4
Picture Window Double-Hung Window Joined Combinations: 4 Measure from side jamb to side jamb at bottom, middle, and top of window. Record smallest width on worksheet. Side Jamb Side Jamb Measure from wood side jamb to wood side jamb. Lower sash not shown for clarity. Tape Measure 3-1/4" Exterior Before Measuring: 4 4 4 If any rotten wood on the frame of the original window cannot be repaired or replaced, opening will not be suitable for insert window replacement. Existing opening must be plumb, level and square. If not, adjustments must be made to window size when ordering. Make sure a 3-1/4" wide pocket exists or can be created for insert window. Record measurements on “Measurement Worksheet”. Describe window locations clearly and record measurements to nearest 1/8" when recording measurements. Measure each window even if they appear the same size. Woodwright ® and tilt-wash insert windows can only be joined in 1-way combinations as shown below. Vertical Joining Horizontal Joining 1 0005441 BD Revised 01/21/11 Exterior Measure from wood side jamb to wood side jamb. Side Jamb Side Jamb Tape Measure 1 Interior Measuring Information: 4 4 4 for 400 Series Woodwright ® and Tilt-Wash Double-Hung & Picture Insert Windows For questions call 1-888-888-7020 Monday - Friday, 7 a.m. to 7 p.m. and Saturday, 8 a.m. to 4 p.m. central time. For more information and/or guides visit andersenwindows.com. Measurement Guide Thank you for choosing Andersen. Read▶this▶measurement▶guide▶from▶beginning▶to▶end▶before▶beginning.▶Read▶all▶warnings▶and▶cautions▶during▶unit▶installation.▶▶ Read▶and▶follow▶product▶installation▶guide▶for▶installation▶instructions.▶▶ “Andersen” and all other marks where denoted are trademarks of Andersen Corporation. ©2006-2011 Andersen Corporation. All rights reserved.

Installation Guide - Windows - Measuring for Custom Sizes ...€¦ · 0º- 4º 5º- 10 º 11º- 15º Measure ... Select on worksheet: Measure angle of existing sill using Method 1

  • Upload
    others

  • View
    1

  • Download
    0

Embed Size (px)

Citation preview

Page 1: Installation Guide - Windows - Measuring for Custom Sizes ...€¦ · 0º- 4º 5º- 10 º 11º- 15º Measure ... Select on worksheet: Measure angle of existing sill using Method 1

Picture Window

Double-Hung Window

Joined Combinations:

4

Measure from side jamb to side jamb at bottom, middle, and top of window. Record smallest width on worksheet.

Side JambSide Jamb

Measure from wood side jamb to wood side jamb.

Lower sash not shown for clarity.

Tape Measure

3-1/4"

Exterior

Before Measuring:

4

4

4

If any rotten wood on the frame of the original window cannot be repaired or replaced, opening will not be suitable for insert window replacement.

Existing opening must be plumb, level and square. If not, adjustments must be made to window size when ordering.

Make sure a 3-1/4" wide pocket exists or can be created for insert window.

Record measurements on “Measurement Worksheet”.

Describe window locations clearly and record measurements to nearest 1/8" when recording measurements.

Measure each window even if they appear the same size.

Woodwright® and tilt-wash insert windows can only be joined in 1-way combinations as shown below.

Vertical Joining

Horizontal Joining

1

0005441 BD Revised 01/21/11

Exterior

Measure from wood side jamb to wood side jamb.

Side JambSide Jamb

Tape Measure

1Interior

Measuring Information:

4

4

4

for 400 Series Woodwright®and Tilt-Wash Double-Hung & Picture Insert Windows

For questions call 1-888-888-7020 Monday - Friday, 7 a.m. to 7 p.m. and Saturday, 8 a.m. to 4 p.m. central time. For more information and/or guides visit andersenwindows.com.

Measurement Guide

Thank you for choosing Andersen.

▶▶ Read▶this▶measurement▶guide▶from▶beginning▶to▶end▶before▶beginning.▶Read▶all▶warnings▶and▶cautions▶during▶unit▶installation.▶▶▶▶ Read▶and▶follow▶product▶installation▶guide▶for▶installation▶instructions.▶▶

“Andersen” and all other marks where denoted are trademarks of Andersen Corporation. ©2006-2011 Andersen Corporation. All rights reserved.

Page 2: Installation Guide - Windows - Measuring for Custom Sizes ...€¦ · 0º- 4º 5º- 10 º 11º- 15º Measure ... Select on worksheet: Measure angle of existing sill using Method 1

Based on step 4, choose sill angle on worksheet.

0º Flat

8º Moderate

5

0º- 4º

5º- 10º

11º- 15º

Measure from top of sill, just behind stool, to underside of head jamb at sides and middle. Record smallest height on worksheet.

Tape Measure

(diagonals within 1/8")

Select on worksheet:

Measure angle of existing sill using Method 1 or Method 2. Record angle rounded to the nearest degree on worksheet.

Method 1

Method 2

Rise

4"

Sill

Measure rise over 4". Find sill angle on table.

4

14º Steep

Measure from corner to corner. Square openings use standard deductions and out-of-square use non-standard deductions (determined by you) to provide clearance during installation.

For square opening:

For out-of-square opening:

3Interior

Slide thin ruler behind stool (cut paint if needed) to measure stool height (B).

Height = A + B

Measure from wood head jamb to top of stool (A).

Measure from head jamb to sill.

(diagonals not within 1/8")Width deduction

Use a sill angle finder.

Rise 1/16" 1/8" 3/16" 1/4" 3/8" 7/16" 1/2" Angle 1º 2º 3º 4º 5º 6º 7º

9/16" 5/8" 11/16" 3/4" 7/8" 15/16" 1" 1-1/16" 8º 9º 10º 11º 12º 13º 14º 15º

Stool

Sill

Sill

Stool

Head Jamb

Ruler

Tape Measure

Heightdeduction

Tape Measure

Head Jamb

Angle Finder

2Interior

Insert window location

Select on worksheet:

Insert window will be built 3/8" narrower than opening width in and 1/4" shorter than opening height in to provide installation clearance.

Size insert window to provide clearance for level and square installation.

Record desired insert unit dimensions on worksheet.

1

2

Picture Window

Double-Hung Window

Measure directly behind stool.

B

A

Interior

Exterior

Thin Ruler

Andersen Sill Angle Finder

2

Page 3: Installation Guide - Windows - Measuring for Custom Sizes ...€¦ · 0º- 4º 5º- 10 º 11º- 15º Measure ... Select on worksheet: Measure angle of existing sill using Method 1

“Andersen” and all other marks where denoted are trademarks of Andersen Corporation. ©2006-2011 Andersen Corporation. All rights reserved.

Measurement Worksheetfor Andersen® 400 Series Woodwright® and Tilt-Wash Double-Hung and Picture Insert Window

Cust

omer

NAME PHONE

ADDRESS E-MAIL

CITY/STATE/ZIP ORDER DATE

Page of

non-tempered

interiorexterior

WindowLocation

Existing Opening & window size

Color& Finish

Insect Screens

GlassOptions

Grille Style & Size

Grille Pattern

new insert windowexisting opening

with no no spacer, removable between glassspacer spacer removable interior only interior

Divided Light removable Finelight™

66

white Terratone®

sandtone forest green

Low-E4® glass Low-E4® SmartSun™glass Low-E4® Sun glass

conventional

TruScene®

Part of joined combination(sketch joined)

3/4" 7/8" 1-1/8" 2-1/4" 3/4" 1" (Woodwright® divided light only)

Window #

4

(width) (height)

1STEP

Smallest measured width (to nearest 1/8")

2STEP

Smallest measured height (to nearest 1/8")

3STEP

(width) (height)

of

0005441

Notes and sketches

(sketch grille pattern)

Insert window will be 3/8" less in width and 1/4" less in height than recorded in & .

Standard deduction Non-standard deduction

(check only one)

Record desired insert unit dimension below to the nearest 1/8":

Sill Angledouble-hung and picture only

21

(width) (height)

4STEP

0º (0º- 4º)Measured sill angle: 8º (5º- 10º) 14º (11º- 15º)

Choose sill angle:5STEP

white maple (Woodwright® only)

pine oak (Woodwright® only)

equal cottage reverse cottage

half full

Single window

▶▶ See▶back▶side▶of▶worksheet▶for▶custom▶sizing▶tables.

Terratone®

forest green

HardwareEstate™ traditional

bright brass

antique brass

polished chrome

brushed chrome

satin nickel

oil rubbed bronze

distressed nickel

distressed bronze

bright brass

antique brass

polished chrome

brushed chrome

satin nickel

oil rubbed bronze

white

stone

Classic Series™

lock & keeper

Estate™

Classic Series™

(stone color for wood interiors or white color for white interiors)

double-hung sash lift(s) (optional)

1 2

1 2finger lift (pair)

bar lift

finger lift (pair)

hand lift

sash lift

hand lift

9-lite prairie A

6-lite prairie custom nonespecified equal light

tempered

4sketchpattern

sketchpattern

white

sandtone

Quantity needed of this window type:

Window Style & Sash Ratio

picturedouble-hung transom

(typically joined to top of double-hung or picture window)

none

Woodwright®

Tilt-Wash

(Woodwright® Only)

white stone

hand lift

finger lift (pair)

Page 4: Installation Guide - Windows - Measuring for Custom Sizes ...€¦ · 0º- 4º 5º- 10 º 11º- 15º Measure ... Select on worksheet: Measure angle of existing sill using Method 1

0005441

Page of

to

78" 77 1 ⁄2" 77"

0° 8° 14°

to to

Sill Angle

45 5 ⁄8"to

to

16 1 ⁄2"45 5 ⁄8"

to16 1 ⁄2"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

Cottage Reverse Cottage

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

CUSTOM WIDTHS

78" 77 1 ⁄2" 77"

0° 8° 14°

0° 8° 14°

27 3 ⁄4" 27 1 ⁄4" 26 3 ⁄4"

to to

0° 8° 14°

12 1 ⁄2" 12" 11 1 ⁄2"

to

68" 67 1 ⁄2" 67"

0° 8° 14°

0° 8° 14°

31 3 ⁄4" 31 1 ⁄4" 30 3 ⁄4"

to to

Sill Angle Sill Angle

to

78"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

11 1 ⁄2"

Woodwright® Insert Window Size Ranges

Double-Hung - Equal Sash

Picture

Custom size windows are

available in 1 ⁄ 8" increments.

Height limits for double-hung

and picture insert windows

depend on new insert window

sill angle.

For picture and transom insert

windows, either height or

width must be 68" or less and

height plus width cannot be

less then 28".to

78" 77 1 ⁄2" 77"

0° 8° 14°

to to

Sill Angle

45 5 ⁄8"to

to

16 1 ⁄2"45 5 ⁄8"

to16 1 ⁄2"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

Cottage Reverse Cottage

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

CUSTOM WIDTHS

78" 77 1 ⁄2" 77"

0° 8° 14°

0° 8° 14°

27 3 ⁄4" 27 1 ⁄4" 26 3 ⁄4"

to to

0° 8° 14°

12 1 ⁄2" 12" 11 1 ⁄2"

to

68" 67 1 ⁄2" 67"

0° 8° 14°

0° 8° 14°

31 3 ⁄4" 31 1 ⁄4" 30 3 ⁄4"

to to

Sill Angle Sill Angle

to

78"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

11 1 ⁄2"

to

78" 77 1 ⁄2" 77"

0° 8° 14°

to to

Sill Angle

45 5 ⁄8"to

to

16 1 ⁄2"45 5 ⁄8"

to16 1 ⁄2"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

Cottage Reverse Cottage

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

CUSTOM WIDTHS

78" 77 1 ⁄2" 77"

0° 8° 14°

0° 8° 14°

27 3 ⁄4" 27 1 ⁄4" 26 3 ⁄4"

to to

0° 8° 14°

12 1 ⁄2" 12" 11 1 ⁄2"

to

68" 67 1 ⁄2" 67"

0° 8° 14°

0° 8° 14°

31 3 ⁄4" 31 1 ⁄4" 30 3 ⁄4"

to to

Sill Angle Sill Angle

to

78"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

11 1 ⁄2"

to

78" 77 1 ⁄2" 77"

0° 8° 14°

to to

Sill Angle

45 5 ⁄8"to

to

16 1 ⁄2"45 5 ⁄8"

to16 1 ⁄2"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

Cottage Reverse Cottage

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

CUSTOM WIDTHS

78" 77 1 ⁄2" 77"

0° 8° 14°

0° 8° 14°

27 3 ⁄4" 27 1 ⁄4" 26 3 ⁄4"

to to

0° 8° 14°

12 1 ⁄2" 12" 11 1 ⁄2"

to

68" 67 1 ⁄2" 67"

0° 8° 14°

0° 8° 14°

31 3 ⁄4" 31 1 ⁄4" 30 3 ⁄4"

to to

Sill Angle Sill Angle

to

78"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

11 1 ⁄2"

Double-Hung - Cottage & Reverse Cottage Sash

Transom

to

78" 77 1 ⁄2" 77"

0° 8° 14°

to to

Sill Angle

44 7⁄8"to

to

21 1 ⁄4"44 7⁄8"

to21 1 ⁄4"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

Cottage Reverse Cottage

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

CUSTOM WIDTHS

91 3 ⁄4" 91 1 ⁄8" 90 5 ⁄8"

0° 8° 14°

0° 8° 14°

36 3 ⁄8" 35 3 ⁄4" 35 3 ⁄8"

to to

0° 8° 14°

12 1 ⁄2" 12" 11 1 ⁄2"

to

77 3 ⁄4" 77 1 ⁄4" 76 3 ⁄4"

0° 8° 14°

0° 8° 14°

43 3 ⁄8" 42 3 ⁄4" 42 1 ⁄4"

to to

Sill Angle Sill Angle

to

78"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

11 1 ⁄2"

Tilt-Wash Insert Window Size Ranges

Double-Hung - Equal Sash

Picture

to

78" 77 1 ⁄2" 77"

0° 8° 14°

to to

Sill Angle

44 7⁄8"to

to

21 1 ⁄4"44 7⁄8"

to21 1 ⁄4"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

Cottage Reverse Cottage

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

CUSTOM WIDTHS

91 3 ⁄4" 91 1 ⁄8" 90 5 ⁄8"

0° 8° 14°

0° 8° 14°

36 3 ⁄8" 35 3 ⁄4" 35 3 ⁄8"

to to

0° 8° 14°

12 1 ⁄2" 12" 11 1 ⁄2"

to

77 3 ⁄4" 77 1 ⁄4" 76 3 ⁄4"

0° 8° 14°

0° 8° 14°

43 3 ⁄8" 42 3 ⁄4" 42 1 ⁄4"

to to

Sill Angle Sill Angle

to

78"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

11 1 ⁄2"

to

78" 77 1 ⁄2" 77"

0° 8° 14°

to to

Sill Angle

44 7⁄8"to

to

21 1 ⁄4"44 7⁄8"

to21 1 ⁄4"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

Cottage Reverse Cottage

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

CUSTOM WIDTHS

91 3 ⁄4" 91 1 ⁄8" 90 5 ⁄8"

0° 8° 14°

0° 8° 14°

36 3 ⁄8" 35 3 ⁄4" 35 3 ⁄8"

to to

0° 8° 14°

12 1 ⁄2" 12" 11 1 ⁄2"

to

77 3 ⁄4" 77 1 ⁄4" 76 3 ⁄4"

0° 8° 14°

0° 8° 14°

43 3 ⁄8" 42 3 ⁄4" 42 1 ⁄4"

to to

Sill Angle Sill Angle

to

78"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

11 1 ⁄2"

to

78" 77 1 ⁄2" 77"

0° 8° 14°

to to

Sill Angle

44 7⁄8"to

to

21 1 ⁄4"44 7⁄8"

to21 1 ⁄4"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

Cottage Reverse Cottage

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

CUSTOM WIDTHS

91 3 ⁄4" 91 1 ⁄8" 90 5 ⁄8"

0° 8° 14°

0° 8° 14°

36 3 ⁄8" 35 3 ⁄4" 35 3 ⁄8"

to to

0° 8° 14°

12 1 ⁄2" 12" 11 1 ⁄2"

to

77 3 ⁄4" 77 1 ⁄4" 76 3 ⁄4"

0° 8° 14°

0° 8° 14°

43 3 ⁄8" 42 3 ⁄4" 42 1 ⁄4"

to to

Sill Angle Sill Angle

to

78"

78"to

11 1 ⁄2"

CUST

OM H

EIG

HTS

CUSTOM WIDTHS

11 1 ⁄2"

Double-Hung - Cottage & Reverse Cottage Sash

Transom