IPv6 Routing

IPv6 Routing 2

Describing IPv6 Routing

IPv6 Routing 3

IPv6 Routing Table

IPv6 routing protocols still use the longest-match prefix as the oruting algorithm for route selection as their equivalent did in IPv4.

Ipv6 routing table is handled and managed separately from the IPv4 routing table when both protocols are enabled simultaneously.

IPv6 unicast-routing Enabled on Cisco routersrouter start forwarding

IPv6 packets between its interfaces using IPv6 routing table.

IPv6 Routing 4

Administrative Distance Administrative distance remains same as in IPv4 as displayed

by the following table:

IPv6 Routing 5

Displaying IPv6 Routing Table

Following addresses are automatically inserted in the routing table:

Multicast-prefix Link-local prefix

Default ipv6 route

Static Routing

IPv6 Routing 7

Static Routing Overview

Static routes are manually configured and define an explicit path between two networking devices.

Restrictions for Implementing Static Routes for IPv6: IPv6 static routes do not currently support the tag and

permanent keywords of the IPv4 ip route command. IPv6 does not currently support inserting static routes into

virtual routing and forwarding (VRF) tables.

IPv6 Routing 8

Static IPv6 Routes Prerequisite for static IPv6 routes:

Before configuring the router with a static IPv6 route: Enable forwarding of IPv6 packets using the ipv6 unicast-

routing global configuration command enable IPv6 on at least one interface configure an IPv6 address on that interface.

Static routes are useful for smaller networks with only one path to an outside network and to provide security for a larger network for certain types of traffic or links to other networks that need more control.

Types of static routes1. Directly attached static routes2. Fully specified static routes3. Floating static routes

IPv6 Routing 9

Directly Attached Static Routes

In directly attached static routes, only the output interface is specified.

The destination is assumed to be directly attached to this interface, so the packet destination is used as the next hop address.

ipv6 route 2001:0DB8::/32 ethernet1/0 all destinations with address prefix 2001:0DB8::/32 are

directly reachable via interface Ethernet1/0. Directly attached static routes are candidates for insertion

in the IPv6 routing table only if they refer to a valid IPv6 interface; that is, an interface that is both up and has IPv6 enabled on it.

IPv6 Routing 10

Fully Specified Static Routes

Both the output interface and the next hop are specified.

This form of static route is used when the output interface is a multi-access one and it is necessary to explicitly identify the next hop.

The next hop must be directly attached to the specified output interface. ipv6 route 2001:DB8:/32 ethernet1/0 2001:0DB8:3000:1 A fully specified route is valid (that is, a candidate for

insertion into the IPv6 routing table) when the specified IPv6 interface is IPv6-enabled and up.

IPv6 Routing 11

Floating Static Routes Floating static routes are static routes that are used to back up

dynamic routes learned through configured routing protocols. A floating static route is configured with a higher administrative

distance than the dynamic routing protocol it is backing up. As a result, the dynamic route learned through the routing

protocol is always used in preference to the floating static route. If the dynamic route learned through the routing protocol is lost,

the floating static route will be used in its place. ipv6 route 2001:DB8:/32 ethernet1/0 2001:0DB8:3000:1 210

Any of the three types of IPv6 static routes can be used as a floating static route.

Note: By default, static routes have smaller administrative distances than dynamic routes, so static routes will be used in preference to dynamic routes.

IPv6 Routing 12

Implementing Static Routes for IPv61. Configuring a Static IPv6 Route

IPv6 Routing 13

Examples

Directly Attached Static Route through Point-to-Point Interface Router(config)# ipv6 route 2001:0DB8::/32 serial 0

Directly Attached Static Route on Broadcast Interface Router(config)# ipv6 route 2001:0DB8::1/32 ethernet1/0

Fully Specified Static Route on Broadcast Interface Router(config)# ipv6 route 2001:0DB8::1/32 ethernet1/0

fe80::1

IPv6 Routing 14

Configuring a Floating Static IPv6 Route

STEPS 1. enable

2. configure terminal

3. ipv6 route ipv6-prefix/prefix-length {ipv6-address | interface-type interface-number [ipv6-address]} [administrative-distance] [administrative-multicast-distance | unicast | multicast] [tag tag]

IPv6 Routing 15

Verifying Static IPv6 Route Configuration and Operation

show ipv6 static To display a set of static routes and the installed status of each,

that is, whether an entry for each route appears in the IPv6 routing table.

show ipv6 route To confirm that installed routes are in the IPv6 routing table and

that each route definition reflects the expected cost and metric. If a static route that you have configured does not appear in the IPv6

routing table, it is possible that there is a lower administrative distance from another source in the table, such as from a routing protocol.

If a lower administrative distance exists, the static route is "floating" and will be inserted into the routing table only when the route learned through the routing protocol disappears. I

IPv6 Routing 16

show ipv6 static

Router# show ipv6 static IPv6 Static routes Code: * - installed in RIB * 2001:0DB8:3000:0/16, interface Ethernet1/0, distance 1 * 2001:0DB8:4000:0/16, via nexthop 2001:0DB8:1:1, distance 1   2001:0DB8:5000:0/16, interface Ethernet3/0, distance 1 * 2001:0DB8:5555:0/16, via nexthop 2001:0DB8:4000:1, distance 1   2001:0DB8:5555:0/16, via nexthop 2001:0DB8:9999:1, distance 1 * 2001:0DB8:5555:0/16, interface Ethernet2/0, distance 1 * 2001:0DB8:6000:0/16, via nexthop 2001:0DB8:2007:1, interface

Ethernet1/0, distance 1

Implementing OSPF for IPv6

OSPFv3

IPv6 Routing 18

Similarities Between OSPFv2 and OSPFv3

IPv6 Routing 19

Prerequisites for Implementing OSPF for IPv6

Before you enable OSPF for IPv6 on an interface, you must do the following: Complete the OSPF network strategy and planning for your

IPv6 network. For example, you must decide whether multiple areas are required.

Enable IPv6 unicast routing. Enable IPv6 on the interface. Configure the IP Security (IPSec) secure socket application

program interface (API) on OSPF for IPv6 in order to enable authentication and encryption.

IPv6 Routing 20

Differences Between OSPFv2 and OSPFv3

In OSPF for IPv6, a routing process does not need to be explicitly created. Enabling OSPF for IPv6 on an interface will cause a routing

process, and its associated configuration, to be created. In OSPF for IPv6, each interface must be enabled using

commands in interface configuration mode. This feature is different from OSPF version 2, in which

interfaces are indirectly enabled using the router configuration mode.

Some of the notable changes include: platform-independent implementation protocol processing per-link rather than per-node explicit support for multiple instances per link changes in authentication and packet format

IPv6 Routing 21

Differences Between OSPFv2 and OSPFv3

OSPFv3 runs over a link IPv6 uses the term link to indicate a communication facility or

medium over which nodes can communicate at the link layer OSPF interfaces connect to links instead of to IP subnets. OSPF for IPv6 therefore runs per-link instead of the IPv4 behavior

of per-IP-subnet, and the terms network and subnet are generally replaced by the term link.

This change affects the receiving of OSPF protocol packets, and the contents of hello packets and network LSAs.

IPv6 Routing 22

Differences Between OSPFv2 and OSPFv3

Link-local addresses are used OSPFv3 uses IPv6 link-local addresses to identify

the OSPFv3 adjacency neighbors. When configuring the ipv6 ospf neighbor

command, the IPv6 address used must be the link-local address of the neighbor.

IPv6 Routing 23

Differences Between OSPFv2 and OSPFv3

Multiple OSPFv3 instance support Separate autonomous systems, each running OSPF, use a common

link. A single link could belong to multiple areas. OSPFv3 uses a new field, called the Instance ID, to allow multiple

instances per link. To have two instances talk to each other, they must share the same

instance ID. By default, the instance ID is set to 0.

Multicast addresses FF02::5 —Represents all shortest path first (SPF) routers on the link-

local scope, equivalent to 224.0.0.5 in OSPFv2. FF02::6 —Represents all designated routers (DRs) on the link-local

scope, equivalent to 224.0.0.6 in OSPFv2.

IPv6 Routing 24

New LSA Types for IPv6

Link LSAs (Type 8) Have local-link flooding scope and are never flooded beyond the

link with which they are associated. Link LSAs provide the link-local address of the router to all other

routers attached to the link, inform other routers attached to the link of a list of IPv6 prefixes to associate with the link, and allow the router to assert a collection of Options bits to associate with the network LSA that will be originated for the link.

IPv6 Routing 25

New LSA Types for IPv6

Intra-Area-Prefix LSAs (Type 9) A router can originate multiple intra-area-prefix LSAs for

each router or transit network, each with a unique link-state ID.

The link-state ID for each intra-area-prefix LSA describes its association to either the router LSA or the network LSA and contains prefixes for stub and transit networks.

Implementing and Verifying OSPFv3

IPv6 Routing 27

IPv6 Configuration

Before configuring OSPFv3, IPv6 must be enabled with the ipv6 unicast-routing global configuration command.

Use the ipv6 address address/prefix-length [eui-64] interface configuration command to configure an IPv6 address for an interface and enable IPv6 processing on the interface.

The eui-64 parameter forces the router to complete the addresses' low-order 64-bits using an EUI-64 format interface ID.

IPv6 Routing 28

Steps to Configure OSPF for IPv6

1. Complete the OSPF network strategy and planning for your IPv6 network. For example, you must decide whether multiple areas are required.

2. Enable IPv6 unicast routing using the ipv6 unicast-routing command.

3. Enable IPv6 on the interface using the ipv6 ospf area command.

4. (Optional) Configure OPSFv3 interface specific settings, including area, router priority, and OSPFv3 path cost.

5. (Optional) Configure routing specifics from router configuration mode, including router priority, route summarization, and so on.

IPv6 Routing 29

Enabling OSPFv3 on an Interface

Most of the OSPFv3 configuration is done on the interface.

IPv6 Routing 30

Configuring OSPFv3 Routing Specifics

OSPFv3 routing specifics are configured from router configuration mode. For an IPv6-only router, a router ID parameter must be defined in the OSPFv3

configuration as an IPv4 address using the router-id router-id router configuration command.

OSPFv3 uses a 32-bit number for a router ID. The OSPFv3 router ID can be expressed in dotted decimal, allowing easy

overlay of an OSPFv3 network on an existing OSPFv2 network. If IPv4 is configured on the router, by default, the router ID is chosen in the

same way as it is with OSPFv2. The highest IPv4 address configured on a loopback interface becomes the

router ID. If no loopback interfaces are configured, the highest address on any other

interface becomes the router ID.

IPv6 Routing 31

OSPFv3 Route Summarization

Before Summarization:

After Summarization:

IPv6 Routing 32

OSPFv3 Configuration Example

IPv6 Routing 33

OSPFv3 Configuration Example

The following example configures an OSPF routing process 109 to run on the interface and puts it in area 1: ipv6 ospf 109 area 1

IPv6 Routing 34

Verifying OSPFv3

IPv6 Routing 35

Verifying OSPFv3 Neighbors

IPv6 Routing 36

Verifying OSPFv3 Database

IPv6 Routing 37

Lab Exercises

Configuring OSPF for IPv6 Case-study Configuring Static Routes and

Routing Protocols with Cisco