Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
1
INSTALLATION INSTRUCTIONS: HORIZONTAL WALL BED HARDWARE KIT WITH FRAME
*Our more compact model for shipping.
Rockler Woodworking and Hardware 4365 Willow Drive, Medina, MN 55340
MODEL CODES:50479 (Twin horizontal wall bed)53155 (Double horizontal wall bed)58262 (Queen horizontal wall bed)
1-800-279-4441
2
A1 Head bar of the frame (with bearings) x1 x1 x1
A2 Foot bar of the frame x1 x1 x1
B Center frame support with slat holes x2 x2 x2
C Center frame supports x4 x4 x4
D Long center frame support x1 x1 x1
E Left and right frame bars x2 x2 x2
F Flat bars x2 x2 x2
G Pistons (non locking)Single: 90kg, Double: 90kg, Queen: 110kg x2 x2 x2
H Mattress Supports x2 x2 x2
I Mounting plates (left and right) x2 x2 x2
J Saddle locking plates x2 x2 x2
K Brackets to attach wall bed to wall x3 x3 x3
L Door brackets x8 x16 x16
M Legs (left and right) x2 x2 x2
N Tube (for attaching legs) x1 x1 x1
O Slats x36 x36 x38
P Slat caps x36 x36 x38
Q Double slat caps x18 x18 x19
HARDWARE
3
R Wrench x1 x1 x1
S1 Allen Key 4mm x1 x1 x1
S2 Allen Key 5mm x1 x1 x1
T Threaded inserts x16 x16 x16
U M8 x 16mm Screws x16 x16 x16
V #10 x 55mm Screws (Step 12) x26 x28 x28
W #8 x 15mm Screws (Steps 11-12) x36 x52 x52
X #10 x 15mm Screws x6 x6 x6
Y #10 x 30mm Screws x6 x6 x6
Z M5 x 15mm Screws x2 x2 x2
AA M6 x 30mm Bolts x4 x4 x4
BB M8x 50mm Bolts x22 x22 x22
CC Washers x12 x12 x12
DD Nylon Washers (for pivoting legs) x4 x4 x4
EE M5 Nuts (for saddle locks) x2 x2 x2
FF M8 Locking nuts x28 x28 x28
GG Temporary stoppers x2 x2 x2
4
Overall Cabinet Dimensions
* Suggested dimensions
Cabinet Parts Dimension Guide
D D C
C C C C
C C C C
C
5
3 18 "
6 1516 "
13
7 8"
17
3 4"
9 716 "
11
7 16"
61 8
" 7
3 4"
21 2
" 2
1 2"
11
7 16"
DRILLING GUIDE
FrontBack
Bottom
All measurements are for 3/4’’ thick board.
The holes should be 3/8” in diameter and 1/2” deep for threaded inserts.
*See full sized template in product box.
6
Right side
Front
Front
Left side
Bottom
INSTALLING THE MOUNTING BRACKETS1
U + T
U
I
T
I
Wood
ASSEMBLING THE CABINET2
* See guide on page 4 for suggested cabinet dimensions.
x16
x16
x2
S2
7
ASSEMBLING THE FRAME4
3 SECURING TO THE WALL
* Professional installation recommended.
* Needs to be secured into at least two wood or metal studs.
4.1Insert E into A1 and A2.
E
X=Y=CC=K=
x6x6x12x3
A1=
E= x2
These tabs should be flat on the ground.
x1
* Nylon wall anchors are NOT recommended
X
Y
A2
A1
A2= x1
Brackets can be installed on the inside or on the top of the cabinet.
8
4.2Attach D to A1 and A2 with BB and FF.
D
4.3Attach F and B to the inside of E, then attach the B supports to both sides of D.
FF= x4
BB= x4
FF= x6
BB= x6
D= x1
B=
F=
x2
x2
F
FBB
DE
E
These tabs should be flat on the ground.Flat bar “F”
9
4.4Bolt both ends of the supports C to the frame assembly.
FF= x12
BB= x12
5 INSTALLING THE SLATS
P
O P
QO
O
Q Place P on one end of each slat. Attach two slats together with Q.
Insert P and Q into their designated holes along the frame. Insert all of the slats except for the first and last rows of slats. Please see next page to see which slats to skip.
x32
x32
x16
*If necessary, use a rubber mallet to secure the slats into the frame.
C= x4
C
C
C
C
x34
x34
x17
10
6 ATTACHING THE PISTONS TO THE FRAME
FF= x2
Secure the longer metal ends of the pistons to the frame.
G= x2
FF
This end
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
For each bed size, do not insert the rows of slats on both ends of the frame.
Example below works for both single and double. Queen has 19 rows of slats
11
Place the bearing into the saddle on the mounting bracket. Secure the bearing in place with:
INSTALLING THE FRAME ONTO THE MOUNTING BRACKETS
Z
J
EE
x2
x2
x2
7
12
Tilt the frame inside past the edge of the cabinet to install the pistons on the mounting brackets.
INSTALLING THE PISTONS TO THE CABINET
FF x2
8
9 INSTALLING THE LEGS
FF
DD
NM
x2
x4
Do not overtighten.
Install tube to both legs.
M
9.1
9.3
AA
S1
x4
AA
AA
Install the temporary stoppers GG onto the top corners of the bed cabinet.
GG x2
Secure the legs to the bed frame.9.2
13
10 INSTALLING THE DOOR BRACKETS
The door brackets must point downward. Install the door brackets in alignment with the support bars on the bed frame.
Top
Bottom
11
* Install the handle on the other side of the door during this step. Decorative handle not included. Handle should be mounted at a height to comfortably allow the user to pull the bed down (approximately 1/3 of the way down from the top of the door).
9 3/16”
35 7/16”
6” 6”
Measurements (right) are for the placement of this hole on the backside of the doors.
INSTALLING THE DOORS
Hook the door brackets onto the frame and push down until they are firmly in place. Center the doors on the frame.
11.1
9 3/16”
41 7/16”
Twin: 1 door
Double/Queen: 4 doors
L
W
x8
x16
x16
x32
15”
9 3/16”
19 7/16”
12”12” 15”
14
Attach the doors to the frame while putting weight on the frame to keep the bed open. We recommend to have someone else sit on the frame during this step.
* The bed will not stay open on its own without the weight of a mattress.
V
W
V
W x 20
x 26
11.2
For this step x 2
12
x 20
x 28
INSTALLING THE STOPPER
Install the permanent stopper on the inside top of the cabinet while putting weight on the frame to keep the bed open. it must be placed where it will allow for the door to close flush to the front of the cabinet.
Stopper
15
INSTALLING THE MATTRESS SUPPORTS
Insert the mattress supports into the designated holes on the bed frame.
H
13
H x 2
INSTALLING THE REMAINING SLATS
14
P
O
x4
x4
x2
P
QO
OQ
Insert P and Q into their designated holes along the frame. Insert all of the remaining slats.
16
.
.
The wall bed is assembled and shown in lowered position.
Pivot the leg towards the inside of the unit. Make sure that the leg is fully retracted.
Pull up gently to close. The leg serves as a mattress retaining system. The pistons insure that the door closes properly and remains closed.
OPERATING ALL I-SEMBLE WALL BEDS WITH NON-LOCKING PISTONS**
Double
Queen
39” x 75’’
54” x 75’’
60” x 80‘’
454 kg (1000 lbs)
136 kg (300 lbs)
154 kg (340 lbs)
181 kg (400 lbs)
Bed Size Mattress Size *Mattress not includedLoad Rating
Dynamic Static
Twin
* The bed will not stay open on its own without the weight of a mattress.
Thickness
10”
RCKLR100HKD-V1
** I-SEMBLE model may vary.