Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
RANGE
(ELECTRICAL)
INSTRUCTION AND
MAINTENANCE MANUAL
“Professionally with Professionals”
DESCRIPTION
Our dear customer,
Your preferred KUSİNA is nature and technology friendly. We thank you for your choice.
KUSİNA has been produced with the understanding of "Total Quality" in modern production facilities.
Important Safety Information
Carefully read this guide and keep it for future review.
WARNING: Installation of the devices must be done by an authorized service person.
WARNING: Equipment must be grounded.
Indicates that there is a risk of personal injury or property damage.
Explosion / fire hazard.
The instructions in this manual contain important information on the safe mounting, usage,
cleaning and maintenance of the device. Thus, keep the manual at a place easily accessible by
the person who will use the machine, and the technician.
Mounting, electrical connection and maintenance works of the device should be performed by a
specialist authorized in this subject and in accordance with the instructions of the manufacturer
company.
Electrical connection of the device should be arranged according to the tables and electrical
diagram given in this manual.
Manufacturer Company accepts no responsibility for the final damages incurred in humans or
properties that are caused by any procedure not conforming to the instruction manual, or
maintenance or technical interventions that are not performed by authorized people.
Product Types • G6K100E – 600 serie ½ module counter top
• G6K200E – 600 serie 1 module counter top
• G7K100E – 700 serie ½ module cupboard
• G7K200E – 700 serie 1 module cupboard
• G7K210E – 700 serie 1 module oven
• G9K100E – 900 serie ½ module cupboard
• G9K200E – 900 serie 1 module cupboard
• G9K210E – 900 serie 1 module oven
Please check the table (1) below for the product specifications
MOUNTING
Placement Installation and adjustment of the device should be carried out by technical staff of the
Authorized Service.
Place the device at a place min. 10cm away from the side or back wall to prevent excessive
temperature rises.
Place the device beneath a filtered exhaust hood in order to eliminate smell and fume that may
be emitted during cooking.
Device should be placed on a flat surface by suitably balancing on the four adjustable legs.
(Figure A)
Remove the protective nylon on the device. Clean the adhesive particles left on the device with a
suitable cleaner.
Never leave flammable material near the device.
Electrical Connection Connect the device to the electrical installation according to the electrical standards of the
relevant country.
Feed the device with suitable network voltage written on the information plate.
Connect to the electrical installation over a suitable automatic fuse. Fix the said fuse on a place
that is easily accessible in case of a danger.
The cable connecting the device to the electrical installation should be at least type H05 RNF.
Before connecting the electrical inlet cable to the inlet clamp on the device, connect the cable by
passing it through the inlet coupling. And then tighten the coupling cover in a manner that does
not allow cable return.
Electrical inlet is indicated with a label on the device.
If the device will be used in a commercial kitchen, apply a correct grounding system. Here,
consider DIN VDE D100 Article 540.
Grounding screw ” ” is indicated with a label behind the device.
OPERATOR INSTRUCTIONS With the aim of eliminating the protection oil on it, operate the device and ovens at maximum
level for a while. Then, cover with vegetable oil again.
Clean the accumulated food residues that are burned and carbonized on the cooking surface and
oven with a suitable tool everyday at the end of operation. If the said daily maintenance is not
performed, accumulated burned food residues may cause a decline in cooking efficiency by
creating a crust on the plates
Do not operate the oven with its back funnel mouldings removed or closed.
BEFORE USE
Electrical system check After mounting, check the controlling members and heaters by operating at different temperatures.
After the installation and maintenance, check the heating power of device.
During first operation, device will emit fume and smell for a short period. This fume and smell is the
result of the insulation material and the substances such as oil, etc. on the metal sheet surfaces. This is not
dangerous and will disappear by itself.
During the first use of the device should be run in the highest degree of operating for a period of 1 hour
STARTING-UP COOKERS (Figure B) Each plate has 6 adjustable Temperature value. Desired Temperature level is set with relevant
button (1).
1 is the lowest Temperature and 6 is the highest Temperature.
STARTING-UP OVEN (Figure B) Adjust the thermostat to desired temperature (2).
Adjust cooking area (4), you will see that the indicator light is on.
When the indicator (3) light is off, it means that the oven has reached the desired temperature.
Positions of change over switch is below:
TURN OFF
(Up 1500W down 4500W)
Upper Heater (Up 4500W)
Lower Heater (Down 4500W)
TURN OFF Turn the switch to position “0”.
Turn the thermostat to position “0”.
MAINTENANCE
Do not perform maintenance when the device is loaded with electrical power.
Before it cools down completely, wipe the device with a cloth immersed in warm soapy water.
Do not use cleaning substances and tools that may cause scratches on device surface.
Do not clean the device with water or vapour pressure. Otherwise, you may cause electrical plate
failure.
If the device will not be used for a long period, coat the surfaces with a thin layer of Vaseline. In
case of any dangerous condition with the device, notify to the authorized service. Never let
unauthorized people to interfere in the device.
Figure A
Compatibility Information
This device is designed and manufactured in accordance with the following directives and standards.
marking directive, 93/68/EEC
TS EN 60335-1:2012/AC
TS EN 60335-2:37
Related to CE Directive(s):
2014/35/EU (Low Voltage)
1 2 43
Şekil BFigure B
1
Figure B
Limitation of Liability: All technical information contained in this manual, operating instructions,
operation and maintenance of the device, contains the latest information on your device. The
manufacturer accepts no responsibility for damage or injury which may result from failure to follow the
instructions in this manual, use outside of the intended use, unauthorized repair, unauthorized
modifications to the device, or use of spare parts not approved by the manufacturer.
Table (1)
G6K100E G6K200E G7K100E G7K200E
G7K210E G9K100E G9K200E G9K210E
Width (A) mm 400 600 400 800 800 400 800 800
Dept (B) mm 600 600 730 730 730 900 900 900
Hight (C) mm 300 300 900 900 900 900 900 900
Power Kw 3 Kw 8 Kw 3,5 Kw 7 Kw 13 Kw 6 Kw 12 Kw 18 Kw
Electrical Inlet
400 V
3N PE
400 V
3N PE
400 V
3N PE
400 V
3N PE
400 V
3N PE
400 V
3N PE
400 V
3N PE
400 V
3N PE
Cable Sections mm² 5x2,5 5x2,5 5x2,5 5x4 5x4 5x2,5 5x4 5x4
G6K100E G6K200E
600
300
ELEKTRİK GİRİŞ
ELECTRICAL INLET
ELEKTRİK GİRİŞ
ELECTRICAL INLET
400
G6K100E
600600
300
ELEKTRİK GİRİŞ
ELECTRICAL INLET
ELEKTRİK GİRİŞ
ELECTRICAL INLET
G6K200E
G7K100E G7K200E
G7K210E G9K100E
G9K200E G9K210E
730
900
400
ELEKTRİK GİRİŞ
ELECTRICAL INLET
G7K100E
730
900
800
ELEKTRİK GİRİŞ
ELECTRICAL INLET
G7K200E
730
900
800
Elektrik GİRİŞ
Electrical INLET
G7K210E
900
900
400
ELEKTRİK GİRİŞ
ELEKTRICAL INLET
G9K100E
900
900
800
ELEKTRİK GİRİŞ
ELECTRICAL INLET
G9K200E
900
900
800
ELEKTRİK GİRİŞ
ELECTRICAL INLET
G9K210E
PE
M
L3
4 3 1 2 5
P2 P1 P3
4 3 1 2 5
A1
L2
L1
N
400V AC 3N PEG9K100E
P2 P1 P3
A1,2 - PLEYT ŞALTERİ/ PLATE SWİTCHES
R1,2 -PLEYT/ PLATES
5X2.5mm² H07 RNF
R2R1
4 1 3 2
PE
4
3
2
1
A 1 ,2 , 3 ,4
P1 P2 P3
0
1
3
2
5
4
6
1 2 3 4 3 1 5
A2
M - GIRIŞ KLEMENSI/ INLET CLAMP
4 1 3 2
PEM L3
43
12
5
P2
P1
P3
43
12
5
A1
L2
L1
N
43
12
54
31
25
400
V A
C 3
N P
EG
9K
200E
P2
P1
P3
P2
P1
P3
P2
P1
A1
,2,3
,4 - P
LE
YT
ŞA
LT
ER
İ/ PLA
TE
SW
İTC
HE
S
R1
,2,3
,4 -P
LE
YT
/ PLA
TE
S
5X
2.5
mm
² H07 R
NF
R4
R3
R2
R1
41
32
PE 4 3 2 1
A 1
,2 , 3
,4
P1
P2
P3
013 25 46
12
34
31
5
A2
A3
A4
M - G
IRIŞ
KL
EM
EN
SI/ IN
LE
T C
LA
MP
41
32
41
32
23
14
PEM L3
43
12
5
P2
P1
P3
43
12
5
A1
L2
L1
N
43
12
54
31
25
11
21
31
12
22
33
H1
F1
40
0V
AC
3N
PE
G9K
21
0E
P2
P1
P3
P2
P1
P3
P2
P1
R6
- FIR
IN A
LT
ISIT
CIL
AR
/ OV
EN
BO
TT
OM
HE
AT
ER
S
R5
-FIR
IN Ü
ST
ISIT
CIL
AR
/OV
EN
TO
P H
EA
TE
RS
A1
,2,3
,4 - P
LE
YT
ŞA
LT
ER
İ/ PL
AT
E S
WİT
CH
ES
A5
- FIR
IN Ş
AL
TE
Rİ/O
VE
N S
WİT
CH
H1
,2 -L
AM
BA
/ LIG
HT
IND
ICA
TO
R
F1
- TH
ER
MO
ST
AT
R1
,2,3
,4 -P
LE
YT
/ PL
AT
ES
5X
4m
m² H
07
RN
F
21
43
1a
2a
3a
4a
5a
6a
21
34
65
p1
p3
p2
p4
8a
7a
87
H2
R6
A5
12
p1
p2
3
1a
43
p4
p3
2a
3a
21
4a
5a
45
7a
6a
8
67
8
A5
R4
R3
R2
R1
41
32
1234M PE
PE
L3
N L1
L2
PE 4 3 2 1
A 1
,2 , 3
,4
P1
P2
P3
013 25 46
12
34
31
5
A1
A1
A1
H2
M - G
IRIŞ
KL
EM
EN
SI/ IN
LE
T C
LA
MP
41
32
41
32
23
14
11 21 31
12 22 33
H1
F1
400V AC 3N PE
G9K210E-FIRIN
R6 - FIRIN ALT ISITCILAR / OVEN BOTTOM HEATERS
R5 -FIRIN ÜST ISITCILAR /OVEN TOP HEATERS
A1,2,3,4 - PLEYT ŞALTERİ/ PLATE SWİTCHES
A5 - FIRIN ŞALTERİ/OVEN SWİTCH
H1,2 -LAMBA/ LIGHT INDICATOR
F1 - THERMOSTAT
R1,2,3,4 -PLEYT/ PLATES
5X4mm² H07 RNF
21 43
1a 2a 3a 4a 5a 6a
21 3 4 65
p1 p3p2 p4 8a7a
87
H2
R6
A51 2
p1 p2 3
1a43
p4p3
2a 3a
21
4a 5a
4 5
7a6a 8
6 7 8
A5
1
2
3
4
M
PEPE
L3
N
L1
L2
H2
M - GIRIŞ KLEMENSI/ INLET CLAMP
EVALUATION: APPROVERS
SOLUTION PROPOSAL:
DATE:
PROBLEM DESCRIPTION:
SIGN:
PRODUCT NAME: DETECTED ( Name , Appellation)
CUSTOMER
NAMECUSTOMER COMPLAINT
DETECTION TYPE
CORRECTIVE \PREVENTIVE ACTIVE FORM
OPTIMIZATION REQUEST/
DESCRIPTION
Note: If required, you can send it to our company by viewing the
form above or by post.
+90 232 853 92 00
www.kusina.com.tr
As a KUSİNA, we realize the production of our devices with CE certificate.
We continue to contribute to the environment using recycled paper.
Manufacturer: Gürçelik Dayanıklı Tüketim Mamülleri Mut. Ins. Tur. Tar.San.Tic. Ltd.Sti.
Adress: Bahçelievler Mahallesi Sakarya Cad. No:11 Yazıbaşı/Torbalı- İZMİR
Phone: +90 232 853 92 00
Web: www.kusina.com.tr – www.gurcelikas.com
E-mail: [email protected]
is a brand.