Ironing system (pressurised) - Morphy Richards · PDF fileIroning system (pressurised) ... on your steam generator or the iron, please return to Morphy Richards service department

Ironing system (pressurised)Please read and keep these instructions

TM

Getting the best from your new ironing system....Safety firstCaution must be used when handling this appliance as it does get very hot. Alwaysswitch off the unit and allow to cool before cleaning or storing.

Water tankThe fixed water tank can be re-filled at any time during ironing.

PerformanceTo extend the performance and life of your IntelliDome generator, ensure that youreplace the anti-scale filter according to the on-board indicator. Regularly remove anycalcium build-up which may have accumulated in the boiler (see cleaning instructions).

If you have a problem or complaint, please call our dedicated UK based helplinebefore returning your product to the retailer from where it was purchased.

UK Helpline: 0844 871 0960 Replacement Parts: 0844 873 0726Ireland Helpline: 1800 409 119

!To improve the life of your new product and to ensure the cleanliness of yourclothes, we strongly recommend the use of distilled or demineralised water.

Upon registration with Morphy Richards(UK & ROI only)

Register online for your 2 yearguarantee. See back of thisinstruction book for details.(UK and Ireland customers only)www.morphyrichards.co.uk

RN42236 MUK Rev 2

www.homeofthehouseproud.com

www.facebook.com/LoveYourHome

www.twitter.com/LoveYourIroning

For competitions, product hints and tips and much more,join us online at our blog, Facebook or Twitter pages.

RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 1

2 UK Helpline 0844 871 0960 Replacement Parts 0844 873 0726 Ireland Helpline 1800 409 119


3For details of other Morphy Richards products, please see our website:

IMPORTANT SAFETY INSTRUCTIONS 4-6

ELECTRICAL REQUIREMENTS 6

BEFORE USE 6

QUICK START GUIDE 7

COMPONENTS OF YOUR INTELLIDOME 8

CONTROL PANEL FEATURES 9

INSTRUCTIONS FOR USE: TEMPERATURE GUIDE 9

WATER MANAGEMENT 10

STEAM IRONING 11

DRY IRONING 12

WATER SPRAY 12

AUTO STANDBY DEVICE (SAFETY FEATURE) 13

DOUBLE ACTION LIMESCALE REDUCTION SYSTEM 13

FLUSHABLE BOILER FEATURE 14

ROUTINE MAINTENANCE 15

HELPLINE & WEBSITE 15

GUARANTEE 16

CONTENTS



This appliance can be used by children agedfrom 8 years and above and persons withreduced physical, sensory or mental capabilitiesor lack of experience or knowledge, if they havebeen given supervision or instruction concerninguse of the appliance in a safe way andunderstand the hazards involved. Children shallnot play with the appliance. Cleaning and usermaintenance shall not be made by childrenwithout supervision.

Keep the steam generator and its cord out ofreach of children less than 8 years of age when itis energized or cooling down.

The steam generator must not be left unattendedwhile it is connected to the supply mains.

The plug must be removed from the socket-outletbefore the water reservoir is filled with water.

The steam generator must be used and rested ona stable surface.

When placing the steam generator unit on thebase or its heel, ensure that the surface on whichthe heel is placed is stable.

The steam generator is not to be used if it hasbeen dropped, if there are visible signs ofdamage or it is leaking.

IMPORTANT SAFETY INSTRUCTIONS

l

l

l

l

l

l

l



The use of any electrical appliance requiresthe following common sense safety rules:

Primarily there is danger of injury or deathand secondly the danger of damage to theappliance. These are indicated in the text bythe following two conventions:

WARNING: Danger to the person!

IMPORTANT: Damage to the appliance!

In addition, we offer the following safetyadvice.

Location• Do not use outdoors.

• Locate the steam generator horizontally on therest plate of your ironing board (if large enough)or on a heat resistant stand at the same heightas your ironing board or below it. Always ensurethe generator is on a firm level surface whenironing.

• IMPORTANT: Do not use the product on asurface which could be damaged by heat orsteam such as a worktop or a polished woodsurface.

• If in doubt, contact Morphy Richards.

Children• Children do not understand the dangers

associated with operating electricalappliances. Never allow children to use, orplay with, this appliance.

• Close supervision is necessary when anyappliance is used near children.

Personal Safety• Do not use the vertical steam feature on

clothes that are being worn.

• WARNING: Burns can occur from touchinghot metal parts, hot water or steam. Usecaution when using your steam generator.If your iron is placed for a few momentson the iron rest plate, this plate may reachvery high temperatures. In this instance,do not touch the iron soleplate or the ironrest plate until the iron and the iron resthave cooled down.

• WARNING: To protect against the risk ofelectric shock, do not immerse theappliance in water or in any other liquid.

• Do not leave the steam generator unattendedwhilst plugged in or on an ironing board.Never allow the mains lead to over hang thework surface.

• The mains socket should always be switchedoff before plugging or unplugging from thesocket. Never yank the cord to disconnectfrom the socket, instead, grasp the plug andpull to disconnect.

Other safety considerations• Use the steam generator only for its intended

use.

• Never hold the steam generator under a tap.

• Always disconnect the steam generator fromthe electrical supply when cleaning or whennot in use.

• If the supply cord is damaged, it must bereplaced by the manufacturer, its serviceagent or similarly qualified person(s) in orderto avoid a hazard.

• Do not operate the steam generator with adamaged cord or if the iron has beendropped or if there are visible signs ofdamage or if it is leaking. To avoid the risk ofelectric shock, do not disassemble the iron orsteam generator, but telephone MorphyRichards for advice. Incorrect reassemblycan cause a risk of electric shock when thesteam generator is used.

• If the need arises to change the mains cableon your steam generator or the iron, pleasereturn to Morphy Richards servicedepartment at the address on the back page.

• WARNING: Dangerof scalding. Beforeattempting to cleanthe boiler, alwaysleave for at least2 hours.

• WARNING: Take care when opening theboiler for cleaning, as pressure may bereleased to the atmosphere. If this occurs,allow the pressure to release beforeremoving the boiler access screw.



Special instructions

• If your steam generator does not work, checkthe following points:

Has the iron temperature control been set tothe required temperature? Is the plug in itssocket? Is the plug itself or the socket faulty?(Check by plugging in another appliance).

• To prevent damage to the textile beingironed, follow the temperature guide carefully.(Test on the inside of the hem of thegarment).

• If you drop or severely knock your steamgenerator, this could cause internal damageeven if the outside appears alright. Have itchecked by a qualified electrician.

• The temperature of accessible surfaces maybe high when the appliance is operating.

ELECTRICALREQUIREMENTSCheck that the voltage on the rating plate ofyour appliance corresponds with your houseelectricity supply which must be A.C.(Alternating current).

If the socket outlets in your home are notsuitable for the plug supplied with thisappliance, the plug should be removed andthe appropriate one fitted.

WARNING: A damaged or severed mainscable fitted with a plug should never beconnected to the mains supply. It mustbe destroyed, as a damaged cablebecomes hazardous if connected to apower socket.

Should the fuse in the 13 amp plug requirechanging, a 13 amp BS1362 fuse must befitted.

WARNING: This appliance must beearthed.

BEFORE USE

Remove any protective cover from thesoleplate and the base unit, if any.

Unwind and straighten the supply cord ‡and mains cable ·.

When ironing with the temperature set at2-dot setting, the steam output should be setat the lower end of the steam range.

Textiles and clothes are supposed to carryironing instructions. If they don’t, you shouldfollow the fabric guide on page 7, but be sureto test the temperature by ironing the hem ofthe garment or similar area first.

If you turn the control dial down from a hotsetting to a cooler setting, wait until the irontemperature has stabilised before youcontinue ironing.



QUICK START GUIDE

1 Unpack the product and remove anyadditional packing materials as required.

2 Place the product onto a level surface orironing board stand.

3 Make sure the anti-scale drawer ‰ is fullyclosed.

4 Using the beaker provided Á or suitablemeasuring jug, fill the water tank fl to the fullmark.

5 Set the iron control knob to 3-dot.

6 Connect the unit to the power supply, the LCDdisplay screen illuminates for 1 second, a shortbeep is heard, then the LCD display screen willturn off. The product is now in STANDBY modeand the STANDBY ICON will be displayed in thecorner of the LCD display screen A.

7 Press the POWER STANDBY button on thecontrol panel and the unit will heat to theworking temperature, the LOW STEAM ICONwill flash whilst the heating cycle takes placeand will remain illuminated when the boiler isready to deliver steam B.

Note: At this time, the pump will fill the boilerwith water. You will hear the pump operating,this is quite normal and will last forapproximately 25 seconds.

8 Press the steam trigger ⁄ to deliver steam tothe iron. Releasing the trigger will extinguishsteam.

9 When ironing is complete, press the POWERSTANDBY button on the control panel to endthe session. The LCD icons will dim until theunit is disconnected from the mains supply,only then will the LCD switch off.

10 Allow the unit to cool, drain the water tank(see page 10), then store away.

AUTO STANDBY DEVICE(SAFETY FEATURE)If the unit is not operated for approximately 15minutes, it will revert to STANDBY mode and thePOWER STANDBY ICON will flash in the LCDdisplay screen C. To re-activate the unit, pressthe POWER STANDBY button or the steamtrigger ⁄ and the unit will revert back to theprevious setting.

fl„

⁄

‰

Á

400ml

‡

·

A

C

B



fl

·

fi

›

‡

¤

‹

⁄ ‡

‚

COMPONENTS OF YOUR INTELLIDOME

„ Control panel (see page 9)

ÊÂ

UNDERSIDE VIEW

Á

400ml

Iron unit

⁄ Steam trigger

¤ Temperature indicator light

‹ Temperature control knob

› Soleplate

Base unit

fi Water tank filler cap

fl Water tank

‡ Supply cord (steam)

· Mains cable

‚ Cable storage clip

„ Control panel

‰ Anti-scale filter drawer

Filter cartridge(see page 13)

Â Boiler access screw and cover(cleaning only)

Ê Boiler access tool

Á Filler cup

Î/Ï/Ì/ÓSpray feature (see page 12)

Ë/È/ÍWater tank drain (see page 10)

‰/



Symbol

(120°C Max) Cool (160°C Max) Warm (210°C Max) Hot

Control knobpositions

Do not ironat all

Fabric Nylon, Acetatese.g. AcrilanCourtelle, Orlon

Wool, Polyestermixtures e.g.Polyester/CottonTriacetates, e.g.Tricel/Polyester

Cotton, LinenRayon, Rayonmixtures,e.g. Rayon/Linen

Ironing Iron on the wrongside, if moisturerequired use dampcloth (Not Acetate)

Fabrics requiring thissetting usually requiresteam pressing for heavycotton, denim etc.

Steaming

Dry

‘Max setting’

INSTRUCTIONS FOR USE

Temperature guide

Low steam settings High steam settings

The control consists of an LCD display screenand 3 buttons: POWER STANDBY button 1and STEAM SETTING +/- buttons 4, as shownbelow D:

POWER STANDBY buttonIntellidome outlineLCD display screenSteam level +/-Standby modeClean boiler / fill boiler indicatorAnti-scale filterAnti-scale filter alignment arrows

Anti-scale drawer displayBoiler outlineLow water displayNo steamLow steam levelMedium steam levelHigh steam level

1 2 3 4

5 6 7 8 9 10 11 12 13 14 15

D

CONTROL PANEL FEATURES „

12345678

9101112131415



1. WATER MANAGEMENT

Filling1 Place the steam generator on a stable ironing

board or table, with the iron resting on itsstand.

2 Open the filler cap at the front of the watertank and fill to the FILL TO HERE line usingthe filler cup Á provided or a suitable jug.

WE RECOMMEND YOU USE DISTILLED ORDEMINERALISED WATER IN THIS UNIT.

Never use battery topping up fluid or watercontaining any substances like starch orsugar, or defrosted water from a refrigerator.

3 Always drain out any remaining water afteruse (see instructions below).

Re-filling ‘in use’1 Refilling can be done whilst the appliance is

in operation. It is not necessary to wait forthe appliance to cool down.

2 Open the filler cap at the front of the watertank and fill as necessary.

Low water cutout E

The unit has an electronic system to monitor thewater level. When the level is low, the LOWWATER ICONS 6/11 will flash and a beep willbe heard for 10 seconds to warn the user to refillthe tank. Once the unit has been filled, the LOWWATER ICONS will disappear.

NOTE: When the LOW WATER WARNINGICONS activate, the boiler will still deliver steamfor a short period then the unit will switch off,this action saves the unit from damage.

Draining the water tank FWhen ironing is complete, we advise you toempty any water left in the tank.

This model is fitted with a drain system situatedat the front of the unit.

1 Disconnect the unit from the mains supply.

2 Place the unit on the sink drainer so water canrun away safely.

3 Push back the drain release catch Í and rotatethe tube Ë outwards using the tab È.

4 Water will now drain automatically.

5 Once the tank is empty, replace the tube makingsure it clips in place.

E

Water tank drain

Ë Drain tube

È Drain tube tab

Í Drain tuberelease catch

Í

ÈË ÈË

Í

Slide in thisdirection

Rotate tubeoutwards

F

6 11



1 Unwind and straighten the supply and powercords (‡ and ·).

2 Fill the water tank with clean tap water (seepage 10).

3 Connect the unit to the mains supply.

The LCD display screen „ will illuminate for1-second and be accompanied with a shortbeep sound, then the unit will turn off and willremain in STANDBY mode until re-activated.The STANDBY ICON is also visible in thecorner of the display screen.

4 Press the POWER STANDBY button to activatethe unit and set the iron temperature controldial on the iron to the 3-dot setting.

At this time, the pump will fill the boiler withwater. You will hear the pump operating - thisis quite normal. The filling sequence takesapproximately 25 seconds.

The unit will heat and automatically default tothe LOW STEAM level, the STEAM ICON willflash on the display screen and will remainpermanently on when steam is available forironing.

The AUTO STANDBY feature will activate ifthe iron is not used for 15 minutes. Press thePOWER STANDBY button or steam trigger toreactivate the iron.

Steam settingsTo increase or decrease the steam setting, pressthe STEAM SETTING +/- buttons. Thesesettings include:NO STEAM G,LOW STEAM LEVEL H,MEDIUM STEAM LEVEL Iand HIGH STEAM LEVEL J.

LOW STEAM LEVEL

MEDIUM STEAM LEVEL

HIGH STEAM LEVEL

The STEAM ICON will flash until the unit reachesthe selected temperature. Once the temperaturehas been reached, the STEAM ICON will remain lit.

When navigating though the steam settings, aSHORT BEEP will be heard for every operationof the STEAM SETTING +/- buttons a furtherLONGER BEEP will be heard once the unit hasreached the selected setting.

Note: During ironing, the pump will operateperiodically to ‘top up’ the boiler with water.This is quite normal and lasts for a fewseconds only.

VERTICAL STEAMHold the iron in avertical positionbetween 1cm and 2cmaway from the item K .Press the steam trigger⁄, this will createvertical steam. Thisfeature is especiallyuseful for removingcreases from hangingclothes, curtains, wallhangings etc.

STEAM FUNCTIONDuring the steaming process, small amounts ofwater may be ejected from the soleplate. This isnormal and can be avoided by using the steamfor short amounts of time and only when the ironis at the correct temperature (the indicator lighton the iron goes out when ready).

Sudden jolts of the boiler unit can also causewater droplets on the soleplate; therefore, donot move the base unit during ironing. Werecommend for the first time ironing that youiron over an old towel.

2. STEAM IRONING

G

H

I

J

K

NO STEAM



3. DRY IRONING

Always make sure there is water in the tankotherwise the LOW WATER indicator willactivate.

1 Always make sure the water tank is quarterfull, otherwise the LOW WATER INDICATORICON will activate.

2 Connect the unit to the mains supply.

3 The LCD display screen will illuminate for 1second accompanied by a short beep sound,the unit will then turn off and will remain inSTANDBY mode until re-activated. TheSTANDBY ICON will be visible in the cornerof the display screen.

4 Press the POWER STANDBY button toactivate the unit and set the iron temperaturedial to the dot setting required.

5 Press the STEAM +/– buttons until theNO STEAM ICON is displayed on the LCDdisplay screen L.

NO STEAM

6 Turn the temperature dial on the iron to thedot setting required.

7 The temperature indicator light on the ironwill glow indicating the iron is heating.

8 When the required temperature is reached,the temperature indicator light will go out andthe iron is now ready to use. It is always agood idea to begin with “cool fabrics” andwork up to higher settings. An iron heats upquicker than it cools down so you’ll savetime and electricity.

9 The AUTO STANDBY feature will activate ifthe iron is not used for 15 minutes. Press thePOWER STANDBY button or the iron steamtrigger ⁄ to reactivate the unit.

WATER SPRAY (certain models only)

Certain models are fitted with a water sprayfeature. Stubborn creases and excessivelydry clothing can be softened by damping thematerial with water. This procedure meansironing can be achieved without applyingexcessive pressure.

Filling water spray tank M

To fill the water spray tank with water, pressthe release button Ì and lift away the sprayunit Î.

Pull the tank Ó away from the spray unit in adownward direction, taking care not todamage the tank, and fill water to the ‘Full’mark.

Water spray unit (certain models only)

Î Spray unit assembly

Ï Spray button

Ì Spray unit release button

Ó 20ml spray bottle

Re-assembly M

Attach the tank to the spray unit, taking careto align the parts correctly.

Locate the spray unit to the front of the ironand press it home until the unit locks intoplace.

Press the pump Ï a few times to purge theair from the system, when a fine mist ofwater is created, the unit is ready for use.

L

Î

Ó

ÌÏÎM



4. AUTO STANDBY DEVICE (SAFETY FEATURE)

If any of the function buttons are not operated forapproximately 15 minutes, the unit will revert toSTANDBY mode and the POWER STANDBY ICONwill flash in the LCD display N. To re-activate theunit, press the POWER STANDBY button or theiron steam trigger ⁄ and the unit will revert backto the previous setting.

5. DOUBLE ACTION LIMESCALE REDUCTION SYSTEM

CHANGING THE FILTERIMPORTANT: This procedure must bedone when the unit is connected to themains supply.

The anti-scale filter is designed to reduce thebuild-up of limescale which occurs duringsteam ironing, this will prolong the workinglife of your iron. However, please note thatthe anti-scale filter will not completely stopthe natural process of limescalebuild-up.

When the anti-scale filter needs replacing, theFILTER ICONS will flash on the LCD screen Oaccompanied by a loud beep noise, when thisoccurs, continue ironing until complete then wesuggest you change the filter.

Remove the filter drawer ‰ to replace the filtercartridge . Please wait approximately 10seconds before replacing the drawer to allowthe onboard timer circuit to reset.

If the change filter instruction is ignored, the unitwill still function, however the product life maybe affected.

Incorrect filter installationIf the filter is installed incorrectly, the FILTERICONS will illuminate P, accompanied by aLONGER BEEP.

Once the filter is aligned correctly, the icons willdisappear.

Replacing the filter

The filter cartridge is situated inside thefilter drawer ‰ below the LCD screen Q.

To replace the filter, simply pull out thedrawer and replace the filter R.

Replace the drawer making sure it is pushedfirmly into position.

Replacement filtersTo obtain replacement filters, telephoneour spares number on: 0844 873 0726.

• If a new filter is not available, you maycontinue operating the appliance, but scalewill build up in the system. Replace the filteras soon as possible. Part Number 01030.

R

FilterCartridge

‰FilterDrawer

Q

N

O

P

‰/



FLUSHABLE BOILERFEATURE

To extend the life of the product we recommendyou periodically rinse out the boiler to removeany limescale build-up.

• When the boiler needs cleaning, the icons belowwill be displayed on the LCD screen S.

WARNING: Only clean the boiler when theunit is cold. If cleaning takes place afterironing, please allow 2 hours for theboiler to cool to ambient temperature.

1 When the CLEAN BOILER ICON is displayed onthe LCD screen, finish ironing, drain the watertank (see tank drain instruction, pages 10)and leave the unit for a few hours until cold.

2 Stand the steam generator close to the sinkdrainer. Ensure all water is drained from thewater tank (see page 10).

3 Remove the iron from its rest.

4 Turn the base unit upside down and unclip thecover to expose the boiler access screw Â T.Type A cover folds back to expose the boileraccess screw, type B cover rotates to the side.

5 Use the tool Ê provided to remove the screw inan anti-clockwise direction U.

6 Fill the filler cup to the MAX mark with ordinarytap water and pour this through the access holeinto the boiler V.

7 Move the base unit back and forth a few timesthen pour the water out into the sink orcontainer W.

8 Repeat this procedure a number of times untilthe water is clean and clear, making sure allwater is removed.

9 Replace the boiler access screw using the toolprovided but do not use excessive force X.

10 Reposition the cover and place the tool in thespace provided, ensuring it is securely clippedinto place.

The cleaning procedure is now complete.

W

X

V

U

S

Type A cover Type B coverT T

Unclip andpull back

Unclip androtate



ROUTINE MAINTENANCE

Soleplate cleaning

To clean a stainless steel soleplate

To keep the soleplate of your iron clean and freeof limescale, we recommend that you use one ofthe gentle chrome, silver or stainless steelcleaners that are generally available. Alwaysfollow the manufacturer’s instructions. To cleanoff melted man-made fibres, set the iron at 3-dotposition and pass it over a clean piece of cottonwhich will draw the deposit off the surface.

To clean a coated soleplate

In the unlikely event of any man-made fibrefusing to the soleplate, set the iron at the3-dot position and pass it over a clean piece ofcotton, this will draw the deposit off the surface.

Do not use scouring powder or solution, as thiscould cause damage to the coating.

To clean the exteriorAllow the steam generator to cool and wipe overwith a damp cloth and mild detergent, then wipewith a dry cloth.

HELPLINEIf you have any difficulty with your appliance, donot hesitate to call us.

We are more likely to be able to help than thestore from where you bought it.

Please have the following information ready toenable our staff to deal with your query quickly.

• Name of the product

• Model number as shown on the underside of theappliance.

• Serial number as shown on underside of theappliance.

UK Helpline 0844 871 0960

Replacement Parts 0844 873 0726

Ireland Helpline 1800 409 119

WEBSITEYou may also contact us through our website,or visit the site to browse and purchaseappliances, spare parts and accessories fromthe extensive Morphy Richards range.


16

Morphy Richards products are intended for household use only.

Morphy Richards has a policy of continuous improvement in product quality anddesign. The company therefore, reserves the right to change the specification ofits models at any time.

The After Sales DivisionMorphy Richards LtdMexborough, South Yorkshire, England, S64 8AJ

Helplines (office hours)UK 0844 871 0960Spare Parts 0844 873 0726Republic of Ireland 1800 409 119

RN42236 MUK Rev 2 10/10

REGISTERING YOUR TWO YEAR GUARANTEE

Your standard one year guarantee isextended for an additional 12months when you register theproduct within 28 days of purchasewith Morphy Richards. If you do notregister the product with MorphyRichards within 28 days, yourproduct is guaranteed for 1 year. Tovalidate your 2 year guaranteeregister with us online atwww.morphyrichards.co.uk

N.B. Each qualifying product needsto be registered with MorphyRichards individually.

Please note that the 2 yearguarantee is only available in theUK and Ireland. Please refer to theone year guarantee for moreinformation.

YOUR ONE YEAR GUARANTEE

It is important to retain the retailer’sreceipt as proof of purchase. Stapleyour receipt to this back cover forfuture reference.

Please quote the followinginformation if the product developsa fault. These numbers can befound on the base of the product.

Model no.

Serial no.

All Morphy Richards products areindividually tested before leaving thefactory. In the unlikely event of anyappliance proving to be faulty within28 days of purchase, it should bereturned to the place of purchasefor it to be replaced.

If the fault develops after 28 daysand within 12 months of originalpurchase, you should contact theHelpline number quoting Modelnumber and Serial number on theproduct, or write to MorphyRichards at the address shown.

You may be asked to return a copyof proof of purchase.

Subject to the exclusions set outbelow (see Exclusions), the faultyappliance will then be repaired orreplaced and dispatched usuallywithin 7 working days of receipt.

If, for any reason, this item isreplaced during the 1 yearguarantee period, the guarantee onthe new item will be calculated fromoriginal purchase date. Therefore itis vital to retain your original tillreceipt or invoice to indicate thedate of initial purchase.

To qualify for the 1 year guarantee,the appliance must have been usedaccording to the instructionssupplied. For example, filters shouldhave been emptied regularly.

EXCLUSIONSMorphy Richards shall not be liableto replace or repair the goods underthe terms of the guarantee where:

1 The fault has been caused or isattributable to accidental use,misuse, negligent use or usedcontrary to the manufacturer’srecommendations or where the faulthas been caused by power surgesor damage caused in transit.

2 The appliance has been used on avoltage supply other than thatstamped on the products.

3 Repairs have been attempted bypersons other than our service staff(or authorised dealer).

4 The appliance has been used forhire purposes or non domestic use.

5 The appliance is second hand.

6 Morphy Richards are not liable tocarry out any type of servicingwork, under the guarantee.

7 Plastic filters for all MorphyRichards kettles and coffee makersare not covered by the guarantee.

8 Batteries and damage from leakageare not covered by the guarantee.

• This guarantee does not confer anyrights other than those expressly setout above and does not cover anyclaims for consequential loss ordamage. This guarantee is offeredas an additional benefit and doesnot affect your statutory rights as aconsumer.

For electrical products sold within theEuropean Community. At the end of theelectrical products useful life, it shouldnot be disposed of with householdwaste. Please recycle where facilities exist.Check with your Local Authority orretailer for recycling advice in yourcountry.

UK Helpline 0870 060 2614 Replacement Parts 0870 157 6645 Ireland Helpline 1800 409119


Documents

Ironing system (pressurised) - Morphy Richards · PDF fileIroning system (pressurised) ... on your steam generator or the iron, please return to Morphy Richards service department