Installation of network operating system based GUI (Graphical User Interface) and Text HOME

Installation of network operating system based GUI (Graphical User Interface)

and Text

HOME

COMPETENCE MAPING

2 3

Mendiagnosis permasalahan pengoperasian PC yang tersambung jaringangnosis

Melakukan perbaikan dan/ atau setting ulang koneksi jaringan

an

Melakukan instalasi sistem operasi jaringan berbasis GUI (Graphical User

Interface) dan Text

Melakukan instalasi perangkat jaringan berbasis luas (Wide Area

Network)

Mendiagnosis permasalahan perangkat yang tersambung jaringan berbasis luas

(Wide Area Network)

Membuat desain sistem keamanan jaringan

Mendiagnosis permasalahan pengoperasian PC dan

periferal

Melakukan perbaikan dan/ atau setting ulang sistem PC

Melakukan perbaikan periferal

Melakukan instalasi software

Melakukan perawatan PC

Melakukan instalasi sistem operasi berbasis graphical user interface (GUI)

dan command line interface (CLI)

Melakukan instalasi perangkat jaringan lokal (Local Area

Network)

Menerapkan teknik elektronika analog dan digital dasar

Menerapkan fungsi peripheral dan instalasi PC

Melakukan perbaikan dan/ atau setting ulang koneksi jaringan berbasis luas

(Wide Area Network)

Mengadministrasi server dalam jaringan

Merancang bangun dan menganalisa Wide Area

Network

Merancang web data base untuk content server

Lulus

Melakukan instalasi sistem operasi dasar

Menerapkan K 3 LH

Merakit Personal Komputer

Dasar Kejuruan Level I ( Kelas X ) Level II ( Kelas XI ) Level III ( Kelas XII )1

Melakukan instalasi sistem operasi jaringan berbasis GUI (Graphical User Interface) dan

Text

Klik Disini

HOME

Purpose

– Students can describe the software installation steps – Students can perform the installation of appropriate software

Installation Manual– Students can configure the network operating system – Student dapar to check the results using the installation

software (sampling) – Students can make troubleshooting .

Modul 12 Installation of network operating system

HOME

Before you install ubuntu, we must set the BIOS first. How to enter BIOS is we live press the "Del or F2" at the time of booting the computer to process first. You must do this quickly, because if the computer will not quickly go to the OS on the hard drive, but when you œlebih cepatâ € â € then the view will appear as follows:


After that we select the "Boot", then there will be display as follows:


After that we are setting the first boot on the CD-Room.

Then we select the "Boot Device Priority" then there will be display as follows:


After our first Boot settings on the CD-Room, we now save the configuration before we have to do with pressing F10.


After the BIOS configuration on our store, the display will appear on the screen as follows:

Then select "Start or Install Ubuntu" to start installing.


Once we select the "Start or Install Ubuntu" then there will be a display on the screen as follows:


Then we have to give the partition on the hard disk first, click on "System> Administration> Gnome Partition Editor." The appearance is as follows:


After that will appear on the screen display as follows:

When we want to create a new partition, right-click on the area of a black youth waiting ago to appear like the picture above.


After right-click on the area of the black image will appear as follows:

Click "Create" to start creating a partition.


Then the display will appear on the screen as follows:

Right-click on the area of a black youth, to appear above the image, and do not forget we have to determine how large a partition that will be used. Click add if you configure it.


After we add then click the blue color will appear in the area of black youth, in the picture above there are still areas of black youth, this is still due to the hard disk space remaining. Therefore, it is then right click again and select new.


In above picture free area will be use for swap partisi, then klik add, (linux minimal need swap partisi and root)


After that if we want do harddisk partition, then klik apply into aappear on the screen as follows :

Klik apply again, then wait Processes.


After Harddisk partition proceses finish, then appear on the screen as follows :

Then klik “Close”.


For Instalation we can klik INSTALL icon in the dekstop and wait proceses untik appear on the screen as follows:

In Picture above we ask for choose languange we use it, After choose klik foward


After click the forward view will appear as follows:

Here we will indicate where we are, because the show where we are, ubuntu system will set the time format GMT, when finished click forward


In the above picture of us in order to determine the type of keyboard we will use, once completed click forward.

After clicking on the forward view will appear as follows


When done click on the forward, then the display appears as follows:

Display is intended to fill our identity. Keep in mind, when filling the username letters must be used all small and can not have spaces, the same thing when we fill in the name of our computer.


Click the image forward into appear as follows:

This side there are two options of "erase the disk and edit the Manual." I erase the disk is to delete all the contents of hard drives, but this is quite dangerous if you have any data stored on the hard disk. Safe to select the manual edit partition. After that click forward.


After click forward, then the image will appear as follows:

Because we have made before the partition Click Fordward.


After klik forward, then the image will appear as follows :

Dari gambar di atas kita disuruh untuk menentukan “Mount Point” dari dua partisi yang telah kita buat tadi, buatlah seperti gambar di atas.setelah itu klik forward


After click forward, then the image will appear as follows:

This is a global configuration that we have created to install, click install (if the configuration is steady).


Click to install the image appear as follows:

If your computer shows like this, they are copying ubuntu system to your computer. The time needed to complete the loadingnya depending on the performance of the computer that you have. After that waiting to complete.


Once completed the display will appear as follows:

When you look at the computer screen looks like the above means that the installation of ubuntu on the computer you are finished.


• Insert the Ubuntu CD

• Restart the Computer and Display Repeat Installation akan appear


http://shots.osdir.com/slideshows/original.php?release=465&slide=1

• Select a location, language, keyboard settings during the installation process



• Specify the hostname to identify a computer on the network



• Select the appropriate resolution to the screen.



• Ubuntu Harddisk IDE check that will be used

• Hard drive will provide information to the label and the partition size

• Select the hard drive and then format to the installation process


• Enter your user name and user full Username will be used to enter the system linux



• To end the installation process enter a password and password confirmation



• Have time to install Ubuntu Linux IP using DHCP is used, how to change the following settings IP in Ubuntu still using DHCP to Static IP using the GUI.

• For Static IP settings, open the System - Administrator - Networking, then select the connection icon Wired


HOME

• Do click on the Property ago Wired connection settings window will appear for interface eth0, you do click on the drop-down box and select the Static IP address.


HOME

Documents

Installation of network operating system based GUI (Graphical User Interface) and Text HOME