER THAN POST DEPTH) UNLESS OTHERWISE SPECIFIED

IMPORTANT:CANTILEVER POST SPACINGS ARE FROM

OUTSIDE-TO-OUTSIDE OF POST!!

40'-0" 16'-0" 58'-0"

36'-0" 15'-0" 53'-0"38'-0" 15'-0" 55'-0"

32'-0" 14'-0" 48'-0"34'-0" 14'-0" 50'-0"

28'-0" 12'-0" 42'-0"30'-0" 13'-0" 45'-0"

24'-0" 11'-0" 36'-0"26'-0" 12'-0" 39'-0"

20'-0" 9'-0" 30'-0"22'-0" 10'-0" 33'-0"

16'-0" 7'-0" 24'-0"18'-0" 8'-0" 27'-0"

12'-0" 5'-0" 18'-0"14'-0" 6'-0" 21'-0"

8'-0" 3'-0" 12'-0"10'-0" 4'-0" 15'-0"

TABLE I: GATE SPECSGATE OPENING POST SPACING GATE OAL

PG 3 OF 12




GATE OPENING

LATCH POST

MEASURE BOTH HIGHAND LOW TO ENSURE

POSTS PARALLEL

STEP 8: POSITION POSTS IN EXCAVATED FOOTINGS USING STRING LINE AND LEVEL AS A GUIDE. BRACE THE POSTS TO ENSURE THEY STAY LEVEL, CO-LINEAR & PARALLEL

USE LEVEL IN PLANE OF FENCE LINE AND PERPENDICULAR TO FENCE LINE

BLOCK 6" OFFBOTTOM OF

FOOTING HOLE

TEMPORARY BRACING TO ENSURE POST STAY AT

TRUE VERTICAL

NOTE: DOUBLE CHECK ALL DIMENSIONS BEFORE NEXT STEP

GATE OPENING

STEP 9: POUR CONCRETE

CROWN CONCRETETO SHED WATER

GATE OPENING

STEP 10: REMOVE BRACING AND CLEAN UP WORK AREA

DID YOU KNOW? JAMIESON SELLS CONCRETE & BRACING FOR YOUR INSTALLATION NEEDS. CONTACT YOUR NEAREST JAMIESON FENCE SUPPLY DEALER FOR DETAILS.

PG 4 OF 12




MEASURE HEIGHT FROM GATE BOTTOM TO TOP INSIDE SURFACE OF

TRACK

U-BOLT

2" x 5" RECTANGULARBOTOM FRAME

OUTSIDEFENCELINE(UNSECURED)

TRUCK & TRUCK BRACKET

ALUMINUM TRACK/FRAME MEMBER

+ 3"

= HEIGHT TO SET BRACKET ABOVE

GRADE

a) MEASURE DISTANCE FROM THE BOTTOM OF THE GATE TO THE BOTTOM INSIDE SURFACE OF THE ALUMINUM TRACK

THIS SURFACESTEP 8: ATTACH TRUCK BRACKETS TO POST

- 3"TYPICAL GAPABOVE GRADE

CANTILEVER GATE POST

b) SINCE THE DISTANCE FROM THE TOP OF THE BRACKET TO THE TOP OF THE TRUCK IS OFFSET BY THE CLEARANCE BETWEEN THE BOTTOM OF THE GATE & THE GRADE ...

b) ... MOUNT EACH BRACKET TO A CANTILEVER POST USING THE U-BOLTS PROVIDED A DISTANCE EQUAL TO THAT MEASURE IN STEP 8a.

CANTILEVER GATE

PG 5 OF 12




OUTSIDEFENCELINE(UNSECURED)

TRUCK & TRUCK BRACKET

SET HEIGHT TO 3"

a) REMOVE LOCKNUT FROM TRUCK MOUNTING BOLTb) FIT TRUCK MOUNTING BOLT INTO MATING HOLE ON BRACKET c) USE ADJUSTING NUT TO SET HEIGHT TO APPROX 3" AS SHOWNd) REPLACE LOCKNUT AND TIGHTEN

STEP 9: MOUNT TRUCKS ONTO BRACKETS

REPEAT FOR 2ND TRUCK

e) STRETCH STRINGLINE BETWEEN TRUCKS OR BRACKETSf) USING LINE LEVEL TO CHECK IF LEVELg) ADJUST TRUCKS AS REQUIRED

LOCKNUT

ADJUSTING NUT

STEP 9b: CHECK LEVEL ACCROSS TRUCKS

STEP 10: MOUNT GATE

NOTE: GATE CAN BE INSTALLED FROM GATE OPENING SIDE OR DRAWBACK AREA SIDE- WHICHEVER IS MORE OPEN OR CONVENIENT.

> STAND GATE UPRIGHT> POSITION ENCLOSED TRACK ON GATE IN LINE WITH TRUCKS.> REMOVE CARRIAGE BOLT & NUT FROM END OF TRACK> ELEVATE GATE FOR TRUCKS TO ENTER TRACK> SLIDE GATE ONTO TRUCKS> CENTER GATE ON CANTILEVER POSTS> REPLACE CARRIAGE BOLT STOP AT END OF TRACK

NOTE: GATE IS HEAVY AND UNSTABLE. USE CAUTION WHEN MOVING. REQUIRES THE USE OF CRANE, FORKTRUCK, BOBCAT OR OTHER LIFTING & MOVING EQUIPMENT.

PG 6 OF 12




GATE OPENING

BACKCANTILEVER

POST

> PLACE LEVEL ON TOP SURFACE OF GATE BETWEEN CANTILEVER POSTS> ADJUST TRUCK LEVELLING NUTS UNTIL GATE HANGS LEVEL (REF DRAWING IN STEP 9)> TIGHTEN TRUCK LOCKNUTS

STEP 11: MOUNT LOWER ROLLER GUIDE & LEVEL GATE IN VERTICAL PLANE BY ADJUSTING ROLLERS APPROPRIATELY IN THE LOWER GUIDE SLOT

FRONTCANTILEVER

POST

LATCHPOST

STEP 13: LEVEL GATE IN CENTERED POSITION (CENTERED ON CANTILEVER GATE POSTS)

ADJUST ROLLER IN/OUTTO MAKE GATE VERTICAL

LEVEL

MOUNT LOWER GUIDETO POST WITH UBOLTPROVIDED

MINIMAL CLEARANCE

GATE WILL WANT TOLIST IN THIS DIRECTION

BEFORE ADJUSTING GUIDE WHEELS

INSTALL 2ND GUIDE ROLLER

DO NOT OVER-TIGHTENBACK GUIDEWHEEL SHOULD HAVE AIR SPACEBETWEEN FRAME & ROLLER

STEP 12: CHECK TENSION ON TRUSS CABLES

1

2

3

LEVEL

WITH GATE STILL IN CENTERED POSITION, ADJUST TURNBUCKLES SO THAT TRUSS CABLES ARE EVENLY TENSIONED (APPROXIMATELY 14" DEFLECTION)

GATE OPENING

BACKCANTILEVER

POST

FRONTCANTILEVER

POST

LATCHPOST

NOTE: DO NOT OVERTIGHTEN CABLES AT THIS POINT

REPEAT PROCEDURE FOR 2ND CANTILEVER GATE POST

LOWER GUIDE INSTALLED ON 6-5/8” RND POST

PG 7 OF 12




STEP 14: TRUSS CABLE ADJUSTMENT (1st SIDE) (GATE IN CENTERED POSITION UNTIL STEP 16)

VISUALIZE DIVIDING LINE IN MIDDLE OF GATE. EACH HALF IS ADJUSTED SEPERATELY & AS A MIRROR IMAGE OF EACH OTHER.

GATE OPENING

BACKCANTILEVER

POST

FRONTCANTILEVER

POST

LATCHPOST

ADJUST FRONT OF GATE TOLEVEL OR SLIGHT LIFT

PULL THE FRONT HALF OF THE GATE UP INTO A "SMILE" BY TIGHTENING THE FRONT TURNBUCKLES

GATE OPENING

BACKCANTILEVER

POST

FRONTCANTILEVER

POST

LATCHPOST

TIGHTEN THESE TURNBUCKLES PULLING IN THIS DIRECTION. NOTE: YOU CAN EITHER TIGHTEN FROM THE NOSE TO THE CENTER OR FROM THE CENTER OUT.

DO NOT ADJUST(NOTE: THESE CABLES WILL BECOME SLACK ASTHE OPPOSING CABLE IS TIGHTENED. DO NOT TAKE THE SLACK OUT OF THESE CABLES..

ON THE FRONT SIDEOF THE GATE, CABLES

ORIENTED IN THIS DIRECTION WILL PULL

THE GATE UP

ADJUST FRONTHALF OF GATE FIRST

FRONT HALF OF GATE

IF GATE HAS EXTENSIVE "SAG",YOU MAY CHOOSE TO USE A "HOUSE JACK" OR BLOCK &

PRY-BAR TO ELEVATE THE FRONTHALF OF THE GATE. THIS WILL

REDUCE THE AMOUNT OF TENSIONON THE TRUSS CABLE, MAKING IT

EASIER TO ADJUST

CL

LIFT TO LEVEL ORPLACE IN SLIGHT "SMILE"

AFTER TRUSS CABLE ADJUSTMENT ON THIS SIDE, CHECK WITH LEVEL TO ENSURE GATE DOES NOT SAG OR HAS SLIGHT SMILE.

GATE OPENING

BACKCANTILEVER

POST

FRONTCANTILEVER

POST

LATCHPOST

MAKE WHATEVER ADJUSTMENTSNECESSARY TO BRING GATE INTO

PROPER POSITION

FRONT HALF OF GATE

CL

CL

LEVEL

PG 8 OF 12




STEP 15: TENSION TRUSS CABLES (2nd SIDE) (GATE STILL IN CENTERED POSITION)

NOW ADJUST BACK HALF OF GATE. ADJUSTMENT PROCEDURE IS A MIRROR IMAGE OF THAT DONE IN STEP 14.

GATE OPENING

BACKCANTILEVER

POST

FRONTCANTILEVER

POST

ADJUST BACKOF GATE TOLEVEL OR SLIGHT LIFT

PULL THE BACK HALF OF THE GATE UP INTO A "SMILE" BY TIGHTENING THE BACK TURNBUCKLES

GATE OPENING

BACKCANTILEVER

POST

FRONTCANTILEVER

POST

TIGHTEN THESE TURNBUCKLESNOTE: YOU CAN EITHER TIGHTEN FROM THE NOSETO THE CENTER OR FROM THE CENTER OUT.


ON THE BACK SIDEOF THE GATE, CABLES


THE GATE UP

ADJUST BACKHALF OF GATE FIRST

BACK HALF OF GATE




EASIER TO ADJUST

CL


AFTER TRUSS CABLE ADJUSTMENT ON THIS SIDE, CHECK WITH LEVEL TO ENSURE GATE DOES NOT SAG OR HAS SLIGHT SMILE.

GATE OPENING

BACKCANTILEVER

POST

FRONTCANTILEVER

POST


PROPER POSITION

BACK HALF OF GATE

CL

CL

LEVEL

PG 9 OF 12




GATE OPENING

LATCH POSTNOT SHOWN

FOR ILLUSTRATIONPURPOSES

STEP 16: ADJUST TRUSS CABLES IN EXTENDED POSITIONS (GATE EXTENDED IN CLOSED POSITION)

VISUALIZE DIVIDING LINE AT FRONT CANTILEVER GATE POST.

BACKCANTILEVER

POST

FRONTCANTILEVER

POST

AS DONE IN STEP 14, ADJUST THE FRONT HALF OF THE GATE UP TO LEVEL OR A "SMILE" BY TIGHTENING THE FRONT TURNBUCKLES



ON THE FRONT SIDEOF THE GATE, CABLES


THE GATE UP

ADJUST FRONTHALF OF GATE FIRST




EASIER TO ADJUST


THEN CHECK WITH LEVEL TO ENSURE GATE MAINTAINS LEVEL OR HAS SLIGHT SMILE.

LATCHPOST


PROPER POSITION

LEVEL

GATE OPENING

BACKCANTILEVER

POST

FRONTCANTILEVER

POST

FRONT HALF OF GATE

EXTEND GATE TO FULLY CLOSED POSITION

GATE OPENING

BACKCANTILEVER

POST

FRONTCANTILEVER

POST

FRONT HALF OF GATE

PG 10 OF 12




THE REST OF THE GATE OPENING AND

LATCH POSTNOT SHOWN


STEP 17: FINAL ADJUSTMENT OF TRUSS CABLES (GATE EXTENDED IN OPEN POSITION)

VISUALIZE DIVIDING LINE AT BACK CANTILEVER GATE POST.

BACKCANTILEVER

POST

FRONTCANTILEVER

POST

AS DONE IN STEP 15, ADJUST THE BACK HALF OF THE GATE UP TO LEVEL OR A "SMILE" BY TIGHTENING THE BACK TURNBUCKLES



ON THE BACK SIDEOF THE GATE, CABLES


THE GATE UP

ADJUST BACKHALF OF GATE




EASIER TO ADJUST


THEN CHECK WITH LEVEL TO ENSURE GATE MAINTAINS LEVEL OR HAS SLIGHT SMILE.


PROPER POSITION LEVEL

NOW EXTEND GATE TO FULLY OPEN POSITION

GATE OPENINGGATE IN FULLY

OPEN POSTITION


LATCH POSTNOT SHOWN


BACKCANTILEVER

POST

FRONTCANTILEVER

POST

ADJUST BACKHALF OF GATE


OPEN POSTITION


LATCH POSTNOT SHOWN


BACKHALF

OF GATE


OPEN POSTITION

PG 11 OF 12




STEP 18: MOUNT COLLECTOR ON LATCH POST

STEP 19: MOUNT SAFETY FILLER PLATES ON BOTH CANTILEVER POSTS USING APPROPRIATE TENSION OR BRACE BANDS.

SAFETYFILLERPLATE

48" MINABOVE GRADE.

LATCH POST & CAP

COLLECTOR

U-BOLT

42" TO 48" ABOVE GRADE(TYPICAL)

ROUND LATCH POST

TENSIONBANDS

PER ASTM F2200-02 SPECIFICATIONS,"... ALL OPENINGS SHALL BE DESIGNED, GUARDED OR SCREENED FROM THE BOTTOM OF THE GATE TO A MINIMUM OF 48" ABOVE GRADE TO PREVENT A 2-14" DIAMETER SPHERE FROM PASSING

THROUGH THE OPENINGS ANYWHERE IN THE GATE, AND IN THAT PORTION OF THE ADJACENT FENCE THAT THE GATE COVERS IN

THE OPEN POSITION..."

PG 12 OF 12




MAINTENANCE GUIDELINES

Jamieson gate systems are relatively maintenance free. However, it is suggested that the following be reviewed semi-annually to ensure trouble free

gate operation: o Check attachment, alignment and proper working order of all trucks, brackets

& hardware. o Check vertical alignment of posts. Ensure integrity of the footing and crown. o Check alignment of gate to collector and lower guides Ensure gate is level and

true. o Operate gates in both directions checking for sagging, binding or grinding

noises. Adjust truss cable tension as necessary, but do not over-tighten. o Ensure the enclosed TrusTrac™ is free of debris o Visually inspect truck assemblies to clean dirt/debris and ensure integrity.

Note that the trucks use sealed bearing and require no grease or periodic maintenance.

o Visually check all safety devises (protective guides, safety loops, etc.). Replace or correct as required.

For all automated gates, refer to the manufacturer’s Operator Manual for recommended maintenance and safety practices. For any questions or technical assistance, please contact your nearest Jamieson representative.

1 YEAR LIMITED WARRANTY Jamieson Manufacturing Co. (“Jamieson”) warrants only that its gates will be free from defects in material and workmanship under normal use for a period of one (1) year from date of shipment if, but only if, the gate has been properly installed and operated. Jamieson’s obligation under this warranty is limited to, at Jamieson’s option, the repair or exchange of any part appearing to its satisfaction to be defective in material or workmanship or the refund of the purchase price if Jamieson is unable, by repair or replacement, to make the gate operate in a normal manner under normal use. This limited warranty does not obligate Jamieson to bear any transportation, shipping, removal, installation or other expenses in connection with such gate or the inspection, repair or replacement of any defective parts. To obtain warranty service, purchaser must deliver the gate or defective part to Jamieson’s facility or other point designated by Jamieson. THIS LIMITED WARRANTY IS PURCHASER’S EXCLUSIVE REMEDY. It is extended only to the original purchaser and is non-transferable and non-assignable to any other purchaser or subsequent owner. THIS LIMITED WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, WHETHER WRITTEN, ORAL OR IMPLIED (INCLUDING, WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR USE AND THOSE ARISING FROM COURSE OF PERFORMANCE, DEALING OR USAGE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES OF JAMIESON. JAMIESON NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS GATE. THIS LIMITED WARRANTY SHALL NOT APPLY TO THIS GATE OR ANY PART THEREOF WHICH HAS BEEN SUBJECT TO (1) ACCIDENT, NEGLECT, ALTERATION, ABUSE, MISUSE, OR IMPROPER INSTALLATION, OPERATION OR SERVICE; (2) DAMAGE BY FLOOD, FIRE, OTHER CASUALTY, ACTS OF GOD, RIOTS, INSURRECTIONS, WAR OR TERRORISM; OR (3) USE IN HARSH INDUSTRIAL, COASTAL OR MARINE ENVIRONMENTS. SOME STATES DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. JAMIESON MAKES NO WARRANTY WHATSOEVER IN RESPECT TO ACCESSORIES, COMPONENT PARTS OR ATTACHMENTS NOT MANUFACTURED OR SUPPLIED BY JAMIESON, INCLUDING BUT NOT LIMITED TO, ACCESS CONTROL GATE OPERATORS AND RELATED HYDRAULIC AND ELECTRONIC SYSTEMS. ALL SUCH ITEMS ARE SOLD TO PURCHASER ON AN “AS-IS” BASIS, EXCEPT TO THE EXTENT OF ANY WARRANTY GIVEN TO JAMIESON BY THE ACTUAL MANUFACTURER. THIS LIMITED WARRANTY EXCLUDES ALL COSTS ARISING FROM ROUTINE MAINTENANCE, INCLUDING REPLACEMENT PARTS REQUIRED FOR ROUTINE MAINTENANCE. Jamieson reserves the right to modify, alter or improve its gates, or parts thereof, at any time without incurring any obligation to modify, alter, improve or replace the gate or any parts thereof, previously sold. Jamieson shall not be liable for normal manufacturing defects, customary variations from specifications, or defects arising from designs or other specifications supplied by Purchaser. IT IS UNDERSTOOD AND AGREED THAT JAMIESON’S LIABILITY AND PURCHASER’S SOLE REMEDY, WHETHER IN CONTRACT, UNDER ANY WARRANTY, IN TORT (INCLUDING NEGLIGENCE), IN STRICT LIABILITY OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER, AND UNDER NO CIRCUMSTANCES SHALL JAMIESON BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO, PERSONAL INJURY, PROPERTY DAMAGE, DAMAGE TO OR LOSS OF EQUIPMENT, LOST PROFITS OR REVENUE, AND OTHER ADDITIONAL EXPENSES, EVEN IF JAMIESON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE PRICE STATED FOR THE GATE IS A CONSIDERATION IN LIMITING JAMIESON’S LIABILITY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. JAMIESON WILL NOT BE LIABLE FOR ANY DAMAGES, LOSSES, OR EXPENSES AS A RESULT OF PURCHASER’S NEGLIGENCE, WHETHER DEEMED ACTIVE OR PASSIVE AND WHETHER OR NOT ANY SUCH NEGLIGENCE IS THE SOLE CAUSE OF ANY SUCH DAMAGE, LOSS OR EXPENSE. NO WAIVER, ALTERATION, OR MODIFICATION OF THE FOREGOING CONDITIONS SHALL BE VALID UNLESS MADE IN WRITING AND SIGNED BY AN EXECUTIVE OFFICER OF JAMIESON. THIS WARRANTY SHALL APPLY ONLY WITHIN THE BOUNDARIES OF THE CONTINENTAL UNITED STATES AND CANADA. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. Advice of Jamieson’s technical staff may be available to the trade, but Jamieson, not controlling or supervising the subsequent installation of itsproducts or their use after sale, does not warrant or guarantee such advice. SPECIAL ORDERS: If any material shall be manufactured and/or sold by Jamieson to meet Purchaser’s particular specifications or requirements, Purchaser shall defend, protect, and save harmless Jamieson against all suits at law or in equity and from all damages, claims, and demands for actual or alleged infringement of any United States or foreign patent and shall defend any suit or actions which may be brought against Jamieson for any alleged infringement because of the manufacture and/or sale of the material covered thereby.




JAMIESON HISTORY

(TYP INSIDE BACK COVER)

INSIDE BACK COVER




BRANCH MAP

(TYP BACK COVER)

BACK COVER

Documents

JAMIESON MANUFACTURING CO.€¦ · trustrac™ installation guide did you know? jamieson supplies installation tools. contact your jamieson dealer prior to order for more information