Disclosure to Promote the Right To Information

Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public.

इंटरनेट मानक

“!ान $ एक न' भारत का +नम-ण”Satyanarayan Gangaram Pitroda

“Invent a New India Using Knowledge”

“प0रा1 को छोड न' 5 तरफ”Jawaharlal Nehru

“Step Out From the Old to the New”

“जान1 का अ+धकार, जी1 का अ+धकार”Mazdoor Kisan Shakti Sangathan

“The Right to Information, The Right to Live”

“!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता है”Bhartṛhari—Nītiśatakam

“Knowledge is such a treasure which cannot be stolen”

“Invent a New India Using Knowledge”

है”ह”ह

IS 10428 (1983): Glossary of terms relating to doors [CED11: Doors, Windows and Shutter]

IS : 10428-1983

UDC 69’928’1 : 001’4 IS0 1804-1972

Indian Standard

GLOSSARY OF TERMS RELATING TO DOORS

( IS0 Title : Dsoors-Terminology )

National Foreword

This Indian Standard which is identical with ISO 1804-1972 ‘Doors-Terminology’, issued

by the International Organization for Starrdardization (ISO), was adopted by the Indian Standards

Institution on the recommendation of the Doors, Windows and Shutters Sectional Committee and

approved by the Civil Engineering Division Council.

Wherever the word ‘Internation-al Standard’ appears, referring to this standard, it should

be taken as ‘Indian Standard’.

Corresponding French terms in the text and Appendix giving ‘List of corresponding

terms in German’ have been deleted from the International Standard. Consequently, foot-notes

in relation to these terms stand deleted.

Adopted 27 January; 1983 @I April 1983, ISI Gr 3

INDIAN STANDARDS INSTITUTIQN

MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG

NEW DELHI 110002

IS : 10428-1983

IS0 1804-l 972

Doors - Terminology

0 INTRODUCTION

In this International Standard some terms refer to details in doors or in door frames which do not apply to all types of doors. However, it is necessary to include these terms in a general terrninology for all types of hinged or pivoted doors.

1 GENERAL

1.1 Scope and field of application

This International Standard gives the terminology for hinged or pivoted doors of all materials used in building construction.

1.2 General definition

doorset : An assembly including a fixed part (the door frame), one or more movable parts (the door leaves) the function of which is to allow or to forbid the access, and their hardware.

NOTE - The doorset may include sill, overpanel and side panel(s)

2 TERMINOLOGY

The terms, with their translation in French, correspond to the definitionsgiven below and to the illustrations given in the Annex.

2.1 Terms relating to the components

la

2.1.1 TERMS RELATING TO THE STRUCTURAL OPENINGS

Structural opening

The void within a wall or partition designed to receive a doorset.

Structural opening with non-rebated reveal (Figure 1)

lb Structural opening with rebated reveal (Figure 2)

11 Structural reveal (rebated or non-rebated)

12 Soffit

13 Vertical side

14 Sill

15 Structural rebate

16 Depth of rebate

17 Width of rebate

18 Finished floor

P

IS : 10428-1983 IS0 1804-l 972

2.1.2 TERMS RELATING TO THE DOOR FRAMES

2 Door frame

2a

2b

2c

20

21

22

23

24

25

26

27

28

29a

The frame in which a door (door-leaf) is

hung.

Door frame with rebate (Figure 3)

Door frame without rebate (Figure 4)

Door frame with transom (Figure 5)

Door frame reveal (rebated or non-rebated)

Head

Transom

Jamb

Sill

Rebate

Depth of rebate

Width of rebate

Trim

29b

Butt type door frame

see Figures 10, 11, 12, 14, 15, 16.

Wrap around door frame

see Figures 13 and 17.

NOTE - Only door frames with trim incor- porated can be of the wrap around type.

2.1.3 TERMS RELATING TO THE DOORS

3 Door

31

32

33

34

35

36

37

36a

38b

The door leaf of a single leaf door.

Internal door

Door the two faces of which are situated

internally.

External door

Door with at least one face externally.

Square edge door

Rebated door

Rebate

Overlap

Door leaf

huare edge overpanel

Rebated overpanel

2.2 Terms relating to dimensions

Letters with numbers denote work sizes.

22.1 HEIGHTS

A

Al A2

d

Co-ordinating height between opening and door frame or doorset

Height of structural reveal

Height of door frame or doorset

Co-ordinating height between door frame and door leaf

dz Door frame reveal height

d’z Clear opening height

d3 Height~of door leaf (inside door frame)

d’3 Door leaf height overall lipping

2.2.2 WIDTHS

B Co-ordinating width between opening and door frame or doorset

Bl Width of structural reveal

62 Width of door frame or doorset

e Co-ordinating width between door frame and door leaf

e2 Door frame reveal width

e’2 Clear opening width

e3 Width of door leaf (inside door frame)

e’3 Door leaf width overall lipping

g Width of rebate (of the frame)

2.2.3 DEPlHS - THICKNESSES

,C Co-ordinating thickness between opening and door frame or doorset

Cl Depth of structural reveal

c2 Doorset or door frame thickness

f Co-ordinating depth between door frame and door leaf

f2 Door frame reveal depth

f3 Thickness of door leaf (inside door frame)

f’3 Door leaf thickness overall lipping

22.4 OTHER DIMENSIONS

i Joint clearance

k,k’;k” Clearance between door frame and door leaf

k “’ Clearance between door leaf and finished floor

3

IS : 10428-1983 IS0 1804-1972

ANNEX

ILLUSTRATION OF TERMS

A.1 STRUCTURAL OPENINGS

112

* 13

la

FIGURE 1 FIGURE 2

A.2 DOOR FRAMES

FIGURE 3 FIGURE 4 FIGURE 5

A.3 DOORS _--- I

I I I 34 c

I 1 (37)

35, L_--

33 9 ! (37)

I I

FIGURE 7

FIGURE 6 FIGURE 8 4

A.4 REBATES

IS : 10428-1983 IS0 1804-l 972

FIGURE 9

DIMENSIONS

FIGURE 10 FIGURE 7 1

28 21 I .-I

FIGURE 12

5

FIGURE 13

IS : 10428-1983

IS0 1804-l 972

- -- -.--- __--._-- ?z -._._.__ I3 ------.-______ _- 2

FIGURE 14

FIGURE 16

KEY

FIGURE 15

It--i--7--_)I e=830

+_f,_= a27 f i 4

4.26 m

FIGURE 17

Walls or partitions

Wooden frames

Metal frames

Door leaves

Modular co-ordinating sizes

Non-modular co-ordinating sizes

Work sizes

Level datum

6

Printed at Simco Printin Press, Delhi, India