Upload
sudhanwa-kulkarni
View
475
Download
24
Embed Size (px)
Citation preview
7/28/2019 Introduction to ANSYS Workbench
1/29
MAE 656 - AdvancedComputer Aided Design
02. Ansys Workbench Doc 01
Introduction toAnsys Workbench
7/28/2019 Introduction to ANSYS Workbench
2/29
Main Screen
Components:Top menu Toolbox Messages Progress Project Properties
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
3/29
Top Menu File
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
4/29
Top Menu View
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
5/29
Top Menu Tools
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
6/29
Top Menu Units
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
7/29
Toolbox Analysis Systems
We have already predefined systems:
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
8/29
Toolbox Component Systems
We have the individual componentsof the systems:
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
9/29
Toolbox Custom Systems
We have predefined some systems with some interactionsbetween them. It is also possible to
define new custom-systems.
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
10/29
Project SchematicIt is possible to solvedifferent problemswith shared data.
It is also possible touse results from one
problem as inputdata to another one(i.e. fluid-structureinteraction)
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
11/29
Static Structural SystemWe will work with the Static Structural system.It is composed by:
Engineering data:Definition of material properties
Geometry:Def. of the problem geometry
Model:Def. of the mesh
Setup:
Def. of the boundary conditionsResults:
Contains the different results requied to the solver.
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
12/29
Static Structural System
Defined in a new workbenchwindow
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
Solved with Design Modeler
Solved with Mechanical module
7/28/2019 Introduction to ANSYS Workbench
13/29
Static Structural SystemSystem properly defined andhas no errors
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
System already defined butthat has to be updatedbecause there has beenmodifications in upper levels
The system is yet to bedefined
7/28/2019 Introduction to ANSYS Workbench
14/29
7/28/2019 Introduction to ANSYS Workbench
15/29
Engineering Data Sources
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
or, right click
7/28/2019 Introduction to ANSYS Workbench
16/29
Engineering Data - Charts & Tables
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
chart
table
7/28/2019 Introduction to ANSYS Workbench
17/29
Engineering Data - Exercise
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
Create a custom material for Aluminum Alloy type 5052-O.
The parameters that have to be defined are those of:
Density Thermal expansion Isotropic elasticity Yield and ultimate strength (defined as multilinear isotropic
hardening) Yield and ultimate strength as failure variables to be used in an
elastic material.The numerical value of each parameter can be obtained fromhttp://www.makeitfrom.com/
7/28/2019 Introduction to ANSYS Workbench
18/29
7/28/2019 Introduction to ANSYS Workbench
19/29
Design Modeler New Geometry
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
If instead of importing the geometry from another code or fromanother problem defined in the same workbench we decide to create anew geometry, clicking on NEW GEOMETRY will launch the desingmodeler.
7/28/2019 Introduction to ANSYS Workbench
20/29
7/28/2019 Introduction to ANSYS Workbench
21/29
Design Modeler Main Window
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
22/29
Design Modeler Selection
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
23/29
Design Modeler View Toolbar
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
24/29
7/28/2019 Introduction to ANSYS Workbench
25/29
Design Modeler Tree Outline
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
7/28/2019 Introduction to ANSYS Workbench
26/29
Design Modeler Parts
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
There are four different types of parts. Each one can be used in a typeof simulation: BARS, 2D, 3D and SHELLS.
7/28/2019 Introduction to ANSYS Workbench
27/29
Design Modeler More info.
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
More information about how to work with design modeler can befound in the Ansys Training Lectures:
DM-13.0 01 Planes and Sketches.pdf DM-13.0 02 3D Operations.pdf
7/28/2019 Introduction to ANSYS Workbench
28/29
Design Modeler Exercises
MAE 656 cba Dr. Xavier Martinez, 2012 02. Workbench Doc 01
1. Import geometry Cylinder_Surface.igs to design modeler2. Create structural frame defined in Assignment 01.
1. Defining points manually2. Using point data Frame Nodes.txt
In this second case, the roof beams have a cross section: 5 x 10 x 0.1 cm
7/28/2019 Introduction to ANSYS Workbench
29/29