INSTALLATION VERSION 1 2015 CR-V INSTRUCTIONS ......2015 CR-V SEP 2014 PARTS LIST Remote Control Engine Starter Unit Kit P/N 08E91-T2A-100C Transmitter Control unit Antenna ID label

Publications No.

INSTALLATIONINSTRUCTIONS

Accessory Application

© 2014 American Honda Motor Co., Inc. – All Rights Re

VERSION 1
REMOTE CONTROLENGINE STARTER
served. AII 52560 (1409

2015 CR-V

) 0

Issue Date

SEP 2014

PARTS LIST

Remote Control Engine Starter Unit KitP/N 08E91-T2A-100C

Transmitter

Control unit

Antenna

ID label

Remote Control Engine Starter Attachment KitP/N 08E92-T0A-100C

Control unit bracket

Engine starter harness

3 Relays

20 Wire ties

2 Long wire ties

5 Urethane tapes

Clip

Caution label

Fuse label

Accessory User’s Information Manual

1 of 288E92-T0A-1C00-90

Quick Start Guide

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Diagonal cutters

Ratchet

13 mm Sockets

10 mm Open end wrench

Torque wrench

Isopropyl alcohol

Scissors

Shop towel

Ruler

HDS/MVCI

Tape

Masking tape

The following tools are available through the Honda Tooland Equipment Program. On the iN, click on: Service >Service Bay > Tool and Equipment Program, then enterthe number under “Search”. Or, call 888-424-6857.

• Trim Tool Set (T/N SOJATP2014)

• Plastic Trim Tool (T/N SILTRIMTL10)

Illustration of the Remote Control Engine StarterInstalled on the Vehicle

QD22403BY

20A FUSES

CONTROL UNIT ANTENNA

3 RELAYS

3A FUSESENGINESTARTERHARNESS

2 of 28 AII 52560

INSTALLATION

Customer Information: The information in thisinstallation instruction is intended for use only by skilledtechnicians who have the proper tools, equipment, andtraining to correctly and safely add equipment to yourvehicle. These procedures should not be attempted by“do-it-yourselfers.”

NOTE: This antenna should be installed only if theambient air temperature 15°C (60°F) or above.

1. Move the driver’s seat all the way back.

2. Disconnect the negative cable from the battery.

3. Attach the ID label.

• Using isopropyl alcohol on a shop towel, cleanthe area where the ID label will attach.

• Attach the ID label to the transmitter in the areaas shown.

With Driving Position Memory SystemNOTE: The remote is factory set for driver 1 remotecontrol. To program the driver 2 remote, follow the“Register New Transmitter” instructions on ISIS orServiceExpress.

QB20939DH

ID LABEL

TRANSMITTER

Clean withisopropylalcohol.

(1409) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.

Without Driving Position Memory System

QB32111CH

ID LABEL

TRANSMITTER


Removing the Vehicle Parts

4. Remove the roof console.

• Using a plastic trim tool, pry out and remove theleft and right lens.

• Open the sunglass holder and remove the fourscrews.

• Remove the roof console and unplug the vehicleconnectors.

Q0N2012AG

VEHICLECONNECTORS

ROOFCONSOLE

4 SCREWS

4 RETAININGTABS

LEFTLENS

SUNGLASSHOLDER(Open.)

4 RETAININGTABS

RIGHTLENS

© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 52560

5. Release the driver’s sunvisor from the sunvisorholder.

QC50902AB

Rotate.

SUNVISORHOLDER

SUNVISORHOLDER

DRIVER’SSUNVISOR

6. Rotate the sunvisor holder 45° counterclockwise toremove the sunvisor holder.

7. Pull away the driver’s door opening seal from thedriver’s A-pillar. Gently pull out the driver’s A-pillartrim to release the clips.

Q0N2014AG

VEHICLEPANEL

CLIP

2 CLIPS

DRIVER’SA-PILLARTRIM

DRIVER’SDOOROPENINGSEAL(Pull away.)

CLIP

DRIVER’SA-PILLAR

(1409) 3 of 28

8. To prevent the clips from falling into the vehicle body,roll up the shop towel, and insert it between thedriver’s A-pillar and the dashboard. Take care not todamage the driver’s A-pillar.

Q0N2015BG

SHOPTOWEL

DRIVER’SA-PILLAR

DASHBOARD

9. Remove the driver’s A-pillar trim. Carefully removethe shop towel and any clips that fell from the driver’sA-pillar trim.NOTE: The upper clip will stay in the body.

Q0N2016AG

UPPER CLIPDRIVER’SA-PILLAR TRIM(Remove.)

DRIVER’SA-PILLARTRIM

4 of 28 AII 52560

10. Remove the remaining upper clip from the driver’sA-pillar.

Q0N2017AG

Push 2 tabs.UPPER CLIP(Discard.)

DRIVER’SA-PILLAR

11. Temporarily reinstall the driver’s A-pillar trim, andcheck the overlap between the headliner and thedriver’s A-pillar trim according to the service manual.Remove the driver’s A-pillar trim. Install the new clip(supplied) to the driver’s A-pillar trim.

Q0N2018AG

DRIVER’SA-PILLAR TRIM(inside)

NEW CLIP


12. Remove the driver’s dashboard panel and unplug thevehicle connector.

Q0N2019BG

VEHICLECONNECTOR

6 CLIPS

DRIVER’SDASHBOARDPANEL

13. Remove the driver’s air outlet.

Q0N2020BG

DRIVER’SAIR OUTLET

2 CLIPS

RETAININGTAB

SELF-TAPPINGSCREW

CLIP


14. Remove the driver’s dashboard under cover.

Q0N2021BGPINDRIVER’S DASHBOARDUNDER COVER

KNOB(Turn.)

CLIP

15. Remove the driver’s dashboard lower cover andunplug the vehicle connectors.

QAN2325AD

VEHICLECONNECTORS

8 CLIPSDRIVER’S DASHBOARDLOWER COVER

(1409) 5 of 28

16. Attach the tape to the upper column cover as shown.

Q0N2023AG

TAPE

UPPER COLUMN COVER

STEERINGWHEEL

17. Lower the tilt lever, and turn the steering wheel 90°counterclockwise.

Q0N2024BG

PLASTIC TRIMTOOL

STEERINGWHEEL

LOCK

UPPER COLUMN COVER

90° Counterclockwise.

18. Using a plastic trim tool, release the lock as shown.

6 of 28 AII 52560

19. Turn the steering wheel 180° clockwise. Using aplastic trim tool, release the lock as shown.

Q0N2025BG

LOCK

UPPER COLUMN COVER

PLASTIC TRIM TOOL

180° Clockwise.

20. Secure the upper column cover to the meter panelwith the tape.

Q0N2026AG

TAPE

2 RETAININGTABS

UPPER COLUMNCOVER

METER PANEL


21. Remove the two self-tapping screws from the lowercolumn cover.

Q0N2027AGLOWER COLUMNCOVER

2 SELF-TAPPINGSCREWS

22. Remove the lower column cover.

Q0N2028AGSELF-TAPPINGSCREW

LOWERCOLUMNCOVER


23. Remove the driver’s front door sill trim.

Q0D2801AD

2 RETAINING TABS

3 CLIPS

2 HOOKS

DRIVER’SFRONT DOORSILL TRIM

24. Pull away the driver’s door opening seal, and removethe driver’s kick panel.

Q0N2030AG

DRIVER’S DOOROPENING SEAL(Pull away.)

DRIVER’S KICKPANEL

2 CLIPS

(1409) 7 of 28

Installing the Antenna

25. Using scissors, cut one urethane tape in half. Wraptwo halves of urethane tape to the antenna cable asshown.

QB62501BK

ANTENNA

60 mm(2.4 in.)

60 mm(2.4 in.)

HALVES OFURETHANE TAPE(Do not foldthe antenna cable.)

URETHANE TAPE(Cut in half.)

ANTENNACABLE

If the vehicle is equipped with the camera, continue withstep 26; otherwise, go to step 28.

With Camera

26. Using scissors, cut one urethane tape in half.Starting near the antenna end of the cable, wrap onehalf of urethane tape around the antenna cable at themeasurement shown.

QD22001AY

220 mm(8.7 in.)

ANTENNACABLE

URETHANE TAPEURETHANE TAPE(Cut in half.)

SECTIONVIEW

8 of 28 AII 52560

27. Attach masking tape to the front windshield at themeasurement shown. Go to step 31.

QD22003AY

MASKING TAPE

10 mm (0.4 in.) HEADLINER

FRONTWINDSHIELD

CAMERACOVER

CAMERACOVER

Without Camera

28. Using scissors, cut one urethane tape in half.Starting near the antenna end of the cable, wrap onehalf of urethane tape around the antenna cable at themeasurement shown.

QD22002AY

220 mm(8.7 in.)

20 mm(0.8 in.)

ANTENNACABLE

HALVES OFURETHANETAPE

URETHANE TAPE(Cut in half.)

SECTIONVIEW

29. Wrap one half of urethane tape around the antennacable at the measurement shown.


30. Attach masking tape to the front windshield at themeasurement shown.

QC11702AB

MASKING TAPE

20 mm (0.8 in.)

HEADLINER

FRONTWINDSHIELD

REARVIEWMIRROR

REARVIEWMIRROR

31. Attach the antenna.

• Fold the adhesive backing of the antenna asshown.

QB51401CH

ANTENNA

ADHESIVEBACKING


• Using isopropyl alcohol on a shop towel, cleanthe front windshield where the antenna willattach.

• Attach the antenna with masking tape. Adjustthe position of the antenna so there is equalspacing on both sides.

QB51404CH

Clean withisopropyl alcohol.

ANTENNA

MASKINGTAPE

HEADLINER

ANTENNA

Equal spacing on both sides.

MASKINGTAPE

Align.

FRONTWINDSHIELD

• Carefully remove the adhesive backing from theantenna, and attach the antenna to the frontwindshield. Press and hold the antenna firmly inplace for 30 seconds.

• Remove the masking tape.

QB51405CH

ADHESIVEBACKING(Remove.)

ANTENNA

MASKING TAPE(Remove.)

(1409) 9 of 28

32. Gently pull down the headliner, and tuck the antennacable under the headliner. Be careful not to creasethe headliner.

QC50904AB

ANTENNACABLE

HEADLINER

VEHICLEPANEL

ANTENNACABLE

SECTION VIEW

HEADLINER

33. Route the antenna cable down the driver’s A-pillaralong the vehicle harness.

QD22004AY

ANTENNACABLE

5 WIRE TIES

DRIVER’SA-PILLAR

VEHICLEHARNESS

34. Secure the antenna cable to the vehicle harness withfive wire ties.

10 of 28 AII 52560

35. Route the antenna cable down behind thedashboard.

QC50906AB

ANTENNACABLE

TOP VIEW

FRONTSTEERINGHANGER BEAM


Routing the Engine Starter Harness

36. Plug the three relays into the relay block on theengine starter harness.

QD22116AY

20A FUSELABEL

2 RELAYS

RELAY

20A FUSELABEL

FUSEBLOCK

RELAYBLOCK

ENGINE STARTERHARNESS

3A FUSELABELS

Clean withisopropyl alcohol.

37. Using isopropyl alcohol on a shop towel, thoroughlyclean the relay block and fuse block where the 3Afuse labels and 20A fuse labels will attach.

38. Attach the two 3A fuse labels and two 20A fuselabels to the relay block and fuse block on the enginestarter harness.

If the vehicle is Touring grade, continue with step 39;otherwise, go to step 42.

Touring Grade

39. Plug the engine starter harness 28-pin connector tothe engine starter harness 28-pin connector.

QD32802AY

ENGINE STARTERHARNESS28-PIN CONNECTOR

ENGINESTARTERHARNESS


40. Route the engine starter harness 28-pin connectorsupward as shown.

QD32803AY

ENGINE STARTERHARNESS28-PIN CONNECTORS

41. Push the engine starter harness 28-pin connectorsbetween the driver’s A-pillar and vehicle 28-pinconnectors as shown. Go to step 47.

QD32804AY

VEHICLE28-PIN CONNECTORS

ENGINESTARTERHARNESS28-PINCONNECTORS

FRONTDRIVER’SA-PILLAR

ENGINESTARTERHARNESS28-PINCONNECTORS

VEHICLE28-PIN CONNECTORS

TOP VIEW

(1409) 11 of 28

Except Touring Grade

42. Route the two 28-pin connectors of the enginestarter harness upward as shown.

QD22005BYENGINE STARTERHARNESS

STEERINGHANGER BEAM


43. Unplug the vehicle 28-pin connector.

Q0N1804CG

VEHICLE28-PINCONNECTOR


44. Route the engine starter harness 28-pin connectorsas shown, and plug the engine starter harness28-pin connector into the vehicle 28-pin connector.

12 of 28 AII 52560

45. Push the engine starter harness 28-pin connectorbetween the driver’s A-pillar and vehicle 28-pinconnector as shown.

Q0N1805BG

VEHICLE 28-PINCONNECTOR

ENGINESTARTERHARNESS28-PINCONNECTOR

TOP VIEW

FRONT


DRIVER’SA-PILLAR


46. Plug the vehicle 28-pin connector into the enginestarter harness 28-pin connector.


47. Secure the engine starter harness and the antennacable to the vehicle frame with one wire tie.

Q0N1806BG

VEHICLEHARNESS

WIRETIE


WIRETIE


VEHICLEFRAME

ANTENNA CABLE

ANTENNACABLE

48. Secure the engine starter harness and the antennacable to the vehicle harness with one wire tie.


49. Using isopropyl alcohol on a shop towel, clean thearea where the urethane tapes will attach.

QD62415AB

LEFT KNEEBOLSTER

URETHANETAPE(Cut.)

2 URETHANETAPES

Align.

FRONT


50. Using scissors, cut one urethane tape into threepieces. Attach two urethane tapes to the left kneebolster as shown.

(1409) 13 of 28

51. Using scissors, cut one urethane tape to themeasurements shown. Wrap the cut urethane tapearound the engine starter harness 5-pin connector.

QD32805AY



URETHANE SIDE VIEW

20 mm(0.8 in.)

25 mm(1.0 in.)

URETHANETAPE

FUSEBOX

14 of 28 AII 52560

52. Unplug the vehicle 5-pin connector from the fusebox, and plug it into the engine starter harness 5-pinconnector.

QD22101AY

FRONT VIEW

VEHICLE 5-PINCONNECTOR


FUSEBOX

FUSEBOX

Plug inhere.

UNLOCK LOCK13

12 2Push.Push.Pull.

53. Plug the remaining engine starter harness 5-pinconnector into the fuse box.NOTE: Check that the engine starter harness 5-pinconnector is securely connected to the fuse box5-pin connector. A loose connection can cause theengine to stall.


54. Secure the 5-pin connectors to the engine starterharness with one long wire tie.

QD22102BY

FUSEBOX

5-PINCONNECTORS

LONGWIRE TIE


55. Slide the other clip on the engine starter harnessonto the vehicle connector. Note the direction andthe orientation of the clip.

QD22103CY


CLIP

VEHICLECONNECTOR

FRONT


If the vehicle is equipped with the accessory fog lights, goto step 57; otherwise, continue with step 56.

56. Plug the engine starter harness 4-pin connector intothe fuse box. Go to step 59.

QD22104CY

FRONT VIEW

FUSEBOX

FUSEBOX

Plug inhere.

ENGINE STARTERHARNESS 4-PINCONNECTOR

(1409) 15 of 28

57. Unplug the fog light 4-pin connector from the fusebox, and plug it into the engine starter harness 4-pinconnector.

QD22105CY

FRONT VIEW

FUSEBOXFUSE

BOX

Plug inhere.


FOG LIGHTS4-PINCONNECTOR


58. Plug the remaining engine starter harness 4-pinconnector into the fuse box.

16 of 28 AII 52560

59. Unplug the vehicle 28-pin connector, and plug theengine starter harness 28-pin connector into thevehicle 28-pin connector.

QD22106CY

FRONT VIEW

FUSEBOX

FUSEBOX

ENGINE STARTER HARNESS28-PIN CONNECTOR


Plug in here.


60. Slide the clip from the engine starter harness 28-pinconnector onto the bottom of the fuse box, then plugthe remaining vehicle 28-pin connector into theengine starter harness 28-pin connector.

QD22107CY

FRONT VIEW

FUSEBOX

FUSEBOX

INSTALLPOSITION


FUSE BOX



61. Unplug the vehicle 2-pin connector, and plug theengine starter harness 2-pin connector into thevehicle 2-pin connector.

QD22108CY

FRONT VIEW

FUSEBOX

Plug in here.

VEHICLE2-PINCONNECTOR WIRE TIE

VEHICLEHARNESS

2-PINCONNECTORS


62. Plug the remaining vehicle 2-pin connector into theengine starter harness 2-pin connector.

63. Secure the 2-pin connectors to the vehicle harnesswith one wire tie.

(1409) 17 of 28

64. Unplug the vehicle 13-pin connector and vehicle12-pin connector.

QD32806AY

FUSE BOX



65. Remove the vehicle ground bolt.

QD32807AY

FUSE BOX

VEHICLEGROUNDBOLT

VEHICLEGROUNDTERMINAL

ENGINE STARTERHARNESSGROUND TERMINAL

66. Secure the engine starter harness ground terminalto the vehicle ground terminal with the vehicleground bolt just removed.

67. Re-plug the vehicle 12-pin connector and vehicle13-pin connector.

18 of 28 AII 52560

68. Secure the engine starter harness to the vehicleharness with one wire tie.

QD32808AY

FUSE BOX

WIRETIE


VEHICLEHARNESS

69. Secure the engine starter harness to the vehicleharness with two wire ties.

QD22109CY

FUSEBOX


VEHICLEHARNESS

2 WIRETIES


70. Route the engine starter harness under thedashboard and toward the steering wheel.

QD62416AB


FRONT

LEFT KNEEBOLSTER

HOLE

CLIPFRONT


71. Secure the engine starter harness to the hole in theleft knee bolster using the clip on the engine starterharness as shown.


72. Locate the white tape on the engine starter harness,and loosely secure the engine starter harness to thedashboard with one wire tie at the white tape.If the vehicle is already equipped with otheraccessory harness, loosely secure the enginestarter harness to the other accessory harness withone wire tie as shown.

QD22110AY

OTHER ACCESSORYHARNESS

WITH OTHERACCESSORY HARNESS

WHITE TAPE

WIRE TIE(Looselysecure.)

WIRE TIE(Looselysecure.)

WHITETAPE

HOLE

DASHBOARDENGINE STARTERHARNESS


(1409) 19 of 28

73. Route the engine starter harness up steering wheelas shown.

QD22111AY

ENGINESTARTERHARNESSWHITE

TAPE

SECTION VIEW

VEHICLEHARNESS

2 WIRETIES

VEHICLEHARNESS


WIRE TIE

74. Align the white tape on the engine starter harnesswith the vehicle clip, and secure the engine starterharness to the vehicle harness with two wire ties asshown.

20 of 28 AII 52560

75. Route the engine starter harness, and unplug thevehicle 10-pin connector from the wiper switch, andplug it into the engine starter harness 10-pinconnector.

QD22112AY



STEERINGWHEEL



WIPERSWITCH

76. Plug the remaining engine starter harness 10-pinconnector into the wiper switch.


77. Secure the 10-pin connectors and engine starterharness to the vehicle harness with two wire ties.

QD22113AY

VEHICLEHARNESS

2 WIRETIES


Do not undue strain to the10-pin connector cord.

10-PINCONNECTORS

VEHICLECLIP


78. Route the engine starter harness, and unplug thevehicle 12-pin connector from the combination lightswitch, and plug it into the engine starter harness12-pin connector.

QD22114AYENGINE STARTERHARNESS

VEHICLE12-PIN CONNECTOR

COMBINATIONLIGHT SWITCH


79. Plug the remaining engine starter harness 12-pinconnector into the combination light switch.

(1409) 21 of 28

80. Align the white tape on the engine starter harnesswith the vehicle clip, and secure the engine starterharness to the vehicle harness with two wire ties.NOTE: Move the steering wheel up and downthrough its full adjustment range and make sure theconnectors and harness are not being stretched.

QD22115BY

VEHICLEHARNESS

2 WIRE TIES

Do not undue strain to the12-pin connector cord.

VEHICLECLIP

WHITETAPE


22 of 28 AII 52560

81. Route the antenna cable along the engine starterharness as shown.

QD62417AB


FRONT

LEFT KNEEBOLSTER WIRE TIE

(Loosely secure.)

ANTENNACABLE

WIRETIE

ANTENNACABLE

WIRETIE

VEHICLEHARNESS

DASHBOARD

FUSEBOX

82. Secure the antenna cable to the engine starterharness with two wire ties.

83. Loosely secure the antenna cable to the dashboardwith one wire tie loosely installed in step 72.


Installing the Control Unit

84. Using isopropyl alcohol on a shop towel, clean thearea where the urethane tape will attach.

Q0N2305AG

URETHANETAPE

VEHICLE UNIT Clean withisopropyl alcohol.

85. Attach one urethane tape to the vehicle unit asshown.

86. Plug the antenna cable connector and the enginestarter harness 28-pin connector into the controlunit.

QC50917AB


CONTROLUNIT

ANTENNACABLECONNECTOR


87. Install the control unit bracket to the control unit.

QC50918AB

CONTROLUNIT

CONTROL UNITBRACKET

88. Secure the clip from the engine starter harness fuseblock, and the clip from the engine starter harnessinto the holes in the control unit bracket.

Q0N2308BG

CONTROL UNITBRACKET


HOLE

CLIP

HOLECLIP

FUSEBLOCK

(1409) 23 of 28

89. Remove the vehicle flange nut that secure thevehicle bracket.

QC50919AB

CONTROL UNITBRACKET

VEHICLEFLANGE NUT18.6 - 24.5 N·m(14 - 18 lbf·ft)

CONTROL UNITBRACKET

VEHICLEBRACKET

VEHICLEFLANGENUT

VEHICLEBRACKET

VEHICLEPANEL

CONTROLUNITBRACKET

Align.

90. Install the control unit bracket on top of the vehiclebracket and align the control unit bracket with theedge of the vehicle bracket. Reinstall the vehicleflange nut. Torque the vehicle flange nut to18.6 - 24.5 N·m (14 - 18 lbf·ft).

24 of 28 AII 52560

91. Secure the antenna cable and engine starterharness to the vehicle harness with one long wire tie.

QD22401AY


FRONT

LONGWIRE TIE

ANTENNACABLE

VEHICLEHARNESS

92. Bundle up the excess antenna cable, and secure it tothe dashboard with the one wire tie loosely installedin step 83.

QD22402AY

ANTENNA CABLE(Bundle up the excess.)

WIRE TIEDASHBOARD


93. Using isopropyl alcohol on a shop towel, thoroughlyclean the hood where the caution label will attach.

Q0N2011AG

ADHESIVEBACKING(Remove.)

CAUTIONLABEL

HOOD(Clean withisopropyl alcohol.)

94. Remove the adhesive backing from the caution label,and attach the caution label to the hood in the areashown.

95. Check that all wire harness and cables are routedproperly and that all connectors are plugged in.

96. Reinstall all removed parts.

97. Reconnect the negative cable to the battery.

98. Check the operation of the headlights and wipers.

99. Press and hold the radio power button for twoseconds to restore the radio and navi (if equipped)system functions.

100. Reset the clock on vehicle without navigation.

101. Proceed to the REMOTE ENGINE STARTERREGISTRATION (Page 25) and Check theoperation of the Remote Control Engine Starter(Page 28).


REMOTE ENGINE STARTER REGISTRATION

NOTE: Register after making sure the HDS has beenupgraded to the latest version as described in the ServiceNews.

1. Acquire the PCM Code from the Interactive Network.

QC31909AC

CAR ICON

2. Connect the HDS/MVCI tester to the OBD II data linkconnector, then turn the engine switch to the on (II)position.

3. Start the HDS, and click the car icon.

4. Input the VIN and other required information into theHDS, then click the check button.

QB32102BH

Input the VIN and otherrequired information. CHECK BUTTON

5. Select Honda Systems, then click the check button.

(1409) 25 of 28

QB32103AH

SelectHonda Systems.

CHECK BUTTON

6. Select R/C ENG STARTER and click the checkbutton.

QB32104AH

SelectR/C ENG STARTER.

CHECK BUTTON

26 of 28 AII 52560

7. Select REGISTER REMOTE CONTROL ENGINESTARTER UNIT, then click the check button.

QB32105BH

SelectREGISTER REMOTECONTROL ENGINESTARTER UNIT.

CHECK BUTTON

8. The following message will display: Obtain PCM-code (IMMOBILIZER PCM CODE) from iN. Thisvehicle’s VIN will be required to obtain thepassword. (USA) Click the check button.

QB32106AH

Obtain PCM-codemessage.

CHECK BUTTON


9. Input the PCM-code, then click the check button.NOTE: To ensure security, the PCM-code(password) is changed everyday, so it is impossibleto register the remote control engine starter if thedates of the PCM-code acquisition and registrationare different. The date of the HDS/MVCI testershould also be the same.

QB32107BH

Input the PCM-Code.

CHECK BUTTON

10. The following message will display: The registrationof the Remote Control Engine Starter Unit hasbeen completed. Turn the engine switch off.

QB32108CH

The registration of theRemote Control EngineStarter Unit has beencompleted.


11. The following message will display: Check thatengine can be started by the Transmitter. Clickthe check button.

QB32109CH

Check that engine can bestarted by the Transmitter.

CHECK BUTTON

12. Perform the Check the operation of the RemoteControl Engine Starter on page 28. Clear the DTC,then disconnect the HDS/MVCI.

(1409) 27 of 28

Check the operation of the Remote Control Engine Starter

Operating Conditions

• The hood is closed

• The shift lever is in park

• Turn the ignition switch off and the key is outside the vehicle

• All doors and tailgate closed and locked

Inspection

1. Press the engine/command button on the transmitter and release, within 2 seconds, press the lock/start button onthe transmitter.

The engine should start if all operating conditions are met.

Does the engine start?

Yes - Operation is normal.

No:

• Make sure all “Operating Conditions” are met.

• Check the engine starter harness connections.

• Connect the HDS/MVCI and check for an indicated failure.

(Refer to the appropriate Service Manual for details.)

B127121H

ENGINE/COMMANDBUTTON

UNLOCK/STOPBUTTON

RECEPTIONINDICATOR

CHECKINGINDICATOR

ENGINE STARTOPERATION

Blinking

ENGINERUNNINGINDICATOR

IN-CARTEMPERATURE*1

REMAININGIDLING TIME*1

*1 Only on vehicles equipped with the automatic climate control.This indicator is displayed for some vehicles among them.

LOCK/STARTBUTTON

2. Press the engine/command button on the transmitterand release, within 2 seconds, press the unlock/stopbutton. The engine should stop.

Does the engine stop?


No - Check the engine starter harness connections.

3. After the engine has stopped, start the engine again,and check that the engine stops after each of thefollowing conditions:

NOTE: After each test the ignition key must be cycled, or thedriver’s door must be opened and closed.

• Move the shift lever out of the P position.

• Unlock or open the doors or the tailgate.

• Open the hood.

• Turn the engine switch.

• Press on the brake pedal.

Does the vehicle system stop after each of these tests?


No - Check the engine starter harness connections.

4. Check that the power windows and the moonroof do not function, and the shift lever does not move to any positionwhen the vehicle system is started with the transmitter.

5. Start the vehicle system again, press the engine/command button on the transmitter two times, and check thevehicle condition on the display.

6. Check the operation of the transmitter when the vehicle is 120 m (400 ft.) away and in direct sight.

7. Press the unlock/stop button on the transmitter and verify that the doors unlock. Press the lock/start button, andverify that the doors lock.

8. Check that the engine can start by the vehicle key and that the wiper and the headlight can be operated normally.

28 of 28 AII 52560 (1409) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.

Documents

INSTALLATION VERSION 1 2015 CR-V INSTRUCTIONS ......2015 CR-V SEP 2014 PARTS LIST Remote Control Engine Starter Unit Kit P/N 08E91-T2A-100C Transmitter Control unit Antenna ID label