68
INSTALLATION, USE AND MAINTENANCE MANUAL UK English Snakky DOC. NO. H 180U 02 EDITION 3 2003-06

INSTALLATION, USE AND MAINTENANCE … operating manual.pdfinstallation, use and maintenance manual uk english snakky doc. no. h 180u 02 edition 3 2003-06

  • Upload
    trinhtu

  • View
    215

  • Download
    1

Embed Size (px)

Citation preview

INSTALLATION, USE AND MAINTENANCE MANUAL

UK English

Snakky

DOC. NO. H 180U 02

EDITION 3 2003-06

DICHIARAZIONE DI CONFORMITA’

DECLARATION OF CONFORMITY

DÉCLARATION DE CONFORMITÉ

KONFORMITÄTSERKLÄRUNG

DECLARACIÓN DE CONFORMIDAD

DECLARAÇÃO DE CONFORMIDADE

VERKLARING VAN OVEREENSTEMMING

INTYG OM ÖVERENSSTÄMMELSE

OVERENSSTEMMELSESERKLÆRING

YHDENMUKAISUUSTODISTUS

Dichiara che la macchina descritta nella targhetta di identificazione, è conforme alle disposizioni legislative delle direttive:89/392, 89/336, 73/23 CEE e successive modifiche ed integrazioni.

Declares that the machine described in the identification plate conforms to the legislative directions of the directives: 89/392, 89/336, 73/23 EEC and further amendments and integrations.

Déclare que l’appareil décrit dans la plaque signalétique satisfait aux prescriptions des directives: 89/392, 89/336, 73/23 CEE et modifications/intégrations suivantes.

Erklärt, daß das im Typenschild beschriebene Gerät den EWG Richtlinien 89/392,89/336, 73/23 sowie den folgenden Änderungen/Ergänzungen entspricht.

Declara que la máquina descripta en la placa de identificación, resulta conforme a las disposiciones legislativas de lasdirectivas: 89/392, 89/336, 73/23 CEE y modificaciones y integraciones sucesivas.

Declara que o distribuidor descrita na chapa de identificação é conforme às disposições legislativas das directivas CEE89/392, 89/336 e 73/23 e sucessivas modificações e integrações.

Verklaart dat de op de identificatieplaat beschreven machine overeenstemt met de bepalingen van de EEG richtlijnen89/392, 89/336 en 73/23 en de daaropvolgende wijzigingen en aanvullingen.

Intygar att maskinen som beskrivs på identifieringsskylten överensstämmer med lagstiftningsföreskrifterna i direktiven:89/392, 89/336, 73/23 CEE och påföljande och kompletteringar.

Det erklæres herved, at automaten angivet på typeskiltet er i overensstemmelse med direktiverne89/392, 89/336 og 73/23 EU og de senere ændringer og tillæg.

Forsikrer under eget ansvar at apparatet som beskrives i identifikasjonsplaten, er i overensstemmelse med vilkårene iEU-direktivene 89/392, 89/336, 73/23 med endringer.

Vahvistaa, että arvokyltissä kuvattu laite vastaa EU-direktiivien 89/392, 89/336, 73/23 sekä niihin myöhemmin tehtyjenmuutosten määräyksiä.

Valbrembo, 03/05/2001

ANTONIO CAVO

C.E.O

1© by NECTA VENDING SOLUTIONS SpA 0306 180-02

TABLE OF CONTENTS

English

INTRODUCTION PAGE 2IDENTIFICATION OF THE VENDING MACHINE PAGE 2

IN THE EVENT OF FAILURES PAGE 2

TRANSPORT AND STORAGE PAGE 2

USING THE VENDING MACHINE PAGE 3

POSITIONING THE VENDING MACHINE PAGE 3

WARNING FOR INSTALLATION PAGE 3

PRECAUTIONS IN USING THE MACHINE PAGE 3

WARNING FOR SCRAPPING PAGE 3

TECHNICAL SPECIFICATIONS PAGE 4ACCESSORIES PAGE 4

POWER CONSUMPTION PAGE 4

CHANGEABLE COMBINATION LOCK PAGE 5

LOADING AND CLEANING PAGE 6MAIN SWITCH PAGE 6

CONFIGURING THE SPIRALS PAGE 6

HYGIENE AND CLEANING PAGE 7

LOADING PRODUCTS PAGE 7

START-UP PAGE 8

NOISE LEVEL PAGE 8

INSTALLATION PAGE 9UNPACKING THE VENDING MACHINE PAGE 9

INSTALLING THE PAYMENT SYSTEM PAGE 9

CONNECTION TO THE POWER SUPPLY PAGE 10

CONTROLS AND INFORMATION PAGE 10INTERNAL COMPONENTS PAGE 11

MAIN SWITCH PAGE 11

DISPENSING COMPARTMENTMANUAL RELEASE PAGE 11

OPERATING MODES PAGE 12USER INTERFACE PAGE 12

NORMAL OPERATING MODE PAGE 12

FILLER MENU PAGE 12STATISTICS PAGE 13

PRICES BY SINGLE SELECTIONS PAGE 13

CHANGE TUBES CONTROL PAGE 13

SPECIAL SELECTIONS PAGE 13

TEST PAGE 14

GSM PRE-ALARMS PAGE 14

EVADTS TRANSFER PAGE 14

TECHNICIAN MENU PAGE 15PRESENT FAILURES PAGE 16

PROGRAMMING THE PARAMETERS PAGE 17

STATISTICS PAGE 22

TEST PAGE 23

GSM PAGE 24

MAINTENANCE PAGE 25

PRINTED BOARD FUNCTIONSAND INDICATOR LAMPS PAGE 25

CONFIGURING THE BOARD PAGE 25

SOFTWARE UPDATE PAGE 25

CONFIGURING THE TRAYS PAGE 26PRODUCT SPACERS PAGE 26

PRODUCT EJECTOR PAGE 26

REPLACING THE SPIRALS PAGE 26

REMOVING THE TRAYS PAGE 26

CHANGING THE NUMBER OF TRAYS PAGE 27

CHANGING THE TRAY CONFIGURATION PAGE 27

POWER SUPPLY UNIT PAGE 28

ACCESS TO THE COOLING UNIT PAGE 28

PROGRAMMING MENU PAGE 29

WIRING DIAGRAM PAGE 57

2© by NECTA VENDING SOLUTIONS SpA 0306 180-02

Introduction

This technical documentation is part and parcel of thevending machine and must always follow the machinein case it is moved or transfer of ownership, so as toallow consultation by different operators.

Before starting installation and using the machine, it is firstnecessary to carefully read and understand the instruc-tions contained in this manual, as they offer importantinformation on installation safety, operating instructionsand maintenance.

This manual is divided into three chapters.

The first chapter describes the loading and routine main-tenance operations which are carried out in areas of themachine accessible with simple use of the door key,without using any other tools.The second chapter contains the instructions for correctinstallation and all information necessary for optimum useof the machine.The third chapter describes maintenance operationswhich involve the use of tools to access potentially danger-ous areas.

The operations described in the second and thirdchapters must be carried out only by personnel whohave the specific knowledge of the machine function-ing from a point of view of electrical safety and healthregulations.

IDENTIFICATION OF THE VENDINGMACHINE AND ITS CHARACTERISTICS

Each machine is identified by its own serial number,indicated on the rating plate attached inside the cabinet onthe right side.This plate (see figure below) is the only one acknowledgedby the manufacturer as the identification of the apparatus,and carries all the data which readily and safely givetechnical information supplied by the manufacturer. It alsoassists in the spare parts management.

Absorbed power

Operating voltage

Model

Product code

Current

Frequency

Serialnumber

IN THE EVENT OF FAILURES

In most cases, any technical problems are corrected bysmall repair operations; however, before contacting themanufacturer we recommend that this manual be readcarefully.Should there be serious failures or malfunctions, contactthe following:

NECTA VENDING SOLUTIONS SpAVia Roma 2424030 ValbremboItaly - Tel. +39 - 035606111

TRANSPORT AND STORAGE

To prevent any damage, special care should be takenwhen loading or unloading the vending machine.The machine can be lifted by a motor-driven or manualforklift truck, and the forks are to be placed underneath themachine from the side clearly indicated by the symbol onthe cardboard package.

Do not:

- overturn the vending machine;

- drag the vending machine with ropes or similar;

- lift the vending machine by its sides;

- lift the vending machine with slings or ropes;

- shake the vending machine.

The machine should be stored in a dry room where thetemperature remains between 0°C and 40°C.Avoid stacking machines one on top of the other andalways keep it upright as indicated by the arrows on thepacking.

Refrigeration system class Type and amount of refrigerant

Type

Fig. 1

3© by NECTA VENDING SOLUTIONS SpA 0306 180-02

USING THE VENDING MACHINE FORPACKAGED PRODUCTS

A different sale price can be set for each product selectionby the machine electronic control. The various functionsare programmed through the selection keypad without anyneed for additional equipment.All models are equipped with variable configuration trays,adding or removing dividers, spirals and ratiomotors; there-fore the machine can be easily suited to specific needs.All trays are preset for the operation of up to 6 selections(maximum setting).The selections are equipped with independent motors andspirals; each selection will continue its operation autono-mously even if the other selections are disconnected.

POSITIONING THE VENDING MACHINE

The vending machine is not suitable for outdoor installa-tion. It must be positioned in a dry room where the tempera-ture remains between 2°C and 32°C, and not where waterjets are used for cleaning (e.g. in large kitchens, etc.).The machine should be placed close to a wall.The ventilation system allows the back panel to be leanedagainst the wall, thus saving space, as air is drawn fromunder the machine and exhausted through a grille on theright-hand side. However, the grille must be completelyfree without obstructions to the airflow for at least 40 cm.If this were not possible, the spacer supplied with themachine must be fitted to ensure the required distancefrom the wall (see Fig. 2).

Warning!

Incorrect ventilation may compromise the proper func-tioning of the cooling unit.

The machine should be positioned with a maximum incli-nation of 2°.If necessary provide proper levelling by way of the adjust-able feet included.

WARNING FOR INSTALLATION

The machine installation and the following mainte-nance operations should be carried out by qualifiedpersonnel only, who are trained in the correct use ofthe machine according to the standards in force.

The machine is sold without payment system, thereforethe installer of such a system is responsible for anydamage to the machine or to things and persons caused byfaulty installation.

The integrity of the machine and compliance with thestandards of the relevant systems must be checked atleast once a year by qualified personnel.

PRECAUTIONS IN USING THE MACHINE

The following precautions will assist in protecting theenvironment:

- use biodegradable products only to clean the machine;

- adequately dispose of all containers of the productsused for loading and cleaning the machine;

- keep the machine away from heat sources;

- regularly check the condition of the door seal to limitany heat dispersion;

- limit as much as possible door opening time duringloading operations to avoid temperature increaseinside the cabinet and subsequent power consumption.

WARNING FOR SCRAPPING

Whenever the machine is to be scrapped, the laws in forceregarding environment protection should be strictly ob-served. More specifically:

- ferrous and plastic materials and the like are to bedisposed of in authorized areas only;

- insulating materials should be recovered by qualifiedcompanies.

- the gas inside the cooling unit, regardless of the type(see the identification plate), should be recovered byqualified companies by means of special equipment.

Fig. 2

1 - Securing holes2 - Spacer3 - Fastening screws

4© by NECTA VENDING SOLUTIONS SpA 0306 180-02

TECHNICAL SPECIFICATIONS

Power supply voltage 230 V~Power supply frequency 50 Hz

Absorbed power 345 W

Max. operating conditions:

Ambient temperature 32 °C

Relative humidity 65 %

Refrigeration system:

Compressor’s refrigeration output 320 W

Fan-forced evaporator

Programmable defrosting cycle

DIMENSIONS

Height 1700 mm

Width 701 mm

Depth 854 mm

Overall depth with door open 1335 mm

Weight 190 Kg

PAYMENT SYSTEMThe machine is supplied with all electrical prearrangementfor systems with Executive, BDV and MDB protocol, aswell as for installation of 24 V DC validators.Beside the coin mechanism housing, suitable space isprovided for the installation (optional) of the most widelyused payment systems.

SALES PRICES

A different programmable price can be set for each singleselection.

COIN BOXCover and lock are available as an optional feature.

CONTROLS AND SAFETY DEVICES

- Payment system compartment switch

- Timeout for power supply to dispensing motors

- Compressor overheating protection

- Line fuses

- Fuses on transformer primary and secondary windings

ACCESSORIES

A wide range of accessories can be installed on themachine, to vary its performance.The installation kits are supplied with their own installationand test instructions, which must be strictly observed toensure the machine safety.

Installation and the following testing operations mustbe carried out exclusively by personnel who have aspecific knowledge of the machine functions from apoint of view of electrical safety and health regula-tions.

POWER CONSUMPTION

The machine power consumption depends on many fac-tors, such as temperature and ventilation of the roomwhere it is installed, temperature of loaded products,internal temperature of the refrigerated box.Under average conditions, and namely:

- Ambient temperature: 20 °C

- Refrigerated box temperature: 8 °C

- temperature of loaded products(machine completely empty) 20 °C

the following power consumption levels resulted:

- Hourly stand-by power consumption 151 Wh

The above power consumption calculated from averagedata should only be taken as an indication.

Fig. 3

5© by NECTA VENDING SOLUTIONS SpA 0306 180-02

CHANGEABLE COMBINATION LOCK

Some machine models are fitted with a changeable com-bination lock.The lock is supplied with a silver colour key to be used fornormal opening and closing.The lock can be customised by means of a kit, available asaccessory, permitting changing of the lock combination.This kit includes a change key (black) for the current lockcombination as well as the change (gold) and use (silver)keys for the new combination.Sets of change and use keys with other combinations canbe supplied on request.Additional sets of use keys (silver) may be requested,indicating the combination stamped on the keys.Generally, only the use key (silver) is used, while thecombination change keys (gold) can be kept as spares.

Do not use the change key for normal opening, as itmay damage the lock.

Fig. 4

To change combination do as follows:

- open the machine door to avoid forcing the rotation;

- lightly lubricate the inside of the lock with a spray;

- insert the current change key (black) and rotate to thechange position (reference notch at 120°);

- remove the current change key and insert the changekey (gold) with the new combination;

- rotate to the close position (0°) and remove the changekey.

The lock will now have the new combination.

The keys with the old combination cannot be used forthe new combination.

6© by NECTA VENDING SOLUTIONS SpA 0306 180-02

Chapter 1LOADING AND CLEANING

MAIN SWITCH

When extracting the sliding compartment,a special switch(see Fig. 5) disconnects the power from the machineelectrical system to allow maintenance and cleaning op-erations in full safety.

The only parts that stay energised are those protectedby covers and carrying a plate with the warning “dis-connect the power before removing the cover”.

CONFIGURING THE SPIRALS

According to the size of the products to be dispensed, eachmachine can be fitted with a variable number of trays(maximum 6), product compartments and with dispensingspirals of different pitch.

Fig. 51 - Door opening handle2 - Trays3 - Lock4 - Product passage photocells (optional)5 - Product dispensing compartment6 - Main switch

Fig. 6

1 - Tray2 - Mobile walls3 - Right-hand spiral4 - Left-hand spiral

The spirals can be housed either in 152 mm compartments(two spirals, right-hand and left-hand, in each productholder) for large size products, or into 75 mm compart-ments (one right-hand spiral in each product holder) forsmall size products.When dispensing sticks of candies or similar products, it ispossibleto set the rotation of the spirals to 180° instead of 360° forthe 75 mm compartments and use a special right handspiral fitted with a divider (see Fig. 7), doubling the capacityof the compartments.It is possible to insert a divider in the already installedspirals (see Fig. 7).

Fig. 71 - 180° rotation spiral2 - DividerA - Spiral pitchB - Maximum product size

7© by NECTA VENDING SOLUTIONS SpA 0306 180-02

Fig. 8

1 - Tray groove2 - Product support

As standard feature or using special kits, the machine canbe equipped with small compartments, suitable for dis-pensing cans, plastic bottles up to 69 mm dia., 0.2 litreTetra-Paks.The compartments equipped in this way can be recog-nised by the shape of the product support bracket (see Fig.8).Some bottle types can be dispensed without using thesupports.Most bottles can be dispensed without using any specialaccessories, loading the bottles up side down, so that thecap slides in the compartment channel.

The spirals can be positioned with 22,5 degree steps bypulling them towards the front and rotating them in thedirection of ejection.Normally, the products can be dispensed without anyproblems when the spiral end is in the lower centre posi-tion.The maximum size (see Fig. 6) and the number of prod-ucts, the pitch and the direction of rotation of the spirals areshown in the following table.

A.mm

B.mm

°N

08 67 6

46 06 7

45 05 8

64 24 01

04 63 11

43 03 31

03 62 51

42 02 91

)°081(42 02 91+91

The machine is supplied with a table indicating the opti-mum setting for the different product types.The configuration can be changed following the indicationsof the relevant chapter.

HYGIENE AND CLEANING

According to current health and safety regulations, theoperator of vending machines is responsible for theirhygiene and cleaning.The vending machine is not suitable for outdoor installa-tion. It must be positioned in a dry room where the tempera-ture remains between 2°C and 32°C, and not where waterjets are used for cleaning.This vending machine should only be used to sell anddispense packaged products that do not need refrigerationto be preserved.Strictly comply to the producer’s specifications regardingstorage method and expiry date for each product.

Any other use is unsuitable and thus potentially dan-gerous.

It is advisable to use sanitising products (chlorine baseddetergent or similar) to clean all surfaces even if not indirect contact with food.

Under no circumstances should sprayed water beused.Some parts of the machine can be damaged by strongdetergents.The manufacturer declines all responsibility for damage topersons caused by the non-compliance with current regu-lations.At least every six months it is necessary to clean theventilation grilles of the cooling system using a vacuumcleaner or compressed air.

LOADING PRODUCTS

- Remove one tray at a time, lifting it and pulling it pastthe retaining slide. The upper trays will tilt downwardsto facilitate loading.

Fig. 9

8© by NECTA VENDING SOLUTIONS SpA 0306 180-02

- Load all products starting at the front, without insertingproducts with a temperature above 30°C, ensuring thatall spaces are filled. The bottom of the product mustrest at the bottom of the compartment with the labelfacing the window so that it can be identified.

All products should load easily, do not insert productswhich are too large for the space.

START-UP

Each time the machine is started, the number of traysconnected to the system are checked by the electroniccontrols and indicated on the display.Also the number of actually connected compartments ischecked.The display will indicate in a sequence information regard-ing:

- software version

- presence of dispensing detection photocells

- number of trays and compartments

- presence of dispensing compartment lock device

- internal sensor temperature.

NOISE LEVEL

The continuous, weighted equivalent acoustic pressurelevel is below 70 dB.

Fig. 10

- Push in the trays completely, ensuring that they gopast the retaining slide.

The sealed end of bags may be caught under the spiral,preventing the free fall of the product.Fold the seal towards the front of the unit and upwardsbefore inserting the product in the spiral.

More fragile products must be placed on the lowertrays to prevent damage when they drop.

Very thin products can be dispensed only using the specialspacer.

Fig. 11

1 - Product spacer2 - Brackets3 - Adjustment notches

9© by NECTA VENDING SOLUTIONS SpA 0306 180-02

Chapter 2INSTALLATION

The machine installation and the following mainte-nance operations should be carried out by qualifiedpersonnel only, who are trained in the correct use ofthe machine and are aware of the specific risks of suchoperations.

The machine is not suitable for outdoor installation, itmust be installed in a dry room where the temperatureremains between 2°C and 32°C.

It cannot be positioned where water jets are used forcleaning (e.g. in large kitchens, etc.).

The machine should be positioned with a maximuminclination of 2°.

The relative humidity must not exceed 65%.

UNPACKING THE VENDING MACHINE

After removing the packing, ensure that the machine isintact.If the vending machine is found to be damaged, immedi-ately inform the carrier and do not use the machine.

No packing elements (i.e. plastic bags, polystyrenefoam, nails, etc.) should be left within the reach ofchildren, as they are potentially dangerous.Packing materials must be disposed of in authorisedcontainers and the recyclable ones must be recovered byqualified companies.

If the vending machine had been laid down duringtransport, allow at least one hour before connecting itto the mains.

Fig. 12

1 - Coin chute fastening screw2 - Coin chute3 - Selector opening cam4 - Selector lever fastening screw5 - Coin mechanism securing holes6 - Coin mechanism compartment door7 - Coin mechanism8 - Coin slot chute9 - Coin return chute

INSTALLING THE PAYMENT SYSTEM

The machine is sold without payment system, there-fore the installer of such a system has sole responsi-bility for any damage to the machine or to things andpersons caused by incorrect installation.

Install the coin mechanism paying attention, according tothe type used, to:

- choose the most suitable securing holes;

- loosen the fastening screw and adjust the coin slotchute according to the coin mechanism opening;

- loosen the fastening screws and adjust the selectoropening lever;

- to aid installation the coin mechanism support platecan be lifted and rotated.

10© by NECTA VENDING SOLUTIONS SpA 0306 180-02

CONNECTING THE MACHINETO THE POWER SUPPLY

The machine is designed to operate under a single-phase230 V~ voltage and is protected by T6.3 A fuses.Before making the connection, ensure that the ratingcorresponds to that of the power grid, and more specifi-cally:

- the supply voltage rating must be within the rangerecommended for the connection points;

- the main switch should be capable of withstanding thepeak load required, and at the same time ensureproper omnipolar disconnection from the power gridwith an opening gap of the contacts of at least 3 mm.

The switch, the power outlet and the plug must belocated in an easily accessible position.The electrical safety of the machine is ensured only whenit is correctly earthed according to the safety standards inforce.

This fundamental safety requirement must be dulyverified, and if in doubt the system must be carefullytested by qualified technicians.

The power supply cable is of the type with a fixed plug. Anyreplacement of the power cable (see figure) should bemade by qualified and suitably trained personnel onlyusing cables type HO5 RN - F or HO5 V V-F or H07 RN-F with a 3x1-1.5 mm2 section.

Fig. 13

1 - Lift cover2 - Cable clamp3 - Power supply cable

CONTROLS AND INFORMATION

The user controls and information are located on theoutside of the sliding compartment (see Fig. 14).The credit and all function messages are indicated on thedisplay.

Fig. 14

1 - Door opening handle2 - Advertising spaces3 - Prearrangement for bill accepter4 - Display5 - Prearrangement for key type payment systems6 - Coin slot/return.7 - Lock8 - Selection keypad9 - Glass front10 - Coin return flap11 - Product flap

Do not use adapters, multiple sockets and/or exten-sions.

THE MANUFACTURER DECLINES ALL RESPONSI-BILITY FOR ANY DAMAGE CAUSED BY NON-COM-PLIANCE WITH THE ABOVE MENTIONED PRECAU-TIONS.

The keypad contains a series of numbered keys. To selecta product, key in the double digit number corresponding tothe desired product.Key is used to cancel a selection already made.Keys and are not available to the user; they are usedonly for programming.

11© by NECTA VENDING SOLUTIONS SpA 0306 180-02

MAIN SWITCH

The power supply unit (see Fig. 28) is fitted with amicroswitch that, when opening the sliding compartment,disconnects the power from the machine electrical sys-tem,

except from the terminal board supporting the linecable, the line fuses and from the same switch area.

Before removing the cover from these parts (indicatedwith a specific plate) it is necessary to disconnect theexternal switch.

The power supply can be reconnected, if necessary, byinserting the special key supplied with the machine.

All operations which require the machine to be ener-gised with the door open must be carried out byqualified personnel who are aware of the specific risksof such condition.

DISPENSING COMPARTMENT MANUALRELEASE

Some models are fitted with a lock device in the dispens-ing compartment that is released through electric controlwhen a selection is made (see compartment lock param-eters).Should for any reason be necessary to open the compart-ment without electric power, do as follows:

- remove the last tray;

- remove the anti-theft grille;

- manually operate the lock device.

INTERNAL COMPONENTS

The evaporator assembly mounted on the cabinet shelfcomprises two fans, the evaporator, the air duct and awater retaining tray placed under the evaporator.The C.P.U. board (central processing unit) fitted inside thepayment system compartment controls the different func-tions of the vending machine.

Fig. 15

1 - Product dispensing compartment housing2 - Cooling unit condenser3 - Cooling unit evaporator4 - Cold air flow grilles5 - Removable grille cover6 - Tray guides7 - Removable payment system compartment8 - C.P.U. board9 - Coin mechanism support10 - Product passage photocells11 - Power supply unit12 - Payment system compartment door switch

The cooling unit is located in the lower part of the cabinet.When removing the cover of the last ventilation grille (seeFig. 15) the air circulation ensures a uniform temperatureinside the refrigerated box, between 9° and 12° C.When covering the ventilation grille, the temperatureinside the refrigerated box is differentiated between theupper three trays (12°-16°C) and the lower three trays (8°-10°C).The cooling unit is defrosted automatically every 6 hours.In any case, the timing is programmable.The power supply unit, mounted in the lower section of thecabinet, contains the relay card which activates the com-pressor, the protection fuses and the switch on the pay-ment system door.

12© by NECTA VENDING SOLUTIONS SpA 0306 180-02

OPERATING MODES

The machine control software has three different functionlevels, which are:

- normal operation;

- filler menu;

- technician menu.

According to the operating mode, the display and keypadfunctions change as described in the following para-graphs.

USER INTERFACE

The interaction between system and operator happensthrough the following components:

- Liquid Crystal Display (LCD), 2 lines x 16 characters.

- External keypad configured via software with numerickeys from 0 to 9, having with the following functions inthe in the filler and technician menus:

NORMAL OPERATING MODE

The machine is preset to “Normal operation” mode whenconnected to the power supply and the payment systemdoor is closed (see door switch - Fig. 24).The lighting is switched on and the messages for thecustomer are indicated on the display.

FILLER MENU

The machine is preset to “Filler menu” when pressing themenu access button (located on the CPU board- see Fig.17).The keys “ ” and “ ” scroll through the menu items, whichinclude:

“Statistics” Data reading and display

“Single Prices” Changing the price for oneselection

“Tubes control” Manual refill and release ofchange tubes

“Special selections” Virtual selectionsReturn of virtual priceTwo-motor selectionsPhotocell parameters

“Test” Test selectionMotor testAutotest

“GSM” Resetting pre-alarm counters

“EVADTS” Connection

If a menu is not enabled during programming, a title isdisplayed in the list but it cannot be accessed.

Price button Key is used to access directly the price/selectioncombination of time band 0, if the function is enabled in the“Programming” menu.

Fig.16

Numeric keys1 to 7 are used to select directly a menu item by keying inthe corresponding number shown in the summary tablesincluded in the appendix to this manual.

Next menu key :

“ ” is used to move to the next menu option.In the case of command management it varies the statusof Logical Data where required, or in the case of NumericData it writes the value 0.

Previous menu key :“ ” is used to move to the next menu option.In the case of command management it varies the statusof Logical Data where required, or in the case of NumericData it writes the value 8.

Enter key :

“ ” is used to move from a menu to a sub-menu or to entera command.

Exit key :

“ ” is used to move from a sub-menu to the higher levelmenu, or to exit from the current command.

13© by NECTA VENDING SOLUTIONS SpA 0306 180-02

STATISTICS

Data on the machine operations is stored in both generalcounters and relative counters, which can be reset withoutlosing total data.

PRINTConnect an RS232 serial printer having a Baud rate of9600, 8 data bit, no parity, 1 stop bit to the serial portlocated on the push button board to print all of the statis-tics, and namely:

Total

1 - counter by single selection;2 - counter by time bands;3 - failure counter;4 - coin mechanism data;5 - photocell errors;6 - motor errors;7 - dispensing compartment lock errors

Relative1 - counter by single selection;2 - counter by time bands;3 - failure counter;4 - coin mechanism data;5 - photocell errors;6 - motor errors;7 - dispensing compartment lock errorsThe hardcopy printout will also contain the machine infor-mation, and namely:- date/time of print- machine name- software version- operator code- machine code- Installation date.To connect the printer, do as follows:

- press the confirm print button “ ”, displaying themessage “Confirm?”;

- connect the printer before confirming;

- press the confirm button “ ” to start printing.

DISPLAYWhen pressing the confirm button “ ” the data describedin the paragraph “Printing the statistics” is sequentiallydisplayed.

RESETTING THE RELATIVE STATISTICS

Statistics can be reset for relative counters globally (alltypes of data) or selectively for:- selections- failures- coin mechanism data- photocell errors- motor errors- dispensing compartment lock errorsPress the confirm button “ ”, and the message “Confirm?”starts blinking.Press the confirm button “ ”, the message “Working” isdisplayed for a few seconds and all statistics are reset.

PRICES FOR SINGLE SELECTIONS

This function is used to change the sales price for eachselection according to the time band.Key is used to access directly the price/selectioncombination of time band 0, if the function is enabled in the“Programming” menu.

CHANGE TUBES CONTROL

By accessing the “Tube control” function the change tubescan be filled or released manually.Confirm refilling, and the display will indicate“Credit: ——” which is the value of money available inchange the tubes; insert the desired coin into the selectorand the display will indicate the value of money availablein the change tubes.When confirming releasing, it will be possible to decidewhich tube to release. Each time the confirm button “ ” ispressed, a coin is ejected from the active tube.

SPECIAL SELECTIONS

VIRTUAL SELECTIONS

This function is used to define a pair of selections that canbe sold at a price different from the sum of the twoselections, using a single selection number. 10 virtualselections can be programmed (70 to 79).

RETURN OF VIRTUAL PRICEThis function is used to define, in the event of failed seconddispensing in a virtual selection, not to cash the price of thesecond selection (only if an MDB payment system orvalidator are used). With other payment systems, it can bedecided whether or not return the entire amount.

SELECTIONS WITH TWO MOTORS

In order to dispense long products, dividers can be fittedso that two motors are used for each single selection.With this function the operation of two motors can becombined, specifying the selection number of the secondmotor.The first motor number will be the selection number, whilethe selection number of the associated motor will remaindisabled.

Important notice!

After a failure to the motors of these selections, themachine configuration procedure in the “Spiral/Selec-tion” menu must be followed.

14© by NECTA VENDING SOLUTIONS SpA 0306 180-02

DISPENSING DETECTION

The vending machine can be fitted (as standard feature oras optional according to the model) with a device that, bymeans of photocells, detects the passage of dispensedproducts.This device permits, in the event of failed detection of thedispensed product:

- set a rotation time for the spiral beyond the limit switch,to overcome any jamming;

- return or not the paid amount;

- block further selections for the involved spiral.

TEST

SELECTIONS

This function is used to simulate the normal dispensing ofproducts without inserting any money to check the func-tioning of the spiral rotation by pressing the selectionbuttons.

MOTOR TEST

It activates all motors in a sequence, indicating on thedisplay the number of the involved selection.

AUTOTEST

A function to check, in a semiautomatic manner, thecorrect operation of some devices is implemented in thesoftware.Some checks occur automatically, others need the manualoperation of the monitored component; button “ ” ispressed to go to the next check.The monitored devices are:

“Keypad”

Press the button requested on the display; if it workscorrectly the request for the next button is presented.

“Temperature”The value of temperature detected by the probe is dis-played.In the event of disconnection the value -11.0 is displayed. In the event of a short-circuit the value 41.0 is displayed.“ ” to advance.

“Buzzer”

A series of sounds is emitted.

“Compressor”The compressor is activated/disactivated using the “ ”and “ ” buttons.

“Selections”

All selections are activated in a sequence.

“Coin mechanisms”Checking that communication with the coin mechanismtakes place correctly and which validator lines are aet asbeing active.

“Photocells”

If the product detection device is present, the light beamreading and interruption are checked.

“Disp compt lock”If the device for locking the dispensing compartmentopening, use the “ ” and “ ” buttons to lock and unlock thecompartment opening.

GSM PRE-ALARMS

The control software can send, via GSM modem, a signalindicating an “ending product” signal, when there is only acertain (programmable) number of pieces or grams ofpowder of a given product left. With this function thecounters that control the pre-alarms aree reset.

EVADTS TRANSFER

When activating this function, the machine awaits theconnection with a device to acquire the EVADTS statis-tics.

15© by NECTA VENDING SOLUTIONS SpA 0306 180-02

TECHNICIAN MENU

Using the programming procedures described in thissection, it is possible to set all variables regarding ma-chine configuration.The machine is preset to “Technician menu” when press-ing the button from the filler menu.

N.B. By pressing again the button from the technicianmenu, the machine will return to “Filler” mode.

The keys “ ” and “ ” scroll through the technician menuitems, which include:

Failures Read FailuresReset failuresMotor errorsMotors statusReset motor errors

Prog. parameters Cash PricesCoin mechanismsDecimal pointMaster/SlaveBonus

Spirals/sel. SpiralsPhotocellsDisp compt lock

Cold param. TemperatureDefrostingCooling unit

Display LanguageUser messagesPromotional messagePersonalised stringsDisplay countersContrast control

Miscellaneous PasswordEnergy savingMenu masking

Statistics Display partialTotal

Delete PartialTotal

Display relative partialTotal

Delete relative partialTotal

Display at start-up

Print relative partialTotal

Delete PartialTotal

Test Complete selectionsMotor testAutotest

Miscellaneous Machine info Installation dateMachine codeOperator code

Initialising

EVADTS Pass codeSecurity codeConnection

GSM Pin code

Pre-alarms ThresholdsCountersThreshold association

Bank Number

16© by NECTA VENDING SOLUTIONS SpA 0306 180-02

PRESENT FAILURES

READING

When the “Failure” function is displayed, press the confirmbutton “ ” to display the present failures.If no failures are currently present, after pressing theconfirm button “ ” the message “End failures” will bedisplayed.The monitored failures are:

CompressorThe machine is locked if the compressor runs non-stop formore than 24 hours.

Coin mechanism

The machine is locked if it receives a pulse longer than 2seconds on a validator line or the communication with theserial coin mechanism does not take place for more than30 seconds (Executive protocol) or 75 seconds (BDVprotocol).

RAM DataOne or more areas of the RAM contain wrong data whichwas corrected with the default values.The machine will continue to function, but it would beadvisable to initialise as soon as possible.

Probe

The machine is locked after 5 minutes if the internaltemperature sensor is disconnected; the display will indi-cate a temperature of -11° C.The machine is locked after one hour if a sensor shortcircuit is detected; in this case the display will indicate atemperature of +41° C.

Motor errorsWith this function the failed motors are displayed forapproximately 1 second.Scrolling through all failed motors is automatic.

Dispensing compartment lockWhen the function “unlock compartment with dispensing”and the parameter “out of service if open” are active, themachine will lock if the locking device of the dispensingcompartment remains blocked when closed or it does notclose within the programmed time.

Motors status

This function is used to read the last failure that occurredin each spiral, even if the machine configuration has anempty position.A motor can be in una of the following conditions:

- motor functioning;

- motor not present; when the motor is not detected atmachine start-up.

- motor disconnected; when a motor detected at ma-chine start-up is not detected during a selection.

- motor blocked; when the positioning button is notoperated within the “timeout”.

- empty spiral; when, with the dispensing control in-stalled, no dispensed product is detected.

Note:

By restarting the machine any motors with errors aredetected as not present.

RESETBy confirming this function all current failures will be reset.

17© by NECTA VENDING SOLUTIONS SpA 0306 180-02

PROGRAMMING PARAMETERS

CASH

This set of functions controls all parameters regarding thepayment systems and the sales prices.

SELECTION PRICESFour different prices can be set for each selection accord-ing to the programmed time bands for when the time tableoption is set.For each of the 4 time bands prices (0 to 65,535) can beprogrammed globally (same price for all selections) or forthe single selections.Should the majority of products be sold at the same price,it will be convenient to set the price globally and thenchange the figure of the selections with different prices.

TIME BANDS

Four programmable time bands are provided for sellingproducts at different prices.The time periods are programmable for beginning and endtime by hours (00 to 23) and minutes (00 to 59).If the values for start and end of the time band are set to00.00 the time period is disabled.The reference time is kept by an internal clock, program-mable as:day/month/year week-day 1-7and thenhour/minutes/seconds.

COIN MECHANISMS

It is possible to decide which of the payment systemprotocols available are to be enabled for the functions.The available payment systems are:

- Executive

- Validators

- BDV

- MDB

By selecting one of the systems it is possible to control itsfunctions.

EXECUTIVE

The following payments systems are available for theExecutive system:

- Standard

- Price Holding

- Coges

- U-Key

VALIDATORSWhen the “Validat. Lines” (line setting) function of the“technician” menu is displayed, the value of the 6 validatorcoin lines, A to F, can be changed.

BDVThe BDV protocol menus are used for defining the follow-ing functions:

Type of vending

Setting the operating mode for multiple or single dispens-ing. With multiple dispensing, the change is not automati-cally returned after a successful selection, however thecredit is available for further selections. When pressingthe coin return button, the available credit is returned if itsvalue is lower than the maximum change value.

Change controlThis function enables/disables the return of credit if noselections are made.If enabled, this function allows the return of coins even ifthe first selection was not dispensed.If however a selection fails for any reason, the change willbe returned if requested.Maximum creditThis function is used to define the maximum acceptedcredit.Maximum changeIt is possible to set a limit to the total amount of changereturned by the coin mechanism when pressing the coinreturn button or after a single dispensing serving.Any credit exceeding the amount programmed with thisfunction will be cashed.

Accepted coins

It is possible to define which, among the coins recognisedby the validator, are to be accepted.Check the label on the coin mechanism for the correct cointo value matching, indicating the position of the coins.

Not accepted coins

This function programs the rejection of coins when in“exact amount” mode.Check the label on the coin mechanism for the correct cointo value matching, indicating the position of the coins.

Dispensing buttons

This function enables or not the buttons on the coinmechanism used to release the coins in the change returntubes.

Value of “exact amount”

This value defines the combination of empty coin tubes,setting the coin mechanism in “exact amount” mode. Thepossible combinations of empty coin tubes are indicatedbelow.For greater simplicity, the combination is described withreference to tubes A, B and C, where tube A receives thelower value coins and tube C the greater value coins.

18© by NECTA VENDING SOLUTIONS SpA 0306 180-02

0 = A or (B and C)1 = A and B and C2 = A and B only3 = A and (B or C)4 = A only5 = A or B only (default)6 = A or B or C7 = A or B only8 = A or C only9 = B and C only10 = B only11 = B or C only12 = C only

C.P.C. device

It dialogues with the coin mechanism if devices are in-stalled or removed from the serial interface (C.P.C.-typedevices - the monitoring unit is always enabled by default).

Minimum level of tubes

It brings forward the “Insert exact amount” message forthe user, by adding a number of coins between 0 and 15to the programmed number of coins, to set the “full changetubes” status.

Free Vend VMC

Most payment systems with the BDV protocol control thefree vend function.However, there are some payment systems without suchfunction.In this case, if free selections are to be dispensed, freevending must be enabled with VMC (vending machinecontrol, enabled by default) and the price of the selectionsmust be set to zero.

MDBThe MDB protocol menus are used for defining the follow-ing functions:

Type of vending

Setting the operating mode for multiple or single dispens-ing. With multiple dispensing, the change is not automati-cally returned after a successful selection, however thecredit is available for further selections. When pressingthe coin return button (if the function is enabled), theavailable credit is returned up to the maximum changevalue.

Change controlTo enable/disable the operation of the coin return button.Maximum creditThis function is used to define the maximum acceptedcredit.Maximum changeIt is possible to set a limit to the total amount of changereturned by the coin mechanism when pressing the coinreturn button or after a single dispensing serving.Any credit exceeding the amount programmed with thisfunction will be cashed.

Accepted coins

It is possible to define which, among the coins recognisedby the validator, are to be accepted when the changetubes are full.Check the coin mechanism configuration for the correctcoin to value matching.

Returned coinsIt is possible to define which, among the coins available inthe tubes, are to be used for returning the change. Thisparameter is active only with coin mechanisms that do notautomatically control the choice of tube to be used (Autochanger payout).Check the coin mechanism configuration for the correctcoin to value matching.

Accepted bills

It is possible to define which, among the bills recognisedby the reader, are to be accepted.Check the reader configuration for the correct bill to valuematching.

Minimum level of tubesThis function is used for setting the number of coins (0 to15) to determine the status of full change tubes and the“Insert exact amount” message for the user.

Accepted coins with “exact amount”

It is possible to define which, among the coins recognisedby the validator, are to be accepted when the machine isin the “exact amount” condition.Check the coin mechanism configuration for the correctcoin to value matching.

COMMON FUNCTIONS

Other menus are available, common to the three protocols,used for defining the following functions:

IMMEDIATE CHANGE

Normally, the amount of credit inserted for a selection iscashed after the machine sends the message “Selectionsuccessful”.When this function is enabled, disabled by default, thecash message is sent at the beginning of dispensing.

DECIMAL POINTPress the confirm button “ ” to display the position of thedecimal point, i.e.:

0 decimal point disabled

1 XXX.X

2 XX.XX

3 X.XXX

Press the confirm button “ ”, these values will startblinking and can then be modified as necessary.

19© by NECTA VENDING SOLUTIONS SpA 0306 180-02

MASTER/SLAVEThe machine control system is pre-arranged for the con-nection in a bank of vending machines using special kits.This permits the use of a single payment system for moremachines.In the event of installation in a bank of machines, it can beconfigured a “Master”, i.e. having control over the secondmachine, or as “Slave”, i.e. leaving the control to the othermachine.Although the machine can be used in either the master orslave functions, it is advisable to use the Snakky asmaster, thus taking advantage of the central push-buttonpanel and the easier opening of the doors.The master/slave function is not enabled by default.To enable the function, it must be defined which machineis master and which one is slave in the software of both theSnakky and the Kikko.If an Executive payment system in “Price Holding” modeis set in the master machine, the information must be setalso in the software of the slave machine.The payment system of the slave machine must always bedefined as “validator”.In the event of failed electrical connection, both machineswill display the message “failed communication”.

COMBINED SELECTIONS

A combined selection is intended as the association of twoselections, one from the Snakky and one from the Kikko,to the same number (80 to 89) sold at a single price.Since a numeric keypad is required for setting and control-ling the combined selections, the relevant menu is in-cluded only in the software of the Snakky permitting thecombination of a selection from the keypad (10 to 79) witha direct selection.Combined selections can be used either with the Snakkyas master and Kikko as slave (recommended configura-tion) or vice versa. If one of the two selections is notavailable, the combined selection is not dispensed. If theimmediate change option is not activated on the mastermachine, and the first selection fails, the whole amount isreturned. If the second selection fails, it will be possible todecide whether to keep or return the entire amount byactivating/deactivating the “Virtual change return” option.

RESET SLAVE

This function, which can be used only with the Snakky SL,resets the machine programming to a non-configuredstatus.This function is necessary only when the setting for theSnakky SL is to be changed.

MONITOR

This function is used for scrolling through all the informa-tion regarding a Snakky SL being connected.When switching on the slave with the display showing thisfunction, the display will indicate in a sequence all informa-tion on the slave regarding:

- software version

- type of slave (XX, 0XX, 9XX)

- presence of dispensing detection photocells

- number of trays and compartments

- presence of dispensing compartment lock device

- internal sensor temperature.

To exit the function it will be necessary to switch themaster machine off.

FREE VEND BONUS

This function, compatibly with the national laws, permitsthe dispensing of a free product every certain programma-ble number of sold selections. In any case the freeselection is random within the programmed number. Themachine emits an intermittent sound signal and the dis-play indicates the message “FREE selection”.

SPIRALS/SELECTIONS

This set of functions is used to define the selection controlparameters.

MACHINE CONFIGURATION

This function is used to detect and store the number andposition of the trays and of the selection motors.

VIRTUAL SELECTIONS

This function is used to define a pair of selections that canbe sold at a price different from the sum of the twoselections, using a single selection number. 10 virtualselections can be programmed (70 to 79).

RETURN OF VIRTUAL PRICE

This function is used to define, in the event of failed seconddispensing in a virtual selection, not to cash the price of thesecond selection (only if an MDB payment system orvalidator are used). With other payment systems, it can bedecided whether or not return the entire amount.

20© by NECTA VENDING SOLUTIONS SpA 0306 180-02

SELECTIONS WITH TWO MOTORSIn order to dispense long products, dividers can be fittedso that two motors are used for each single selection.With this function the operation of two motors can becombined, specifying the selection number of the secondmotor.The first motor number will be the selection number, whilethe selection number of the associated motor will remaindisabled.

Important notice!

After a failure to the motors of these selections, themachine configuration procedure in the “Spiral/Selec-tion” menu must be followed.

PRODUCT CODE

This function is used for assigning a 4-digit identificationcode to each selection for processing the statistics.

DIRECT SELECTIONSThe vending machine can be fitted (as standard feature oras optional according to the model) with a 5-button keypadto which allocate a group of selection.After enabling the direct selection function, it will bepossible to allocate a group of selections to each key byspecifying the start and end numbers of the series.The selections, as long as in a sequence, can be also fromdifferent trays. The products are dispensed alternatingfrom each of the spirals that are groupped in a directselection.All selections belonging to the same group must have thesame price.For correct safety management of the selections it isadvisable that also a dispensing detection device beinstalled in the machine.

PHOTOCELL PARAMETERS

The vending machine can be fitted (as standard feature oras optional according to the model) with a device that, bymeans of photocells, detects the passage of dispensedproducts.When this device is installed, the following can be moni-tored:

- Error before dispensing; when at the selection start thephotocell beam is not read.

- Error after dispensing; when the motor fails duringdispensing.

- Error for no product; when the device does not detectthe passage of a product during dispensing.

In these cases the machine can be programmed to:

- set a rotation time for each spiral for settling beyondthe normal rotation;

- return or not the paid amount;

- block further selections for the involved spiral.

DISPENSING COMPARTMENT LOCK PARAMETERS

The dispensing compartment can be fitted (as standardfeature or as optional according to the model) with a lockdevice.This function is used for deciding whether leaving thedispensing compartment “always free” or “unlock it withdispensing”.In “unlock with dispensing” mode the dispensingcompartmen hatch is unlocked only for a certain period oftime, programmable at between 1 and 10 minutes, aftereach product selection. In this case it is possible to enablethe function that places the vending machine out ofservice for a certain period of time, programmable atbetween 1 and 10 minutes, if the dispensing compartmenhatch stays open.The machine is placed out of service if the lock device isalways closed during dispensing.

REFRIGERATION PARAMETERS

The operation of the refrigeration system can be pro-grammed for the following functions.

TEMPERATURE

The machine internal temperature during normal opera-tion can be set directly in °C (8° to 20°C, 8°C by default).The temperature differential deviation defined with theprevious function for starting/stopping the cooling unit is2°C.

DEFROSTING

This function allows for a defrosting cycle (switching thecooling unit off, regardless of the temperature) of 20minutes. The time interval between cycles can be pro-grammed from 0 to 99 hours (set to 6 hours by default); thetime interval will be determined according to the relativehumidity and the frequency of door openings.With the timing set to 0 the function is disabled.

ENABLE COLD UNIT

The cooling unit operation can be disabled. The changewill apply when restarting the machine.

21© by NECTA VENDING SOLUTIONS SpA 0306 180-02

DISPLAY

This set of functions is used to manage the messagesindicated on the external display.

LANGUAGE

There is an option of language, selected among theavailable ones, to be used for the messages on thedisplay.

DISPLAYING MESSAGES FOR THE USERIt is possible to choose the kind of information to beindicated on the display during normal operation.The following information can be displayed:

- Internal temperature

- Time

It is possible to choose the language for the displayedmessages.

PROMOTIONAL MESSAGE

EnableWhen in this menu, press the confirm button “ ” to displaythe status of the message (enabled or disabled). Thestatus can then be changed using the “ ” and “ ” buttons.

Setting

The 2-line message can be written using the “ ” and “ ”buttons to scroll through the available characters.Press the confirm button “ ”, the first character will startblinking and can be modified.The message is stored by pressing button “ ”.

CUSTOMISING THE MESSAGESThe machine uses standard messages to give informationto the user during normal operation (e.g. “Ready”, “Take”etc.). When this function is enabled, the message can bechanged in the same manner as setting the promotionalmessage. Changes are stored as copies of the standardmessages.Therefore, if this function is disabled, the standard mes-sages will be displayed again, but the changed messagesare still stored.

DISPLAY THE SELECTION COUNTERS

This function is used to enable/disable the display of thetotal number of sales since the last statistic reset, duringthe start-up phase of the machine.

LCD CONTRAST CONTROLThis function is used for adjusting the display contrastfrom 5% to 99% (default).

MISCELLANEOUS

This set of functions contains some sub-menus, used lessfrequently, which permit control of the functions describedbelow.

PASSWORD

ENABLING THE PASSWORD

This function is used to enable the option of requesting thepassword to access the technician menu; the passwordrequest is disabled by default.

ENTERING THE PASSWORD

It is a 5-digit numeric code which is required to access thetechnician menu.The default value of this code is set to 00000.

ENERGY SAVING

This function, disabled by default, is used to suspendvending in certain hours.2 switch-of time bands can be programmed.

DISPLAYING THE FILLER MENU

This function is used to determine the filler menu optionsto be left active or to be disabled (ON/OFF):

- Statistics

- Single selection prices

- Change tubes control

- Special selections

- Test

- GSM connection

- EVADTS

The reference numbers of the menus do not change evenif some are disabled.

EXTERNAL LIGHTING

Setting whether or not the lighting lamps are to be switchedon when the machine is out of service or during the“Energy saving” time band.

22© by NECTA VENDING SOLUTIONS SpA 0306 180-02

STATISTICS

Data on the machine operations is stored in both generalcounters and relative counters, which can be reset withoutlosing total data.

PRINTING

Connect an RS232 serial printer having a Baud rate of9600, 8 data bit, no parity, 1 stop bit to the serial portlocated on the push button board to print all of the statis-tics, and namely:

Total1 - counter by single selection;2 - counter by time bands;3 - failure counter;4 - coin mechanism data;5 - photocell errors;6 - motor errors;

Relative

1 - counter by single selection;2 - counter by time bands;3 - failure counter;4 - coin mechanism data;5 - photocell errors;6 - motor errors;The hardcopy printout will also contain the machine infor-mation, and namely:- date/time of print- machine name- software version- operator code- machine code- Installation date.To connect the printer, do as follows:

- press the confirm print button “ ”, displaying themessage “Confirm?”;

- connect the printer before confirming;

- press the confirm button “ ” to start printing.

DISPLAY

When pressing the confirm button “ ” the data describedin the paragraph “Printing the statistics” is sequentiallydisplayed.

RESETTING THE STATISTICSStatistics can be reset for counters globally (all types ofdata) or selectively for:

Total

- selections- failures- coin mechanism data- photocell errors;- motor errors;

Relative- selections- failures- coin mechanism data- photocell errors;- motor errors;

Press the confirm button “ ”, and the message “Confirm?”starts blinking.Press the confirm button “ ”, the message “Working” isdisplayed for a few seconds and all statistics are reset.N.B.: when resetting the total statistics also the relativestatistics are reset.

BDV protocol Audit

The information regarding the coin mechanism indicatesthe actual currency of:

Aud. 1 Money in the tubesMoney present in the change tube that moment

Aud. 2 Money to the tubesMoney sent to the change tubes

Aud. 3 Money to the boxMoney sent to the coin box

Aud. 4 Return of changeTotal money returned

Aud. 5 Dispensed moneyTotal money dispensed manually

Aud. 6 ExcessExcess money. Extra amounts paid by the customer thatwere not returned (in the event there was no moneyavailable for return)

Aud. 7 Total salesTotal value of sales

Aud. 8 Exact changeValue of sales in the “no change” condition.

Aud. 9 Mixed dispensingTotal value of dispensing paid differently; for example alsoother types of payment (C.P.C., token).

Aud. 10 Manual loadingMoney inserted in the coin mechanism through the manualfilling function.

23© by NECTA VENDING SOLUTIONS SpA 0306 180-02

MDB protocol AuditAud. 1 Money in the tubesMoney present in the change tubes that moment

Aud. 2 Money to the tubesMoney sent to the change tubes

Aud. 3 Money to the boxMoney sent to the coin box

Aud. 4 Change returnTotal money returned

Aud. 5 ExcessExcess money. Extra amounts paid by the customer thatwere not returned (in the event there was no moneyavailable for return)

Aud. 6 Release tubesValue of coins dispensed with the “Tubes control” function

Aud. 7 Loading tubesValue of money cashed with the manual loading function

Aud. 8 Cash salesValue of total sales with cash money (coins + bills)

Aud. 9 Cashed billsValue of cashed bills

Aud. 10 Charge keyValue of money changed into the key

Aud. 11 Sales with keyValue of money cashed for dispensing with key

Aud. 12 Money dispensed manuallyValue of coins dispensed manually with the dispensingbuttons on the coin mechanism.

TEST

SELECTIONSThis function is used to simulate the normal dispensing ofproducts without inserting any money.Check the functioning of the motor rotation by pressing theselection buttons.

MOTOR TEST

It activates all motors in a sequence.

AUTOTESTA function to check, in a semiautomatic manner, thecorrect operation of some devices is implemented in thesoftware.Some checks occur automatically, others need the manualoperation of the monitored component; button “ ” ispressed to go to the next check.The monitored devices are:

“Keypad”

Press the button requested on the display; if it workscorrectly the request for the next button is presented.

“Temperature”The value of temperature detected by the probe is dis-played.In the event of disconnection the value -11.0 is displayed. In the event of a short-circuit the value 41.0 is displayed.“ ” to advance.

“Buzzer”

A series of sounds is emitted.

“Compressor”The compressor is activated/disactivated using the “ ”and “ ” buttons.

“Selections”

All selections are activated in a sequence.

“Coin mechanisms”Checking that communication with the coin mechanismtakes place correctly and which validator lines are aet asbeing active.

“Photocells”

If the product detection device is present, the light beamreading and interruption are checked.

“Disp compt lock”If the device for locking the dispensing compartmentopening, use the “ ” and “ ” buttons to lock and unlock thecompartment opening.

24© by NECTA VENDING SOLUTIONS SpA 0306 180-02

MACHINE INFORMATION

The machine can memorize a series of codes which willidentify it when retrieving statistics.More specifically the following can be stored:

- 6-digit operator code;

- 8-digit vending machine code which identifies themachine.

INSTALLATION DATE

This function is used to store the current date of system,if set correctly, as installation date.The date is printed when retrieving the statistics.

MACHINE CODEWhen the “Machine code” function is displayed the eight-digit numeric code identifying the machine can be changed(from the default 0).

OPERATOR CODE

When the “Operator code” function is displayed the six-digit numeric code identifying groups of machines can bechanged (from the default 0).

INITIALISING

When the “Initialise” function is displayed the vendingmachine can be initialised, selecting the “country” (in-tended as configuration type) and the language, restoringall related default data.This function should be used in the event of a memory dataerror or when the software version is replaced/updated.All statistic information will be reset.Press confirm button “ ”; the country and the language tobe used are requested, then the message “Confirm?” isdisplayed. Press confirm button “ ” a second time and themessage “Working” is displayed for a few seconds.

EVADTS CODES

The EVADTS (European Vending Association Data Trans-fer System) communication protocol has two codes foridentifying the machine and for recognising the datatransfer terminal:

PASS CODE

It is a four-digit alphanumeric code (0-9; A-F) that must bethe same as the one in the data transfer terminal to allowits identification.Press the confirm button “ ” and the code is displayed as“0000” regardless of the actual value; then press thecorrection button “ ” and the first digit will start blinking.Using the scrolling buttons, its value can be changed(during the change operation the value becomes visible).Press the confirm button “ ” and the next digit startsblinking.Press the confirm button “ ” after changing the fourthdigit; the value is stored and the display indicates “0000”again.

SECURITY CODEIt is a further alphanumeric code for reciprocal recognitionbetween machine and EVADTS terminal.Programming works as in the “Pass” code.ConnectionThis function places the machine in wait mode for connec-tion to retrieve data.

EVADTS CONNECTION

When activating this function, the machine awaits theconnection with a device to acquire the EVADTS statis-tics.

GSM

The control software can send, via GSM modem, a signalindicating a machine failure or an “ending product” “pre-alarm”, after dispensing a programmable number of se-lections.The machine is pre-set to handle 7 pre-alarms.The first five can be associated to spirals and the last 2 totrays.

PIN CODEThis function is used for programming the identificationcode that will be sent to the GSM modem (optional) whenswitching the machine on.

SETTING THE THRESHOLDS

This function is used for defining the number of piecesafter which a “ending product” pre-alarm is signalled viamodem.

RESET COUNTERSWith this function the counters that control the pre-alarmsaree reset.

THRESHOLD ASSOCIATION

This function is used for defining which spirals or trays toassociate to “pre-alarms” for “ending product”.By associating spiral 10 to pre-alarm N. 1 and setting thethreshold to 10 units with the “threshold setting” function,dispensing the tenth product from spiral 10 will generatea pre-alarm N. 1.By associating tray N. 5 to pre-alarm N. 6 and setting thethreshold to 30 units with the “threshold setting” function,dispensing the thirtieth product from tray 5 will generate apre-alarm N. 6.

MACHINE BANK NUMBERThe number in the bank of machines (1 to 7) identifies themachines that have the “slave GSM” function, thereforesending data of the “master” machine via modem.The number 0 identifies the machine that is connecteddirectly to the modem, i.e. the “master GSM”.

25© by NECTA VENDING SOLUTIONS SpA 0306 180-02

Chapter 3MAINTENANCE

The maintenance operations described in this chaptershould be carried out with the machine energised andtherefore by qualified personnel, who are trained in thecorrect use of the machine and are aware of the specificrisks of such condition.To energize the system with the open door, simply insertthe special key into the switch on the payment systemcompartment door (see Fig. 28).

Inside the machine, the only parts that stay energisedare those protected by covers and carrying a plate withthe warning “Disconnect the power before removingthe protective cover”.

Before removing such covers disconnect the machinefrom the power grid.

The integrity of the machine and compliance with thestandards of the relevant systems must be checked atleast once a year by qualified personnel.

PRINTED BOARD FUNCTIONSAND INDICATOR LAMPS

The C.P.U. (Central Processing Unit) board controls allusers set for the maximum configuration of the spiralcompartment and processes the input signals from thekeypad, the payment system and the cooling unit sensors.The card also houses some LEDs which, during themachine operation, give the following indications:

- Green LED (3): blinks during normal operation of theC.P.U. board;

- Yellow LED (4): glows when 5 V DC are detected;

- Red LED (7): glows when, for any reason, the softwareis reset.

CONFIGURING THE BOARD

This board is preset also for the MDB protocol.The 4 minidips for setting the SW2 coin mechanism (seeFig. 17) should all be set to OFF (Executive).

SOFTWARE UPDATE

The machine is fitted with a Flash EPROM which can beelectronically updated.By means of a special program and suitable system(Personal Computer or similar) the machine managementsoftware can be updated without replacing the EPROM.Warning!When downloading the software it is advisable to discon-nect the motor connectors from the CPU board (J1 andJ2)

Fig. 17

1 - J14 Coin mechanism power supply2 - J15 Board power supply3 - Green LED: run (DL2)4 - Yellow LED: 5 V DC (DL1)5 - J1 Connection for dispensing compartment lock6 - J2 Spiral motor control7 - Red LED: CPU reset (DL3)8 - J3 Input/output9 - J4 Not used10 - J5 Programmer (RS232)11 - J6 Photocells12 - J7 Can-Bus13 - Programming mode button14 - J8 Validators15 - J9 Probe16 - J10 LCD display17 - J11 Keypad18 - J16 Keypad19 - J12 MDB expansion20 - Coin mechanism setting Minidip (SW2)21 - J13 Expansion for BDV / EXE

26© by NECTA VENDING SOLUTIONS SpA 0306 180-02

CONFIGURING THE TRAYS

PRODUCT SPACERS

The spacers are used when loading “narrow” products.The spacers should be fitted to contain products, withoutblocking them, towards the right-hand side of the compart-ment, so that they stay upright. According to the type ofproducts, assess whether it is more convenient to use theshort or long side of the brackets and in which of the fiveadjustment notches to connect them.Pull the spacer towards the front to close the space andpush it back to open the space.There must be at least 3 mm between the spacer and theproducts.

Fig. 18

1 - Product spacer2 - Brackets3 - Adjustment notches

Fig. 19

1 - Spirals2 - Ejectors

PRODUCT EJECTOR

The ejectors, right-hand and left-hand, must be used forproducts packed in bags, such as potato crisps or similar.As they are hooked at the end of the spiral they push theproducts further out. If necessary slide the ejector alongthe spiral wire to locate the most appropriate positionaccording to the product being dispensed.

REPLACING THE SPIRALS

In order to change the number and the set-up of theproduct holders, proceed as follows:

- Slide out the concerned tray.

- Rotate the spiral in the opposite direction to the ejec-tion rotation, holding the plastic support flange still, toseparate the two parts and fit the other spiral.

- Fit the new spiral assembly proceeding in the oppositedirection, ensuring that the spiral is positioned correctly

Fig. 20

1 - Spiral2 - Plastic flange

Fig. 21

REMOVING THE TRAYS

To replace the trays proceed as follows:

- Slide out the tray to be modified;

- remove the electrical connector from the tray;

- lift the tray to unblock the retaining slide.

- To fit a new tray, proceed in the opposite way.

27© by NECTA VENDING SOLUTIONS SpA 0306 180-02

CHANGING THE NUMBER OF TRAYS

The vending machines are supplied with 6 trays.It is however possible to bring the number of trays to 5,proceeding as follows:

- Disconnect the plug from the power supply.

- Remove all trays from the machine.

- Move the guides (see Fig. 22) placed on the sidesupports, except the first ones at the bottom whichstay in the same position.

- Carry out the same operation for the connectors,placed at the bottom of the cabinet.

- Remove the pair of guides not used.

- Replace the 5 trays, ensuring that the connectors areinserted properly.

- Secure the removed cables, as not to be in the way ofother trays and cables.

- Reprogram the machine.

Fig. 22

1 - Tray connector2 - Tray guide

CHANGING THE TRAY CONFIGURATION

The configuration of the spirals on each tray can bechanged. To go from two selections with single spirals toone selection with double spirals, do as follows:

- Remove the tray to be modified.

- Remove the centre wall, pushing it towards the backand then lifting.

- Remove the spirals, and the flanges, from the twomotors.

- Disconnect the left-hand side motor from the cable andremove it from the tray. In its place, fit the bush and pinbush.

- Install the right-hand and left-hand spirals with thesame pitch onto the new flanges (right and left areidentical), fitted with a cogged wheel, and then connectthe right-hand one to the motor still on the tray and theleft-hand one onto the previously installed bushes. Thetwo cogged wheels must mesh.

- Remove the price labels and the product holders nolonger used, and if necessary update the price labelsstill in use.

- Program the new selections with the desired price.

- Test the modified selections, to be sure of their correctoperation.

Fig. 23

1 - Tray2 - Mobile walls3 - Right-hand spiral4 - Left-hand spiral

N.B.: The selection numbers are formed by two figures;the first figure refers to the tray number, counting from thetop (1-6), the second figure refers to the spiral number,counting from the left (0-5).The selection number to which the motor is connected willtherefore be formed by the tray number plus the wire codenumber.

28© by NECTA VENDING SOLUTIONS SpA 0306 180-02

Fig. 24

1 Line fuses2 Transformer primary winding protection fuse3 CPU board power supply connector4 Lamp connector5 Compressor and fan connector6 Transformer secondary winding protection fuse7 Transformer secondary winding protection fuse8 Payment system compartment switch

Fig. 25

1 Anti-intrusion grille2 Dispensing compartment3 Photocell support

Fig. 26

1 Evaporator2 Fan3 Condenser4 Dispensing compartment

POWER SUPPLY UNIT

Fuses, switch and connectors positioned at the front of thepower supply unit have the functions indicated below.

When replacing any fuses the power supply cablemust be disconnected from the mains.

ACCESS TO THE COOLING UNIT

If for any reason the cooling unit need to be accessed fromthe machine, do as follows:

- remove the last tray

- remove the anti-theft grille

- undo the fastening screws from the product dispensingcompartment and remove it

- For reassembly, proceed in the reverse order.

© by NECTA VENDING SOLUTIONS SpA 0306 180-02

29

Fill

er m

enu

- S

um

mar

y

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

DIR

EC

T A

CC

ES

S T

O C

HA

NG

EP

RIC

E O

F T

IME

BA

ND

0

With

the

prin

ter

conn

ecte

dpr

int

all d

ata

as d

ispl

ayed

TO

TA

L S

TA

TIS

TIC

S

Prin

t da

ta f

or:

Sel

ectio

nsT

ime

band

sF

ailu

res

Coi

n m

echa

nism

dat

aE

rror

ie f

otoc

ellu

leE

rror

e m

otor

iPr

intin

g...

Hea

din

g:

Cur

rent

dat

eM

achi

ne m

odel

Sof

twar

e ed

ition

Ope

rato

r co

deM

achi

ne c

ode

Inst

alla

tion

date

RE

LA

TIV

E S

TA

TIS

TIC

S

FILL

>1

Stat

istic

sFI

LL >

1.1

Prin

t sta

tistic

sFI

LL >

1.1.

1Pa

rtial

prin

tout

FILL

>1.

1.1.

xSe

lect

ions

Con

firm

?

Prin

t Sel

ectio

ns

Prin

ting.

..

Prin

t Sel

ectio

ns

FILL

>1.

1.2

Tota

l prin

tout

Con

firm

?

Tota

l prin

tout

Prin

ting.

..

Tota

l prin

tout

FILL

>1.

2Pr

int r

elat

ive

FILL

>1.

2.1

Parti

al p

rinto

utFI

LL >

1.2.

1.x

Sele

ctio

nsC

onfir

m?

Prin

t Sel

ectio

ns

Prin

ting.

..

Prin

t Sel

ectio

ns

FILL

>1.

2.2

Tota

l prin

tout

Con

firm

?

Tota

l prin

tout

Prin

ting.

..

Tota

l prin

tout

FILL

>1.

3D

ispl

ay s

tatis

tics

FILL

>1.

3.1

Dis

play

sel

. cou

nter

FILL

>1.

3.1.

1D

isp.

sin

gle

coun

ter

Dis

play

sal

es b

y si

ngle

sele

ctio

n fo

r ea

ch t

ime

band

and

tot

al

Dis

play

tot

al s

ales

by

sing

le s

elec

tion

TO

TA

L S

TA

TIS

TIC

S

Sele

ctio

n ##

Tim

e ba

nd #

= #

###

FILL

>1.

3.1.

2D

isp.

tota

l cou

nter

Sele

ctio

n ##

Tota

l = #

##

Dis

play

tot

al s

ales

inno

rmal

ope

ratio

n an

dte

st m

ode

FILL

>1.

3.2

Cou

nt. f

or ti

me

band

sTi

me

band

0÷4

Cou

nter

=

##

#

FILL

>1.

3.3

Dis

play

failu

res

© by NECTA VENDING SOLUTIONS SpA 0306 180-02

30

Fill

er m

enu

- S

um

mar

y

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

DIR

EC

T A

CC

ES

S T

O C

HA

NG

EP

RIC

E O

F T

IME

BA

ND

0

Mo

nit

ore

d f

ailu

res:

Com

pres

sor

Coi

n m

echa

nism

RA

M d

ata

Pro

be

Com

pres

sor

Cou

nter

=

##

#

FILL

>1.

3.2

Cou

nt. f

or ti

me

band

s

FILL

>1.

3.3

Dis

play

failu

res

CO

IN M

EC

HA

NIS

M D

AT

A(a

ccor

ding

to

prot

ocol

use

d)

Val

idat

ors

and

Exe

cutiv

eC

ashe

d an

d so

ld

BD

V A

udit

MD

B A

udit

FILL

>1.

3.4.

1Au

dit d

ata

FILL

>1.

3.4

Disp

. coin

mec

h da

ta

FILL

>1.

3.4.

2Di

splay

cas

h co

unte

r

Err.

befo

re d

isp.

Cou

nter

= #

##FI

LL >

1.3.

5D

isp.

pho

t. er

r. cn

t.

Ph

oto

cell

erro

rs:

Bef

ore

disp

ensi

ngA

fter

disp

ensi

ngP

rodu

ct n

ot d

etec

ted

Sele

ctio

n N

. ##

Cou

nter

= #

##FI

LL >

1.3.

6D

isp.

mot

. err.

cnt

.

Mo

tor

erro

r

FILL

>1.

4D

ispl

ay re

lativ

es

© by NECTA VENDING SOLUTIONS SpA 0306 180-02

31

Fill

er m

enu

- S

um

mar

y

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

DIR

EC

T A

CC

ES

S T

O C

HA

NG

EP

RIC

E O

F T

IME

BA

ND

0

Fill

er m

enu

- S

um

mar

y

Dis

play

sal

es b

y si

ngle

sele

ctio

n fo

r ea

ch t

ime

band

and

tot

al

Dis

play

tot

al s

ales

by

sing

le s

elec

tion

RE

LA

TIV

E S

TA

TIS

TIC

S

Dis

play

tot

al s

ales

inno

rmal

ope

ratio

n an

dte

st m

ode

FILL

>1.

4.1

Dis

play

sel

. cou

nter

FILL

>1.

4.1.

1D

isp.

sin

gle

coun

ter

Sele

ctio

n ##

Tim

e ba

nd #

= #

###

FILL

>1.

4.1.

2D

isp.

tota

l cou

nter

Sele

ctio

n ##

Tota

l = #

##

FILL

>1.

4D

ispl

ay re

lativ

es

FILL

>1.

4.2

Cou

nt. f

or ti

me

band

sTi

me

band

0÷4

Cou

nter

=

##

#

Com

pres

sor

Cou

nter

=

##

#FI

LL >

1.4.

3D

ispl

ay fa

ilure

s

FILL

>1.

4.4.

1Di

sp. c

oin m

ech

coun

t.FI

LL >

1.4.

4Di

sp. c

oin m

ech

data

FILL

>1.

4.4.

2Di

splay

cas

h co

unte

r

Mo

nit

ore

d f

ailu

res:

Com

pres

sor

Coi

n m

echa

nism

RA

M d

ata

Pro

be

CO

IN M

EC

HA

NIS

M D

AT

A(a

ccor

ding

to

prot

ocol

use

d)

Val

idat

ors

and

Exe

cutiv

eC

ashe

d an

d so

ld

BD

V A

udit

MD

B A

udit

FILL

>1.

5D

el. r

elat

ive

stat

s

Err.

befo

re d

isp.

Cou

nter

= #

##FI

LL >

1.4.

5D

isp.

pho

t. er

r. cn

t.

Ph

oto

cell

erro

rs:

Bef

ore

disp

ensi

ngA

fter

disp

ensi

ngP

rodu

ct n

ot d

etec

ted

Sel.

N. #

#C

ount

er =

###

FILL

>1.

4.6

Dis

p. m

ot. e

rr. c

nt.

Mo

tor

erro

r

© by NECTA VENDING SOLUTIONS SpA 0306 180-02

32

Fill

er m

enu

- S

um

mar

y

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

DIR

EC

T A

CC

ES

S T

O C

HA

NG

EP

RIC

E O

F T

IME

BA

ND

0

Fill

er m

enu

- S

um

mar

y

Del

ete

data

for

:S

elec

tions

Tim

e ba

nds

Fai

lure

sC

oin

mec

hani

sm d

ata

Pho

toce

ll er

rors

Mot

or e

rror

s

RE

LA

TIV

E S

TA

TIS

TIC

SFI

LL >

1.5.

1D

elet

e pa

rtial

FILL

>1.

5.1.

1D

elet

e Se

lect

ions

Con

firm

?

Del

ete

sele

ctio

ns

Wor

king

...

Del

ete

sele

ctio

ns

FILL

>1.

5.2

Del

ete

tota

lC

onfir

m?

Del

ete

Sele

ctio

ns

Wor

king

...

Del

ete

Sele

ctio

ns

FILL

>1.

5D

elet

e R

elat

ive

FILL

>2

Sing

le p

rices

Opt

ion

of c

hang

ing

sale

spr

ice

for

each

sel

ectio

n in

4tim

e ba

nds

FILL

>2.

xPr

ice

Band

#Se

lect

ion

Pric

e

##

##

BD

V o

nly

Man

ual c

hang

e tu

be r

efill

Man

ual t

ube

rele

asin

gR

elea

se tu

bes

Tube

A ÷

X

FILL

>3Tu

bes

cont

rol

Fill

tube

sC

redi

t:###

##FI

LL>3

.1Fi

ll tu

bes

FILL

>4Sp

ecia

l sel

ectio

ns

FILL

>3.2

Rel

ease

tube

sR

elea

se tu

bes

Wor

king

...

Ent

er n

umer

icva

lue

10

####

#

Sele

ctio

n 1

0Pr

ice

Ent

er n

umer

icva

lue

© by NECTA VENDING SOLUTIONS SpA 0306 180-02

33

Fill

er m

enu

- S

um

mar

y

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

DIR

EC

T A

CC

ES

S T

O C

HA

NG

EP

RIC

E O

F T

IME

BA

ND

0

Fill

er m

enu

- S

um

mar

y

FILL

>4Sp

ecia

l sel

ectio

nsFI

LL>4

.1Vi

rtual

sel

ectio

nsSe

lect

ion

num

.##

Sel.

## +

FILL

>4.2

Virtu

al p

rice

chan

geO

N/O

FF

Virtu

al p

rice

chan

ge

####

FILL

>4.

3Tw

o-m

otor

sel

ectio

n

FILL

>4.

4Ph

otoc

ell p

aram

.FI

LL >

4.4.

1Se

ttlin

g tim

e

FILL

>4.

4.2

Mon

ey re

turn

FILL

>4.

4.3

Empt

y se

l. co

ntro

l

Sele

ctio

n nu

m.

Tim

e (s

/100

) =

VIR

TU

AL S

EL

EC

TIO

NS

Set

ting

two

sele

ctio

ns (

10 t

o69

) in

a v

irtua

l one

(70

to 7

9)

ON

/OFF

Mon

ey re

turn

ON

/OFF

Empt

y se

l. co

ntro

l

FILL

>5Te

st

Sele

ctio

n

nn

+

00nn

Sel

ectio

ns 1

0 to

69

mm

num

ber

of c

ombi

ned

mot

orif

mm

= n

n th

e co

mbi

natio

nbe

twee

n th

e tw

o se

lect

ions

isca

ncel

led

Sele

ctio

n n

n

nn

+

mm

## ##

© by NECTA VENDING SOLUTIONS SpA 0306 180-02

34

Fill

er m

enu

- S

um

mar

y

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

DIR

EC

T A

CC

ES

S T

O C

HA

NG

EP

RIC

E O

F T

IME

BA

ND

0

Fill

er m

enu

- S

um

mar

y

FILL

>5

Test

FILL

>5.

1Te

st s

elec

tion

FILL

>5.

2M

otor

test

FILL

>5.

3Au

tote

st

Wai

t ple

ase

Sele

ctio

n nu

m.#

#

Con

firm

?

Keyp

ad te

st

Sele

ctio

n nu

m.#

#W

ait p

leas

e

The

sel

ectio

n nu

mbe

rch

ange

s au

tom

atic

ally

Keyp

ad te

stPr

ess

1 bu

tton

#

Whe

n pr

essi

ng t

he b

utto

n,th

e ne

xt b

utto

n is

pre

sent

edau

tom

atic

ally

Con

firm

?

Tem

pera

ture

test

Tem

pera

ture

test

Tem

p. =

12.

2 °C

Con

firm

?

Buzz

er te

stBu

zzer

test

Wor

king

...

Em

issi

on o

f a

serie

s of

soun

ds

Con

firm

?

Com

pres

sor t

est

Com

pres

sor t

est

ON

/OFF

OF

F

ON

Con

firm

?

Sele

ctio

n te

st

Wai

t ple

ase

Sele

ctio

n nu

m.#

#A

ll se

lect

ions

are

act

ivat

ed in

a se

quen

ce

© by NECTA VENDING SOLUTIONS SpA 0306 180-02

35

Fill

er m

enu

- S

um

mar

y

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

DIR

EC

T A

CC

ES

S T

O C

HA

NG

EP

RIC

E O

F T

IME

BA

ND

0

Con

firm

?

Coi

n m

ech

test

Failu

re li

st

Coi

n m

ech

test

WIT

H E

XE

CU

TIV

E O

R

BD

V C

OIN

ME

CH

AN

ISM

S

If th

e co

in m

echa

nism

com

mun

icat

es it

dis

play

s"O

K"

AL

TE

RN

AT

IVE

LY

WIT

H A

VA

LID

AT

OR

Con

firm

?

Coi

n m

ech

test

Coi

n m

ech

test A

ctiv

atin

g a

line

of t

heva

lidat

or A

to

F

Coi

n m

ech

test

Valid

. lin

e #

Line

tw

o re

mai

ns f

orap

prox

imat

ely

2 se

cond

s

Con

firm

?

Phot

ocel

l tes

tW

ITH P

HO

TO

CE

LL

S

DIS

CO

NN

EC

TE

D

AL

TE

RN

AT

IVE

LY

Phot

ocel

l tes

tAb

sent

Con

firm

?

Phot

ocel

l tes

t

Failu

re li

st

Phot

ocel

l tes

tIf

the

light

bea

m is

inte

rrup

ted

with

in 2

.5 s

econ

ds it

dis

play

s"O

K"

or Err

or n

o pr

oduc

tIf

a fa

ilure

is p

rese

nt:

Err

or a

fter

disp

ensi

ngE

rror

bef

ore

disp

ensi

ng

WIT

H P

HO

TO

CE

LL

S

© by NECTA VENDING SOLUTIONS SpA 0306 180-02

36

Fill

er m

enu

- S

um

mar

y

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

DIR

EC

T A

CC

ES

S T

O C

HA

NG

EP

RIC

E O

F T

IME

BA

ND

0

Con

nect

ion

FILL

>7.1

FILL

>7EV

ADTS

Attre

bder

e pr

ego

FILL

>7.1

FILL

>1St

atis

tics

Sele

ctio

n 10

Pric

e

=Se

lect

ion

Pric

e =

###

#

Ent

er a

num

eric

val

ue

Con

firm

?

Dis

p. c

ompt

. loc

kD

isp.

com

pt. l

ock

ON

/OFF

OF

F

ON

With

dis

pens

ing

com

part

men

t lo

ck p

rese

nt

10

####

Con

firm

?

Dire

ct k

eypa

d te

stD

irect

key

pad

test

Pres

s 1

butto

n

If a

num

eric

key

pad

is f

itted

Whe

n pr

essi

ng t

he b

utto

n,th

e ne

xt b

utto

n is

pre

sent

edau

tom

atic

ally

FILL

>6G

SMR

eset

pre

-ala

rmco

unte

rsC

onfir

m?

Del

ete

tota

l

Wor

king

...

Del

ete

tota

lR

eset

ting

pre-

alar

m c

ount

ers

Wai

ting

for

EV

AD

TS

conn

ectio

n

#

© by NECTA VENDING SOLUTIONS SpA

37

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

Tim

e sc

rolli

ng o

f pr

esen

tfa

ilure

s

Pos

sibl

e m

otor

con

ditio

ns:

- O

K-

Blo

cked

- D

isco

nnec

ted

- N

ot f

unct

ioni

ng-

Not

pre

sent

- E

mpt

y se

lect

ion

TEC

H >

1Fa

ilure

sTE

CH

>1.

1R

ead

Failu

res

TEC

H >

1.2

Res

et F

ailu

res

TEC

H >

2Pr

og. p

aram

eter

s

Mo

nit

ore

d f

ailu

res:

Com

pres

sor

Coi

n m

echa

nism

RA

M d

ata

Pro

be

Res

et F

ailu

res

Don

e!

TEC

H >

1.4

Mot

or s

tatu

sM

otor

num

. ##

TEC

H >

1.5

Res

et m

ot. e

rr.R

eset

mot

. err.

Failu

re n

ame

Con

firm

?

DIS

PL

AY F

AIL

UR

ES

TEC

H >

1.3

Mot

or e

rrors

TEC

H >

1.1

End

of F

ailu

res

Tim

e sc

rolli

ng o

f pr

esen

tfa

ilure

sFa

ilure

nam

e

Mot

or e

rrors

© by NECTA VENDING SOLUTIONS SpA

38

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

TEC

H >

2.1

Cas

hTE

CH

>2

Prog

. par

amet

ers

TEC

H >

2.1.

1.1

Sing

le p

rices

TEC

H >

2.1.

1Pr

ices

TEC

H >

2.1.

1.1.

1Pr

ice

Band

#

TEC

H >

2.1.

1.2

Glo

bal p

rices

TEC

H >

2.1.

1.2.

1Pr

ice

Band

#4

time

band

s pl

us b

and

0 (n

otim

e ba

nd s

et)

avai

labl

e w

ithdi

ffere

nt p

rices

for

eac

hse

lect

ion

Opt

ion

of c

hang

ing

sale

spr

ice

for

each

sel

ectio

n in

4tim

e ba

nds

Sele

ctio

nPr

ice

##

##

Ent

er n

umer

icva

lue

10

####

Sele

ctio

n 1

0Pr

ice

####

Pric

e Ba

nd #

Pric

e

TEC

H >

2.1.

1.3

Tim

e ba

nds

X +

1

X - 1

TEC

H >

2.1.

1.3.

1Se

t dat

e an

d tim

eD

ate:

dd/

mm

/yy

d#Ye

ar

X +

1

X - 1

Tim

e: h

h/m

m/s

sTi

me:

X +

1

X - 1

TEC

H >

2.1.

1.3.

2Ti

me

band

1-4

Star

t: hh

/mm

End:

hh/

TIM

E B

AN

DS

Whe

n co

nfirm

ing

the

blin

king

valu

es,

hour

and

min

ute

for

star

t an

d en

d of

tim

e ba

ndar

e en

tere

d on

e af

ter

the

othe

r.If

star

t an

d en

d va

lues

are

set

to 0

0.00

the

tim

e ba

nds

are

deac

tivat

ed.

## ## ##

© by NECTA VENDING SOLUTIONS SpA

39

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

AV

AIL

AB

LE C

OIN

ME

CH

AN

ISM

S

Val

idat

ors

Exe

cutiv

eB

DV

MD

B

TY

PE O

F V

EN

DIN

G

CH

AN

GE W

ITH

OU

T V

EN

D

TEC

H >

2.1.

2.1

Set C

oin

mec

hani

sms

TEC

H >

2.1.

2C

oin

mec

hani

sms

Coi

n m

ech

type

Type

of V

endi

ngTy

pe o

f Ven

ding

Max

imum

cre

dit

Valu

e =

####

#Va

lue

=

Max

imum

cha

nge

Valu

e =

####

#Va

lue

=

####

####

XXXX

+ 1

XXXX

- 1

XXXX

+ 1

XXXX

- 1

Sing

le/M

ulti

Cha

nge

butto

nO

NC

hang

e bu

tton

ON

ON

OFF

EX

EC

UT

IVE P

RO

TO

CO

LS

Sta

ndar

dP

rice

Hol

ding

Cog

esU

Key

Sid

a

AL

TE

RN

AT

IVE

LY

BD

V/M

DB

Val

idat

ors

Exe

cutiv

e

A to

F

Valid

ator

Line

Line

Valu

e##

##XX

XX +

1

XXXX

- 1

SE

TT

ING T

HE V

AL

UE O

F

VA

LID

AT

OR L

INE

S

ON

Exec

utiv

e

Prot

ocol

nam

e

Coin

mec

h nam

e

© by NECTA VENDING SOLUTIONS SpA

40

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

Coi

ns 1

to 1

6

Coi

n #

Acce

pted

coi

nsC

oins

1

Coi

ns 1

to 1

6

Coi

n #

Acce

pted

cha

nge

Coi

ns 1

Dis

p. b

utto

nsO

NBu

tton

Ena

ble

Dis

able

ON

OFF

0 =

A o

r (B

and

C)

1 =

A a

nd B

and

C2

= A

and

B o

nly

3 =

A a

nd (

B o

r C

)4

= A

onl

y5

= A

or B

onl

y (d

efau

lt)6

= A

or

B o

r C

7 =

A o

r B

onl

y8

= A

or

C o

nly

9 =

B a

nd C

onl

y10

= B

onl

y11

= B

or

C o

nly

12 =

C o

nly

Com

bina

tion

1-12

Exac

t cha

nge

eq.

Com

bina

tion

#

C.P

.C. d

evic

eO

NC

.P.C

. uni

tE

nabl

e

Dis

able

ON

OFF

Ena

ble

Dis

able

Yes

No

Ena

ble

Dis

able

Yes

No

Yes

Yes

© by NECTA VENDING SOLUTIONS SpA

41

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

Exac

t cha

nge-

give

r

Free

ven

d VM

CO

NBu

tton

Ena

ble

Dis

able

ON

OFFVa

lue

=XX

XX +

1

XXXX

- 1

Valu

e =

####

#

TEC

H >

2.1.

2.2

Imm

edia

te c

hang

eIm

med

iate

cha

nge

Ena

ble

Dis

able

ON

OFF

TEC

H >

2.1.

3D

ecim

al p

oint

2#

Poin

t pos

it. =

#N

ew p

osit.

=

X +

1

X - 1

Imm

edia

te c

hang

e at

sta

rt o

fdi

spen

sing

Cho

ices

are

:

No

mas

ter

Mas

ter

Sna

kky

Mas

ter

Kik

ko

No

Sla

veS

lave

Sna

kky

Sla

ve K

ikko

Sla

ve S

nakk

y S

L X

XS

lave

Sna

kky

SL

0XX

Sla

ve S

nakk

y S

L 9X

X

If an

Exe

cutiv

e P

rice

Hol

ding

syst

em is

set

on

the

mas

ter,

it m

ust

be s

et a

lso

on t

hesl

ave

ON

OFF

TEC

H>2

.1.4

Mas

ter/S

lave

TEC

H>2

.1.4

.2Sl

ave

Pr. h

old.

OFF

Dec

imal

poi

nt 0

to 3

ON

####

TEC

H>2

.1.4

.1

No

mas

ter

Slav

e 1 N

o Sl

ave

Slav

e2

No

Slav

e

TEC

H>2

.1.4

.2Sl

ave

Pr. h

old.

OFF

© by NECTA VENDING SOLUTIONS SpA

42

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

TEC

H>2

.1.4

.3C

ombi

ned

sele

ctio

ns

Com

bine

d se

lect

ions

80 to

89

1st

com

bine

d se

lect

ion

Sna

kky

10 to

79

2nd

com

bine

d se

lect

ion

Kik

ko01

to 1

6or S

lave

101

0 to

079

Sla

ve 2

910

to 9

76

Sel.

num

. 80

Sel.

##

+

TEC

H>2

.1.4

.4R

eset

Sna

kky

SLTE

CH

>2.1

.4.4

Res

et S

nakk

y SL

Whe

n sw

itchi

ng o

n on

e of

the

two

poss

ible

sla

ve m

achi

nes,

its d

ata

is r

eset

.A

t th

e en

d em

issi

on o

f a

soun

dsi

gnal

.

TEC

H>2

.1.4

.5M

onito

rTE

CH

>2.1

.4.5

Mon

itor

Whe

n sw

itchi

ng o

n on

e of

the

two

poss

ible

sla

ve m

achi

nes,

the

follo

win

g is

dis

play

ed:

- so

ftwar

e ed

ition

- ty

pe o

f sl

ave

(XX

, 0X

X,

9XX

)-

pres

ence

of

phot

ocel

ls-

num

ber

of t

rays

and

sel

ectio

ns-

pres

ence

of

lock

dev

ice

- in

tern

al t

empe

ratu

re.

TEC

H>2

.1.5

Bonu

s Ve

ndita

Sele

ctio

n nu

m.

Sel.

##

+ ##

##Se

lect

ion

num

. 80

Sel.

+

##

##

##

© by NECTA VENDING SOLUTIONS SpA

43

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

TEC

H >

2.1.

5Fr

ee v

end

bonu

sTE

CH

>2.

1.5.

1En

able

bon

usO

FF

ON

Bonu

s fre

quen

cyon

e ev

ery

##

# S

.#

If O

N t

he a

vera

ge n

umbe

r of

sele

ctio

ns (

0001

to

9999

)be

twee

n tw

o bo

nuse

s is

requ

este

d

TEC

H >

2.2

Sele

ct./s

pira

liTE

CH

>2.

2.1

Spira

l par

amet

ers

TEC

H >

2.2.

1.1

Mac

hine

con

fig.

Mac

hine

con

fig.

Con

firm

?

TEC

H>

2.2.

1.2

Virtu

al s

elec

tions

Sele

ctio

n nu

m.#

#Se

l. ##

+

TEC

H>

2.2.

1.3

Virtu

al p

rice

chan

geO

N/O

FF

Virtu

al p

rice

chan

ge

VIR

TU

AL S

EL

EC

TIO

NS

Set

ting

two

sele

ctio

ns (

10 t

o69

) in

a v

irtua

l one

(70

to 7

9)

Rea

ding

sel

ectio

ns t

hat

are

actu

ally

pre

sent

inth

e m

achi

ne

ON

####

© by NECTA VENDING SOLUTIONS SpA

44

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

TEC

H>

2.2.

1.5

Prod

uct c

ode

TEC

H>

2.2.

1.4

Two-

mot

or s

elec

tion

Sele

ctio

n

nn

+

00nn

Sel

ectio

ns 1

0 to

69

mm

num

ber

of c

ombi

ned

mot

orif

mm

= n

n th

e co

mbi

natio

nbe

twee

n th

e tw

o se

lect

ions

isca

ncel

led

Sele

ctio

n n

n

nn

+

mm

Sele

ctio

n n

nC

ode:

###

Sele

ctio

n

Cod

e:

####nn

Sel

ectio

ns 1

0 to

69

TEC

H >

2.2.

1.6

Dire

ct s

elec

tions

TEC

H >

2.2.

1.6.

1En

able

dir.

sel

.

TEC

H >

2.2.

1.6.

2Se

t dir.

sel

.

ON

/OFF

Enab

le d

ir. s

el.

Sel.

dir.

1=

num

sel

.

Sel.

dir.

= nu

m s

el.

##

Dire

ct s

elec

tions

1 to

5

Sel

ectio

n nu

mbe

r10

to 7

9

# ##

#

© by NECTA VENDING SOLUTIONS SpA

45

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

TEC

H>2

.2.3

Com

pt. l

ock

para

m.

TEC

H>

2.2.

3.1

Ope

ratin

g m

ode

TEC

H>

2.2

.3.2

Unl

ock

time

TEC

H>

2.2.

3.3

Tim

e ou

t of s

ervi

ce

Mod

eA

lway

s un

lock

ed

Unl

ocke

d up

on d

ispe

nsin

gfo

r ##

min

utes

##01

to

10 m

inut

es

Unl

ock

time

Dur

atio

n:

Tim

e ou

t of s

ervi

ceD

urat

ion:

##

UN

LO

CK D

ISP

EN

SIN

G

CO

MP

AR

TM

EN

T

01 t

o 10

min

utes

TEC

H>

2.2.

3.4

Out

of s

ervi

ce if

ope

nO

N/O

FF

Out

of s

ervi

ce if

ope

nO

ut o

f se

rvic

e if

the

com

part

men

t fa

ils w

hen

open

TEC

H>2

.2.2

Phot

ocel

l par

am.

TEC

H>

2.2.

2.1

Settl

ing

time

TEC

H>

2.2

.2.2

Mon

ey re

turn

TEC

H>

2.2.

2.3

Empt

y se

l. co

ntro

l

ON

/OFF

Mon

ey re

turn

ON

/OFF

Empt

y se

l. co

ntro

l

Sele

ctio

n nu

m.

Tim

e (s

/100

) =

####

Unl

ock o

n disp

.

© by NECTA VENDING SOLUTIONS SpA

46

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

TEC

H >

2.3.

1Te

mpe

ratu

re

TEC

H >

2.3.

3En

able

col

d un

it

TEC

H >

2.4

Dis

play

TEC

H >

2.3

Col

d pa

ram

eter

s

Ope

ratin

g te

mpe

ratu

re6

to 2

0°C

.9°

C b

y de

faul

t

Inte

rnal

tem

pera

ture

Tem

p. °

C =

##

TEC

H >

2.3.

2D

efro

stin

g

Def

rost

ing

inte

rval

0 to

99

hour

s6

hour

s by

def

ault

Def

rost

ing

inte

r.D

efr.

inte

r. =

##

ON

/OFF

Enab

le c

old

unit

TEC

H >

2.4.

1La

ngua

geLa

ngua

ge

Lang

uage

Italia

nG

erm

anE

nglis

hF

renc

hS

pani

sh

AV

AIL

AB

LE L

AN

GU

AG

ES

TEC

H >

2.4.

2U

ser d

ispl

ayN

o m

essa

ges

Inte

rnal

tem

pera

ture

Tim

e

PO

SS

IBL

E M

ES

SA

GE

S

TEC

H >

2.4.

3Pr

omo.

mes

sage

Use

r dis

play

Mes

sage

En. p

rom

o. m

essa

ge

ON

/OFF

TEC

H >

2.4.

3.2

Prog

. pro

mo.

mes

sage

Le

tter

scro

lling

in a

sequ

ence

(16

cha

ract

ers

per

line)

Nex

t le

tter

Nex

t m

essa

ge

CH

AN

GE 2

-LIN

E U

SE

R

ME

SS

AG

E

TEC

H >

2.4.

4D

ispl

ay c

ount

er

TEC

H >

2.4.

3.1

En. p

rom

o. m

essa

ge

Cha

nge

line

1

Line

1

Cha

nge

line

2

Line

2

© by NECTA VENDING SOLUTIONS SpA

47

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

TEC

H >

2.4.

4D

ispl

ay c

ount

erD

ispl

ay c

ount

er

ON

/OFF

TEC

H >

2.4.

5C

ontra

st c

ontro

lC

ontra

st c

ontro

lK

= (5

- 99

)

Dis

play

ing

the

gene

ral

coun

ter

upon

sw

itchi

ng o

nth

e m

achi

ne

##

Ent

er t

he p

erce

ntag

e va

lue

from

the

key

pad

TEC

H >

2.5

Mis

cella

neou

sTE

CH

>2.

5.1

Set p

assw

ord

ON

/OFF

Set p

assw

ord

Set p

assw

ord

Pass

wor

d: #

####

5-di

git

num

ber

to a

cces

s th

ete

chni

cian

men

u

TEC

H >

2.5.

2En

ergy

Sav

ing

Ener

gy S

avin

gX

+ 1

X - 1

Ener

gy S

av. P

aram

.Ti

me

band

1-4

Star

t: hh

/mm

End:

hh/

ON

/OFF

TEC

H >

2.5.

2.1

Ener

gy S

avin

g

Whe

n co

nfirm

ing

the

blin

king

valu

es,

hour

and

min

ute

for

star

t an

d en

d of

tim

e ba

ndar

e en

tere

d on

e af

ter

the

othe

r.If

star

t an

d en

d va

lues

are

set

to 0

0.00

the

tim

e ba

nds

are

deac

tivat

ed.

IF O

N

TEC

H >

2.5.

3M

aski

ng fi

ller m

enu

##

© by NECTA VENDING SOLUTIONS SpA

48

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

FIL

LE

R M

EN

U

TEC

H >

3St

atis

tics

Men

u na

me

ON

/OFF

Sta

tistic

sS

ingl

e pr

ices

BD

V t

ube

cont

rol

Spe

cial

sel

ectio

nsT

est

EV

AD

TS

con

nect

ion

TEC

H >

2.5.

3M

aski

ng fi

ller m

enu

TEC

H >

2.5.

4N

eon

out o

f ser

vice

Neo

n ou

t of s

ervi

ce

ON

/OFF

If O

N li

ghtin

g is

sw

itche

d of

fw

ith v

endi

ng m

achi

ne o

ut o

fse

rvic

e

TEC

H >

3.1

Dis

play

sta

tistic

sTE

CH

>3.

1.1

Dis

play

sel

. cou

nter

TEC

H >

3.1.

1.1

Dis

p. s

ingl

e co

unte

rD

ispl

ay s

ales

by

sing

lese

lect

ion

for

each

tim

e ba

ndan

d to

tal

Dis

play

tot

al s

ales

by

sing

lese

lect

ion

TO

TA

L S

TA

TIS

TIC

SSe

lect

ion

##Ti

me

band

# =

###

#

TEC

H >

3.1

.1.2

Dis

p. to

tal c

ount

erSe

lect

ion

##To

tal =

###

Dis

play

tot

al s

ales

by

sing

letim

e ba

nd

TO

TA

L S

TA

TIS

TIC

STE

CH

>3.

1.2

Dis

p. t.

ban

d co

unt.

Tim

e ba

nd #

Tota

l = #

##

TEC

H >

3.1.

3D

isp.

failu

re c

ount

er

© by NECTA VENDING SOLUTIONS SpA

49

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

Mo

nit

ore

d f

ailu

res:

Com

pres

sor

Coi

n m

echa

nism

RA

M d

ata

Pro

be

Com

pres

sor

Cou

nter

=

##

#

TEC

H >

3.1.

2C

ount

. for

tim

e ba

nds

TEC

H >

3.1.

3D

isp.

failu

re c

ount

er

CO

IN M

EC

HA

NIS

M D

AT

A(a

ccor

ding

to

prot

ocol

use

d)

Val

idat

ors

and

Exe

cutiv

eC

ashe

d an

d so

ld

BD

V A

udit

MD

B A

udit

TEC

H >

3.1.

4.1

Audi

t dat

aTE

CH

>3.

1.4

Disp

. coin

mec

h da

ta

TEC

H >

3.1.

4.2

Disp

lay c

ash

coun

ter

Err.

befo

re d

isp.

Cou

nter

= #

##TE

CH

>3.

1.5

Dis

p. p

hot.

err.

cnt.

Ph

oto

cell

erro

rs:

Bef

ore

disp

ensi

ngA

fter

disp

ensi

ngP

rodu

ct n

ot d

etec

ted

Sel.

N. #

#C

ount

er =

###

TEC

H >

3.1.

6D

isp.

mot

. err.

cnt

.

Mo

tor

erro

r

TEC

H >

3.2

Del

ete

stat

istic

s

© by NECTA VENDING SOLUTIONS SpA

50

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

Del

ete

data

for

:S

elec

tions

Tim

e ba

nds

Fai

lure

sC

oin

mec

hani

sm d

ata

Pho

toce

ll er

rors

Mot

or e

rror

s

DE

LE

TE S

TA

TIS

TIC

STE

CH

>3.

2.1

Del

ete

parti

alTE

CH

>3.

2.1.

xD

elet

e Se

lect

ions

Con

firm

?

Del

. sel

. cou

nter

Wor

king

...

Del

. sel

. cou

nter

TEC

H >

3.2.

2D

elet

e to

tal

Wor

king

...

Del

ete

Sele

ctio

ns

TEC

H >

3.2

Del

ete

Stat

istic

s

Del

ete

Sele

ctio

ns

Con

firm

?

TEC

H >

3.3

Dis

play

sta

tistic

sTE

CH

>3.

3.1

Dis

play

sel

. cou

nter

TEC

H >

3.3.

1.1

Dis

p. s

ingl

e co

unte

rD

ispl

ay s

ales

by

sing

lese

lect

ion

for

each

tim

e ba

ndan

d to

tal

Dis

play

tot

al s

ales

by

sing

lese

lect

ion

RE

LA

TIV

E S

TA

TIS

TIC

SSe

lect

ion

##Ti

me

band

# =

###

#

TEC

H >

3.3

.1.2

Dis

p. to

tal c

ount

erSe

lect

ion

##To

tal =

###

Dis

play

tot

al s

ales

by

sing

letim

e ba

nd

RE

LA

TIV

E S

TA

TIS

TIC

STE

CH

>3.

3.2

Dis

p. t.

ban

d co

unt.

Tim

e ba

nd #

Tota

l = #

##

TEC

H >

3.3.

3D

isp.

failu

re c

ount

er

© by NECTA VENDING SOLUTIONS SpA

51

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

RE

LA

TIV

E S

TA

TIS

TIC

S

Com

pres

sor

Cou

nter

=

##

#TE

CH

>3.

3.3

Dis

play

failu

res

TEC

H >

3.3.

4.1

Visu

al. A

udit

data

TEC

H >

3.3.

4Di

sp. c

oin m

ech

data

TEC

H >

3.3.

4.2

Disp

lay c

ash

coun

ter

Mo

nit

ore

d f

ailu

res:

Com

pres

sor

Coi

n m

echa

nism

RA

M d

ata

Pro

be

CO

IN M

EC

HA

NIS

M D

AT

A(a

ccor

ding

to

prot

ocol

use

d)

Val

idat

ors

and

Exe

cutiv

eC

ashe

d an

d so

ld

BD

V A

udit

MD

B A

udit

TEC

H >

3.4

Del

. rel

ativ

e st

ats

Err.

befo

re d

isp.

Cou

nter

= #

##TE

CH

>3.

3.5

Dis

p. p

hot.

err.

cnt.

Ph

oto

cell

erro

rs:

Bef

ore

disp

ensi

ngA

fter

disp

ensi

ngP

rodu

ct n

ot d

etec

ted

Sele

ctio

n N

. ##

Cou

nter

= #

##TE

CH

>3.

3.6

Dis

p. m

ot. e

rr. c

nt.

Mo

tor

erro

r

© by NECTA VENDING SOLUTIONS SpA

52

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

Del

ete

data

for

:S

elec

tions

Tim

e ba

nds

Fai

lure

sC

oin

mec

hani

sm d

ata

Pho

toce

ll er

rors

Mot

or e

rror

s

RE

LA

TIV

E S

TA

TIS

TIC

STE

CH

>3.

4.1

Del

ete

parti

alTE

CH

>3.

4.1.

xD

el. s

el. c

ount

erC

onfir

m?

Del

. sel

. cou

nter

Wor

king

...

Del

. sel

. cou

nter

TEC

H >

3.4.

2D

elet

e to

tal

Con

firm

?

Del

ete

Sele

ctio

ns

Wor

king

...

Del

ete

Sele

ctio

ns

TEC

H >

3.4

Del

ete

Rel

ativ

e

TEC

H>3

.5D

isp.

cnt

. at s

tart

ON

/OFF

Dis

p. c

nt. a

t sta

rtT

he n

umbe

r of

sel

ectio

nsm

ade

are

indi

cate

d on

the

disp

lay

at m

achi

ne s

tart

-up.

TO

TA

L S

TA

TIS

TIC

S

Prin

t da

ta f

or:

Sel

ectio

nsT

ime

band

sF

ailu

res

Coi

n m

echa

nism

dat

aP

hoto

cell

erro

rsM

otor

err

ors

Hea

din

g:

Cur

rent

dat

eM

achi

ne m

odel

Sof

twar

e ed

ition

Ope

rato

r co

deM

achi

ne c

ode

Inst

alla

tion

date

RE

LA

TIV

E S

TA

TIS

TIC

S

TEC

H >

3.6.

1Pa

rtial

prin

tout

TEC

H >

3.6.

1.1

Sele

ctio

nsC

onfir

m?

Prin

t Sel

ectio

ns

Prin

ting.

..

Prin

t Sel

ectio

ns

TEC

H >

3.6.

2To

tal p

rinto

utC

onfir

m?

Tota

l prin

tout

Prin

ting.

..

Tota

l prin

tout

TEC

H >

3.7

Prin

t rel

ativ

e

TEC

H >

3.6

Prin

t sta

tistic

s

TEC

H >

3.7.

2To

tal p

rinto

utC

onfir

m?

Tota

l prin

tout

Prin

ting.

..

Tota

l prin

tout

Prin

ting.

..

Prin

t Sel

ectio

ns

Prin

ting.

..

Con

firm

?

Prin

t sel

. cou

nter

TEC

H >

3.7.

1.x

Prin

t sel

. cou

nter

TEC

H >

3.7.

1Pa

rtial

prin

tout

TEC

H >

4Te

st

© by NECTA VENDING SOLUTIONS SpA

53

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

TEC

H >

4Te

stTE

CH

>4.

1Te

st s

elec

tion

TEC

H >

4.2

Mot

or te

stW

ait p

leas

e

Sele

ctio

n nu

m.#

#

Sele

ctio

n nu

m.#

#W

ait p

leas

e

The

sel

ectio

n nu

mbe

rch

ange

s au

tom

atic

ally

TEC

H >

4.3

Auto

test

Con

firm

?

Keyp

ad te

stKe

ypad

test

Pres

s 1

butto

n#

Whe

n pr

essi

ng t

he b

utto

n,th

e ne

xt b

utto

n is

pre

sent

edau

tom

atic

ally

Con

firm

?

Tem

pera

ture

test

Tem

pera

ture

test

Tem

p. =

12.

2 °C

Con

firm

?

Buzz

er te

stBu

zzer

test

Wor

king

...

Em

issi

on o

f a

serie

s of

soun

ds

Con

firm

?

Com

pres

sor t

est

Com

pres

sor t

est

ON

/OFF

OF

F

ON

Con

firm

?

Sele

ctio

n te

st

Wai

t ple

ase

Sele

ctio

n nu

m.#

#A

ll se

lect

ions

are

act

ivat

ed in

a se

quen

ce

© by NECTA VENDING SOLUTIONS SpA

54

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

Con

firm

?

Coi

n m

ech

test

Failu

re li

st

Coi

n m

ech

test

WIT

H E

XE

CU

TIV

E O

R B

DV

CO

IN M

EC

HA

NIS

MS

If th

e co

in m

echa

nism

com

mun

icat

es it

dis

play

s"O

K"

AL

TE

RN

AT

IVE

LY

WIT

H A

VA

LID

AT

OR

Con

firm

?

Coi

n m

ech

test

Coi

n m

ech

test A

ctiv

atin

g a

line

of t

heva

lidat

or A

to

F

Coi

n m

ech

test

Valid

. lin

e #

Line

tw

o re

mai

ns f

orap

prox

imat

ely

2 se

cond

s

Con

firm

?

Phot

ocel

l tes

tW

ITH P

HO

TO

CE

LL

S

DIS

CO

NN

EC

TE

D

AL

TE

RN

AT

IVE

LY

Phot

ocel

l tes

tAb

sent

Con

firm

?

Phot

ocel

l tes

t

Failu

re li

st

Phot

ocel

l tes

tIf

the

light

bea

m is

inte

rrup

ted

with

in 2

.5 s

econ

ds it

dis

play

s"O

K"

or Err

or n

o pr

oduc

tIf

a fa

ilure

is p

rese

nt:

Err

or a

fter

disp

ensi

ngE

rror

bef

ore

disp

ensi

ng

WIT

H P

HO

TO

CE

LL

S

Con

firm

?

Dis

p. c

ompt

. loc

kD

isp.

com

pt. l

ock

ON

/OFF

With

dis

pens

ing

com

part

men

tlo

ck p

rese

nt

© by NECTA VENDING SOLUTIONS SpA

55

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

TEC

H >

5M

isce

llane

ous

TEC

H >

5.1

Mac

hine

info

TEC

H 5

.1.1

Inst

alla

tion

date

Dat

e:##

/##/

##

d#C

onfir

m?

TEC

H>5

.1.2

Prog

. mac

hine

cod

e

TEC

H>5

.2In

itial

ise

DB

Initi

alis

e D

BIn

itial

ise

DB

Wor

king

...

Whe

n co

nfirm

ing,

the

inst

alla

tion

date

will

tak

e on

the

curr

ent

date

8-di

git

num

ber

iden

tifyi

ng t

hem

achi

ne

TEC

H>5

.1.3

Prog

. ope

rato

r cod

e

Prog

. mac

hine

cod

eC

ode:

= . #

# +

####

Prog

. cod

. ges

tore

Cod

e:=

. ##

+##

##

6-di

git

num

ber

to id

entif

ygr

oups

of

vend

ing

mac

hine

s

Con

firm

?

Star

t

Init

ialis

e d

atab

ases

TEC

H>6

GSM

Cou

ntry Co

untry

Nam

e

Lang

uage

Lang

uage

Co

un

trie

s:Ita

lyG

erm

any

Gre

at B

ritai

nF

ranc

eS

pain

Lan

gu

ages

:Ita

lian

Ger

man

Eng

lish

Fre

nch

Spa

nish

TEC

H>5

.3EV

ADTS

TEC

H>5

.3.1

Pass

Cod

ePa

ss C

ode

Cod

e##

####

TEC

H>5

.3.2

Secu

rity

Cod

eSe

curit

y C

ode

Cod

e##

####

TEC

H>5

.3.3

Con

nect

ion

Wai

t ple

ase

© by NECTA VENDING SOLUTIONS SpA

56

Tec

hn

icia

n m

enu

- S

um

mar

y

0306 180-02

CO

NF

IRM

DA

TA

/C

ON

FIR

M F

UN

CT

ION

DE

LET

E D

AT

A/

EX

IT F

UN

CT

ION

PR

EV

IOU

S F

UN

CT

ION

/D

EC

RE

AS

E D

AT

A U

NIT

(-1

)N

EX

T F

UN

CT

ION

/IN

CR

EA

SE

DA

TA

UN

IT (

+1)

TEC

H>6

GSM

TEC

H >

6.1

PIN

TEC

H>6

.2G

SM p

re-a

larm

s

Pin

cod

e as

sign

ed t

o th

em

odem

Num

ber

of p

rodu

cts

afte

rw

hich

sen

d an

"en

ding

prod

uct"

pre

-ala

rm

TEC

H>6

.2.2

Res

et p

re-a

larm

cou

nt.

Res

ettin

g co

unt

of d

ispe

nsed

prod

ucts

Set t

hres

hold

s

TEC

H>6

.3Ba

nk N

umbe

r

TEC

H>1

Failu

res

TEC

H >

6.1

Pin

=##

####

TEC

H>6

.2.1

Set t

hres

hold

s

Res

et p

re-a

larm

cou

nt.

Lang

uage

Res

et p

re-a

larm

cou

nt.

Con

firm

?

TEC

H>6

.2.3

Thre

shol

d as

soci

atio

n

Ass

ocia

tion

of t

hres

hold

s to

5 se

lect

ions

and

2 t

rays

.

TEC

H>6

.3Ba

nk N

.

1 to

7 id

entif

ying

Sla

ve G

SM

0 id

entif

ying

Mas

ter

GS

M

Prod

uct n

ame

N. =

####

Prod

uct n

ame

Pre-

alar

mSe

lect

ion

##

#

##

Pre-

alar

m 1

Sele

ctio

n

Pre-

alar

m 6

Tray

##

#

© by NECTA VENDING SOLUTIONS SpA 0306 180-02

57

INITIALS DESCRIPTION

WIRING DIAGRAM LEGEND

INITIALS DESCRIPTION

CF FILTER CONDENSER

CM0-9 VENDING MOTOR CAM

D DIODE

EX EXECUTIVE COIN MECH CONNECTO

FA RADIO INTERFERENCE SUPPRESSO

FD PHOTODIODE

FT PHOTOTRANSISTOR

IP DOOR SWITCH

LCD LIQUID CRYSTAL DISPLAY

M1-... RELEASE MOTOR

MDB CONNECTOR FOR MDB COIN MECH

MUR COMPRESSOR

MVT FAN

NTC TEMPERATURE PROBE

RS232 SERIAL PORT

RT BALLAST

SOR OUT/R BOARD

SP PUSH-BUTTON BOARD

ST STARTER

SUC C.P.U. BOARD

TR TRANSFORMER

TX.... DELAYED FUSE (X=COURRENT)

NECTA VENDING SOLUTIONS SpA

sx36802

Snakky

NECTA VENDING SOLUTIONS SpA

Sx36901

Snakky

© by NECTA VENDING SOLUTIONS SpA NOTE

EDITION 03 06 CODE: H 180U 02

The Manufacturer reserves the right to modify, without prior notice, the characteristics of the equipment described in thispublication; and further declines to accept any responsibility for any inaccuracies contained in this publication which can beascribed to printing and/or transcription errors.All instructions, drawings, tables and information contained in this publication are confidential and can neither be repro-duced completely or in part, nor be transmitted to third parties without the written permit of the Manufacturer, who has thesole ownership.