Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
Sleek Modern
Installation Guide
Manufactured in Canada
urbanix installation guide
table of contents:
introduction .............................................. 3urbanix architectural panels ..................... 3temperature considerations ...................... 4code compliance ....................................... 4cutting urbanix panels .............................. 4installation tips & best practices ............... 5fasteners ..................................................... 6starter strip ............................................... 6installing horizontal panels ........................7trim application ........................................ 8eaves ........................................................ 9gables ....................................................... 9installing vertical panels ........................... 10bending panel around corners .................. 11care & maintenance .................................. 12
urbanix installation guide
introduction
urbanix architectural panels
Elevate the look of your home with our urbanix Aluminum Collection. This sleek style is perfectly suited for a
modern contemporary design. Combining high strength durability and clean lines, Urbanix will instantly transform the
exterior of any project.
Incorporate it with other materials and finishes to create contrast and add curb appeal, or use it all over for a truly
breathtaking effect.
• Stunning colours, from solid low gloss bold colours to two tone authentic wood tones.
• Contemporary look is exhibited through the unique design.
• Premium 0.027” thickness.
• Manufactured with high tensile strength aluminum.
• Will not rust or rot.
Solid Two-Tone Vented Soffit
www.kaycan.com
page 3
www.kaycan.com
installation guide
temperature considerations
code compliance
cutting urbanix panels
While the expansion and contraction coefficient of urbanix panel is extremely low you must follow installation
instructions regarding spacing against trims and by allowing the panel some room to float by not
overtightening screws or nailing too tight.
The applicable Building Code and Fire Code are determined based on the project site location as there can
be various code changes per province, city and region. urbanix cannot address all the various
codes in this guide. Project Designers, Builders, Architects and Engineers must understand the applicable code
and install exterior cladding products within the guidelines of these codes. The requirements of the
Local Building Codes must be observed as a minimum requirement of the installation of urbanix.
urbanix can also be easily and cleanly cut with a
quality non-ferrous carbide tipped saw blade.
A skill saw, mitre saw or radial arm saw can all be
used to create clean cuts of the panel and trims.
Snips can also be used to clean up cuts or to cut
lengthwise down the center of a panel.
Always wear proper protective equipment when
cutting and ensure the panel and saw are on a
level plane.
Quality non-ferrous carbide tipped saw blade
Tin snips
Utility knife
safety note:Please wear safety glasses at all times
while cutting products.
page 4
installation tips & best practices
• Although highly consistent in colour and pattern, ordering of urbanix two tone panels and trims at the same
time will ensure colour continuity throughout the project.
• urbanix is manufactured from aluminum which gives it superior strength and durability,
however, urbanix panel can be damaged due to undo care or excessive pressure when fitting or handling.
• During the manufacturing process, the ends of the panels can be slightly compressed. Either cut the tongue
of the next panel to be fitted at an angle, or place a flat screwdriver in the compressed end and twist open.
• Overtightening fastening screws or nails and not being diligent placing the screws in the center of the
screwing slots can cause the panel to deflect and possibly show “oil canning “.
• The screw/nail pattern for soffit that runs parallel with the building should be fastened at maximum 24” on center
and siding applications (vertical or horizontal ) should have a maximum spacing of 16” on center.
urbanix installation guide
www.kaycan.com
fasteners (nails/screws)
Prior to selecting your fastener for the installation of the Urbanix panel, please refer to your local building code
officials for possible requirements. If no special code requirements are needed, Kaycan recommends the following :
• Screws or Nails.
• Screwss or nails should be sufficient length to allow a minimum of ¾” penetration in to the nailing base.
• Fasteners or nails must be either aluminum or stainless steel and have a head of at least 5/16” (7.9mm)
in diameter and a shank of 1/8” (3.175mm).
page 5
starter strip
Position starter strip to correct irregular conditions found in most old homes. It must be even on all sides to ensure a
proper start, remembering that the starter strip locates the bottom edge of siding. Set chalk line on each corner, up
from the bottom approximately, the width of the starter strip. Do not snap full length of chalk line at one time.
Instead, fasten line tight, then raise the line 1/4” at the center of building, hold it in position with finger, and then snap
each side. This is done to compensate for sag in the line to ensure proper alignment of siding at all four corners.
Nail furring strips around perimeters of house, using chalk line as a guide. Line up starter strip to top of furring strip
and nail approximately every 16” or at studs. Keep starter strip about 3/4” from corner of house.
Insert edge of panel into starting strip and place evenly into place. Check alignment. Make sure that urbanix panel is
interlocked in starter strip the whole length; lightly push downward and fasten approximately every 16”.
urbanix installation guide
www.kaycan.com
Chalk Line
Panels easily slide into starter
installation of urbanix panels
page 6
horizontal panel
urbanix installation guide
Y+ 1/8”
Y
Y+ 1/8”
Y
Unified panelling (using trim)
Staggered panelling (without trim)Joints between horizontal panels shall be overlapped a minimum of 1/2 in. to a maximum 3/4”, with all joint members plumb and true.
page 7
Start at rear of house and work forward so that all joints face the rear. urbanixsiding is installed with nails driven into furring strips or wall studs spaced not more than 16 in. on center. The urbanixsiding fasteners are aluminum or stainless. Nails shall be long enough to penetrate the nailing base by at least ¾ of an inch.
The urbanixsiding and accessories shall be installed in accordance with the best practice. Nails shall be centered in the siding nail slots with a minimum 1/16 in. clearance between the back of the nail head and the face of the siding. Nails shall be driven perpendicular to the substrate.
trim application
urbanix installation guide
www.kaycan.com
Y+ 1/8”
3/4” (19mm) Tab
3/4” (19mm) Notch
3/4” (19mm) Tab 3/4” (19mm) Notch
Use on all windows and doors. Position and nail or fasten before siding is engaged. A drip cap and J trim are also used
at sides and above windows and doors when the casings protrude from the side of the house. urbanix panels are then
butted up against casing and caulked, when necessary.
Where neccessary, furr out with furring strips or suitable material to keep panel in proper alignment. Apply
J-trim. Hold urbanix panel under J-trim and position in place. Lay out width. Then measure distance from lock
of urbanix panel underneath. Mark distance on urbanix panel from butt edge. Cut out using snips and knife.
Slip horizontal cut into J-trim and lock urbanix panel in regular fashion.
page 8
Install J-channel at the tops of the sidewalls. At the gable ends, snap a level chalk line along the base of the gable
and install J-channel.
After installing flashing, trim around all windows and doors using J-channel, the following sequence is suggested:
• Cut a J-channel for the bottom of the window, as wide as the frame, and install it.
• Cut side J-channels the length of the frame plus the width of the top and bottom J-channel.
Cut and bend tabs into the bottom channel. Install the side channels.
• Cut the top J-channel the width of the frame PLUS the width of the side J-channel.
• A miter cut and tab can be provided at the bottom of the window depending on the sill’s condition.
eaves
When finishing up at eaves, apply trim. Measure distance from lock panel in lower course up to J-trim allowing
horizontal cut to be hidden in trim. Mark on urbanix panel, and cut with knife.
gables
Mark pattern for cutting urbanix panels to fit gable slop by taking two short pieces of urbanix panels, holding one
horizontally on the lock of course below and the other up the side of the gable, Scribe line from “A” to “B” and cut.
Use this pattern on all successive courses until peak is reached. Caulk along both sides of gable.
urbanix installation guide
www.kaycan.com
X + 1/4”Y+ 1/8”
Y
page 9
urbanix installation guide
www.kaycan.com
standard application
Application of vertical siding is much the same as for horizontal installation, except that the urbanix panels interlock
in a vertical position. Begin at back side of the house. Select a convenient starting point and drop plumb line from
eave to foundation to locate starting line.
Fasten J-trim to the wall. Insert the starter strip into the receiving channel of the J-trim and fasten.
Then insert the first urbanix panel.
Interlock urbanix panel by inserting end into lock of urbanix panel on wall and push evenly into place.
Pushing too tight will cause stresses in the panel. Work from left to right completely around house, nailing
urbanix panels at hem every 24”, furring out where necessary to keep urbanix panels plumb.
vertical panels
Apply J-trim around windows and doors. Cut and fit panels following procedure same as for horizontal siding,
applying trim to anchor vertical cuts. On windows in most new construction, apply only J-trim to anchor
vertical cuts, caulking above and below window.
StarterJ Trim
Starter
page 10
corner application
• Make sure posts are leveled. Use a chalk line if necessary.
• Use prefabricated corners or bend it to adapt to style required.
• Secure posts by fastening at 8” or 12” intervals.
• Allow minimum 3/8” gap at bottom if the post is to be placed over decking, concrete, roofing, etc.
• For inside corners the use of J-trim is recommended.
urbanix installation guide
www.kaycan.com
OUTSIDE CORNER
WALLPANELurbanix
page 11
While factory applied finishes for aluminum panels are so durable that they will last many years longer than ordinary paints, it
is desirable to clean them thoroughly on a routine basis, especially when the finish is not washed by rain. Cleaning will
generally restore the appearance of these buildings and render repainting unnecessary. An occasional light cleaning will also
help maintain an aesthetically pleasing appearance.
Examples of applications requiring maintenance cleaning and inspection include: roof cladding, soffits, wall cladding under
eaves, garage doors and the underside of eave gutters.
Precautions1. Proper Equipment : Do not use wire brushes, abrasive cleaning tools which will mechanically abrade the coatings surface.
2. Test : always test the cleaning agents listed below in an inconspicuous area before use on a large scale.
3. Disposal: please make sure you dispose of cleaning solutions in an environmentally manner.
Washing should be done at least every 6 months and more frequently in coastal areas where marine salt spray is prevalent and
in areas where high levels of industrial fallout occur. Mild solutions of detergents will aid in the removal of most dirt, and the
following are recommended :
1. A 5% solution in water of commonly used commercial non-industrial detergents will not have any dexterous effect on a
paint surface. These solutions should be followed by an adequate rinse of water. Use a cloth or a soft brush for application.
2. The following solution is recommended to remove mildew when necessary:
• 1/3 cup dry powdered laundry detergent (ex.: TideTM)
• 1 quart sodium hypochlorite 5% solution (ex.: Clorox TM)
• 3 quarts of water
When cleaning Urbanix panels, work from the top to the bottom. Application should be gentle to prevent shiny spots.
We do not recommend the use of scouring powders or industrial solvents, since these agents may damage the paint film.
Solvent containing cleaners are very effective and can be used without concern. The surface should always be thoroughly
rinsed with clean water after cleaning to remove traces of the detergents (for all cleaning methods).
All exposed metal areas, such as scratches , are susceptible to rust and should be spot painted with touch-up paint. Also,
accumulated debris such as metal particles, leaves, branches, trash, dirt, pollution fallout, etc.., should be removed.
This removal and the regular cleaning of surfaces by a light hosing will help prevent the settling of localized areas where
accelerated corrosion might occur. Accumulations of wind borne salty deposits in seaside locations can have a particularly
aggressive effect on metal products. These salty deposits should be frequently removed by a gentle hosing with clean water.
care & maintenance
urbanix installation guide
www.kaycan.com
Any technical information or advice in this bulletin is provided without charge as a service to the industry. The use of this information or advice may produceunexpected results, and any persons intending to make use of this information are urged to carry out tests of their own to satisfy themselves they are using
the correct materials, approach, and techniques. Correctly following the information and advice should produce a satisfactory result, but Kaycan assumes no responsibility whatsoever in relation to such information or advice. Please ensure you have the most current Installation Manual.
page 12
Sleek Modern
URBINSTEng - 18A ©2018Kaycan
Colours shown are digitally reproduced. For accuracy please refer to actual product samples.
Manufactured in Canada