Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
In-Wall Subwoofer Series Owners Manual
IWS-10 IWS-8
18AWG minimum - for distances up to ………………………. . 10 ft
16AWG - from ……………………………………………. 10 to 50 ft
14AWG - from …………………………………………… 50 to 100ft
- Where is the best place to install the speakers- Where do the speakers sound the best- Try to separate the speakers 6 - 10 feet apart.- When placing the speakers in the wall, try to locate them so that the sound is projected towards the general listening area. - If you intend to paint the grilles, try to do so before installation.
Quick installation guide
- Pencil- Drill- Tape Measure
- Wire cutter- Philips-head screwdriver- Sandpaper
Tools needed for installation
STEP 1
Trace along the inclusive template. Cut along the traced line using a drywall saw or rotary drill. A simple, inexpensive drywall saw (about $10 at your local hardware store) is the best choice for beginners. Caution: This is the most important part of the entire installation.If you are not certain whether any obstructions exist behind the desired mounting area, you should start by cutting a small hole in the center of your penciled mounting hole with a drywall saw. Use a piece of sandpaper to sand down the cut out edge for a smoother contour. (See Diagram 1 and Diagram 2)
STEP 2
Run the cable into the cut out location while leaving an extra two feet to make the connection to the speaker easier. Strip back approximately ½” of the speaker cable insulation and twist the copper wires tightly for easy insertion.
On the back of the speaker, press down on the gold-plated compression terminal to reveal the "eye" and insert the speaker cable through the eye for secure connection. Release the compres-sion terminal to lock each cable securely.
Diagram 1:Cutout tracing
Diagram 2:Cut Out
To determine the length and the gauge of speaker wire, you will need to measure the distance between your receiver/amplifier and the speakers.
- Always buy more than you think you would need.- Equal wire lengths should always be used to maintain an equal balance in sound volume.- Sound quality is lost when using thin wire gauge over a long distance.
- Utility knife- Safety eyewear- Gloves
Speaker wire
---------------
- Measure the distance from the receiver/amplifier to the speakers.
---------------------------------
--------------------------------------------------
-----------------
STEP 3
Tighten the dog-ear brackets by simply turning the screws on the
slowly clockwise. The quick-turn mounting system and frame will "sandwich" or clamp around the wall to hold the speaker securely in place. (See Diagram 3)
Diagram 3:Mounting Dog Ear
Closed
Loose
Closed
Loose
...........
..
.
.....
......dog ear
STEP 4
Screw Screw
Tighten the four mounting screws with the same amount of force until the speaker is aligned and held securely to the wall surface. Caution: do not over tighten! (See Diagram 4)
Diagram 4:
Installation
comparable to the speaker’s power handling. Please refer to your owner’smanual for reference.
(See Diagram 7)
Note: Speaker terminals have corresponding (+) and (-) terminals. It is important to connect both speakers in phase. Out of phase will result in thin sound and weak bass. (See Diagram 6)
Diagram 6:Terminal identification
Warranty & Repair
All OSD AUDIO speaker products have (10) year Limited Warranty against defects in materials and workmanship. Proof of purchase must accompany all claims. During the warranty period OSD AUDIO will replace any defective part and correct any defect in workmanship without charge for either parts or labor
are not OSD AUDIO’s responsibility.
For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be performed by OSD AUDIO. The unit must be returned to OSD AUDIO at the owner's expense and with prior written permission. Accidental damage and shipping damage are not considered defects, nor
is damaged resulting from abuse or from servicing performed by an agency or person
OSD AUDIO sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any OSD AUDIO product purchased from an unauthorized dealer or other source, including retailers, mail over dealers and online sellers will not be honored or serviced under existing OSD
AUDIO warranty policy. Any sale of product by an unauthorized source or other manner not authorized by OSD AUDIO shall void the warranty on the applicable product.
Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis of the retail value of the parts and labor. To return for repairs, you must email customer service at [email protected] for a Returned Merchandise Authorization (RMA) number# then the unit must be shipped to OSD AUDIO at the owner's expense, along with a note explaining the nature of service required. Be sure to pack the speaker(s) in a corrugated
container with at least 3 inches of resilient material to protect the unit from damage in transit.
This Warranty Does Not Cover:Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) • • Any product whose
identifying number of decal, serial #, etc. has been altered, defaced or removed • Normal wear and maintenance.
++ + -
Next, individually turn each of the screws (Diagram 5) that operate the dogears counter clockwise a few turns until you feel the dogear is loose from the resting position. Then turn the scew clockwise until you feel the dogear makes contact with the wall surface.
Screw
Screw
Diagram 5:
TIP: Blown-in insulation can some-times work its way into the moving components of the speaker and negatively impacting performance. It is best to replace about a one square foot section directly behind the speaker with rolled-in (bat) insulation.(See Diagram 5)
Subwoofer Amplifier
+
Diagram 7:
-
++Power Handling (25 Watts) Minimum
+ -Note: The speakers wire should be about the same lenght. if
excess wire behind the wall
Speaker Type:
Tweete:
Woofer:
Impedance:
Sensitivity:
Frequency Response:Power Handling:Dimensions: (D x H)
Unit of Measure: Pair Pair Pair
ICE-850
8” Kevlar Ceiling HomeTheater Speakers
Pivoting 1” Aluminum
8” Kevlar Cones
8 Ω
92dB
26Hz - 22kHz175 Watts11 ” x 4 ¼”
9 ”
In Ceiling Model
ICE-810
8” Custom Series Ceiling Speakers
Pivoting 1” Silk Dome
8” Polypropylene
8 Ω
89dB
38Hz - 22kHz140 Watts10 ¾” x 3 ”
9 ”
Contour Switches: 2-Position Front-Mounted ±3dB Bass & Treble Switches
ICE-840
8” High Definition Pro Series Ceiling Speakers
Pivoting 1” Silk Dome
8” Polypropylene
8 Ω
91dB
36Hz - 22kHz175 Watts10 ¾” x 3 ”
9 ”
N/A N/A
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Frequency Response:Power Handling:Dimensions: (D x H)
ICE-670
6 ½” Kevlar LCR CeilingHome Theater Speakers
Pivoting 1” Aluminum
6 ½” Kevlar Cone
8 Ω
92dB 1w/1m
30Hz - 22kHz150 watts9 ¼” x 4 ”8 ¼”
In Ceiling Model
Contour Switches:
N/A
ICE-660
6 ½” High Definition Pro LCR Ceiling Speakers
Pivoting 1” Silk Dome
6 ½” Polypropylene
8 Ω
92dB 1w/1m
50Hz - 22kHz150 watts10 ½” x 5”8 ”
N/A
ICE-650
6 ½” Kevlar Ceiling Home Theater Speakers
Pivoting 1” Aluminum
6 ½” Kevlar Cones
8 Ω
92dB 1w/1m
30Hz - 22kHz150 watts 9 ¼” x 3 ” 8 ”
2-Position Front-Mounted ±3dB Bass & Treble Switches
ICE-640
6 ½” High Definition Pro Series Ceiling Speakers
Pivoting 1” Silk Dome
6 ½” Polypropylene
8 Ω
91dB
38Hz - 22kHz150 watts 9 ½” x 3 3⁄8” 7 ”
N/A
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Frequency Response:Power Handling:Dimensions: (D x H)
6 ½” Custom LCR Series Ceiling Speakers
ICE-630
Pivoting 1” Silk Dome
6 ½” Polypropylene
8 Ω
91dB
52Hz - 22kHz175 Watts10 ½” x 5”8 ”
LCR Ceiling Model
Contour Switches: N/A
Ceiling Cut Out:
Unit of Measure: Pair Pair Pair Ceiling Cut Out:
Unit of Measure: Each Each Each Each Ceiling Cut Out:
ICE-870
8” Kevlar LCR CeilingHome Theater Speakers
Pivoting 1” Aluminum
8” Kevlar Cones
8 Ω
92dB 1w/1m
26Hz - 22kHz175 Watts11 ” x 5 7⁄8”9 ”
2-Position Front-Mounted ±3dB Bass & Treble Switches
ICE-620
6 ½” Custom Series Ceiling Speakers
Pivoting 1” Silk Dome
6 ½” Polypropylene
8 Ω
89dB
58Hz - 22kHz125 Watts9 ½” x 2 ”
7 ¾”
N/A
OSD Audio 775 Columbia Street Brea, CA 92821 | Ph: 888.779.4968 | osdaudio.com
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Frequency Response:Power Handling:Dimensions: (H x W x D)
Unit of Measure: Pair Pair Pair Pair
IW-840
8” High Definition Pro Series In Wall Speakers
Pivoting 1” Silk Dome
8” Polypropylene
8 Ω
90dB
36Hz - 22kHz175 Watts13 ¾” x 10“ x 3 ¾” 8 ¾” x 12 ¾”
In Wall Model
IW-690
6 ½” Kevlar Inwall Home Theater Speakers
Pivoting 1” Aluminum
6 ½” Kevlar Cones
8 Ω
92dB 1w/1m
30Hz - 22kHz150 watts12 ¼” x 8 “ x 3 ”10 ” x 6 ¾”
Contour Switches: 2-Position Front-Mounted ±3dB Bass & Treble Switches
IW-810
8” Custom Series In Wall Speakers
Pivoting 1” Silk Dome
8” Polypropylene
8 Ω
90dB
38Hz - 22kHz150 Watts13 ¾” x 10“ x 3 5⁄8” 12 ¾” x 8 ¾”
N/A
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Frequency Response:Power Handling:Dimensions: (H x W x D)
IW-670
6 ½” Custom Series In Wall Speakers
Pivoting 1” Silk Domeel
6 ½” Polypropylene
8 Ω
87dB
48Hz - 22kHz125 Watts12” x 8 ½” x 3 ”10 ” x 7 5⁄6”
In Wall Model
Contour Switches: N/A
IW-525
IW-680
6 ½” High Definition Pro Series In Wall Speakers
Pivoting 1” Silk Dome
6 ½” Polypropylene
8 Ω
90dB
38Hz - 22kHz150 watts12“ x 8 ” x 3 3⁄8”7 ” x 10 13⁄16”
N/A
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Frequency Response:Power Handling:Dimensions: (H x W x D)
IW-540
5 ¼” High Definition Pro Series In Wall Speaker
Pivoting 1” Silk Dome
5 ¼” Polypropylene
8 Ω
90dB
58Hz - 22kHz100 Watts10 ” x 7“ x 2 ¾”
6 ” x 9 5⁄8”
In Wall Center LCR
Contour Switches:
N/A
IW-550
5 ¼” Kevlar Center ChannelLCR In wall Home Theater Speakers
Pivoting 1” Aluminum
Dual 5 ¼” Kevlar Cones
8 Ω
91dB 1w/1m
30Hz - 22kHz150 watts8” x 15 “ x 3 ”
6 “ x 14 ½”
Wall Cut Out:
Unit of Measure: Pair Pair Pair Pair Wall Cut Out:
Unit of Measure: Each Each Wall Cut Out:
IW-545
IW-850
8” Kevlar Inwall Home Theater Speakers
Pivoting 1” Aluminum
8” Kevlar Cones
8 Ω
92dB 1w/1m
26Hz - 22kHz175 Watts14 ” x 10 “ x 3 ¾”13 “ x 8 ¾”
2-Position Front-Mounted ±3dB Bass & Treble Switches
IW-530
5 ¼” Custom Series In Wall Speakers
Pivoting 1” Silk Dome
5 ¼” Polypropylene
8 Ω
87dB
68Hz - 22kHz100 Watts10 ” x 7 ” x 2 ½”
N/A
9 ” x 6 1⁄8”
5 ¼” High Definition Pro Series Center In Wall LCR Speakers
Pivoting 1” Silk Dome
Dual 5 ¼” Polypropylene
8 Ω
90dB
50Hz - 22kHz125 Watts15 ” x 8 ” 3 ½”13 ” x 6 7⁄8”
N/A
5 ¼” Custom SeriesCenter Channel LCRIn Wall Speakers
Pivoting 1” Silk Dome
Dual 5 ¼” Polypropylene
55Hz - 22kHz100 Watts15 ” x 8 ” 3 ½”13 ” x 6 7⁄8”
8 Ω
90dB
Each
2-Position Front-Mounted ±3dB Bass & Treble Switches
2-Position Front-Mounted ±3dB Bass & Treble Switches
N/A
OSD Audio 775 Columbia Street Brea, CA 92821 | Ph: 888.779.4968 | osdaudio.com
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Frequency Response:Power Handling:Dimensions: (D x H)
Unit of Measure: Pair Pair
ICE-530
5 ¼” Custom Series Ceiling Speakers
¾” Silk Dome Swivel
5 ¼” Polypropylene
8 Ω
88dB
65Hz - 22kHz100 Watts8” x 2 ¾”6 ”
In Ceiling Model
Contour Switches: N/A
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Frequency Response:Power Handling:Mounting Depth:
In Wall Subwoofer
Contour Switches:
IW-S10
10” In Wall Subwoofer
N/A
10 “ Polyproplene Subwoofer
8 Ω
86dB
38Hz - 200Hz +/- 3dB25-200 watts3 ¾”10 “ x 10 ”
Ceiling Cut Out:
Unit of Measure: Each Each Wall Cut Out:
IW-S8
ICE-540
5 ¼” High Definition Pro Series Ceiling Speakers
¾” Silk Dome
5 ¼” Polypropylene
8 Ω
90dB
58Hz - 22kHz175 Watts7 ¾” x 2 ¾”6 ”
N/A
8” In Wall Subwoofer
N/A
8” Polypropylene
8 Ω
87dB
40Hz - 200Hz +/- 3dB25-150 Watts3 “ 8 ¾” x 8 ¾ ”
N/A
N/A
Speaker Type:
Tweeter:
Woofer:
Impedance:
Sensitivity:
Frequency Response:Power Handling:Dimensions:(D x H)
Unit of Measure: Each Each Each
ICE-640TT
6 ½” High Definition Pro Series Ceiling Speakers
Dual ¾” Silk Dome
6 ½” Polypropylene
8 Ω
86/89dB
40Hz - 22kHz150 Watts9 ½” x 3 7 ”
Dual Tweeter Ceiling Speakers
Contour Switches: N/A
ICE-620TT
6 ½” Custom Series Stereo Speakers
Dual ¾” Silk Dome
6 ½” Polypropylene
8 Ω
86/89dB
40Hz - 22kHz125 Watts 9 ½” x 3 ” 7 ¾”
N/A
Ceiling Cut Out:
ICE-840TT
8” High Definition Pro Series Ceiling Speakers
Dual ¾” Silk Dome
8” Polypropylene
8 Ω
86/89dB
36Hz - 22kHz175 Watts11 ¾” x 3 ”9 ”
N/A
OSD Audio 775 Columbia Street Brea, CA 92821 | Ph: 888.779.4968 | osdaudio.com