Upload
vanthien
View
273
Download
6
Embed Size (px)
Citation preview
WARNING!
Hazard warning:
Incorrect installation or repair of Webasto heating systems may cause a fire or result in the emission of carbon monoxide, which can be fatal. Serious or fatal injuries can be caused as a result.
Specialist company training, technical documentation, specialised tools and equipment are required to install and repair Webasto heating and cooling systems.Only original Webasto parts must be used. For this, also see the catalog of air and water heat-er accessories from Webasto.
NEVER attempt to install or repair Webasto heating or cooling systems if you have not successfully completed the company training and thereby acquired the required tech-nical skills, or if you do not have access to the required technical documentation, tools and equipment needed to carry out correct installation and repairs.
ALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Webasto does not accept any liability for defects and damage that are attributable to installa-tion by untrained staff.
Water Heater
Installation documentation
Ident. No.: 1316544A_EN Fee Euro 10.00 © Webasto AG
Citroen C3
Diesel
from Model Year 2010
Left-hand drive vehicle
Manual transmission
Feel the drive
Thermo Top Evo Parking Heatere1
00 0258
Citroen C3
Table of Contents
Validity
Vehicle and engine types, equipment variants and national specifications not listed in this installation documentation have not been tested. However, installation according to this installation documentation may be possible.
The installation location of the digital timer should be confirmed with the end customer before installa-tion.
Manufacturer Model Type EG-BE No./ABECitroen C3 A51 e2 * 2007 / 46 * 0003 * ...
Engine type Engine model Output in kW Displacement in cm³9HP0 Diesel (HDI 90 FAP) 68 15609HP4 Diesel (HDI 90 FAP 99g) 68 1560
Validity 2Heater/Installation Kit 3Foreword 3General Instructions 3Special Tools 3Explanatory Notes on Document 4Preliminary Work 5Heater installation location 5Preparing electrical system 6Electrical system 8Fan controller for manual air conditioning 10Automatic air-conditioning fan controller 11
Digital timer 14Remote option (Telestart) 14Preparing installation location 15Preparing heater 16Installing heater 16Fuel 18Coolant circuit 22Combustion air 27Exhaust gas 28Final Work 30Template for Fuel Standpipe 31Operating Instructions for End Customer 32
1316544A_EN 2
Citroen C3
Heater/Installation Kit
Also required with automatic air-conditioning:
ForewordThis installation documentation applies to the vehicles Citroen C3 Diesel - for validity, see page 2 - from model year 2010 and later, assuming technical modifications to the vehicle do not affect installation, any liability claims excluded. Depending on the vehicle version and equipment, modifications may be necessary during installation with respect to this installation documentation.
However, the stipulations in this "installation documentation" and "operating and maintenance instruc-tions" for the Thermo Top Evo must always be observed.The corresponding rules of technology and any information from the vehicle manufacturer should be observed during the installation work.
General InstructionsInstallation should be carried out according to the general, standard rules of technology. Unless spec-ified otherwise, fasten hoses, lines and wiring harnesses to original vehicle lines and wiring harnesses using cable ties.Sharp edges must be provided with rub protection (cut-open fuel hose)!Spray unfinished body areas, e.g. drilled holes, with anti-corrosion wax (Tectyl 100K, Order No. 111329).When installing an IPCU, the corresponding settings must be checked or adjusted before the installa-tion.
Special Tools- Torque wrench for 2.0 - 10 Nm- Hose clamping pliers- Metric thread-setter kit
Quantity Description Order No.:1 Basic delivery scope Thermo Top Evo See price list1 Installation kit Citroen C3 2010 Diesel 1316207A1 Heater control See price list
Quantity Description Order No.:1 Add-on kit for automatic A/C Citroen C3 2010 1316209A
1316544A_EN 3
Citroen C3
Explanatory Notes on Document
To provide you with a quick overview of the individual working steps, you will find an identification mark on the outside top right corner of the page in question.
1316544A_EN 4
Special features are highlighted using the following symbols:
The arrow in the vehicle icon indicates the position on the vehicle and the viewing angle.
Specific risk of injury or fatal accidents.
Specific risk of damage to components.
Specific risk of fire or explosion.
Reference to general installation instructions of Webas-to components or to the manufacturer's vehicle-specific documents.
Reference to a special technical feature.
Mechanical system
Electrical system
Coolant circuit
Fuel
Exhaust gas
Combustion air
Software
All dimensions are in mm! Install fuel connections without impacts.Tightening torque of 5x13 heater bolts = 8Nm!Tightening torque of 5x15 bolt of water connection piece retaining plate = 7Nm!
Citroen C3
Preliminary Work
WARNING!
- Open the fuel tank cap and vent the fuel tank.- Close the tank cap again.- Depressurize the cooling system.- Copy the factory number from the original type label to the duplicate type label.- Remove years that do not apply from the duplicate label.- Attach the duplicate label (type label) in the appropriate place.- Disconnect and completely remove the battery with carrier.- Detach control unit and put it aside- Remove the air filter together with the intake hose- Remove air loading tube- Detach the wheel well trim on the right and left.- Remove bumper trim- Remove the left-hand headlight- Remove front underride protection- Fold rear seat bench- Open the right-hand fuel sender service lid.- Remove the fuel-tank sending unit in accordance with the manufacturer's instructions.- Remove instrument panel trim in the foot well on the driver's side- Detach central switching unit (BSI) on the driver side and lay it aside- Remove the instrument panel trim at the left (only with Telestart T100 HTM))- Remove radio / A/C control panel according to manufacturer's specifications (only with automatic
A/C)
Remove page 32 "Operating Instructions for End Customer" and add to the vehicle operating instruc-tions.
Installa-tion loca-tion
Heater installation location
1 Heater
1
1
1316544A_EN 5
Citroen C3
Preparing fuse holder of passen-ger com-partment
Preparing fuse holder of passen-ger com-partment
Preparing fuse holder of passen-ger com-partment
Preparing fuse holder of passen-ger com-partment
Preparing electrical system
Manual air conditioning
1 Fuse holder of passenger compartment2 M5x16 bolt, large diameter washer, flang-
ed nut3 Angle bracket
F4 25A and K1 relays are inserted in the fuse holder after installation. Insert red (rt) wire in the relay base K1/87a and black (sw) wire in relay base K1/30.
Automatic air-conditioning
1 Fuse holder of passenger compartment2 M5x16 bolt, large diameter washer, flang-
ed nut3 Angle bracket
F4 25A and K1 relays are inserted in the fuse holder after installation. Insert red (rt) wire in the relay base K1/87a and black (sw) wire in relay base K1/30. Cut out an end of 1700mm from insulation hose. Connect green/white (gn/ws) wire to K1/86 and pull into 1700mm insulation hose.
2
3
1
2
86
85 30
87a87
K1
gn/ws0,75²
F4
br0,5²
rt4²
rt/sw0,5²
F3
1
2sw4²
rt4²
2
3
1
3
86
85 30
87a87
K1
gn/ws0,75²
F4
br0,5²
rt4²
rt/sw0,5²
F3
1
2sw4²
rt4²
3
0,75²gn/ws
1316544A_EN 6
Citroen C3
Cutting wires to length
Preassem-bling IPCU
Preparing additional relay K2
Connect wires to IPCU base.IPCU view on contact side!The pre-programmed settings must be checked while performing function control on the vehicle and adjusted if necessary! Pull through wire section 10 in 800mm protective sleeving.
Duty cycle: 27%Frequency: 400HzVoltage: 10VFunction: Low-side
Produce connections as shown in wiring dia-gram.
100
bl0,75²
200
7
100
6br1²
250
9
250
8gn
0,75²
900
1011
86 85
E
A
15
IPCU
4
5
6
A
1586 85
E
7
sw0,75²
rt0,75²
1011
86
85 30
87a87
K2
8
9
1316544A_EN 7
Citroen C3
Wiring har-ness in-stallation diagram
Electrical system
Positive and earth connection
1 Positive wire on original vehicle positive sup-port point
2 Earth wire on original vehicle earth support point
Fuse holder of engine compartment
1 M5x16 bolt, retaining plate for fuse holder, large diameter washer, flanged nut
2 Angle bracket3 Retaining clip removed, M6x20 bolt, large di-
ameter washer, flanged nut4 F1-2 fuses mounted
Wiring harness pass-through to engine compartment
1 Protective rubber plug
Wiring harness pass through of passenger compartment
1 Protective rubber plug
4
1
2 54
1
2
3
Do not install the metering pump cable harness until later together with fuel pipe along the original vehicle fuel lines on the under-body
6
1
7
1
1316544A_EN 8
Citroen C3
Installing fuse holder of passen-ger com-partment
Connect-ing wiring harness of heater
Install angle bracket on bolt 4.
1 Fuse holder of passenger compartment2 F4 fuse inserted3 K1 relay mounted
Connect wiring harness of fuse holder of the engine compartment 1 and passenger com-partment 2 according to circuit diagram, such that the wires of the same colour are connect-ed.
8
4
1
2
3
92
1
1316544A_EN 9
Citroen C3
Wiring dia-gram
Legends
Connect-ing fan-mo-tor
Fan controller for manual air conditioning
Webasto components Vehicle components Colours and symbolsHG TT-Evo heater 8050 Fan motor rt redX1 6-pin heater connector PSF1 Engine compartment
fuse boxws white
X2 2-pin heater connector sw blackX10 4-pin connector
Heater control8025 A/C control panel br brown8046 Fan switch gn green
K1 Fan relay IC26 6-pin connector ge yellowF1 20A fuseF2 30A fuse Insulate wire end and tie
backF3 1A fuseF4 25 A fuse X Cutting pointa Output adapter Wiring colours may vary.
Connection on 6-pin connector IC26 1.Insulate red (rt) wire from K3/87a and tie back.Produce connections as shown in wiring dia-gram.
2 Red (rt) wire to connector of IC26 Pin33 Red (rt) wire of fan motor4 Output adapter5 Black (sw) wire from K1/30
Webasto
31
3015
Citroen
R7
2 2V NR
F11
PSF1
8025
6V NR
A2B3 A3B1A1 B2
B3A2 B2B1A3 A1
8046
6V NR
rt4²
rt4²
3IC26
8050M
12V NR 2
HG
X2 1 2 X152F2 F1
br0,5²
gn/ws0,75²
ge0,5²
rt/sw0,5²
rt4²
br0,5²
X10
86
85 30
87a87
K1
gn/ws0,75²
F4
br0,5²
rt4²
rt/sw0,5²
F3
sw4²
1
2
!rt6²
rt6²
rt4²
A
10
1
4
5
3
2
1316544A_EN 10
Citroen C3
Wiring dia-gram
Legends
Automatic air-conditioning fan controller
Webasto components Vehicle components Colours and symbolsHG TT-Evo heater 8050 Fan motor rt redX1 6-pin heater connector 8080 A/C control panel ws whiteX2 2-pin heater connector 8045 Fan controller sw blackX10 4-pin connector
Heater controlPSF1 Engine compartment
fuse boxbr brownbl blue
K1 Fan relay BSI1 Central switching unit gn greenK2 Additional relay ge yellowF1 20A fuseF2 30A fuseF3 1A fuseF4 25 A fusea Output adapterIPCU Pulse width modulatorIPCU adjustment values:Duty cycle: 27% Insulate wire end and tie
backFrequency: 400HzVoltage: 10V X Cutting pointFunction: Low-side Wiring colours may vary.
Webasto
31
3015
Citroen
rt
sw
bl
gn
4²
0,75²
0,75²
86 85
E
A
15
IPCU
0,75²
0,75²
R7
2 2V NR
F11
PSF1
gn/ws0,75²
3
bl0,75² 8
7
4
5
6
ws0,5²
86
85 30
87a87
K2
rt
4²rt
gn0,75²
1²br
9
8050M
12V NR 24V NR2 3 4 1
8045 M
ws0,5²
R7
6 10V NR
F14BSI1
1 6V NR
8080
7 26V JNws0,5²
ws0,5²
HG
X2 1 2 X152F2 F1
br1²
gn/ws0,75²
ge0,5²
rt/sw0,5²
rt4²
br0,5²
X10
86
85 30
87a87
K1
gn/ws0,75²
F4
br0,5²
rt4²
rt/sw0,5²
F3
sw4²
rt4²
1
2
br0,5²
br0,5²
10
11
!rt6²
rt6²
rt4²
A
1316544A_EN 11
Citroen C3
Connect-ing fan-mo-tor
Installing additional relay K2 and IPCU
Earth con-nection of additional relay K2 and IPCU
Connect-ing IPCU
Connection on 6-pin connector IC26 1.Insulate red (rt) wire from K1/87a and tie back.Produce connections as shown in wiring dia-gram.
2 Red (rt) wire to connector of IC26 Pin33 Red (rt) wire of fan motor4 Output adapter5 Black (sw) wire from K1/30
Insert green/white (gn/ws) wire in IPCU/86 base. Insert blue (bl) wire in base of K2/86 and brown (br) wire in base of K2/85.Produce connections as shown in wiring dia-gram.
1 K2 relay2 Original vehicle bolt3 Angle bracket4 M5x16 bolt, large diameter washer, flang-
ed nut5 IPCU mounted6 IPCU base
Produce connections as shown in wiring dia-gram.
1 Original vehicle bolt2 Brown (br) wire of IPCU/85
Connection to 26-pin connector 4 from A/C control element.Produce connections as shown in wiring dia-gram.
1 Black (sw) wire of IPCU/A2 Red (rt) wire of IPCU/E3 White (ws) wire to 26-pin connector Pin 75 White (ws) wire of fan relay
11
1
4
5
3
2
12
2
6
1
4
5
3
11
13
1
2
14
1
4
3
2
5
1316544A_EN 12
Citroen C3
Connect-ing addi-tional relay K2
Connect-ing IPCUTerminal 15
Connection to 6-pin connector 3 from A/C control element.Produce connections as shown in wiring dia-gram.
1 Green (gn) wire of K2/872 White (ws) wire of BSI4 White (ws) wire to 6-pin connector Pin 15 Green (gn) wire of K2/30
Connection on 16-pin OBD connector 4.Produce connections as shown in wiring dia-gram.
1 Blue (bl) wire of IPCU/152 White (ws) wire of Terminal 153 White (ws) wire to 16-pin OBD connector
Pin 1
15
1
3
5
4
2
16
1
4
3
2
10
1316544A_EN 13
Citroen C3
Installing digital tim-er
Installing receiver
Installing antenna
Installing tempera-ture sensor
Digital timer
1 Digital timer
Remote option (Telestart)
Fasten receiver 1 with adhesive tape.
1 Antenna
Temperature sensor T100 HTM
Fasten temperature sensor 1 behind instru-ment panel trim at left with adhesive tape.
1 17
1 18
1
19
20
1
1316544A_EN 14
Citroen C3
Preparing installa-tion loca-tion
Installing edge pro-tection
Installing bracket loosely
Copying hole pat-tern
Preparing installation location
Pull fuel line into corrugated tube 1 and route to the engine compartment. Route wiring har-ness of heater 2 to installation location.
1 200 mm edge protection2 Bend tab
1 Original vehicle bolt2 Loosely mount bracket3 M8x20 bolt, flanged nut, existing hole
After copying hole pattern at position 1, re-move bracket.
1 7 mm dia. hole2 M6x20 bolt, flanged nut, existing hole
21
1
2
22
1
2
23
2
1
3
24
1 2
1316544A_EN 15
Citroen C3
Installing coolant in-take pipe
Preassem-bling heat-er
Installing heater
Installing heater
Preparing heater
1 Coolant connection piece, sealing ring [2x each]
2 5x15 self-tapping screw, retaining plate of coolant intake pipe
1 80 mm edge protection2 5x13 self-tapping bolt [3x]
Installing heater
1 Original vehicle bolt2 M8x20 bolt, large diameter washer, flang-
ed nut, existing hole
1 M6x20 bolt, flanged nut [2x each]
1
1
2
25
26
1
2
2
2
27
1
2
28
1
1
1316544A_EN 16
Citroen C3
Mounting wiring har-ness
Installing edge pro-tection
1 Wiring harness of heater
1 90mm edge protection [2x]
291
30
1
1
1316544A_EN 17
Citroen C3
Connect-ing heater
Routing line
Installing lines
Fuel
CAUTION!Open the vehicle's fuel tank cap, ventilate the tank and then re-close the tank lock.
Catch any fuel running off with an appropriate container.
Install fuel line and metering-pump wiring harness so that they are protected against stone impact. Un-less specified otherwise, always fasten using cable ties.Mount the fuel line and wiring harness with rub protection on sharp edges.
WARNING!The fuel line and wiring harness are routed to the metering pump in as shown in the wiring harness routing diagram.
1 Fuel line2 90° moulded hose, 10 mm dia. clamp [2x]
Route fuel line and wiring harness of meter-ing pump in corrugated tube 1 to the firewall
Route fuel line and wiring harness of meter-ing pump in corrugated tube 1 on the right ve-hicle side and further to the underbody!
3112
32
1
1
33
1
1316544A_EN 18
Citroen C3
Installing lines
Installing rivet nut
Installing metering pump
Connect-ing meter-ing pump
Route fuel line and wiring harness of meter-ing pump in cable channel 2 along original ve-hicle lines to installation location of metering pump.
1 Fuel line and wiring harness of metering pump in corrugated tube
Drill 9.1mm hole at position 1 centrally be-tween the welding points
1 Rivet nut
Install support of metering pump 2 with M6x25 bolt on the rivet nut.
1 Metering pump
1 Wiring harness of metering pump, connec-tor mounted
2 Fuel line, heater, hose section, 10 mm dia. clamp [2x]
34
2
1
1
35
1
==
70
362
1
37
1
2
1316544A_EN 19
Citroen C3
Removing fuel
Installing fuel stand-pipe
Connect-ing fuel line
Routing line
Remove fuel-tank sending unit 1 in accord-ance with manufacturer's specifications.
2 Large diameter washer dia. da = 14.63 Copy hole pattern, 6 mm dia. hole
Shape fuel standpipe 1 according to tem-plate, cut to length and install.
Install fuel-tank sending unit 3 in accordance with manufacturer's specifications. Slide on corrugated tube 4 on to fuel line.
1 Fuel standpipe2 Hose section, 10 mm dia. clamp [2x]
Route fuel line of fuel tank standpipe in corru-gated tube 1 to installation location of meter-ing pump.
38
1
2
3
39
1
1
4034
1
2
41
1
1316544A_EN 20
Citroen C3
Connect-ing meter-ing pump
Check the position of the components; adjust if necessary. Check that they have free clear-ance.
1 Fuel line of fuel standpipe2 180° moulded hose, 10 mm dia. clamp [2x]
42
1
2
1316544A_EN 21
Citroen C3
Hose rout-ing dia-gram
Coolant circuit
WARNING!Any coolant running off should be collected using an appropriate container! Route coolant hoses kink-free! Unless specified otherwise, always fasten using cable ties. Position clamps so that no other hose can be damaged! When installing the hoses, the heater must be filled with coolant.The connection should be "inline" based on the following diagram:
All spring clips without a specific designation = 25 mm dia. 1 = Black (sw) rubber isolator .All connecting pipes without a specific designation and = dia. 18x18.
Ø 27
B
C
D
E
Ø 1
8x2
0
A
Ø 27
Ø 1
8x2
0
1
1316544A_EN 22
Citroen C3
Cutting hoses to length
Preparing hoses
Hole in bumper
Connect-ing heater outlet
Discard section X.Hose A = 20mm dia. 180° moulded hose
B = 850C = 160D = 250E = 870
Push braided protection hoses onto hose B, C, D und E and cut to length.Cut heat shrink plastic tubing to length.
1 50 mm long heat shrink plastic tubing [8x]
1 7 mm dia. hole2 Bumper
Route hose E to the engine compartment over the transmission.
D BX
EC
A
1 1
D 1
E
C1
1
1
11
B
43
1
1010
2
44
E
D
1316544A_EN 23
Citroen C3
Installing circulating pump and Hose B
Connect-ing heater inlet
Mounting the wiring harness of the circu-lating pump
Preparing perforated bracket
Route hose B to the engine compartment over the transmission.
1 M6x40 bolt, large diameter washer, 20mm shim, flanged nut, prepared hole
2 Bracket of circulating pump3 Circulating pump
1 Cable tie
1 Wiring harness of circulating pump
1 Perforated bracket2 Expand hole to 8 mm dia.
45
1
B
D
2
3
46
1
C
47
1
1
2
1
1316544A_EN 24
Citroen C3
Routing in engine compart-ment
Preparing perforated bracket
Installing perforated bracket
Routing in engine compart-ment
1 Spacer bracket2 Perforated bracket3 Angle bracket of exhaust silencer4 M6x20 bolt, flanged nut, ABS bracket
1 Expand hole to 8 mm dia.2 Turn perforated bracket by 15°
1 Perforated bracket2 Hose bracket3 Original vehicle bolt, bracket of coupling
line
Route hose B and E through spacer bracket 1, align hoses and shut lock. Ensure sufficient distance to neighbouring components.
48
E
4
3
1
2
B
1
2
49
2
3
1
50
B
E
1
1316544A_EN 25
Citroen C3
Cutting point
Connect-ing engine outlet
Connect-ing heat exchanger inlet
Aligning rubber iso-lator
Mount 100mm edge protection onto edge of gear at Position 3.
1 Hose section of heat exchanger inlet2 Engine-outlet hose section
1 Hose of engine outlet
Push black (sw) rubber isolator 2 onto hose E.
1 Hose on heat exchanger inlet
Align black (sw) rubber isolator 1 of battery box 2.
5112
3
52
a
B
1
53
a
2
1
B
E
54
1
2
1316544A_EN 26
Citroen C3
Cutting combus-tion air pipe to length
Installing silencer
Combustion air
Discard section X.
1 Combustion air pipea = 120
1 5x13 self-tapping bolt2 25 mm dia. spring clip3 Combustion air pipe4 51mm pipe clamp5 Silencer
a
1
X
554
2
3
5
1
1316544A_EN 27
Citroen C3
Preparing exhaust pipe
Installing silencer
Installing exhaust pipe
Installing end sec-tion
Exhaust gas
Discard section X
1 Exhaust pipea = 280
2 Exhaust end sectionb = 310
1 Pre-assembled angle bracket2 M6x16 bolt, spring lockwasher, large diam-
eter washer3 Exhaust silencer
1 Hose clamp [2x]2 Exhaust pipe
1 Align end section2 Hose clamp3 M6x20 bolt, pipe clamp, flanged nut4 Angle bracket5 M6x20 bolt, large diameter washer [2x],
flanged nut, existing hole
a b
1 2
X
56
1
2
3
57
1
21
21
3
4
5 58
4
1316544A_EN 28
Citroen C3
Cutting out wheel well trim
Aligning si-lencer
Aligning exhaust pipe
Aligning exhaust pipe
Cut out wheel well trim 1 at the markings. Dis-card section 2.
Ensure sufficient distance to perforated bracket; correct if necessary.
Ensure sufficient distance to wheel well trim; correct if necessary.
Ensure sufficient distance to wheel well trim; correct if necessary.
592
1
60
min. 20mm
61
min. 20mm
62
min. 20mm
1316544A_EN 29
Citroen C3
Cutting out underride protection
Mounting underride protection
Final Work
WARNING!Mount removed parts in reverse order.Check all hoses, clamps and all electrical connections for firm seating.Secure all loose cables using cable ties.Only use manufacturer-approved coolant.Spray heater components with anti-corrosion wax (Tectyl 100K, Order No. 111329).
- Connect the battery.- Fill and bleed the coolant circuit according to the vehicle manufacturer’s specifications.- Adjust digital timer, teach telestart- Make settings on A/C control panel according to the "Operating Instructions for End Customer".- Attach instruction label "Switch off parking heater before refueling" in the area of the filling neck- Check the proper operation of the parking heater, see the operating instructions/installation in-
structions.
Vehicles with underride protection
Cut out underride protection 1 at the mark-ings. Discard section 2
Ensure sufficient distance between exhaust section 1 and underride protection 2, correct if necessary!
6312
64
1
2
1316544A_EN Printed in Germany 03/2011 Printing: Steffen 30
Feel the driveWebasto AGPostfach 80D-82132 Stockdorf / GermanyNational Hotline: 01805 93 22 78(14 Cent aus dem deutschen Festnetz)Hotfax: 0395 5592 353Hotmail: [email protected]://www.webasto.com
Citroen C3
Template for Fuel Standpipe
1316544A_EN 31
0
100 mm
100 mm
Scale 1:1
Compare the size of the printed version with dimension lines.Permitted tolerance a maximum of 2%.
Set the printer settings to “no margin” or “minimise mar-gins” and 100% of the normal size.
Citroen C3
Manual air condition-ing
Automatic air-condi-tioning
Operating Instructions for End Customer
Please remove page and add to the vehicle operating instructions.
Note:We recommend matching the heating time to the driving time.Heating time = driving timeExample:For a driving time of approx. 20 min. (in one direction), we recommend not exceeding a switch-on time of 20 min.
In vehicles with passenger compartment monitoring this must be deactivated in addition to the vehicle settings for the heating operation .Deactivation instructions can be taken from the operating instructions of the vehicle!
Before parking the vehicle, make the following settings:
1 Air outlet to windscreen2 Set temperature to "max."3 Set fan to level "1", max. "2"
1 Set temperature to "HI“2 Air outlet on "upward"
65
3
1 2
66
1 2
1316544A_EN 32