Installation nstructions EuroClad - Selekta · The binding agent used is a thermosetting artificial resin with building authority approval for outdoor use. As a wood preservative,

Installation Instructions: EuroClad - Selekta

1

PSP Ltd exclusive distributors in NZ40226

V3 XX.3.18

www.euroclad.co

Auckland - Albany320 Rosedale RoadPh: 09 415 2800Fax: 09 415 2809Email: [email protected]

Auckland - East Tamaki60A Cryers RoadPh: 09 274 1800Fax: 09 271 2833Email: [email protected]

Hamilton13 Tawn Place, PuketePh: 07 850 6280Fax: 07 850 6284Email: [email protected]

Wellington61 Seaview Road, SeaviewPh: 04 568 7180Fax: 04 568 7183Email: [email protected]

Christchurch72 Hammersmith Drive, SockburnPh: 03 341 0248Fax: 03 341 0257Email: [email protected]

EuroClad Selekta (selekta façade profiles) are identical in terms of their core material and surface texture. However, they are available with different surface coatings.

The wood core consists of processed timber. We use exclusively untreated pulpwood in the form of wood shavings, thinning material and round timber from sustainable, domestic forestry. Imported timber is not used - especially from tropical climates.

The binding agent used is a thermosetting artificial resin with building authority approval for outdoor use.

As a wood preservative, we use an eco-friendly boron-based product with building authority approval that does not contain lindane or PCP.

This low flammability version is a mixture of boric acid and borax is used as a fire protection agent. No isocyanates, phosphates or halogens are added.

Several layers of paper are impregnated with artificial resins for use as a coating. The surface and core are fused together without seams in a single process under the application of pressure and heat.

ColorpanBase coating of paper impregnated with melamine resin, followed by coloured Colorpan surface coating using a pure, water-based acrylate. The pigments added are free of toxic heavy metals (no lead, chrome or cadmium).

Dekopan PlusMulti-layer coating, printed or dyed; transparent, weather- resistant surface coating of the decor side. Rear side brown, no colour options.

1) 4 mm particle board screw, using a hole of 3 mm diameter, 10 mm deep.2) Not available for all products, please ask for specific information.3) Maximum expected length change under extreme climate fluctuations.4) Gt 0A is the best, Gt 4A is the worst value.

5) With measurement geometry 0°/45°, standard illuminant “C”.(6) see Ignis AS 5113 advice 5347 I01 R 01 14 October 2017(7) see AWTA test report 7-586357-CQ AS 1530.3:1999 02 August 2012(8) see Facadelab test report no.17-17(9) see ASK reports for construction method – 6813R01V02_Euro.docx and 6813R02V02_Euro.docx

Product description – Ecology – Technical data

Technical data Values Unit Test specification

Fire Behaviour• Fire propagation testing and classification of external walls of buildings• Methods for fire tests on building materials, components and structures• Method of test for heat and smoke release rates for materials and products

using an oxygen consumption calorimeter• Fire test for construction of buildings in bushfire-prone areas

0 Flame Spread (6)

Fire Indices (7)

Group Number 3

BAL29 rating

N/A

AS 5113AS NZS 1530.3AS NZS 3837 – 1998

AS 3959

Fixing spacings for Cyclone rated areas Fixing Spacing N/A

AS NZS 1170.0:2002AS NZS 1170.1:2002AS 1720.1:2010AS 1684:2010

Water Penetration:Preliminary air pressure tests: ±1.5 kPaAS/NZS 4284 Static water test at 455 Pa• AS/NZS 4284 Cyclic water test, from 267-533, 355-711, 533-1066 Pa• E2/VM1 Series 1 water test at 455 Pa• E2/VM1 Series 2 water management test at 455 Pa• E2/VM1 Series 3 Wetwall test at 50 Pa• ULS test at ±2.5 kPa

NZ and AS result (8) N/AE2/VM1AS/NZS 4284:2008

CodeMark for New Zealand and AustraliaASNZ

N/ACertificate: CM40177 CM40226

Acoustic ratingsAS1191.2002 Acoustics - Method for Laboratory measurement of airborne sound transmission insulation of building elements AS/NZS ISO 717.1:2004 Acoustics – Rating of sound insulation in buildings and of building elements Part 1: Airborne sound insulations

Rw 49 and Rw 47 (9) N/AAS1191.2002AS/NZS ISO717.1:2004

Sustainability PEFC certified N/A PEFC

Density 800 – 950 kg/m3 EN 323


2


www.euroclad.co






V3 XX.3.18

General information, Profile dimensions, Calculating the required quantity & Guidelines

Scope

The scope of these installation instructions covers all installation variants of façade cladding, vertical, horizontal including soffits.

170

18

Coverage widths 155 +1

±1

-2

9

10

Wind side

d

d-e/5e/5

BA

d

Wind side e

Top view

View A(cladding side)

Technical data Values Unit Test specification

Flexural strength 40 – 45

N/mm2 EN 310

Elasticity modulus 4000 – 6000

N/mm2 EN 310

Tensile strength vertical to the surface 2.0 – 3.0

N/mm2 EN 319

Screw withdrawal strength (1) 800 – 1300 N

WERZALITTEST STANDARD

Swelling after storage after 2 h 0.3 – 0.6 % EN 317

in water at 20 °C after 24 h 3.0 – 5.0 % EN 317

Moisture content 5 – 10 % EN 322

Temperature resistance under permanent load under temporary load

-50 to +70+120

°C°C

WERZALITTEST STANDARD

Length change due to moisture/heat exposure (3)

1 – 3 mm/mWERZALITTEST STANDARD

Thermal conductivity λ 10 0.20 W/m·K DIN 52 612

Water vapour permeabilitydiffusion-equivalent air layer thickness 5 – 15 m DIN 52 615

Cross-cut test (4) GT 0A – GT 1A N/A EN ISO 2409

Scratch resistance 0.5 – 1.5 N EN 438

Light fastness Level 8 N/A DIN 54 004

Chemical resistance limited resistance N/A EN 438

Cigarette burn resistance not resistant to burns N/A as for EN 438

Colour deviation (5) Δ E < 1 N/A DIN 5033

Impact load impact resistant N/AWERZALITTEST STANDARD

1) 4 mm particle board screw, using a hole of 3 mm diameter, 10 mm deep.2) Not available for all products, please ask for specific information.3) Maximum expected length change under extreme climate fluctuations.4) Gt 0A is the best, Gt 4A is the worst value.

5) With measurement geometry 0°/45°, standard illuminant “C”.(6) see Ignis AS 5113 advice 5347 I01 R 01 14 October 2017(7) see AWTA test report 7-586357-CQ AS 1530.3:1999 02 August 2012(8) see Facadelab test report no.17-17(9) see ASK reports for construction method – 6813R01V02_Euro.docx and 6813R02V02_Euro.docx


3


V3 XX.3.18

www.euroclad.co






Sub-framework for façade cladding

Increased wind suction at the edge areas of the building walls must be considered when planning the sub-framework.

The fastening spacing of the EuroClad Selekta profiles must be reduced to max. 300 mm in these areas; additional support battens must be provided as necessary.

Calculating the required quantity (Calculation values exclude cutting waste)

Required quantity/m2 Required quantity/m2

Coverage width Standard lengths Façade profile Façade screw 3.5 x 50, stainless steel

EuroClad Selekta (Colorpan/Dekopan plus) at max. fastening spacing = 625 mm

(selekta) 155 mm 5400 mm 6.45 linear m 10.3 pcs.

Note: The wood decors are equivalent to natural wood surfaces, meaning that different grain textures are possible within a single shipment (plain and/or mottled). Unfortunately, sorting at the factory is not possible! In order to obtain a uniform overall finish, we recommend considering this fact and, for example, laying out the façade profiles before starting with the installation.

Maximum spacing of fasteners (mm)

N1 N2 N3 N4 C1 C2 C3General Corners General Corners General Corners General Corners General Corners General Corners General Corners

JD3 645 300 645 300 645 300 645 300 645 300 645 300 645 300JD4 645 300 645 300 645 300 645 300 645 300 645 300 645 300JD5 645 300 645 300 645 300 645 300 645 300 645 300 645 300J3 645 300 645 300 645 300 645 300 645 300 645 300 645 300J4 645 300 645 300 645 300 645 300 645 300 645 300 645 300

Wind loadings This is a simplified form or general rule of thumb for wind loadings. The product has been tested and results reported by Summermore Pty Ltd. to the requirements of:

• AS/NZ 1170.0• AS/NZ 1170.1• AS 1720.0• AS 1684

Wind Loading

Speed

Equivalent from Test data

Low <32m/s N1, N2

Medium 37m/s C1, N3

High 44m/s C2, N4

Very High 50m/s C2, N4

Extra High 55m/s C2, N4

Specific Design

>55m/s Engineered design

As wind zones in NZS 3604 are a simplif ied method of calculating wind action based on AS/NZS 1170.2, it is recommended that fixing testin g data is made readily available to suitably qual ified Engineers for Specific Design.

Testing data shows suitable fixing details for wind speeds up to 60m/s (C3), which is outs ide the scope of NZS 3604.

Seismic capacityProduct has also been certified by Summermore Pty Ltd. to meet and generally exceed the requirements of NZS 1170.5 (Earthquake Actions in New Zealand).

Important Building Design Notes:

• The supporting wall must be watertight and correct flashings used in the event of any water penetration i.e. severe storms

• There must be ventilation/drainage at the base of the wall

• Install breathable sarking over the stud frame keeping all overlaps pointing downwards and tape all joints

• Composite products expand and contract with temperature longitudinally – see installation instructions for joint options.


4


V3 XX.3.18

www.euroclad.co






Horizontal installation A Sub-framework

1. EuroClad Selekta profile.

2. Façade screw 6g x 50, stainless steel.

3. Cavibat batten system 45 x 18 mm, @ spacing max. 625 mm. Dependent on wind loads.

4. Fastening with 2 screws 6g x 50 mm, stainless steel batten to wall frame or equivalent.

B Starter details


2. Fastening with 2 screws 6g x 50 mm, stainless steel batten to wall frame or equivalent.

3. Cavibat batten system 45 x 18 mm, @ spacing max. 625 mm. Dependent on wind loads.

4. Horizontal staerter profile.

C Window details


2. Horizontal starter profile.

3. Window frame flashing.

4. Window frame.

5. Z profile.

max. 625

10 1

55 m

m

A Typical fixing detail

B Horizontal section C Vertical section

3

2

1

21

2

1

4

EuroClad Selekta pro�le

20mm cavity

Interior lining

Bottom plate w/DPC under

15mm drip min.

6g x 50mm SS screw

Cavibat - 45x18mm

Foundation / �oor

Horizontal Starter Pro�le

5mm dia. holes @ 15mm Crs.PVC cavity closure �ashing w/

Wallframing

Wall Sarking

150mm min.225mm min.

Top of Unpaved.

Paving

1

2

3

4

5


20mm cavity

Interior lining

6g x 50mm SS screw

Cavibat - 45x18mm

Wallframing

Wall Sarking

Z-pro�le

Window Frame

20mm cavity

Window frame


6g x 50 mm SS screw

Wall sarking

Interior lining Cavibat - 45x18mm

20mm cavity

Horizontal starter pro�le

Window frame �ashing(Z-pro�le)Timber

sill

Wall

Lintel

1

4

5

1

2

3

Ventilation opening (continuous)5

4


20mm cavity

Interior lining

6g x 50mm SS screw

Cavibat - 45x18mm

Wallframing

Wall Sarking

Z-pro�le

Window Frame

20mm cavity

Window frame


6g x 50 mm SS screw

Wall sarking


20mm cavity



sill

Wall

Lintel

1

4

5

1

2

3


4

Typical fixing detailA

Starter detailsB

Window detailsC

Please note:

• In New Zealand cavity battens are considered non-structural and form a packer only.

• Horizontal installation can be done where the building can be designed to AS/NZS 4284


5


V3 XX.3.18

www.euroclad.co






10

10

D Internal corner

X

max.100

X

max.100

X

A Fastening spacing B Sub-framework, alternative

231

4

2

11

1

max. 20

C Start of installation, alternative

34

1

5

1

2

3

Horizontal installation

A Fastening spacing

1. EuroClad Selekta profile

2. Façade screw 6g x 50, stainless steel

3. Elongate fixing hole

4. Cavibat 45 x 18 mm

X = 3 or more supports, max. 625 mm

X = for only 2 supports, max. 300 mm;

Profile excess length max. 100 mm

Fastening materials

Use only screws 6g x 50, stainless steel.

Always centre the screws in the punched fastening holes of the façade profile.

B Sub-framework alternative

e. g. block work or concrete

1. Building wall

2. Support batten – ferrule, top hat

3. Elongated fixing hole

Alternatively, other sub-framework systems can also be used.

C Start of installation from below


2. Horizontal starter profile

3. 20 mm cavity

4. Ventilation profile, galvanised steel

5. Wall sarking


7. 6g x 50 stainless steel screw

D Internal corner


2. 6g x 50 stainless steel screws

3. Aluminium internal corner trim

4. 75 x 75 mm Dynaflash plate

5. Wall sarking



20mm cavity

Interior lining

Bottom plate w/DPC under

6g x 50mm SS screw

Cavibat - 45x18mm

Wallframing

Wall Sarking

Wallframing

1

5

3

6

7

Horizontal starter pro�le2

Galvanised vent pro�le

4

Interior lining

Concretetilt slab

6g x 30mm SS screw5


Galvanised vent pro�le3


40 x 40 mm batten

Wall Sarking

1

Drive pin6

4

Fastening spacingA Sub-framework, alternativeB

Start of installation, alternativeC

Fastening to masonry wallE

10

10

D Internal corner

X

max.100

X

max.100

X


231

4

2

11

1

max. 20

C Start of installation, alternative

34

1

5

1

2

3


Watergate building paper continuous around corner

Aluminium internalcorner trim

6gx50mmSS screw

75x75mm DynaFlash

6g x 50mm S/S drill screws through batten into stud

Note: Double solid timber 75x45mm studs required at internal corners

Interior lining

1

Cavibat

Cavibat

6

6

5

2

4

3

2

Internal corner D

Please note:

• Baseboard termination At least 100 mm spacing to the floor.

• Avoid designs that allow moisture build-up.


E Masonry wall fastening



3. Ventilation profile

4. 40 x 40 mm batten

5. 6g x 30 mm stainless steel screw

6. Drive pin


6


V3 XX.3.18

www.euroclad.co







A External corner



3. Aluminium internal corner profile

4. Aluminium external corner profile



20mm cavity

Interior lining

6g x 50 mm SS screw

Cavibat - 45 x 18mmWallframing

Wall Sarking

CavibatConnectionpro�le FInterior

lining

Wallframing

Wall Sarking

6g x 50 mm SS screw


20mm cavity

1

2

3

4

Ventilation pro�le

5

6

7

Connection to pitched roof and soffitC

B External corner Alternative



3. Aluminium external Y profile



C Roof connection


2. 6g x 50 stainless steel screw


4. wall sarking



7. Connection profile F

External CornerA

Interiorlining

Solid timber 90x45mm wall frame

Aluminium internal corner trim

Aluminium external corner trim



75x75mm DynaFlash

Cavibat

Cavibat

1

2

3

4

5

6

External Corner alternativeB

Cavibat

Cavibat

Interiorlining


Aluminium

Mitred edge

external Y pro�le


6g x 50 mm SS screw


75x75mm DynaFlash

1

2

5

3

4

Please note:

• The Aluminium External/Internal corner profile can be used in reverse for Internal corner applications.



7


V3 XX.3.18

www.euroclad.co







A Window lintel and sill connection



3. Z profile

4. Window frame

5. Ventilation opening, continuous


Window sill connection


2. Window frame

3. Z profile

B Window reveal connection


2. 2 piece edge cover 40/25


4. Window frame

C Window reveal alternative connection


2. Jamb flashing profiles


4. Window frame

Window lintel and sill connectionA

EuroClad Selekta pro�leHorizontal installation

Watergate building paper

Solid timber double studs behind vertical jointer 90x45mm

Interior lining

2 piece edge cover 40/25

Windowframe

Cavibat

12

4

3

EuroClad Selekta pro�leHorzontal installation


Solid timberdouble studs behind

vertical jointer 90 x 45mm

Interior lining

Continuoussealant

Windowframe

Cavibat

1

4

3

2Jamb �ashing pro�le

Window horizontalB Window reveal alternative connectionC


20mm cavity

Interior lining

6g x 50mm SS screw

Cavibat - 45x18mm

Wallframing

Wall Sarking

Z-pro�le

Window Frame

20mm cavity

Window frame


6g x 50 mm SS screw

Wall sarking


20mm cavity



sill

Wall

Lintel

1

4

5

1

2

3


4

Please note:

• At the transition between the reveal and the lintel, the connection profiles are given a mitre cut.

• The Z profile covers the vertical left and right hand side flashing profiles.

Please note:



20mm cavity

Interior lining

6g x 50mm SS screw

Cavibat - 45x18mm

Wallframing

Wall Sarking

Z-pro�le

Window Frame

20mm cavity

Window frame


6g x 50 mm SS screw

Wall sarking


20mm cavity



sill

Wall

Lintel

1

4

5

1

2

3


4


8


V3 XX.3.18

www.euroclad.co






Horizontal Installation only for EuroClad Selekta

A Door head detail





5. Z–profile

B Parapet detail 1


2. Edge trim

3. Parapet flashing


C Parapet detail 2


2. Edge trim

3. Parapet flashing


D Horizontal to vertical profile


2. Support batten

3. Connection cover profile

4. Pan head screw 4 x 40, stainless steel into flashings or profiles

Interior lining 20mm cavity


Timber Head

Door Frame


Wall Sarking

Lintel

Wall

6g x 50 mm SS screw

Cavibat

Door Trim

Door

Ventilation-pro�leZ-pro�le

1

2

3

4

5

6EuroClad Selekta pro�lehorizontal installation

Solid timber wall

Parapet Flashing

Cavibat

Sarking

Packer

Edge Trim

EuroClad Selekta pro�lehorizontal installation

1

4

1

2

3


Solid timber wall

Parapet Flashing

Cavibat

Sarking

Packer

Edge Trim


1

4

1

2

3

H3 timber 45 x 20mm cavity battens

Pan head screw4 x 40mm stainless steel

1

3

EuroClad Selekta profilevertical installation

Conncetion cover profile

75x75mm DynaFlash

Sarking


Solid timber cavity batten with 5º slope on top edge

Interior lining

2

Door head detailA Parapet detail 1B

Parapet detail 2C Horizontal to vertical profileD

Tip:

Peg a 20 mm wide batten to the sub-framework at the joint location. Position the façade profiles flush on both sides. After installation of the façade profiles, remove the batten and fix, then push cam home.

Please note:



9


V3 XX.3.18

www.euroclad.co






10 155 mm

A Sub-framework


5

6

2

1

21

3

3

2

1

600 - 625

max

. 62

53

4

Vertical installation only for EuroClad Selekta

A Sub-framework


2. Façade screw 6g x 50, stainless steel

3. Timber batten 20 mm x 40 mm, spacing max. 625 mm

4. Fastening with 2 screws 4 x 50 mm, stainless steel

5. Timber frame construction or counter batten at least 45 mm x 75 mm, or at least 20 mm higher than second layer of thermal insulation. (See also note for B – C, no. 2)

6. Dowel and screw with building authority approval

Note:

Optional ventilation detail must conform to local sectional penetration table.

B - C Sections


2. Back ventilation spacing (at least 20 mm*)

3. Timber batten 20 x 40 mm spacing max 625 mm.

Sub-frameworkA

10 155 mm

A Sub-framework


5

6

2

1

21

3

3

2

1

600 - 625

max

. 62

53

4

Horizontal sectionB Vertical sectionC

Please note:

• Ventilation penetration holes as per section allowance table.

• Otherewise a secondary batten is required.


10


V3 XX.3.18

www.euroclad.co






max.100

X

max.100

X

X


3

4

2

mind. 20 mm

10

E Internal corner, alternative

C Start of installation D Connection to pitched roof

23

1

1

4

2

3

4

12

4

1

at least

1

1

2

3


A Fastening spacing


2. Façade screw 6g x 50mm, stainless steel

3. Elongated fixing holes

4. Timber batten 20 mm x 40 mm

X = 3 or more supports, max. 625 mm

X = For only 2 supports, max. 300 mm; profile excess length max. 100 mm

Fastening materials

Use only screws 6g x 50mm, stainless steel. Always centre the screws in the fastening holes of the façade profile.

B Sub-frameworks – alternatives

1. Building wall

2. Support batten – ferrule, top hat

3. Masonary fixing screw

Alternatively, other sub-framework systems can also be used.

C Start of installation from below


2. Ventilation profile, galvanised steel

3. Ventilation opening, continuous

D Alternative detail


2. Vertical starter profile

E Joiner detail


2. Connection cover profile 2 piece

3. Pan head screw 4 x 40 mm stainless steel

4. Edge trim profile

Fastening spacingA Sub-framework, alternativeB

EuroClad Selekta profile


20mm cavity

Bottom plate - 90x45mm solid timber

PVC cavity closure flashing

15mm drip min. or vertical starter profile

Ventilation opening, continuous

Interior lining

Solid timber cavity battenwith 5º slope on top edge

Foundation / floor

Wall framing90x45mmsolid timber

1

3

Ventilation profileglavanised steel

2


6g x 50mm SS screw

with bottom edge mitre cut @ 10º max

Wall Sarking

Batten

20mm cavity

Wall

Vertical starter-pro�le

Wall Wrap

2

1

Foundation / floor

max.100

X

max.100

X

X


3

4

2

mind. 20 mm

10

E Internal corner, alternative

C Start of installation D Connection to pitched roof

23

1

1

4

2

3

4

12

4

1

at least

1

1

2

3

Starter detailC Alternative detailD

Solid timberbatten

EuroClad Selekta pro�leVertical installation

EuroClad Selekta pro�leVertical installation

Connection cover pro�le

75x75mm DynaFlash

Pan head screw 4 x 40mm, stainless steel

Watergatebuilding paper


Interior lining

EdgeTrim

12

34

1

Lorem ipsum

Joiner detailE


11


V3 XX.3.18

www.euroclad.co







A External corner


2. External corner (two-part), aluminium

3. Internal corner (two-part), aluminium

4. 75 x 75 mm Dynaflash

B Internal corner


2. Internal corner (two-part), aluminium

3. 75 x 75 mm Dynaflash

4. 6g x 50 mm Stainless steel screw

C Masonry wall


2. 40 x 40 mm timber batten

3. Drive pin

4. 6g x 30 mm Stainless steel screw

External corner, alternativeA

EuroClad Selekta pro�leWatergate building paper continuous around corner

Solid timber batten

Solid timber batten

Aluminium internalcorner trim

6g x 50mm SS screw

75x75mm DynaFlash

6g x 60mm S/S drill screws through batten into stud

Note: Double solid timber 75x45mm studs required at internal corners

Interior lining

1

4

2

3

4

Internal cornerB

75x75mm Dyna�ash

Interiorlining


Aluminium internal corner trim

Aluminium external corner trim

Euro Clad Selekta pro�le

6g x 50mm SS screw


Solid timber batten

Solid timber batten

2

3

1

4

Please note:

• The Aluminium External/Internal corner profile can be used in reverse for Internal corner applications.

Interior lining

Concretetilt slab

6g x 30mm SS screw4

40 x 40 mm batten

EuroClad Selekta pro�le1

Wall Sarking5

Drive pin3

2

Fastening to masonry wallC


12


V3 XX.3.18

www.euroclad.co







A & B Window lintel connection


2. Vertical starter profile

3. Z profile, aluminium

C Door head connection


2. Ventilation profile, continuous

3. Z profile, aluminium

D Window reveal connection


2. 2 piece edge cover 40/25

3. External corner profile, aluminium


Interior lining

6gx50mm SS screwWallframing

Wall Sarking

Z-pro�le

Window Frame

Window Frame


6gx50mm SS screw

Wall Sarking

Interior lining

Batten

20mm cavity

Window Frame FlashingTimber Sill

Wall

Lintel

Vertical starter-pro�le

Wall Wrap

20mm cavity

Batten

20mm cavity

1

3

2

1

Window lintel connectionA Window reveal connectionB

EuroCladSelekta pro�le

20mm cavity

Interior lining

6gx50mm SS screw

Batten

Wallframing

Wall Sarking

Z-pro�le

Window Frame

B69450

Window Frame


Wall Sarking

Interior lining

20mm cavity

Vertical starter pro�le

Z-pro�le

Timber Sill

Wall

Lintel 6gx50mm SS screw

Batten

1

1

2

3

3

Timber Head

Wall

Lintel

Door Frame


Wall Sarking

Interior lining 20mm cavity

Vertical starter pro�le

Z-pro�leVentilation pro�le

6gx50mm SS screwBatten

Door Trim

Door

1

2

3

Door head connectionC

EuroClad Selekta pro�levertical installation



Interior lining

2 piece edge cover 40/25Cavity

batten

1 2

Window reveal connectionD

Please note:

• At the transition between the reveal and the lintel, the connection profiles are given a mitre cut.

• Ensure ventilation profile is underneath Z profile


13


V3 XX.3.18

www.euroclad.co






10

10

10

10

25

25

LA

X =

max

. 625

X =

max

. 625

a

600 - 625

E Vertical / horizontal installation F Continuous vertical butt joint

C Vertical / horizontal installation D Continuous horizontal butt joint

A Vertical installation B Continuous horizontal butt joint

G Diagonal installation

1

1

1

1

2

2

2 3

1

2

3

1

4

1

5

4

3

2

2

1

3

4

4

2

3

2 45

3 11

5 11

6

3

5

2

7

1

8

9

4

10

10

10

10

25

25

LA

X =

max

. 625

X =

max

. 625

a

600 - 625





1

1

1

1

2

2

2 3

1

2

3

1

4

1

5

4

3

2

2

1

3

4

4

2

3

2 45

3 11

5 11

6

3

5

2

7

1

8

9

4

10

10

10

10

25

25

LA

X =

max

. 625

X =

max

. 625

a

600 - 625





1

1

1

1

2

2

2 3

1

2

3

1

4

1

5

4

3

2

2

1

3

4

4

2

3

2 45

3 11

5 11

6

3

5

2

7

1

8

9

4

A & B Vertical installation, continuous


2. Install 2 support battens 20 x 40 mm in each joint area

3. 10 mm expansion gap

C & D Vertical / horizontal installation, continuous horizontal butt joint

The sub-framework must be modified at the butt joint according to the installation direction.


2. Support battens 20 x 40 mm

3. Z profile, maintain 10 mm gap at top and bottom

4. Back ventilation spacing at least 20 mm


E Vertical / horizontal installation, continuous vertical butt joint



3. Pan head screw 4 x 40, stainless steel

Fibre-Cement/Alum/Mini-OrbCladdinginstallation

Euro Clad Selekta pro�levertical installation

DynaFlash

Sarking building paper

Timber Stud Wall

Interior lining

Timber cavitybatten

Timber cavitybatten

Z pro�le

1

Vertical junctionBVertical installationA

Vertical/horizontal installationC Vertical/horizontal installationD

H3 timber 45 x 20mm cavity battens

Pan head screw4 x 40mm stainless steel

1

3

EuroClad Selekta profilevertical installation

Conncetion cover profile

75x75mm DynaFlash

Sarking



Interior lining

2

Joiner detailENote: Position the vertical support battens at the transition point at least 25 mm above the horizontal counter batten to ensure back ventilation.

Tip: Peg a 25 mm wide batten to the sub-framework at the joint location. Position the façade profiles flush on both sides. After installation of the façade profiles, remove the batten and screw on the cover profile T + G in its place.

Support batten spacing = BS

Refer to Wind loading table on page 3.


14


V3 XX.3.18

www.euroclad.co






20mm cavity

Interior lining

6g x 50mm SS screw

Cavibat - 45x18mmWallframing

Wall Sarking

20mm cavity

Interior lining

Wallframing

Wall Sarking

Cavibat - 45x18mm

EuroClad Selekta pro�le (vertical)1


Connection pro�le F

Ventilation pro�le3

4

Roof and soffit detail – verticalB

A Parapet detail


2. Edge trim

3. Parapet flashing


B Roof and soffit detail – vertical




4. Connection profile F

C Horiontal pipe detail



3. Pipe flashing (min 100 mm outside pipe)

4. Flashing tape

5. Sealant over backing rod

6. Protective pipe flange

D Vertical pipe detail



3. Pipe flashing (min 100 mm outside pipe)

4. Flashing tape

5. Sealant over backing rod

6. Protective pipe flange

Pipe to have min. 5º fall to outside

Square of flexible flashing tape to a min. of 100 mm outside of pipe. Ensure seal with pipe bandage

PVC protective flange

Sealant over backing rod

20mmØ pipe


Building underlay carefully cut to suit pipe

EuroClad Selekta profile over flashing tape, carefully cut to suit pipe. Seal with PVC flange and flexible sealant

Flexible flashing tape bandage min. 25mm wide all round pipe

1

2

3

4

5

Pipe to have min. 5º fall to outside

Square of flexible flashing tape to a min. of 100 mm outside of pipe. Ensure seal with pipe bandage

PVC protective flange

Sealant over backing rod

20mmØ pipe

Cavibat40x18 mm

Building underlay carefully cut to suit pipe

EuroClad Selekta profile over flashing tape, carefully cut to suit pipe. Seal with PVC flange and flexible sealant

Flexible flashing tape bandage min. 25mm wide all round pipe

1

3

2

4

5

6


Solid timber wall

Parapet Flashing

Cavibat

Sarking

Packer

Edge Trim


1

4

1

2

3

Parapet detailA

Horiontal pipe detailC Vertical pipe detailD


15


V3 XX.3.18

www.euroclad.co






General guidelines

Arguments for a back-ventilated curtain cladding of the exterior wall

• Energy savings• Weather protection• Attractive design• Increased building value

Handling

The EuroClad Selekta façade profiles must be stored in their packaging, lying flat and dry until use.

Sawing with power tools

Hard metal saw blade, high number of teeth, (tooth pitch approx. 10 – 15 mm), saw blade with alternate top bevel or hollow-tooth flat-top teeth.

Sawing with hand saws

A well-sharpened and dressed saw with small teeth is sufficient.

Fastening the façade profiles

Façade fixed-width 6g x 50, stainless steel screws. Centre the fastening screws through the existing punched holes. The screws may only be screwed in until the screw head rests against the surface.

Fastening of all connection profiles

Fix EuroClad Selekta with 6g x 50, stainless steel screws.

Expansion

The length change of the façade profiles is approx.

1 – 3 mm/linear m, depending on moisture and temperature. Expansion joints of 10 mm must be maintained at profile butt joints and profile connections wherever possible.

Sealing cut edges

Cut edges must be sealed free of pores with Werzalit edge sealant.

Cleaning

Clean only with water and a liquid detergent. Never use an abrasive cleaner.

Sub-framework

Façade profiles are typically fastened to a wood or steel hat sub-framework. In principle, the following guidelines should be followed for wood sub-frameworks:

a) The sub-framework must be fastened using screws with building authority approval and in accordance with the instructions of the manufacturer.

b) The sub-framework must be level and plumb.

c) All Structural framework must be in accordance to New Zealand Building Standards & Local Building Codes.

Thermal insulation

The thermal insulation material must be fastened with appropriate hardware, such as insulation tape, in accordance national building codes.

Back ventilation

The back ventilation spacing must be at least 20 mm.

The back ventilation cross-section may not be regularly diminished by battens or other objects. The ventilation inlets and outlets must have consistent widths of at least 20 mm.

Profile surface finishes

Colorpan: Single-colour coating based on an acrylic paint system.

Dekopan Plus: Wood decor with transparent acrylic coating. When stored in damp conditions (e.g. kept outdoors, wrapped in film packaging), the paint layer might undergo partial changes, givin it a milky appearance. These disappear completely once the profiles have dried. The resistance of the paint system is not affected. The environmentally-friendly acrylic coating is finally cured by the effects of weathering.

Connections

Clearance at least 10mm.

If you have additional questions, please contact PSP Limited. Subject to changes due to technical improvements.

Please note: Heavy structures, such as an awning, climbing trellis, etc., may not be fastened directly to the cladding or its sub-framework. Provide separate sub-frameworks.


16


V3 XX.3.18

www.euroclad.co






Fire installation guidelines for commercial applicationsTo verify the installation of the EuroClad Selekta panel a number of reviews relating to the location, fixing, nature of the wall and proximity to exposures being either an external fire or a fire source feature the following considerations need to be applied:

Guide for performance-based acceptance*:

# Requirement Measure Measure of Acceptance

1 Insulation Non-Combusti ble • The insulation must be non-combustible

2 Sarking type material Flammability <_5 • The sarking type material is to be non-combustible or have a flammability index not exceeding 5.

3 Fixing Mechanical • The fixing must be mechankal onto top hats at spacings no more than 600mm centres

4 Return wall Single plane • The EuroClad Selekta panel is to be installed on a single plane only and not on a re-entrant return wall at 90º or less to the primary Selekta clad wall.

5 Non-Sprinklered Building Spandrel protection to the wall frame.

• A non-sprinklered class 2-9 building must have spandrels protecting the wall frame (i.e. from both sides of the frame} In accodance with clause C2.6 of the BCA.

6 External fire spread from fire source feature

External fire source feature to be greater than 1.8-m from the EuroClad Selekta panel installation

• The panel is to be installed greater than 1.8m from an external fire source feature.

7 Wall FRL requirement The wall FRL to be independent of the EuroClad Selekta Panel and to protect the wall frame from both directions

• The FRL of the wall is to be achieved independent of the and EuroClad Selekta panel.

8 Exposure to direct flame testing of the EuroClad Selekta impact. This includes unprotected openings, external balconies/platforms or the ground level.

Testing of the EuroClad Selekta Panel to AS 5113:20016

• The testing of the EuroClad Selekta Panel to AS 5113:20016, being a large scale external wall test, has demonstrated fire spread does not occur along a single plane

9 Above or near an exit Spread of fire and limited debris • The testing of the EuroClad Selekta panel insulation to AS 5113:20016, being a large scale external wall test, has demonstrated that vertical and horizontal fire spread, outside of the fire istself, on a single plane does not spread. The debris from panel included small elements less than 2kg in weight which did not individually flame for more than 20 seconds at a time. Outside of the fire event itself, EuroClad Selekta debris is unlikely to cause an exit to be blocked.

* Refer to AS 5113; AS NZS 1530.3; AS NZS 3837 – 1998; AS 3959 and certification advice prior to submission to your local authority.

Documents

Installation nstructions EuroClad - Selekta · The binding agent used is a thermosetting artificial resin with building authority approval for outdoor use. As a wood preservative,