Upload
lycong
View
214
Download
1
Embed Size (px)
Citation preview
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Vehicle Application Guide.....................................................................................................................................................Key2GO................................................................................................................................................................................
Installation (Wiring Diagrams & Vehicle Wiring Reference chart)Type 1 - with T-Harness THNISS3D....................................................................................................................................Type 1...................................................................................................................................................................................Type 2 - with T-Harness THNISS3D....................................................................................................................................Type 2...................................................................................................................................................................................Type 3 - with T-Harness THNISS3D....................................................................................................................................Type 3...................................................................................................................................................................................Type 4 - with T-Harness THNISS3D....................................................................................................................................Type 4...................................................................................................................................................................................Type 5 - with T-Harness THNISS3D....................................................................................................................................Type 5...................................................................................................................................................................................Type 6 - with T-Harness THNISS3D....................................................................................................................................Type 6...................................................................................................................................................................................Type 7 - with T-Harness THNISS3D....................................................................................................................................Type 7...................................................................................................................................................................................Type 8 - with T-Harness THNISS3D....................................................................................................................................Type 8...................................................................................................................................................................................Type 9 - with T-Harness THNISS3D....................................................................................................................................Type 9...................................................................................................................................................................................
Programming Module Programming...........................................................................................................................................................Module Reset & Hard Reset.................................................................................................................................................Feature & Option List............................................................................................................................................................Feature Programming...........................................................................................................................................................
LED Diagnostics & Troubleshooting.....................................................................................................................................
Limited One-Year Consumer Warranty.................................................................................................................................
Quick Reference Guide........................................................................................................................................................
0203
040508091112141517182021232426272930
32343536
37
39
40
® Infiniti & Nissan are registered trademarks and property of their respective companies.
Index
Installation Guide
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
Key2GO is required for this firmware.
Important:
This guide is compatible with the NISS4HT firmware version 2.29 and higher.
The Infiniti M35h (Smart Key) is not compatible with the THNISS3D T-Harness.
The NISS4HT firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Infiniti and Nissan vehicles.
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to the Module Programming section on pages 32-33 for more information.
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2
Firmware 4HT: NISS
© 2017 Directed. All rights reserved.
Vehicle Application GuidePage 2
The table below lists the vehicles and features which are compatible with this product. Refer to the following pages formore information on installation wiring, programming and troubleshooting for these vehicles.
When armed, the aftermarket alarm (if available) will sound if the trunk is opened using the passive entry request button near the trunk. ToOEMavoid this, open the trunk using the fob button, aftermarket transmitter or SmartStart application. Alternately, you can disarm the aftermarketOEMalarm before opening the trunk.
Vehicles
2017
2016
2015
2014
2013
2012
2011
2010
2009
PK
-Im
mobili
zer
Bypass-D
ata
No
Key
Req'd
AV
-Park
ing
Lig
hts
Contr
ol
DL-A
rmF
acto
ryS
ecurity
DL-D
isarm
Facto
ryS
ecurity
DL-D
oor
Lock
Contr
ol
DL-D
oor
Unlo
ck
DL-D
river
Priority
Unlo
ck
DL-S
lidin
gD
oor
Contr
olD
river
DL-S
lidin
gD
oor
Contr
olP
assenger
DL-T
runk
/H
atc
hR
ele
ase
FO
B-C
ontr
olof
aft
erm
ark
et
ala
rmw
ith
OE
Mre
mote
Key2G
O
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onitoring
ALL
Door
Pin
s
SS
-Entr
yM
onitoring
Hood
Pin
SS
-Entr
yM
onitoring
Tru
nk/H
atc
hP
in
ST
-Bra
ke
Sta
tus
(foot
bra
ke)
ST
-E-B
rake
Sta
tus
ST
-Ignitio
nS
tatu
s
Infiniti
M35h (Smart Key) * 1 1 • • • • • • • • D • • • • • • • •
M37 (Smart Key) 2 2 2 • • • • • • • • D • • • • • • • W
M56 (Smart Key) 2 2 2 • • • • • • • • D • • • • • • • W
Q70 (Smart Key) 1 1 1 1 • • • • • • • • D • • • • • • • •
QX56 (Smart Key) 8 8 8 • • • • • • • • D • • • • • • • W
QX80 (Smart Key) 1 1 1 1 • • • • • • • • D • • • • • • • •
Nissan 17 16 15 14 13 12 11 10 09
Armada (Smart Key) 1 • • • • • • • • D • • • • • • • •
Cube (Smart Key) 1 1 1 1 1 1 • • • • • • • • D • • • • • • • •
JUKE (Smart Key) 7 7 6 6 6 6 6 • • • • • • • • D • • • • • • • •
LEAF (Smart Key) 3 • • • • • • • • D • • • • • • • •
Quest (Smart Key) 1 1 1 1 1 1 1 • • • • • • • • • • D • • • • • • • •
Sentra (Smart Key) 9 6 6 6 6 • • • • • • • • D • • • • • • • W
Versa (Smart Key) 4 4 4 4 4 • • • • • • • • D • • • • • • • •
Versa Note (Smart Key) 5 5 5 5 • • • • • • • • D • • • • • • • •
* The Infiniti M35h (Smart Key) is not compatible with the THNISS3D T-Harness.
Legend:
D: Data-to-Data (D2D) only
•: D2D and Wire-to-Wire (W2W)
W: Wire-to-Wire
PK: Transponder & Immobilizer Override
AV: Horn & Lights Controls
DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w/ FOB Remote
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Page 3
This feature is mandatory to control the immobilizer override in this firmware.
Key2GO has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It uses an array of servers to generate a duplicate of the original key, allowing the installation of a remote starter without having to give up a key.
The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.
All Key2GO-compatible firmware are clearly indicated in the function list of each vehicle search result page and will also appear on the flash page. Any first-time user must re-register to gain access to Key2GO, and some additional information will be required to complete the registration process, such as your Directed account number and store name. Key2GO requires an XKLoader.
Refer to page 33 of this guide for instructions on how to program features using Key2GO.
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Installation Type 1 - with T-Harness (THNISS3D)Page 4
Rem
ote
Sta
rter
(+) Ignition Input
NOT USED
Diagnostic Connector OBDII (connector side view)
Brake Pedal
T-01 T-01
T-02 T-02
(+) Parking Light Output
(-) Unlock Output
(-) Lock Output
See Vehicle Wiring Reference Chart.
[2] (-) Lock, (-) Unlock wires & Parking Light
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not controlled by data.
See features 5 & 7 in Feature and Option List section.
Clock & Data Wireat NATS Connector
(behind Push-to-Start button)See Vehicle Wiring Reference
Chart for wire location.
Do not use in a standard installation. Use the toggle switch supplied with the remote starter for a working Remote Start Safety Override Switch.
Brake SwitchT-Harness
(+) 12V Input
D2Donly
1 8
169
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62(-) Driver Door Trigger: Pin 47
(+)12V: Pin 70
Junction - Black 15-pin conn.(left of steering column orbehind instrument cluster)
BCMJunction - White 15-pin conn.(left of steering column orbehind instrument cluster)
(-) PTS: Pin 4
PTS - Brown or White 8-pin conn. (at PTS switch)
14 5 6 7 8
32
(-) Ground
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
[2] These connections are only required if the feature does not operate in data.
(-) Push-To-Start Output: Green/Black
Remote Start Safety Override Switch
White/Black N.C.
(+) Ignition Status Output: Violet/Brown
(+) Ignition Status Input: Violet/Green
(-) RAP Off Output: Red/Black
XKD2D65TX
(-) Ground
RX
(+) 12V
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
T-HarnessTHNISS3D(optional)
NOT USED
B-02B-01
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
(-) Door/Trunk Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(+) Ignition Input
(+) Starter 2 Output
(-) Aux2 Left Sliding Door
(+) Parking Light Output
(-) Aux1 Right Sliding Door
(-) Trunk Output
(-) Unlock Output
(-) Lock Output
(+) 12V Input
(-) Ground
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
4: White/Violet: (-) Aux1 Input
5: Violet/Black: (-) Aux2 Input
7: Pink/White: (+) Parking Light Input
[1] (AC) Tach Input
(+) Brake Input
(-) Hood Status Input
Not required in D2D mode.
(-) E-Brake Status Input
(+) Starter Output
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Immo. Data Interrupt (vehicle side): Yellow: 8
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13(+) 12V
(-) Hood Status: Blue/Red: 12Immo. Data Output (vehicle side): Orange/Black: 11
Data: Pin 3
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
Clock: Pin 2
Immo. Clock Output: Yellow/Black: 10
(+) Ignition Status Output: Violet/Brown: 9(+) Ignition Status Input: Violet/Green: 8
(+) Brake Output: Gray: 6[1] (AC) Tach Output: Violet/White: 5
(-) Door/Trunk Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
Diagnostic connector OBDII(connector side view)
1 8
169
See Vehicle Wiring Reference Chart for wire location.
CUT
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
[2] (-) Lock, (-) Unlock wires & Parking Light
See features 5 & 7 in Feature and Option List section.
(+) Brake: Pin 2
3
1 2
4
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
BCM
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
(-) Driver Door Trigger: Pin 47
PTS - Brown or White 8-pin conn. (PTS switch)
(+)12V: Pin 70
N.A.T.S Antenna Connector(behind Push-to-Start button)
White 4-pin conn.(brake switch)
(-) PTS: Pin 4
14 5 6 7 8
32
Junction - Black 15-pin conn.
(left of steering column orbehind instrument cluster)
Junction - White 15-pin conn.(left of steering column orbehind instrument cluster)
Installation Type 1Page 5
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[2] These connections are only required if the feature does not operate in data.
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65TX
(-) Ground
RX
(+) 12V
14
12
2
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Type 1 - Vehicle Wiring Reference ChartPage 6
Function Color Pin Polarity Location Color Pins
Infiniti M35h (Smart Key) 2012-2013
Brake Violet 2 (+) Brake switch. White 4
Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Green 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Brown 4 (-) PTS switch. Brown 8
12V White 70 (+) BCM left of steering column. White 15
Drivers Door Trigger Lt. Green 47 (-) BCM left of steering column. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Parking Lights Blue 2 (+) Drivers kick. White 10 or 12
Lock Brown 15 (-) Driver power window switch. White 16
Unlock Gray 16 (-) Driver power window switch. White 16
Infiniti Q70 (Smart Key) 2010-2016
Brake Violet 2 (+) Brake switch. White 4
Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Green 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Brown 4 (-) PTS switch. Brown 8
12V White 70 (+) BCM left of steering column. White 15
Drivers Door Trigger Lt. Green 47 (-) BCM left of steering column. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Parking Lights Blue 4 or 2 (hybrid) (+) Drivers kick. White 12
Lock Red or Brown (hybrid) 15 (-) Driver power window switch. White 16
Unlock Green or Gray (hybrid) 16 (-) Driver power window switch. White 16
Infiniti QX80 (Smart Key) 2014-2016
Brake Red 2 (+) Brake switch. White 4
Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Lt. Green/Red 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Lt. Blue 4 (-) PTS switch. Brown 8
12V Yellow 70 (+) BCM left of steering column. White 15
Drivers Door Trigger Gray/Red 47 (-) BCM left of steering column. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Parking Lights [3] Blue/Orange 7 (+) Drivers kick. White 10
Lock [3] Red 15 (-) Driver power window switch. White 16
Unlock [3] White 16 (-) Driver power window switch. White 16
Nissan Armada (Smart Key) 2017
Brake Red 2 (+) Brake switch. White 4
Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Lt. Green/Red 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Lt. Blue 4 (-) PTS switch. Brown 8
12V Yellow 70 (+) BCM left of steering column. White 15
Drivers Door Trigger Gray/Red 47 (-) BCM left of steering column. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Parking Lights Blue/Orange 8 (+) Drivers kick. White 10
Lock Red 15 (-) Driver power window switch. White 16
Unlock White 16 (-) Driver power window switch. White 16
Nissan CUBE (Smart Key) 2009-2014
Brake White 2 (+) Brake switch. White 2 or 4
Clock Pink/Blue 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Lt. Green 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Blue/Orange 4 (-) PTS switch. Brown 8
12V Yellow 70 (+) BCM behind dash fuse box. White 15
Drivers Door Trigger Brown/Yellow 47 (-) BCM behind dash fuse box. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Parking Lights Brown/White 13 (+) Drivers kick. White 16
Loc White/Black 8 (-) BCM behind dash fuse box. Black 40
Unlock White/Red 7 (-) BCM behind dash fuse box. Black 40
Connector Information
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Type 1 - Vehicle Wiring Reference ChartPage 7
Function Color Pin Polarity Location Color Pins
Nissan Quest (w/o Power Sliding Door) 2011-2014
Brake Lt. Green 2 (+) Brake switch. White 4Clock Red 2 Data N.A.T.S antenna connector, behind PTS button. White 4Data White 3 Data N.A.T.S antenna connector, behind PTS button. White 4PTS Violet 4 (-) PTS switch. Brown 812V Blue 70 (+) BCM behind instrument cluster. White 15Drivers Door Trigger Green 47 (-) BCM behind instrument cluster. Black 15HS CAN High Blue 6 Data OBDII. White 16HS CAN Low Pink 14 Data OBDII. White 16Parking Lights Red/Blue 8 (+) Dash fuse box. White 10Lock Gray 12 (-) BCM behind instrument cluster. Black 40
Unlock Brown 13 (-) BCM behind instrument cluster. Black 40
Nissan Quest (w/o Power Sliding Door) 2015-2016
Brake Lt. Green 2 (+) Brake switch. White 4
Clock Gray 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Pink 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Violet 4 (-) PTS switch. Brown 8
12V Blue 70 (+) BCM behind instrument cluster. White 15
Drivers Door Trigger Green 47 (-) BCM behind instrument cluster. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Parking Lights Red/Blue 8 (+) Dash fuse box. White 10
Lock Gray 12 (-) BCM behind instrument cluster. Black 40
Unlock Brown 13 (-) BCM behind instrument cluster. Black 40
Nissan Quest (with Power Sliding Door) 2011-2014
Brake Lt. Green 2 (+) Brake switch. White 4
Clock Red 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data White 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Violet 4 (-) PTS switch. Brown 8
12V Blue 70 (+) BCM behind instrument cluster. White 15
Drivers Door Trigger Green 47 (-) BCM behind instrument cluster. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Parking Lights Red/Blue 8 (+) Dash fuse box. White 10
Lock Yellow 8 (-) BCM behind instrument cluster. White 40
Unlock White 7 (-) BCM behind instrument cluster. White 40
Nissan Quest (with Power Sliding Door) 2015-2016
Brake Lt. Green 2 (+) Brake switch. White 4
Clock Gray 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Pink 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Violet 4 (-) PTS switch. Brown 8
12V Blue 70 (+) BCM behind instrument cluster. White 15
Drivers Door Trigger Green 47 (-) BCM behind instrument cluster. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Parking Lights Red/Blue 8 (+) Dash fuse box. White 10
Lock Yellow 8 (-) BCM behind instrument cluster. White 40
Unlock White 7 (-) BCM behind instrument cluster. White 40
Wire Information Connector Information
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Installation Type 2 - with T-Harness (THNISS3D)Page 8
Rem
ote
Sta
rter
(+) Ignition Input
NOT USED
Diagnostic Connector OBDII (connector side view)
Brake Pedal
T-02 T-02
T-01 T-01
(+) Parking Light Output
(-) Unlock Output
(-) Lock Output
See Vehicle Wiring Reference Chart.
[2] (-) Lock, (-) Unlock wires & Parking Light
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not controlled by data.
See features 5 & 7 in Feature and Option List section.
Clock & Data Wireat NATS Connector
(behind Push-to-Start button)See Vehicle Wiring Reference
Chart for wire location.
Brake SwitchT-Harness
(+) 12V Input
D2Donly
1 8
169
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
Junction - Black 15-pin conn.(left of steering column)
BCM Junction - White 15-pin conn.(left of steering column)
PTS - Brown or White 8-pin conn. (at PTS switch)
14 5 6 7 8
32
(-) Ground
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
[2] These connections are only required if the feature does not operate in data.
(-) Push-To-Start Output: Green/Black
Remote Start Safety Override Switch
White/Black N.C.
(+) Ignition Status Output: Violet/Brown
(+) Ignition Status Input: Violet/Green
(-) RAP Off Output: Red/Black
XKD2D65TX
(-) Ground
RX
(+) 12V
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
T-HarnessTHNISS3D(optional)
NOT USED
B-01
Do not use in a standard installation. Use the toggle switch supplied with the remote starter for a working Remote Start Safety Override Switch.
B-02
(-) Driver Door Trigger:
Lt.Green, pin 47
(+)12V: White, pin 70
(-) PTS: Brown, pin 4
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
(-) Door/Trunk Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(+) Ignition Input
(+) Starter 2 Output
(-) Aux2 Left Sliding Door
(+) Parking Light Output
(-) Aux1 Right Sliding Door
(-) Trunk Output
(-) Unlock Output
(-) Lock Output
(+) 12V Input
(-) Ground
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
4: White/Violet: (-) Aux1 Input
5: Violet/Black: (-) Aux2 Input
7: Pink/White: (+) Parking Light Input
[1] (AC) Tach Input
(+) Brake Input
(-) Hood Status Input
Not required in D2D mode.
(-) E-Brake Status Input
(+) Starter Output
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Immo. Data Interrupt (vehicle side): Yellow: 8
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13(+) 12V
(-) Hood Status: Blue/Red: 12Immo. Data Output (vehicle side): Orange/Black: 11
Data: Green, pin 3
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
Clock: Pink, pin 2
Immo. Clock Output: Yellow/Black: 10
(+) Ignition Status Output: Violet/Brown: 9(+) Ignition Status Input: Violet/Green: 8
(+) Brake Output: Gray: 6[1] (AC) Tach Output: Violet/White: 5
(-) Door/Trunk Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
Diagnostic connector OBDII(connector side view)
1 8
169
See Vehicle Wiring Reference Chart for wire location.
CUT
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
[2] (-) Lock, (-) Unlock wires & Parking Light
See features 5 & 7 in Feature and Option List section.
(+) Brake: Violet, pin 2
3
1 2
4
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
BCM
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
(-) Driver Door Trigger:
Lt.Green, pin 47
PTS - Brown or White 8-pin conn. (PTS switch)
(+)12V: White, pin 70
N.A.T.S Antenna Connector(behind Push-to-Start button)
White 4-pin conn.(brake switch)
(-) PTS: Brown, pin 4
14 5 6 7 8
32
Junction - Black 15-pin conn.
(left of steering column)
Junction - White 15-pin conn.(left of steering column)
Installation Type 2Page 9
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[2] These connections are only required if the feature does not operate in data.
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65TX
(-) Ground
RX
(+) 12V
14
12
2
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Type 2 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Infiniti M37 (Smart Key) 2011-2013
Brake Violet 2 (+) Brake switch. White 4
Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Green 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Brown 4 (-) PTS switch. Brown 8
12V White 70 (+) BCM left of steering column. White 15
Drivers Door Trigger Lt. Green 47 (-) BCM left of steering column. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Parking Lights Blue 4 (+) Drivers kick. White 10 or 12
Lock Brown or Red 15 (-) Driver power window switch. White 16
Unlock Green or Gray 16 (-) Driver power window switch. White 16
Infiniti M56 (Smart Key) 2011-2013
Brake Violet 2 (+) Brake switch. White 4
Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Green 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Brown 4 (-) PTS switch. Brown 8
12V White 70 (+) BCM left of steering column. White 15
Drivers Door Trigger Lt. Green 47 (-) BCM left of steering column. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Parking Lights Blue 4 (+) Drivers kick. White 10 or 12
Lock Red 15 (-) Driver power window switch. White 16
Unlock Green 16 (-) Driver power window switch. White 16
Connector Information
Page 10
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Rem
ote
Sta
rter
(+) Ignition Input
(-) Push-To-Start Output: Green/Black
NOT USED
NOT USED
Diagnostic Connector OBDII (connector side view)
Brake Pedal
T-02 T-02
T-01 T-01
Remote Start Safety Override Switch
White/Black N.C.
(+) Ignition Status Output: Violet/Brown
(+) Ignition Status Input: Violet/Green
(+) Parking Light Output
(-) Unlock Output
(-) Lock Output
See Vehicle Wiring Reference Chart.
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not controlled by data.
See feature 5 & 7 in Feature and Option List section.
Clock & Data Wireat NATS Connector
(behind Push-to-Start button)See Vehicle Wiring Reference Chart
for wire location.
B-01 B-02
Brake SwitchT-Harness
(+) 12V Input
D2Donly
1 8
169
(-) RAP Off Output: Red/Black
PTS - White 8-pin conn.(at PTS switch)
(-) PTS: Lt.Blue, pin 8
Junction Black 15-pin
conn.(behind
dash fuse box)
OBDII Diagnostic 16-pin connector
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
(-) Driver Door Trigger: Lt.Blue, pin 47
(+)12V: Yellow, pin 70
BCM
Junction - White 15-pin conn.(behind dash fuse box)
[2] (-) Lock, (-) Unlock wires & Parking Light
(-) Ground
14 5 6 7 8
32
Installation Type 3 - with T-Harness (THNISS3D)Page 11
[1] Tach wire is optional connection required on some remote starters, which do not support a tach signal in D2D.
[2] These connections are only required if the feature does not operate in data.
XKD2D65
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
TX
(-) Ground
RX
(+) 12V
T-HarnessTHNISS3D(optional)
Do not use in a standard installation. Use the toggle switch supplied with the remote starter for a working Remote Start Safety Override Switch.
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
(-) Door/Trunk Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(+) Ignition Input
(+) Starter 2 Output
(-) Aux2 Left Sliding Door
(+) Parking Light Output
(-) Aux1 Right Sliding Door
(-) Trunk Output
(-) Unlock Output
(-) Lock Output
(+) 12V Input
(-) Ground
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
4: White/Violet: (-) Aux1 Input
5: Violet/Black: (-) Aux2 Input
7: Pink/White: (+) Parking Light Input
[1] (AC) Tach Input
(+) Brake Input
(-) Hood Status Input
Not required in D2D mode.
(-) E-Brake Status Input
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13(+) 12V
(-) Hood Status: Blue/Red: 12Immo. Data Output (vehicle side): Orange/Black: 11
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
Immo. Clock Output: Yellow/Black: 10
(+) Ignition Status Output: Violet/Brown: 9(+) Ignition Status Input: Violet/Green: 8
(+) Brake Output: Gray: 6[1] (AC) Tach Output: Violet/White: 5
(-) Door/Trunk Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
Diagnostic connector OBDII(connector side view)
1 8
169
CUT
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
See Vehicle Wiring Reference Chart for wire location.
See features 5 & 7 in Feature and Option List section.
PTS - White 8-pin conn.( PTS switch)
(-) PTS: Lt.Blue, pin 8
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
BCM
Data: Lt. Green, pin 3
Clock: Pink, pin 2
(-) Driver Door Trigger:
Lt.Blue, pin 47
(+)12V: Yellow, pin 70
(+) Starter Output
White 4-pin conn.(brake switch)
(+) Brake: Lt.Blue or Brown, pin 2
3
1 2
4
[2] (-) Lock, (-) Unlock wires & Parking Light
N.A.T.S Antenna Connector(behind Push-to-Start button)
Junction Black 15-pin conn.
(behind dash fuse box)Junction -
White 15-pin conn.(behind dash fuse box)
Immo. Data Interrupt (vehicle side): Yellow: 8
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
14 5 6 7 8
32
Installation Type 3 Page 12
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.[2] These connections are only required if the feature does not operate in data.
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65TX
RX
(+) 12V
14
12
2
(-) Ground
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Type 3 - Vehicle Wiring Reference ChartPage 13
Function Color Pin Polarity Location Color Pins
Nissan LEAF (Smart Key) 2014
Brake Lt. Blue or Brown 2 (+) Brake switch. White 4
Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Lt. Green 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Lt. Blue 8 (-) PTS switch. White 8
12V Yellow 70 (+) BCM behind dash fuse box. White 15
Drivers Door Trigger Lt.Blue 47 (-) BCM behind dash fuse box. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Parking Lights Blue or White 30 (+) Drivers kick. White 32
Lock Red 8 (-) BCM behind dash fuse box. Black 40
Unlock Gray 7 (-) BCM behind dash fuse box. Black 40
Wire Information Connector Information
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Rem
ote
Sta
rter
(+) Ignition Input
NOT USED
NOT USED
Diagnostic Connector OBDII (connector side view)
Brake Pedal
T-02 T-02
T-01 T-01
(+) Parking Light Output
(-) Unlock Output
(-) Lock Output
See Vehicle Wiring Reference Chart.
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not controlled by data.
See features 5 & 7 in Feature and Option List section.
Clock & Data Wireat NATS
Connector (behind Push-to-Start
button)See Vehicle Wiring Reference Chart for
wire location.
B-01 B-02
Brake SwitchT-Harness
(+) 12V Input
D2Donly
1 8
169
PTS - Brown 8-pin conn.(PTS switch)
(-) PTS: Blue, pin 8
12345 6 7 8
1
2(+)12V: Green, pin 1
Black 2-pin conn.(drivers kick)
(-) Driver Door Trigger: Lt.Blue,
pin 18
BCMBlack 24-pin conn.
(drivers kick)
[2] (-) Lock, (-) Unlock wires & Parking Light
(-) Ground
20
21
23
24
19
17
16
22
15
14
13
9
11
12
7
6
5
4
10
3
2
1
18
8
(-) Push-To-Start Output: Green/Black
(+) Ignition Status Output: Violet/Brown
(+) Ignition Status Input: Violet/Green
(-) RAP Off Output: Red/Black
Installation Type 4 - with T-Harness (THNISS3D)Page 14
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
[2] These connections are only required if the feature does not operate in data.
Remote Start Safety Override Switch
White/Black N.C.
XKD2D65
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
TX
(-) Ground
RX
(+) 12V
Do not use in a standard installation. Use the toggle switch supplied with the remote starter for a working Remote Start Safety Override Switch.
T-HarnessTHNISS3D(optional)
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
(-) Door/Trunk Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(+) Ignition Input
(+) Starter 2 Output
(-) Aux2 Left Sliding Door
(+) Parking Light Output
(-) Aux1 Right Sliding Door
(-) Trunk Output
(-) Unlock Output
(-) Lock Output
(+) 12V Input
(-) Ground
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
4: White/Violet: (-) Aux1 Input
5: Violet/Black: (-) Aux2 Input
7: Pink/White: (+) Parking Light Input
[1] (AC) Tach Input
(+) Brake Input
(-) Hood Status Input
Not required in D2D mode.
(-) E-Brake Status Input
(+) Starter Output
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Immo. Data Interrupt (veh.side): Yellow: 8
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13(+) 12V
(-) Hood Status: Blue/Red: 12Immo. Data Output (vehicle side): Orange/Black: 11
Data: Lt.Green, pin 3
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
Clock: Pink, pin 2
Immo. Clock Output: Yellow/Black: 10
(+) Ignition Status Output: Violet/Brown: 9(+) Ignition Status Input: Violet/Green: 8
(+) Brake Output: Gray: 6[1] (AC) Tach Output: Violet/White: 5
(-) Door/Trunk Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
Diagnostic connector OBDII(connector side view)
1 8
169
See Vehicle Wiring Reference Chart for wire location.
CUT
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
See features 5 & 7 in Feature and Option List section.
PTS - Brown 8-pin conn.(PTS switch)
(-) Driver Door Trigger: Lt.Blue,
Pin 18
(-) PTS: Blue, pin 8
12345 6 7 8
(+)12V: Green, pin 1
2 41 3
1
2
[2] (-) Lock, (-) Unlock wires & Parking Light
20
21
23
24
19
17
16
22
15
14
13
9
11
12
7
6
5
4
10
3
2
1
18
8
N.A.T.S Antenna Connector(behind Push-to-Start button)
BCMWhite 24-pin conn.
(drivers kick)
Black 2-pin conn.(drivers kick)
Installation Type 4Page 15
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.[2] These connections are only required if the feature does not operate in data.
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65TX
(-) Ground
RX
(+) 12V
14
12
2
(+) Brake: Lt.Green, pin 2
White 4-pin conn.(brake switch)
3
1 2
4
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Type 4 - Vehicle Wiring Reference ChartPage 16
Function Color Pin Polarity Location Color Pins
Nissan Versa (Smart Key) 2013-2016
12V Green 1 (+) Drivers kick. Black 2
Brake Lt. Green 2 (+) Brake switch. White 4
Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Lt. Green 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Blue 8 (-) PTS switch. Brown 8
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Drivers Door Trigger Lt. Blue 18 (-) Drivers kick. White 24
Parking Lights Red 4 (+) Drivers kick. Gray 16
Lock Gray 8 (-) BCM behind dash fuse box. Black 40
Unlock White 7 (-) BCM behind dash fuse box. Black 40
Wire Information Connector Information
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Rem
ote
Sta
rter
(+) Ignition Input
NOT USED
NOT USED
Diagnostic Connector OBDII (connector side view)
Brake Pedal
T-02 T-02
T-01 T-01 Remote Start Safety Override Switch
White/Black N.C.
(+) Parking Light Output
(-) Unlock Output
(-) Lock Output
See Vehicle Wiring Reference Chart.
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not controlled by data.
See features 5 & 7 in Feature and Option List section.
Clock & Data Wireat NATS Connector (behind Push-to-Start
button)See Vehicle Wiring Reference Chart for
wire location..
B-01 B-02
Brake SwitchT-Harness
(+) 12V Input
D2Donly
1 8
169
PTS - Brown 8-pin conn.(at PTS switch)
12345 6 7 8
(-) Push-to-Start: Blue or Red, pin 8
(-) Driver Door Trigger: Lt.Blue,
pin 18Junction - White 24-pin conn.(at drivers kick)
(+)12V: Green, pin 11
2
Black 2-pin conn.(at drivers kick)
OBDII Diagnostic 16-pin Connector
[2] (-) Lock, (-) Unlock wires & Parking Light
20
21
23
24
19
17
16
22
15
14
13
9
11
12
7
6
5
4
10
3
2
1
18
8
Installation Type 5 - with T-Harness (THNISS3D)Page 17
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
XKD2D65
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
TX
(-) Ground
RX
(+) 12V
[2] These connections are only required if the feature does not operate in data.
(-) Push-To-Start: Green/Black
(+) Ignition Status Output: Violet/Brown
(+) Ignition Status Input: Violet/Green
(-) RAP Off Output: Red/Black
Do not use in a standard installation. Use the toggle switch supplied with the remote starter for a working Remote Start Safety Override Switch.
T-HarnessTHNISS3D(optional)
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Not required in D2D mode.
Installation Type 5 Page 18
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.[2] These connections are only required if the feature does not operate in data.
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65TX
(-) Ground
RX
(+) 12V
14
12
2
(-) Door/Trunk Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(+) Ignition Input
(+) Starter 2 Output
(-) Aux2 Left Sliding Door
(+) Parking Light Output
(-) Aux1 Right Sliding Door
(-) Trunk Output
(-) Unlock Output
(-) Lock Output
(+) 12V Input
(-) Ground
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
4: White/Violet: (-) Aux1 Input
5: Violet/Black: (-) Aux2 Input
7: Pink/White: (+) Parking Light Input
[1] (AC) Tach Input
(+) Brake Input
(-) Hood Status Input
(-) E-Brake Status Input
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13(+) 12V
(-) Hood Status: Blue/Red: 12Immo. Data Output (vehicle side): Orange/Black: 11
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
Immo. Clock Output: Yellow/Black: 10(+) Ignition Status Output: Violet/Brown: 9
(+) Ignition Status Input: Violet/Green: 8(+) Brake Output: Gray: 6
[1] (AC) Tach Output: Violet/White: 5
(-) Door/Trunk Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
Diagnostic connector OBDII(connector side view)
1 8
169
See Vehicle Wiring Reference Chart for wire location.
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
See features 5 & 7 in Feature and Option List section.
Data: Lt.Green, pin 3
Clock: Pink, pin 2
CUT
2 41 3
PTS - Brown 8-pin conn.(at PTS switch)
(-) Driver Door Trigger: Lt.Blue,
pin 18
Junction - White 24-pin conn.
(at drivers kick)
12345 6 7 8
(+)12V: Green, pin 1
1
2
Black 2-pin conn.(at drivers kick)
(-) PTS: Blue or Red, pin 8
[2] (-) Lock, (-) Unlock wires & Parking Light
N.A.T.S Antenna Connector(behind Push-to-Start button)
Immo. Data Interrupt (veh.side): Yellow: 8
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
20
21
23
24
19
17
16
22
15
14
13
9
11
12
7
6
5
4
10
3
2
1
18
8
(+) Starter Output
P#: XKD2D65TX
(-) GroundRX
(+)12V
(+) Brake: Lt. Green or Red,pin 2
3
1 2
4
White 4-pin conn.(brake switch)
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Type 5 - Vehicle Wiring Reference ChartPage 19
Function Color Pin Polarity Location Color Pins
12V Green 1 (+) Drivers kick. Black 2
Brake Lt. Green or Red 2 (+) Brake switch. White 4
Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Lt. Green 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Blue or Red 8 (-) PTS switch. Brown 8
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Drivers Door Trigger Lt. Blue 18 (-) Drivers kick. White 24
Parking Lights Red to Blue 3 (+) Drivers kick. White 32
Lock Gray 8 (-) BCM behind dash fuse box. White 40
Unlock White or Brown 7 (-) BCM behind dash fuse box. White 40
Wire Information Connector Information
Nissan Versa Note (Smart Key) 2014-2017
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Installation Type 6 - with T-Harness (THNISS3D)Page 20
Rem
ote
Sta
rter
(+) Ignition Input
NOT USED
Diagnostic Connector OBDII (connector side view)
Brake Pedal
T-01 T-01
T-02 T-02
(+) Parking Light Output
(-) Unlock Output
(-) Lock Output
See Vehicle Wiring Reference Chart.
[2] (-) Lock, (-) Unlock wires & Parking Light
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not controlled by data.
See features 5 & 7 in Feature and Option List section.
Clock & Data Wireat NATS Connector
(behind Push-to-Start button)See Vehicle Wiring Reference
Chart for wire location.
Do not use in a standard installation. Use the toggle switch supplied with the remote starter for a working Remote Start Safety Override Switch.
Brake SwitchT-Harness
(+) 12V Input
D2Donly
1 8
169
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
(-) Driver Door Trigger:
Lt.Blue or Yellow, pin 47
(+)12V: Yellow, pin 70
BCM
PTS - Brown or White 8-pin conn. (at PTS switch)
14 5 6 7 8
32
(-) Ground
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
[2] These connections are only required if the feature does not operate in data.
(-) Push-To-Start Output: Green/Black
Remote Start Safety Override Switch
White/Black N.C.
(+) Ignition Status Output: Violet/Brown
(+) Ignition Status Input: Violet/Green
(-) RAP Off Output: Red/Black
XKD2D65TX
(-) Ground
RX
(+) 12V
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
T-HarnessTHNISS3D(optional)
NOT USED
B-02B-01
(-) PTS: Lt. Green, pin 8
Junction - Black 15-pin conn.
(behind dash fuse box)
Junction - White 15-pin conn.(behind dash fuse box)
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
(-) Door/Trunk Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(+) Ignition Input
(+) Starter 2 Output
(-) Aux2 Left Sliding Door
(+) Parking Light Output
(-) Aux1 Right Sliding Door
(-) Trunk Output
(-) Unlock Output
(-) Lock Output
(+) 12V Input
(-) Ground
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
4: White/Violet: (-) Aux1 Input
5: Violet/Black: (-) Aux2 Input
7: Pink/White: (+) Parking Light Input
[1] (AC) Tach Input
(+) Brake Input
(-) Hood Status Input
Not required in D2D mode.
(-) E-Brake Status Input
(+) Starter Output
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Immo. Data Interrupt (vehicle side): Yellow: 8
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13(+) 12V
(-) Hood Status: Blue/Red: 12Immo. Data Output (vehicle side): Orange/Black: 11
Data: Lt.Green, pin 3
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
Clock: Pink, pin 2
Immo. Clock Output: Yellow/Black: 10
(+) Ignition Status Output: Violet/Brown: 9(+) Ignition Status Input: Violet/Green: 8
(+) Brake Output: Gray: 6[1] (AC) Tach Output: Violet/White: 5
(-) Door/Trunk Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
Diagnostic connector OBDII(connector side view)
1 8
169
See Vehicle Wiring Reference Chart for wire location.
CUT
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
[2] (-) Lock, (-) Unlock wires & Parking Light
See features 5 & 7 in Feature and Option List section.
(+) Brake: Lt.Blue or Red,pin 2
3
1 2
4
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
BCM
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
PTS - Brown or White 8-pin conn. (PTS switch)
N.A.T.S Antenna Connector(behind Push-to-Start button)
White 4-pin conn.(brake switch)
14 5 6 7 8
32
(-) PTS: Lt.Green,
pin 8
Junction - Black 15-pin conn.
(behind dash fuse box)
Junction - White 15-pin conn.(behind dash fuse box)
Installation Type 6Page 21
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[2] These connections are only required if the feature does not operate in data.
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65TX
(-) Ground
RX
(+) 12V
14
12
2
(-) Driver Door Trigger:
Lt.Blue or Yellow, pin 47
(+)12V: Yellow, pin 70
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Function Color Pin Polarity Location Color Pins
Nissan JUKE (Smart Key) 2011-2015
Brake - Automatic Transmission Lt. Blue or Red 2 (+) Brake switch. White 4
Brake - Manual Transmission Red 2 (+) Brake switch. White 2
Clutch Brown 4 (+) Clutch switch. White 4
Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Lt. Green 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Lt. Green 8 (-) PTS switch. Brown 8
12V Yellow 70 (+) BCM behind dash fuse box. White 15
Drivers Door Trigger Lt. Blue 47 (-) BCM behind dash fuse box. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16Lock Red 8 (-) BCM behind dash fuse box. White 40Unlock Blue 7 (-) BCM behind dash fuse box. White 40Parking Lights Violet 70 (+) Drivers kick. White 100Nissan Sentra (Smart Key) 2013-2016
Brake Lt. Blue or Red 2 (+) Brake switch. White 4Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4Data Lt. Green 3 Data N.A.T.S antenna connector, behind PTS button. White 4PTS Lt. Green 8 (-) PTS switch. White 812V Yellow 70 (+) BCM behind dash fuse box. White 15Drivers Door Trigger Yellow 47 (-) BCM behind dash fuse box. Black 15HS CAN High Blue 6 Data OBDII. White 16HS CAN Low Pink 14 Data OBDII. White 16Lock Violet 8 (-) BCM behind dash fuse box. White 40
Unlock Blue 7 (-) BCM behind dash fuse box. White 40
Parking Lights Violet 31 (+) Drivers kick. White 100
Wire Information Connector Information
Type 6 - Vehicle Wiring Reference ChartPage 22
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Installation Type 7 - with T-Harness (THNISS3D)Page 23
Rem
ote
Sta
rter
(+) Ignition Input
NOT USED
Diagnostic Connector OBDII (connector side view)
Brake Pedal
T-01 T-01
T-02 T-02
(+) Parking Light Output
(-) Unlock Output
(-) Lock Output
See Vehicle Wiring Reference Chart.
[2] (-) Lock, (-) Unlock wires & Parking Light
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not controlled by data.
See features 5 & 7 in Feature and Option List section.
Clock & Data Wireat NATS Connector
(behind Push-to-Start button)See Vehicle Wiring Reference
Chart for wire location.
Do not use in a standard installation. Use the toggle switch supplied with the remote starter for a working Remote Start Safety Override Switch.
Brake SwitchT-Harness
(+) 12V Input
D2Donly
1 8
169
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
Junction - Black 15-pin conn.(behind dash fuse box)
Junction - White 15-pin conn.(behind dash fuse box)
(-) PTS: Lt.Green, pin 8
PTS - Brown 8-pin conn. (at PTS switch)
14 5 6 7 8
32
(-) Ground
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
[2] These connections are only required if the feature does not operate in data.
(-) Push-To-Start Output: Green/Black
Remote Start Safety Override Switch
White/Black N.C.
(+) Ignition Status Output: Violet/Brown
(+) Ignition Status Input: Violet/Green
(-) RAP Off Output: Red/Black
XKD2D65TX
(-) Ground
RX
(+) 12V
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
T-HarnessTHNISS3D(optional)
NOT USED
B-02B-01
(-) Driver Door Trigger:
Lt.Blue, pin 47
(+)12V: Yellow, pin 70
BCM
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
(-) Door/Trunk Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(+) Ignition Input
(+) Starter 2 Output
(-) Aux2 Left Sliding Door
(+) Parking Light Output
(-) Aux1 Right Sliding Door
(-) Trunk Output
(-) Unlock Output
(-) Lock Output
(+) 12V Input
(-) Ground
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
4: White/Violet: (-) Aux1 Input
5: Violet/Black: (-) Aux2 Input
7: Pink/White: (+) Parking Light Input
[1] (AC) Tach Input
(+) Brake Input
(-) Hood Status Input
Not required in D2D mode.
(-) E-Brake Status Input
(+) Starter Output
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Immo. Data Interrupt (vehicle side): Yellow: 8
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13(+) 12V
(-) Hood Status: Blue/Red: 12Immo. Data Output (vehicle side): Orange/Black: 11
Data: Lt.Green, pin 3
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
Clock: Pink, pin 2
Immo. Clock Output: Yellow/Black: 10
(+) Ignition Status Output: Violet/Brown: 9(+) Ignition Status Input: Violet/Green: 8
(+) Brake Output: Gray: 6[1] (AC) Tach Output: Violet/White: 5
(-) Door/Trunk Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
Diagnostic connector OBDII(connector side view)
1 8
169
See Vehicle Wiring Reference Chart for wire location.
CUT
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
[2] (-) Lock, (-) Unlock wires & Parking Light
See features 5 & 7 in Feature and Option List section.
3
1 2
4
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
BCM
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
PTS - Brown 8-pin conn. (PTS switch)
N.A.T.S Antenna Connector(behind Push-to-Start button)
White 4-pin conn.(brake switch)
14 5 6 7 8
32
(-) PTS: Lt.Green, pin 8
Junction - Black 15-pin conn.
(behind dash fuse box)
Junction - White 15-pin conn.(behind dash fuse box)
Installation Type 7Page 24
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[2] These connections are only required if the feature does not operate in data.
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65TX
(-) Ground
RX
(+) 12V
14
12
2
(+) Brake: Lt.Blue or Red,pin 2
(-) Driver Door Trigger:
Lt.Blue, pin 47
(+)12V: Yellow, pin 70
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Function Color Pin Polarity Location Color Pins
Nissan JUKE (Smart Key) 2016-2017
Brake - Automatic Transmission Lt. Blue or Red 2 (+) Brake switch. White 4
Brake - Manual Transmission Red 2 (+) Brake switch. White 2
Clutch Brown 4 (+) Clutch switch. White 4
Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Lt. Green 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Lt. Green 8 (-) PTS switch. Brown 8
12V Yellow 70 (+) BCM behind dash fuse box. White 15
Drivers Door Trigger Lt. Blue 47 (-) BCM behind dash fuse box. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16Lock Red 8 (-) BCM behind dash fuse box. White 40Unlock Blue 7 (-) BCM behind dash fuse box. White 40
Parking Lights Violet 70 (+) Drivers kick. White 100
Wire Information Connector Information
Type 7 - Vehicle Wiring Reference ChartPage 25
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Installation Type 8 - with T-Harness (THNISS3D)Page 26
Rem
ote
Sta
rter
(+) Ignition Input
NOT USED
Diagnostic Connector OBDII (connector side view)
Brake Pedal
T-02 T-02
T-01 T-01
(+) Parking Light Output
(-) Unlock Output
(-) Lock Output
See Vehicle Wiring Reference Chart.
[2] (-) Lock, (-) Unlock wires & Parking Light
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not controlled by data.
See features 5 & 7 in Feature and Option List section.
Clock & Data Wireat NATS Connector
(behind Push-to-Start button)See Vehicle Wiring Reference
Chart for wire location.
Brake SwitchT-Harness
(+) 12V Input
D2Donly
1 8
169
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
(+)12V: Yellow, pin 70
Junction - Black 15-pin conn.(left of steering column)
BCM Junction - White 15-pin conn.(left of steering column)
(-) PTS: Lt.Blue,pin 4
PTS - Brown 8-pin conn. (at PTS switch)
14 5 6 7 8
32
(-) Ground
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
[2] These connections are only required if the feature does not operate in data.
(-) Push-To-Start Output: Green/Black
Remote Start Safety Override Switch
White/Black N.C.
(+) Ignition Status Output: Violet/Brown
(+) Ignition Status Input: Violet/Green
(-) RAP Off Output: Red/Black
XKD2D65TX
(-) Ground
RX
(+) 12V
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
T-HarnessTHNISS3D(optional)
NOT USED
B-01
Do not use in a standard installation. Use the toggle switch supplied with the remote starter for a working Remote Start Safety Override Switch.
B-02
(-) Driver Door Trigger:
Gray/Red, pin 47
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
(-) Door/Trunk Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(+) Ignition Input
(+) Starter 2 Output
(-) Aux2 Left Sliding Door
(+) Parking Light Output
(-) Aux1 Right Sliding Door
(-) Trunk Output
(-) Unlock Output
(-) Lock Output
(+) 12V Input
(-) Ground
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
4: White/Violet: (-) Aux1 Input
5: Violet/Black: (-) Aux2 Input
7: Pink/White: (+) Parking Light Input
[1] (AC) Tach Input
(+) Brake Input
(-) Hood Status Input
Not required in D2D mode.
(-) E-Brake Status Input
(+) Starter Output
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Immo. Data Interrupt (vehicle side): Yellow: 8
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13(+) 12V
(-) Hood Status: Blue/Red: 12Immo. Data Output (vehicle side): Orange/Black: 11
Data: Lt.Green/Red, pin 3
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
Clock: Pink, pin 2
Immo. Clock Output: Yellow/Black: 10
(+) Ignition Status Output: Violet/Brown: 9(+) Ignition Status Input: Violet/Green: 8
(+) Brake Output: Gray: 6[1] (AC) Tach Output: Violet/White: 5
(-) Door/Trunk Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
Diagnostic connector OBDII(connector side view)
1 8
169
See Vehicle Wiring Reference Chart for wire location.
CUT
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
[2] (-) Lock, (-) Unlock wires & Parking Light
See features 5 & 7 in Feature and Option List section.
3
1 2
4
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
BCM
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
PTS - Brown 8-pin conn. (PTS switch)
N.A.T.S Antenna Connector(behind Push-to-Start button)
White 4-pin conn.(brake switch)
(-) PTS: Lt.Blue, pin 4
14 5 6 7 8
32
Junction - Black 15-pin conn.
(left of steering column)
Junction - White 15-pin conn.(left of steering column)
Installation Type 8Page 27
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[2] These connections are only required if the feature does not operate in data.
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65TX
(-) Ground
RX
(+) 12V
14
12
2
(+) Brake: Blue/Red or Blue,pin 2
(-) Driver Door Trigger:
Gray/Red, pin 47
(+)12V: Yellow, pin 70
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Function Color Pin Polarity Location Color Pins
Infiniti QX56 (Smart Key) 2011-2013
Brake Blue/Red or Red 4 (+) Brake switch. White 2 or 4
Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4
Data Lt.Green/Red 3 Data N.A.T.S antenna connector, behind PTS button. White 4
PTS Lt. Blue 4 (-) PTS switch. Brown 8
12V Yellow 70 (+) BCM left of steering column. White 15
Drivers Door Trigger Gray/Red 47 (-) BCM left of steering column. Black 15
HS CAN High Blue 6 Data OBDII. White 16
HS CAN Low Pink 14 Data OBDII. White 16
Parking Lights Blue/Orange 8 (+) Drivers kick. White 10
Lock Red 4 or 15 (-) Driver power window switch. White 16
Unlock White 5 or 16 (-) Driver power window switch. White 16
Connector Information
Type 8 - Vehicle Wiring Reference ChartPage 28
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Installation Type 9 - with T-Harness (THNISS3D)Page 29
Rem
ote
Sta
rter
(+) Ignition Input
NOT USED
Diagnostic Connector OBDII (connector side view)
Brake Pedal
T-01 T-01
T-02 T-02
(+) Parking Light Output
(-) Unlock Output
(-) Lock Output
See Vehicle Wiring Reference Chart.
[2] (-) Lock, (-) Unlock wires & Parking Light
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not controlled by data.
See features 5 & 7 in Feature and Option List section.
Clock & Data Wireat NATS Connector
(behind Push-to-Start button)See Vehicle Wiring Reference
Chart for wire location.
Do not use in a standard installation. Use the toggle switch supplied with the remote starter for a working Remote Start Safety Override Switch.
Brake SwitchT-Harness
(+) 12V Input
D2Donly
1 8
169
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
(-) Driver Door Trigger:
Lt.Blue or Yellow, pin 47
(+)12V: Yellow, pin 70
BCM
(-) Ground
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
[2] These connections are only required if the feature does not operate in data.
(-) Push-To-Start Output: Green/Black
Remote Start Safety Override Switch
White/Black N.C.
(+) Ignition Status Output: Violet/Brown
(+) Ignition Status Input: Violet/Green
(-) RAP Off Output: Red/Black
XKD2D65TX
(-) Ground
RX
(+) 12V
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
T-HarnessTHNISS3D(optional)
NOT USED
B-02B-01
(-) PTS: Lt. Green, pin 8
Junction - Black 15-pin conn.
(behind dash fuse box)
Junction - White 15-pin conn.(behind dash fuse box)
PTS - White 8-pin conn.(at PTS switch)
12345 6 7 8
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
(-) Door/Trunk Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(+) Ignition Input
(+) Starter 2 Output
(-) Aux2 Left Sliding Door
(+) Parking Light Output
(-) Aux1 Right Sliding Door
(-) Trunk Output
(-) Unlock Output
(-) Lock Output
(+) 12V Input
(-) Ground
8: Violet: (+) Starter Input
10: Blue/White: (-) GWR (Status) Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
4: White/Violet: (-) Aux1 Input
5: Violet/Black: (-) Aux2 Input
7: Pink/White: (+) Parking Light Input
[1] (AC) Tach Input
(+) Brake Input
(-) Hood Status Input
Not required in D2D mode.
(-) E-Brake Status Input
(+) Starter Output
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Immo. Data Interrupt (vehicle side): Yellow: 8
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13(+) 12V
(-) Hood Status: Blue/Red: 12Immo. Data Output (vehicle side): Orange/Black: 11
Data: Lt.Green, pin 3
HS CAN High: Blue, pin 6
HS CAN Low: Pink, pin 14
Clock: Pink, pin 2
Immo. Clock Output: Yellow/Black: 10
(+) Ignition Status Output: Violet/Brown: 9(+) Ignition Status Input: Violet/Green: 8
(+) Brake Output: Gray: 6[1] (AC) Tach Output: Violet/White: 5
(-) Door/Trunk Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
Diagnostic connector OBDII(connector side view)
1 8
169
See Vehicle Wiring Reference Chart for wire location.
CUT
(-) RAP Off Output: Red/Black: 4
(-) Push-To-Start Output: Green/Black: 2
[2] (-) Lock, (-) Unlock wires & Parking Light
See features 5 & 7 in Feature and Option List section.
(+) Brake: Lt.Blue or Red,pin 2
3
1 2
4
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62
BCM
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
N.A.T.S Antenna Connector(behind Push-to-Start button)
White 4-pin conn.(brake switch)
(-) PTS: Lt.Green,
pin 8
Junction - Black 15-pin conn.
(behind dash fuse box)
Junction - White 15-pin conn.(behind dash fuse box)
Installation Type 9Page 30
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[2] These connections are only required if the feature does not operate in data.
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65TX
(-) Ground
RX
(+) 12V
14
12
2
(-) Driver Door Trigger:
Lt.Blue or Yellow, pin 47
(+)12V: Yellow, pin 70
PTS - White 8-pin conn.(at PTS switch)
12345 6 7 8
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Function Color Pin Polarity Location Color Pins
Nissan Sentra (Smart Key) 2017
Brake Lt. Blue or Red 2 (+) Brake switch. White 4Clock Pink 2 Data N.A.T.S antenna connector, behind PTS button. White 4Data Lt. Green 3 Data N.A.T.S antenna connector, behind PTS button. White 4PTS Lt. Green 8 (-) PTS switch. White 812V Yellow 70 (+) BCM behind dash fuse box. White 15Drivers Door Trigger Yellow 47 (-) BCM behind dash fuse box. Black 15HS CAN High Blue 6 Data OBDII. White 16HS CAN Low Pink 14 Data OBDII. White 16Lock Violet 8 (-) BCM behind dash fuse box. White 40
Unlock Blue 7 (-) BCM behind dash fuse box. White 40
Parking Lights Violet 31 (+) Drivers kick. White 100
Wire Information Connector Information
Type 9 - Vehicle Wiring Reference ChartPage 31
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Module ProgrammingPage 32
This step is required for programming only.
Remove the backup key from the transmitter.Open the transmitter, remove the battery.
REMOVEBATTERY
CR 20323V
REMOVETHE KEY
Ensure that every keyfob except one is located a minimum of 10 feet (3 meters) away from the vehicle BEFORE proceeding with the programming sequence.
Hold the keyfob in front of PTS button for steps 4 to 6.
Place and hold the keyfob in front of PTS button. Place keyfob
in front of
PTS button
2
3
1Solid
Wait until the LED turns ON solid red.
Note: To skip the transponder programming and use convenience features only, press the programming button 5 times.
Go to the next page to complete the module programming.
ImportantMake all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
When the flashing operation is successful, you can proceed with the programming instructions below.
Refer to the LED Diagnostics section on pages 37-38 for more information and for troubleshooting purposes.
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to the module, then connect the 4-pin D2D harness.
D2D Installation
W2W Installation
If required for your installation, connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
rd3
10-pinD2D
st1
th4
12-pin14-pin
nd2
rd3
Flashing a module using your computer:
1. Connect the interface module to your computer using the XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and select the Flash Module button.
3. Follow the instructions to select your vehicle, installation type, and configure your options.
4. Once you have configured the firmware options, click on the FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or tablet.
3. Select FLASH YOUR MODULE and follow the on screen instructions.
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
6
4
7
5 Press the brake pedal until the LED starts flashing orange slowly then release the pedal.
Push the PTS button once to turn the ignition OFF.
Push the PTS button twice to turn ON ignition and wait for the key light to flash.
Press Release
Brakepedal
Brakepedal
Page 33
& &Flashesslowly
Push x2
Push x1
Disconnect the module and complete the Key2GO programming.
You have successfully completed the module programming sequence.
3
2
1
Once the configuration is completed, reconnect the module. The LED turns ON solid green for 3 seconds, then turns off.
Click on Submit Key2GO Request.
Remove the module from the vehicle and reconnect it to your computer. The web site will automatically recognize that you are moving onto the second phase of the programming sequence.
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.Version 4.5 or higher of XpressVIP must be installed on your computer to complete this programming sequence.
Web Programming (for Key2GO)
Solid x3 Secs
&Off
You can now reassemble the key fob.4
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Module ResetPage 34
2
Solid
&
Solid Flashes
&
Release
3
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Release the programming button. The LED turns ON solid red.
Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
1 OR
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
10-pinD2D
st1
th5
12-pin14-pin
nd2
rd3
th4
Hard Reset
2 & &Solid SolidRelease
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED then turns ON solid red.
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.
1 OR
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
10-pinD2D
st1
th5
12-pin14-pin
nd2
rd3
th4
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Page 35
It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page.
Feature and Option List
*Default Option
Feat. Operation Flashes / Option Description
1. No RF Output* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Trunk* Will pop the trunk if available.
2. Right Sliding Door When available, will operate the right sliding door.
3. Left Sliding Door When available, will operate the left sliding door.
1. Trunk Will pop the trunk if available.
2. Right Sliding Door* When available, will operate the right sliding door.
3. Left Sliding Door When available, will operate the left sliding door.
1. Trunk Will pop the trunk if available.
2. Right Sliding Door When available, will operate the right sliding door.
3. Left Sliding Door* When available, will operate the left sliding door.
1. Disabled The remote starter parking lights wire must be connected in the vehicle.
2. Enabled* The parking lights will be controlled by CAN wires.
1. Disabled The vehicle is not equipped with an OEM alarm.
2. Enabled*
This feature must be enabled when the vehicle is equipped with an OEM security alarm.
The alarm original to the vehicle is disarmed using the bypass and Push-to-Start (PTS)
button.
1. Disabled The remote starter door lock wires must be connected in the vehicle.
2. Enabled - Type1 (EU) Works for most European vehicles.
3. Enabled - Type2 (US)*Works for most North American vehicles. (We've noticed that some North American
vehicles need to be set to "Type 1 (EU)" to work properly.)
1 RFTD Output Type
2 Trunk
3 Aux1
6 OEM Security Disarm On Data
7 Door Lock Control On Data
4 Aux2
5 Parking Light Control On Data
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
To enter feature programming routine- Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.- The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.
Changing feature options- Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. - The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green
slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.
Exiting feature programming- No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.OR
- Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.
Feature ProgrammingProgramming
Button
Page 36
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Page 37
LED Diagnostics and Troubleshooting
LED Description Troubleshooting
Module has no power.
Make sure the D2D harness is connected or that the 12
Volt is present between the red and black wires. If the
12 Volt is present, the module may be defective.
Waiting to begin the programming sequence.Ensure the correct programming procedure is being
followed.
Initialization failed.Reset the module and complete the programming again.
If the issue persists, please contact Technical Support.
Transponder functions were skipped.
(If compatible) when RXT mode is not desired or
convenience features are needed, please reset and
reprogram the module.
All required CAN networks has been detected. Normal operation.
1 of 2 CAN networks has been detected. Normal operation
Key2GO initiated.Please follow the steps indicated in “Module
programming” to complete the Key2GO programming.
Module was successfully programmed with all functions. Normal operation
Module was successfully programmed without
transponder functions.Normal operation.
CAN2 not detected.
Check the CAN2 Orange/Green and Orange/Brown wire
connections. Wake up the data bus by turning the
ignition on and try again. If your installation does not
require this connection, skip this step by pressing the
programming button 5 times.
J1850 not detected.Check the J1850 wire connection. Wake up the data bus
by turning the ignition on and try again.
CAN1 not detected.
Check the CAN1 Tan and Tan/Black wire connections.
Wake up the data bus by turning the ignition on and try
again. If your installation does not require this
connection, skip this step by pressing the programming
button 5 times.
Bypass data not detected.
Check the bypass line connection. If more than one wire
is used, make sure they are not inverted. Ensure the
vehicle still operates correctly using the factory key.
Bypass processing error.
The bypass calculation failed. Reset the module and try
again. If the condition persists, please contact Technical
Support.
ISO 1 not detected.
The Yellow/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
ISO 2 not detected.
The Orange/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
MUX not detected.
The Violet/Green or Violet/Brown wire did not detect the
expected voltage value. Refer to "Installation (wiring
diagrams & vehicle wiring reference charts)" to check
the connections.
Module Programming
Module Programming - Error Codes
Solid red
Flashes redx 1
Flashes redx 1
Flashes redx 2
Flashes redx 3
Flashes redx 4
Flashes redx 5
Flashes redx 6
Flashes redx 7
Solid greenx 3 secs
Flashesgreen
Solid orange
Flashes red& green
Off
Flashesorange
Flashesorangeslowly
Solid orangex 3 secs
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
LED Diagnostics & TroubleshootingPage 38
LED Description Troubleshooting
OBDII feature is not supported.The diagnostic data bus was not detected, therefore the
SmartStart features will be limited.
Ground When Running (Status) command received. The module has initialized the remote start sequence.
Ignition ON command received.The module has received the Ignition ON command and
is processing the remote start sequence.
Start ON command received.The module has received the Start ON command and is
processing the remote start sequence.
PTS shutdown error.The PTS output from the module was not activated due
to safety protection.
CAN bus incorrectly detected.
Verify the CAN1 and CAN2 connections. Refer to
“Installation (wiring diagrams & vehicle wiring reference
charts)” to check the connections.
LOCK command received.
UNLOCK command received.
TRUNK command received.
AUX1 command received.
AUX2 command received.
AUX3 command received.
Takeover successful. Normal operation.
Runsafe was not disabled.No UNLOCK command was received prior to opening the
door, or the 45 second timer expired in takeover mode.
Brake was not detected.The brakes were not detected, which prevents the
system from shutting down the vehicle.
Smart key was not detected.The smart key was not detected, which prevents the
system from shutting down the vehicle.
Speed was detected.The vehicle was detected as moving, which prevents the
system from shutting it down.
External module synchronization
Commands
Activation Ground When Running (Status)
If the bypass module fails to flash, it did not receive the
signal. Commands can come from RF or D2D.
Shutdown codes
(Flashes red,red thenorange) x 10
Flashes red& orange
Flashes redx 21
Flashes redx 2
Flashes redx 4
Flashes redx 10
Flashes redx 1
Flashes redx 3
Flashesgreen
Flashesgreenquickly
Flashesgreen x 1
Flashesorange x 1
Flashesorange x 2
Flashesorange x 3
Flashesorange x 5
Flashesorange x 4
Flashesorange x 6
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Rev.: 20170810
Platform: DBALL2Firmware: NISS4HT
© 2017 Directed. All rights reserved.
Limited One Year Consumer WarrantyPage 39
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
(+) Brake wire
Quick Reference GuideDBALL2-NISS4HT
© 2017 Directed. All rights reserved.
Pit Stop Mode
Get In and Go
Get In and Go is designed to provide users with easy takeover when entering their Push-to-Start (PTS) equipped vehicle, once it has been remote started.
Typically, users would have to remote start their vehicle, then get inside and press the vehicle start button to perform a takeover. There is therefore a physical action required to drive away. With Get In and Go technology, you simply remote start the vehicle, get in and go... Nothing to do but put the gear in drive and enjoy your vehicle.
This unique feature monitors a variety of parameters such as the key fob, vehicle speed sensor and door sensor, in order to perform takeover securily.
GG
Vehicle Takeover with Get In and Go*
4
3
1 Close the vehicle doors, hood and trunk, then press the Remote Start button on the transmitter to start the vehicle.**
2
Depress the brake pedal, put the car in gear and drive off.
Enter the vehicle by opening and closing the driverdoor, while making sure the key is inside with you.
Press the Unlock button on the factory or aftermarket remote.**
Ready to drive off
Press remote start
button**
Press Unlock button on
either remote**OR
** Your aftermarket remote may differ from the model shown in the illustrations.
Enter vehicle with key fob
GG
* Get In and Go connections required.
1
2
3
Stop the vehicle in a safe parking spot and put the gear in Park (P).
* Your aftermarket remote may differ from the model shown in the illustrations.
Stop & put vehicle in Park (P)
P&
Press remote start
button*
Exit vehicle with Smart Key
The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running.
Note: We recommend that you always lock the doors of your vehicle when leaving it unattended.
It is now safe to leave the engine running and exit the vehicle with the Smart Key in hand.
Press the button to remote start the vehicle.*
The parking lights will flash once to indicate the vehicle is now in Pit Stop Mode.
Complete the following steps within 45 secondsor the vehicle will shut down.
Quick Reference GuideDBALL2-NISS4HT
© 2017 Directed. All rights reserved.
Button(s) Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remote
start.
Press & hold for 5 seconds to activate
the trunk release (optional).
Press 1 time, then to activate the
right sliding door (optional).*
Press 2 times, then to activate
the left sliding door (optional).*
Press 3 times, then to activate
the panic mode.
Press once, then to reset the
remote starter runtime.
List of Available Commands
x3 +
x2 +
x1 +
x1 +
* This output is configurable. see your authorized installation center for more information.
Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.
Notes