Upload
christiaan-nijkamp
View
296
Download
7
Tags:
Embed Size (px)
Citation preview
Allgon Microwave Radio
Installation Manual
IMPORTANT NOTICEIMPORTANT NOTICEIMPORTANT NOTICEIMPORTANT NOTICE
This document is subject to revision without notice.This document is subject to revision without notice.This document is subject to revision without notice.This document is subject to revision without notice.
Allgon Microwave AB have no liability for typing errors in this Allgon Microwave AB have no liability for typing errors in this Allgon Microwave AB have no liability for typing errors in this Allgon Microwave AB have no liability for typing errors in this document or damages of any kind that result from the use of document or damages of any kind that result from the use of document or damages of any kind that result from the use of document or damages of any kind that result from the use of this document.this document.this document.this document.
Read this manual carefully before installing the Allgon Read this manual carefully before installing the Allgon Read this manual carefully before installing the Allgon Read this manual carefully before installing the Allgon Microwave Radio equipment and follow any and all instructions Microwave Radio equipment and follow any and all instructions Microwave Radio equipment and follow any and all instructions Microwave Radio equipment and follow any and all instructions set forth herein. Non-compliance with, or non-observance to set forth herein. Non-compliance with, or non-observance to set forth herein. Non-compliance with, or non-observance to set forth herein. Non-compliance with, or non-observance to the instructions set forth in this manual may cause personal the instructions set forth in this manual may cause personal the instructions set forth in this manual may cause personal the instructions set forth in this manual may cause personal injury or damage to property and may be illegal. Allgon injury or damage to property and may be illegal. Allgon injury or damage to property and may be illegal. Allgon injury or damage to property and may be illegal. Allgon Microwave AB and its subsidiaries disclaim any and all liability Microwave AB and its subsidiaries disclaim any and all liability Microwave AB and its subsidiaries disclaim any and all liability Microwave AB and its subsidiaries disclaim any and all liability in case of non-compliance with, or non-observance to the in case of non-compliance with, or non-observance to the in case of non-compliance with, or non-observance to the in case of non-compliance with, or non-observance to the instructions set forth in this manual.instructions set forth in this manual.instructions set forth in this manual.instructions set forth in this manual.
Allgon is a registered trademark. All other brand and product Allgon is a registered trademark. All other brand and product Allgon is a registered trademark. All other brand and product Allgon is a registered trademark. All other brand and product names that appear in this manual are trademarks or registered names that appear in this manual are trademarks or registered names that appear in this manual are trademarks or registered names that appear in this manual are trademarks or registered trademarks owned by the respective companies or trademarks owned by the respective companies or trademarks owned by the respective companies or trademarks owned by the respective companies or organisations. organisations. organisations. organisations.
© Allgon Microwave AB 2001 – All Rights Reserved© Allgon Microwave AB 2001 – All Rights Reserved© Allgon Microwave AB 2001 – All Rights Reserved© Allgon Microwave AB 2001 – All Rights Reserved
Product Number: WLDM001EnCProduct Number: WLDM001EnCProduct Number: WLDM001EnCProduct Number: WLDM001EnC
Installation ManualContents
WLDM
ContentsChapter 1: Introduction 5
Applicable Documents 5Document Information 6Typing Conventions 7
Chapter 2: Site Requirements 8Safety Requirements 8Indoor Requirements 11Outdoor Requirements 15
Chapter 3: Indoor Installation 18Tools Required for Indoor Installation 18Indoor Equipment 19Indoor Accessories 20Baseband Unit 22Traffic Interface Unit 24Mounting the Indoor Unit 28Installing the Cables for the Indoor Unit 33
Chapter 4: Outdoor Installation 41Tools Required for Outdoor Installation 41Outdoor Equipment 42Choosing Vertical or Horizontal Polarization 44Mounting the RF Unit on the Antenna Unit 46Choosing Left or Right Side Antenna Mounting 48Fastening the Mast Mounting Bracket 49Mounting the Antenna/RF Unit on the Mast
Mounting Bracket 51Grounding the Antenna/RF Unit 52Outdoor Radio Cable Installation 52
001EnC
Installation ManualInstallation ManualInstallation ManualInstallation ManualContentsContentsContentsContents
Chapter 5: Start-up and Configuration 55Equipment Required for Configuration 57Status LEDs 60Start-up and Shut-down 61Local Management Connection 63Accessing the Radio Terminal Web Pages 78Initial Radio Terminal Configuration 79Remote Management Connection 90Interterminal Connection 100
Chapter 6: Antenna Alignment 103Tools Required for Antenna Alignment 103Preparations 103Alignment Procedure 103
Chapter 7: Installation Verification and Test 106Checking RF Channel Status 106
Chapter 8: Maintenance 108Replacing the Baseband Unit 108
Chapter 9: 1+1 Installation and Configuration 1121+1 Installation Indoor Equipment 1121+1 Installation Outdoor Equipment 113Polarization in Separately Mounted Installations 115Installing a Separately Mounted 1+1 Installation 116Redundancy Configuration 118Traffic Channels in a 1+1 Configuration 120
Index 121
WLDM001EnC
Installation ManualChapter 1: Introduction
WLD
Chapter 1: Introduction
Applicable Documents
WLDM001 Installation ManualThis manual describes the installation of the Allgon Microwave Radio including start-up and configuration.
WLDM002 Operation and Maintenance ManualThis manual describes how to use a web browser interface to manage the Allgon Microwave Radio. It also contains instructions for troubleshooting and maintenance.
WLDM003 Technical DescriptionThis document contains a detailed technical description of the Allgon Microwave Radio product range.
WLDM004 Product ListThis document lists all equipment and accessories for the Allgon Microwave Radio.
M001EnC 5
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 1: Introduction
6
Document Information
This manual and all documents listed above cover the complete Allgon Microwave Radio product range:
• Baseband Unit (WAABxxx/yy)
• Traffic Interface Unit (WAADxxxyyy/zz)
• Radio Frequency Unit (WAAAxxxyy/zz)
• Antenna Unit (WAAF001xxxyy/zz)
• Accessories (WMxxyyy/zz).
The letters x, y and z in the product numbers listed above are variables that depend on the product variant. For further details concerning product numbers, refer to the respective section in this manual or contact your sales office.
WLDM001EnC
Installation ManualChapter 1: Introduction
WLD
Typing Conventions
The following typing conventions are used in this manual:
Select Prompts the user to perform a selection on the screen by clicking on an active object.
Enter Prompts the user to type text using the keyboard.
Press Prompts the user to press a button on the keyboard.
Check Prompts the user to click in a check box to activate an option.
command Prompts the user to enter the command command.
<variable> Prompts the user to enter a value for the variable <variable>.
[<variable>] The user may enter a value for the variable <variable> but is not required to.
<variable1>|<variable2>
The user may enter a value for either the variable <variable1> or the variable <variable2>.
response Text displayed in response to an executed command.
Request Prompts the user to perform a specific action or enter a specific value.
‰ Indicates the start of a workflow.
M001EnC 7
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 2: Site Requirements
8
Chapter 2: Site Requirements
Safety Requirements
Terminology
This manual contains two kinds of safety warnings which represent different degrees of danger:
Safety Precautions
• Access to the Allgon Microwave Radio shall be restricted to service personnel.
• Observe the safety warnings and take all precautions listed in this manual.
CAUTION!
This warning is used for dangers which could cause injuries to personnel or damage to the equipment if ignored.
DANGER!
This warning is used for dangers which could cause life-threatening injuries to personnel or destroy the equipment if ignored.
WLDM001EnC
Installation ManualChapter 2: Site Requirements
WLD
• Follow the installation procedures in this manual and use the correct tools, preferably the recommended tools, for tightening of nuts etc.
• Do not use any components (screws, nuts etc.) other than those delivered together with the Allgon Microwave Radio equipment or recommended by Allgon AB.
• Use the necessary safety devices (helmet, safety line etc.) when working on, or around the mast. Be aware of the risk of falling objects. Secure the joined Antenna/Radio Frequency Unit before lifting it up the mast.
Beryllium Oxide
Some components in the Radio Frequency Unit contain beryllium oxide (BeO) which is poisonous if inhaled as dust or smoke. This can only happen if these components are damaged in some way. The product is completely safe as long as the components are not damaged.
Warning signs indicate parts containing beryllium oxide.
DANGER!
Do not file, grind, machine or apply acid to parts containing beryllium oxide!
Berylliumoxide
hazard
M001EnC 9
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 2: Site Requirements
10
Voltage Hazards
Grounding
It is recommended to ground all equipment before the power cable is connected.
Electrical Safety
The Allgon Microwave Radio equipment meets the electrical safety requirements in EN 60950.
DANGER!
All safety precautions must be carried out! Contact with power lines can be lethal! Even voltages below 60 V can be dangerous!
CAUTION!
All indoor and outdoor grounding systems on the installation site must meet the requirements of the applicable national standards!
WLDM001EnC
Installation ManualChapter 2: Site Requirements
WLD
Indoor Requirements
Indoor Space Requirements
Table 1 Space requirements for the Indoor Unit
All interfaces are accessible on the front of the Indoor Unit.
Installation W H D F1
1. Space required for connecting cables and connectors.
Single Indoor Unit 19" 1U 278 mm 70 mm2U Magazine 19" 2U 2902 mm
2. The units will extend an additional 20 mm in front of the rack, compared to Single Indoor Unit mounting.
70 mm
6U Magazine 19" 6U 2902 mm 70 mm
M001EnC 11
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 2: Site Requirements
12
Indoor Power Requirements
Power Supply
The power supply should be a two wire power distribution with a nominal voltage between 24 V and 60 V DC, any polarity.
Internal Protection Circuits
The radio terminal is equipped with two 5 A fuses (Littelfuse 221000 (=215000 + pins) I2t 82.85 A2s) on the power supply input to the Indoor Unit. These fuses are mounted for safety reasons and can only be exchanged by the manufacturer. The internal fuses are sufficient for protection of the equipment, external fuses are not required.
If additional, external, fuses are desired, the following applies:
• For 48 V power supplies, use a 2 A fast fuse.
• For 24 V power supplies, use a 3.5 A fast fuse.
Power Consumption
The maximum power consumption is 50 W per radio terminal (dependent on traffic capacity).
CAUTION!
The supply voltage must not go below 20 V or exceed 72 V! This is the maximum voltage tolerance of the radio terminal.
WLDM001EnC
Installation ManualChapter 2: Site Requirements
WLD
Grounding of Indoor Equipment
Usually, the Indoor Unit is grounded via the rack’s connection to ground. If the rack is not connected to ground, or if the rack is coated so that there is no direct connection between the Baseband Unit and the rack, the Indoor Unit must be grounded via a separate cable. The cable is connected to the M6 grounding lug located on the front of the Baseband Unit (BBU). For this purpose, it is recommended to use a flat copper braid.
If an Indoor Unit is connected to another Indoor Unit that is not hosed in the same magazine, a short grounding cable (< 0.5 m) must be used between the grounding lugs of the two units.
Indoor Electromagnetic Interference (EMC)
The Indoor Unit meets the electromagnetic interference requirements of ETS 300 385.
M001EnC 13
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 2: Site Requirements
14
Indoor Environmental Requirements
The Indoor Unit meets the requirements of ETS 300 019-3.
Table 2 Requirements for indoor temperature and humidityCharacteristic Value
Temperature:Single units and rack mounted units with >1U spacing (above and below).
-25°C to +55°C1
1. Refers to the temperature 5 mm from the equipment surface.
Rack mounted units with <1U spacing. -25°C to +45°C1
Relative Humidity2:
2. See ETS 300 019 for detailed requirements for humidity vs. temperature.
95% RH
WLDM001EnC
Installation ManualChapter 2: Site Requirements
WLD
Outdoor Requirements
Outdoor Space Requirements
The standard method for mounting the Radio Frequency Unit (RFU) and the Antenna Unit is to mount them together as one unit.
Table 3 Space requirements for the Radio/Antenna Unit
Note: For 4 ft. and 6 ft. antennas, see the antenna installation manual delivered with the product.
Antenna Unit A B C D E1
1. Including adjustment and locking screws.
1 ft. HP antenna 310 mm 395 mm 440 mm 125 mm 180 mm2 ft. HP antenna 430 mm 640 mm 575 mm 125 mm 180 mm
M001EnC 15
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 2: Site Requirements
16
Mast Requirements
The mast pole must be located in a vertical position.
Table 4 Requirements for antenna mast
Outdoor Power Requirements
Power supply to the outdoor equipment is fed from the BBU via the radio cable. There is no need for a separate power supply.
Grounding of Outdoor Equipment
Grounding of Antenna/Radio Frequency Unit
The Antenna/RF Unit is grounded via the mast’s connection to ground. To get sufficient protection against lightning surges, the radio cable leading from the Antenna/RF Unit should be bonded to mast ground less than 1 m from the Antenna/RFU. For this purpose, it is recommended to use the applicable accessory in the Grounding Kit.
Requirement Value
Mounting pole diameter 15–115 mmMast stability: variation in direction of antenna
≤ 0.25°
WLDM001EnC
Installation ManualChapter 2: Site Requirements
WLD
Grounding of Radio Cable
Besides bonding the radio cable to ground 1 m from the RFU, see Grounding of Antenna/Radio Frequency Unit above, it is recommended to ground the radio cable at the foot of the mast and before entering a building. If the distance between two of these grounding points exceeds 50 m, it is recommended to bond/ground the cable also at every 50 m.
Outdoor Electromagnetic Interference (EMC)
The outdoor equipment meets the electromagnetic interference requirements of ETS 300 385.
Outdoor Environmental Requirements
The outdoor equipment meets the requirements of ETS 300 019-4.
Table 5 Requirements for outdoor temperature and humidityCharacteristic Value
Operating temperature1
1. Excluding solar radiation.
-45°C to +45°C
Relative Humidity2
2. See ETS 300 019 for detailed requirements for humidity vs. temperature.
100% RH
M001EnC 17
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 3: Indoor Installation
18
Chapter 3: Indoor Installation
Tools Required for Indoor Installation
• Pozidrive screwdriver PZ2 and PZ3
• Necessary tools for assembling the cables and connectors.
WLDM001EnC
Installation ManualChapter 3: Indoor Installation
WLD
Indoor Equipment
Table 6 Indoor equipmentPos. Part Part Number Qty.
1 Indoor Unit, consisting of: – 1a) Baseband Unit (BBU) 1
ITU WAAB00101/xx
b) Traffic Interface Unit (TIU) WAADxxxyyy/zz 12 Installation Kit for 19" rack,
consisting of:WMSA001 1
a) Rack Mount Screw (M6x16, PZ3) – 4
b) Rack Mount Captive Nut – 4c) DC Power Connector and Hood – 1d) Jumper Cable to Mast Cable WUKA109/025 1
M001EnC 19
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 3: Indoor Installation
20
Indoor Accessories
Table 7 Indoor accessories
Pos. Part Part Number Qty.
1 2U Magazine WMMA001/02 12 2U Magazine Installation Kit,
consisting of:WMSA002/02 1
a) Rack Mount Screw (M6x16, PZ3) – 4b) Rack Mount Captive Nut – 4c) Mounting Rail Screw (M4x8, PZ2) – 4d) Mounting Rail – 83 6U Magazine WMMA001/06 12 6U Magazine Installation Kit,
consisting of:WMSA002/06 1
a) Rack Mount Screw (M6x16, PZ3) – 8b) Rack Mount Captive Nut – 8
WLDM001EnC
Installation ManualChapter 3: Indoor Installation
WLD
More accessories are available, for details see the "Accessories and Spare Parts" list provided by Allgon Microwave AB.
c) Mounting Rail Screw (M4x8, PZ2) – 24d) Mounting Rail – 124 ETSI Rack Mounting Kit 1U WMSA003 14 ETSI Rack Mounting Kit 2U WMSA016 14 ETSI Rack Mounting Kit 6U WMSA013 1- SMZ-BNC Converter Cable, 5 m WUKA105/050 1- ITU Impedance Converter Cable
8x2, 37 pin DSUB plug (male) to BNC jack (female) connectors, 2 m
WUKB001/2 1
- ITU Impedance Converter Cable 1x2, 9 pin DSUB plug (male) to BNC plug (male) connectors, 2 m
WUKB002/2 1
Pos. Part Part Number Qty.
M001EnC 21
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 3: Indoor Installation
22
Baseband Unit
Interfaces on the Baseband Unit
Table 8 Baseband Unit interfacesPos Interface Function
1 User interface Control panel with keypad and display for configuring the radio terminal without a PC, and status LEDs for monitoring of the radio terminal. For further information about the control panel, refer to the Operation and Maintenance Manual (WLDM002).
2 9 pin D-SUB jack (female)
LM/NMS 1 port, used for connecting a PC or for daisy-chaining radio terminals. The interface standard is RS-232/DCE.
3 9 pin D-SUB plug (male)
MODEM/NMS 2 port, used for modem connection or for daisy-chaining radio terminals. The interface standard is RS-232/DTE.
4 TNC jack (female)
Used for connection to the RFU.
5 M6 grounding lug Used for grounding of the Indoor Unit.
WLDM001EnC
Installation ManualChapter 3: Indoor Installation
WLD
6 2 pin D-SUB plug (male)
DC power connector.
7 26 pin D-SUB High Density jack (female)
External I/O port, used for monitoring and control of external functions, and for status/alarm reporting.
8 RJ-45 jack (female)
10baseT/100BaseTX Ethernet port, used for connection to a LAN. The interface standard is Ethernet/DTE.
9 Sofix1/Metral2 connectors
Used for connection of the TIU.
1. Ericsson designation2. Berg designation
Pos Interface Function
M001EnC 23
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 3: Indoor Installation
24
Traffic Interface Unit
All traffic interfaces are located on the TIU of the Indoor Unit. The interfaces are compliant with ITU-T G.703. Three different types of TIUs are available:
• E3 + E1interface
• 4, 8 or 17 x E1 interface
• Ethernet + E1 interface
CAUTION!
When mounting the TIU in the BBU, the two screws must be fastened by hand! Do not use any tools or excessive force!
WLDM001EnC
Installation ManualChapter 3: Indoor Installation
WLD
E3+ E1 Interfaces
Traffic Interface Unit, E3 + E1 interface
Table 9 Traffic Interface Unit, E3 + E1 interface
The TX connector is grounded by default. If you wish to ground also the RX connector, use the Earth Washer delivered with the E3 TIU. Place the Earth Washer behind the two SMZ jacks on the TIU, so that the RX and TX connectors are joined.
Pos Connector Function
1 9 pin D-SUB jack (female), balanced, 120 Ω
Traffic Channel (E1:17)
2 SMZ jack (female), unbalanced, 75 Ω
Traffic Channel (E3:1), outgoing direction (TX)1
1. The channel number and the direction (TX/RX) for the SMZ connectors are indicated on the TIU.
3 SMZ jack (female), unbalanced, 75 Ω
Traffic Channel (E3:1), incoming direction (RX)1
4 9 pin D-SUB jack (female), balanced, 120 Ω
Overhead Channel (OH:1)
5 9 pin D-SUB jack (female ), balanced, 120 Ω
Overhead Channel (OH:2)
M001EnC 25
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 3: Indoor Installation
26
To do this you have to unscrew the nuts of the SMZ jacks, place the earth washer behind the nuts, and then put the SMZ jacks back in place again.
17 x E1 Interfaces
Traffic Interface Unit, 17xE1 interface
Table 10 Traffic Interface Unit, 17 x E1 interface Pos Connector Function
1 9 pin D-SUB jack (female),balanced, 120 Ω
Traffic Channel (E1:17)
2 37 pin D-SUB jack (female), balanced, 120 Ω
Traffic Channel (E1:1–8)
3 37 pin D-SUB jack (female), balanced, 120 Ω
Traffic Channel (E1:9–16)
4 9 pin D-SUB jack (female), balanced, 120 Ω
Overhead Channel (OH:1)
5 9 pin D-SUB jack (female), balanced, 120 Ω
Overhead Channel (OH:2)
WLDM001EnC
Installation ManualChapter 3: Indoor Installation
WLD
Ethernet + E1 Interfaces
Traffic Interface Unit, Ethernet + E1 interface (Ethernet + 4xE1)
Table 11 Traffic Interface Unit, Ethernet+ E1 interface Pos Connector Function
1 RJ-45 jack (female), unbalanced
Traffic Channel (10/100baseT)
2 LED, multicolor ON, green: Link available.ON, orange: Link active.
3 37 pin D-SUB jack (female), balanced, 120 Ω
Traffic Channel (E1:9–12)
4 9 pin D-SUB jack (female), balanced, 120 Ω
Overhead Channel (OH:1)
5 9 pin D-SUB jack (female), balanced, 120 Ω
Overhead Channel (OH:2)
M001EnC 27
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 3: Indoor Installation
28
Mounting the Indoor Unit
There are three different ways of mounting the Indoor Unit:
• single unit mounted in 19" rack;
• single unit mounted in ETSI rack; and
• 2–6 units in a common backplane magazine for 19" rack.
The following sections describe Single Unit Mounting in 19" Rack and Common Backplane Mounting In Magazine for 19" Rack.
WLDM001EnC
Installation ManualChapter 3: Indoor Installation
WLD
‰ Single Unit Mounting in 19" Rack
Optional positions for mounting the brackets
The brackets can be mounted in four different positions (A–D) to make the Indoor Unit fit in your particular rack set-up. Use a Pozidrive screwdriver PZ2 if you want to move the brackets.
Mounting a single Indoor Unit in a 19” Rack
A B C D
M001EnC 29
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 3: Indoor Installation
30
‰ Common Backplane Mounting In Magazine for 19" Rack
Preparing the Indoor Unit for mounting in magazine
Common backplane mounting of Indoor Units in 2U or 6U Magazine
WLDM001EnC
Installation ManualChapter 3: Indoor Installation
WLD
The numbering of the Indoor Units in the magazine starts at the bottom of the magazine; unit number 1 is at the bottom and unit 2 (6) is at the top.
‰ Grounding the Indoor Unit
Usually, the Indoor Unit is grounded via the rack’s connection to ground. If the rack is not connected to ground, or if the rack is coated so that there is no direct connection between the Baseband Unit and the rack, the Indoor Unit must be grounded via a separate cable. The cable is connected to the M6 grounding lug located on the front of the Baseband Unit (BBU). For this purpose, it is recommended to use a flat copper braid.
Grounding the Indoor Unit via a separate cable
Indoor Units mounted in a magazine can be grounded by connecting the grounding cable to the M6 grounding lug located on the magazine.
M001EnC 31
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 3: Indoor Installation
32
Grounding all Indoor Units in a magazine via a separate cable
WLDM001EnC
Installation ManualChapter 3: Indoor Installation
WLD
Installing the Cables for the Indoor Unit
Note: The connector manufacturer’s instructions for mounting of the connectors must always be followed!
Definition of TX and RX Signals
TX signals are defined as signals coming out of the TIU.
RX signals are defined as signals going into the TIU.
‰ Installing Cables for Unbalanced Traffic Interface SMZ Connectors
Mount the SMZ connectors on the cables and connect the cables to the Indoor Unit. The channel number and the direction (TX/RX) for each SMZ connector are indicated on the TIU.
‰ Installing Cables for Balanced Traffic Interface D-SUB Connectors
Mount the connectors on the cables according to the pin allocation listed in the tables below and connect the cables to the Indoor Unit.
RX TX
M001EnC 33
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 3: Indoor Installation
34
Note: The cables for the balanced traffic interface must be of type shielded twisted pair!
Traffic Channel D-SUB Connectors (E1:1–16)
37 pin D-SUB external cable connector (rear view)
Table 12 Traffic channel connector pin allocationChannel
no. TX Pin no. RX Pin no. Connector
1 19 / 37 18 / 36 E1:1–82 17 /35 16 / 34 E1:1–83 15 / 33 14 / 32 E1:1–84 13 / 31 12 / 30 E1:1–85 11 / 29 10 / 28 E1:1–86 9 / 27 8 / 26 E1:1–87 7 / 25 6 / 24 E1:1–88 5 / 23 4 / 22 E1:1–89 19 / 37 18 / 36 E1:9–1610 17 / 35 16 / 34 E1:9–1611 15 / 33 14 / 32 E1:9–16
WLDM001EnC
Installation ManualChapter 3: Indoor Installation
WLD
Traffic Channel D-SUB Connector (E1:17)
9 pin D-SUB external cable connector (rear view)
Table 13 Traffic channel connector pin allocation
12 13 / 31 12 / 30 E1:9–1613 11 / 29 10 / 28 E1:9–1614 9 / 27 8 / 26 E1:9–1615 7 / 25 6 / 24 E1:9–1616 5 / 23 4 / 22 E1:9–16
Channel no. TX Pin no. RX Pin no. Connector
17 5 / 9 4 / 8 E1:17
Channel no. TX Pin no. RX Pin no. Connector
M001EnC 35
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 3: Indoor Installation
36
‰ Installing Cables for Traffic Interface Ethernet Connectors
Mount the RJ-45 connectors on the cables and connect the cables to the Indoor Unit.
RJ-45 external cable connector (rear view)
Table 14 Traffic channel connector pin allocation
‰ Installing Cables for Overhead Channel D-SUB Connectors (OH:1, OH:2)
The two 64 kbps OH channels are compliant with ITU-T G.703 requirements for co-directional interfaces.
Mount the connectors on the cables according to the pin allocation listed in the table below and connect the cables to the Indoor Unit. Refer to the figure 9 pin D-SUB external cable connector (rear view) above for the pin numbering.
Channel no. TX Pin no. RX Pin no. Connector
1 3 / 6 1 / 2 10 BASE T / 100 BASE TX
WLDM001EnC
Installation ManualChapter 3: Indoor Installation
WLD
Table 15 Overhead channel connector pin allocation
‰ Installing a Cable for the External I/O D-SUB Connector
The External I/O port consists of the following software configurable interfaces:
• 4 relay outputs for status/alarm functions;
• 8 digital inputs for monitoring of external functions; and
• 8 digital outputs for control of external functions.
For information on how to configure the inputs and outputs of the External I/O port, refer to the Operation and Maintenance Manual (WLDM002).
Mount the connector on the cable according to the pin allocation listed in the table below and connect the cable to the Indoor Unit.
Channel no. TX Pin no. RX Pin no. Connector
1 5 / 9 4 / 8 OH:12 5 / 9 4 / 8 OH:2
M001EnC 37
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 3: Indoor Installation
38
26 pin D-SUB external cable connector (rear view)
Table 16 External I/O connector pin allocation
‰ Installing a DC Power Cable
External DC power cable connector (rear view)
Signal Pin no. Remarks
Relay 1 1–2 Pmax 30 W, Imax 1 A, Umax 60 VDCRelay 2 3–4
Relay 3 5–6Relay 4 7–8Digital Inputs
10–17 UIL=max 0.4 V, UIH=max 5.0 V,IIL=-0.3 mA
Ground 18Digital Outputs
19–26 UOL=max 0.8 V @ 200µΑUOH=min 2.4 V @ -200µΑ
WLDM001EnC
Installation ManualChapter 3: Indoor Installation
WLD
The power cable should be AWG 16/20 or equivalent. The two wires can be connected to the DC power plug with any polarity.
Use a crimping tool to mount the connector pins onto the cable.
Note: Do not connect the power cable to the Indoor Unit at this stage!
Indoor Radio Cable
It is recommended to mount a surge arrester at the wall entrance as an adapter between the indoor and outdoor radio cable. The surge arrester should be mounted in a copper plate with a low resistance connection (< 0.1 Ω) to ground on the outside. This will improve the protection of the indoor equipment in case of lightning strikes.
It is also recommended to fasten the length of the indoor radio cable to the rack or in an existing cable bundle.
Table 17 Recommended indoor radio cable and connectorsCable/Connector Manufacturer/Model
Indoor Radio Cable RG214 or RG4001
1. In compliance with WPEK101002.
Surge Arrester N jack (female)–N jack (female) bulkhead 20 kA (8/20 µs pulse)
Surge Arrester Capsule Ustatic = 90 V, Udynamic < 800 V
M001EnC 39
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 3: Indoor Installation
40
Accessories and Spare Parts for Lightning Protection and Grounding
Table 18 Accessories and Spare Parts for Lightning Protection and Grounding
‰ Connecting the Indoor Radio Cable
1. Mount the coaxial connectors on the indoor radio cable.2. Connect the indoor radio cable to the Indoor Unit and the
adapter between the indoor and outdoor radio cable.
Part Part Number
Lightning Protection Unit, N to N plug (male) connector
WPEJ105006
Surge Arrester (Fuse) for Lightning Protection Unit (spare part to WPEJ105006)
WPET60002/90
WLDM001EnC
Installation ManualChapter 4: Outdoor Installation
WLD
Chapter 4: Outdoor Installation
Tools Required for Outdoor Installation
• Pozidrive screwdriver PZ2
• 17 mm torque wrench
• Necessary tools for assembling the cables and connectors.
M001EnC 41
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 4: Outdoor Installation
42
Outdoor Equipment
Table 19 Outdoor equipmentPos. Part Part Number Qty.
1 Radio Frequency Unit (RFU)
WAAAxxxyy/zz 1
2 Antenna Unit (including Mast Mounting Bracket1)
1. Fits a mast of diameter 50 to 115 mm (2 to 4.5").
WAAFxxxyy/zz 1
WLDM001EnC
Installation ManualChapter 4: Outdoor Installation
WLD
Outdoor Accessories
Table 20 Outdoor Accessories Parts Part Number
AGC Cable, BNC plug (male) to multimeter plugs (male), 1 m
WUKA104/010
M001EnC 43
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 4: Outdoor Installation
44
Choosing Vertical or Horizontal Polarization
The position of the RFU determines the polarization of the radio signal. The handle serves as an indicator: horizontal handle = horizontal polarization, vertical handle = vertical polarization.
Position of coaxial connector for vertical polarization
Position of coaxial connector for horizontal polarization
The coaxial connector on the back of the Antenna Unit must fit the connector on the RFU. Use a Pozidrive screwdriver PZ2 if you need to move the connector on the Antenna Unit.
WLDM001EnC
Installation ManualChapter 4: Outdoor Installation
WLD
Note: Do not remove the screw or the washer when you move the connector.
CAUTION!
For horizontal polarization, make sure that the coaxial cable runs in the dedicated slot on the back of the Antenna Unit!
M001EnC 45
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 4: Outdoor Installation
46
Mounting the RF Unit on the Antenna Unit
‰ Mounting the Radio Frequency Unit on the Antenna Unit
1. Remove the plastic covers for moisture protection from the waveguides on the RFU and the Antenna Unit.
Mounting the Radio Frequency Unit on the Antenna Unit.2. Hook the circular part of the RFU, containing the
waveguide, onto the locking device on the back of the Antenna Unit.
CAUTION!
After the plastic covers have been removed, make sure that no moisture enters the waveguides.
WLDM001EnC
Installation ManualChapter 4: Outdoor Installation
WLD
Note: The direction of the handle on the RFU must be in accordance with the desired polarization! Make sure that the coaxial connector on the back of the RFU fits the connector on the back of the Antenna Unit!
3. Gently push the RFU as far as it can go into the Antenna Unit.
4. Use the 17 mm wrench to fasten the RFU by turning the locking screw on the bottom of the antenna 1/4 turn. You will feel a gentle click when the RFU is locked in position. Stop turning when you feel the resistance increasing.
CAUTION!
Do not continue turning the locking screw when you feel the resistance increasing!
CAUTION!
When you carry or lift the Antenna/RF Unit, use the handle on the top of the antenna! The handle on the back of the RFU is not intended for this purpose!
M001EnC 47
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 4: Outdoor Installation
48
Choosing Left or Right Side Antenna Mounting
Mounting the M10 screws on the antenna
Two M10 screws are used for fastening the Antenna/RF Unit on the Mast Mounting Bracket. They can be mounted on either side of the antenna.
• Make sure that the screws are placed in the screw holes on the correct side of the Antenna Unit, and that there is enough space to allow mounting of the Antenna/RF Unit to the Mast Mounting Bracket.
Note: Do not tighten the screws at this stage.
WLDM001EnC
Installation ManualChapter 4: Outdoor Installation
WLD
Fastening the Mast Mounting Bracket
Recommended mounting of the Antenna/RF Unit
It is recommended to mount the Antenna/RF Unit within a limiting angle of 45° originating from the top of the mast. This will protect the Antenna/RF Unit from direct lightning strikes.
If the recommended angle cannot be obtained, a mast pole of at least 1 m should be attached to the top of the mast, to secure the desired level of protection.
Fastening the Mast Mounting Bracket
‰ Fastening the Mast Mounting Bracket
1. Position the Mast Mounting Bracket around the mast.
4545
M001EnC 49
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 4: Outdoor Installation
50
2. Use a compass to roughly align the Mast Mounting Bracket so that the antenna will point in the radio link path.
Fine tuning will be performed when you reach section Antenna Alignment on page 103. The maximum possible fine tuning adjustment is ±15 degrees in azimuth and ±20 degrees in elevation.
3. Rotate the clamps until they latch onto the mount bolts.
4. Use the 17 mm torque wrench two tighten the two M10 nuts.
Note: The torque must be 22 Nm ± 10% when tightening the nuts!
WLDM001EnC
Installation ManualChapter 4: Outdoor Installation
WLD
Mounting the Antenna/RF Unit on the Mast Mounting Bracket
M10 screws used for mounting the Antenna/Radio Frequency Unit.
‰ Mounting the Antenna/Radio Frequency Unit on the Mast Mounting Bracket
1. Mount the Antenna/RF Unit on the Mast Mounting Bracket by sliding in the two captive M10 screws on the Antenna through the dedicated slots on the bracket plate.
2. When the screws are in position, use the 17 mm torque wrench to tighten the two captive screws. Locate the screws fully, before tightening the screws.
Note: The torque must be 39.2 Nm ± 10% when tightening the nuts!
M001EnC 51
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 4: Outdoor Installation
52
Grounding the Antenna/RF Unit
The Antenna/RF Unit is grounded via the mast’s connection to ground. To get sufficient protection against lightning surges, the radio cable leading from the Antenna/RF Unit should be bonded to mast ground less than 1 m from the Antenna/RFU. For this purpose, it is recommended to use the applicable accessory in the Grounding Kit.
Outdoor Accessories for Lightning Protection and Grounding
Table 21 Outdoor Accessories for Grounding
Outdoor Radio Cable Installation
When using an RG214 or RG213 foil complying with the Allgon specification (WPEK101002), the maximum length of the outdoor radio cable is 300 m. Longer cables can be connected if they have better performance. For details, contact Allgon Technical Support.
Table 22 Recommended outdoor radio cable and connectors
Part Part Number
Grounding Kit WMSA014
Cable/Connector Manufacturer/Model
Outdoor Radio Cable RG214 or RG213 foil1, Ø 10 mm
1. In compliance with WPEK101002
Outdoor Connector Type N, plug (male) crimp
WLDM001EnC
Installation ManualChapter 4: Outdoor Installation
WLD
‰ Connecting the Outdoor Radio Cable
1. Mount the coaxial connectors on the outdoor radio cable.
Note: The connector manufacturer’s instructions for mounting of the connectors must always be followed!
2. Connect the Outdoor Unit to the Indoor Unit via the Jumper Cable.
To seal the cable joint properly between the coaxial cable and the RFU, it is recommended to use the Cold Shrink Weatherproofing Kit accessory.
Outdoor Environmental Accessories
Table 23 Outdoor Environmental Accessories
‰ Grounding the Radio Cables
Besides bonding the radio cable to mast ground 1 m from the RFU, see Grounding the Antenna/RF Unit above, it is recommended to ground the cable at the foot of the mast and before entering a building. If the distance between two of these grounding points exceeds 50 m, it is recommended to bond/ground the radio cable also every 50 m. See the figure below.
If a surge arrester is mounted in the wall, it should be mounted in a copper plate with a low resistance connection (< 0.1 Ω) to ground on the outside. This will improve the protection of the indoor equipment in case of lightning strikes.
Part Part Number
Cold Shrink Weatherproofing Kit WMSA015
M001EnC 53
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 4: Outdoor Installation
54
Note: If the In- and Outdoor Units, and the radio cable are grounded in accordance with the recommendations, the Allgon Microwave Radio will be equipped to resist severe lightning surges.
Recommended grounding of the radio cable
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
Chapter 5: Start-up and Configuration
The radio terminal can be managed either locally or remotely. When accessing the radio terminal for the first time, you must manage it locally. During the initial configuration, you should configure it for remote management to be able to manage it remotely subsequently.
Note: You only have to carry out the instructions in this section the first time you access the radio terminal. If you have accessed the radio terminal before and configured the ports that you will use for communicating with it, proceed to section Accessing the Web Pages on page 78.
The easiest way to configure the radio terminal is by using a web browser. In order to establish communication between the web browser and the radio terminal you must first configure the communication interface.
In some cases you may need to use a text terminal program for this purpose. The instructions in this manual are written for the HyperTerminal program which is included in Windows 95/98/2000/NT. However, other communication applications can also be used.
The management connection depends on whether the radio terminal should have static or dynamic IP addresses. For more information about this, refer to the Operation and Maintenance Manual (WLDM002).
M001EnC 55
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
56
‰ Accessing the radio terminal for the first time
1. Switch on the radio terminal. Refer to section Start-up and Shut-down on page 61.
2. Connect the radio terminal to a local manager. Refer to section Local Management Connection on page 63.
3. Perform initial radio terminal configuration. Refer to section Initial Radio Terminal Configuration on page 79.
4. Connect the radio terminal to a remote manager according to one of the following alternatives:
– For set-up of a TCP/IP network on an Ethernet LAN, refer to section Connecting to Ethernet LAN on page 90.
– For set-up of a TCP/IP network via a modem, refer to section Connecting via Modem on page 92.
– For set-up of a TCP/IP network via an ECC, refer to section Connecting via ECC on page 95.
Alternatively, you may connect the radio terminal to another radio terminal already connected to a remote manager. Do this according to one of the following alternatives:
– For set-up of a TCP/IP network on a daisy chain, refer to section Daisy-chaining on page 101.
– For set-up of a TCP/IP network on an Ethernet LAN, refer to section Connecting to Ethernet LAN on page 90.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
Equipment Required for Configuration
Table 24 lists the equipment required for configuration of the radio terminal on site, i.e. to establish a local management connection.
Table 25–Table 29 list additional equipment required to establish a remote management connection. The required equipment depends on which type of remote management network you are going to install the radio terminal in.
Table 24 Equipment for local management connectionEquipment Description
PC This manual describes how to use a PC with Windows installed as local manager. Other platforms can be used, but this is not described.
Windows 95/98, 2000 or NT 4.0 Operating System
Operating system for PC. Other operating systems are possible.
Web Browser Used as operator interface. The web browser could be Netscape Navigator 4.x or Internet Explorer 4.x, or 5.x.
Text Terminal Used as operator interface to send commands directly to the Management Information Base via RS-232 serial interface. The text terminal could be HyperTerminal, which is usually included in Windows, or equivalent.
Dial Up Networking Software
Used for dialling up via the serial port. This software is included in Windows but not always installed by default.
M001EnC 57
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
58
Table 25 Additional equipment for remote management, Ethernet LAN connection
Table 26 Additional equipment for remote management, modem connection
The file "amr.inf" Supplied by Allgon AB.
Serial PC Cable For connection of the PC to the radio terminal. The interface in the radio terminal end should be a 9 pin D-SUB plug (male). The interface in the other end should fit the serial port of your PC (e.g. COM1).
Equipment Description
TCP/IP-based LAN
For connection of a remote manager. For further information, refer to the Operation and Maintenance manual (WLDM002).
UTP Cable For connection of the radio terminal to an Ethernet LAN.
If two radio terminals are to be connected to each other, connect them directly using a null modem UTP cable (DTE-wired in both ends).
Equipment Description
Modems For placement at the radio terminal site and a remote manager site respectively. For further information, refer to the Operation and Maintenance manual (WLDM002).
Equipment Description
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
Table 27 Additional equipment for remote management, ECC connection
Serial Modem Cable
For connection of a modem to the radio terminal. The interface in the radio terminal end should be a 9 pin D-SUB jack (female). The interface in the other end should fit the serial port of your modem. For further information, refer to the Operation and Maintenance manual (WLDM002).
Equipment Description
Ethernet E1 Router
For routing of ECCs to a remote manager. For further information, refer to the Operation and Maintenance manual (WLDM002).
Equipment Description
M001EnC 59
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
60
Status LEDs
LEDs on the control panel of the Baseband Unit
Table 28 Baseband Unit LEDsLED State Function
ACTIVE1 OFF The radio terminal is starting up or reconfiguring (INACTIVE state).
Blinks 1 Hz The radio terminal is ready to transmit (STANDBY state).
Blinks 15 Hz The radio terminal is transmitting (ACTIVE state).
TEST Blinks 15 Hz The radio terminal is in TEST mode.
WARNING ON An alarm of severity WARNING2 has been generated in the radio terminal.
Blinks 3 Hz An alarm of severity MINOR2 has been generated in the radio terminal.
ESC ALT OKTEST
ACTIVE
ALARM
WARNING
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
Start-up and Shut-down
‰ Switching ON the Radio Terminal
1. Make sure that the power supply feeding the BBU has a nominal output voltage somewhere between 24 V and 60 V, any polarity.
2. Connect the power cable to the BBU.3. During start-up, the TEST LED blinks with 15 Hz. Wait
until the system is in STANDBY state (this normally takes
ALARM ON An alarm of severity MAJOR2 has been generated in the radio terminal.
Blinks 3 Hz An alarm of severity CRITICAL2 has been generated in the radio terminal.
1. The radio terminal can be in either NORMAL mode or in TEST mode. The blinking pattern for the ACTIVE LED is the same in both modes.
2. These alarms are software-configurable. For further information, refer to the Operation and Maintenance manual (WLDM002).
CAUTION!
The supply voltage must not go below 20 V or exceed 72 V! This is the maximum voltage tolerance of the radio terminal!
LED State Function
M001EnC 61
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
62
around 30 seconds); the ACTIVE LED should blink (1 Hz or 15 Hz) and all other LEDs should be switched off before you start to configure the radio terminal.
‰ Switching OFF the Radio Terminal
Before you have started to configure the radio terminal via the web interface, you can switch off the radio terminal at any time by disconnecting the power cable.
After you have reached section Accessing the Web Pages on page 78, and have started to configure the radio terminal via the web interface, you should do the following to prevent the radio terminal from transmitting transients at switch off:1. Select Traffic → RF Channel; set "TX Mute" to Forced
mute.
2. Disconnect the power cable.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
Local Management Connection
Before connecting the radio terminal to local management equipment, in this case a PC, you must prepare the PC. The setup procedure depends on which operating system you are using on the PC:
• To setup a PC with Windows NT, refer to section Setting up the PC with Windows NT on page 63 below.
• To setup a PC with Windows 2000, refer to section Setting up the PC with Windows 2000 on page 68. This setup procedure can be used for a PC with Windows 95/98 as well with some minor adjustments.
When this is done, connect the radio terminal locally by setting up a point-to-point network between the radio terminal and the PC using a static IP address. Refer to section Terminal Access on page 74.
Setting up the PC with Windows NT
This section describes how to set up your PC to be able to connect it locally to any radio terminal. You only have to carry out the instructions in this section once.
‰ Configuring Serial Port (Windows NT)
You must create a text terminal session with the correct settings for the serial port that will be used for the connection to the radio terminal.
1. Start the text terminal program (HyperTerminal or equivalent) on your PC.
M001EnC 63
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
64
2. Select File → New Connection. The Connection Description dialog box appears.
3. Enter SerialPortAMR in the Name box, and select an icon for the connection in the Icon box.
4. Click OK. The Connect To dialog box appears.
5. Select COM1 or equivalent serial port in the Connect using box.
6. Click OK. The COM1 Properties dialog box appears.
7. Enter the following settings for the serial port:
– Bits per second = 115200 (other values are possible, refer to the Operation and Maintenance Manual (WLDM002))
– Data bits = 8
– Parity = None
– Stop bits = 1
– Flow control = Hardware8. Click OK. 9. Select File → Save to save the session.
10. Select File → Exit to exit the HyperTerminal program and close the connection.
11. You have now created a text terminal session for the serial port that will be used for the connection to the radio terminal. Proceed to section Installing Null Modem Driver (Windows NT) below.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
‰ Installing Null Modem Driver (Windows NT)
The radio terminal is seen as a telephone modem by the PC. You must therefore install a null modem driver on your PC.
Note: Before you start installing the null modem driver, make sure that the file "amr.inf" is stored on your PC.
1. In the Windows Start menu, select Settings → Control panel.
2. Double click on the Modems icon.
3. Select Add....4. Select Other. Click Next >.5. Select Don’t detect my modem, I will select it from a list.
Click Next >.
6. Click Have disc...7. Select the path to where the file “amr.inf” is stored. Click
OK.
8. Select the Allgon Microwave Radio modem. Click Next >.
9. Select COM1 or equivalent serial port that you want to connect the modem to. Click Next >.
10. Click Finish.11. If the dialog box “Modem properties” does not
automatically appear, double click on the Modem icon in the Control panel.
12. Click Properties.13. Under General, select Max speed = 115200(other values
are possible, refer to the Operation and Maintenance Manual (WLDM002)).
M001EnC 65
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
66
14. Under Connection, select Data Bits = 8, Parity = None, Stop bits = 1. Make sure that Wait for dial tone is unchecked.
15. Click Advanced. Uncheck Use error control and Use flow control.
16. Click OK two times.17. Click Close.18. Restart your computer for the changes to take effect.
19. Proceed to section Configuring Dialling Up via the Serial Port (Windows NT) below.
‰ Configuring Dialling Up via the Serial Port (Windows NT)
The serial port that will be used as a connection must be configured for dialling up the radio terminal.
1. On your PC, double click on the Dial Up Networking icon located under the icon My computer on the desktop, or under My computer in the Explorer.
2. Enter DialUpAMR as the Entry name in the dialog box "Name the New phonebook entry". Click Next >.
3. Check The non-Windows NT server I am calling expects me to type login information after connecting, or to know TCP/IP addresses before dialling.; all other boxes should be unchecked. Click Next >.
4. Leave the text box "Telephone number" empty. If the program requires that you enter a telephone number, enter any random number. This is of no importance for the function of the radio terminal modem. Click Next >.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
5. Select Point-to-Point Protocol (PPP). Click Next >.
6. In the "Login script" dialog box, select None. Click Next >.7. Enter the IP address of your computer in the text box
marked "My IP address". Click Next >.
8. If there is a DNS server in your network, enter its IP address in the dedicated text box. If you have no DNS server, enter 0.0.0.0 in this text box. Click Next >.
9. Click Finish.
10. In the dialog box "Dial Up Networking", select More → Edit entry and modem properties....
11. Under Basic, make sure the Allgon Microwave Radio modem is chosen in the box marked "Dial Using:" Sometimes the Allgon Microwave Radio modem cannot be found among the modems listed in the box. In this case, do as follows:
– Right-click the Network Neighborhood icon on the desktop, and select Properties.
– In the Properties dialog, select Services → Remote Access Service → Properties, and then click Add.
– Select "Allgon Microwave Radio" and click OK.
– Click Continue. The modem is then made available in the "Dial Using:" box under Basic.
12. Click Configure.13. Select Initial Speed (bps) = 115200 (other values are
possible, refer to the Operation and Maintenance Manual (WLDM002)).
14. Check Enable hardware flow control.
M001EnC 67
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
68
15. Click OK.
16. Click Close.
Your PC is now set up for local management and may be connected to a radio terminal. Proceed to section Terminal Access on page 74.
Setting up the PC with Windows 2000
This section describes how to set up a PC with Windows 2000 to be able to connect it locally to a radio terminal. This setup procedure can be used for a PC with Windows 95/98 as well with some minor adjustments.
‰ Configuring Serial Port (Windows 2000)
You must create a text terminal session with the correct settings for the serial port that will be used for the connection to the radio terminal.1. Start the text terminal program (HyperTerminal or
equivalent) on your PC.2. Select File → New Connection. The Connection
Description dialog box appears.3. Enter SerialPortAMR in the Name box, and select an icon
for the connection in the Icon box.4. Click OK. The Connect To dialog box appears.5. Select COM1 or equivalent serial port in the Connect using
box.
6. Click OK. The COM1 Properties dialog box appears.7. Enter the following settings for the serial port:
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
– Bits per second = 115200 (other values are possible, refer to the Operation and Maintenance Manual (WLDM002))
– Data bits = 8
– Parity = None
– Stop bits = 1
– Flow control = Hardware8. Click OK.
9. Select File → Save to save the session.10. Select File → Exit to exit the HyperTerminal program and
close the connection.
11. You have now created a text terminal session for the serial port that will be used for the connection to the radio terminal. Proceed to section Installing Null Modem Driver (Windows 2000) below.
‰ Installing Null Modem Driver (Windows 2000)
The radio terminal is seen as a telephone modem by the PC. To be able to dial up the radio terminal, you must install a null modem driver on your PC.
Before you install the null modem driver you must make it possible to install drivers that are not Microsoft signed on your computer.1. Right-click on the "My computer" icon on your computer
desktop and select Properties from the menu. The System Properties dialog box appears.
2. Select Hardware.
M001EnC 69
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
70
3. Under Device Manager, click Driver Signing. The Driver Signing Options dialog box is displayed.
4. Select Ignore – Install all files, regardless of file signature.
5. Click OK twice.
You can now install the null modem driver.
Note: Before you start installing the null modem driver, make sure that the file "amr.inf" is stored on your PC.
1. In the Windows Start menu, select Settings → Control panel. The Control Panel appears.
2. Double click on the Phone and Modem icon. The Phone and Modem Options dialog box appears.
3. Under Modems, click Add... to start the modem installation sequence.
4. Select Don’t detect my modem; I will select it from a list. Click Next >.
5. Click Have disc...6. Select the path to where the file "amr.inf" is stored. Click
OK.
7. Select the Allgon Microwave Radio modem. Click Next >.
8. Select COM1 or equivalent serial port that you want to connect the modem to. Click Next >.
9. Click Finish.10. If the Modems Properties dialog box does not
automatically appear, double click on the Phone and Modem icon in the Control Panel.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
11. Select the Allgon Microwave Radio modem.
12. Click Properties. The Allgon Microwave Radio Properties dialog box appears.
13. Under General, select Maximum Port Speed = 115200 (other values are possible, refer to the Operation and Maintenance Manual (WLDM002)). Make sure that Wait for dial tone before dialling is unchecked.
14. Under Advanced, click Change Default Preferences.... The Allgon Microwave Radio Default Preferences dialog box appears.
15. Under General, select Flow Control = Hardware.16. Under Advanced, select Data bits = 8, Parity = None, Stop
bits = 1.
17. Click OK twice.18. Click OK.19. Restart your computer for the changes to take effect.
20. You have now installed the null modem driver. Proceed to section Configuring Dialling Up via Serial Port (Windows 2000) below.
M001EnC 71
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
72
‰ Configuring Dialling Up via Serial Port (Windows 2000)
The serial port that will be used as a connection must be configured for dialling up the radio terminal.1. In the Windows Start menu, select Settings → Network
and Dial-up connections. The Network and Dial-up connection panel appears.
2. Double click on the Make New Connection icon. The Network Connection Wizard dialog box appears. Click Next >.
3. Check Dial-up to private network. Click Next >.
4. Leave the Phone number box empty. If the program requires that you enter a telephone number, enter any random number. This is of no importance to the function of the radio terminal modem. Click Next >
5. Check For all users. Click Next >6. Enter DialUpAMR in the box "Type the name you want to
use for this connection".7. Click Finish.
8. In the Windows Start menu, select Settings → Network and Dial-up connections. Right-click on DialUpAMR, and select Properties. The DialUpAMR Properties dialog box appears.
9. Under General, make sure the Allgon Microwave Radio modem is chosen in the Dial using box.
10. Under Networking, check Internet Protocol (TCP/IP).11. Click Properties. The Internet Protocol (TCP/IP)
Properties dialog box appears.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
12. Check Use the following IP address and enter the IP address for your computer in the IP address box. If you want your computer to be allocated an IP address dynamically, check Obtain an IP address automatically.
13. If there is a DNS server in your network, check Use the following DNS server addresses and enter its IP address in the Preferred DNS server box. If you have no DNS server, check Obtain DNS server address automatically.
14. Click Advanced. The Advanced TCP/IP Settings dialog box appears.
15. Check Use default gateway on remote network.16. Click OK twice.17. Your PC is now set up for local management and may be
connected to a radio terminal. Proceed to section Terminal Access below.
M001EnC 73
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
74
Terminal Access
‰ Terminal Access via Text Terminal Application
Before connecting a PC to the radio terminal, make sure that the PC has been configured as described in the previous sections for Setting up the PC with Windows NT on page 63, or Setting up the PC with Windows 2000 on page 68. Then, do the following:1. Make sure the radio terminal is switched ON.
Connecting the PC to the radio terminal via a serial PC cable2. Connect the PC to the radio terminal according to the figure
above:
a) Serial port (COM1 or equivalent) of the PC.
b) Serial PC cable.
c) RS-232 port on the BBU marked LM/NMS 1.3. Start the terminal program (HyperTerminal or equivalent)
on your PC. If the program asks if you want to install a modem, select No.
4. Open the session SerialPortAMR.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
5. The terminal program window should now be active. Hold down the Enter key until the login dialog appears. The default settings are:
– Username: Level2
– Password: Kirk
Note: The Username and the Password are case sensitive.
‰ Configuring the Terminal for TCP/IP Access
To get access to the built-in web server containing the Allgon Microwave Radio configuration pages, the terminal must be configured for TCP/IP communication. After establishing terminal access via a text terminal application, do the following:1. Allocate an IP address to the serial port LM/NMS 1 of the
radio terminal by executing the command
setip 3 <ipaddress>
where <ipaddress> is the desired IP address.
2. Allocate a subnet mask to the serial port by executing the command
setnm 3 <subnetmask>
where <subnetmask> is the desired subnet mask (default = 255.255.255.0).
M001EnC 75
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
76
3. After you have changed the system settings according to step 9–10 above, you must restart the terminal for the changes to take effect. Execute the command
restart soft
and wait until the terminal is ready and idle again.
4. Log in and use the command
ipconfig
to verify that the commands in step 9–10 above were successfully executed. This command will return the current IP addresses for the ports of the radio terminal.
5. Use the command
logout
6. Exit the HyperTerminal program and close the connection.
7. Proceed to section Dialling Up via the Serial Port below.
‰ Dialling Up via the Serial Port
The procedure for dialling up the radio terminal via the serial port depends on which operating system you are using on your PC; choose the correct alternative below. Note that the file amr.inf must have been installed, as described in Installing Null Modem Driver (Windows NT) on page 65, or Installing Null Modem Driver (Windows 2000) on page 69 before you can dial up via the serial port.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
Windows NT
1. Double click on the Dial Up Networking icon located under the My computer icon on the desktop, or under My computer in the Explorer.
2. Double click on the DialUpAMR icon. A login dialog box appears.
3. Click OK.4. You have now established a local management connection
between your PC and the radio terminal. Proceed to section below.
Windows 2000
1. In the Windows Start menu, select Settings → Network and Dial-up connections → DialUpAMR. A login dialog box appears.
2. Click Dial.3. You have now established a local management connection
between your PC and the radio terminal. Proceed to section below.
M001EnC 77
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
78
Accessing the Radio Terminal Web Pages
‰ Accessing the Web Pages
1. Start the web browser on your PC/management equipment.2. Under Tools (IE 5.0), or Wiew (IE 4.0), select Internet
Options → Connection.
3. In the box Dial-up Settings, select DialUpAMR, and click OK.
4. In the URL address box marked "Location" (Netscape) or "Address" (Explorer), enter the name or the IP address of the radio terminal. The login dialog box appears.
5. Enter the default login, which is:
– Username: Level2
– Password: Kirk
Note: The Username and the Password are case sensitive.6. You will now automatically be transferred to the main page
of the radio terminal. Choose the web page that you want to access in the menus to the left of the web pages.
Note: The first time you access the web pages, you should change the default password settings. Do this on the web page "Access Level Configuration" (Terminal → Access Level).
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
Initial Radio Terminal Configuration
This section describes the minimum configuration you must perform to get the radio terminal up and running.
‰ Initial Radio Terminal Configuration
7. Supply the radio terminal with system information. Refer to section Editing System Information on page 81.
8. Configure the RF channel. Refer to section Configuring the RF Channel on page 82.
9. Configure the traffic channels. Refer to section Connecting the Traffic Channels on page 84.
10. If applicable, configure the Ethernet traffic interface. Refer to section Configuring Ethernet Traffic Ports on page 86.
11. Proceed to section Remote Management Connection on page 90. For daisy-chaining radio terminals, refer to section Interterminal Connection on page 100.
M001EnC 79
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
80
Traffic Routing in the Indoor Unit
Model for traffic channel connections
A radio terminal transmits all traffic channels connected to its RF side. You can connect the traffic channels from a TIU to the RF side of the same radio terminal. To let another radio terminal transmit them, you can cross-connect them to the RF side of a backplane partner.
You can cross-connect traffic channels over the hop, i.e. connect a traffic channel on a TIU port to an RF port with a different port number. This means that the traffic channel number for a traffic stream can be different from one end of the hop to the other. This can be useful in a repeater configuration where you want to drop a traffic channel on a certain traffic channel number. For example, you may want to drop a traffic channel on traffic channel number E1:17 to output it on a separate cable connected to the 9 pin D-SUB jack. To avoid confusion, it is recommended that you cross-connect all traffic channels at one end of the hop only.
BBU (1)
BBU (2)
RF Ports
RF Ports
Hop Cross-connection
Backplane Cross-connection
Straight-through Connection
TIU Ports
TIU Ports
Backplane
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
The traffic channel connections depend on the desired repeater and redundancy functionality. For further information on the traffic routing in the radio terminal, refer to the Operation and Maintenance Manual (WLDM002).
Note: You must configure the RF channel before you configure the traffic channels.
‰ Editing System Information
Select Terminal → Identification, and edit the following parameters:
Terminal ID: Enter an ID for the radio terminal.Terminal location:
Enter the name of the location for the radio terminal.
Contact: Enter name and means of contact for the system administrator or the department responsible for maintaining the radio terminal network.
Domain name: Enter a valid fully qualified domain name for the radio terminal. (The default hostname AMR must be changed if you are going to connect more than one radio terminal. Remember to define the new hostname in your network. You may also have to change the proxy settings in your web browser.)
M001EnC 81
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
82
‰ Configuring the RF Channel
Select Traffic → RF Channel and edit the following parameters:
Bandwidth Select a bandwidth value.RF frame format Select an RF frame format.RF channel no Enter the RF channel number.
Alternatively you may enter the TX frequency.
TX frequency Enter the transmitter frequency.
Alternatively you may enter the RF channel no.
Lock frequency to built-in channel plan
Select if the TX frequency should be locked to the built-in RF channel.
TX mute Select "Normal function".Output power Enter the desired output power
level (in steps of 0.1 dB).
≤19 dBm for 37–40 GHz, ≤20 dBm for 21–30 GHz.
Security code Enter the correct security code.
0–255; this number must be the same for the terminals at both ends of the hop.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
Expected RSL Enter the expected Received Signal Level (in steps of 0.1 dB).
When the RSL corresponds to the expected value entered here, the AGC voltage level on the RFU will be 3.5 V to indicate correct alignment of the antenna.
Use channel filter in RSL calculation
Select if the RSL should be calculated after bandpass filtering of the received signal.
Using channel filter will make the accuracy drop 3–4 dB. Thus, channel filter should only be used in case of interference from adjacent channels.
Submit all RF channel configurations to the database.
Submit RF channel configurations for a group of parameters to the database.
M001EnC 83
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
84
‰ Connecting the Traffic Channels
To connect all traffic channels straight through, without any cross-connecting, select Shortcuts → All straight through.
All traffic channels from the TIU side are then connected to the corresponding traffic channels on the RF side. They will all be transmitted by the radio terminal.
To cross-connect traffic channels, select Traffic → Traffic Channel and edit the following parameters:
TIU port Traffic channels from the TIU. These correspond to the traffic ports on the front of the terminal.
Terminal Select the radio terminal that you want to connect each traffic channel from the TIU to.
To connect radio terminals to the backplane, refer to the Operation and Maintenance Manual (WLDM002).
Port Select the traffic channel on a TIU or RF port that you want to connect each traffic channel from the TIU to.
RF port Traffic channels from the RF side, i.e. the traffic channels transmitted across the hop to the terminal.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
Terminal Select the radio terminal that you want to connect each traffic channel from the RF side to.
To connect radio terminals to the backplane, refer to the Operation and Maintenance Manual (WLDM002).
Port Select the traffic channel on a TIU or RF port that you want to connect each traffic channel from the RF side to.
M001EnC 85
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
86
‰ Configuring Ethernet Traffic Ports
Select Traffic → Ethernet TIU and edit the following parameters:
Maximum packet size
Select the maximum packet size for the ports.
• Individual port setting: The maximum packet size is determined by the "Packet Size" for each individual port below.
• 6 kB packet size: The maximum packet size will be 6 kB. This setting overrides the "Packet Size" for each individual port below.
VLAN mode Select VLAN mode for the ports.Maximum buffers allocated
Enter the maximum number of buffers that may be allocated to each port.1
XOFF threshold Enter the number of allocated buffers that must be exceeded to apply flow control to a port1.
XON threshold Enter the number of allocated buffers that must be passed below to remove flow control from a port1.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
Address lookup algorithm
Select MAC address lookup algorithm.
• Optimized for sequential MAC addresses.
• Optimized for random MAC addresses.
1. The actual number of buffers is truncated to the nearest lower multiple of 8.
Port no The Ethernet traffic ports on the front of the terminal.
Enabled Select if traffic transmission should be enabled on each port.
Duplex Select duplex mode for each port.
Half duplex/Full duplex/Auto-negotiate.
If you choose Auto-negotiate, the speed will be forced to Auto-negotiate.
Speed Select speed for each port.
10 Mbit/s, 100 Mbit/s, or Auto-negotiate.
If you choose Auto-negotiate, the duplex mode will be forced to Auto-negotiate.
Flow control Select if flow control should be used for each port.
No flow control/Flow control/Auto-negotiate.
M001EnC 87
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
88
Packet size Select packet size for each port (bytes).
• 1518: Used for most Ethernet types.
• 1536: Used for VLAN tagging.
This setting may be overridden by "Maximum packet size" above.
Port VLAN ID1 Enter a VLAN ID for each port.
Interval = 1-4095VLAN port mode1
Select the VLAN port mode with the desired forwarding criteria for the port.
• Access without tag: Used to transport a single LAN on the port. VLAN tags are removed.
• Access with tag: Used to transport a single LAN on the port. VLAN tags are retained.
• Trunk: Used to transport several LANs on the port. The VLAN list defines which LANs should be denied.
• Multi-access: Used to transport several LANs on the port. The VLAN list defines which LANs should be allowed.
Always use mode Access without tag when connecting to equipment that does not accept VLAN tagged frames, e.g. the Ethernet management interface.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
VLAN list2 Enter a list of VLAN IDs that should be denied (trunk), or allowed (multi-access) on the port.3
Separate the VLAN IDs with commas, e.g. 2,4,9. For series of VLAN IDs, put a minus sign between the lowest and highest VLAN ID, e.g. 3-22.
1. The parameter is only applicable if you have set the VLAN mode to port based VLAN.
2. The parameter is only applicable if you have set the VLAN mode to port based VLAN and the VLAN port mode to Trunk or Multi-access.
3. The maximum number of characters in the VLAN list is 255.
M001EnC 89
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
90
Remote Management Connection
Connect the radio terminal remotely according to one of the following alternatives:
• For set-up of a TCP/IP network on an Ethernet LAN, refer to section Connecting to Ethernet LAN below.
• For set-up of a TCP/IP network via a modem, refer to section Connecting via Modem on page 92.
• For set-up of a TCP/IP network via an ECC, refer to section Connecting via ECC on page 95.
‰ Connecting to Ethernet LAN
1. Allocate an IP address to the Ethernet port (10baseT/100BaseTX) of the radio terminal in one of the following ways:
– For set-up of a TCP/IP network on an Ethernet LAN using static IP addresses, allocate a static IP address, subnet mask and broadcast address to the Ethernet port. Refer to section Allocating Static IP Address on page 98.
– For set-up of a TCP/IP network on an Ethernet LAN using dynamic IP addresses, configure the Ethernet port to use dynamic IP addresses. Refer to section Allocating Dynamic IP Address on page 99.
For detailed information about static and dynamic allocation of IP addesses, refer to the Operation and Maintenance Manual (WLDM002)
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
2. Perform a soft restart of the radio terminal for the changes to take effect:
– Select Terminal → State Control and select Restart type = Soft.
– Wait until the radio terminal is in STANDBY state.3. Go to the web page "Address Configuration" (Network →
IP Addresses) to verify the changes above.
4. Go to the web page "Network Interface Configuration" (Network → Interfaces) and make sure that the status of the Ethernet port (10BaseT/100BaseTX) is set to "Up".
5. Exit the web browser and disconnect the serial PC cable between the local PC and the radio terminal.
6. Make sure the remote management equipment is connected to the Ethernet LAN network, or to another radio terminal connected to the Ethernet LAN network, and that it is set up to work properly in this environment. For further information, refer to the Operation and Maintenance Manual (WLDM002).
7. Connect the radio terminal to the network by connecting an UTP cable to the 10BaseT/100BaseTX port on the BBU.
M001EnC 91
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
92
‰ Connecting via Modem
1. Allocate an IP address to the serial port (MODEM/NMS 2) of the radio terminal in one of the following ways:
– For set-up of a TCP/IP network on a modem connection using static IP addresses, allocate a static IP address, subnet mask and broadcast address to the serial port (MODEM/NMS 2). Refer to section Allocating Static IP Address on page 98.
– For set-up of a TCP/IP network on a modem connection using dynamic IP addresses, configure the serial port (MODEM/NMS 2) to use dynamic IP addresses. Refer to section Allocating Dynamic IP Address on page 99.
2. Configure the serial port (MODEM/NMS 2) for modem connection by selecting Network → Serial Interfaces and editing the following parameters:
3. Configure the modem behaviour for the serial port (MODEM/NMS 2) by selecting Network → Serial Interfaces and editing the following parameters:
– Telephone number;
– Modem mode; and
Interface RS-232/2
Baudrate Select the baudrate to use.Usage Select the connection type "External
modem".
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
– Modem idle timeout.
4. Configure the modem AT commands for the serial port (MODEM/NMS 2) by selecting Network → Serial Interfaces and clicking Configure for the "Initialize sequence", "Dial sequence" or "Disconnect sequence". Edit the following parameters:
Command Edit AT commands for initializing, dialling or disconnecting the modem.
For the dial sequence, the telephone number will be automatically added after the last command provided that you have entered a value for "Telephone number" above
Response Enter the expected response to each AT command.
Leave empty if no response is expected.
Update the database with the new settings for the AT command.
Delete the AT command in the database.Add a new AT command, entered on the row "Add command", to the database.
M001EnC 93
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
94
5. Configure the modem security by selecting Network → Serial Interfaces and editing the following parameters:
– Authentication protocol (No authentication, PAP or CHAP);
– PAP user (if PAP is used);
– PAP password (if PAP is used);
– PAP password confirmation (if PAP is used);
– CHAP secret (if CHAP is used); and
– CHAP secret confirmation (if CHAP is used).
6. Perform a soft restart of the radio terminal for the changes to take effect:
– Select Terminal → State Control and select Restart type = Soft.
– Wait until the radio terminal is in STANDBY state.
7. Go to the web page "Address Configuration" (Network → IP Addresses) to verify the changes above.
8. Go to the web page "Network Interface Configuration" (Network → Interfaces) and make sure that the status of the serial port (MODEM/NMS 2) is set to "Up".
9. Exit the web browser and disconnect the serial PC cable between the local PC and the radio terminal.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
10. Make sure the remote management equipment is connected to a remote modem, and that it is set up to work properly in its environment. For further information, refer to the Operation and Maintenance Manual (WLDM002).
11. Connect the radio terminal to a modem by using the serial port (MODEM/NMS 2) on the BBU.
12. Proceed to section Antenna Alignment on page 103.
‰ Connecting via ECC
1. Allocate an IP address to the ECC port of the radio terminal in one of the following ways:
– For set-up of a TCP/IP network on a ECC connection using static IP addresses, allocate a static IP address, subnet mask and broadcast address to the ECC port. Refer to section Allocating Static IP Address on page 98.
– For set-up of a TCP/IP network on a ECC connection using dynamic IP addresses, configure the ECC port to use dynamic IP addresses. Refer to section Allocating Dynamic IP Address on page 99.
2. Configure the ECC port by selecting Network → ECC and editing the following parameters:
Port no Select the traffic port to use for the ECC.
Traffic ports available for an ECC are E1:1–17
M001EnC 95
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
96
Slot no Select the timeslot to use for the ECC.
0–31 (E1)
Use 7 bits Choose if 7 bit signalling should be used.
Yes: The 7 most significant bits will be used.
No: All 8 bits will be used.
Force connection
Choose if the ECC should override an AIS.
CRC active Select if the traffic channel that the ECC belongs to should use CRC.
If the incoming traffic uses CRC, the traffic channel should use CRC. This way, the radio terminal will recalculate the CRC after adding the ECC.
Service Indication that the radio terminal acts in Client/Server mode.
Forced connection status
Indication that the ECC overrides an AIS.
TX Status Indication that the ECC is synchronized in the outgoing direction.
RX Status Indication that the ECC is synchronized in the incoming direction.
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
3. Perform a soft restart of the radio terminal for the changes to take effect:
– Select Terminal → State Control and select Restart type = Soft.
– Wait until the radio terminal is in STANDBY state.4. Go to the web page "Address Configuration" (Network →
IP Addresses) to verify the changes above.
5. Go to the web page "Network Interface Configuration" (Network → Interfaces) and make sure that the status of the ECC port is set to "Up".
6. Exit the web browser and disconnect the serial PC cable between the local PC and the radio terminal.
7. Make sure the remote management equipment is connected to the ECC, and that it is set up to work properly in its environment. For further information, refer to the Operation and Maintenance Manual (WLDM002).
M001EnC 97
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
98
‰ Allocating Static IP Address
Select Network → IP Addresses and select the link static addresses. Edit the following parameters for the interface in question:
For further information on static IP addresses, refer to the Operation and Maintenance Manual (WLDM002).
Interface Management network interface.Address Enter the IP address for the network
interface.Subnet mask Enter the subnet mask for the
network interface.
Default = 255.255.255.0
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
‰ Allocating Dynamic IP Address
Select Network → IP Addresses and edit the following parameter for the interface in question:
Interface Management network interface.
Use DHCP Select if the interface should be allocated a dynamic IP address from a DHCP server.
No: DHCP will not be used.
Yes, send request on all interfaces: The DHCP request will be sent on all interfaces. Use this alternative if only one DHCP server is present in the network, and if you are not sure which path the DHCP request may follow to the DHCP server.
Yes, send request on this interface: The DHCP request will be sent on this interface only. Use this alternative if the DHCP server that you want to use is connected towards this interface, and you want to be sure that the DHCP request does not reach a DHCP server connected towards any of the other interfaces.
M001EnC 99
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
100
Interterminal Connection
Daisy-chaining Radio Terminals
Additional Equipment for Configuration
Table 29 Additional equipment for remote management, daisy-chaining
Equipment Description
Serial Cable For connection of two radio terminals via the serial interfaces.
• For an LM/NMS 1–MODEM/NMS 2 connection, use a straight-through serial cable with one 9 pin D-SUB plug (male) and one 9 pin D-SUB jack (female).
• For an LM/NMS 1–LM/NMS 1 connection, use a null modem cable with two 9 pin D-SUB plugs (male).
• For a MODEM/NMS 2–MODEM/NMS 2 connection, use a null modem cable with two 9 pin D-SUB jacks (female).
WLDM001EnC
Installation ManualChapter 5: Start-up and Configuration
WLD
‰ Daisy-chaining
1. Allocate an IP address to the serial port (LM/NMS 1 or MODEM/NMS 2) of the radio terminal in one of the following ways:
– For set-up of a TCP/IP network on a daisy chain using static IP addresses, allocate a static IP address, subnet mask and broadcast address to the serial port (LM/NMS 1 or MODEM/NMS 2). Refer to section Allocating Static IP Address on page 98.
– For set-up of a TCP/IP network on a daisy chain using dynamic IP addresses, configure the serial port (LM/NMS 1 or MODEM/NMS 2) to use dynamic IP addresses. Refer to section Allocating Dynamic IP Address on page 99.
2. Configure the serial port (LM/NMS 1 or MODEM/NMS 2) for connection to a radio terminal by selecting Network → Serial Interfaces and editing the following parameters:
3. Make sure the serial port (LM/NMS 1 or MODEM/NMS 2) on the radio terminal to connect to has been configured for connection to a radio terminal as well.
4. Perform a soft restart of the radio terminal for the changes to take effect:
Interface Baudrate Usage
RS 232/1 or RS 232/2
Select the baudrate to use.
Select the connection type "BBU via NULL modem".
M001EnC 101
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 5: Start-up and Configuration
102
– Select Terminal → State Control and select Restart type = Soft.
– Wait until the radio terminal is in STANDBY state.5. Go to the web page "Address Configuration" (Network →
IP Addresses) to verify the changes above.
6. Go to the web page "Network Interface Configuration" (Network → Interfaces) and make sure that the status of the serial port (LM/NMS 1 or MODEM/NMS 2) is set to "Up".
7. Exit the web browser and disconnect the serial PC cable between the local PC and the radio terminal.
8. Make sure the remote manager is connected to the management network, and that it is set up to work properly in its environment. For further information, refer to the Operation and Maintenance Manual (WLDM002).
9. Connect the radio terminal to the other radio terminal by using the serial port (LM/NMS 1 or MODEM/NMS 2) on the BBU.
– For an LM/NMS 1–MODEM/NMS 2 connection, use a straight-through serial cable with one 9 pin D-SUB plug and one 9 pin D-SUB jack.
– For an LM/NMS 1–LM/NMS 1 connection, use a null modem cable with two 9 pin D-SUB plugs.
– For a MODEM/NMS 2–MODEM/NMS 2 connection, use a null modem cable with two 9 pin D-SUB jacks.
10. Proceed to section Antenna Alignment on page 103.
WLDM001EnC
Installation ManualChapter 6: Antenna Alignment
WLD
Chapter 6: Antenna Alignment
Tools Required for Antenna Alignment
• 17 mm torque wrench
• Voltmeter (0–5V DC) with BNC adapter (the AGC contact on the RFU is of BNC socket type).
Preparations1. Check that all relevant instructions in the preceding
sections of this manual are completed for both installation sites before you start aligning the antennas.
2. Arrange for speech communication between the installation sites if possible. This will make it easier to align the antennas correctly.
Alignment Procedure
When aligning the antennas, the AGC port on the RFU (BNC connector) is used to indicate the Received Signal Level (RSL). Use a standard multimeter with a BNC adapter to measure the AGC voltage. The AGC voltage is somewhere in the range 0–5V DC.
The AGC voltage from the BBU is updated every 0.2 sec. So, when the antenna has been moved, the resulting AGC voltage may be slightly delayed. A digital voltmeter also has a slight delay. This means that you should allow 0.5 - 1 sec to pass before checking the AGC voltage, after moving the antenna.
M001EnC 103
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 6: Antenna Alignment
104
Note: The alignment procedure should be performed for one antenna at a time. If the initial alignment error is large, however, you may need to begin by moving both antennas to achieve contact.
1. Connect the voltmeter to the AGC port on the RFU.
The voltmeter will always show a value of at least 0.5V if the radio terminal is working correctly.
If the antenna is receiving an unknown signal, or a signal from a radio terminal which has the wrong security code, the voltmeter will show an oscillating value.
2. Maximize the voltmeter value by using the azimuth and elevation screws to adjust the antenna. The maximum possible adjustment is ±15 degrees in azimuth and ±20 degrees in elevation.
Note: If the alignment error is more than approximately 4 degrees, there is a risk that the maximum AGC voltage that you have found is for a side lobe. The maximum value of the AGC voltage is lower for a side lobe than for the main lobe.
WLDM001EnC
Installation ManualChapter 6: Antenna Alignment
WLD
– Azimuth fine tuningLoosen the two bolts (A) 1/2 turn. Use the azimuth screw (B) to adjust the antenna.
– Elevation fine tuningLoosen the three bolts (C) 1/2 turn. Use the elevation screw (D) to adjust the antenna.
Note: Do not loosen the bolts too much. There should be a slight friction when aligning the antenna.
3. Use the torque wrench to secure the antenna position by tightening the bolts for both azimuth and elevation. These are indicated in the figure above (A and C).
Note: The torque should be 35 Nm ± 10% when tightening the screws. The azimuth and elevation screws must not be touched after the locking screws have been tightened.
4. Check the RSL on the web page "RF Channel Status" (Status → RF Channel Status) of the Indoor Unit and record the value.
M001EnC 105
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 7: Installation Verification and Test
106
Chapter 7: Installation Verification and Test
Checking RF Channel Status1. Make sure that all relevant instructions in the preceding
sections have been performed for both installation sites.2. Make sure that your PC is connected to one of the radio
terminals in the hop according to section Local Management Connection on page 63.
3. Follow the instructions in section Accessing the Web Pages on page 78 to access the web pages for one of the radio terminals.
4. Access the web page "RF Channel Status" (Status → RF Channel Status).
5. Check that all status values are in accordance with the table below:
Parameter Status
RF Path Availability AvailableReceived Signal Level Compare this value with
the expected RSL.Security Code OKModem Phase Lock OKModem Bit Synchronization
OK
WLDM001EnC
Installation ManualChapter 7: Installation Verification and Test
WLD
6. Repeat step 3–5 above for the radio terminal at the far end of the hop.
MUX Bit Synchronization
OK
Last Second Errored NoLast Second Severely Errored
No
Background Block Error during last second
No
Errored Second Rate 0%Severely Errored Second Rate
0%
Background Block Error Rate
0%
RF Present YesRF Measured Power Compare this value with
the configured TX Output Power.
Parameter Status
M001EnC 107
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 8: Maintenance
108
Chapter 8: Maintenance
Replacing the Baseband Unit
Required Tools
• Pozidrive screwdriver PZ2 and PZ3.
‰ Removing the BBU
For details about the Indoor equipment, refer to Indoor Installation on page 18.
Note: Removing the BBU will interrupt all traffic on the radio terminal.
1. Disconnect the power cable.2. Undo the two screws on the front of the TIU, and remove
the TIU.
3. Disconnect the remaining cables on the front of the BBU.If there is a risk of confusing the cables when reconnecting them, you should label the cables before disconnecting.
4. Disconnect the grounding cable (depending on the mounting solution).
5. Remove the BBU from the rack (depending on the mounting solution). Use a Pozidrive screwdriver PZ3.
6. Remove the mounting rail from the BBU (magazine mounting only). Use a Pozidrive screwdriver PZ2.
WLDM001EnC
Installation ManualChapter 8: Maintenance
WLD
‰ Mounting the New BBU
For details about the Indoor equipment, refer to Indoor Installation on page 18.
1. If necessary, move the brackets to fit in the rack set-up. Use a Pozidrive screwdriver PZ2.
2. Mount the mounting rail on the BBU (magazine mounting only). Use a Pozidrive screwdriver PZ2.
3. Mount the BBU in the rack (depending on the mounting solution). Use a Pozidrive screwdriver PZ3.
Note: Mount the magazine in the rack before you remove the transport safety panels.
4. Connect the grounding cable (depending on the mounting solution).
5. Connect the cables to the front of the BBU (except the power cable).
6. Mount the TIU, and tighten the two screws on the front of the TIU.
7. Connect the power cable.8. Download software, option download BBU. For details on
Software Download, refer to the Operation and Maintenance Manual (WLDM002). Download the configuration backup (refer to section Configuration
CAUTION!
When mounting the TIU in the BBU, the two screws must be fastened by hand! Do not use any tools or excessive force!
M001EnC 109
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 8: Maintenance
110
Backup below) and, if required, perform additional configuration of MIB parameters not included in the configuration backup.
Configuration Backup
A backup of the essential configuration data in the MIB in the BBU is stored in a database in the RFU. You can retrieve this data if the data in the MIB has been damaged, or if the BBU has been replaced. Further, you can control whether the backup in the RFU should be updated manually or automatically.
‰ Storing and Retrieving Configuration Backup
Logon to the web pages (refer to and select Terminal → Configuration Backup, and change and view the following parameters:
Mode Select storage mode:
• No storage: It is not possible to update or retrieve the configuration backup.
• Manual storage: It is possible to update the configuration backup manually. It is also possible to retrieve the configuration backup.
• Auto storage: Whenever a change occurs in the MIB, the configuration backup will be updated automatically. It is possible to retrieve the configuration backup.
WLDM001EnC
Installation ManualChapter 8: Maintenance
WLD
Action Select to manually update or retrieve the configuration backup:
• None: No configuration backup will be updated or retrieved.
• Retrieve from RFU: The current MIB data will be replaced with the configuration backup.
• Store image in RFU: The configuration backup will be updated with the current MIB data.
Only applicable for storage modes "Manual storage" and "Auto storage".
Status Indicates status of the configuration backup in the RFU.
• Configuration backup OK: The configuration backup corresponds to the current MIB data in the BBU.
• Working: The configuration backup is being updated.
• Data stored by other BBU: The configuration backup has been stored by another BBU than the current one.
• Invalid data in RFU: No configuration backup has been stored, the configuration backup has not been updated since last MIB change, or the configuration backup is corrupt. It is not possible to retrieve any configuration backup.
M001EnC 111
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 9: 1+1 Installation and Configuration
112
Chapter 9: 1+1 Installation and Configuration
1+1 Installation Indoor Equipment
The 1+1 installation requires two Indoor Units, installed in a common backplane. For equipment details, refer to Indoor Equipment on page 19. For installation, see Mounting the Indoor Unit on page 28 and Common Backplane Mounting In Magazine for 19" Rack on page 30.
The two Indoor Units are connected with each other using a BBU Redundancy Partner Detection Cable. The detection cable is connected to the external I/O port on each BBU.
Table 30 Additional equipment for 1+1 installation Part Part Number Qty.
Baseband Unit Redundancy Partner Detection Cable, 0.4 m
WUKA113/004 1
WLDM001EnC
Installation ManualChapter 9: 1+1 Installation and Configuration
WLD
1+1 Installation Outdoor Equipment
For protected radio terminals using two RFUs, but only one antenna unit, the antenna unit and the RFUs are separately mounted.
1+1 installation, separately mounted
Note: It is also possible to have a 1+1 installation consisting of two complete hops. This requires two complete in- and outdoor units on each side of the hop. The two
M001EnC 113
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 9: 1+1 Installation and Configuration
114
Indoor Units, on each side, are connected using a common backplane and a BBU Redundancy Partner Detection Cable.
Table 31 Outdoor Equipment for 1+1 installation (separate mounting)
Pos. Part Part Number Qty.
1 Radio Frequency Unit (RFU)
WAAAxxxyy/zz 2
2 Antenna Unit (including Mast Mounting Bracket1)
1. Fits a mast of diameter 50 to 115 mm (2 to 4.5").
WAAFxxxyy/zz 1
3 Antenna Interface WMDAxxxyy 14
a)
b)
Power Splitter Kit, consisting of
RF Power Splitter
RF Interface
WMDExxxyy/zz
WMDRxxxyy
1
1
25 RFU Mast Mounting
BracketWMDFxxx 1
6 Flexible Waveguide WPUA015xx/yyy 1
WLDM001EnC
Installation ManualChapter 9: 1+1 Installation and Configuration
WLD
Polarization in Separately Mounted Installations
In a separately mounted installation, the polarization of the radio signal is determined by the position of the waveguide port on the Antenna Interface, not by the position of the RFUs.
Note: The position of the waveguide port is opposite to the position of the handles of the Antenna Interface. This means, that when the polarization is horizontal, the handles are in a vertical position, and vice versa.
Horizontal polarization in a separately mounted installation.
Vertical polarization in a separately mounted installation.
M001EnC 115
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 9: 1+1 Installation and Configuration
116
Installing a Separately Mounted 1+1 Installation
‰ Installing a Separately Mounted 1+1 Installation
1. Mount the the Antenna Interface on the Antenna Unit. Be careful to choose the correct polarization. The waveguide port on the Antenna Interface indicates the polarization, see Polarization in Separately Mounted Installations on page 115.
2. Fasten the Antenna Mast Mounting Bracket. For instructions, refer to Fastening the Mast Mounting Bracket on page 49.
3. Choose left or right side antenna mounting. For instructions, refer to Choosing Left or Right Side Antenna Mounting on page 48.
4. Mount the Antenna Unit/Antenna Interface on the Mast Mounting Bracket. This procedure is identical to the procedure of mounting an Antenna/RFU in an ordinary installation. For instructions, refer to Mounting the Antenna/RF Unit on the Mast Mounting Bracket on page 51.
5. Fasten the RFU Mast Mounting Bracket onto the mast. Make sure that the distance between the RFU Mast Mounting Bracket and the Antenna Unit does not exceed the length of the Flexible Waveguide.
6. Mount the two RFUs on the two RF Interfaces in the Power Splitter kit. The procedure of mounting an RFU on an RF Interface is identical to the procedure of mounting the RFU on the Antenna Unit in an ordinary installation. For instructions, see Mounting the RF Unit on the Antenna Unit on page 46.
WLDM001EnC
Installation ManualChapter 9: 1+1 Installation and Configuration
WLD
Note: It is also possible to mount the RFUs on the RF Interfaces when the Power splitter is already hooked onto the Mast Mounting Bracket.
7. Hook the Power Splitter Kit onto the RFU Mast Mounting Bracket, and fasten the bolts.
Note: To be able to attach the Power Splitter Kit properly, the bolts must be located in an outward position.
8. Connect the Flexible Waveguide to the port on the back of the Antenna Interface and to the port on the Power Splitter. Be careful to fit the Flexible Waveguide correctly onto the port on the Antenna Interface.
M001EnC 117
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 9: 1+1 Installation and Configuration
118
Redundancy Configuration
The radio terminals working in a redundancy configuration must be able to communicate with each other via the management network.
‰ Configuring Redundancy
Click on Terminal → Redundancy and set the following parameters:
Redundancy function
Select the type of redundancy function.
• No redundancy.
• 1+1 protection
Redundancy state
Select if the terminal should act as active or standby terminal.
• Standby: The radio terminal acts as standby terminal. The redundancy partner must be set as active terminal.
• Active: The radio terminal acts as active terminal. The redundancy partner must be set as standby terminal.
If you change the redundancy state on one terminal when the redundancy function is up and running, the state of the redundancy partner will be forced to the opposite state.
WLDM001EnC
Installation ManualChapter 9: 1+1 Installation and Configuration
WLD
Switch mode Select how to switch between active and standby state.
• On command only: You must manually change the redundancy states for the radio terminals when a failure occurs.
• Mutual agreement: When an event configured to trigger a switch occurs in one of the radio terminals, the terminal will verify with the other terminal that the criteria for switching are fulfilled before changing the redundancy states for the terminals.
• Autonomously: When an event configured to trigger a switch occurs in one of the radio terminals, the terminal will verify itself that the criteria for switching are fulfilled before autonomously changing the redundancy states for both terminals.
Time after switch during which a reverse switch is inhibited
Enter the time (seconds) after a switch during which the redundancy state can not be switched back.
The inhibition time prevents an active alarm from forcing recurrent redundancy state switches. It is only applicable for the switch modes "Mutual agreement" and "Autonomously".
Max. = 65535
M001EnC 119
Installation ManualInstallation ManualInstallation ManualInstallation ManualChapter 9: 1+1 Installation and Configuration
120
Traffic Channels in a 1+1 Configuration
For a radio terminal used in a 1+1 protected configuration, you must connect the traffic channels straight through from the TIU to the RF side. The two radio terminals used in the redundancy configuration have a combined traffic capacity corresponding to one radio terminal, i.e. you can only connect each traffic channel in one of the radio terminals, not both. Only those traffic channels not already connected in the redundancy partner are available for connection in the other radio terminal. The Cross-connect function will automatically route the traffic channels from the standby terminal to the active terminal, so that all traffic channels are transmitted by the active terminal.
Redundancy partner position
Select the backplane partner that should work together with the radio terminal in the redundancy configuration.
It is possible to select backplane positions regardless of whether a radio terminal is present or not. It is not possible to select the backplane position for this terminal, or to select backplane partners already part of another redundancy configuration.
WLDM001EnC
Installation Manual Index
WLD
IndexNumerics1 ft. antenna .............................. 151+1 Installation ...................... 112
Indoor Equipment.............. 112installation of ..................... 116Outdoor Equipment ........... 113polarization ........................ 115
1+1 SolutionAntenna Interface .............. 114Detection Cable ................. 112Flexible Waveguide .......... 114indoor equipment............... 112outdoor equipment............. 113Power Splitter Kit .............. 114redundancy configuration . 118RF Interface ....................... 114RFU Mast Mount. Bracket 114traffic channels .................. 120
17 x E1 Interfaces .................... 2619" rack
Installation Kit for ............... 19mounting the Indoor Unit in 29
2 ft. antenna .............................. 1526 pin D-SUB connector ......... 232U Magazine ............................ 20
Installation Kit for ............... 20space requirements .............. 11
6U Magazine ............................ 20Installation Kit for ............... 20space requirements .............. 11
9 pin D-SUB connectormodem ..................................22PC .........................................22
Aaccessories
indoor....................................20product numbers.....................6
Active ......................................118ACTIVE LED ...........................60AGC Cable................................43AGC port.................................103
contact type ........................103AGC voltage ................... 103–104ALARM LED ...........................61alignment.................................103
error ....................................104Allocating..................................98amr.inf ............................58, 65, 70Antenna Interface ...................114Antenna Unit.............................42
1 ft.........................................152 ft.........................................15alignment ............................103integrating with RFU ...........46left or right side mounting ...48mounting......................... 15, 51moving coaxial connector....44product numbers.....................6
Antenna/RF Unitgrounding .............................52left or right side mounting ...48
M001EnC 121
Installation ManualInstallation ManualInstallation ManualInstallation Manual IndexIndexIndexIndex
122
lifting ....................................47mounting ..............................51recommended mounting ......49
AT commands ..........................93azimuth
fine tuning ..........................105screw ..................................104
Bbackground block error ..........107background block error rate ...107balanced interface.....................26
connector mounting .............33bandwidth .................................82Baseband Unit ..........................19
product numbers ....................6BBU, see Baseband Unitberyllium oxide ..........................9BNC adapter ...........................103brackets .....................................29
Ccaptive nut
magazine ..............................20rack mount ...........................19
CHAP........................................94configuration
local management ................63radio terminal .......................79remote management.............90
configuration backupretrieving ............................110
storing ................................ 110connecting the power cable ..... 61connector
26 pin D-SUB for ext. I/O... 3737 pin D-SUB for traffic ..... 349 pin D-SUB for traffic ....... 35DC power........................19, 38mounting .............................. 33N type................................... 52
contact person .......................... 81control panel............................. 22Converter cable
SMZ-BNC ........................... 21copper braid for ........................ 13cross connect ............................ 80
Ddaisy-chaining
connection set-up............... 101equipment .......................... 100
DC connector ........................... 23Dial Up Networking
software................................ 57Windows 2000..................... 77Windows NT ....................... 77
dialling upconfiguration...................66, 72serial port ........................76–77
documentation ............................ 5domain name ............................ 81D-SUB connector
26 pin for external I/O....23, 37
WLDM001EnC
Installation Manual Index
WLD
37 pin for traffic channel..... 349 pin for modem .................. 229 pin for OH channel........... 369 pin for PC.......................... 229 pin for traffic channel....... 35DC power............................. 38
dynamic IP addresses............... 99
EE3 + E1 interface ..................... 25ECC connection set-up ............ 95electrical safety ........................ 10electromagnetic interference
indoor ................................... 13outdoor ................................. 17
elevationfine tuning .......................... 105screw .................................. 104
EMCindoor ................................... 13outdoor ................................. 17
environmentindoor requirements ............ 14outdoor requirements .......... 17
errored second ........................ 107errored second rate ................. 107Ethernet
DTE...................................... 23Ethernet + E1 Interfaces .......... 27Ethernet for management
cable ..................................... 58connection set-up................. 90
interfaces ..............................23Ethernet TIU
configuration ........................86connectors, mounting...........36duplex mode .........................87enable....................................87flow control ..........................87MAC address lookup ...........87packet size ...................... 86, 88speed .....................................87VLAN ...................................88
ETS 300 019 ....................... 14, 17ETS 300 385 ....................... 13, 17ETSI rack mounting kit ............21external I/O connector ..............37external protection circuits .......12
FFlat Copper Braid
BBU grounding ....................13flat copper braid
BBU grounding ....................31Flexible Waveguide ................114
Ggrounding
Antenna/RF Unit ..................52copper braid for ....................31indoor equipment .................13Indoor Unit ..................... 22, 31M6 lug for....................... 13, 31outdoor equipment ...............16
M001EnC 123
Installation ManualInstallation ManualInstallation ManualInstallation Manual IndexIndexIndexIndex
124
radio cable ...................... 17, 53requirements.........................10
Hhorizontal polarization ..... 44, 115hostname ...................................81humidity
indoor ...................................14outdoor .................................17
HyperTerminal ................... 55, 57
II/O port......................................23impedance converter cable
ITU 1x2, 9 pin D-SUB ........21ITU 8x2, 37 pin D-SUB ......21
indooraccessories............................20equipment.............................19requirements.........................11
indoor radio cable.....................39Indoor Unit ...............................19
EMC .....................................13grounding ....................... 13, 31installation............................18installing the cables for........33mounting ..............................28mounting in 19" rack ...........29mounting in magazine .........30numbering in magazine .......31space requirements ..............11
initial configuration ..................79
installationindoor ................................... 18outdoor ................................. 41verification......................... 106
Installation Kitfor 19" rack .......................... 19for 2U Magazine.................. 20for 6U Magazine.................. 20
Installation Manual .................... 5interfaces
17 x E1 ................................. 26co-directional ....................... 36E3 + E1 ................................ 25Ethernet + E1 ....................... 27
internal protection circuits ....... 12Interterminal Connection ....... 100IP addresses
allocation ............................. 98dynamic................................ 99static ..................................... 98
ITU Impedance Conv. Cable... 21ITU-T G.703 .......................24, 36
JJumper Cable to Mast Cable ... 19
LLAN .......................................... 58LEDs......................................... 22
blinking pattern.................... 60lightning protection.............49, 53LM/NMS1 port ........................ 22
WLDM001EnC
Installation Manual Index
WLD
local management ...............63–77equipment ............................ 57
locking screw ........................... 47login .......................................... 78
MM10 screws .............................. 48M6 grounding lug ......... 13, 22, 31magazine
2U......................................... 202U Installation Kit ............... 206U......................................... 206U Installation Kit ............... 20mounting of.......................... 30Mounting Rail for ...........20–21Mounting Rail Screw for20–21mounting the Indoor Unit in 30numbering of Indoor Units.. 31space requirements .............. 11
main lobe ................................ 104management
direct connection, static....... 75ECC connection................... 95Ethernet connection............. 90local.................................63–77modem connection .........92, 98remote .................................. 90
Mast Mounting Bracket ........... 42fastening to mast.................. 49
mast requirements .................... 16mast stability ............................ 16Metral connector ...................... 23
modem.......................................58AT commands ......................93authentication .......................94bit synchronization status ..106cable......................................59connection set-up .................92dial sequence ........................93disconnect sequence.............93driver for null modem .... 65, 69idle timeout...........................93initialize sequence ................93mode .....................................92telephone number .................92
MODEM/NMS2 port................22modular connector ....................23moisture protection ...................46mounting pole diameter............16Mounting Rail ..................... 20–21
Screw .............................. 20–21muting the TX ...........................82MUX
bit synchronization status ..107
NN connector ...............................52null modem driver
Windows 2000 .....................69Windows NT ........................65
OOH channel connector
9 pin D-SUB for OH ............36
M001EnC 125
Installation ManualInstallation ManualInstallation ManualInstallation Manual IndexIndexIndexIndex
126
operating system for PC ...........57Operation and Maintenance .......5operational modes ....................61operational states ......................60outdoor
EMC .....................................17equipment.............................42installation............................41requirements.........................15
Outdoor Accessories ................43AGC Cable...........................43Cold Shrink Weatherproofing
Kit ....................................53for grounding .......................52Grounding Kit ......................52
outdoor radio cablegrounding .............................53installation............................52maximum length ..................52
output power .............................82measured ............................107
PPAP ...........................................94password ...................................78
changing ...............................78PC
cable .....................................58connection ............................74serial port configuration 63, 68setting up ........................ 63, 68
phase lock
status for Baseband Unit ... 106polarization
checking ............................... 47choosing ............................... 44in separately mounted installa-
tions ............................... 115power
cable ................................10, 39consumption ........................ 12DC connector............ 19, 23, 38indoor requirements ............ 12outdoor requirements .......... 16output level configuration ... 82supply..............................12, 61
Power Splitter Kit .................. 114PPP network
dialling up .......................76–77dialling up configuration 66, 72set-up of ..........................75–77
Product List ................................ 5product numbers
accessories ........................6, 20Antenna Unit ....................6, 41Baseband Unit ..................6, 19Radio Frequency Unit ......6, 41Traffic Interface Unit . 6, 25–27
product range.............................. 6protected radio terminals ....... 112protection circuits..................... 12
RRack Mount Captive Nut ....19–20
WLDM001EnC
Installation Manual Index
WLD
Rack Mount Screw..............19–20radio cable
grounding ........................17, 53indoor mounting .................. 39maximum length.................. 52outdoor mounting ................ 52
Radio Frequency Unit.............. 42BBU connection status ...... 107integrate with Antenna Unit 46mounting .............................. 15product numbers .................... 6
redundancy configuration ...... 118Redundancy Partner Detection
Cable .................................. 112remote management ................. 90
equipment ............... 58–59, 100requirements
indoor ................................... 11indoor environment ............. 14indoor power........................ 12indoor space ......................... 11mast ...................................... 16outdoor ................................. 15outdoor environment ........... 17outdoor power...................... 16outdoor space....................... 15safety ...................................... 8site .......................................... 8
RF channelavailability ......................... 106configuration........................ 82measured power................. 107
number ..................................82status ...................................106
RF frame format .......................82RF Interface ............................114RF port ......................................84RFU Mast Mounting Bracket.114RFU, see Radio Frequency UnitRG213 cable .............................52RG214 cable .............................52RG400 cable .............................39RJ-45 connector ........................23router .........................................59RS-232
DCE ......................................22DTE ......................................22
RSL .........................................103checking..............................105expected ................................83status ...................................106
Ssafety
devices ....................................9electrical ...............................10precautions .............................8requirements ...........................8warnings .................................8
screwazimuth ...............................104elevation .............................104locking ..................................47magazine...............................20
M001EnC 127
Installation ManualInstallation ManualInstallation ManualInstallation Manual IndexIndexIndexIndex
128
mounting rail.................. 20–21rack mount ...........................19
security code ...........................104configuration ........................82status...................................106
serial portbaudrate ........................ 92, 101connection type ............ 92, 101dialling up ...................... 76–77dialling up configuration 66, 72modem connection......... 92, 98PC configuration ............ 63, 68PC connection, static ...........75
severely errored second..........107severely errored second rate ..107side lobe ..................................104site requirements ........................8SMZ-BNC Converter Cable ....21Sofix connector ........................23space requirements
indoor ...................................11outdoor .................................15
Standby ...................................118start-up and configuration ........55
equipment for .......................57static IP address ........................98
allocating to serial port ........75subnet mask allocation .............98surge arrester ...................... 39, 53switching
OFF ......................................62system information config. ......81
TTCP/IP network
set-up.................... 90, 92, 95, 98Technical Description ................ 5temperature
indoor ................................... 14outdoor ................................. 17
terminalID ......................................... 81location ................................ 81
TEST LED ............................... 60text terminal ............................. 57TIU port .................................... 84TIU, see Traffic Interface UnitTNC connector ......................... 22tools
for indoor installation .......... 18for outdoor installation........ 41
torque wrench....................41, 103traffic channels ......................... 84
connectors .......................34–35in 1+1 solution ................... 120
Traffic Interface Unit ..........19, 2417 x E1 ................................. 26balanced, cables for ............. 34balanced, connecting ........... 33E3 + E1 ................................ 25Ethernet + E1 ....................... 27Ethernet, connecting............ 36mounting .............................. 24product numbers .................... 6
traffic interfaces ....................... 24
WLDM001EnC
Installation Manual Index
WLD
traffic routing ........................... 80transients
preventing transmission of .. 62transmitter
frequency ............................. 82muting .................................. 82output power ........................ 82
TX/RX signal definition .......... 33
Uunbalanced interface ................ 25username................................... 78UTP cable ................................. 58
Vvertical polarization ..........44, 115VLAN ....................................... 88voltage
hazards ................................. 10supply ................................... 12
voltmeter..........................103–104
WWARNING LED ..................... 60web browser ............................. 57web pages
accessing .............................. 78choosing ............................... 78Ethernet TIU configuration. 86redundancy configuration . 118RF channel configuration.... 82
RF path status .....................106system information config. ..81traffic channels .....................84
Windows 2000dialling up configuration......72null modem driver ................69serial port configuration.......68
Windows NTdialling up configuration......66null modem driver ................65serial port configuration.......63
M001EnC 129
Installation ManualInstallation ManualInstallation ManualInstallation Manual IndexIndexIndexIndex
130
WLDM001EnC