Installation 27” Built In Wall Oven

Before you beginRead these instructions carefully and completely• IMPORTANT-Save these instructions for

local inspector’s use.• IMPORTANT-Observe all governing

codes and ordinances.

27” Built In Wall OvenInstallationInstructions

JKP15, JKP18, JKP27BA, JKP27, JKP45, JKP56 JKS05,JK910AA, JK910, JK950

• Note to Installer- Be sure to leave theseinstructions with the consumer.

• OWNER- Keep these instructions for futurereference.

• NOTE- This appliance must be properlygrounded.

Parts Included

1/8” Drill Bit &Electric orHand Drill

PhillipsScrewdriver

Strain ReliefClamp

JunctionBox

Wire Nuts

36” of String

Bottom Trim4 screws (single)8 screws (double)

Tools You Will Need

Pub. No. 31-10461229C4053P429 1

“If you have questions, call 800-GE-CARES or visit our website at:www.GEAppliances.com”

Materials Needed

• Be sure your oven is installed properly bya qualified installer or service technician.

• Be sure the oven is securely installed in acabinet that is firmly attached to the housestructure. Weight on the oven door couldcause the oven to tip and result in injury.Never allow anyone to climb, sit, stand orhang on the oven door.

• Make sure the cabinets and wall cover-ings around the oven can withstand thetemperatures (up to 200°F.) generated bythe oven.

CAUTION: The electrical powerto the oven supply line must beshut off while line connectionsare being made. Failure to do so

could result in serious injury ordeath.

For Your Safety

2

Installation Instructions

This appliance must be supplied with theproper voltage and frequency, and connectedto an individual properly grounded branchcircuit, protected by a circuit breaker or fusehaving amperage as noted on rating plate.(Rating Plate is located on oven frame.)We recommend you have the electrical wiringand hookup of your oven connected by aqualified electrician. After installation, have theelectrician show you where your main ovendisconnect is located.Check with your local utilities for electricalcodes which apply in your area. Failure to wireyour oven according to governing codes couldresult in a hazardous condition. If there are nolocal codes, your range must be wired andfused to meet the requirements of the NationalElectrical Code, ANSI/NFPA No. 70-LatestEdition. You can get a copy by writing:

National Fire Protection AssociationBattery March ParkQuincy, MA 02269

Effective January 1, 1996, the NationalElectrical Code requires that new, but notexisting, construction utilize a 4 conductorconnection to an electric range. Wheninstalling an electric range in new construction,follow the instructions in the section on NEWCONSTRUCTION AND FOUR CONDUCTORBRANCH CIRCUIT CONNECTION.You must use a three-wire, single-phase A.C.208Y/120 Volt or 240/120 Volt, 60 hertzelectrical system. If you connect to aluminumwiring, properly installed connectors approvedfor use with aluminum wiring must be used.

ElectricalRequirements

IMPORTANT SAFETY INSTRUCTIONS


EASY INSTALLATION OF YOU NEW 30" WALL OVEN

Before you begin-Read these instructions completely and carefully.IMPORTANT- Save these instructions for local inspector's use.IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.Note to Installer- Be sure to leave these instructions with the consumer.OWNER- Keep these instructions for future reference.Note- This appliance must be properly grounded (if applicable).


FOR YOUR SAFETY



ELECTRICAL REQUIREMENTS




Open oven door and remove literaturepack, broiler pan and grid, and ovenracks.Remove Installation Instruction fromliterature pack and read them carefullybefore you begin.Be sure to place all literature, Use andCare, Installations, etc. in a safe placefor future reference.

Open the door to the stop position.

DO NOT LIFT THE DOOR BY THEHANDLE!

Grasp the door on both sides andlift up and off the hinges.

NOTE:The oven door is very heavy. Besure you have a firm grip before lifting theoven door off the hinges. Use cautiononce the door is removed. Do not lay thedoor on its handle. This could causedents or scratches

Remove packaging materials.Check behind hinges, and underfalse bottom. Remove labels ondoor, plastic on trims and panel,and all tape around oven.

3

ALL INSTALLATION INFORMATIONON THE FOLLOWING PAGES ARETO BE USED FOR SINGLE ANDDOUBLE OVEN INSTALLATION!

Pre- Installation Checklist

(Continued on following page)

EASY INSTALLATION OF YOUR NEW

30" WALL OVEN

Before you begin-Read these instructions completely and carefully.

IMPORTANT- Save these instructions for local inspector's use.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave these instructions with the consumer.

OWNER- Keep these instructions for future reference.

Note- This appliance must be properly grounded (if applicable).

Before you begin-Read these

instructions completely and

carefully.IMPORTANT- Save these

instructions for local inspector's use.

IMPORTANT- OBSERVE ALL

GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave

these instructions with the consumer.

OWNER- Keep these instructions

for future reference.Note- This appliance must be

properly grounded (if applicable).

FOR YOUR SAFETY
































































FOR YOUR SAFETY
































































FOR YOUR SAFETY
































































FOR YOUR SAFETY

















































FOR YOUR SAFETY




Before you begin-Read these instructions completely and carefully.IMPORTANT- Save these instructions for local inspector's use.IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.Note to Installer- Be sure to leave these instructions with the consumer.OWNER- Keep these instructions for future reference.Note- This appliance must be properly grounded (if applicable).Before you begin-Read these instructions completely and carefully.IMPORTANT- Save these instructions for local inspector's use.IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.Note to Installer- Be sure to leave these instructions with the consumer.OWNER- Keep these instructions for future reference.Note- This appliance must be properly grounded (if applicable).




FOR YOUR SAFETY








FOR YOUR SAFETY








EASY INSTALLATION OF YOUR NEW 30" WALL OVEN


FOR YOUR SAFETY





Broiler Panand Grid

Oven Racks

LiteraturePack

Pre- Installation Checklist cont.

Place the oven on a table or platformeven with the cutout opening.(Platform must support 150 lbs.single, 275 lbs. double.)

CAUTION: When the door isremoved and the hinge armsare at the stop postion, DONOT bump or try to move the

hinge arms. The hinges couldsnap back causing an injury tothe hands. Cover the hinges withtoweling or empty towel rollswhile working in the oven area.

Cover hinge with paper towel rollsor toweling.

4

Remove the bottom trim from thetop of the oven. It will be installed atthe end of installation. The trim iswrapped separately and taped to thetop of the unit.


Conduit

Bottom Trim

Side Trim

5

Cutouts for Single Built-In-OvenA1


Cabinet Width 27RecommendedCutout Locationfrom Floor 32 1/2”

Cutout Depth 23 1/2”

Cutout Width 25” Min.25 1/4” Max.

Cutout Height 27 5/8” Min.28 1/8” Max.

If the cabinets do not have a solidbottom, then two braces or runnersmust be installed to support theweight of the oven. For singleovens the runners and braces mustsupport 150 pounds.

NOTE: If the cabinet does nothave a front frame and thesides are less than 3/4” thick,shim both sides equally toestablish the cutout width.

This Oven is not approved for stackableor side by side installation

19"27"

24"

2" x 4" orEquivalentRunners

CutoutWidth

25" MIN.25 1/4" MAX.

5"

Junction BoxLocation

34"To bottom ofjunction box

10"CabinetWidth

27"

Allow a minimum of 20" for clearance to adjacent

corners, drawers, walls, etc.when door is open

Allow 7/8"for overlap of

oven over side edges of cutout

Allow 1" foroverlap of oventop and bottom

of cutout

Recommended cutout location from floor 32 1/2"

20"

2" x 4" orequivalent

runners

Alternatejunction boxlocation

CutoutHeight27 5/8" MIN.28 1/8" MAX.

CL

SUITABLE BRACINGTO SUPPORT RUNNERS

2" x 4" orEQUIVALENTRUNNERS

21 5/8"OVER CENTERLINE

OF CABINET

If the cabinet does not have a solid bottom,then two braces and runners must beinstalled to support the weight of the oven.For double ovens the runners and bracesmust support 275 pounds.

NOTE: If the cabinet does nothave a front frame and the sidesare less than 3/4” thick, shimboth sides equally to establishthe cutout width.

Cutouts for Double Built-In-OvenA2

6

Cabinet Width 27”RecommendedCutout Locationfrom Floor 13 1/4”

Cutout Depth 23 5/8” Min.

Cutout Wdth 25” Min.25 1/4” Max.

Cutout Height 49 11/16” Min.50 1/8” Max.


CutoutWidth

25" MIN.25 1/4" MAX.

5"

Junction BoxLocation

56"To bottom ofjunction box

10"CabinetWidth

27"

Allow a minimum of 20" for clearance to adjacent

corners, drawers, walls, etc.when door is open

Allow 7/8"for overlap of

oven over side edges of cutout

Allow 1" forovertlap of oventop and bottom

of cutout

Recommended cutout location from floor 13 1/4"

20"

2" x 4" orequivalent

runners

Alternatejunction

boxlocation

CutoutHeight49 11/16" MIN.50 1/8" MAX.

NOTE: This Oven is not approved to beinstalled under a Solid Disk, Induction orDowndraft Modular Cooktop.

Cutouts for Single OvenUnder Counter

A3


7

25"

Gas or electric cooktopsmay be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. Gas or electric connections

for gas cooktop must be located in an adjacent accessible location to the right

5"

240V / 208VJunction Box Location

32" TypicalCountertopHeight

24"

Allow 1"unit overlap all edges

25" MIN.25 1/4" MAX.

27 5/8" MIN.28 1/8" MAX.

3/4" SupportPlatformRequired

MUST SUPPORT 150 LBS.

22" MIN. Above

Support Platform

8

Turn off the circuit breaker or removefuses to the oven branch circuit.

With the oven in front of the cabinetopening, on a table or platform, connectthe flexible conduit to the electricaljunction box as shown below. You willneed to purchase a strain relief clampto complete the connection of theconduit to the junction box.

Electrical ConnectionsNEW CONSTRUCTION AND FOUR-CONDUCTOR BRANCH CIRCUIT

CONNECTION

• When installing in a newconstruction, or

• When installing oven in a mobilehome, or

• When local codes do not permitgrounding through neutral:

a.Cut the neutral (White) lead from the crimp.Re-strip the neutral (white) lead to exposethe proper length of conductor.

b.Attach the appliance grounding lead (greenor bare copper) in accordance with localcodes. If the residence grounding conductoris aluminum, see WARNING note.

c.Connect the oven neutral (white) lead tothe branch circuit neutral (white or gray) inaccordance with local codes, using wirenut.

d.Connect the oven red lead to the branch circuitred lead and the oven black lead to the branchcircuit black lead in accordance with localcodes, using wire nuts. If the residence red,black or white leads are aluminum conductors,see “ WARNING” note on following page.

e. Install Junction Box Cover.

JunctionBox Cover

( Continued on Next Page)

Installation InstructionsBB1

B2B3

5"JUNCTION BOXLOCATION

CONDUIT48 1/2" LONG

PLACE OVEN ON A SUPPORTTO ASSIST INCONNECTING

CONDUIT

BARE GROUND RED

BLACK

WHITE

STRAIN RELIEF CLAMP( NOT INCLUDED )

MUST BE USEDAT JUNCTION BOX

GroundWires

GroundWires

ORThree-Conductor BranchCircuit Connection

When connecting to a 3-conductor branchcircuit, if local codes permit:

WARNING: Improperconnection of aluminumhouse wiring to copper leads

can result in an electrical hazard orfire. Use only connectors designedfor joining copper to aluminum andfollow the manufacturer’srecommended procedure closely.

Do not shorten the flexible conduit.Theconduit strain Relief Clamp must besecurely attached to the junction boxand the flexible conduit must besecurely attached to the clamp. If theflexible conduit will not fit within theclamp, do not install the oven until aclamp of the proper size is obtained.

NOTE TO ELECTRICIAN: The 3 powerleads supplied with this appliance are ULrecognized for connection to larger gaugehousehold wiring. The insulation of these 3leads is rated at temperatures much higherthan the temperature rating of householdwiring. The current carrying capacity of theconductor is governed by the temperaturerating of the insulation around the wire,rather than the wire gauge alone.

JunctionBox Cover

a.Connect the bare oven ground conductorwith the crimped neutral (white) lead to thebranch circuit neutral (white or gray incolor), using wire nut.

b.Connect the oven red lead to the branchcircuit red lead, using wire nut.

c.Connect the oven black lead to the branchcircuit black lead in accordance with localcodes, using wire nut.

d.Install Junction Box Cover.

Electrial Connections cont.

9

Installation InstructionsB

B4

GroundWires

Ground andneutral wires

b. Lift oven into cabinet cutout using the ovenopening as an grip. Carefully push againstoven front frame. Do not push againstoutside edges.

c. As you slide the oven back, pull the stringso that the conduit will lie on top of the ovenin a natural loop.

d. When you are sure the conduit is out of theway, slide the oven all the way back into theopening. Remove the string.

C3

a. Drill four-1/8” pilot holes through themounting holes (top and bottom) of the sidetrim, for the four #8 screws provided. Drilleight holes for the Double Oven.

b. Secure the oven to cabinet with screwsprovided.

NOTE: Mounting screws must beused. Failure to do so could result inthe oven falling out of the cabinetcausing serious injury.

10

Note: Before drilling the pilot holesmake sure the oven is pushed as farback into the opening as it will goand centered.

Sliding the Oven Into theOpening.

C1

MOUNTING HOLE

LOCATIONS

a. Loop a 36” string around the conduit beforethe oven is slid into place. This will keep theconduit from falling behind the oven.

Placing the Oven in the OpeningC

The screws must bea minimum of 1/4”from the front of thecutout.


Installing the Bottom Trim

Side Trim

Trim ScrewLower

Trim

a. Slide the oven 3/4 way into the cabinetcutout.

b. Attach the bottomtrim to the front framewith the 3 screwsprovided.

c. Slide the oven allthe way into thecabinet cutout.

C2

CAUTION: Be sure you do not tip theoven foward during installation oryou may bend the Bottom Trim. TheBottom Trim provides an opening forcooling air to enter the cabinet. Thisopening should never be blocked.

Drilling the Pilot Holes

NOTE: If the cabinet is particle board, youmust use 4 #8 x 3/4 particle board screws.These may be purchased at any hardwarestore.

Pull out on stringloop whilepushing the oveninto the cabinet

D1Remove the toweling or paper towelholder from the hinge.

Make sure the hinge is in the doorstop position.

Grasp the door on both sides.

Hold the door over the hinges lining upthe hinges with the hinge slots on thebottom of the door.Slide the door down onto the hinges asfar as it will go.

D2

D3D4

D5Close the door.D6

The oven door is heavy. You may needhelp lifting the door high enough toslide it down onto the hinges. Do notlift the door by the handle.

11

Replacing the Oven DoorDInstallation Instructions

12


Pub. No. 31-10461229C4053P429

PRE-TEST CHECK LISTERemove all protective film if present,and any stickers.

Check to be sure that all wiring issecure and not pinched or in contactwith moving parts.

Check that the bottom trim is installedproperly (see page 7).

Check to be sure the mounting screwsare installed and flush with the sidetrim, (see page 7).

Operation Checklist

Remove all items from the insideof the oven.

Turn on the power to the oven.(Refer to your Use and CareManual.) Verify that the bake andbroil units, and all cookingfunctionsoperate properly.

Check that the circuit breaker isnot tripped or the house fuse isblown.

Check that conduit is securelyconnected to the junction box.

See Use & Care manual fortroubleshooting list.

NOTE TO ELECTRICIAN:The power leads supplied with thisappliance are UL recognized forconnections to larger gaugehousehold wiring. The insulation ofthese leads is rated at temperaturesmuch higher than the temperaturerating of household wiring. Thecurrent carrying capacity of aconductor is governed by the wiregauge and also the temperature ratingof the insulation around the wire.

NOTE: ALUMINUM WIRINGA. WARNING:

IMPROPER CONNECTION OFALUMINUM HOUSE WIRING TOTHE COPPER LEADS CANRESULT IN A SERIOUS PROBLEM.

B. Splice copper wires to aluminumwiring using special connectorsdesigned and UL approved forjoining copper to aluminum andfollow the manufacturer’srecommended connectorprocedure closely.

NOTE:Wire used, location andenclosure of splices, etc., mustconform to good wiring practice andlocal codes.

Documents

Installation 27” Built In Wall Oven