N°4N°5

2 persons

N°13N°17

!

1

Variable number

Ce

Sp

Cl

RtEb

Po1Po2 Eq

Bc

Installer and user’s manualVARANDA AWNING

INFORMATION PRE-INSTALLATION

Before the installation, check the leveling of the place where you will apply the awning. Dimensions should be parallels and levelled. In case the balcony is not level it's necessary an chock application to allow correctly the installation of the awning �xing plates.

Necessary tools

Inside package

Important

porch

2

B

A assembly

20cm max

100cm max

Sp

Cl

bottom

Make the same assembly to the other pro�le. Cl

3

Eq

Bc

assembly

Po1

top

A Disassemble B Assembly

C Slide the frontal pro�le on the fabric.

D Assembly again

N°4

100cm max

Fixing plates preparation

Awning and frontal pro�le preparation.

30cm mini

Cl

C

4

D E

F G

A B

30cm min

Cl

C D E

F

A B

Ø6x14mm

Ø6x14mm

support tubes

Adapt the awning �xation to the balcony type.

Balcony without tubes supports

Balcony with support tubes.

Attention, is necessary to respect the position described above represented for a awning set assembly. Adapt the awning �xation to the balcony type.

Fixation plates application.

attention, is necessary to respect the position described above represented for a awning set assembly.

5

Simple guide

Double guide

Balcony without supporting tubes.

Simple guide

Double guide

Others supports

Balcony with support tubes.

6

A

B C

Installation of safe

Placing the maneuver rope.6disassembleassemblyA

50cm

D

B face

front pro�le

winding direction

to C

B Face

to D

from B

-

CCover

!

D Front pro�le

B

Dto

from

OK

NO

P1

50cm

Eb

Cfrom

2

3to

RtPo2

1

to

from

3Po1

4

to

Ac

Ac

4from

to

for closure

5Po1

Eb

Po2

4

25

from 3

Ccover

Attention, for correct operation of the awning, pay close attention to the following statements. Operation to be carried out on the 2 reinforcements.

All respecting the winding direction, perform 3 courses of wire around the roller tube and pulley set. Pass the thread underneath the pulley P1 sliding it by the guide and �nding the bottom cover in C.

Po1 pulley must be placed in the middle of the front pro�le.

Preassembly 2 parts.

Attention from B to C ensure that the rope does not wind on her own, it can cause a break after much use.Then slide the rope by the pro�le, pass the rope through the pulley and make it slide again by the pro�le until the load bar.Attention: the placement of the cover will be made at the time of string stretched.

7

Assembly end

8

ClosureAwning open 30cm Opening

N°4N°4

7

Pull the end of the rope by hand and lock on release AC. The stretch should identify two sides to check that the pulley Po1 is well positioned in the center of the front pro�le. Ensure that the rope is guided on all the pulleys of the system. Open the awning down. Open the fabric 50cm, to perform another string tension. Make an opening maneuver and closing. The awning becomes tense.

The travel stops are pre-adjusted in factory. To adjust:- Unscrew the limit screw + or - to make the desired setting. Rotating + to get more closing or opening turning - to get less closing or opening.-Make a test.

After adjustments are made, put the safe cover again (paragraph 6) and the front cover pro�le (paragraph 3).

Fabric stretch

Regulation of the limit switches

Finishing

Information to the consumer

Awning maintenance advice

Problems Causes

Not install the awning in case of:

Wind Rain Snow Nothing suspended

Solutions

An awning is subject to some adverse situations: moisture, salt spray, balance, wind ...we recommend that:

- Check the tightening of the screws and the limit after installation and regularly at the beginning and end of each season.

-Never close a wet awning. Dry it if possible.

-Clean the fabric and the frame at the beginning and end of each season. Caution: never use detergents.

The awning balcony disintegrated from the structure.

The Mounting brackets are not adapted to the composition of the structure.

Check proper placement of the supports (according to the manual's instructions).In case of �xing with a chemical seal, report to the manufacturer.Check the entire circuit of the rope to �nd a possible shift of the rope. (Paragraph 6)Check if the voltage is identical in the 2 sides (sheave Po1 centered) (Paragraph 6)

Tighten the rope (Paragraph 7)

Do the full circuit of the rope again. paragraph 6Test the electrical part to �nd the problem.

Check the motor connectionCheck engine operation by connecting directly to the power input. (black or brown blue blue)

Wait the end of protection (20 minutes)

Incorrect voltage on the base.Fabric not stretched. (Natural e�ect)Rope break.Electrical maneuver faulty The engine is placed in thermal protection after 2 descents and a 1 rise successives.

Connection problem.

A Rope broke free of a pulley.The Tension of one rope is superior to another (double Po1 o�set)

The front pro�le does not work normally.

The fabric is not stretched.

The awning does not open or close.Electric awning maneuvers do not work.

Electric awning maneuvers do not work.

1 JSV03A

2 FUM42

3 TM40

4 CV03/CV02

5 PO16P

6 TO78

7 CV01

8 EO678P

9 CU14A

10 SV06A

11 PU807

12 SV05

13 EB0802

14 PU3704

15 TR19

16 PO20

17 PU3703

18 PO2102

N.R* AC02

N.R* C03

4

21

56 8

9

12

1516

1011

13

1718

7

*no represented part

14

3

SV35 SV3402 SV15A SV04 = 9mmSV14 = 13mmSV24 = 20mm

Exploded view

Aluminum parts

Engine bracket

Tubular motor

Safe cover

Pulley winding tube

Roller tube Ø78mm

Safe pro�le

Bushing Ø78mm

Roller tube support

Safe guide

Sliding pro�le

Front cover pro�le

Guide cover

Front pro�le’s cover

The fabric tension spring

Pulley to spring TR19

Front Pro�le

Tension pulley

Fixing the rope to the terminal pro�le

Rope

Number Reference Designation