29
Inspired By Challenge Met al seat ed valves

Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

  • Upload
    others

  • View
    8

  • Download
    0

Embed Size (px)

Citation preview

Page 1: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

Inspired By Chal lenge

Met al seat ed valves

Page 2: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

2

Floating Ball Valves

Metal seated valves

Introduction

Metal seated ball valve

Habonim’s tough line of metal seated valves excels in the harshest industrial environments, where valve failures can damage plant

e�ciency, reduce pro�tability and endanger safety. Habonim’s meticulously engineered metal seated valve can withstand the

harshest applications and process conditions, including extreme high temperature, high pressure and abrasive medium. Careful

metallurgical selection of all valve parts, the development of special surface, including and hard coatings, and thorough analyses

of mechanical strength and thermal expansion ensure that the Habonim MTM line is the best choice for industry’s toughest

applications.

The lower temperature range from -60°C (-76°F) to �00°C (75�°F) undergoes Habonim’s unique surface treatment, LTPN (Low

Temperature Plasma carbo-Nitriding). LTPN is a cost e�ective hardening system for austenitic stainless steel, which provides a

minimum thickness of �0 microns and more than triple (>6�HRC) the natural hardness of the base material.

For the higher temperature range from �00°C (75�°F) and up to 5��°C (�000°F) Habonim o�ers various HVOF spray solutions

based on chromium and tungsten carbides.

For the even higher temperature range from 5��°C (�000°F) and up to 650°C (��00°F) Habonim uses ASME B�6.�� listed forged

bar material for the construction of the valve pressure-containing elements.

For the severe abrasive conditions of the pulp and paper industry, Habonim o�ers also a minimum of �.5 mm thick, hard stellite

coating. Each coating is speci�cally engineered to the customer’s application in order to provide outstanding resistance to

abrasion and corrosion for a lifetime of e�ective operation in harsh applications.

Each ball and seat sub-assembly is accurately machined, ground and then mate-lapped for a perfect match. The complete valve

assembly demonstrates high repeatability in terms of sealing (Rate B - factory tested), low torque and smooth operation at various

temperatures and pressures.

Habonim uses ASME B�6.�� listed cast material for the valve body and ends.

Standards of compliance

Factory certi�cation ISO 900�-�00� Quality management system

ANSI B�6.��, API 6D / ISO �����, ISO �7�9� Valve design

ANSI B�.�0.� NPT - National Pipe Taper thread

ISO 7-�, JIS B0�0� BSPT - British Standard Pipe Taper thread

DIN ��5� BSPP

ANSI B�6.��, EN ��760 Socket weld end connection

ANSI B�6.�5, EN��6�7-� Buttweld end connection (Schedule 5, �0, �0, �0)

ANSI B�6.5, EN �09� Pt �&� Flange dimensions

ANSI B�6.�0, EN 55� Face-to-Face dimensions

NACE MR-0�75, ISO �5�56-�/�/� Materials for use in H�S-containing environments in oil

and gas production

EN ���66-�, API 59�, ANSI FCI 70-� Testing of metallic valves - Pressure tests, test

procedures and acceptance criteria.

Certi�cations API 607, ISO �0�97 Testing of valves - Fire type-testing requirements

PED 97/��/EC Module H Pressure equipment directive

ATEX 9�/9/EC equipment and protective systems intended for use in

potentially explosive atmospheres

(optional for actuated unit only)

IEC 6�50�-� SIL �/� Safety integrity level - Functional safety of electrical/

electronic/programmable electronic safety-related

systems (optional for actuated unit only)

Documentation EN �0�0� �.� / �.� / �.� Metallic materials - types of inspection documents

Metal seated valves GeneralUp to

�00 °C / 75� °F Up to

5�� °C / �000 °FUp to

650 °C / ��00 °FOrdering

code system

Page 3: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

3Metal seated valves

Metal seated valves

General

Valves design

Basic design

Temperature range -60 °C to +�00 °C (-76 °F to +75� °F)

Surface treatment LTPN

Materials Stainless steel A�5� CF�M/CF�M, A�79 ��6/��6L, Carbon steel A��6 WCB, A�05, A�50 LF�

T design

Temperature range -60 °C to +5�� °C (-76 °F to +�000 °F)

Coating HVOF Cr�C� (Chromium Carbide), HVOF WC-Co (Tungsten Carbide) and Stellite

Materials Stainless steel A�5� CF�M/CF�M, A�79 ��6/��6L, carbon steel A��6 WCB, A�05, A�50 LF�

T design

Temperature range -60 °C to +650 °C (-76 °F to +��00 °F)

Coating HVOF Cr�C� (Chromium Carbide)

Materials Stainless steel A�79 ���/���H, A��� F��

Operation Lever or gear operated, pneumatic or electric actuated

Series in range

Z47 / Z47T series Standard and full port

Size range �/�”- �" (DN� - DN50)

Pressure range ANSI Class 600 | Vacuum �0-6 Tor to �0� bar (��90 psi)

Size range ��/�”- �" (DN65 - DN�00)

Pressure range ANSI Class 600 | Vacuum �0-6 Tor to 70 bar (�0�5 psi)

End connections Threaded, welded, �anged

Z73 / Z73T series Full port

Size range �/�”- �” (DN�5 - DN�00)

Pressure range ANSI Class �50 | Vacuum �0-6 Tor to �0 bar (�90 psi)

End connections Flanged

Z74 / Z74T series Full port

Size range �/�”- �” (DN�5 - DN�00)

Pressure range ANSI Class �00 | Vacuum �0-6 Tor to 50 bar (7�5 psi)

End connections Flanged

Z78 / Z78T series Full port

Size range �/�”- �” (DN�5 - DN50)

Pressure range DIN PN�0 | Vacuum �0-6 Tor to �0 bar (5�0 psi)

End connections Flanged

Z77 / Z77T series Full port

Size range �”- �” (DN�0 - DN�00)

Pressure range DIN PN�6 | Vacuum �0-6 Tor to �6 bar (��0 psi)

End connections Flanged

Z28 / Z28T series Standard and full port

Size range �/�”- �” (DN� - DN50)

Pressure range ANSI Class �500 | Vacuum �0-6 Tor to ��� bar (6000 psi)

Size range ��/�”- �” (DN65 - DN�00)

Pressure range ANSI Class �500 | Vacuum �0-6 Tor to �55 bar (�700 psi)

Page 4: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

4

Metal seated valves GeneralUp to

400 °C / 752 °F Up to

538 °C / 1000 °FUp to

650 °C / 1200 °FOrdering

code system

Floating Ball Valves

Metal seated valves

Design features up to 400 °C / 752 °F

Body

• Standard and full port design

• Unidirectional

• High �ow capacity and minimum turbulence

• Fire safe certi�ed to API 607 and ISO �0�97

Ball and metal seats set

• Leak rate to EN���66-� Rate B (factory tested) is achieved

by accurate grinding and lapping processes

• Various surface treatments and coatings available for

superb corrosion and abrasion resistance

• Constant preload of ball/seats set obtained by Inconel 7��

Belleville spring

• Low operating torque

Stem

• Blowout-proof design

• Solid one-piece

• Tight stem-to-ball engagement

• High torque durability

• Live loaded stem seal

Minimum thermal expansion

• One size up and shorter body bolts

• Additional spring washers

Tongue & groove labyrinth design

• Zero leakage into the atmosphere

• Full compression of encapsulated body seal

• Accurate alignment of all parts

pp

�ow direction plate

Variety of surface treatments and coatings to withstand corrosion and wear

Page 5: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

5Metal seated valves

Metal seated valves

General

• Solid cast body and ends

• Standard and full port design

• Accurate alignment of all parts

• High �ow capacity and minimum turbulence

• Fire safe design to API 607 and ISO �0�97

Ball and metal seats set

• Various coatings available for superb corrosion and

abrasion resistance

• Constant preload of ball/seats set obtained by Inconel 7��

Belleville spring

Body seals

• Encapsulated body and bonnet seal guarantees zero

leakage

Bonnet

• Solid extended bonnet allows safe operation at extremely

high temperature

• Remote automatic operator will work under moderate

enviroment conditions

• Low maintenance and operation requirements

• Oversized non-rising extended stem perfectly aligned

durable even under heavy load.

• Broad ball-stem connection allows torque transfer with no

surface compressive deformation

• Two metallic bearings ensures valve stem aligned rotation

• Inconel 7�� thrust bearings eliminate galling of stem and

valve body

Stem seal

• Live loaded expanded graphite stem seal guarantees low

emission

Page 6: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

6

Metal seated valves GeneralUp to Up to Up to Ordering

e system

Floating Ball Valves

Metal seated valves

T Series un

Mate lapp

bearings

at

truction

Body

• Full compliant with ASME B�6.��

• Robust body and bonnet construction from special alloys

• Double the number of shorter bolts reduces thermal

expansion and maintain valve shell integrity even at

elevated temperatures and pressures

• Bolts maintain mechanical properties at temperatures as

high as �00 ̊ C / ��7� ̊ F

• ISO 5��� top platform for easy mounting of actuator and

accessories

Stem

• Perfectly aligned extended stem

• Oversized blow out-proof extended stem capable of

delivering high torque load

• Broad ball-stem connection allows torque transfer with no

surface compression deformation

• Two metallic bearings ensure valve-stem aligned rotation

• Inconel 7�� thrust bearings eliminate galling of stem and

valve body

Ball and metal seats set

• Rigid metallic seats maintain geometric accuracy over

wide ranges of pressure and temperature load

• Leak rate to EN���66-� Rate B (factory tested) is achieved

by accurate grinding and lapping processes

• HVOF coatings available for superb corrosion and abrasion

resistance

• Constant preload of ball/seats set obtained by Inconel 7��

Belleville spring

Page 7: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

A

H

S

C D

B

ø Ball port

ø W

TxL threadF PCD

½�without nut

¾" - 1�with nut

PP

N thread

MStem flatsshow valveball position

Preparationfor actuation

28

Floating Ball Valves

Metal seated valves

Valve dimensions

Metal seated valves GeneralUp to

�00 °C / 75� °F Up to 538 °C /

1000 °FUp to

650 °C / ��00 °FOrdering

code system

Size 1⁄4”- 2” | DN8-DN50 | Class 600 | Z47T Series

Std. port

Full port UnitBall port

AB C D H S W M N P F W TxL

Weightkg/lb

KvCvWelded Threaded

DN15 DN8, DN10 mm ��.�5 ��0.60 66.00 �0.60 ���.�0 �90.�0 ���.�0 �50.00 �6.00 5.50 �/�’’ UNF

7.�0 (F0�) �6.00M5x�0

�.�5 7.0

1/2” 1/4”, 3/8” inch 0.�� 5.5� �.60 0.�� 7.�� 7.�9 �.�� 5.9� �.�� 0.�� 0.�� �.�� �.97 6.0

DN20 DN15 mm ��.�0 ��6.95 70.60 ��.55 ���.�0 �9�.�0 ��6.�0 �50.00 5�.�0 5.50 �/�’’ UNF

7.�0 (F0�) �6.00M5x�0

�.55 �0.0

3/4” 1/2” inch 0.56 5.79 �.7� 0.97 7.�� 7.57 �.5� 5.9� �.05 0.�� 0.�� �.�� �.�� �.6

DN25 DN20 mm �0.65 �6�.75 9�.00 ��.75 �90.�0 �07.90 ���.�0 ��0.00 60.50 7.5� 7/�6’’ UNF

7.�0 (F0�) ��.00M5x�0

�.�5 ��.0

1" 3/4” inch 0.�� 6.6� �.70 �.�5 7.50 �.�9 9.�� 9.06 �.�� 0.�0 0.�� �.65 6.�7 ��.�

DN32 DN25 mm �5.50 �79.�5 �0�.50 ��.�5 �95.�0 ���.90 ��6.�0 ��0.00 69.00 7.5� 7/�6’’ UNF

7.�0 (F0�) ��.00M5x�0

�.55 �9.0

11/4" 1" inch �.00 7.06 �.�7 �.6� 7.69 �.�� 9.�� 9.06 �.7� 0.�0 0.�� �.65 7.�� ��.�

DN40 DN32 mm ��.�0 ��9.�0 ��6.00 ��.�0 �95.�0 ���.90 ���.�0 ��7.00 79.�0 �.7� 9/�6’’ UNF

�.00 (F05) 50.00M6x��

�.50 7�.0

11/2" 11/4" inch �.�5 7.�6 �.57 �.9� 7.69 �.�5 9.7� 9.�� �.�� 0.�� 0.�� �.97 9.90 6�.�

DN50 DN40 mm ��.�0 �00.�0 ���.00 56.�0 �00.�0 ��9.90 �5�.�0 ��7.00 90.70 �.7� 9/�6’’ UNF

�.00 (F05) 50.00M6x��

6.00 �0�.0

2" 11/2" inch �.50 7.�9 5.0� �.�� 7.�9 9.05 9.9� 9.�� �.57 0.�� 0.�� �.97 ��.�0 �9.7

Page 8: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

5A

5B5C

1

2B6

22

7

18

6A6

2A18

25

24

13

4

11

15

9

17

16

3

16

17

10

8

26

29

29Metal seated valves

Components & materials

Metal seated valves

Size 1⁄4”- 2” | DN8-DN50 | Class 600 | Z47T Series

Item Description Material speci�cation Qty.

9* Stem seal Graphite �

10 Follower B7�� ��6L �

11 Disc spring A69� 6�� �7-7PH �

12 Stem nut A�9� �M, EN�506-� A�-�0 �

13 Locking clip A�6� �, �A �

14 Handle A659 G�0�00 Zinc plate, A��0 ��0 �

15 Serrated washer A�9� 6 �

16 Handle nut A�9� �M, EN�506-� A�-�0 �

17 Sleeve PVC �

18 Body bolts A�9� B�M, A�9� B7 zinc plated,A5�� 660 �

22 Arrow �ow A�67 �0� �

23 Tag (not shown) A�67 �0� �

24 Bonnet seal Graphite �

25 Stem Bearing B6�7 N077�� Inconel 7�� , Bonze �

26 Bonnet A�5� CF�M, A�79 ���, A�79 ���H �

29 Bonnet bolts A�9� B�M, A5�� 660 �

* Repair kit components** Other coatings avilableWC-Co - Tungsten Carbide with Cobalt binder (HVOF), Stellite (PTA)

Item Description Material speci�cation Qty.

1 Body A�5� CF�M, A��6 WCB, A�05 �

2A Downstream end A�5� CF�M, A��6 WCB, A�05 , A�79 ��� �

2B Upstream end A�5� CF�M, A��6 WCB, A�05 , A�79 ��� �

3Ball Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

4 Stem B6�7 N077�� Inconel 7�� �

5ADownstream seat Base material: A��� F��6, A��� F��6H,

A��� F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5BUpstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5C Upstream seat spring Inconel 7�� �

6* Body seal Graphite �

6A* Seat seal Graphite �

7*Stem thrust seal A�79 ��6L, Hardended with LTPN - Low

Temperature Plasma carboNitriding technology. B6�7 N077�� Inconel 7��

8 Stop pin A5�� �0� �

Page 9: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

A

B

H

C D

S

ø Ball port

ø W

TxL threadF PCD

30

Floating Ball Valves

Metal seated valves

Valve dimensions

Size 21⁄2”- 8” | DN65-DN200 | Class 600 | Z47T Series

Metal seated valves GeneralUp to

�00 °C / 75� °F Up to

538 °C / 1000 °FUp to

650 °C / ��00 °FOrdering

code system

Std. port

Full port UnitBall port

AB C D H S W M

M (DD)

Q N P F TxLWeightkg/lb

Kv

Welded Threaded Cv

DN65 DN50 mm 5� �00 �60.00 75 ��9.90 ��6.�0 ��6.�0 �0� �50 ��.90 �5.90 ��.70 �"-�� UNF-�A

�6.70 (F�0) �0�.00M�0x��

�9.� 69

21/2” 2" inch �.0� 7.�7 6.�0 �.95 9.�� ��.�� ��.�5 �5.79 5.9� 0.7� 0.6� 0.�9 0.66 �.0� ��.� �0

DN80 DN65 mm 6�.75 ��5.00 ���.00 �0�.�0 �66.50 ���.00 �5�.50 600.00 �9�.50 ��.90 �5.90 ��.70 �"-�� UNF-�A

�6.70 (F�0) �0�.00M�0x��

�0.0 �0�

3" 21/2” inch �.5� ��.�� �.�9 �.�� �0.�9 ��.�� ��.9� ��.6� 7.5� 0.7� 0.6� 0.�9 0.66 �.0� 66.0 ��0

DN100 DN80 mm �0 �56 - ��0 �7�.90 ���.00 - - ��0 ��.�5 ��.75 �5.�0 ��/�’’ -�� UNF-�A

�6.�0 (F��) ��5.00M��x�6

�6.0 ��0

4" 3" inch �.�5 ��.0� - �.�� �0.9� ��.70 - - �.�7 �.�� 0.9� �.�9 �.0� �.9� �0�.� �56

DN150 DN100 mm �00 �00.00 - ��5 �9�.�0 �6�.00 - - �60 ��.�5 ��.75 �5.�0 ��/�’’ -�� UNF-�A

�6.�0 (F��) ��5.00M��x��

6�.0 ��5

6" 4" inch �.9� �5.75 - 5.�� ��.6� ��.�� - - �0.�� �.�� 0.9� �.�9 �.0� �.9� ��9.6 �50

DN200 DN150 mm �50 �90 - �90 �97.�0 5�0.00 - - �60 �5.90 ��.75 �5.�0�" UN-�A

�0.00 (F��) ��5.00M�6x��

���.0 6�5

8" 6" inch 5.9� �9.�9 - 7.�� �5.6� �0.0� - - ��.�7 �.�� 0.9� �.�9 �.57 5.7� ��5.6 7�0

DN200 mm �00 500 - �75 �99.00 65�.00 - - �70 �5.90 �5.90 �6.50 ��/�’’ UN-�A

50.00 (F�6) �65.00M�0x��

��0.0 �7�

8" inch 7.�7 �9.69 - �0.�� �9.65 �5.75 - - ��.50 �.�� �.�� �.�� �.97 6.50 ��6.0 �0�0

(-) Due to high valve torque pipe handle cannot be used. A manual gear or automation means should be used to operate the valve.

Page 10: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

2A

18

6A

5A

3

6

27

18

5C

6

24

1

5B

25

22

22

7

9

1014A

13

12

14 14B 14C

26

29

8

16

31Metal seated valves

Components & materials

Metal seated valves

Size 21⁄2”- 8” | DN65-DN200 | Class 600 | Z47T Series

Item Description Material speci�cation Qty.

9* Stem seal Graphite �

10 Follower B7�� ��6L �

11 Disc spring A69� 6�� �7-7PH �

12 Stem nut A�9� �M, EN�506-� A�-�0 �

13 Tab lock washer A��0 �0� �

14 Handle C.St. A�9 G�0�00 Zinc plate, A��0 ��0 �

14A Stop plate C.St. �.0�0� Zinc plate, A��0 ��0 �

14BWrench head Ductile Iron A5�6 Gr. 65-�5-��, A��6 WCB,

A�5� CF�M�

16 Wrench bolt EN�506-� A�-70/A�-�0, A�9� Gr B�/B�M �

17 Sleeve PVC �

18 Body bolts A�9� B�M, A�9� B7 zinc plated, A5�� 660 �0-��22 Arrow �ow A�67 �0� �

23 Tag (not shown) A�67 �0� �

24 Bonnet seal Graphite �

25 Stem Bearing B6�7 N077�� Inconel 7�� , Bonze �

26 Bonnet A�5� CF�M, A�79 ���, A�79 ��6H �

29 Bonnet bolts A�9� B�M, A5�� 660 �-6* Repair kit components** Other coatings avilableWC-Co - Tungsten Carbide with Cobalt binder (HVOF), Stellite (PTA)

Item Description Material speci�cation Qty.

1 Body A�5� CF�M, A��6 WCB �

2A Downstream end A�5� CF�M, A��6 WCB, A�79 ��� �

2B Upstream end A�5� CF�M, A��6 WCB, A�79 ��� �

3Ball Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

4 Stem B6�7 N077�� Inconel 7�� �

5ADownstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5BUpstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5C Upstream seat spring Inconel 7�� �

6* Body seal Graphite �

6B* Seat seal Graphite �

7*Stem thrust seal A�79 ��6L, Hardended with LTPN - Low

Temperature Plasma carboNitriding technology. B6�7 N077�� Inconel 7��

8 Stop pin A5�� �0� �

Page 11: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

A

H

S

C D

B

ø Ball port

ø W

TxL threadF PCD

½�without nut

¾" - 1�with nut

PP

N thread

MStem flatsshow valveball position

Preparationfor actuation

32

Floating Ball Valves

Metal seated valves

Valve dimensions

Size 1”- 11⁄2” | DN25-DN40 | Class 150/300 | Z73T/Z74T Series

Metal seated valves GeneralUp to

�00 °C / 75� °F Up to

538 °C / 1000 °FUp to

650 °C / ��00 °FOrdering

code system

Std. port

UnitBall port

A BC D H S

W M N P F TxL

Weight kg/lb Kv

150 300 150 300 150 300 150 300 Cv

DN25 mm �5.�0 ��7.00 �65.00 55.00 7�.00 �95.00 ���.00 ��6.50 ��0.00 �0�.00 �56.00 7.5�7/�6’’ UNF

7.�0 (F0�) ��.00M5x�0

6.5 �.0 ��5

1” inch �.00 5.00 6.50 �.�7 �.�7 7.6� �.�9 9.�� 9.06 �.�5 - 0.�0 0.�� �.65 ��.� �7.6 �75

DN40 mm ��.�0 �65.00 �90.00 6�.00 �0.�0 �0�.00 ��0.60 �76.�0 ��7.00 ��7.00 �65.00 �.7�9/�6’’ UNF

�.50 (F05) 50.00M6x��

�.5 ��.5 ���

11/2” inch �.50 6.50 7.�� �.6� �.�7 7.9� 9.0� �0.90 9.�� 5.00 - 0.�� 0.�� �.97 ��.7 �5.� 50�

Use Z�7T valve series for sizes ½" (DN�5) and ¾" (DN�0)

Page 12: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

5A

5B

5C

1

6A

22

7

18

3

6

2

25

24

13

4

11

15

9

17

16

19

16

17

10

8

26

29

33Metal seated valves

Components & materials

Metal seated valves

Size 1”- 11⁄2” | DN25-DN40 | Class 150/300 | Z73T/Z74T Series

Item Description Material speci�cation Qty.

8 Stop pin A5�� �0� �

9* Stem seal Graphite �

10 Follower B7�� ��6L �

11 Disc spring A69� 6�� �7-7PH �

12 Stem nut A�9� �M, EN�506-� A�-�0 �

13 Locking clip A�6� �, �A �

14 Handle A659 G�0�00 Zinc plate, A��0 ��0 �

15 Serrated washer A�9� 6 �

16 Handle nut A�9� �M, EN�506-� A�-�0 �

17 Sleeve PVC �

18 Body bolts/studs A�9� B�M, A�9� B7 zinc plated,A5�� 660 �

19 Body nuts A�9� B�, A�9� 7 zinc plated,A5�� 660 �

22 Arrow �ow A�67 �0� �

23 Tag (not shown) A�67 �0� �

24 Bonnet seal Graphite �

25 Stem Bearing B6�7 N077�� Inconel 7�� , Bonze �

26 Bonnet A�5� CF�M, A�79 ���, A�79 ��6H �

29 Bonnet bolts A�9� B�M, A5�� 660 �-6* Repair kit components** Other coatings avilableWC-Co - Tungsten Carbide with Cobalt binder (HVOF), Stellite (PTA)

Item Description Material speci�cation Qty.

1 Body A�79, ��6L, A�79 ���, A�50 LF�, A�5� CF�M, A��6 WCB �

2 end A�79, ��6L, A�79 ���, A�50 LF�, A�5� CF�M, A��6 WCB �

3Ball Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

4 Stem B6�7 N077�� Inconel 7�� �

5ADownstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5BUpstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5C Upstream seat spring Inconel 7�� �

6* Body seal Graphite �

6A* Seat seal Graphite �

7*Stem thrust seal A�79 ��6L, Hardended with LTPN - Low

Temperature Plasma carboNitriding technology. B6�7 N077�� Inconel 7��

Page 13: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

ø W

TxL threadF PCD

A

D C

H

S

B

ø Ball port

Preparationfor actuation

P

DD

Stem grooveshows valveball position

Square

N thread N thread

Q M M

M

34

Floating Ball Valves

Metal seated valves

Valve dimensions

Size 2”- 8” | DN50-DN200 | Class 150/300 | Z73T/Z74T Series

Metal seated valves GeneralUp to

�00 °C / 75� °F Up to

538 °C / 1000 °FUp to

650 °C / ��00 °FOrdering

code system

Std. port

UnitBall port

A BC D H S

WM

M DD

Q N P F TxLWeight kg/lb Kv

150 300 150 300 150 300 150 300 Cv

DN50 mm 5��7�.00 ��6.00 69.00 75.�0 ���.�0 �6�.�0 �90.00 �56.00 ��7.00 ��7.00 - ��.90 �0.00M�0X�.5

�7.00 (F07) 70.00M�x��

��.5 �5.5 ��5

2” inch �.0� 7.0� �.50 �.7� �.96 �.77 �0.�� ��.�� �0.0� 5.00 5.00 - 0.55 0.79 0.67 �.76 �9.7 ��.� �75

DN80 mm �0 �0�.00 ���.50 77.50 96.�0 �60.�0 �07.00 ��7.�0 �0�.00 �90.50 ��0.00 ��.90 �5.90 ��.70 �"-�� UNF-�A

�6.70 (F�0) �0�.00M�0x��

�5 �� ����

3” inch �.�5 7.99 ��.�� �.05 �.�0 �0.�5 ��.09 ��.67 �5.79 7.50 �.�7 0.7� 0.6� 0.�9 0.�� �.0� 55.0 70.� ��00

DN100 mm �00 ���.50 �0�.�0 ��.50 �0�.50 �76.�0 ���.00 - - ��0.00 �5�.00 ��.�5 ��.75 �5.�0 ��/�’’-�� UNF-�A

�6.�0 (F�0) �0�.00M��x�6

�5 50.0 �50�

4" inch �.9� 9.00 ��.00 �.�� �.�� �0.�� ��.7� - - 9.06 �0.00 �.�� 0.9� �.�9 �.0� �.0� 99.0 ��0.0 ��00

DN150 mm �50 �9�.00 �0�.50 �6�.50 �7�.50 ���.�0 �5�.70 - - ���.00 ���.00 ��.�5 ��.75 �5.�0 ��/�’’-�� UNF-�A

�6.�0 (F��) ��5.00M��x��

90 ��0 �6�5

6" inch 5.9� �5.5� �5.�9 6.�� 6.�7 �5.05 �7.7� - - ��.9� ��.9� �.�� 0.9� �.�9 0.�� �.9� �9�.0 ���.0 5�00

DN200 mm �00 �57.�0 50�.65 ���.50 ��0.70 �95.50 60�.�0 - - ���.00 ���.00 �5.90 ��.75 �5.�0�" UN-�A

�0.00 (F��) ��5.00M�6x��

��0 ��5 76�9

8” inch 7.�7 ��.00 �9.75 9.55 9.�� �9.5� ��.9� - - ��.50 �5.00 �.�� 0.9� �.�9 0.�� 5.7� �6�.0 5�9.0 9�00

(-) Due to high valve torque pipe handle cannot be used. A manual gear or automation means should be used to operate the valve.

Page 14: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

2

18

6A

Preparationfor actuation

11

3

6

5A

5B

5C

1

22

4

7

9

1014A

1312

14 14B 14C

26

29

8

24

25

16

35Metal seated valves

Components & materials

Metal seated valves

Size 2”- 8” | DN80-DN200 | Class 150/300 | Z73T/Z74T Series

Item Description Material speci�cation Qty.

9* Stem seal Graphite �

10 Follower B7�� ��6L �

11 Disc spring A69� 6�� �7-7PH �

12 Stem nut A�9� �M, EN�506-� A�-�0 �

13 Tab lock washer A��0 �0� �

14 Handle C.St. A�9 G�0�00 Zinc plate, A��0 ��0 �

14A Stop plate C.St. �.0�0� Zinc plate, A��0 ��0 �

14BWrench head Ductile Iron A5�6 Gr. 65-�5-��, A��6 WCB,

A�5� CF�M�

16 Wrench bolt EN�506-� A�-70/A�-�0, A�9� Gr B�/B�M �

17 Sleeve PVC �

18 Body bolts A�9� B�M, A�9� B7 zinc plated, A5�� 660 �-��22 Arrow �ow A�67 �0� �

23 Tag (not shown) A�67 �0� �

24 Bonnet seal Graphite �

25 Stem Bearing B6�7 N077�� Inconel 7�� , Bonze �

26 Bonnet A�5� CF�M, A�79 ���, A�79 ��6H �

29 Bonnet bolts A�9� B�M, A5�� 660 �-6* Repair kit components** Other coatings avilableWC-Co - Tungsten Carbide with Cobalt binder (HVOF), Stellite (PTA)

Item Description Material speci�cation Qty.

1 Body A�5� CF�M, A��6 WCB �

2 end A�5� CF�M, A��6 WCB �

3Ball Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

4 Stem B6�7 N077�� Inconel 7�� �

5ADownstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5BUpstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5C Upstream seat spring Inconel 7�� �

6* Body seal Graphite �

6A* Seat seal Graphite �

7*

Stem thrust seal A�79 ��6L, Hardended with LTPN - Low Temperature Plasma carboNitriding technology.B6�7 N077�� Inconel 7��

8 Stop pin A5�� �0� �

Page 15: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

A

H

S

C D

B

ø Ball port

ø W

TxL threadF PCD

½�without nut

¾" - 1�with nut

PP

N thread

MStem flatsshow valveball position

Preparationfor actuation

36

Floating Ball Valves

Metal seated valves

Valve dimensions

Size 1”- 11⁄2” | DN25-DN40 | PN40 | Z78T Series

Metal seated valves GeneralUp to

�00 °C / 75� °F Up to

538 °C / 1000 °FUp to

650 °C / ��00 °FOrdering

code system

Std. port

UnitBall port

AB C D H S W M N P F TxL

Weight kg/lb Kv

F1 F4 F1 F4 Cv

DN25 mm �5.50�60.00 - 50.50�95.00���.00��6.50��0.00��5.00 7.507/�6’’ UNF

7.�0 (F0�) ��.00M5x�0

7.0 - ��5

1” inch �.00 6.�0 - �.99 7.6� �.�9 9.�� 9.06 �.5� 0.�0 0.�� �.65 �5.� - �75

DN40 mm ��.�0�00.00��0.00 76.00�0�.00��0.60�76.�0��7.00�50.00 �.679/�6’’ UNF

�.50 (F05) 50.00M6x��

��.0 �.0 ���

11/2” inch �.50 7.�7 5.5� �.99 7.9� 9.0� �0.90 9.�� 5.9� 0.�� 0.�� �.97 �6.� �7.6 50�

Use Z�7T valve series for sizes ½" (DN�5) and ¾" (DN�0)

Page 16: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

5A

5B

5C

1

6A

22

7

18

3

6

2

25

24

13

4

11

15

9

17

16

19

16

17

10

8

26

29

37Metal seated valves

Components & materials

Metal seated valves

Size 1”- 11⁄2” | DN25-DN40 | PN40 | Z78T Series

Item Description Material speci�cation Qty.

8 Stop pin A5�� �0� �

9* Stem seal Graphite �

10 Follower B7�� ��6L �

11 Disc spring A69� 6�� �7-7PH �

12 Stem nut A�9� �M, EN�506-� A�-�0 �

13 Locking clip A�6� �, �A �

14 Handle A659 G�0�00 Zinc plate, A��0 ��0 �

15 Serrated washer A�9� 6 �

16 Handle nut A�9� �M, EN�506-� A�-�0 �

17 Sleeve PVC �

18 Body bolts/studs A�9� B�M, A�9� B7 zinc plated,A5�� 660 �

19 Body nuts A�9� B�, A�9� 7 zinc plated,A5�� 660 �

22 Arrow �ow A�67 �0� �

23 Tag (not shown) A�67 �0� �

24 Bonnet seal Graphite �

25 Stem Bearing B6�7 N077�� Inconel 7�� , Bonze �

26 Bonnet A�5� CF�M, A�79 ���, A�79 ��6H �

29 Bonnet bolts A�9� B�M, A5�� 660 �

* Repair kit components** Other coatings avilableWC-Co - Tungsten Carbide with Cobalt binder (HVOF), Stellite (PTA)

Item Description Material speci�cation Qty.

1 Body A�79, ��6L, A�79 ���, A�50 LF�, X�CrNiMo �7 �� � (�.��0�), GS-C�5 (DIN�.06�9 �

2 end A�79, ��6L, A�79 ���, A�50 LF�, X�CrNiMo �7 �� � (�.��0�), GS-C�5 (DIN�.06�9 �

3Ball Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

4 Stem B6�7 N077�� Inconel 7�� �

5ADownstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5BUpstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF)."

5C Upstream seat spring Inconel 7�� �

6* Body seal Graphite �

6A* Seat seal Graphite �

7*

Stem thrust seal A�79 ��6L, Hardended with LTPN - Low Temperature Plasma carboNitriding technology. B6�7 N077�� Inconel 7��

Page 17: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

ø W

TxL threadF PCD

A

D C

H

S

B

ø Ball port

Preparationfor actuation

P

DD

Stem grooveshows valveball position

Square

N thread N thread

Q M M

M

38

Floating Ball Valves

Metal seated valves

Valve dimensions

Metal seated valves GeneralUp to

�00 °C / 75� °F Up to

538 °C / 1000 °FUp to

650 °C / ��00 °FOrdering

code system

Std. port

UnitBall port

A B C D H S W MM

(DD)Q N P F TxL

Weight kg/lb

Cv

DN50 mm 5��50.00 69.00 ���.�0 �6�.�0 �90.00 �56.00 �65.00 - ��.90 �0.00M�0X�.5

�7.00 (F07) 70.00M�x��

��.5 ��5

2” inch �.0� 5.9� �.7� �.77 �0.�� ��.�� �0.0� 6.50 - 0.55 0.79 0.67 �.76 �7.5 �75

DN80 mm �0 ��0.00 77.50 �60.�0 �07.00 ��7.�0 �0�.00 �00.00 ��.90 �5.90 ��.70 �’’-�� UNF-�A

�6.70 (F�0) �0�.00M�0x��

��.0 ����

3” inch �.�5 7.09 �.05 �0.�5 ��.09 ��.67 �5.79 7.�7 0.7� 0.6� 0.�9 0.�� �.0� 6�.� ��00

DN100 mm �00 �90.00 ��.50 �76.�0 ���.00 - - ��0.00 ��.�5 ��.75 �5.�0 ��/�’’-�� UNF-�A

�6.�0 (F�0) �0�.00M��x�6

�5.0 �50�

4" inch �.9� 7.�� �.�� �0.�� ��.7� - - �.66 �.�� 0.9� �.�9 �.0� �.0� 99.0 ��00

DN150 mm �50 �50.00 �6�.50 ���.�0 �5�.70 - - ��5.00 ��.�5 ��.75 �5.�0 ��/�’’-�� UNF-�A

�6.�0 (F��) ��5.00M��x��

�00.0 �6�5

6” inch 5.9� ��.7� 6.�� �5.05 �7.7� - - ��.�� �.�� 0.9� �.�9 0.�� �.9� ��0.0 5�00

Size 2” | DN50 | PN40 | Z78T Series Size 3”- 6” | DN80-DN150 | PN16 | Z77T Series

(-) Due to high valve torque pipe handle cannot be used. A manual gear or automation means should be used to operate the valve.

Page 18: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

2

18

6A

Preparationfor actuation

11

3

6

5A

5B

5C

1

22

4

7

9

1014A

1312

14 14B 14C

26

29

8

24

25

16

39Metal seated valves

Components & materials

Metal seated valves

Size 2” | DN50 | PN40 | Z78T Series Size 3”- 6” | DN80-DN150 | PN16 | Z77T Series

Item Description Material speci�cation Qty.

8 Stop pin A5�� �0� �

9* Stem seal Graphite �

10 Follower B7�� ��6L �

11 Disc spring A69� 6�� �7-7PH �

12 Stem nut A�9� �M, EN�506-� A�-�0 �

13 Tab lock washer A��0 �0� �

14 Handle C.St. A�9 G�0�00 Zinc plate, A��0 ��0 �

14A Stop plate C.St. �.0�0� Zinc plate, A��0 ��0 �

14BWrench head Ductile Iron A5�6 Gr. 65-�5-��, A��6 WCB,

A�5� CF�M�

16 Wrench bolt EN�506-� A�-70/A�-�0, A�9� Gr B�/B�M �

17 Sleeve PVC �

18 Body bolts A�9� B�M, A�9� B7 zinc plated, A5�� 660 �-��22 Arrow �ow A�67 �0� �

23 Tag (not shown) A�67 �0� �

24 Bonnet seal Graphite �

25 Stem Bearing B6�7 N077�� Inconel 7�� , Bonze �

26 Bonnet A�5� CF�M, A�79 ���, A�79 ��6H �

29 Bonnet bolts A�9� B�M, A5�� 660 �-6* Repair kit components** Other coatings avilableWC-Co - Tungsten Carbide with Cobalt binder (HVOF), Stellite (PTA)

Item Description Material speci�cation Qty.

1 Body X�CrNiMo �7 �� � (�.��0�), GS-C�5 (DIN�.06�9) �

2 end X�CrNiMo �7 �� � (�.��0�), GS-C�5 (DIN�.06�9) �

3Ball Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

4 Stem B6�7 N077�� Inconel 7�� �

5ADownstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5BUpstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating**: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5C Upstream seat spring Inconel 7�� �

6* Body seal Graphite �

6A* Seat seal Graphite �

7*

Stem thrust seal "A�79 ��6L, Hardended with LTPN - Low Temperature Plasma carboNitriding technology. B6�7 N077�� Inconel 7��"

Page 19: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

ø W

TxL threadF PCD

S

D

C

H

B

A

ø Ball port

½�without nut

¾" - 1�with nut

PP

N thread

MStem flatsshow valveball position

Preparationfor actuation

40

Floating Ball Valves

Metal seated valves

Valve dimensions

Size 1⁄4”- 11⁄4” | DN8-DN32 | Class 600 | Z47T Series

Metal seated valves GeneralUp to

�00 °C / 75� °F Up to

5�� °C / �000 °FUp to 650 °C /

1200 °FOrdering

code system

Std. port

Full port UnitBall port

AB C D H S W M N P F W TxL

Weightkg/lb

KvCvWelded Threaded

DN15 DN8, DN10 mm ��.�5 �59.00 9�.00 �5.00 ���.00 �9�.00 ��6.00 �50.00 69.50 5.50 �/�’’ UNF

7.�0 (F0�) �6.00M5x�

�.� 7.0

1/2” 1/4”, 3/8” inch 0.�� 6.�6 �.6� �.�� 7.�7 7.5� �.50 5.9� �.7� 0.�� 0.�� �.�� 9.5 6.0

DN20 DN15 mm ��.00 �69.00 �00.00 �0.00 ��7.00 �0�.50 ��9.00 ��0.00 9�.00 7.5� 7/�6’’ UNF

7.�0 (F0�) ��.00M5x�

5.0 �0.0

3/4” 1/2” inch 0.5� 6.65 �.9� �.57 7.�6 �.05 9.0� 9.06 �.�6 0.�0 0.�� �.65 ��.0 �.6

DN25 DN20 mm �0.65 �90.00 ��5.00 �9.00 �96.50 ��6.00 �5�.00 ��7.00 �09.00 �.70 9/�6’’ UNF

7.�0 (F05) 50.00M6x�

�0.5 ��.0

1" 3/4” inch 0.�� 7.�� �.9� �.9� 7.7� �.90 9.9� 9.�� �.�9 0.�� 0.�� �.97 ��.� ��.�

DN32 DN25 mm �9�.00 ��7.00 ���.00 �9.00 �0�.50 ���.00 �60.00 ��7.00 ���.00 �.70 9/�6’’ UNF

7.�0 (F05) 50.00M6x�

��.0 �9.0

11/4" 1" inch 7.60 7.�6 5.�� �.9� �.05 9.�7 �0.�� 9.�� 5.0� 0.�� 0.�� �.97 ��.6 ��.�

Page 20: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

17

12

14

15

9

11

16

10

13

25

24

4

7

2A

6A

5C

18

1

5A

5B22

18

6

6

2B

26

8

29

3

41Metal seated valves

Components & materials

Metal seated valves

Size 1⁄4”- 11⁄4” | DN8-DN32 | Class 600 | Z47T Series

Item Description Material speci�cation Qty.

8 Stop pin A5�� �0� �

9* Stem seal Graphite �

10 Follower B7�� ��6L �

11 Disc spring A69� 6�� �7-7PH �

12 Stem nut A�9� �M, EN�506-� A�-�0 �

13 Locking clip A�6� �, �A �

14 Handle A659 G�0�00 Zinc plate, A��0 ��0 �

15 Serrated washer A�9� 6 �

16 Handle nut A�9� �M, EN�506-� A�-�0 �

17 Sleeve PVC �

18 Body bolts A�9� B�M, A�9� B7 zinc plated,A5�� 660 �

22 Arrow �ow A�67 �0� �

23 Tag (not shown) A�67 �0� �

24 Bonnet seal Graphite �

25 Stem Bearing B6�7 N077�� Inconel 7�� , Bonze �

26Bonnet A�79 ��6H, A�79 ���H, B6�7 N077��

Inconel 7���

29 Bonnet bolts A�9� B�M, A5�� 660 �

* Repair kit components

Item Description Material speci�cation Qty.

1 Body A�79 ��6H, A�79 ���H, A��� F��, B6�7 N077�� Inconel 7�� �

2A Downstream end A�79 ��6H, A�79 ���H, A��� F��, B6�7 N077�� Inconel 7�� �

2B Upstream end A�79 ��6H, A�79 ���H, A��� F��, B6�7 N077�� Inconel 7�� �

3Ball Base material: A��� F��6, A��� F��6H, A���

F6A Coating: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

4 Stem B6�7 N077�� Inconel 7�� �

5ADownstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5BUpstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF).

5C Upstream seat spring Inconel 7�� �

6* Body seal Graphite �

6A* Seat seal Graphite �

7*Stem thrust seal "A�79 ��6L, Hardended with LTPN - Low

Temperature Plasma carboNitriding technology. B6�7 N077�� Inconel 7��"

Page 21: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

A

B

S

DC

H

ø Ball port

ø W

TxL threadF PCD

Preparationfor actuation

P

DD

Stem grooveshows valveball position

Square

N thread N thread

Q M M

M

42

Floating Ball Valves

Metal seated valves

Valve dimensions

Size 11⁄2”- 6” | DN40-DN150 | Class 600 | Z47T Series

Metal seated valves GeneralUp to

�00 °C / 75� °F Up to

5�� °C / �000 °FUp to

650 °C / 1200 °FOrdering

code system

Std. port

Full port

UnitBall port

AB C D H S W M M DD Q N P F W TxL

Weightkg/lb

Kv

Welded Threaded Cv

DN40 DN32 mm ��.�0 ��7.00 �5�.00 70.00 �05.�0 ��7.�0 ���.00 �0���5.00 - ��.90 �0.00M�0x�.5

��.�5 (F07) 70.00M�x�0

�5 69

11/2” 11/4” inch �.�5 9.�� 6.06 �.76 �.�0 9.7� ��.�� �5.79 5.7� - 0.55 ��.00 0.5� �.76 55.0 �0

DN50 DN40 mm ��.�0 ���.00 �57.00 70.00 �57.�0 �99.�0 ��5.00 600.00 ��5.00 - ��.90 �0.00M�0x�.5

��.�5 (F07) 70.00M�x�0

50 �0�

2" 11/2” inch �.50 9.�9 6.�� �.76 �0.�5 ��.79 ��.�9 ��.6� �.�6 - 0.55 ��.00 0.5� �.76 ��0.0 ��0

DN65 DN50 mm 5� �0�.00 �9�.00 9�.00 �75.00 ���.50 ���.50 �0�.00 ��0.00 ��.90 �5.90 ��.70 �"-�� UNF-�A

��.50 (F�0) �0�.00M�0x��

�0 ��0

21/2” 2" inch �.0� ��.�9 7.6� �.70 �0.�� ��.56 �5.�� �5.79 9.�5 0.7� 0.6� 0.�9 0.7� �.0� �76.0 �56

DN80 DN65 mm 6�.75 �7�.00 �5�.00 ��5.00 �9�.�0 �6�.�0 �0�.�0 600.00 �65.00 ��.�5 ��.75 �5.�0 ��/�"-�� UNF-�A

��.�0 (F��) ��5.00M��x��

��5 ��5

3" 21/2” inch �.5� ��.�� �0.00 �.5� ��.5� ��.�6 �5.�� ��.6� �0.�� �.�� 0.9� �.�9 0.95 �.9� �75.0 �50

DN100 DN80 mm �0 ��0.00 - ��0.00 �95.00 507.70 - - ��0.00 ��.�5 ��.75 �5.�0 ��/�"-�� UNF-�A

��.�0 (F��) ��0.00M�6x�0

�75 6�5

4" 3" inch �.�5 �6.�� - 5.�� �5.55 �9.99 - - ��.�0 �.�� 0.9� �.�9 0.95 5.5� ��5.0 7�0

DN150 DN100 mm �00 5�0.00 - �75.00 ��0.00 ���.00 - - �95.00 �5.90 �5.90 ��.50�" UN-�A

�0.00 (F�6) �65.00M�0x�5

��5 �7�

6" 4" inch �.9� �0.0� - 6.�9 ��.90 ��.06 - - �5.55 �.�� �.�� �.7� �.�� 6.50 957.0 �0�0

(-) Due to high valve torque pipe handle cannot be used. A manual gear or automation means should be used to operate the valve.

Page 22: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

17

25

24

4

7

2A

6A

5C

18

1

5A

5B

22

18

6

6

2B

3

26

8

29

12

17C17A

9

14A

14

10

13

Preparationfor actuation

11

43Metal seated valves

Components & materials

Metal seated valves

Size 11⁄2”- 6” | DN40-DN150 | Class 600 | Z47T Series

Item Description Material speci�cation Qty.

8 Stop pin A5�� �0� �

9* Stem seal Graphite �

10 Follower B7�� ��6L �

11 Disc spring A69� 6�� �7-7PH �

12 Stem nut A�9� �M, EN�506-� A�-�0 �

13 Tab lock washer A��0 �0� �

14 Handle C.St. A�9 G�0�00 Zinc plate, A��0 ��0 �

14A Stop plate C.St. �.0�0� Zinc plate, A��0 ��0 �

14B Wrench head Ductile Iron A5�6 Gr. 65-�5-��, A��6 WCB, A�5� CF�M �

16 Wrench bolt EN�506-� A�-70/A�-�0, A�9� Gr B�/B�M �

17 Sleeve PVC �

18 Body bolts A�9� B�M, A�9� B7 zinc plated, A5�� 660 �0-��

22 Arrow �ow A�67 �0� �

23 Tag (not shown) A�67 �0� �

24 Bonnet seal Graphite �

25 Stem Bearing B6�7 N077�� Inconel 7�� , Bonze �

26 Bonnet A�79 ��6H, A�79 ���H,B6�7 N077�� Inconel 7�� �

29 Bonnet bolts A�9� B�M, A5�� 660 �-6

* Repair kit components

Item Description Material speci�cation Qty.

1 Body A�79 ��6H, A�79 ���H, A��� F��, B6�7 N077�� Inconel 7�� �

2A Downstream end A�79 ��6H, A�79 ���H, A��� F��, B6�7 N077�� Inconel 7�� �

2B Upstream end A�79 ��6H, A�79 ���H, A��� F��, B6�7 N077�� Inconel 7�� �

3Ball Base material: A��� F��6, A��� F��6H, A���

F6A Coating: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF)

4 Stem B6�7 N077�� Inconel 7�� �

5ADownstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF)."

5BUpstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF)."

5C Upstream seat spring Inconel 7�� �

6* Body seal Graphite �

6B* Seat seal Graphite �

7*Stem thrust seal "A�79 ��6L, Hardended with LTPN - Low

Temperature Plasma carboNitriding technology. B6�7 N077�� Inconel 7��"

Page 23: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

ø W

TxL threadF PCD

A

H

S

C D

B

ø Ball port

½�without nut

¾" - 1�with nut

PP

N thread

MStem flatsshow valveball position

Preparationfor actuation

44

Floating Ball Valves

Metal seated valves

Valve dimensions

Size 1⁄4”- 11⁄4” | DN8-DN32 | Class 2500 | Z28T Series

Metal seated valves GeneralUp to

�00 °C / 75� °F Up to

5�� °C / �000 °FUp to

650 °C / 1200 °FOrdering

code system

Std. port

Full port UnitBall port

AB C D H S W M N P F W TxL

Weightkg/lb

KvCvWelded Threaded

DN15 DN8, DN10 mm ��.�5 �7�.00 �07.00 50.00 ���.00 �9�.00 ��6.00 �50.00 69.50 5.50 �/�’’ UNF

7.�0 (F0�) �6.00M5x�

�.� 7.0

1/2” 1/4”, 3/8” inch 0.�� 6.�5 �.�� �.97 7.�7 7.5� �.50 5.9� �.7� 0.�� 0.�� �.�� 9.5 6.0

DN20 DN15 mm ��.00 ��9.00 ��0.00 60.00 ��7.00 �0�.50 ��9.00 ��0.00 9�.00 7.50 7/�6’’ UNF

7.�0 (F0�) ��.00M5x�

5.0 �0.0

3/4” 1/2” inch 0.5� 7.�� �.7� �.�6 7.�6 �.05 9.0� 9.06 �.�6 0.�0 0.�� �.65 ��.0 �.6

DN25 DN20 mm �0.65 �09.00 ���.00 6�.00 �96.50 ��6.00 �5�.00 ��7.00 �09.00 �.70 9/�6’’ UNF

7.�0 (F05) 50.00M6x�

�0.5 ��.0

1" 3/4” inch 0.�� �.�� 5.67 �.6� 7.7� �.90 9.9� 9.�� �.�9 0.�� 0.�� �.97 ��.� ��.�

DN32 DN25 mm �9�.00 ��5.00 �5�.00 6�.00 �0�.50 ���.00 �60.00 ��7.00 ���.00 �.70 9/�6’’ UNF

7.�0 (F05) 50.00M6x�

��.0 �9.0

11/4" 1" inch 7.60 �.�6 5.9� �.6� �.05 9.�7 �0.�� 9.�� 5.0� 0.�� 0.�� �.97 ��.6 ��.�

Page 24: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

5A

5B5C

1

2B

6

22

7

18

6A6

2A

18

25

24

13

4

11

15

9

12

16

3

14

17

10

8

26

29

45Metal seated valves

Components & materials

Metal seated valves

Size 1⁄4”- 11⁄4” | DN8-DN32 | Class 2500 | Z28T Series

Item Description Material speci�cation Qty.

8 Stop pin A5�� �0� �

9* Stem seal Graphite �

10 Follower B7�� ��6L �

11 Disc spring A69� 6�� �7-7PH �

12 Stem nut A�9� �M, EN�506-� A�-�0 �

13 Locking clip A�6� �, �A �

14 Handle A659 G�0�00 Zinc plate, A��0 ��0 �

15 Serrated washer A�9� 6 �

16 Handle nut A�9� �M, EN�506-� A�-�0 �

17 Sleeve PVC �

18 Body bolts A�9� B�M, A�9� B7 zinc plated,A5�� 660 ��-�6

22 Arrow �ow A�67 �0� �

23 Tag (not shown) A�67 �0� �

24 Bonnet seal Graphite �

25 Stem Bearing B6�7 N077�� Inconel 7�� , Bonze �

26 Bonnet A�79 ��6H, A�79 ���H, B6�7 N077�� Inconel 7�� �

29 Bonnet bolts A�9� B�M, A5�� 660 6

* Repair kit components

Item Description Material speci�cation Qty.

1 Body A�79 ��6H, A�79 ���H, A��� F��, B6�7 N077�� Inconel 7�� �

2A Downstream end A�79 ��6H, A�79 ���H, A��� F��, B6�7 N077�� Inconel 7�� �

2B Upstream end A�79 ��6H, A�79 ���H, A��� F��, B6�7 N077�� Inconel 7�� �

3Ball Base material: A��� F��6, A��� F��6H, A���

F6A Coating: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF)."

4 Stem B6�7 N077�� Inconel 7�� �

5ADownstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF)."

5BUpstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF)."

5C Upstream seat spring Inconel 7�� �

6* Body seal Graphite �

6A* Seat seal Graphite �

7*Stem thrust seal A�79 ��6L, Hardended with LTPN - Low

Temperature Plasma carboNitriding technology. B6�7 N077�� Inconel 7��

Page 25: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

D

C

H

S

B

A

ø Ball port

ø W

TxL threadF PCD

Preparationfor actuation

P

DD

Stem grooveshows valveball position

Square

N thread N thread

Q M M

M

46

Floating Ball Valves

Metal seated valves

Valve dimensions

Size 11⁄2”- 6” | DN40-DN150 | Class 1500 | Z28T Series

Metal seated valves GeneralUp to

�00 °C / 75� °F Up to

5�� °C / �000 °FUp to

650 °C / 1200 °FOrdering

code system

Std. port

Full port

UnitBall port

AB C D H S W M M DD Q N P F W TxL

Weightkg/lb

Kv

Welded Threaded Cv

DN40 DN32 mm ��.�0 ��7.00 �5�.00 95.00 �05.�0 ��7.�0 ���.00 �0���5.00 - ��.90 �0.00M�0x�.5

��.�5 (F07) 70.00M�x�0

�5 69

11/2” 11/4” inch �.�5 9.�� 6.06 �.7� �.�0 9.7� ��.�� �5.79 5.7� - 0.55 ��.00 0.5� �.76 55.0 �0

DN50 DN40 mm ��.�0 ���.00 �57.00 �05.00 �57.�0 �99.�0 ��5.00 600.00 ��5.00 - ��.90 �0.00M�0x�.5

��.�5 (F07) 70.00M�x�0

50 �0�

2" 11/2” inch �.50 9.�9 6.�� �.�� �0.�5 ��.79 ��.�9 ��.6� �.�6 - 0.55 ��.00 0.5� �.76 ��0.0 ��0

DN65 DN50 mm 5� �0�.00 �9�.00 ��5.00 �75.00 ���.50 ���.50 �0�.00 ��0.00 ��.90 �5.90 ��.70 �"-�� UNF-�A

��.50 (F�0) �0�.00M�0x��

�0 ��0

21/2” 2" inch �.0� ��.�9 7.6� �.9� �0.�� ��.56 �5.�� �5.79 9.�5 0.7� 0.6� 0.�9 0.7� �.0� �76.0 �56

DN80 DN65 mm 6�.75 �7�.00 �5�.00 ��0.00 �9�.�0 �6�.�0 - - �65.00 ��.�5 ��.75 �5.�0 ��/�"-�� UNF-�A

��.�0 (F��) ��5.00M��x��

��5 ��5

3" 21/2” inch �.5� ��.�� �0.00 5.5� ��.5� ��.�6 - - �0.�� �.�� 0.9� �.�9 0.95 �.9� �75.0 �50

DN100 DN80 mm �0 ��0.00 N/A ��0.00 �95.00 507.70 - - ��0.00 ��.�5 ��.75 �5.�0 ��/�"-�� UNF-�A

��.�0 (F��) ��0.00M�6x�0

�75 6�5

4" 3" inch �.�5 �6.�� N/A 5.5� �5.55 �9.99 - - ��.�0 �.�� 0.9� �.�9 0.95 5.5� ��5.0 7�0

DN150 DN100 mm �00 5�0.00 N/A �95.00 ��0.00 ���.00 - - �95.00 �5.90 �5.90 ��.50�" UN-�A

�0.00 (F�6) �65.00M�0x�5

��5 �7�

6" 4" inch �.9� �0.0� N/A 7.6� ��.90 ��.06 - - �5.55 �.�� �.�� �.7� �.�� 6.50 957.0 �0�0

(-) Due to high valve torque pipe handle cannot be used. A manual gear or automation means should be used to operate the valve.

Page 26: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

7

6

3

122

4

24

2529

8A

26

2B

6

18

5B

6A

1716

12

13

14

10

14B

9

2A

5A

5C

18

14A

8

Preparationfor actuation

11

47Metal seated valves

Components & materials

Metal seated valves

Size 11⁄2”- 6” | DN40-DN150 | Class 1500 | Z28T Series

Item Description Material speci�cation Qty.

9* Stem seal Graphite �

10 Follower B7�� ��6L �

11 Disc spring A69� 6�� �7-7PH �

12 Stem nut A�9� �M, EN�506-� A�-�0 �

13 Tab lock washer A��0 �0� �

14 Handle C.St. A�9 G�0�00 Zinc plate, A��0 ��0 �

14A Stop plate C.St. �.0�0� Zinc plate, A��0 ��0 �

14B Wrench head Ductile Iron A5�6 Gr. 65-�5-��, A��6 WCB, A�5� CF�M �

16 Wrench bolt EN�506-� A�-70/A�-�0, A�9� Gr B�/B�M �

17 Sleeve PVC �

18 Body bolts A�9� B�M, A�9� B7 zinc plated, A5�� 660 �6-5�

22 Arrow �ow A�67 �0� �

23 Tag (not shown) A�67 �0� �

24 Bonnet seal Graphite �

25 Stem Bearing B6�7 N077�� Inconel 7�� , Bonze �

26Bonnet A�79 ��6H, A�79 ���H,B6�7 N077��

Inconel 7���

29 Bonnet bolts A�9� B�M, A5�� 660 6-��

* Repair kit components

Item Description Material speci�cation Qty.

1 Body A�79 ��6H, A�79 ���H, A��� F��, B6�7 N077�� Inconel 7�� �

2A Downstream end A�79 ��6H, A�79 ���H, A��� F��, B6�7 N077�� Inconel 7�� �

2B Upstream end A�79 ��6H, A�79 ���H, A��� F��, B6�7 N077�� Inconel 7�� �

3Ball Base material: A��� F��6, A��� F��6H, A���

F6A Coating: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF)."

4 Stem B6�7 N077�� Inconel 7�� �

5ADownstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF)."

5BUpstream seat Base material: A��� F��6, A��� F��6H, A���

F6A Coating: Cr�C� - Chromium Carbide with Nickel Chrome binder (HVOF)."

5C Upstream seat spring Inconel 7�� �

6* Body seal Graphite �

6B* Seat seal Graphite �

7*Stem thrust seal A�79 ��6L, Hardended with LTPN - Low

Temperature Plasma carboNitriding technology. B6�7 N077�� Inconel 7��

8 Stop pin A5�� �0� �

Page 27: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

48

Floating Ball Valves

Metal seated valves

Ordering code systemThe HABONIM metal seated ball valve identi�cation code

� � � � 5 6 7 � 9 �0 �� �� �� �� �5 �6 �7 �� �9 �0 �� . �0

� 0 Z 7 � P - 6 6 6 M N G / � 5 0 -

Size Features Series Design Body/End Ball/Seats Stem Hardening Seals Connection Special Features

(�) The material code of construction identify between the two temperature segments.(�) For more information use Habonim control valves catalog. (�) Other end connections are available upon request.(�) Use �� Series without the 'P' su�x.

It is essential to provide as many details possible on the application such as: media, temperature, pressure, pipe line size and type of connection.

In some applications the available options above are limited to speci�c sizes. Consult with Habonim for details.

Size

Code inch mm

02 1/4” �5

03 3/8” �0

05 1/2” �5

07 3/4” �0

10 � �5

12 �1/4” ��

15 �1/2” �0

20 �” 50

25 �1/2” 65

30 �” �0

40 �” �00

60 6” �50

80 �” �00

Features

B Full bore

N(2) Control

D Diverter bottom entry

S Diverter side entry

Series

Z47 � Pcs design

Z28 High pressure design

Z73 Flanged ANSI �50

Z74 Flanged ANSI �00

Z78 Flanged DIN PN�6

Z78 Flanged DIN PN�0

Body / End connection

4ASTM A�05 C.StA��6 C.St WCB

6ASTM A�79 S.St. ��6/��6LASTM A�5� S.St CF�M/CF�M

F ASTM A�50 LF� C.St

I Inconel 6�5

P ASTM A��� F��

U ASTM A�79 ���

H ASTM A�79 ���H

D Duplex A995 CD�MN �A

K S.Duplex A995 CE�MN 5A

S �5�SMO A�5� CK�MCuN

Ball / Seats Set

6 ASTM A�79 S.St. ��6 / ��6L

G ASTM A�79 S.St. ��6Ti

L ASTM A�79 S.St. ��0H

N ASTM A�79 S.St. ��0

D D Duplex A�79 S���0�

K S.duplex A�79 S��750

S �5�SMO A�79 S���5�

Stem

M S.St. �7-�PH

Z Inconel 7��

Hardening

NLTPN - Low Temperature Plasma carboNitriding

ICr�C� - Chromium Carbide with Nickel Chrome binder - HVOF technique

OWC-Co - Tungsten Carbide with Cobalt binder - HVOF technique

E Stellite - PTA technique

Seals

G Expended Graphite

B NBR Sh. 90

V Viton Sh. 70

Special Features

V30(2) Characterized control downstream seat

WR DD Stem

FF Flat facing

RTJ Ring type joint facing

159 C ball

B Rolled bar

End Connection(3)

BSPT BS ��

DIN DIN �999 (BSPP)

NPT B�.�0.�

XBW Extended buttweld

XSW Extended Socket Weld

Flange connection

ANSI B�6.5 (B�6.�7 series A) - Raised Face�50, �00, 600, 900, �500, �500

EN �09� Pt.�&� Raised FacePN�6, PN�5, PN�0, PN6�, PN�00, PN�50, PN�00

Metal seated valves GeneralUp to

�00 °C / 75� °F Up to

5�� °C / �000 °FUp to

650 °C / ��00 °FOrdering

code system

Design

X -60 °C to ��0 °C (-76 °F to +��6 °F) HermetiX™ stem seal

P(4) -60 °C to +�00 °C (-76 °F to +75� °F)

T(1) -60 °C to +5�� °C (-76 °F to +�000 °F)

T(1) -60 °C to +650 °C (-76 °F to +��00 °F)

Page 28: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

49Metal seated valves

Metal seated valves

Page 29: Inspired By Challenge - Inkoinko.com.sg/image/data/CATALOG/HABONIM/MTM up to 538 and 650 deg C.pdf · 2 Floating Ball Valves Metal seated valves Introduction Metal seated ball valve

w w w . h a b o n i m . c o m

ISRAELHabonim HeadquarterTel: +972-4-6914911Fax: [email protected]

USAHabonim USAToll Free Phone: 1-866-261-8400Toll Free Fax: [email protected]

ChinaHabonim ChinaTel: + 86 21 64453190 *146Fax: + 86 21 [email protected]

UKHabonim UKTel: +44-1633-484554Fax: [email protected]

AustraliaHabonim AustraliaTel: +61 3 9556 [email protected]

www.habonim.com

Meta

l seat

ed

val

ves

12/1

5