Issc m22 Manual

7/17/2019 Issc m22 Manual

http://slidepdf.com/reader/full/issc-m22-manual 1/24

Handling and Safety Instructions

ISSC M22SEMI AUTOMATIC

PISTOLCALIBER .22 LR



It should be remembered that even the safest gun is potentially

dangerous to you and others when it is not properly handled.

Always bear in mind:

- Keep your nger away from the trigger unless you really intend to re.

- Always keep your weapon pointing in a safe directionso that you and others cannot be endangered.

- First of all read and understand the operating instructions

and learn how the weapon works and is to be handled.

- Always treat an unloaded weapon as if it were loaded.

Important instructions for the use of rearms



Description: Section Page

Product description D-01 03Safety regulations D-01-1 04

Technical data D-01-2 05

Safety mechanisms D-02 06

Transporting the pistol D-03 07

Handling the gun D-04 07

General D-04-1 07

Ammunition D-04-2 07

Loading the magazine D-04-3 08

Inspections before use D-04-4 09

Inspections after use D-04-5 09

Loading the pistol D-04-6 10Firing D-04-7 11

Decocking the hammer D-04-8 11

Pistol with empty magazine D-04-9 11

Unloading your pistol D-04-10 12

Disassembly and reassembly of the pistol D-04-11 12

Sights D-05 13

Cleaning D-06 14

Care of the gun D-07 14

Safekeeping and storage of gun D-07-01 15

Shipping the gun to ISSC D-07-02 15

Warranty for ISSC weapons D-07-03 15Disposal D-07-04 16

Accessories D-07-05 16

Ammunition Warnings D-07-06 16

Correct position of the main spring D-08 17

Disassembly of the compensator D-08-01 17

Removing the SD screw D-08-02 17

State by State warnings D-09 18-19

Explosion drawings / spare parts list D-10 20-21





D-01: Product Description:

Dear valued customer,

Congratulations on your purchase of the ISSC M22 pistol.

In order to create your personal gun, please ask your dealer for the available

line of accessories.

Manufacturer contact:ISSC Handels GmbH

Hannesgrub 3

AT-4910 Ried im Innkreis

Austria

page 03ISSC AUSTRIA - M22



page 04

D-01-1: General instructions / Safety regulations

Never use the gun under the influence of drugs or alcohol, while ill or suffering other such difficulties.These conditions can impair your powers of judgement and reflexes.

Always think the gun as being loaded and with the safety off until you have establishedthe opposite through the unloading procedure.

Always keep the muzzle of the gun in a safe direction with all handling. A safe direction is towards an areawhere there are no people, other life forms or property that is not a recognized target.

Never point the gun at doors, panes of glass, walls, concrete, stone or flat surfaces (water included). A bullet can penetrate such surfaces or be ricocheted in an unsafe direction.

Never aim at yourself or other life forms.

Never rely on safety mechanisms alone. Safety mechanisms are not a substitute for careful, correct andsecure handling of the gun.

Always treat your gun as if the safety mechanisms were not functioning. The best safety precaution is a correct,well-trained and safe handling of the gun.

Never shoot with a gun which has been penetrated by water, sand, dirt or other foreign bodies.

Never decock the hammer by holding on to the hammer and pulling the trigger at the same time.

Never let a loaded gun out of your hand.

Always unload the gun immediately after firing, before putting the gun away, putting into a holster or handing toanother authorized person.

Never give the gun to a person who has not thoroughly familarized himself or herself with the safety instructionsand handling of gun, by reading the corresponding instructions.

Never leave the gun lying unattended and protect the gun from unauthorized access.

Never store the gun loaded, but rather remove the magazine and ensure that no cartridge is left in thechamber of the barrel.

Always keep the gun and the ammunition seperate from one another, and ensure that neither is obtained byunauthorized persons or children.

ISSC AUSTRIA - M22



page 05

D-01-2: Technical Data:

Included in the standard

delivery are:

1 x pistol

1 x magazine

1 x handbook

1 x hardcase

1 x screwdriver

1 x child lock key

Caliber 22 Long Rifle HV

Action SA (single action)

Overall length 181 - 217 mm / 7,12 - 8,54 inch

Overall height 127 mm / 5 inch

Overall width 27,5 mm / 1,08 inchBarrel length 104 - 140 mm / 4,09 - 5,51 inch

Sight length 141 - 177 mm / 5,55 - 6,96 inch

Weight without magazine 605 g / 1,33 lbs

Magazine weight empty 75 g / 0,16 lbs

Trigger weight, approx. 2,0 kg / 4,4 lbs

Magazine capacity / rounds 10 rds

ISSC AUSTRIA - M22



page 06

D-02: Operation of the safeties (safety devices):

1. Manual safety/Decocker

To engage the safety, turn the safety

lever, as shown in fig.1, to the lower

position. Hammer gets decocked.

CAUTION: Always keep the manual safety

engaged until you intend to fire the gun.

2. Trigger lockThe enclosed key is used to lock the trigger mechanism of the M22.

Without the key it is impossible to disengage the safety. fig.3 safe and fig.4 fire.

Use this feature to prevent unauthorized persons from using your weapon.

3. Drop safety (automatic internal safety)

The drop safety (firing pin safety) is only disengaged when the trigger is pulled.

If,after a fall, the hammer was released, then the firing pin would not be activated.

CAUTION:

All safety devices of the weapon are mechanical safeties, and the shooter is the

only one who can engage and disengage these safeties.

NEVER RELY SOLELY ON MECHANICAL SAFETIES - always be extremely

careful and avoid situations which could lead to an accident.

fig.1 fig.2 fig.3 safety engaged

fig.4 ready to fire

ISSC AUSTRIA - M22



page 07

4. Magazine safety

Without the magazine inserted, the magazine safety of the M22 prevents a round to be fired. A cartridge in thechamber cannot be ignited.Always inspect the chamber of your pistol after the magazine has been removed from the

gun. Make sure that no cartridge is left in the chamber after the safety has been engaged.

5. Loaded chamber indicator

A small slot in the upper part of the slide allows for an

inspection of the chamber to see if a cartridge has been loaded (fig. 5).

D-03: Transporting the pistol:For your own safety and the safety of others, always transport the gun

unloaded and decocked. Never carry a gun with you that has already

been cocked and which has a round in the chamber.

Transport the gun seperate from the ammunition.

Ensure that all applicable laws governing the transport of firearms are complied with.

D-04: Handling the gun:

D-04-1: General:

The gun is generally delivered preserved with a thin, protective grease and oil coating.

D-04-2: Ammunition:

For your gun, use only commercial grade ammunition in its original packing which

correponds with the caliber of the gun. The correct caliber is imprinted on the gun.

Never use reloaded, „refurbished“, hand-loaded, non standard ammunition of a different caliber.

fig.5

ISSC AUSTRIA - M22



page 08

D-04-3: Loading the Magazine:

Procedure:

1. Put the cartridge on the feeder, near the magazine feed lips.

2. Pull down the spring of the magazine.

3. Push the bullet to the backside of the magazine.

4. Load only the quantity of bullets into the magazine, you want to fire. (max. 10 bullets)

Notice:

Use the side-mounted button to press the follower down

and insert a cartridge under the magazine lips (fig. 7).

Do not use force.

Damaged magazine lips will cause malfunctions

and will render the weapon useless.

Tap the back of the loaded magazine against

the palm of your hand.

Properly positioned cartridges inside the magazine

help to prevent stoppages.When a magazine is to be emptied,

remove the cartridges one after the other

by pushing them to the front side of the magazine.

fig.7

ISSC AUSTRIA - M22



page 09

D-04-4: Inspections before use

Notice:

Make sure that the pistol is unloaded (chamber cleared, barrel clear of any obstructions, magazine empty)

for inspection and that the safety is engaged.

Functional inspection

1. Remove the magazine, retract the slide. After the slide has been released,

the mainspring must press the slide fully forward.

2. Insert the empty magazine, retract the slide. The slide must be caught in its rearmost position.

3. Remove the magazine, slightly retract the slide. After the slide has been released,

the mainspring must press the slide fully forward.

4. To decock the gun, press the decocker.

5. Insert the empty magazine, fully retract the slide. The slide must be caught in its rearmost position.

6. Press down the slide stop. The mainspring must press the slide fully forward.

7. Remove the magazine, pull the trigger. The hammer must not fall.

D-04-5: Inspections after use

Notice:

Make sure that the pistol is unloaded (chamber cleared, barrel clear of any obstructions, magazine empty)

for inspection and that the safety is engaged.

Proceed with the functional inspection described under D-04-4.

ISSC AUSTRIA - M22



page 10

D-04-6: Loading the pistol

CAUTION: Read and understand the operating instructions thoroughly before youload your gun. Malfunction may occur when ammunition with low propellant charge is fired.

Engage safety.

Press magazine catch and remove empty magazine (fig. 6).

Use the side-mounted button to press the follower down and

insert a cartridge under the magazine lips (fig. 7). Do not use force.

Damaged magazine lips will cause malfunctions and will render

the weapon useless.

Tap the back of the loaded magazine against the palm of your hand.

Properly positioned cartridges inside the magazine help to prevent

stoppages. When a magazine is to be emptied, remove the cartridges

one after the other by pushing them to the front side of the magazine.

Push the loaded magazine into the magazine well until the magazine

catch locks it (fig. 8).

Loading the chamber with the first cartridge

Pick up the gun with your shooting hand, hold it at an angle of approx.

45 degrees and point the muzzle in a safe direction. Use other handto retract slide. Release slide. The slide travels forward and inserts

the first round into the chamber. The hammer is now cocked and ready to fire.

CAUTION! Your gun is now ready to fire. Regard safety instructions, keep shooting

finger away from trigger until you really intend to fire.

If you do not fire your gun immediately after loading it, decock hammer.

fig.7fig.6

fig.8

ISSC AUSTRIA - M22



page 11

D-04-7: Firing:

The pistol is only single action. To fire it „single action“ means that the gun is loaded and that the hammer is

manually cocked before firing. The trigger pull is 0.14 inch of travel and 4 pound of force.

The action of the slide then automatically reloads the pistol and cocks the hammer.

D-04-8: Decocking the hammer:

Point the muzzle in a safe direction. Put this before the first mention of “decock the hammer”. Press the decocker.

D-04-9: Pistol with empty magazine:

After the last round was fired, the slide stop holds the slide in its opened position.

Engage the safety. In case you intend to commence shooting,

replace empty magazine by a full one.

Press the slide stop lever (fig. 9), the slide will travel

forward and load the chamber with the first round.

Keep your weapon in your shooting hand and keep itpointing in a safe direction so that there is no danger for other persons.

If shooting is not to commence, engage safety and

decock hammer. Remove magazine and inspect the

chamber, it must be clear. Close breech.fig.9

ISSC AUSTRIA - M22



D-04-10: Unloading your pistol

Engage safety. Remove magazine and retract slide.

The round in the chamber is extracted and ejected.

Make a visual inspection of the barrel - it must be clear! fig. 10

Allow slide to travel forward and decock hammer.

D-04-11: Disassembly and reassembly of the pistol

It is not necessary to strip the pistol any further as is described in this manual.

Further disassembly, improper assembly and disregard of the instructions

will lead to loss of warranty, and under no circumstances will the manufacturer

then be liable for damages to persons or property.

To do so, engage the safety, remove the magazine and

inspect the weapon, it must be unloaded.

Press the takedown lever down (on both sides) fig. 11(1).

Fully retract the slide, lift its rear sectionand push forward off the receiver fig. 11(2).

Assembly of the gun is in reverse order

page 12

fig.10

1

2

fig.11

ISSC AUSTRIA - M22



page 13

D-05: Sights

Attention: If you remove the front sight it will be destroyed!

Elevation adjustment:

Elevation adjustment can be changed by mounting front

sights of different height. If your weapon fires too low, a lower

front sight is to be mounted, if it fires too high, a higher front sight is to be mounted.

To change the front sight, use a screwdriver to press it out of its seat on the slide.

Attention: If you remove the front sight it will be destroyed!

The rear sight is adjustable for windage.

Windage adjustment

Turn screw on the sight to the right if weapon fires to the right;

turn it to the left if weapon fires to the left. fig. 12

fig.12

ISSC AUSTRIA - M22



page 14

D-06: Cleaning:

The previous dissassembly instruction is sufficient for cleaning. A further disassembling of the pistol should only to be made by qualified personnel.

Do not use a steel brush or any other hard material to clean the barrel. This could damage the flat surface of the

barrel. Use only a suitable cleaning rod and brushes of the right caliber.

Thinner could damage the surface of the pistol. Before using any cleaner or thinner please note the Advice of the

manufacturer.

Procedure:

1. Lubricate the cleaning brush with gun oil and insert it into the barrel via the chamber. Use the brush to carefully

remove all powder residues and dirt in the barrel and chamber.2. Wipe powder residues and oil from the barrel bore and chamber with cleaning patches.

3. Remove dirt from guides of breech and breech-block with a brush or a cleaning patch and than wipe down with a

cloth impregnated with gun oil or gun grease.

4. Oil the chamber lightly.

D-07: Care of the gun:

Always keep your gun in immaculate condition and in good working order.

Always clean your gun after use.

Never modify or repair parts of your gun yourself.

Have your gun checked once every 12 months by a qualified gunsmith or armourer because defects, wear,

corrosion, etc. are not always visible from the outside.

For repairs or service work, however, we recommend that you return the gun to your dealer / importer who always

holds a full range of replacement parts in stock.

If you order spare parts without returning the gun, you are responsible for ordering the correct part and its correct

fitting by a qualified gunmaker or armourer.

ISSC AUSTRIA - M22



D-07-1: Safekeeping and storage of the gun:

Always store your gun unloaded and in cleaned condition.

Store your gun separately from its ammunition and under lock and key.

The gun and ammunition must not be accessible to children and other inexperienced or unauthorized persons.

D-07-2: Shipping the gun to ISSC:

Important notice:

CAUTION! A weapon which fails to function properly is dangerous. It should be safely kept in a way that prevents itsuse before it is repaired. It is difficult to repair a weapon, and improper assembly can lead to dangerous malfunctions.

Only let an authorized and qualified gunsmith inspect and repair your weapon!

The ISSC website has instructions for returning a gun for service.

ISSC will not accept any gun without prior authorization.

D-07-3: Warranty for ISSC-weapons:

This gun is warranted to be free from defects in material and workmanship. Any such defects of which we receive

written notice within one year from date of original purchase will be remedied without charge within a reasonable time

after such notification and delivery of the handgun. For reporting warranty issues, shipping information and any other

repair or service issues, please refer to the customer service information

on the www.austriansportingarms.com website.

page 15ISSC AUSTRIA - M22



page 16

D-07-4: Disposal:

Strictly observe any current national legislation governing the disposal of handguns.

When shipping the gun, strictly observe the instructions listed under Sect. D-07-2

D-07-5: Accessories: ( find it under: www.issc-austria.com)

Essential information when ordering accessories or spare parts from your dealer/service department in your country.

Gun Model (caliber, designation) Gun serial number

Item number and index

D-07-6: AMMUNITION WARNINGS:

The M22 pistol is chambered only for the .22 caliber Long Rifle cartridge, standard or high velocity, manufactured to

U.S industry standards. Do not attempt to load .22 Long, .22 Short, or any other type .22caliber cartridge into the ma-

gazine or into the chamber, even if the cartridge appears to load properly

WE SPECIFICALLY DISCLAIM RESPONSIBILITY FOR ANY DAMAGE OR INJURY WHATSOEVER OCCURING

IN CONNECTION WITH, OR AS THE RESULT OF, THE USE IN M22 PISTOLS OF FAULTY. OR NONSTANDART,

OR ‘REMANUFACTURED’ OR HANDLOADED (RELOADED) OR OF CARTRIDGES OTHER THAN THOSE

FOR WHICH THIS FIREARMS IS CHAMBERED.

ISSC AUSTRIA - M22



page 17

D-08: Correct position of the main spring:

To ensure a correct function of the weapon, the main spring

has to mounted in the correct position. Make sure that the

small diameter (14) is in front of the chamber. Fig.13.

Especially if the weapon has been disassembled and reassembled

it is important to check the correct positioning of the main spring.

D-08-01: Disassemble the compensator:

To dissassemble the compensator of the target version

take out the compensator screw using a allen key size 2mm

and turning it counterclockwise. After the screw has been taken out

you can pull off the compensator of the weapon to the front. fig.14.

D-08-02: Removing the SD screw:

To mount a silencer on the SD version of the M22 you have to

screw off the SD nut in front of the barrel. Use the included SD key

to disassemble the SD nut by by turning it counterclockwise.

To assemble the SD nud screw it on the barrel

by turning it clockwise. fig.15.

fig.13

fig.14

fig.15

ISSC AUSTRIA - M22



page 18

D-09: STATE-BY-STATE Safety Warnings:

Certain states require by law that their own specified warnings be included by the manufacture, distributor, or retail with firearms sold inthat state. Austrian Sporting Arms sells its products in compliance with applicable laws and regulations. Because our products may be

sold in these states, we include the following:

California:

WARNING: “Children are attracted to and can operate firearms that can cause severe injuries or death. Prevent child access by always

keeping guns locked away and unloaded when not in use. If you keep a loaded firearm where a child obtains and improperly uses it,

you may be fines or sent to prison”.

Advertencia:

“A los ninos los atraen las armas de fuego y las pueden hacer funcionar. Ellos pueden causares lesions graves y la muerte. Evite que

los ninos tengan accesso a las armas de fuego guardandolas siepmre con llave y descargadas cuando no las este utilizando. Si usted

tiene un arma de fuego cargada en un lugar en que un nino tiene acceso a ella y use indebidamente, le pueden dar una multa o enviar-

lo a la carcel”.

Connecticut:

“UNLAWFUL STORAGE OF A LOADED FIREARM MAY RESULT IN IMPRISONMENT OR FINE”.

Florida:

“IT IS UNLAWFUL, AND PUNISHABLE BY IMPRISONMENT AND FINDE, FOR ANY ADULT TO STORE OR LEAVE A FIREARM IN

ANY PLACE WITHIN THE REACH EASY ACCESS OF A MINOR UNDER 18 YEARS OF AGE OR TO KNWINGLY SELL OR OTHER-

WISE TRANSFER OWNERSHIP OR POSSESSION OF A FIREARM TO A MINOR OR A PERSON OF UNSOUND MIND”.

Maine:

“ENDANGERING THE WELFARE OF A CHILD IS A CRIME. IF YOU LEAVE A FIREARM AND AMMUNITION WITHIN EASY ACCESS

OF A CHILD, YOU MAY BE SUBJECT TO FINE, IMPRISONMENT OR BOTH. KEEP FIREARMS AND AMMUNITION LOCKED UP.

USE TRIGGER LOCKS”.

Maryland:

WARNING: “Children can operate firearms which may cause death or serious injury. It is a crime to store or leave a loaded firearm in

any location where an individual knew or should have known that an unsupervised minor would gain access to the firearm. Store your

firearm responsibly”.

ISSC AUSTRIA - M22



page 19

D-09: STATE-BY-STATE Safety Warnings:

Massachusetts:“WARNING FROM THE MASSACHUSETTS ATTORNEY GENERAL: This handgun is not equipped with a device that fully blocks use

by unauthorized users. More than 200.000 firearms like this one are stolen from their owners every year in the United States. In additi-

on, there are more than a thousand suicides each year by younger children and teenagers who get access to firearms. Hundreds more

die from accidental discharge. It is likely that many more children sustain serous wounds, or inflict such wounds accidentally on others.

In order to limit the chance of such misuse, it is imperative that you keep this weapon locked in a secure place and take reasonable

preventive steps may result in innocent lives being lost, and in some circumstances may result in your liability for these deaths.

“IT IS UNLAWFUL TO STORE OR KEEP A FIREARM, RIFLE, SHOTGUN OR MACHINE GUN IN ANY PLACE UNLESS THAT WEA-

PON IS EQUIPPED WITH A TAMPER RESIST SAFETY DEVICE OR IS STORED OR KEPT IN A SECURELY LOCKED CONTAINER.”

New Jersey:

“IT IS A CRIMINAL OFFENSE TO LEAVE A LOADED FIREARM WITHIN EASY ACCESS OF A MINOR.”

New York City:

“THE USE OF A LACKING DEVICE OR SAFETY LOCK IS ONLY ONE ASPECT OF RESPONSIBLE FIREAMS STORAGE. FOR

INCREADES SAFETY, FIREARMS SHOULD BE STORED UNLOADED AND LOCKED IN A LOCATION THAT IS BOTH SEPARATE

FROM THEIR AMMUNITION AND INACCESSIBLE TO CHILDREN AND OTHERT UNAUTHORIZED PERSONS.”

North Carolina:

“IT IS UNLAWFUL TO STORE OR LEAVE A FIREARM THAT CAN BE DISCHARGED IN A MANNER THAT A REASONABLE PERSON

SHOULD KNOW IS ACCESSIBLE TO A MINOR.”

Texas:“IT IS UNLAWFUL TO STORE, TRANSPORT, OR ABANDON AN UNSECURED FIREARM IN A PLACE WHERE CHILDREN ARE

LIKELY TO BE AND CAN OBTAIN ACCES TO THE FIREARM.”

Wisconsin:

“IF YOU LAVE A LOADED FIREARM WITHIN THE REACH OR EASY ACCESS OF A CHILD YOU MAY BE FINED OR IMPRISONED

OR BOTH IF THE CHILD IMPROPERLY DISCHARGES, POSSESSES, OR EXHIBITS THE FIREARM.”

ISSC AUSTRIA - M22



page 20

D-10: Explosion drawing / spare parts M22:

ISSC AUSTRIA - M22



page 21

D-10: Explosion drawing / spare parts M22:

Pos. Description1 Barrel with bracket2 Slide

3 Takedown lever

4 Takedown block

5 Trigger

6 Magazine

7 Feeder

8 Butt plate

9 Grip

10 Receiver

11 Magazine catch

12 Butt plate holder

13 Magazine safety

14 Extractor

15 Trigger bar 16 Ejector with slide stop

17 Release lever

19 Slide block

20 Firing pin

21 Trigger safety

22 Drop safety

23 Trigger lock

24 Drop safety lever

25 Safety lever

26 Safety roll

27 Hammer catch

28 Hammer

31 Front sight 4,6

34 Magazine button

35 Distance bushing36 Rear sight housing

37 Rear sight

38 Rear sight screw

39 Washer

40 Slide spring

41 Magazine spring

Pos. Description42 Spring43 Hammer spring

44 Trigger spring

45 Leg spring

46 Magazine catch spring

47 Leg spring

48 Bracket bushing

55 Pressure spring

56 Pressure spring D-009

57 Pressure spring D-042B

58 Pressure spring D-011H

59 Pressure spring D-0,26A

60 Pressure spring D-0,39

65 Groove pin ISO 8741 1,5x12

66 Pin DIN 6325 - 1,5m6x1667 Pin DIN 6325 - 2m6x10 BR

68 Pin DIN 6325 - 2m6x16

69 Pin 2m6x18

70 Pin DIN 6325 - 3m6x10

71 Pin DIN 6325 - 3m6x24

72 Pin 5m6x18

73 Pin DIN 6325 - 4m6x26

74 Spiral pin ISO 8750 2,5x22

75 Screw

76 Screw DIN 965 AM3x16

77 Pin 3m6x18

78 Threated Pin ISO 27436 M2,5x5

79 Groove pin DIN 1472 2x12

80 Ball DIN 5401 2,381mm

ISSC AUSTRIA - M22



It should be remembered that even the safest gun is potentially

dangerous to you and others when it is not properly handled.

Always bear in mind:

- Keep your nger away from the trigger unless you really intend to re.

- Always keep your weapon pointing in a safe direction

so that you and others cannot be endangered.

- First of all read and understand the operating instructions

and learn how the weapon works and is to be handled.

- Always treat an unloaded weapon as if it were loaded.

Important instructions for the use of rearms



Manufacturer:ISSC Handels GmbH

Hannesgrub 3

4910 Ried im Innkreis

Austria

www.issc.at

[email protected]

phone: +43 (0) 7752 - 212 - 70fax: +43 (0) 7752 - 212 - 71

CopyrightESC

-Id.No.0 0

0012date05/12



Documents

Issc m22 Manual