7/25/2019 Inno Ds8000b

1/14

SITE M ASTERINNO DS8000B

Created by: Engr Russell SalazFM EngineerMobily 3 !ro"e#t

7/25/2019 Inno Ds8000b

2/14

SETTING THE LANGUAGE

!ress t$e Syste%&ey'

Cli#& t$e Instru%ent Settings so(t &ey' C$oose t$e )anguage (ro%

*o* u* %enu' +se +*,Do-n.ey'

Sele#t language so(t &ey' !ress Enter' Restart t$e de/i#e'

EnglishChinese

Enter

Created by: Engr Russell SalazFM EngineerMobily 3 !ro"e#t

7/25/2019 Inno Ds8000b

3/14

DF 1 DIS2NCE O F2+) MODE

ROCEDURE:

o Enter t$e Start and Sto* Fre4uen#y or #$oose t$e Band (ro% Band )ist &eo

C$oose -$i#$ ty*e o( #able is used' Cli#& Cable )ist %enu'o Calibrate t$e de/i#e'o Set t$e total distan#e i'e' (ro% NodeB to 2ntenna *ort 1lengt$ o( 5u%*er

Cables6indoor and outdoor7 and Feeder Cableo Set t$e Ma and Mini%u% 2%*litude7 #li#& 2%*litude 19 so(t &ey'o Set t$e Mar&er 1 ' Mar&er 9 1indoor "u%*er7 Mar&er; 1Feeder7 Mar&er3

1outdoor 5u%*ero !ress button to start t$e %easure%ent'o !ress !ea& 1? button to see t$e %ai%u% /alue o( your %easure%ent

and see t$e #orres*onding distan#e (ro% your %ar&er'

Created by: Engr Russell SalazFM EngineerMobily 3 !ro"e#t

7/25/2019 Inno Ds8000b

4/14

DTF M ODE

FRE@+ENCA B2ND

Enter t$e Start and Sto* Fre4uen#y or#$oose t$e Band (ro% Band )ist &ey'

Created by: Engr Russell SalazFM EngineerMobily 3 !ro"e#t

7/25/2019 Inno Ds8000b

5/14

DTF M ODE

C2B)E A!EC$oose -$i#$ ty*e o( #able is used'Cli#& Cable )ist %enu'

Created by: Engr Russell SalazFM EngineerMobily 3 !ro"e#t

7/25/2019 Inno Ds8000b

6/14

DTF M ODE C2)IBR2E: O!EN

Connect OPEN to RF port and then press continue.

Calibrate t$e de/i#e' !ress Cal button &ey'

Created by: Engr Russell SalazFM EngineerMobily 3 !ro"e#t

7/25/2019 Inno Ds8000b

7/14

DTF M ODE C2)IBR2E: S

7/25/2019 Inno Ds8000b

8/14

DTF M ODE C2)IBR2E: )O2D

If !"OR# calibration iscompleted

Connect $O%D to RF port andthen ress continue.

Created by: Engr Russell SalazFM EngineerMobily 3 !ro"e#t

7/25/2019 Inno Ds8000b

9/14

DTF M ODE

DIS2NCESet t$e total distan#e i'e' (ro% NodeB to 2ntenna *ort 1lengt$

5u%*erCables>>indoor and outdoor7 and Feeder Cable7 t$en *ressEnter &ey'

Created by: Engr Russell SalazFM EngineerMobily 3 !ro"e#t

7/25/2019 Inno Ds8000b

10/14

DTF M ODE

2M!)I+DESet t$e Ma and Mini%u% 2%*litude7 *ress 2%*litude 19 so(t

&a'(top)

&in

a' *alue should be higher than the +!,R alarm *alue . For e'ample f &&$ D!P +!,R the *alue measured is -/(./0) &a' *alue should

at least 1 or 2.

in *alue should at least be the ideal *alue 0. Created by: Engr Russell SalazFM EngineerMobily 3 !ro"e#t

7/25/2019 Inno Ds8000b

11/14

DTF M ODE

M2R.ERSet t$e Mar&er 1 ' Mar&er 9 1indoor "u%*er7 Mar&er; 1Feeder7

Mar&er31outdoor 5u%*er

&ar3er

!elect

&ar3

erO4on

&ar3erEdit

&ar3 the length of 5our cable sa5 indoor 6umpercable78m feeder cable782moutdoor 6umpercable78m. &078 &-78 &8710.

Created by: Engr Russell SalazFM EngineerMobily 3 !ro"e#t

7/25/2019 Inno Ds8000b

12/14

DTF M ODE

R+N,ME2S+REConne#t t$e RF #able to t$e RF !ort'

Created by: Engr Russell SalazFM EngineerMobily 3 !ro"e#t

!ress buttonto start t$e%easure%ent

7/25/2019 Inno Ds8000b

13/14

DTF M ODE

!E2. 2)+Eo !ress !ea& 1? button to see t$e %ai%u% /alue o( your

%easure%entand see t$e #orres*onding distan#e (ro% your %ar&er'

!ettings:

!#%R# FRE9 70-/&h; !#OP FRE9 7 -0

7/25/2019 Inno Ds8000b

14/14

DTF M ODE

)O2D SE>+!

Created by: Engr Russell SalazFM EngineerMobily 3 !ro"e#t

o I( you $a/e sa/ed set>u* #onguration 1 'sta7 you #an load itusing t$e )oadButton 1 ' $is -ill sa/e ti%e by not *er(or%ing t$e #alibration(or t$e e4ui*%ent'

Only

#$anget$eCablet5peDistance&ar3erand or%mplitude i(ne#essary'