Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2010 American Honda Motor Co., Inc. – All Rights Re
AII 43298
BACK-UP SENSORSserved. AII 43298 (1003
2011 PILOT
) 0
Issue Date
MARCH 2010
PARTS LIST
Back-up Sensor Attachment KitP/N 08V67-SZA-100A
Back-up sensor harness
Back-up sensor subharness
Control unit
Control unit bracket
14 Wire ties
Harness tape
Clip
Fuse label
Cushion tape
2 Flange nuts, 6 mm
Switch
Switch bracket
Small wire tie
Offset wire tie
1 of 168V67-SZA-1000-91
Coupler clip
Buzzer
4 Sensor clips
Buzzer bracket
Accessory User’s Information Manual
Back-up Sensor Kit2 Corner sensors
2 Center sensors (Larger)
2 of 16 AII 43298
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Small flat-tip screwdriver
Shop towel
Diagonal cutters
Ratchet
8 mm, 10 mm, and 14 mm Sockets
10 mm Combination wrench
Utility Knife
T15 Torx Wrench
Felt-tip pen
Tape
Pushpin
Drill
3 mm Drill bit
24 mm and 26 mm Hole saws T/N AKS052507
Isopropyl alcohol
Plastic Trim Tool T/N SILTRIMTL10
Eye protection
Scissors
Small rubber mallet
(1003) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
Illustration of the Back-up Sensors Installed on the Vehicle
INSTALLATION
1. Make sure you have the anti-theft code for the audio unit and the navigation system, then write down the radio presets.
2. Disconnect the negative cable from the battery.
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
792407AE
CONTROL UNIT
FUSE CASE (2 A)
BUZZER
CORNER SENSOR
CORNER SENSOR
CENTER SENSORS (LARGER)
SWITCH
BACK-UP SENSOR HARNESS
BACK-UP SENSOR SUBHARNESS
© 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 43298
3. Remove the rear cargo tray (ten clips).
4. Use a plastic trim tool to remove the cover (four retaining tabs).
5. Remove the two bolts from the rear cargo area light case.
700101BB
10 CLIPS
REAR CARGO TRAY
700102CB
REAR CARGO AREA LIGHT CASE
2 BOLTS
4 RETAINING TABS
COVER
PLASTIC TRIM TOOL
COVER
FRONT
(1003) 3 of 16
6. Release the seat belt from the rear upper trim and remove the rear upper trim (four clips and unplug the vehicle connector).
7. Remove the two seat foot covers (four retaining tabs).
8. Remove the two bolts that fasten the left third row seat to the floor. Raise the left third row seat cushion.
9. Remove the seat belt cover (two retaining clips).
700103CB
4 CLIPS
REAR UPPER TRIM
FRONTSEAT BELT
VEHICLE CONNECTOR
SEAT FOOT COVER
2 RETAINING TABS
2 BOLTS41-53 N·m(4.2-5.4 kgf·m, 30-39 lbf·ft)
LEFT THIRD ROW SEAT CUSHION
2 RETAINING CLIPS
SEAT BELT COVER
2 RETAINING TABS
4 of 16 AII 43298
10. Using a small flat-tip screwdriver, push and release the seat belt lower hook from each third row seat. Insert the seat belt lower hook to the fix hole.
11. Remove the two seat belts from the left third row seat and remove the four bolts fastening the left third row seat to the floor. Remove the left third row seat.
D2107AE
LOWER HOOK
FIX HOLE
Push. SEAT BELT
LOWER HOOK
LEFT THIRD ROW SEAT
2 SEAT BELTS
4 BOLTS41-53 N·m(30-39 lbf·ft)
(1003) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
12. Release the left rear side sill trim (four clips).
13. Open the two covers for the two tie-down hooks. Remove the two tie-down hooks from the left rear side liner (two screws).
7D1902AB
FRONT
LEFT SECOND ROW SEAT
CLIP
3 CLIPS
LEFT REAR SIDE STEP
FRONT
LEFT REAR SIDE LINER
WEATHERSTRIP
6 CLIPS
2 SCREWS
BOLT
CLIP
WASHER SCREW
2 COVERS
COVEROpen.
HOOKOpen.
7 RETAINING TABS
PLASTIC TRIM TOOL 2 TIE-DOWN
HOOKS
WEATHERSTRIP
© 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 43298
14. Remove the weatherstrip in the area shown. Remove the left rear side lining (one hook, one bolt, one washer screw, one clip, six clips, and seven retaining tabs).
15. Using a plastic trim tool, open the lid on the left C-pillar trim (two retaining tabs).
700104EB 3 CLIPS
LEFT C-PILLAR TRIM
FRONT
SEAT BELT
VEHICLE CONNECTORIf equipped.
LEFT C-PILLAR TRIM
If equipped with speaker
LID
2 RETAINING TABS
BOLT
(1003) 5 of 16
16. Using a small rubber mallet and a shop towel, gently tap the left C-pillar trim at the area marked “SIDE CURTAIN AIRBAG” to release the clip.
17. Remove the bolt from the left C-pillar trim.
18. Release the seat belt from the left C-pillar trim and remove the left C-pillar trim (three clips and unplug the vehicle connector if equipped).
19. Remove the clip from the left C-pillar trim, and install a new clip (supplied) to the left C-pillar trim.
840210BB
LEFT C-PILLAR TRIM
VEHICLE PANEL
Strike.
PIN
CLIP
LEFT C-PILLAR TRIM
FRONT
RUBBER MALLET
SHOP TOWEL
PART MARKED WITH “SIDE CURTAIN AIRBAG”
CLIP
NEW CLIP
CLIPDiscard.
LEFT C-PILLAR TRIM
6 of 16 AII 43298
20. Remove the rear bumper (two clips, two bolts, two hex bolts and twelve self-tapping screws). Have an assistant help you when removing and installing the rear bumper.
NOTE: Push down on the top of the rear bumper while pulling the bumper out.
Installing the Control Unit
21. Install the control unit bracket on the control unit.
REAR BUMPER2 HEX
BOLTS2 CLIPS
6 SELF-TAPPING SCREWS
6 SELF-TAPPING SCREWS
700202AB
CONTROL UNIT
CONTROL UNIT BRACKET
(1003) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
22. Secure the control unit bracket to the vehicle panel with the 6 mm flange nut.
Installing the Buzzer
23. Release the vehicle harness clip from the vehicle panel, and cut the clip to remove it from the vehicle harness.
700203CB
FRONT
CONTROL UNIT BRACKET
6 mm FLANGE NUT
VEHICLE PANEL
Tightening point.
CONTROL UNIT BRACKET
2 STOPS
700204AB
VEHICLE PANEL
VEHICLE HARNESS
VEHICLE HARNESS CLIP Cut off.
FRONT
VEHICLE HARNESS CLIP
© 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 43298
24. Using isopropyl alcohol on a shop towel, clean the area where the buzzer will attach. Remove the adhesive backing from the buzzer, and attach the buzzer to the buzzer bracket as shown.
25. Using one 6 mm flange nut, secure the buzzer bracket to the vehicle panel in the position where the vehicle harness clip was removed in step 23.
700205BB
BUZZER
BUZZER BRACKET
ADHESIVE BACKING
Clean with iso-propyl alcohol.
BUZZERBUZZER BRACKET
Align.
700206CB
BUZZER BRACKET
VEHICLE PANEL
6 mm FLANGE NUT
FRONT
Hold against the bracket.
(1003) 7 of 16
26. Secure the vehicle harness to the buzzer bracket with the offset wire tie as shown.
27. Route the buzzer harness along the vehicle harness, and secure it to the vehicle harness with two wire ties.
700207AB
FRONT
BUZZER BRACKET
VEHICLE HARNESS
OFFSET WIRE TIE
FRONT
VEHICLEHARNESS
BUZZER HARNESS
WIRE TIE
8 of 16 AII 43298
28. Secure the buzzer harness to the vehicle harness with three wire ties.
29. Plug the buzzer harness connector to the control unit. Bundle up the excess buzzer harness and loosely secure it to the vehicle harness with one wire tie.
700209AB
FRONTBUZZER HARNESS
VEHICLE HARNESS
3 WIRE TIES
FRONTBUZZER HARNESS
VEHICLE HARNESS
WIRE TIELoosely secure.
BUZZER CONNECTOR
CONTROL UNIT
WIRE TIELoosely secure.
BUZZER HARNESSBundle up the excess harness.
(1003) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
30. Loosely secure the buzzer harness to the vehicle harness with one wire tie.
Routing the Back-up Sensor Harness
31. Attach the 2A fuse label to the fuse case on theback-up sensor harness.
32. Plug the back-up sensor harness 12-pin connector to the control unit.
33. Route the back-up sensor harness 3-pin connector as shown and secure it to the vehicle harness with two wire ties loosely secured in step 29 and 30.
6216030B
2A FUSE LABEL
BACK-UP SENSOR HARNESS
FUSE CASE
BACK-UP SENSORHARNESS 12-PIN CONNECTOR
CONTROL UNIT
FRONT
BACK-UP SENSORHARNESS 3-PIN CONNECTOR
VEHICLE HARNESS
BACK-UP SENSORHARNESS
WIRE TIE
© 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 43298
34. Unplug the vehicle 23-pin connector, and plug the back-up sensor harness 23-pin connector to the vehicle 23-pin connector as shown.
35. Lock the 23-pin connectors as shown.
36. Route the back-up sensor harness toward the underside of the vehicle, and secure it to the vehicle harness with three wire ties.
BACK-UP SENSOR HARNESS 23-PIN CONNECTOR
VEHICLE23-PIN CONNECTOR
FRONT
23-PIN CONNECTOR
Lock.
BACK-UP SENSORHARNESS
VEHICLEHARNESS
FRONT
VEHICLEHARNESS
WIRE TIE
BACK-UP SENSORHARNESS
(1003) 9 of 16
37. Remove the vehicle ground bolt from the vehicle ground terminal. Secure the back-up sensor harness ground terminal to the vehicle ground terminal with the vehicle ground bolt you just removed.
38. Route the back-up sensor harness toward the rear of the vehicle, and secure it to the vehicle harness with three wire ties.
700214BB
FRONT
VEHICLE GROUND BOLTReuse.
VEHICLE GROUND TERMINAL
BACK-UP SENSOR HARNESS GROUND TERMINAL
VEHICLEHARNESS
WIRE TIE
BACK-UP SENSOR HARNESS
FRONT
WIRE TIE
10 of 16 AII 43298
39. Remove the vehicle grommet from the vehicle panel.
40. Route the back-up sensor harness through the vehicle grommet hole, and install the back-up sensor harness grommet into the vehicle panel.
700301BB
FRONT
VEHICLE PANEL
VEHICLE GROMMETDiscard.
REAR LIGHT
700302AB
FRONT
BACK-UP SENSOR HARNESS
BACK-UP SENSOR HARNESS GROMMET
VEHICLE PANEL
VEHICLE PANEL
Outside Cabin side
BACK-UP SENSOR HARNESS GROMMET
VEHICLE GROMMET HOLE
(1003) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
41. Slide the coupler clip onto the back-up sensor harness 6-pin connector, and secure it to the vehicle panel.
42. Secure the back-up sensor harness to the vehicle harness with one wire tie.
700303AB
FRONT
BACK-UP SENSOR HARNESS 6-PIN CONNECTOR
COUPLER CLIP
VEHICLE PANEL
BACK-UP SENSOR HARNESS
WIRE TIE
VEHICLE HARNESS
© 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 43298
Installing the Switch
43. On the back of the left rear side liner, cut the insulator to the measurement shown.
44. Using a pushpin, mark the left rear side liner in the center of the square as shown.
PUSHPIN
CENTER
RIB
LEFT REAR SIDE LINER
LEFT REAR SIDE LINER (INSIDE)
INSULATORPeel.
INSULATORCut.
LEFT REAR SIDE LINING BACKSIDE
50 mm
(1003) 11 of 16
45. While wearing eye protection, drill at the mark made in step 44 using a 26 mm hole saw. Remove any burrs.
LEFT REAR SIDE LINING
26 mm HOLE SAW
MARK
DRILL
12 of 16 AII 43298
46. Using a scissors, cut the cushion tape to the dimension shown.
47. Using isopropyl alcohol on a shop towel, clean the area where the cushion tape will attach. Attach the cushion tape you cut in step 46 to the switch bracket as shown.
48. Insert the switch into the 26 mm hole, and install the switch bracket onto the switch as shown.
49. Secure the switch bracket to the switch with one small wire tie.
SWITCH
CONNECTOR
UP
DOWN
Hole on the switch.
26 mm HOLE
LEFT REAR SIDE LINER
SWITCH
SWITCH
SWITCHBRACKET
SMALLWIRETIE
LEFT REAR SIDE LINER
SWITCHBRACKET
SIDE VIEWSWITCH
SMALLWIRE TIE
Hole in the switch.
SWITCH
10 mm
CUSHION TAPE
SWITCH BRACKET
CUSHION TAPE
(1003) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
50. Plug the back-up sensor harness 3-pin connector to the switch. Reinstall the left rear side lining and C-pillar trim.
Installing the Back-up Sensor
51. Locate the four preset marks on the inside of the bumper. Using a pushpin, pierce each of the four preset marks in two places. Make sure you pierce the right center mark in the center and the bottom.
LEFT REAR SIDE LINING
SWITCHBACK-UP SENSORHARNESS 3-PIN CONNECTOR
PUSHPIN
REAR
REARBUMPER
SCRIBEMARK
REARBUMPER
SCRIBEMARKPUSHPIN
© 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 43298
52. While wearing eye protection, drill the outer pierced marks with a 3 mm bit. Then drill the two outboard center marks using a 24 mm hole saw. Remove all burrs.
53. While wearing eye protection drill the right inner mark at the upper pierced mark with a 3 mm drill bit. On the left inner mark, drill the lower pierced mark with a 3 mm drill bit. Then drill the two center marks using a 26 mm hole saw. Remove all burrs.
24 mm HOLE SAW
3 mm DRILL BIT
REARBUMPER
BURRSRemove.
DRILL
REARBUMPER
26 mm HOLE SAW
3 mm DRILL BIT
BURRSRemove.
DRILL
26 mm HOLE SAW
3 mm DRILL BIT
BURRSRemove.
DRILL
(1003) 13 of 16
54. Install the two corner sensors in the rear bumper, using one sensor clip for each sensor.
55. Install the two center sensors in the rear bumper using one sensor clip for each sensor.
REAR BUMPER
REAR BUMPER
Outside view
Inside view
2 SENSOR CLIPS
2 HOLES 24 mm
CORNER SENSOR
CORNER SENSOR
DETENT
SENSOR CLIP
CENTER SENSOR(LARGER) SENSOR
CLIP
REARBUMPER
Outside view Inside view
Outside view
HOLE26 mm
HOLE 26 mm
REAR BUMPER
REAR BUMPER
DETENT
CENTER SENSOR(LARGER)
CENTER SENSOR(LARGER)
CENTER SENSOR (LARGER)
DETENT
Inside view
14 of 16 AII 43298
56. Plug the four back-up sensor subharness 2-pin connectors to the two corner sensors and two center sensors.
57. Attach three back-up sensor subharness clips (A) into three sensor clips.
700315AB
CORNER SENSOR
CORNER SENSOR
BACK-UP SENSOR SUBHARNESS
4 BACK-UP SENSOR SUBHARNESS 2-PIN CONNECTORS
2 CENTER SENSORS (LARGER)
700316AB
BACK-UP SENSOR SUBHARNESS
3 BACK-UP SENSOR SUBHARNESS CLIPS (A)
3 SENSOR CLIPS
(1003) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
58. Attach the four back-up sensor subharness clips (B) to the rear bumper as shown.
700317ABBACK-UP SENSOR SUBHARNESS CLIP (B)
BACK-UP SENSOR SUBHARNESS CLIP (B)
BACK-UP SENSOR SUBHARNESS
REAR BUMPER
BACK-UP SENSOR SUBHARNESS CLIP (B)
BACK-UP SENSOR SUBHARNESS CLIP (B)
Secure point.
Secure point.
Secure point.
Secure point.
© 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 43298
59. Using isopropyl alcohol on a shop towel, clean the area where the harness tape will attach. Secure the back-up sensor subharness to the rear bumper with one harness tape.
60. Secure the back-up sensor subharness to the rear bumper with one back-up sensor subharness clip (C).
61. Bring the rear bumper to the vehicle, and plug the back-up sensor subharness 6-pin connector into the back-up sensor harness 6-pin connector. Reinstall the rear bumper.
700318AB
BACK-UP SENSOR SUBHARNESS CLIP (C)
REAR BUMPER
Secure point.
BACK-UP SENSOR SUBHARNESS
HARNESS TAPE
REAR BUMPER
700319AB
BACK-UP SENSOR SUBHARNESS 6-PIN CONNECTOR
BACK-UP SENSOR HARNESS 6-PIN CONNECTOR
REAR BUMPER
(1003) 15 of 16
62. Check that all wire harnesses are routed properly and all connectors are plugged in.
63. Reinstall all removed parts.
64. Reconnect the negative cable to the battery.
65. Enter the customer’s audio system or navigation system anti-theft code.
66. Reset the clock.
67. Check the back-up sensors function as described in the Accessory User’s Information Manual.
68. Put the Accessory User’s Information Manual in the glove box.
16 of 16 AII 43298
(1003) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.