Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
Disclosure to Promote the Right To Information
Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public.
इंटरनेट मानक
“!ान $ एक न' भारत का +नम-ण”Satyanarayan Gangaram Pitroda
“Invent a New India Using Knowledge”
“प0रा1 को छोड न' 5 तरफ”Jawaharlal Nehru
“Step Out From the Old to the New”
“जान1 का अ+धकार, जी1 का अ+धकार”Mazdoor Kisan Shakti Sangathan
“The Right to Information, The Right to Live”
“!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता है”Bhartṛhari—Nītiśatakam
“Knowledge is such a treasure which cannot be stolen”
“Invent a New India Using Knowledge”
है”ह”ह
IS 15314 (2003): Method of Tests for Tightness and Balanceof Stitches on Seam Sewn by Industrial Sewing Machines [MED29: Sewing Machines]
IS 15314:2003
Indian Standard
METHOD OF TESTS FOR TIGHTNESS ANDBALANCE OF STITCHES ON SEAM SEWN BY
INDUSTRIAL SEWING MACHINES
ICS 61.080
@ BIS 2003
BUREAU OF IN DIAN STANDARDSMANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
March 2003 Price Group 1
Sewing Machines Sectional Committee, ME 29
FOREWORD
This Indian Standard was adopted by the Bureau of Indian Standards, after the draft finalized by the”SewingMachines Sectional Committee had been approved by the Mechanical Engineering Division Council.
The standard specifies the method of tests for tightness and balance of stitches on the materials sewn by singleneedle straight lock stitch industrial sewing machines.
This standard is one of the series of standards prepared to rationalize the method of tests for industrial sewingmachine and specifies the procedure for measuring vibrations generated by single needle straight lock stitchindustrial sewing machines and over edge industrial sewing machines as a vibration level and vibrationdisplacements of industrial sewing machines.
“Other standards in this series are:
1S 15312:2002 Method of tests for seam puckering on materials sewn by industrial sewing machines
IS 15313:2002 Method of test for vibration measurement for industrial sewing machines
In preparation of this standard, assistance has been derived from the following standard issued by the JapaneseIndustrial Standard Committee:
JISB 9055:1986 Testing methods for seam purchasing on material sewn by industrial sewing machines
In reporting the results of a test or analysis made in accordance with this standard, if the final value, observedor calculated, is to be rounded off, it shall be done in accordance with IS 2: 1960 ‘Rules for rounding offnumerical values (revised)’.
IS 15314:2003
Indian Standard
METHOD OF TESTS FOR TIGHTNESS ANDBALANCE OF STITCHES ON SEAM SEWN BY
INDUSTRIAL SEWING MACHINES1 SCOPE
This standard specifies the method of tests fortightness and balance of stitches on seam sewn bystraight lock stitch industrial sewing machines(hereafter referred to as the sewing machine).
2 DEFINITIONS
For the purpose of this standard the followingdefinitions shall apply.
2.1 Sewing Machine
The sewing machine means unit set with a sewingmachine head, base/table, legs and drivingarrangement.
2.2 Tightness and Balance of Stitches
The leno state of sewing threads constituting stitchesand the state of tightness and balance of sewing threadsto the sewn materials. This is expressed by the ratio ofsewing threads lengths and rates of tightness andbalances of needle thread and of bobbin thread as wellas of cloth.
2.3 Incidental Looping
The part of knot state of needle thread appearing onthe back surface of sewn matter at the seam.
2.4 Looping
The part of loop state of needle thread appeared on theback surface of sewn matter at the seam.
2.5 Skip Stitch
The condition where a part of stitch is not formed atthe seam.
3 TEST PROCEDURE
3.1 Preparation of Test Piece
Make the size of test specimen 100 mm in width,300 mm in length as shown in Fig. 1 and make one set
by overlapping the required number of sheets.
3.2 Test Method
By taking into consideration the sewing workconditions of following each item, prepare three rowsof seams along the sewn portion of Fig. 1 for the testpiece:
SEWN PORTION
4——t——
.+-- —--+- .- tt 100——
-.— .--— --- —-- +——t
a)
b)
c)
Alldimensions in millimetres,
FIG.1 TEST PIECE
The installation of sewing machine is so stabi-lized that the vibration does not give inter-ference to sewing.The running of sewing machine is to be soperformed as to become the specified numberof revolution quickly from the stopping condi-tion.The test piece is to be so made that excess forceis not.added from the outside and, sewn fromits front end up to rear end.
3.3 Method of Measurements
3.3;1 Measurement of Thickness of Test Piece
Measure the thickness (mm) of test pieces of one setspecified in 3.1 at five portions; and obtain the averagevalue (to two places of decimals).
3.3.2 Measurement of Needle Thread Length andBobbin Thread Length
a) Place a test piece after sewing as described in3.2 on a flat stand, under natural condition asit is in the sampling section shown in Fig. 1,mark at interval of 50 mm on each row so asnot to come on needle hole, thereafter cut thepart and prepare the sample of three piecesshown in Fig. 2.
IS 15314:2003
SLAM 20 Approx.
i ———— ———-
b)c)
d)
Alldimensions in millimetres.
FIG.2 SAMPLE
At the time the seam is to be free from inciden-tal looping, looping skip stitch, etc.Count the number of stitch in the sample.In order to make loosening of thread easy, cutdown near the sewn portion of sample withtaking care so as not to damage the sewingthread, and take out the needle thread andbobbin thread from the sample without apply-ing undue force.Press lightly the needle thread and bobbinthread in such degree that the thread is notelongated and becomes straight and measuretheir lengths (mm) by using a scale of accuracyof 1 mm.
3.4 Method of Calculation
3.4.1 The ratio of sewing thread lengths shall becalculated accord]ng to the following formula and theaverage of three pieces of sample shall be obtained (tothe integer place):
~=~xlm
I!&
where
a = ratio of sewing thread lengths (70);
L, = length of needle thread, mm; and
Lb = length of bobbin thread, mm.
3.4.2 Tightness rates of needle thread, bobbin threadand cloth shall “be calculated according to thefollowing formulae and the average value of threepieces of sample, be obtained (to the integer place):
where
s ——
N=
T=
B. =p, =
B. =
sewing length, mm;
number of stitches;
thickness of test piece of one set, mm;
tightness rate of needle thread (%);
tightness rate of bobbin thread (Ye); and
tightness rate of cloth (%).
4 RECORD OF TEST RESULTS
For test results of tightness .of stitches, (a) to (d) shallbe recorded and, as required, (e) be recorded.
a)
b)c)d)
e)
Tightness of stitches:i) Ratio of sewing thread lengths,
ii) Tightness rate of needle thread and bob-bin thread, and
iii) Tightness rate of cloth.Date of testClass and type of sewing machine used for testMaterials:
i) Classification of material used for testpiece (as required, the sample is to beappended); and
ii) Classification of sewing thread.Test conditions:
i)
ii)
iii)
iv)
v)vi)
vii)
viii)ix)
Overlapping method of test pieces (sur-face, back face, directions and numberof sheets);Average value of numbers of needles ofthree pieces of sample;Number of revolutions of sewingmachine;Thread tensile force of needle thread andbobbin thread, T (see Note 1);Check spring tension, F (see Note 2);Class of needle and number of needle(thickness number of needle stem);Dimensions of needle hole of throatplate;Class of presser foot; andPresser foot force, kg.
1 The thread tensile force means the tensile force to rake outupward the threadby hanging on thread guard bend bar from thestitch balancing thread tension dish at the stopping time ofsewing machine. The thread tensile force of bobbin threadmeans the tensile force to take out upward in this inclination thethread from needle hole of throat plate at the stopping time ofsewing machine.
Further, in order to make the bobbin thread not to contact therotating hook, measure under the condition where the needle baris at nearly upper dead point.
2 The check spring tension means the tensile force whenhanging the needle thread on check spring and thread guard bendbar, and pulling upward and then the check spring begins thedisplacement.
2
Bureau of Indian Standards
BIS is a statutory institution established under the Burcw of Zndian Standards Act, 1986 to promote
harmonious development of the activities of standardization, marking and quality certification of goodsand attending to connected matters in the country.
Copyright
BIS has the copyright of all its publications. No part of these publications may be reproduced .in any formwithout the prior permission in writing of BIS. This does not preclude the free use, in the course ofimplementing the standard, of necessary details, such as symbols and sizes, type or grade designations.
Enquiries relating to copyright be addressed to the Director (Publications), BIS.
Review of Indian Standards
Amendments are issued to standards as the need arises on the basis of comments. Standards are also reviewed
periodically; a standard along with amendments is reaffirmed when such review indicates that no changes areneeded; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standardsshould ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of‘BIS Catalogue’ and ‘Standards: Monthly Additions’.
This Indian Standard has been developed from Doc : No. ME 29A-M 18( 0438).
Amendments Issued Since Publication
Amend No. Date of Issue Text Affected
BUREAU OF INDIAN STANDARDS
Headquarters :
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002 Telegrams : Manaksanstha
Telephones :23230131,23233375,2323 9402 (Common to all offices)
Regional Offices : Telephone
Central : Manak Bhavan, 9 Bahadur Shah Zafar Marg
{
23237617NEW DELHI 110002 23233841
Eastern : 1/14 C.I.T. Scheme VII M, V. L P. Road, Kankurgachi
{
23378499,23378561
KOLKATA 700054 23378626,23379120
Northern : SCO 335-336, Sector 34-A, CHANDIGARH 160022 j_60 3843
Southern
Western
Branches :
~60 9285
: C.I.T. Campus, IV .Cross Road, CHENNAI 600113
{
22541216,2254144222542519,22542315
: Manakalaya, E9 MIDC, Marol, Andheri (East)
{
28329295,28327858MUMBAI 400093 28327891,28327892
AHMEDABAD. BANGALORE. BHOPAL. BHUBANESHWAR. COIMBATORE. FARIDABAD.
GHAZIABAD. GUWAHATI. HYDERABAD. JAIPUR. KANPUR. LUCKNOW. NAGPUR.NALAGARH. PATNA. PUNE. RAJKOT. THIRUVANANTHAPURAM. VISAKHA-PATNAM.
Printed at 14abhat Offset Press, New Delhi-2