Upload
others
View
76
Download
2
Embed Size (px)
Citation preview
O;kolkf;d & izzz’kklfud foLrkj ijh{k.k fjiksVZ Lak[;k/No. : T- 1378/1905/2020
COMMERCIAL - ADMINISTRATIVE EXTENSION
TEST REPORT ekg/Month : March, 2020
FORCE MOTORS LIMITED, OX 25 ORCHARD DLX LT TRACTOR
INTERNATIONAL TRACTORS LIMITED, SONALIKA INTERNATIONAL DI-740 III CM
SERIES TRACTOR
Hkkjr ljdkj
d`f"k ,Oka fdlku dY;k.k ea=ky;
¼d`f"k] lgdkfjrk ,oa fdlku dY;k.k foHkkx] e'khuhdj.k ,oa izkS|ksfxdh izHkkx½
GOVERNMENT OF INDIA MINISTRY OF AGRICULTURE AND FARMERS WELFARE (Department of Agriculture, Cooperation & Farmers Welfare,
Mechanization & Technology Division)
dsUnzh; d`f"k e'khujh izf'k{k.k ,oa ijh{k.k laLFkku
VªSDVj uxj] cqnuh ¼e-iz-½ 466 445
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE (An ISO 9001: 2015 Certified Institute)
TRACTOR NAGAR, BUDNI (M.P.) 466 445
E-mail: [email protected], Web site: fmttibudni.gov.in Telephone: 07564-234729, 234743
Page 1 of 14
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 2 of 14
Month: March Test Report No. T- 1378/1905/2020 Year : 2020
GOVERNMENT OF INDIA
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE TRACTOR NAGAR, BUDNI (MADHYA PRADESH) 466445, INDIA
Email: [email protected] Web site: fmttibudni.gov.in
Telephone: 07564-234729, 234743
Manufacturer : M/s. International Tractors Limited, Vill.- Chak Gurjan, P.O.- Piplanwala, Jalandhar Road, Distt.- Hoshiarpur-146 022 (Punjab) India
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 3 of 14
Type of Test : COMMERCIAL (Administrative
Extension)
Test code/Procedure
:
IS: 5994-1998 (Reaffirmed in 2014) and IS: 12207-2019.
Period of Test
:
February 2020
Test Report No.
:
T- 1378/1905/2020
Month/Year
: March, 2020
i) The results reported in this report are observed values and no corrections have been applied for atmospheric and site conditions.
ii) The data given in this report pertain to the particular machine was submitted by applicant for test.
iii) The results presented in this report do not in any way attribute to the durability of the machine.
iv) This report should not be reproduced in part or full without prior permission of the Director, Central Farm Machinery Training and Testing Institute, Budni (M.P.).
v) This is a Administrative Extension test report and should be read in conjunction with the 1
st Batch Test Report of “International Tractors Limited, Sonalika
International DI-740 III CM Series” Tractor bearing test report No. T- 1230/1757/2019 released in March, 2019.
S E L E C T E D C O N V E R S I O N S
A B B R E V I A T I O N S
Sl. No
Units Conversion Factor
1 Force: apa As per applicant
1 kgf 9.80665 N TDC Top Dead Centre
2.20462 lbf IS Indian Standard
2 Power: LHS /RHS
Left Hand Side/ Right Hand Side
1 Mechanical horse power
1.01387 Metric horse power
Hg Mercury
745.7 W Temp. Temperature
1 Metric horse power
735.5 W N.R. Not recorded
1 kW 1.35962 Metric horse power
rpm Revolutions per minute
3 Pressure: O.D/I.D Outer diameter/ Inner diameter
1 psi 6.895 kPa N.A. Not available/Not applicable
1 kgf/cm2 98.067 kPa = 735.56 mm
of Hg PTO Power take-off
R.H. Relative Humidity
1 bar 100 kPa = 10 N/cm2
SIP Seat Index Point 1 mm of Hg 1.3332 m-bar
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 4 of 14
C O N T E N T S
PAGE
1. Scope of Test 05
2. Essential Tests 05
2.1 Specifications 05
3. Summary of Observations, Comments & Recommendations 09
4. Citizen Charter 14
5. Applicant’s Comments 14
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 5 of 14
1. SCOPE OF TEST
The “International Tractors Limited, Sonalika International DI-740 III CM Series” tractor had undergone “Commercial 1
st Batch Test” at this Institute vide test report No.
T-1230/1757/2019 was released in March, 2019. The performance results in Chapter-15 of said test report were evaluated on the basis of IS: 12207-2014.
Subsequently, the fourth revision of IS: 12207-2019 was established on dated 25th July,
2019. Therefore, the performance results of the said tractor has to be evaluated as per IS: 12207-2019. It was observed that, some of the parameters are not meeting the evaluative requirements applicable for “Qualifying Minimum Performance Criteria” as per clause-4 Table-1 of the said Indian Standard for acceptance of tractor for the purpose of subsidies / NABARD financing. The parameters which were not meeting the evaluative requirements has been modified & permanently incorporated in the production of said tractor model by the manufacturer.
Subsequently, the applicant has submitted the said model for inspection / test and
same has been tested / evaluated and are summarized under Chapter-3 of this test report.
The applicant has informed that modified parameters have been implemented from
tractor chassis number and engine serial number of tractor model “International Tractors
Limited, Sonalika International DI-740 III CM Series” generated on production line as
under tabulated:-
S. No. Parameters Modified Chassis Number Engine Number
1. Labelling plate
MZESH912583S3
3100ELI04B908045F3
2. Specification of linkage drawbar
3. Re-declaration of Maximum lifting capacity throughout the range of lift, at hitch points, (kN)
Manufacturer : M/s. International Tractors Limited, Vill.- Chak Gurjan, P.O.- Piplanwala, Jalandhar Road, Distt.- Hoshiarpur-146 022 (Punjab) India
Test requested by (Applicant) : The manufacturer
2. ESSENTIAL TESTS
2.1. SPECIFICATIONS
The following are the brief specifications of the tractor. However, for detail specifications of the tractor, the test report No. T-1230/1757/2019 was released in March, 2019 should be referred. 2.1.1 Tractor:
Make : International Tractors Limited Model : Sonalika international DI-740 III CM Series Type : Four wheeled, Rear wheel driven, Unit
construction, General purpose, Agricultural tractor
Month & Year of manufacture : 02 20
Chassis Serial number : MZESH912583S3 Country of Origin : India
2.1.2 Engine: Make : Sonalika Model : 3100ELI Type : Four stroke, liquid cooled, naturally aspirated,
direct injection diesel engine Serial number : 3100ELI04B908045F3
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 6 of 14
Engine speed (Manufacturer’s recommended production setting)(rpm) :
- Maximum speed at no load : 2150 to 2250
- Low idle speed : 600 to 700
- Speed at maximum torque : 1100 to 1300
Rated speed, (rpm):
- For PTO use : 2000
- For drawbar use : 2000
2.1.3 Cylinder & Cylinder Head:
Number : Three
Disposition : Vertical, Inline
Bore / stroke, (mm) : 100/ 118
Capacity as specified by the
applicant, (cc)
: 2780
2.1.4 Fuel System:
Type of fuel feed system : Gravity and forced feed
2.1.4.1 Fuel feed pump:
Make : Bosch, India
Type : Plunger with hand primer
Model/Group combination No. : FP/KSG22AD105, F002 A50 040
2.1.4.2 Fuel Injection pump:
Make : Bosch, India
Model/Group combination No. : F002 A0Z 635, PES3A90D320RS3500
Type : Inline, Plunger
Serial number : 03743452
2.1.4.3 Fuel injectors:
Make : Bosch, India
Model/Group combination No.:
Holder number : F002 C70 552
Nozzle no. : DSLA 148P 1549
Type : Multi hole (five holes)
Injection timing : 12° ± 2 degree before TDC
2.1.4.4 Governor:
Make : Bosch, India
Model/Group combination No. : RSV325…1000A5C1531R
Type : Mechanical, centrifugal, variable speed
2.1.5 Air Intake system:
2.1.5.1 Pre-cleaner
Make : Sonalika
Type : Centrifugal with transparent dust collector
Location : Above main air cleaner inlet tube, outside the
bonnet
2.1.5.2 Air cleaner:
Make : Pratibha Engg. & Fab.
Type : Oil bath
Location : In front of radiator, under the bonnet
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 7 of 14
2.1.6 Exhaust System:
Type of silencer : Up-draught, (Elliptical )
2.1.7 Lubricating system:
Type : Force feed and splash
Cooling device, (if any) : None
2.1.8 Cooling system:
Type : Forced circulation of coolant and water
Coolant as recommended : Veedol, ELF
Coolant water ratio : 30:70
2.1.9 Starting System:
Type : 12V, DC, Electrical
2.1.10 Transmission System
2.1.10.1 Clutch:
Make : AMREP
Type : Single, dry friction plate
No. of friction plate, : One
Size, OD/ID, (mm) : 279.5/ 165.4 ᶲ
2.1.10.2 Gear box:
Make : Sonalika
Type : Mechanical, constant mesh gears
No. of speeds:
- Forward : 08
- Reverse : 02
2.1.11 Power lift (hydraulic system):
Make : Sonalika
Type : Open centre, Live, ADDC
No. and type of cylinder : One, single acting
2.1.12 Drawbar:
2.1.12.1 Linkage Drawbar [Refer Fig.1] :
Notation As per IS: 12953-1995
(Reaffirmed in October,
2017), (Cat. I/Cat.II) (mm)
As measured, (mm) Remarks in the case of
Present Sample
Previous
Sample
Present
Sample
A 683 1.5 / 4001.5 682.0 683.0 Conforms to Cat. I
B 75 (min) / 75 (min) 74.0 79.40 Conforms to Cat. I & II
C 30 (min) / 30 (min) 30.0 31.30 Conforms to Cat. I & II
D 21.79 to 22.0 / 27.79 to 28.0 27.80 27.90 Conforms to Cat. II
E 39.0 (min) / 39.0 (min) 64.50 65.53 Conforms to Cat. II
F 12.0 (min) / 12.0 (min) 12.00 12.00 Conforms to Cat. I & II
G 15.0 (min) / 15.0 (min) 21.00 22.57 Conforms to Cat. I & II
H 25 1 / 25 1 25.00 24.95 Conforms to Cat. I & II
J 80 1.5 / 80 1.5 80.7 79.92 Conforms to Cat. I & II
No. of holes 7 / 9 07 07 Conforms to Cat. I
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 8 of 14
Fig.1: DIMENSIONAL NOTATIONS FOR LINKAGE DRAWBAR
2.1.13 Towing hitch:
Front:
Type : Clevis
Location : At front, on front axle mounting bracket
Height above ground level, (mm) : 685
Type of adjustment : None (fixed)
Width of clevis, (mm) : 108.50
Dia of pin hole, (mm) : 28.7
2.1.14 Wheel Equipment:-
2.1.14.1 Steering Wheel (s):
Make : CEAT
Number(s) : 02
Type of tyre : Pneumatic, ribbed
Size & ply rating : 6.00-16 & 08 PR
Make & size of rims : AMW & 4.50 E × 16
2.1.14.2 Drive wheel (s):
Make : CEAT
Number : 02
Type of tyre : Pneumatic, traction
Size & Ply rating : 13.6-28 & 12 PR
Make & size of wheel rim : SSWL & W12 X 28
2.1.15 Labelling of tractor as per IS: 10273-1987 (Reaffirmed in March, 2014):
Locations of labelling plate:- It is riveted on outside of LHS fender and provides the
following information:
Name of Manufacturer : M/S. International Tractors Limited
Hoshiarpur, (Punjab) India
Make : International Tractors Limited
Model : Sonalika International DI-740 III CM Series
Month & Year of manufacture : 02 / 20
Engine Serial Number : 3100ELI04B908045F3
Chassis Serial Number : MZESH912583S3
Maximum PTO Power, kW : 29.5
Specific Fuel Consumption, g/kWh : 265
ØF
ØD
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 9 of 14
3. SUMMARY OF OBSERVATIONS, COMMENTS & RECOMMENDATIONS
3.1 The performance results have been reproduced from Commercial 1st Batch Test report
No. T- 1230/1757/2019 (March, 2019) / On the basis of test conducted the performance results have been summarized as evaluative (mandatory) and non – evaluative (not mandatory) parameters applicable for qualifying Minimum Performance Criteria as per clause-4 Table-1 of Indian Standard 12207: 2019 for acceptance of tractor for the purpose of subsidies/NABARD financing are summarized as under.
Sl. No.
Characteristic
Category
(Evaluative / Non
Evaluative)
Requirements as per IS: 12207-2019
Values declared
by the applicant
(D)/ Requirement
(R)
As observed
Whether meets
the require -ments
(Yes/No)
1 2 3 4 5 6 7
3.1.1 PTO Performance: a) Maximum power
under 2 h test, (kW ) (Natural ambient condition)
Evaluative Declared value to be achieved with a tolerance
of: 5 % for PTO power and or Engine power >26
kW. 10% for PTO power
and or engine 26 kW
29.5 (D) 28.0 Yes
b) Power at rated engine speed, (kW)
Non Evaluative
-do- 29.5 (D) 27.7
Yes
c) Specific fuel consumption corresponding to maximum power, (g/kWh)
Evaluative + 10%
265 (D) 254 Yes
d) Maximum equivalent crankshaft torque, (Nm)
Non Evaluative
8%
165 (D) 172.9 Yes
e) Back-up torque, percent
Evaluative 12 percent, min. 12% (D) 30.8 Yes
12% (R) f) Maximum operating temperature, (
OC)
1) Engine oil Evaluative The declared value should not exceed the max. value specified by the oil company and the observed value under high ambient condition should not exceed the declaration.
132 (D) 87 Yes
2) Coolant Evaluative The declared value should not exceed the boiling temperature of coolant under the pressurized or otherwise and the observed value under high ambient condition should not exceed the declaration.
110 (D) 105 Yes
g) Engine oil consumption, (g/kWh)
Evaluative
Not exceeding 1% of SFC at max. power under High ambient conditions
2.54 Maximum
(R) 1.16 Yes
h) Smoke level, m-1
Evaluative Maximum light absorption coefficient of 3.25 per meter or equivalent BOSCH No. 5.2 or 75 Hatridge value.
3.25 maximum
(R) 0.09 Yes
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 10 of 14
1 2 3 4 5 6 7
3.1.2 Drawbar performance :
a) Max. drawbar pull with ballast corresponding to 15 percent wheel slip or 7 percent track slip, (kN)
Non Evaluative
Minimum 70% of static mass with ballast
18.06 (D) 21.32 Yes 18.06 (R)
b) Max. drawbar pull without ballast corresponding to 15 percent wheel slip or 7 percent track slip, (kN)
Evaluative Minimum 70% of static mass of tractor without ballast or with standard ballast, as the case may be
13.39(D) 16.40
Yes 13.39(R)
Minimum
c) Maximum drawbar power without ballast as in case may be, (kW)
Evaluative Minimum 80 % of PTO power as referred in Sl No. i) a) of PTO performance in case of tractors having total static mass > 1500 kg Minimum 75 % of PTO power as referred in Sl No. i) a) of PTO performance in case of light weight tractors having 1500 kg total static mass of tractor Minimum 75 % of the engine power as referred in Sl No. i) a) of engine performance in case of tractors which do not have a PTO shaft.
22.4 (D)
26.1
Yes 22.0 (R) Minimum
d) Maximum transmission oil temperature (
oC)
Evaluative To be declared by the manufacturer. 130 (D) 75 Yes
3.1.3 Power lift and hydraulic pump performance : a) Maximum lifting capacity throughout the range of lift, (kN):
1) At hitch points
Evaluative Tolerance of ± 10% 15.6 (D) 15.56 Yes
2) With the standard frame
Evaluative The lift capacity should at least be 24 kg/PTO kW. and it should be 21.5 kg/engine kW where the tractor is not provided with a PTO shaft
7.00 (D) 14.43 Yes 7.67 (R)
b) Maximum drop in the height of the point of application of the force after each 5 minutes interval for a total duration of 30 Minutes, (mm)
Non Evaluative
The observed value should not exceed 50 mm
50 (D) 13 Yes 50(R)
Maximum
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 11 of 14
1 2 3 4 5 6 7
3.1.4 Brake performance at 25 kmph:
a) Maximum stopping distance at a force, equal to or less than 600 N on brake pedal with road ballast, (m): 1) Cold brake Evaluative 10 m 10 (R) 8.51 Yes
2) Hot brake Evaluative 10 m 10 (R) 8.77 Yes
b) Maximum force exerted on the brake pedal to achieve a deceleration of 2.5 m/s
2 (N)
Evaluative 600 N 600 (R)
Maximum
476 to
499 Yes
c) Whether parking brake is effective at a force of 600 N at foot pedal (s) or 400 N at hand lever, N
Evaluative Yes / No Yes Yes Yes
3.1.5 Noise measurement : a) Maximum ambient
noise emitted by the tractor dB(A)
Evaluative 88 dB (A) for >1.5 tonne GVW and 85 db (A) for <1.5 tonne GVW (as per CMVR)
81 Yes
b) Maximum noise at operator’s ear level dB(A)
Evaluative 96 (as per CMVR) 95 Yes
3.1.6 Amplitude of mechanical vibrations at: 1) Left foot rest
Non Evaluative 100 microns (max)
170 No
2) Right foot rest 190 No
3) Seat (with driver seated)
70 Yes
4) Steering wheel 120 No
3.1.7 Air cleaner oil pull over test :
Maximum air cleaner pull over, (%)
Evaluative 0.25% (Max) 0.11 Yes
3.1.8 Haulage requirements : a) Gross mass of the trailers, (tones):
1) Two wheel Non Evaluative To be specified by manufacturer
4.0 (D) 4.0 Yes
2) Four wheel Non Evaluative 5.0 (D) 5.0 Yes b) Distance travelled / liter of fuel consumption, (km/l):
1) Two wheel Non Evaluative --do-- 5 to 6 (D) 6.22 to 6.29
Yes
2) Four wheel Non Evaluative --do-- 5 to 6 (D) 6.46 to 6.48
Yes
c) Fuel consumption (ml/km/tonne): 1) Two wheel Non Evaluative --do-- 30 to 40 (D) 39.8 to
40.2
No
2) Four wheel Non Evaluative --do-- 30 to 40 (D) 30.9 to 31.0
Yes
3.1.9 Wetland cultivation (Puddling Operation): Sealing for the following assemblies:
Evaluative The identified assemblies should essentially meet the requirement of IS: 11082. No water ingress in the identified assembly given in column-2. If tractor does not meet the requirements of wetland cultivation, it may be recommended for dry land operation only.
There should be no ingress of water and / or
mud (R)
No ingress of water and / or
mud was observed during ICT test vide
test report no. T-871/ 1385/2013
(April, 2013)
Yes
1) Clutch assembly
-do-
2) Brake housings -do-
3) Front axle hubs -do-
4) Engine oil -do-
5) Transmission oil
-do-
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 12 of 14
1 2 3 4 5 6 7
3.1.10 Safety features :
a) Guards against moving and hot parts
Evaluative
Belt drives, pullies, silencer, hydraulic pipes (As per IS: 12239 (Part-2)
Meets the requirement
Yes
b) Lighting arrangement Evaluative
As per CMVR Meets the requirement
Yes
c) Seating requirements (Tractors having more than 1150 mm rear track width)
Non Evaluativ
e
Should meet the requirements of IS: 12343 (As amended from time to time)
Does not meets the
requirement
No
d) Technical requirements for PTO shaft
Evaluative
Should meet the requirements of IS: 4931 (As amended from time to time)
Meets the requirement
Yes
e) Dimensions of three point linkage
Non Evaluativ
e
Should meet the requirements of IS: 4468 (Part-I) (As amended from time to time)
Does not meets the
requirement
No
f) Specifications of linkage drawbar
Evaluative
Should meet the requirements of IS 12953 (As amended from time to time)
Meets the requirement
Yes
(g) Swinging drawbar (wherever fitted)
Evaluative
Should meet the requirements of IS 12362 (Part 3) (As amended from time to time)
Not provided Not appli-cable
(h) 1) Maximum traveling speed at rated engine speed in reverse gear, kmph
Evaluative
Should not exceed 20 kmph
9.94 kmph (Meets the
requirement)
Yes
2) Audible warning signal on tractor
Evaluative
As soon as the travelling speed in reverse gear reaches to 20 kmph ,an audible warring signal on tractor be activated , The safety aspects about the operation of shuttle technology shall be brought in operation and manufacturer /dealer shall ensure the training on this aspect to operator before the delivery of tractor.
Not provided Not appli-cable
3.1.11
Labelling of tractors (Provision of labelling plate):
1) Make Evaluative
Should conform to the requirements of CMVR along-with maximum PTO power in kW and year of manufacture in numerical form
MM YY
Digit 01-12 in box No.1 for MM will represent the months & next two digits in box No.2 for YY will represent the year of manufacturing.
International Tractors Limited
Yes
2) Model Evaluative
Sonalika international DI-740 III CM Series
Yes
3) Month & Year of manufacture
Evaluative
02 / 20 Yes
4) Engine number
Evaluative
3100ELI04B908045F3
Yes
5) Chassis number
Evaluative
MZESH912583S3
Yes
6) Declaration of PTO power, (kW)
Evaluative
29.5 Yes
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 13 of 14
1 2 3 4 5 6 7
3.1.12 Discard limit for, (mm) : (a) Cylinder bore diameter,
(mm) Evaluative
To be specified by the manufacturer and supported by the printed literature
100.30 100.061 to 100.070
Yes
(b) Clearance between piston & cylinder liner at skirt, (mm)
Non Evaluative 0.450
0.153 to 0.173
Yes
(c) Piston diameter at skirt, (mm)
Non Evaluative
-do- 99.20
99.897 to 99.917
Yes
(d) Ring end gap (mm):
- Top comp. ring Evaluative --do-- 2.00 0.40 to 0.45
Yes
- 2nd
comp. ring Evaluative 2.00 0.80 to 0.85
Yes
- Oil ring. Evaluative 2.00 0.60 Yes
(e) Ring groove clearance (mm): - Top comp. ring
Evaluative -do-
--Tapered--- Not
Appli-cable
- 2nd
comp. ring Evaluative
-do- 0.16
0.056 to 0.060
Yes
- Oil ring. Evaluative
-do- 0.20
0.040 to 0.055
Yes
(f) Clearance of main bearings (mm):
- Diametrical clearance
Evaluative
-do-
0.20 0.060 to 0.131
Yes
- Crankshaft end float
Evaluative 0.60 0.45 Yes
(g) Clearance of big or small end bearings, (mm):
- Diametrical Evaluative
-do- 0.30 0.118 to 0.130
Yes
- Axial Evaluative
-do- 0.75 0.25 to 0.30
Yes
(h) Clearance between king pin and bush, (mm)
Non Evaluative
-do- 1.00 0.02 to 0.22 Yes
(i) Clearance between centre pin and bush, (mm)
Non Evaluative
-do- 1.00 0.18 to 0.27
Yes
3.1.13 Literature (Submission to test agency)
(a) Operator manual Evaluative The printed literature in
booklet form should be
provided as per IS 8132
& should submit along
with the test sample
Provided Provided
Yes
(b) Parts Catalogue Evaluative Provided Provide
d Yes
(c) Workshop / Service manual
Evaluative Provided Provided
Yes
3.1.14 Fitment of Roll Over Protective Structures (ROPS): for tractor having more than 1150 mm rear track width
Evaluative ROPS should meet the
requirement of IS 11821
or OECD code or
equivalent International
standard
ROPS not fitted Not appli
-cabl
e
3.1.15 Standard Accessories Evaluative Trailer hitch, front tow
hook, linkage drawbar
should be provided with
the tractor.
Provided Yes
3.1.16 Accessories (optional)
Non Evaluative
Ballast weights, if
fitted, should meet
the requirement of
CMVR
Provided Yes
T- 1378/1905/2020
INTERNATIONAL TRACTORS LIMITED,
SONALIKA INTERNATIONAL DI-740 III CM SERIES TRACTOR
- Commercial (Administrative Extension)
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE – BUDNI Page 14 of 14
3.2 CATEGORY OF BREAKDOWNS / DEFECTS (As per Clause 5.0 of IS:12207-2019) :
S. No. Category of breakdowns
Category (Evaluative /
Non Evaluative)
Requirements as per
IS: 12207-2019 As observed
Whether meets the
Requirements (Yes/No.)
1. Critical Evaluative No critical breakdown None Yes
2. Major Evaluative Not more than one and neither of them should be repetitive in nature
None Yes
3. Minor Evaluative Not more than three and frequency of each should not be more than two.
None Yes
4. Total breakdowns
Evaluative In no case, the total number of breakdowns should exceed four, that is, (1 major + 3 minor) or 4 minor breakdowns.
None Yes
3.3 Salient Observations:
This tractor model meets the evaluative requirements of IS: 12207-2019.
4. CITIZEN CHARTER
Time frame for Testing & Evaluation as per Citizen
Charter
Duration of Test Whether the Test Report is released within the time frame given in Citizen Charter
Remarks
10 Months 01 Month
(February, 2020) Yes --None--
TESTING AUTHORITY:
RAJNEESH PATEL
AGRICULTURAL ENGINEER
C.V. CHIMOTE
TEST ENGINEER
J.J.R. NARWARE
DIRECTOR The report compiled by Smt. Poonam Khurasia, Senior Technical Assistant
5. APPLICANT’S COMMENTS
--Nil--