INTEROPERABILITY REPORT Ascom i62 Cisco WLC ......Interoperability Report - Ascom i62 – Cisco WLC AP1830/1850. 6 2016-05-18 Known issues and limitations - Important.It is essential

Interoperability Report - Ascom i62 – Cisco WLC AP1830/1850. 1 2016-05-18

INTEROPERABILITY REPORT Ascom i62 Cisco WLC plattform. AP 1830 & 1850 Cisco WLC Version 8.1.131

Ascom i62 and OEM derivatives 5.5.0

Ascom, Gothenburg

May 2016

[ ]


TABLE OF CONTENT: INTRODUCTION ........................................................................................................................... 3

About Ascom ............................................................................................................................ 3 About Cisco .............................................................................................................................. 3

SITE INFORMATION .................................................................................................................... 4 SUMMARY AND TEST RESULTS ................................................................................................ 5

Known issues and limitations .................................................................................................... 6 Compatibility information .......................................................................................................... 6 General conclusion ................................................................................................................... 6

APPENDIX A: TEST CONFIGURATIONS .................................................................................... 7 Cisco WLC 5508 Version 8.1.131 ............................................................................................. 7

Security settings (PSK) ......................................................................................................... 7 802.1X authentication (PEAP-MSCHAPv2). ......................................................................... 9 EAP-FAST using an internal authentication server. ............................................................ 11 General settings (QoS, Radio) ............................................................................................ 14

Ascom i62 ............................................................................................................................... 21 Innovaphone IP6000 (IP PBX) ................................................................................................ 23

APPENDIX B: DETAILED TEST RECORDS .............................................................................. 24


INTRODUCTION This document describes necessary steps and guidelines to optimally configure the Cisco WLC platform with Ascom i62 VoWiFi handsets.

The guide should be used in conjunction with both Cisco and Ascoms configuration guide(s).

About Ascom Ascom Wireless Solutions (www.ascom.com/ws) is a leading provider of innovative communication solutions providing integrated workflow intelligence for hospitals, senior care, and independent living, and other business areas where mission-critical communication is essential. Approximately 100 000 systems are installed globally. The company offers a broad range of voice and professional messaging solutions, creating value for customers by supporting and optimizing their mission-critical communication processes. The solutions are based on Cellular, VoWiFi, IP-DECT, Nurse call and Paging technologies, smartly integrated via Ascom Unite into existing enterprise systems. The company has subsidiaries in 13 countries and 1,200 employees worldwide. Founded in 1955 and based in Göteborg, Sweden, Ascom Wireless Solutions is part of the Ascom Group, listed on the Swiss Stock Exchange (ASCN:SIX).

About Cisco Cisco (NASDAQ: CSCO) is the worldwide leader in IT that helps companies seize the opportunities of tomorrow by proving that amazing things can happen when you connect the previously unconnected. For ongoing news, please go to http://thenetwork.cisco.com.


SITE INFORMATION

Test Site: Ascom US 300 Perimeter park drive Morrisville, NC, US-27560 USA Participants: Karl-Magnus Olsson, Ascom HQ, Gothenburg Sweden TEST TOPOLOGY


SUMMARY AND TEST RESULTS Please refer to Appendix B for detailed results. WLAN Controller Features

High Level Functionality Result Association, Open with No Encryption OK Association, WPA2-PSK, AES Encryption OK Association, PEAP-MSCHAPv2 Auth., AES Encryption OK Association with EAP-FAST authentication OK Association, EAP-TLS OK Association, Multiple ESSIDs OK Beacon Interval and DTIM Period OK PMKSA Caching OK* WPA2-opportunistic/proactive Key Caching OK* WMM Prioritization OK Active Mode (load test) OK 802.11 Power-save mode OK 802.11e U-APSD OK 802.11e U-APSD (load test) OK *) Enabled by default Roaming

High Level Functionality Result Roaming, Open with No Encryption OK (typical roaming time 28ms) * Roaming, WPA2-PSK, AES Encryption OK (Typical roaming time 28ms)* Roaming, PEAP-MSCHAPv2 Auth, AES Encryption OK (Typical roaming time 48ms)* /** Roaming, EAP-FAST, CCKM OK (Typical roaming time 38ms)* *) Average roaming times are measured using 802.11a/n. Refer to Appendix B for detailed test results * *) Measured times is with opportunistic/proactive Key Caching enabled (default enabled)


Known issues and limitations

- Important. It is essential to follow the “General guidelines when deploying Ascom i62 handsets in 802.11a/n/ac environments” on page 16 and not exceed 8 enabled channels in the system. Not doing so might cause the Ascom i62 to randomly lose connection to the network for a few seconds (“no network” including audible signal)

- Note that Cisco AP 1830 and 1850 does not support CCX and DTPC. Refer to Cisco release notes for additional information.

For additional information regarding the known issues please contact [email protected] or [email protected]

Compatibility information Supported access points with Cisco WLC version 8.1.131: AP 1830 and 1850 Supported controller platforms with Cisco WLC version 8.1.131: 2500 series WLC 5500 series WLC WISM2 (Wireless services module) Cisco Flex 7500 /8500 controllers

General conclusion Overall the outcome of interoperability verification, including association, authentication and roaming produced very good results. If U-APSD shall be used in the handset it is very important that the WMM parameters in the Cisco WLC are set correctly since U-APSD handles a bi-directional data stream where the up and downlink must be transmitted within the same EDCA Access Category. To use U-APSD, make sure to set QoS to Platinum for the current WLAN profile and set WMM to “Required”. Also set EDCA profile for 802.11b/g/n and 802.11a/n/ac to "Voice Optimized" and disable low latency MAC.


APPENDIX A: TEST CONFIGURATIONS

Cisco WLC 5508 Version 8.1.131 In the following chapter you will find screenshots and explanations of basic settings in order to get a Cisco WLC WLAN system to operate with an Ascom i62. Please note that security settings were modified according to requirements in individual test cases.

Security settings (PSK) Example of how to configure the system for PSK (WPA2-AES)

Security profile WPA2-PSK, AES encryption


Select PSK and enter a key (Here in ASCII format)


802.1X authentication (PEAP-MSCHAPv2). Example of how to configure the system for .1X authentication

Configuration of authentication using external Radius sever, 802.1X (Step 1). In this example is WPA2-AES/CCMP used.


Example of authentication configuration using external Radius sever (Step 2). Select the server to use. The server is configured under tab Security/Radius. See configuration of server below.

Configuration of authentication using external Radius sever (Step 3). The IP address and the secret must correspond to the IP and the credential used by the Radius server. Tests were performed using Cisco ACS as RADIUS server. Note. Depending authentication method used it might be necessary to add a certificate into the i62. PEAP-MSCHAPv2 requires a CA certificate and EAP-TLS requires both a CA certificate and a client certificate. Server certificate validation can be overridden in version 4.1.12 and above per handset setting. Note. Refer to the i62 section in Appendix A for matching handset configurations.


EAP-FAST using an internal authentication server.

Configuration of authentication using internal Radius sever and EAP-FAST (Step 1). In this example is WPA2-AES/CCMP used. Note. To use CCKM, replace 802.1X with CCKM check box. The “security mode” in the i62 has to be set to “Advanced” and CCKM has to be selected as “Authentication Key Management” instead of the default 802.1X.


Configuration of authentication using internal Radius sever and EAP-FAST (Step 2). Check the box “Local EAP Authentication” and choose your local EAP profile (created in step 4).

Configuration of authentication using internal Radius sever and EAP-FAST (Step 3). Create a local user and assign a password.


Configuration of authentication using internal Radius sever and EAP-FAST (Step 3). Create a local EAP profile and choose the EAP method to use.


General settings (QoS, Radio)

Set QoS to “Platinum (Voice)”

Make sure that WMM policy is set to “Required”


Disable “coverage Hole Detection” and “Session timeout”. Set DTIM period to Ascom recommended value 5. DTIM value 5 values are recommended in order to allow maximum battery conservation without impacting the quality. Using a lower DTIM value is possible but will reduce the standby time slightly.

Channel configuration. See next picture for additional information.


Ascom recommended settings for 802.11b/g/n are to only use channel 1, 6 and 11. For 802.11a/n/ac use channels according to the infrastructure manufacturer, country regulations and per guidelines below. Note that Tx power level and channel was manually set for test purpose. General guidelines when deploying Ascom i62 handsets in 802.11a/n/ac environments:

1. Enabling more than 8 channels will degrade roaming performance. Ascom recommends against going above this limit.

2. Using 40 MHz channels (or “channel-bonding”) will reduce the number of non-DFS* channels to two in ETSI regions (Europe). In FCC regions (North America), 40MHz is a more viable option because of the availability of additional non-DFS channels. The handset can co-exist with 40MHz stations in the same ESS.

3. Ascom do support and can coexist in 80MHz channel bonding environments. The recommendations is however to avoid 80MHz channel bonding as it severely reduces the number of available non overlapping channels.

4. Make sure that all non-DFS channel are taken before resorting to DFS channels. The handset can cope in mixed non-DFS and DFS environments; however, due to “unpredictability” introduced by radar detection protocols, voice quality may become distorted and roaming delayed. Hence Ascom recommends if possible avoiding the use of DFS channels in VoWIFI deployments.

*) Dynamic Frequency Selection (radar detection)


The default data rate set will work just fine, however Ascom recommends disabling the lowest speeds and have 12Mbits as lowest supported speed.

As Ascom i62 do support Channel Switch Announcement it’s recommended to have this setting enabled in the system (only applicable when DFS channels are used)


Ascom does support both usage of “11n Mode” and “11ac Mode” including 40 MHz and 80MHz channels Note. Follow the recommendations “General guidelines when deploying Ascom i62 handsets in 802.11a/n/ac environments“ on Page 17

The default data rate set will work just fine, however Ascom recommends disabling the lowest speeds and have 12Mbits as lowest supported speed. To further optimize performance it is recommended to disallow 802.11b clients to associate by setting 12Mbps rate to mandatory in 802.11g configuration.


Ascom recommends “EDCA Profile”: Voice Optimized and latency MAC to be disabled. (Both 802.11a/n/ac and 802.11b/g/n) Note. Using EDCA Profile “WMM” is possible but “Voice Optimized” is to prefer when voice clients are present in the system.

Depending on the infrastructure (switches) ”Protocol Type” may have to be disabled.


Cisco Configuration file See attached file (Running config.log) for complete Cisco WLC configuration.


Ascom i62

Network settings for WPA2-PSK Note. Make sure that the enabled channels in the i62 handset match the channel plan used in the system. Note. FCC is no longer allowing 802.11d to determine regulatory domain. Devices deployed in USA must set Regulatory domain to “USA”.


Network settings for .1X authentication (PEAP-MSCHAPv2)

802.1X Authentication requires a CA certificate to be uploaded to the phone by “right clicking” - > Edit certificates. EAP-TLS will require both a CA and a client certificate. Note that both a CA and a client certificate are needed for TLS. Otherwise only a CA certificate is needed. Server certificate validation can be overridden in version 4.1.12 and above per handset setting.


Innovaphone IP6000 (IP PBX) The Innovaphone IP6000 was configured with a static IP address of 192.168.0.50. Signaling is less relevant here since testing homes in on interoperability in relation to the WLAN infrastructure and not features of the IP PBX. During the tests the IP6000 also was used as DHCP server. IP6000 configuration: See attached file (complete-IP6000-08-03-a6.txt) for IP6000 configuration


APPENDIX B: DETAILED TEST RECORDS VoWIFI Pass 22 Fail 0 Comments 0 Untested 1 Total 23 See attached files for each AP model (WLANinteroperabilityTestReport_18xx i62.xls) for detailed test results. Please refer to the test specification for WLAN systems on Ascom’s interoperability web page for explicit information regarding each test case. See URL (requires login): https://www.ascom-ws.com/AscomPartnerWeb/en/startpage/Sales-tools/Interoperability


Document History Rev Date Author DescriptionPA 2016-01-29 SEKMO WLC version 8.1.131 Draft1 R1 2016-02-19 SEKMO Updates after review. Revision R1 R2 2016-05-13 SEKMO Regression test i62 v 5.5.0 and updates to “Known issues”

chapter

WLAN TR

WLAN Interoperability Test ReportWLAN configuration:

Beacon Interval: 100ms

Test object - Handset:DTIM Interval: 5

Ascom i62 5.5.0802.11d Regulatory Domain: World

Test object - WLAN system:WMM Enabled (Auto/WMM)

Cisco WLC 5508, Version 8.1.131No Auto-tune

AP 1820, 1850AP1850AP1830Single Voice VLAN

2.4Ghz5.0Ghz2.4Ghz5.0Ghz

Test CaseDescriptionVerdictVerdictVerdictVerdictComment

TEST AREA ASSOCIATION / AUTHENTICATION

#101Association with open authentication, no encryptionPASSPASSPASSPASS

#107Association with WPA2-PSK authentication, AES-CCMP encryptionPASSPASSPASSPASS

#110Association with PEAP-MSCHAPv2 auth, AES-CCMP encryptionPASSPASSPASSPASSCisco ACS RADIUS server; RootCA loaded on device;FAIL

#111Association with EAP-FAST authenticationPASSPASSPASSPASSCisco ACS RADIUS server and WLC internal RADIUS Server

#116Association with EAP-TLS authenticationPASSPASSPASSPASSCisco ACS RADIUS server; RootCA land client certificate loaded on device;

TEST AREA POWER-SAVE AND QOSPASS

#150802.11 Power-save modePASSPASSPASSPASSFAIL

#151Beacon period and DTIM intervalPASSPASSPASSPASSDTIM 1,3 5 , Beacon Period 100tuNOT TESTED

#152802.11e U-APSDPASSPASSPASSPASSSee Comment

#202WMM prioritizationPASSPASSPASSPASSiperf used to gernarate load.

TEST AREA "PERFORMANCE"

#308Power-save mode U-APSD – WPA2-PSKPASSPASSPASSPASS12hs ok on one single radio. Note that 12 was not the limit.

#310CAC - TSPECSee CommentSee CommentSee CommentSee CommentBahviour not optimal. Not noticable to user.

TEST AREA ROAMING AND HANDOVER TIMES

#401Handover with open authentication and no encryptionPASSPASSPASSPASSAVG roaming time 11an: 28ms, bgn: 35ms (No significat difference seen in roaming times between different AP models)

#404Handover with WPA2-PSK auth and AES-CCMP encryptionPASSPASSPASSPASSAVG roaming time 11an: 28ms, bgn: 39ms (No significat difference seen in roaming times between different AP models)

#408Handover with PEAP-MSCHAPv2 authentication and AES-CCMP encryptionPASSPASSPASSPASSAVG roaming time 11an: 48ms, bgn: 52ms (No significat difference seen in roaming times between different AP models)

#409Handover with EAP-FAST authentication with CCKMPASSPASSPASSPASSAVG roaming time 11an: 34ms, bgn: 38ms (No significat difference seen in roaming times between different AP models)

#411Handover using PMKSA and opportunistic/proactive key cachingPASSPASSPASSPASS

TEST AREA BATTERY LIFETIME

#501Battery lifetime in idlePASSPASSPASSPASS80-100hours.

#504Battery lifetime in call with power save mode U-APSDPASSPASSPASSPASS13-15h

TEST AREA STABILITY

#602Duration of call – U-APSD modePASSPASSPASSPASS24h call maintained

TEST AREA 802.11n

#801Frame aggregation A-MSDUNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#802Frame aggregation A-MPDUPASSPASSPASSPASSUplink and downlink.

#80440Mhz channelsNOT TESTEDPASSNOT TESTEDPASSonly 20MHz channel width tested on 2.4GHz band

#805802.11n ratesPASSPASSPASSPASS

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.02.19 10:45:01 =~=~=~=~=~=~=~=~=~=~=~=ena� �� ru� �� show run?run-config running-config (Cisco Controller) >show runn� �ning-config

Notice: "show running-config" has been changed to be an alias to "show run-config".Use "show run-config commands" to display the configuration commands.Press Enter to continue or to abort...System Inventory

NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"

PID: AIR-CT5508-K9, VID: V01, SN: FCW1444L002

Burned-in MAC Address............................ F8:66:F2:FA:75:A0Power Supply 1................................... Present, OKPower Supply 2................................... AbsentMaximum number of APs supported.................. 500Press Enter to continue or to abort

System InformationManufacturer's Name.............................. Cisco Systems Inc.Product Name..................................... Cisco ControllerProduct Version.................................. 8.1.131.0Bootloader Version............................... 1.0.1Field Recovery Image Version..................... 6.0.182.0Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27Build Type....................................... DATA + WPS

System Name...................................... Cisco_fa:75:a4System Location.................................. System Contact................................... System ObjectID.................................. 1.3.6.1.4.1.9.1.1069Redundancy Mode.................................. DisabledIP Address....................................... 192.168.0.15IPv6 Address..................................... ::Last Reset....................................... Power on resetSystem Up Time................................... 24 days 2 hrs 54 mins 36 secsSystem Timezone Location......................... System Stats Realtime Interval................... 5System Stats Normal Interval..................... 180

Configured Country............................... Multiple Countries:SE,US

--More or (q)uit current module or to abortOperating Environment............................ Commercial (0 to 40 C)Internal Temp Alarm Limits....................... 0 to 65 CInternal Temperature............................. +38 CExternal Temperature............................. +25 CFan Status....................................... OK

State of 802.11b Network......................... EnabledState of 802.11a Network......................... EnabledNumber of WLANs.................................. 7Number of Active Clients......................... 0Burned-in MAC Address............................ F8:66:F2:FA:75:A0Power Supply 1................................... Present, OKPower Supply 2................................... AbsentMaximum number of APs supported.................. 500System Nas-Id.................................... Cisco_fa:75:a4WLC MIC Certificate Types........................ SHA1Press Enter to continue or to abort

System Time Information:

Time............................................. Fri Feb 19 10:52:03 2016

Timezone delta................................... 0:0Timezone location................................

NTP Servers NTP Polling Interval......................... 86400

Index NTP Key Index NTP Server NTP Msg Auth Status ------- ----------------------------------------------------------------------------------

Press Enter to continue or to abort

Redundancy InformationRedundancy Mode ................................. SSO DISABLED Local State...................................... ACTIVEPeer State....................................... N/A Unit............................................. PrimaryUnit ID.......................................... F8:66:F2:FA:75:A0Redunadancy State................................ N/A Mobility MAC..................................... F8:66:F2:FA:75:A0Redundancy Management IP Address................. 0.0.0.0Peer Redundancy Management IP Address............ 0.0.0.0Redundancy Port IP Address....................... 0.0.0.0Peer Redundancy Port IP Address.................. 169.254.0.0Press Enter to continue or to abort

AP Bundle Information

Primary AP ImageSize--------------------ap1g112572ap1g211696ap1g313580ap1g414792ap3g19696ap3g213452ap3g30ap8017984ap8029468c11408588c15207304c15509636c157011656c602i3864version.info4

Secondary AP ImageSize----------------------

--More or (q)uit current module or to abortap1g112572ap1g211688ap1g313580ap1g414680ap3g19696ap3g213440ap3g30ap8017984ap8029468c11408588c15207292c15509636c157011656c602i3864version.info4Press Enter to continue or to abort

Switch Configuration802.3x Flow Control Mode......................... Disable FIPS prerequisite features....................... DisabledWLANCC prerequisite features..................... DisabledUCAPL prerequisite features...................... DisabledDTLS WLC MIC .................................... SHA2secret obfuscation............................... EnabledStrong Password Check Features case-check.................................... Enabled consecutive-check............................. Enabled default-check................................. Enabled username-check................................ Enabled position-check................................ Disabled case-digit-check.............................. Disabled Min. Password length.......................... 3 Min. Upper case chars......................... 0 Min. Lower case chars......................... 0 Min. Digits chars............................. 0 Min. Special chars............................ 0Mgmt User Password Lifetime [days]...................... 0 Password Lockout.............................. Disabled

--More or (q)uit current module or to abort Lockout Attempts.............................. 0 Lockout Timeout [mins]........................ 0SNMPv3 User Password Lifetime [days]...................... 0 Password Lockout.............................. Disabled Lockout Attempts.............................. 3 Lockout Timeout [mins]........................ 5Press Enter to continue or to abort

Network InformationRF-Network Name............................. ascomDNS Server IP............................... Web Mode.................................... DisableSecure Web Mode............................. EnableSecure Web Mode Cipher-Option High.......... DisableSecure Web Mode Cipher-Option SSLv2......... DisableSecure Web Mode RC4 Cipher Preference....... DisableSecure Web Mode SSL Protocol................ DisableOCSP........................................ DisabledOCSP responder URL.......................... Secure Shell (ssh).......................... EnableSecure Shell (ssh) Cipher-Option High....... DisableTelnet...................................... DisableEthernet Multicast Forwarding............... DisableEthernet Broadcast Forwarding............... DisableIPv4 AP Multicast/Broadcast Mode............ UnicastIPv6 AP Multicast/Broadcast Mode............ UnicastIGMP snooping............................... DisabledIGMP timeout................................ 60 secondsIGMP Query Interval......................... 20 secondsMLD snooping................................ Disabled

--More or (q)uit current module or to abortMLD timeout................................. 60 secondsMLD query interval.......................... 20 secondsUser Idle Timeout........................... 300 secondsARP Idle Timeout............................ 300 secondsCisco AP Default Master..................... DisableAP Join Priority............................ DisableMgmt Via Wireless Interface................. EnableMgmt Via Dynamic Interface.................. DisableBridge MAC filter Config.................... EnableBridge Security Mode........................ EAPMesh Full Sector DFS........................ EnableMesh Backhaul RRM........................... DisableAP Fallback ................................ EnableWeb Auth CMCC Support ...................... DisabledWeb Auth Redirect Ports .................... 80Web Auth Proxy Redirect ................... DisableWeb Auth Captive-Bypass .................. DisableWeb Auth Secure Web ....................... EnableWeb Auth Secure Redirection ............... DisableFast SSID Change ........................... DisabledAP Discovery - NAT IP Only ................. EnabledIP/MAC Addr Binding Check .................. EnabledLink Local Bridging Status ................. Disabled

--More or (q)uit current module or to abortCCX-lite status ............................ Disableoeap-600 dual-rlan-ports ................... Disableoeap-600 local-network ..................... Enableoeap-600 Split Tunneling (Printers)......... DisableWebPortal Online Client .................... 0WebPortal NTF_LOGOUT Client ................ 0mDNS snooping............................... DisabledmDNS Query Interval......................... 15 minutesWeb Color Theme............................. DefaultCapwap Prefer Mode.......................... IPv4Network Profile............................. DisabledClient ip conflict detection (DHCP) ........ DisabledMesh BH RRM ................................ DisableMesh Aggressive DCA......................... DisableMesh Auto RF................................ DisablePress Enter to continue or to abort

Port Summary STP Admin Physical Physical Link LinkPr Type Stat Mode Mode Status Status Trap POE SFPType -- ------- ---- ------- ---------- ---------- ------ ------- ------- ----------1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseSX 2 Normal Disa Enable Auto Auto Down Enable N/A Not Present 3 Normal Disa Enable Auto Auto Down Enable N/A Not Present 4 Normal Disa Enable Auto Auto Down Enable N/A Not Present 5 Normal Disa Enable Auto Auto Down Enable N/A Not Present 6 Normal Disa Enable Auto Auto Down Enable N/A Not Present 7 Normal Disa Enable Auto Auto Down Enable N/A Not Present 8 Normal Disa Enable Auto Auto Down Enable N/A Not Present Press Enter to continue or to abort

AP SummaryNumber of APs.................................... 1

Global AP User Name.............................. Not ConfiguredGlobal AP Dot1x User Name........................ Not Configured

AP Name Slots AP Model Ethernet MAC Location Country IP Address Clients DSE Location ------------------ ----- -------------------- ----------------- ---------------- ---------- --------------- -------- --------------AP7c0e.cefb.97d0 2 AIR-CAP3702I-A-K9 7c:0e:ce:fb:97:d0 default location US 192.168.0.145 0 [0 ,0 ,0 ]

AP Tcp-Mss-Adjust InfoAP Name TCP State MSS Size------------------ -------- ------- AP7c0e.cefb.97d0 disabled -Press Enter to continue or to abort

AP LocationTotal Number of AP Groups........................ 1

Site Name........................................ default-groupSite Description................................. NAS-identifier................................... Cisco_fa:75:a4Client Traffic QinQ Enable....................... FALSEDHCPv4 QinQ Enable............................... FALSEAP Operating Class............................... Not-configuredCapwap Prefer Mode............................... Not-configured

RF Profile----------2.4 GHz band..................................... 5 GHz band.......................................

WLAN ID Interface Network Admission Control Radio Policy------- ----------- -------------------------- ------------ 1 management Disabled None 2 management Disabled None 3 management Disabled None

--More or (q)uit current module or to abort 4 management Disabled None 5 management Disabled None 6 management Disabled None 7 management Disabled None

*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.

AP Name Slots AP Model Ethernet MAC Location Port Country Priority------------------ ----- ------------------- ----------------- ---------------- ---- ------- --------AP7c0e.cefb.97d0 2 AIR-CAP3702I-A-K9 7c:0e:ce:fb:97:d0 default location 1 US 1


RF Profile

Number of RF Profiles............................ 6

Out Of Box State................................. Disabled

Out Of Box Persistence........................... Disabled

RF Profile Name Band Description 11n-client-only Applied --------------------------------- ------- ----------------------------------- ------------------ ----------High-Client-Density-802.11a 5 GHz disable No High-Client-Density-802.11bg 2.4 GHz disable No Low-Client-Density-802.11a 5 GHz disable No Low-Client-Density-802.11bg 2.4 GHz disable No Typical-Client-Density-802.11a 5 GHz disable No Typical-Client-Density-802.11bg 2.4 GHz disable No

RF Profile name................................ High-Client-Density-802.11aDescription...................................... AP Group Name.................................... Radio policy..................................... 5 GHz

--More or (q)uit current module or to abort11n-client-only.................................. disabledTransmit Power Threshold v1...................... -65 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... 7 dBmMax Transmit Power............................... 30 dBm802.11a Operational Rates 802.11a 6M Rate.............................. Disabled 802.11a 9M Rate.............................. Disabled 802.11a 12M Rate............................. Mandatory 802.11a 18M Rate............................. Supported 802.11a 24M Rate............................. Supported 802.11a 36M Rate............................. Supported 802.11a 48M Rate............................. Supported 802.11a 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

--More or (q)uit current module or to abort

6 600

7 600

Trap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. -78 dBmCca Threshold.................................... 0 dBmSlot Admin State:................................ Enabled

Band Select Probe Response............................... Disabled Cycle Count.................................. 2 cycles Cycle Threshold.............................. 200 milliseconds Expire Suppression........................... 20 seconds Expire Dual Band............................. 60 seconds Client Rssi.................................. -80 dBm Client Mid Rssi.............................. -80 dBm

Load Balancing

--More or (q)uit current module or to abort Denial....................................... 3 count Window....................................... 5 clients

Coverage Data Data......................................... -80 dBm Voice........................................ -80 dBm Minimum Client Level......................... 3 clients Exception Level.............................. 25 %DCA Channel List................................. 36DCA Bandwidth.................................... 40DCA Foreign AP Contribution...................... enabled

802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled MCS-09 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-10 Rate.................................. enabled MCS-11 Rate.................................. enabled MCS-12 Rate.................................. enabled MCS-13 Rate.................................. enabled MCS-14 Rate.................................. enabled MCS-15 Rate.................................. enabled MCS-16 Rate.................................. enabled MCS-17 Rate.................................. enabled MCS-18 Rate.................................. enabled MCS-19 Rate.................................. enabled MCS-20 Rate.................................. enabled MCS-21 Rate.................................. enabled MCS-22 Rate.................................. enabled MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled

--More or (q)uit current module or to abortRF Profile name................................ High-Client-Density-802.11bgDescription...................................... AP Group Name.................................... Radio policy..................................... 2.4 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -70 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... 7 dBmMax Transmit Power............................... 30 dBm802.11b/g Operational Rates 802.11b/g 1M Rate............................ Disabled 802.11b/g 2M Rate............................ Disabled 802.11b/g 5.5M Rate.......................... Disabled 802.11b/g 11M Rate........................... Disabled 802.11g 6M Rate.............................. Disabled 802.11g 9M Rate.............................. Supported 802.11g 12M Rate............................. Mandatory 802.11g 18M Rate............................. Supported 802.11g 24M Rate............................. Supported 802.11g 36M Rate............................. Supported 802.11g 48M Rate............................. Supported 802.11g 54M Rate............................. SupportedMax Clients...................................... 200


WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

6 600

7 600

Trap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. -82 dBmCca Threshold.................................... 0 dBmSlot Admin State:................................ Enabled

Band Select Probe Response............................... Disabled

--More or (q)uit current module or to abort Cycle Count.................................. 2 cycles Cycle Threshold.............................. 200 milliseconds Expire Suppression........................... 20 seconds Expire Dual Band............................. 60 seconds Client Rssi.................................. -80 dBm Client Mid Rssi.............................. -80 dBm

Load Balancing Denial....................................... 3 count Window....................................... 5 clients

Coverage Data Data......................................... -80 dBm Voice........................................ -80 dBm Minimum Client Level......................... 3 clients Exception Level.............................. 25 %DCA Channel List................................. 1,6,11DCA Bandwidth.................................... 20DCA Foreign AP Contribution...................... enabled

802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled MCS-09 Rate.................................. enabled MCS-10 Rate.................................. enabled MCS-11 Rate.................................. enabled MCS-12 Rate.................................. enabled MCS-13 Rate.................................. enabled MCS-14 Rate.................................. enabled MCS-15 Rate.................................. enabled MCS-16 Rate.................................. enabled MCS-17 Rate.................................. enabled MCS-18 Rate.................................. enabled MCS-19 Rate.................................. enabled MCS-20 Rate.................................. enabled MCS-21 Rate.................................. enabled MCS-22 Rate.................................. enabled MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled

RF Profile name................................ Low-Client-Density-802.11aDescription...................................... AP Group Name.................................... Radio policy..................................... 5 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -60 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... -10 dBmMax Transmit Power............................... 30 dBm802.11a Operational Rates 802.11a 6M Rate.............................. Disabled 802.11a 9M Rate.............................. Disabled 802.11a 12M Rate............................. Mandatory 802.11a 18M Rate............................. Supported 802.11a 24M Rate............................. Supported

--More or (q)uit current module or to abort 802.11a 36M Rate............................. Supported 802.11a 48M Rate............................. Supported 802.11a 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

6 600

7 600

Trap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. -80 dBmCca Threshold.................................... 0 dBm

--More or (q)uit current module or to abortSlot Admin State:................................ Enabled





802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled MCS-09 Rate.................................. enabled MCS-10 Rate.................................. enabled MCS-11 Rate.................................. enabled MCS-12 Rate.................................. enabled MCS-13 Rate.................................. enabled MCS-14 Rate.................................. enabled MCS-15 Rate.................................. enabled MCS-16 Rate.................................. enabled MCS-17 Rate.................................. enabled MCS-18 Rate.................................. enabled MCS-19 Rate.................................. enabled MCS-20 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-21 Rate.................................. enabled MCS-22 Rate.................................. enabled MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled

RF Profile name................................ Low-Client-Density-802.11bgDescription...................................... AP Group Name.................................... Radio policy..................................... 2.4 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -65 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... -10 dBmMax Transmit Power............................... 30 dBm802.11b/g Operational Rates 802.11b/g 1M Rate............................ Disabled

--More or (q)uit current module or to abort 802.11b/g 2M Rate............................ Disabled 802.11b/g 5.5M Rate.......................... Disabled 802.11b/g 11M Rate........................... Mandatory 802.11g 6M Rate.............................. Disabled 802.11g 9M Rate.............................. Disabled 802.11g 12M Rate............................. Supported 802.11g 18M Rate............................. Supported 802.11g 24M Rate............................. Supported 802.11g 36M Rate............................. Supported 802.11g 48M Rate............................. Supported 802.11g 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

6 600

7 600

--More or (q)uit current module or to abortTrap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. -85 dBmCca Threshold.................................... 0 dBmSlot Admin State:................................ Enabled



--More or (q)uit current module or to abortCoverage Data Data......................................... -90 dBm Voice........................................ -90 dBm Minimum Client Level......................... 3 clients Exception Level.............................. 25 %DCA Channel List................................. 1,6,11DCA Bandwidth.................................... 20DCA Foreign AP Contribution...................... enabled

802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled MCS-09 Rate.................................. enabled MCS-10 Rate.................................. enabled MCS-11 Rate.................................. enabled MCS-12 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-13 Rate.................................. enabled MCS-14 Rate.................................. enabled MCS-15 Rate.................................. enabled MCS-16 Rate.................................. enabled MCS-17 Rate.................................. enabled MCS-18 Rate.................................. enabled MCS-19 Rate.................................. enabled MCS-20 Rate.................................. enabled MCS-21 Rate.................................. enabled MCS-22 Rate.................................. enabled MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled

RF Profile name................................ Typical-Client-Density-802.11aDescription...................................... AP Group Name....................................

--More or (q)uit current module or to abortRadio policy..................................... 5 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -70 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... -10 dBmMax Transmit Power............................... 30 dBm802.11a Operational Rates 802.11a 6M Rate.............................. Disabled 802.11a 9M Rate.............................. Disabled 802.11a 12M Rate............................. Mandatory 802.11a 18M Rate............................. Supported 802.11a 24M Rate............................. Supported 802.11a 36M Rate............................. Supported 802.11a 48M Rate............................. Supported 802.11a 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600


5 600

6 600

7 600

Trap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. AUTOCca Threshold.................................... 0 dBmSlot Admin State:................................ Enabled


--More or (q)uit current module or to abortLoad Balancing Denial....................................... 3 count Window....................................... 5 clients


802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled



RF Profile name................................ Typical-Client-Density-802.11bgDescription...................................... AP Group Name.................................... Radio policy..................................... 2.4 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -70 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... -10 dBmMax Transmit Power............................... 30 dBm802.11b/g Operational Rates 802.11b/g 1M Rate............................ Disabled 802.11b/g 2M Rate............................ Disabled 802.11b/g 5.5M Rate.......................... Disabled 802.11b/g 11M Rate........................... Disabled 802.11g 6M Rate.............................. Disabled 802.11g 9M Rate.............................. Supported 802.11g 12M Rate............................. Mandatory 802.11g 18M Rate............................. Supported 802.11g 24M Rate............................. Supported 802.11g 36M Rate............................. Supported 802.11g 48M Rate............................. Supported 802.11g 54M Rate............................. Supported

--More or (q)uit current module or to abortMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

6 600

7 600

Trap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. AUTOCca Threshold.................................... 0 dBmSlot Admin State:................................ Enabled

Band Select

--More or (q)uit current module or to abort Probe Response............................... Disabled Cycle Count.................................. 2 cycles Cycle Threshold.............................. 200 milliseconds Expire Suppression........................... 20 seconds Expire Dual Band............................. 60 seconds Client Rssi.................................. -80 dBm Client Mid Rssi.............................. -80 dBm


Coverage Data Data......................................... -80 dBm Voice........................................ -80 dBm Minimum Client Level......................... 3 clients Exception Level.............................. 25 %DCA Channel List................................. 1,6,11DCA Bandwidth.................................... 20DCA Foreign AP Contribution...................... enabled

802.11n MCS Rates MCS-00 Rate.................................. enabled


--More or (q)uit current module or to abort MCS-24 Rate.................................. enabled MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabledPress Enter to continue or to abort

AP ConfigCisco AP Identifier.............................. 6Cisco AP Name.................................... AP7c0e.cefb.97d0Country code..................................... Multiple Countries:SE,USRegulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-ABEAP Country code.................................. US - United StatesAP Regulatory Domain............................. -ASwitch Port Number .............................. 1MAC Address...................................... 7c:0e:ce:fb:97:d0IP Address Configuration......................... DHCPIP Address....................................... 192.168.0.145IP NetMask....................................... 255.255.255.0Gateway IP Addr.................................. 192.168.0.50NAT External IP Address.......................... NoneCAPWAP Path MTU.................................. 1485Telnet State..................................... Globally DisabledSsh State........................................ Globally DisabledCisco AP Location................................ default locationCisco AP Floor Label............................. 0Cisco AP Group Name.............................. default-groupPrimary Cisco Switch Name........................ Primary Cisco Switch IP Address.................. Not Configured

--More or (q)uit current module or to abortSecondary Cisco Switch Name...................... Secondary Cisco Switch IP Address................ Not ConfiguredTertiary Cisco Switch Name....................... Tertiary Cisco Switch IP Address................. Not ConfiguredAdministrative State ............................ ADMIN_ENABLEDOperation State ................................. REGISTEREDMirroring Mode .................................. DisabledAP Mode ......................................... LocalPublic Safety ................................... Disabled ATF Mode: ....................................... DisableAP SubMode ...................................... Not ConfiguredRogue Detection ................................. EnabledRemote AP Debug ................................. DisabledLogging trap severity level ..................... informationalLogging syslog facility ......................... systemS/W Version .................................... 8.1.131.0Boot Version ................................... 15.2.4.0Mini IOS Version ................................ 7.6.1.118Stats Reporting Period .......................... 180Stats Collection Mode ........................... normalLED State........................................ EnabledPoE Pre-Standard Switch.......................... DisabledPoE Power Injector MAC Addr...................... Disabled

--More or (q)uit current module or to abortPower Type/Mode.................................. Power injector / Normal modeNumber Of Slots.................................. 2 AP Model......................................... AIR-CAP3702I-A-K9AP Image......................................... C3700-K9W8-MIOS Version...................................... 15.3(3)JBB6$Reset Button..................................... EnabledAP Serial Number................................. FTX1832R34MAP Certificate Type.............................. Manufacture InstalledAP LAG Configuration Status ..................... DisabledLAG Support for AP .............................. NoAP User Mode..................................... AUTOMATICAP User Name..................................... CiscoAP Dot1x User Mode............................... Not ConfiguredAP Dot1x User Name............................... Not ConfiguredCisco AP system logging host..................... 255.255.255.255AP Up Time....................................... 11 days, 00 h 44 m 25 sAP LWAPP Up Time................................. 11 days, 00 h 42 m 25 sJoin Date and Time............................... Mon Feb 8 10:09:39 2016Join Taken Time.................................. 0 days, 00 h 01 m 59 s

Attributes for Slot 0 Radio Type................................... RADIO_TYPE_80211n-2.4 Administrative State ........................ ADMIN_ENABLED

--More or (q)uit current module or to abort Operation State ............................. UP Radio Role .................................. ACCESS Radio Mode .................................. Local CellId ...................................... 0

Station Configuration Configuration ............................. AUTOMATIC Number Of WLANs ........................... 4 Medium Occupancy Limit .................... 100 CFP Period ................................ 4 CFP MaxDuration ........................... 60 BSSID ..................................... f0:7f:06:02:34:40 Operation Rate Set 11000 Kilo Bits.......................... MANDATORY 12000 Kilo Bits.......................... SUPPORTED 18000 Kilo Bits.......................... SUPPORTED 24000 Kilo Bits.......................... SUPPORTED 36000 Kilo Bits.......................... SUPPORTED 48000 Kilo Bits.......................... SUPPORTED 54000 Kilo Bits.......................... SUPPORTED MCS Set MCS 0.................................... SUPPORTED MCS 1.................................... SUPPORTED

--More or (q)uit current module or to abort MCS 2.................................... SUPPORTED MCS 3.................................... SUPPORTED MCS 4.................................... SUPPORTED MCS 5.................................... SUPPORTED MCS 6.................................... SUPPORTED MCS 7.................................... SUPPORTED MCS 8.................................... SUPPORTED MCS 9.................................... SUPPORTED MCS 10................................... SUPPORTED MCS 11................................... SUPPORTED MCS 12................................... SUPPORTED MCS 13................................... SUPPORTED MCS 14................................... SUPPORTED MCS 15................................... SUPPORTED MCS 16................................... SUPPORTED MCS 17................................... SUPPORTED MCS 18................................... SUPPORTED MCS 19................................... SUPPORTED MCS 20................................... SUPPORTED MCS 21................................... SUPPORTED MCS 22................................... SUPPORTED MCS 23................................... SUPPORTED MCS 24................................... DISABLED

--More or (q)uit current module or to abort MCS 25................................... DISABLED MCS 26................................... DISABLED MCS 27................................... DISABLED MCS 28................................... DISABLED MCS 29................................... DISABLED MCS 30................................... DISABLED MCS 31................................... DISABLED Beacon Period ............................. 100 Fragmentation Threshold ................... 2346 Multi Domain Capability Implemented ....... TRUE Multi Domain Capability Enabled ........... TRUE Country String ............................ US

Multi Domain Capability Configuration ............................. AUTOMATIC First Chan Num ............................ 1 Number Of Channels ........................ 11

MAC Operation Parameters Configuration ............................. AUTOMATIC Fragmentation Threshold ................... 2346 Packet Retry Limit ........................ 64

--More or (q)uit current module or to abort Tx Power Num Of Supported Power Levels ............. 8 Tx Power Level 1 .......................... 23 dBm Tx Power Level 2 .......................... 20 dBm Tx Power Level 3 .......................... 17 dBm Tx Power Level 4 .......................... 14 dBm Tx Power Level 5 .......................... 11 dBm Tx Power Level 6 .......................... 8 dBm Tx Power Level 7 .......................... 5 dBm Tx Power Level 8 .......................... 2 dBm Tx Power Configuration .................... CUSTOMIZED Current Tx Power Level .................... 4 Tx Power Assigned By ...................... User

Phy OFDM parameters Configuration ............................. CUSTOMIZED Current Channel ........................... 1 Channel Assigned By ....................... User Extension Channel ......................... NONE Channel Width.............................. 20 Mhz Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11 TI Threshold .............................. -50 DCA Channel List........................... Global

--More or (q)uit current module or to abort Legacy Tx Beamforming Configuration ....... CUSTOMIZED Legacy Tx Beamforming ..................... ENABLED Antenna Type............................... INTERNAL_ANTENNA Internal Antenna Gain (in .5 dBi units).... 8 Diversity.................................. DIVERSITY_ENABLED 802.11n Antennas A....................................... ENABLED B....................................... ENABLED C....................................... ENABLED D....................................... ENABLED

Performance Profile Parameters Configuration ............................. CUSTOMIZED Interference threshold..................... 10 % Noise threshold............................ -70 dBm RF utilization threshold................... 80 % Data-rate threshold........................ 1000000 bps Client threshold........................... 12 clients Coverage SNR threshold..................... 15 dB Coverage exception level................... 25 % Client minimum exception level............. 3 clients Rogue Containment Information Containment Count............................ 0


CleanAir Management Information CleanAir Capable......................... Yes CleanAir Management Administration St.... Enabled CleanAir Management Operation State...... Down Rapid Update Mode........................ Off Spectrum Expert connection............... Enabled CleanAir NSI Key....................... 800A41A0054BAF150E46280CECA7C3D9 Spectrum Expert Connections counter.... 0 CleanAir Sensor State.................... Configured

Radio Extended Configurations Beacon period.............................. 100 milliseconds Beacon range............................... AUTO Multicast buffer........................... AUTO Multicast data-rate........................ AUTO RX SOP threshold........................... AUTO CCA threshold.............................. AUTO

Cisco AP Identifier.............................. 6Cisco AP Name.................................... AP7c0e.cefb.97d0Country code..................................... Multiple Countries:SE,USRegulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-ABE

--More or (q)uit current module or to abortAP Country code.................................. US - United StatesAP Regulatory Domain............................. -ASwitch Port Number .............................. 1MAC Address...................................... 7c:0e:ce:fb:97:d0IP Address Configuration......................... DHCPIP Address....................................... 192.168.0.145IP NetMask....................................... 255.255.255.0Gateway IP Addr.................................. 192.168.0.50NAT External IP Address.......................... NoneCAPWAP Path MTU.................................. 1485Telnet State..................................... Globally DisabledSsh State........................................ Globally DisabledCisco AP Location................................ default locationCisco AP Floor Label............................. 0Cisco AP Group Name.............................. default-groupPrimary Cisco Switch Name........................ Primary Cisco Switch IP Address.................. Not ConfiguredSecondary Cisco Switch Name...................... Secondary Cisco Switch IP Address................ Not ConfiguredTertiary Cisco Switch Name....................... Tertiary Cisco Switch IP Address................. Not ConfiguredAdministrative State ............................ ADMIN_ENABLEDOperation State ................................. REGISTERED

--More or (q)uit current module or to abortMirroring Mode .................................. DisabledAP Mode ......................................... LocalPublic Safety ................................... Disabled ATF Mode: ....................................... DisableAP SubMode ...................................... Not ConfiguredRogue Detection ................................. EnabledRemote AP Debug ................................. DisabledLogging trap severity level ..................... informationalLogging syslog facility ......................... systemS/W Version .................................... 8.1.131.0Boot Version ................................... 15.2.4.0Mini IOS Version ................................ 7.6.1.118Stats Reporting Period .......................... 180Stats Collection Mode ........................... normalLED State........................................ EnabledPoE Pre-Standard Switch.......................... DisabledPoE Power Injector MAC Addr...................... DisabledPower Type/Mode.................................. Power injector / Normal modeNumber Of Slots.................................. 2 AP Model......................................... AIR-CAP3702I-A-K9AP Image......................................... C3700-K9W8-MIOS Version...................................... 15.3(3)JBB6$Reset Button..................................... Enabled

--More or (q)uit current module or to abortAP Serial Number................................. FTX1832R34MAP Certificate Type.............................. Manufacture InstalledAP LAG Configuration Status ..................... DisabledLAG Support for AP .............................. NoAP User Mode..................................... AUTOMATICAP User Name..................................... CiscoAP Dot1x User Mode............................... Not ConfiguredAP Dot1x User Name............................... Not ConfiguredCisco AP system logging host..................... 255.255.255.255AP Up Time....................................... 11 days, 00 h 44 m 25 sAP LWAPP Up Time................................. 11 days, 00 h 42 m 25 sJoin Date and Time............................... Mon Feb 8 10:09:39 2016Join Taken Time.................................. 0 days, 00 h 01 m 59 s

Attributes for Slot 1 Radio Type................................... RADIO_TYPE_80211ac-5 Radio Subband................................ RADIO_SUBBAND_ALL Administrative State ........................ ADMIN_ENABLED Operation State ............................. UP Radio Role .................................. ACCESS Radio Mode .................................. Local CellId ...................................... 0

--More or (q)uit current module or to abort Station Configuration Configuration ............................. AUTOMATIC Number Of WLANs ........................... 4 Medium Occupancy Limit .................... 100 CFP Period ................................ 4 CFP MaxDuration ........................... 60 BSSID ..................................... f0:7f:06:02:34:40 Operation Rate Set 12000 Kilo Bits.......................... MANDATORY 18000 Kilo Bits.......................... SUPPORTED 24000 Kilo Bits.......................... SUPPORTED 36000 Kilo Bits.......................... SUPPORTED 48000 Kilo Bits.......................... SUPPORTED 54000 Kilo Bits.......................... SUPPORTED MCS Set MCS 0.................................... SUPPORTED MCS 1.................................... SUPPORTED MCS 2.................................... SUPPORTED MCS 3.................................... SUPPORTED MCS 4.................................... SUPPORTED MCS 5.................................... SUPPORTED MCS 6.................................... SUPPORTED MCS 7.................................... SUPPORTED

--More or (q)uit current module or to abort MCS 8.................................... SUPPORTED MCS 9.................................... SUPPORTED MCS 10................................... SUPPORTED MCS 11................................... SUPPORTED MCS 12................................... SUPPORTED MCS 13................................... SUPPORTED MCS 14................................... SUPPORTED MCS 15................................... SUPPORTED MCS 16................................... SUPPORTED MCS 17................................... SUPPORTED MCS 18................................... SUPPORTED MCS 19................................... SUPPORTED MCS 20................................... SUPPORTED MCS 21................................... SUPPORTED MCS 22................................... SUPPORTED MCS 23................................... SUPPORTED MCS 24................................... DISABLED MCS 25................................... DISABLED MCS 26................................... DISABLED MCS 27................................... DISABLED MCS 28................................... DISABLED MCS 29................................... DISABLED MCS 30................................... DISABLED

--More or (q)uit current module or to abort MCS 31................................... DISABLED 802.11ac MCS Set Nss=1: MCS 0-9 .......................... SUPPORTED Nss=2: MCS 0-9 .......................... SUPPORTED Nss=3: MCS 0-9 .......................... SUPPORTED Nss=4: MCS 0-7 .......................... DISABLED Beacon Period ............................. 100 Fragmentation Threshold ................... 2346 Multi Domain Capability Implemented ....... TRUE Multi Domain Capability Enabled ........... TRUE Country String ............................ US

Multi Domain Capability Configuration ............................. AUTOMATIC First Chan Num ............................ 36 Number Of Channels ........................ 21

MAC Operation Parameters Configuration ............................. AUTOMATIC Fragmentation Threshold ................... 2346 Packet Retry Limit ........................ 64

Tx Power

--More or (q)uit current module or to abort Num Of Supported Power Levels ............. 5 Tx Power Level 1 .......................... 15 dBm Tx Power Level 2 .......................... 12 dBm Tx Power Level 3 .......................... 9 dBm Tx Power Level 4 .......................... 6 dBm Tx Power Level 5 .......................... 3 dBm Tx Power Configuration .................... CUSTOMIZED Current Tx Power Level .................... 3 Tx Power Assigned By ...................... User

Phy OFDM parameters Configuration ............................. CUSTOMIZED Current Channel ........................... 36 Channel Assigned By ....................... User Extension Channel ......................... ABOVE Channel Width.............................. 40 Mhz Allowed Channel List....................... 36,40,44,48,52,56,60,64,100, ......................................... 104,108,112,116,132,136,140, ......................................... 149,153,157,161,165 TI Threshold .............................. -50 DCA Channel List........................... Global Legacy Tx Beamforming Configuration ....... CUSTOMIZED Legacy Tx Beamforming ..................... ENABLED

--More or (q)uit current module or to abort Antenna Type............................... INTERNAL_ANTENNA Internal Antenna Gain (in .5 dBi units).... 8 Diversity.................................. DIVERSITY_ENABLED 802.11n Antennas A....................................... ENABLED B....................................... ENABLED C....................................... ENABLED D....................................... ENABLED

Performance Profile Parameters Configuration ............................. CUSTOMIZED Interference threshold..................... 10 % Noise threshold............................ -70 dBm RF utilization threshold................... 80 % Data-rate threshold........................ 1000000 bps Client threshold........................... 12 clients Coverage SNR threshold..................... 15 dB Coverage exception level................... 25 % Client minimum exception level............. 3 clients Rogue Containment Information Containment Count............................ 0

CleanAir Management Information

--More or (q)uit current module or to abort CleanAir Capable......................... Yes CleanAir Management Administration St.... Enabled CleanAir Management Operation State...... Up Rapid Update Mode........................ Off Spectrum Expert connection............... Enabled CleanAir NSI Key....................... 800A41A0054BAF150E46280CECA7C3D9 Spectrum Expert Connections counter.... 0 CleanAir Sensor State.................... Configured

Radio Extended Configurations Beacon period.............................. 100 milliseconds Beacon range............................... AUTO Multicast buffer........................... AUTO Multicast data-rate........................ AUTO RX SOP threshold........................... AUTO CCA threshold.............................. AUTO



AP Airewave Director ConfigurationNumber Of Slots.................................. 2 AP Name.......................................... AP7c0e.cefb.97d0MAC Address...................................... 7c:0e:ce:fb:97:d0 Slot ID........................................ 0 Radio Type..................................... RADIO_TYPE_80211b/g Sub-band Type.................................. All Noise Information Noise Profile................................ PASSED Channel 1.................................... -90 dBm Channel 2.................................... -94 dBm Channel 3.................................... -92 dBm Channel 4.................................... -83 dBm Channel 5.................................... -94 dBm Channel 6.................................... -94 dBm Channel 7.................................... -90 dBm Channel 8.................................... -93 dBm Channel 9.................................... -77 dBm Channel 10................................... -96 dBm Channel 11................................... -88 dBm Interference Information Interference Profile......................... PASSED Channel 1.................................... -58 dBm @ 2 % busy

--More or (q)uit current module or to abort Channel 2.................................... -69 dBm @ 1 % busy Channel 3.................................... -128 dBm @ 0 % busy Channel 4.................................... -128 dBm @ 0 % busy Channel 5.................................... -128 dBm @ 0 % busy Channel 6.................................... -61 dBm @ 4 % busy Channel 7.................................... -128 dBm @ 0 % busy Channel 8.................................... -128 dBm @ 0 % busy Channel 9.................................... -128 dBm @ 0 % busy Channel 10................................... -128 dBm @ 0 % busy Channel 11................................... -69 dBm @ 1 % busy Load Information Load Profile................................. PASSED Receive Utilization.......................... 0 % Transmit Utilization......................... 0 % Channel Utilization.......................... 25 % Attached Clients............................. 0 clients Coverage Information Coverage Profile............................. PASSED Failed Clients............................... 0 clients Client Signal Strengths RSSI -100 dbm................................ 0 clients RSSI -92 dbm................................ 0 clients RSSI -84 dbm................................ 0 clients

--More or (q)uit current module or to abort RSSI -76 dbm................................ 0 clients RSSI -68 dbm................................ 0 clients RSSI -60 dbm................................ 0 clients RSSI

Documents

INTEROPERABILITY REPORT Ascom i62 Cisco WLC ......Interoperability Report - Ascom i62 – Cisco WLC AP1830/1850. 6 2016-05-18 Known issues and limitations - Important.It is essential